| Age | Commit message (Collapse) | Author |
|---|
|
Add punctuation and fix a typo.
Change-Id: Ic61c665f7e2daefb50b478a1710ea66c8a88235a
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/28993
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
There is no need to indent these lines with two tabs.
Change-Id: I2164f4e3ea48db8dc5242a55b0452782dae19a4b
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/28989
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
The assignment of header->checksum was in some cases done twice, or
unnecessarily split into two lines.
Change-Id: Ib0c0890d7589e6a24b11e9bda10e6969c7d73c56
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/28988
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
|
|
While these pins were set to a pull-down 20KOhm, NPCX EC consumes
~2.1mW higher power. Becasue there was leakage current on both GPIO67
and GPIO70 from NPCX EC. With the external pull-up 10KOhm for
USB_OC0#/USB2_OC1#, this wasn't enough to prevent leakage current.
BUG=b:117139495
TEST=Check nxpc EC power to see power improvement
Change-Id: I685d876461c263f07ca4c8f8046635cb7087279c
Signed-off-by: Roy Mingi Park <roy.mingi.park@intel.com>
Reviewed-on: https://review.coreboot.org/29007
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Pratikkumar V Prajapati <pratikkumar.v.prajapati@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
CPU_MICROCODE_CBFS_LEN and CPU_MICROCODE_CBFS_LOC configs pass the CPU
microcode length and base address in CBFS to FSPT binary as init parameters.
Add new config FSP_T_XIP in Kconfig, which is selected by platform config.
If FSP_T_XIP is selected, then relocate FSPT binary while adding it in CBFS
so that it can be executed in place.
BUG= None
TEST= Build for both CFL RVP11 & RVP8 and verified for successfull CAR setup.
Change-Id: Ic46e0bb9ee13c38ff322979119c4813653c61029
Signed-off-by: praveen hodagatta pranesh <praveenx.hodagatta.pranesh@intel.com>
Reviewed-on: https://review.coreboot.org/28985
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Update CPU passive temperature threshold value from 70C to 80C,
to avoid early throttling for spiky workloads. Also, change CPU
throttling interval from 1 sec to 5 sec for CPU temperature.
BUG=b:116400298
BRANCH=None
TEST=Manual performance testing on nocturne.
Change-Id: Ic5031a4aa16f750237565f4e4928e78834b1d686
Signed-off-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/29044
Reviewed-by: Puthikorn Voravootivat <puthik@chromium.org>
Reviewed-by: Todd Broch <tbroch@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
It always included if ACPI is supported since commit 822bc65 with
Change-Id I372dbd03101030c904dab153552a1291f3b63518 ("ACPI: Remove
CONFIG_GENERATE_ACPI_TABLES").
Change-Id: If17a6f43e368ccf850031b349714fa1ec4d02c1d
Signed-off-by: Peter Lemenkov <lemenkov@gmail.com>
Reviewed-on: https://review.coreboot.org/28954
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Change-Id: I29953250ca278d5b1977be3763359df5110f67c7
Signed-off-by: Wonkyu Kim <wonkyu.kim@intel.com>
Reviewed-on: https://review.coreboot.org/29004
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Since there are two cameras on Nami and only one camera on Syndra.
We need to disable rear camera/DMIC on all Syndra sku.
BUG=b:112876867
Change-Id: I92fb43ec84387c268ffdb6d0d34a5e5b13bcf50a
Signed-off-by: Amanda Huang <amanda_hwang@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/29022
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
For debugging purposes always set the pciaddr attribute.
Tested on Lenovo T500.
Change-Id: I83a0e7f7196ed251fa0becc4e56bef3ca68f20f4
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/18599
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Tried to build all affected mainboards - still compiles fine.
Change-Id: I385cac1a75cee13453b831bd75b3ecc7a6d229fa
Signed-off-by: Peter Lemenkov <lemenkov@gmail.com>
Reviewed-on: https://review.coreboot.org/29033
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
This define is no longer used by anyone. It was removed everywhere else
with commit with Change-Id I556769e5e28b83e7465e3db689e26c8c0ab44757.
It seems that these two files were simply mislooked. So let's remove it.
Change-Id: Ifbb62441e16e97c0cae0713968844e296619a880
Signed-off-by: Peter Lemenkov <lemenkov@gmail.com>
Reviewed-on: https://review.coreboot.org/29070
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
This mainboard is quite similar to the p5qc. The main differences being a second
PEG slot, the IDE slot and being DDR2 only.
The following was tested:
- both PEG slots populated (coreboot sets legacy VGA decoding on the GPU in the
black slot)
- USB
- Ethernet NIC
- PS2 Keyboard
- COM1
- S3 resume
Change-Id: I49a4bca4256e2a905aff3252eca76387c81152c1
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/29102
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
A shortcoming of this driver is that if multiple devices with the same PCI ID
are present and don't have an eeprom, they would all get the same macadress set.
The r8168 driver deals with such cases so it should be easy to implement if
needed.
Change-Id: I5c32df00e25453c350a45e7f1ee6834b89c4289f
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/28265
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
SeaBIOS does not seem to like the Marvel IDE controller, so disabled SeaBIOS
support for ATA. It works fine in Linux afterwards.
Working:
- SATA on southbridge port
- SATA on marvel IDE controller ports (only in Linux)
- USB
- COM1
- PS2 Keyboard
- DDR2 DIMMs
- PCIe x16 PEG port
- PCI port
- NIC (needs a driver to set macaddress)
- S3 resume
Not working:
- SeaBIOS with ATA support (long timeout marvel controller so disabled)
- DDR3 fails because the proper clock signal does not get enabled. Even when
fixing this it fails later or during memtest, so it should be considered
unsupported for now
Untested:
- PCIe x1 ports (expected to work)
- sound (expected to work)
TODO:
add documentation
Change-Id: I4a81940707566776bd048904ca1387fea741fece
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/28264
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
More platforms are not able to hibernate under certain circumstances,
such as when AC is plugged. This original path was conservatively put in
to prevent potential damage when cr50-update-caused asynchronous resets
occur. Julius' compelling argument that async resets from recovery mode
requests should have enough coverage of the design over the course of
project development. Remove the hibernate path and assume all is well
going forward.
Change-Id: I37121e75ff4e6abcb41d8534a1eccf0788ce2ea2
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/29076
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Jett Rink <jettrink@chromium.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
It looks like on the ASUS P5QC has 0 in this CAPID field while still supporting
TCK_666MHZ.
Change-Id: Id1a94d91434dbe782fcc56dad56fcaee4e78463b
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/29101
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Change-Id: I4a9a9366c85206fa460519a26f48b3aada5bc7c3
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/29100
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
While during the read training itself only the settings for rank 0 are used for
all ranks, the controller does use the separate settings for each rank later on.
It is unknown which register is responsible for this.
The signals are probably not generated separately and therefore need to have the
same settings for all ranks. Therefore program the results for all ranks instead
of for all populated ranks.
TESTED: Fixes DG43GT not booting with only the second DIMM slot of a channel
populated.
Change-Id: I7965a068ef4779847e62e966154764370c91302a
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/28577
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Fix a typo and make comments more consistent (start with
capital letter).
BUG=None
TEST=None
Change-Id: I97bff5e05596fc6973f0729e276a2e45b291120d
Signed-off-by: Joel Kitching <kitching@google.com>
Reviewed-on: https://review.coreboot.org/29025
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
|
|
Make #define definitions for PMxEF and replace the hardcoded values.
Note that this doesn't change the current functionality of the source.
The existing code has been propogated from the sb//hudson port, which
seems to attempt to enable 100% of all OHCI and EHCI controllers that
may be present in the system.
Change-Id: I6018b0062730de19e3283a010144dfedc2b11423
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/29075
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Remove nonpreset controllers from the PCI device identifier function
(ignoring any CONFIG_USBDEBUG_HCD_INDEX). The extra devices appear
to be holdovers from the original sb/hudson source.
TEST=Jam Makefile.inc to unconditionally build enable_usbdebug.c and
verify proper BDF is returned in romstage and ramstage.
Change-Id: I2e819d5e998922ad427c4a094c29a590f249a0d3
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/29074
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Delete an unmatched opening parenthesis in the definition for the EHCI
hub config register definition. This wasn't causing a problem unless
EHCI debug was enabled.
TEST=Jam Makefile.inc to unconditionally build enable_usbdebug.c and
verify successful build
Change-Id: I5f461d1573e416b5a8ee24329142e3c46b6a05e3
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/29073
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Move the SPI base address register definition to D14F3. This was
missed in:
bba043 amd/stoneyridge: Rearrange southbridge.h
Change-Id: Ia722339418c118bdf4b000bbf97ae4266e9b3be2
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/29072
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
This is a no-op on non-FSP systems, but enables using it when supported.
Change-Id: I66fe9b8587753ea017e13a752a7728e47287e9a0
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/28776
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
|
|
Change-Id: I0032e86755750755e7ae6e2a53863e1600f96a5b
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/29030
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
|
|
With https://github.com/IntelFsp/FSP/pull/4 merged, this allows using
Intel's FSP repo (that we mirror) to build a complete BIOS ifd region
with a simple coreboot build, automatically drawing in headers and
binaries.
This commit covers Apollolake, Coffeelake, Skylake, and Kabylake.
Skylake is using Kabylake's FSP since its own is FSP 1.1 and Kabylake's
also supports Skylake.
Another candidate (given 3rdparty/fsp's content) is Denverton NS, but
it requires changes to coreboot's FSP bindings to become compatible.
Cannonlake, Whiskeylake require an FSP release.
Change-Id: I8d838ca6555348ce877f54e95907e9fdf6b9f2e7
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/28593
Reviewed-by: Pratikkumar V Prajapati <pratikkumar.v.prajapati@intel.com>
Reviewed-by: Naresh Solanki <naresh.solanki@intel.com>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch adds remote GDB support for the arm64 architecture.
Change-Id: I2fa4dbca6c39f822f489a5e81bd052f53fda98a5
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/29020
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
The arm32 GDB architecture code contains a little hack that allows it to
(sort of) correctly deal with a reentrant exception triggered from
within the GDB stub. The main logic for this isn't really arm32 specific
and could be useful for other architectures as well, so factor it out
into a separate function.
Change-Id: I3c6db8cecf1e86bba23de6fd2ac9fdf0cf69d3c6
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/29019
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This patch reworks the arm64 exception handling to be more similar to
how it works on arm32. This includes a bunch of features like actually
saving and restoring more exception state in the exception_state
structure and supporting the same sort of partial reentrancy that is
useful for GDB. Since there's no instruction to directly load into or
store out of SP on arm64, we can't do quite the same thing where we use
that to read an exception_state_ptr variable right after exception entry
when no other register is available. But we can do something very
similar by (ab-)using the "high" stack pointer (SP_EL2) as a pointer to
the exception_state struct and providing a function to change it.
Change-Id: Ia16a1124be1824392a309ae1f4cb031547d184c1
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/29018
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This patch adds the new, faster architectural register accessors to
libpayload that were already added to coreboot in CB:27881. It also
hardcodes the assumption that coreboot payloads run at EL2, which has
already been hardcoded in coreboot with CB:27880 (see rationale there).
This means we can drop all the read_current/write_current stuff which
added a lot of unnecessary helpers to check the current exception level.
This patch breaks payloads that used read_current/write_current
accessors, but it seems unlikely that many payloads deal with this stuff
anyway, and it should be a trivial fix (just replace them with the
respective _el2 versions).
Also add accessors for a couple of more registers that are required to
enable debug mode while I'm here.
Change-Id: Ic9dfa48411f3805747613f03611f8a134a51cc46
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/29017
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Patrick Rudolph <patrick.rudolph@9elements.com>
|
|
The AMD implementation of this register is only 16 bits. Change the
source accordingly.
TEST=Suspend/Resume a Grunt several times
Change-Id: Ib900468cc1c790fa7d57bb6faa91aee012173f7a
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/29016
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
|
|
Shorten the names in the MISC CGPLL_CONFIG, and make the formatting match
the surrounding source.
Change-Id: I71cf1ff6bd4bca7a25484b4da9388c17cfecc043
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/29015
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
|
|
Make the field names of the MISCx00 GPPClkCntrl more manageable by
shortening their names. Make the definitions look more like the
rest of the header file.
Change-Id: I515cd664808e38851a7dbdba899df4fb9bbbcde6
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/29014
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
|
|
Group definitions so they're near others of the same type, e.g. PCI,
AcpiMmio, etc.
Change-Id: Ia6ef21431db0e758eba0ea043b54c036ec6235fe
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/29013
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
|
|
Delete definitions that are no longer used.
Change-Id: I94c9c33f73c1a2d9308408e3e9ca526e876d6135
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/29012
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
|
|
Change-Id: I1b44ffd7c0244b0408c3823d634a9b8d5038462f
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/29011
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
|
|
Make the whitespace match surrounding lines and remove unnecessary
parentheses.
Change-Id: I2ed02494ba69237c38af61317e435d9575cefe1c
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/29010
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
|
|
Match the rest of the soc/stoneyridge source.
Change-Id: I4531e6dad0362be73499647d9fc93c168b6f163e
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/29009
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
|
|
Delete artifacts remaining from the original "hudson" and "yangtze"
controller hub designs.
Husdon devices had a configurable AcpiMmio base address, and a selection
for I/O vs. MMIO decode. Modern products are fixed at 0xfed80000 in MMIO.
Remove the flash control register definitions for the old generations.
The manual reset register appears to not function as hudson.
PMIO_DEBUG is named differently now, and not used, so remove its
definition too.
Change-Id: I6484bb2ca80b65318565dfee1a3368b121aea9de
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/29008
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
|
|
This change implements the callback to provide google_chromeec_event_info
structure in nocturne variant and sets MKBP SCI based on board id.
BUG=b:112366846,b:112112483,b:112111610
Change-Id: Ifcc10aefc8f450214bd64dfffaf8854ada43f323
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/28984
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Enrico Granata <egranata@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This change adds a variant callback to read google_chromeec_event_info
from variant at runtime to allow override of any events based on
factors like board id.
This callback is used in ramstage and smm to get
google_chromeec_event_info structure for performing various actions
like setting masks and logging wake events from EC.
BUG=b:112366846,b:112112483,b:112111610
Change-Id: If89e904c92372530a0f555952f87702f068e0b03
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/28983
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Enrico Granata <egranata@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This change adds ec_boardid.c to smm stage, which is required to allow
mainboards to query the ec to get board version in this
stage.
BUG=b:112366846,b:112112483,b:112111610
Change-Id: Iccbba96ebb94a12745a62cbfe3496f9e6f921e3d
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/28982
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Enrico Granata <egranata@chromium.org>
|
|
There doesn't seem to be a reason why we would want to protect certain
chromeec functions with __SMM__ guard. So, this change gets rid of
it. If the functions remain unused, then they would be removed during
linking.
Change-Id: I8196406074b01fe8ea15173c55d45bb86384be1b
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/29006
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Enrico Granata <egranata@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Use "cpu/x86/msr.h" for common IA-32 MSRs and correct IA-32 MSRs names.
Change-Id: Ida7f2d608c55796abf9452f190a58802e498302d
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/28752
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Pratikkumar V Prajapati <pratikkumar.v.prajapati@intel.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I849dd406f5ccc733d4957eaf1c774745782f531a
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/28784
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
STAPM devicetree registers do not indicate the unit, which causes confusion.
More importantly, the time was assumed to be in seconds when it's actually
milliseconds. This caused early STAPM configurations to fail.
BUG=b:117590953
TEST=Build grunt
Change-Id: I2a7e3d43601992d1f7b02456913c763d940fe9ee
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/29035
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
With correct stapm values audio issue is not observed with
PsPPBalanceLow (Gen1 speed).
BUG=b:117569918
TEST=audio playback multiple times
Change-Id: Iaeae52b262b12622a6753432e3fc40bf5f0fd8e0
Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com>
Reviewed-on: https://review.coreboot.org/29028
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
stapm_time passed to smu via agesa is in msec. With earlier value
smu was getting stapm_time as 2.5 sec instead of 2500 sec and thus
causing issue in S3, and audio in PsppBalanceLow state.
BUG=b:117569918, b:117252463
TEST=
1.) audio works with PsppBalanceLow
2.) S3 cycles
Change-Id: I673e7e673d042918dff47141f37bbca354f5c45c
Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com>
Reviewed-on: https://review.coreboot.org/29027
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Bounce buffers used to be used in those cases where the payload
might overlap coreboot.
Bounce buffers are a problem for rampayloads as they need malloc.
They are also an artifact of our x86 past before we had relocatable
ramstage; only x86, out of the 5 architectures we support, needs them;
currently they only seem to matter on the following chipsets:
src/northbridge/amd/amdfam10/Kconfig
src/northbridge/amd/lx/Kconfig
src/northbridge/via/vx900/Kconfig
src/soc/intel/fsp_baytrail/Kconfig
src/soc/intel/fsp_broadwell_de/Kconfig
The first three are obsolete or at least could be changed
to avoid the need to have bounce buffers.
The last two should change to no longer need them.
In any event they can be fixed or pegged to a release which supports
them.
For these five chipsets we change CONFIG_RAMBASE from 0x100000 (the
value needed in 1999 for the 32-bit Linux kernel, the original ramstage)
to 0xe00000 (14 Mib) which will put the non-relocatable x86
ramstage out of the way of any reasonable payload until we can
get rid of it for good.
14 MiB was chosen after some discussion, but it does fit well:
o Fits in the 16 MiB cacheable range coreboot sets up by default
o Most small payloads are well under 14 MiB (even kernels!)
o Most large payloads get loaded at 16 MiB (especially kernels!)
With this change in place coreboot correctly still loads a bzImage payload.
Werner reports that the 0xe00000 setting works on his broadwell systems.
Change-Id: I602feb32f35e8af1d0dc4ea9f25464872c9b824c
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: https://review.coreboot.org/28647
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Fixes builds of that binary in clean trees.
Change-Id: If5a995449a74c00da836fcf22bda44ebc8197518
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/28994
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
In romstage malloc is not available, so use CAR_GLOBAL
variable instead.
BUG=b:78106689
TEST=Boot to OS
Change-Id: If9438d0b707c6ffaa61db80bd1d385112bc91cfc
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Reviewed-on: https://review.coreboot.org/25067
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
These codes are written by me based on the privileged instruction set.
I tested it by qemu/riscv-probe.
Change-Id: I2e9e0c94e6518f63ade7680a3ce68bacfae219d4
Signed-off-by: Xiang Wang <wxjstz@126.com>
Reviewed-on: https://review.coreboot.org/28569
Reviewed-by: Philipp Hug <philipp@hug.cx>
Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Remove assert() and instead use if statement to check if
comm->groups is NULL.
Found-by: klockwork
BUG=None
TEST=Boot to OS
Change-Id: I85a6bc700b52d04c61ca8f2baac62000f40cf2cb
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Reviewed-on: https://review.coreboot.org/28940
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Tune I2C params for I2C buses 0, 5, 6, and 7 to ensure that the
frequency does not exceed 400KHz.
BUG=b:117298114
TEST=emerge-octopus coreboot chromeos-bootimage and measured frequency
under 400 KHz
Change-Id: Id608aae7edf54a24f364606dd7952521d1d67c1a
Signed-off-by: Wisley Chen <wisley.chen@quantatw.com>
Reviewed-on: https://review.coreboot.org/29021
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Printing "Autobuild finished" after the autobuild server exits (which
normally doesn't happen) is not very useful.
Change-Id: I909d7ab5f399993dbb1916e66ba94c48d7bc53bf
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/28992
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Fixes: b159d5ba8f ("riscv: add documentation for stages and payloads")
Change-Id: I5ca8ed094c9b6d115da707375205872e782a66b2
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/28991
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
A colon usually indicates that something related follows. But in
Documentation/releases/index.md, nothing followed. Fix this by swapping
two lines.
Change-Id: I3e2750c208a2b725145b94615f64381ac763f0dc
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/28990
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Mentioned patch could not be applied in coreboot-sdk:1.52. With this fix
patch apply correctly.
Change-Id: I130856520f91bcfbd9a62741b1d5abb6495a6eac
Signed-off-by: Piotr Król <piotr.krol@3mdeb.com>
Reviewed-on: https://review.coreboot.org/27614
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
|
|
Only two UARTs are connected to the FTDI UART USB chip.
Change-Id: Id5ae7266ce44c9f64c7f7aeaf23c49122041f47a
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/28986
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
|
|
This change sets PCIEXPWAK_DIS in PM1_EN register if WAKE# pin is not
enabled on the platform. This is required to prevent unnecessary wakes
if the WAKE# pin remains not connected on the platform. Function to
set PCIEXPWAK_DIS gets called in normal boot path (BS_PAYLOAD_LOAD) as
well as S3 resume path (BS_OS_RESUME).
BUG=b:117284700
TEST=Verified that no spurious wakes are observed on nocturne.
Change-Id: Iea93baffc9bb703c0ffedacafc6a9a9410c7ebfe
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/28939
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
|
|
Need to tune I2C bus 0 clock frequency under the 400KHz
since this bus attached the Stylus EMR pen and need meet the spec.
Bug=b:117297214
TEST=flash coreboot to the DUT and measure I2C bus 0 clock
frequency whether under 400KHz
Change-Id: I06d9d25f52d7f641d937de0d6b7df3d7a076fbf9
Signed-off-by: Peichao.Wang <peichao.wang@bitland.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/28973
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The dimm_info and memory_info structs are used in devices that
don't strictly use DIMMs. Those platforms have the DRAM soldered
down so there's no DIMM part number that encapsulates the DRAMs
used in the DIMM. The full part number is desired to be exposed in
the SMBIOS tables. As such extend DIMM_INFO_PART_NUMBER_SIZE to 33
to accommodate longer part numbers
'MT53B256M32D1NP-053 WT:C' is one of the longer part numbers that
are desired to be maintained.
BUG=b:115697578
Change-Id: I0c39dd1d1c2f0776d70d8c4d8d56719779ff82ae
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/28978
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jett Rink <jettrink@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Now only those UARTs that are enabled in devicetree.cb are initialized.
Tested on Opencellular Elgon.
Change-Id: I145c224148f0cc078bb1c76f588f603e73121a62
Signed-off-by: Jens Drenhaus <jens.drenhaus@9elements.com>
Reviewed-on: https://review.coreboot.org/28975
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
Add SPD file for sdp samsung_dimm_K4AAG165WB-MCRC (ram id: 9)
BUG=b:112679174
TEST=emerge-nami coreboot chromeos-bootimage
Change-Id: Iac1e3ca4b009cc9be94608cd342f535fa581a5eb
Signed-off-by: Chris Zhou <chris_zhou@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/28974
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Use the new I2C slave reset function and reset all slaves connected to all
4 I2C. Do this in all boards.
BUG=b:114479395
TEST=Added debug code. Build and boot grunt. Examined output, confirmed
GPIO pins changing as required. Removed debug code.
Change-Id: Ia78ee5d5319d3c1a7daa9c56c81d435999b3a359
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/28575
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
AMD's SOC do not wait for I2C transactions to complete before executing
a reset. Because of this, it's possible for the reset to happen in the
middle of a transaction, resulting on a slave hang. There are 2 possible
solutions:
If the slave has a reset pin connected to a GPIO pin, it can be used to
reset the slave, else the only solution is to bang SCL 9 times. Create
code that makes it easy to implement SCL bang, using a devicetree
register to define which I2C SCL lines needs to be reset.
BUG=b:114479395
TEST=Build and boot grunt. Look at transactions on a scope.
Change-Id: I7f74b7e45c509044825355874753969f074e2382
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/28574
Reviewed-by: Daniel Kurtz <djkurtz@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=b:117173908
TEST=Build delan
Change-Id: If149b8c43ff16637c38d5320eb606bb72d62e953
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/28972
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Clean up Kconfig file in order to support variants for fizz. Add
BOARD_GOOGLE_BASEBOARD_FIZZ that can be set by various fizz variants
to use the common baseboard configs.
BUG=b:117066935
BRANCH=Fizz
TEST=emerge-fizz coreboot
Change-Id: I9c89f1dc526a9d623e1ae4d4b52a923489b389d3
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/28959
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Set up DRAM related PLLs.
And update post divider table to fulfill all freqency settings.
BUG=b:80501386
BRANCH=none
TEST=Boots correctly on Kukui
Change-Id: Ic197cef7d31f75ffe4e7d9e73c9cc544719943ab
Signed-off-by: Tristan Shieh <tristan.shieh@mediatek.com>
Signed-off-by: Weiyi Lu <weiyi.lu@mediatek.com>
Reviewed-on: https://review.coreboot.org/28667
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Joel Kitching <kitching@google.com>
|
|
Fixes: 4d8b843d37 ("Rename documentation -> Documentation")
Change-Id: I423cb159ca3c837ed52937dc6d76d9a43a069256
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/28634
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
There is no datasheet available for this SuperIO, but dumping all
possible registers on a Dell Optiplex GX520 resulted in data that was
similar to other supported chips. Data also matches what is set in the
BIOS, e.g. the parallel and serial ports' addresses.
Change-Id: I768e4b5ec1e73c53e1a2355e0a0657b7a5ccbb89
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/28958
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
This patch creates _PRT entires for each PCIE root port devices.
TEST=Able to see PCIE wake device in cat /proc/acpi/wake list
Change-Id: I183c89c92139e15e0bfc39620710dbdc6597b351
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/28800
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This patch provides option for PCI IRQ mapping in both PIC and APIC mode.
TEST=Build and Boot on CNL RVP.
Change-Id: Ie26750ac9dc2ce940b0c116085c041de439075df
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/28799
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
issue
This patch fixes below ACPI compilation issue:
Found 1 external control methods, reparsing with new information
Pass 1 parse of [DSDT]
ACPI Error: [EPCS] Namespace lookup failure, AE_ALREADY_EXISTS (20160318/dsfield-660)
ACPI Error: [EMNA] Namespace lookup failure, AE_ALREADY_EXISTS (20160318/dsfield-660)
ACPI Error: [ELNG] Namespace lookup failure, AE_ALREADY_EXISTS (20160318/dsfield-660)
Pass 2 parse of [DSDT]
ACPI Warning: NsLookup: Type mismatch on EPCS (Integer), searching for (RegionField) (20160318/nsaccess-664)
ACPI Warning: NsLookup: Type mismatch on EMNA (Integer), searching for (RegionField) (20160318/nsaccess-664)
ACPI Warning: NsLookup: Type mismatch on ELNG (Integer), searching for (RegionField) (20160318/nsaccess-664)
Parsing Deferred Opcodes (Methods/Buffers/Packages/Regions)
TEST=Able to build sgx.asl without any ASL error.
Change-Id: If4e7d4c66b6aab6c081fa272d8c2c9a1f0651ef7
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/28961
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This patch to fix KW issue due to msg, data and response pointers NULL
check fail.
Change-Id: I39324514079f240ba1683a04e579de85485299bf
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/28949
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Legacy PME are enabled by default in FSP-S UPD. This policy sets
PME Interrupt Enable (PIE) bit of RCTL register to trigger interrupt
generation when RSTS.PS state has changed (either due to 0->1 transition
or due to this bit being set with RSTS.PS already set). Due to this
interrupt generation, system wakes from sleep immediately it enters.
This patch overrides root port legacy pme upd policy from coreboot to
ensure no false SCI is triggerd when system is in S3/S0ix state.
BUG=b:113083354
BRANCH=none
TEST=Able to make S3 resume using wake on wifi connect/disconnect usecase
without any failure.
Change-Id: I779fac711eeeed65ea379fad1cc400052d8a00eb
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/28947
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This patch save and restore ITSS IPCx register before and after
FSP-S call.
Change-Id: Iea9356b4404d2fa49ea62ef7bc2c72f125054ff3
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/28792
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch save and restore ITSS IPCx register before and after
FSP-S call.
Change-Id: Ib731f27826d604c305dc52a8488fd6240b01148a
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/28791
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This patch selects Kconfig for Intel Core Platform in order to ensure
proper ITSS IPCx programming.
Change-Id: I81e75e17ceb23c364b78300c3950144be1580700
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/28790
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
After adjustment on Liara EVT
H1: 392.03 KHz
TP: 397.87 KHz
TS: 397.71 KHz
BUG=b:116309237
BRANCH=master
TEST=emerge-grunt coreboot chromeos-bootimage
measure by scope
Change-Id: Ib5d7ce09ac58f33ee826d7541e1a0d14a03add9a
Signed-off-by: Chris Zhou <chris_zhou@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/28960
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Some payloads don't depend on their supported platforms, which makes
them visible in menuconfig even if they are not supported (yet).
Change-Id: Ia1ec0f0ca0b6521d0c024500c67326337f3d744f
Signed-off-by: Philipp Hug <philipp@hug.cx>
Reviewed-on: https://review.coreboot.org/28774
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
|
|
Change-Id: Ic122b3eaed54e29bbb3e11de84822169c81c04eb
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/28928
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
The SCH3112, SCH3116 and SCH5127 were lacking a pin dump. Since their
datasheets are available, add their pin dumps.
The SCH3112, SCH3114 and SCH3116 are almost identical, they only differ
in the number of serial ports. Some values in the SCH3114 dump were
inaccurate, that has been fixed as well.
Datasheets used:
- SCH311X: DS00001872A
- SCH5127: DS00002081A
Change-Id: Ic985526be9b09e0452eaf883904dfaf709b7e907
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/28794
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Setting default PSPP setting to BalancedLow was causing audio
playback issue in most of the units. With BalancedLow either there
was no sound or noise on playback.
Switching to BalancedHigh as default option.
BUG=b:116553085, b:112020107
TEST=Test playback and hear proper audio.
Change-Id: Ibf64d7b8e58e60ce931ddc85f11b135708cdb1ee
Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com>
Reviewed-on: https://review.coreboot.org/28967
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
Reviewed-by: Daniel Kurtz <djkurtz@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Its spreading copies got out of sync. And as it is not a standard header
but used in commonlib code, it belongs into commonlib. While we are at
it, always include it via GCC's `-include` switch.
Some Windows and BSD quirk handling went into the util copies. We always
guard from redefinitions now to prevent further issues.
Change-Id: I850414e6db1d799dce71ff2dc044e6a000ad2552
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/28927
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This patch fixes KW issue due to pointer being NULL and will be dereferenced
Change-Id: Iedb59daf5f448e31c0097873a086e4d08cd4a979
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/28948
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable DRAM_PART_NUM_IN_CBI feature to get DRAM part number from CBI
and set DRAM_PART_IN_CBI_BOARD_ID_MIN to 3 for DVT.
BUG=b:115697578
TEST=verified it in Bobba EVT board which rework ram id.
Change-Id: I0fb457d8772f5038e5d90188d7682956ddfad46b
Signed-off-by: Pan Sheng-Liang <sheng-liang.pan@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/28891
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
It exposes an interface that is as generic as possible, so payloads
and/or kernels can use it for their data.
Change-Id: I9553922f9dfa60b9d4b3576973ad4b84d3fe2fb5
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/25182
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I6b40aaf5af5d114bbb0cd227dfd50b0ee19eebba
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/28934
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Wifi wake register is incorrectly set in devicetree.
Set wifi wake to its correct wake source, GPE0_DW2_01.
BUG=b:117330593
TEST='emerge-nocturne coreboot chromeos-bootimage', flash nocture,
connect wifi to a hotspot, suspend device, echo freeze >
/sys/power/state, and then shutdown the hotspot and verify device
wakes.
Change-Id: Iafa865ca79d33541d7f47b69d2fb209e7f9c98af
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/28938
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The WAKE# signal has moved to LAN_WAKE, so WAKE# is now
floating and must be disabled. This change disables WAKE#.
BUG=b:117284700
TEST=none
Change-Id: I1c25e4ba28cd2b8807cd155d47c29c0d3ee9e8a5
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/28926
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Change-Id: I233e835180fd445961b6deb74ea7afc2821c236e
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/28909
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
* Convert PNG to JPG and reduce image quality.
* Mark flash IC and USB serial connector.
* Mark SPI programming header.
* Add programming header pinout.
Change-Id: Ica5958545ed23573a0d48dfa422ad1a822d06b47
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/28966
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
|
|
* Add Makefile dependency to source file
* Add argument support
* Add help support
* Print usage on wrong arguments
* Add support for parsing VBT binary file
* Add support for parsing PCI Option ROM
* Add support for writing VBT binary file
* Add support for patching PCI Option ROM
* Keep support for accessing legacy VGA area Option ROM
* Keep support for dumping VBT contents to stdout
Allows to extract VBT, analyse VBT and patch PCI Option ROMs as needed.
The required arguments have been changed:
./intelvbttool --<SOURCECMD> [filename] --<DESTCMD> [filename]
SOURCECMD set the VBT source. Supported:
inlegacy : Legacy BIOS area at phys. memory 0xc0000
invbt : Read raw Intel VBT file
inoprom : Read VBT from Intel Option ROM file
DESTCMD set the VBT destination. Supported:
outdump : Print VBT in human readable form
outvbt : Write raw Intel VBT file
patchoprom: Patch existing Intel Option ROM
Any combination of SOURCECMD and DESTCMD is possible.
Change-Id: I8cbde042c7f5632f36648419becd23e248ba6f76
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/18902
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
|
|
SiFive's website was reorganized, which broke our links to PDF files.
Update these links to the current ones, obtained by browsing
https://sifive.com/documentation/.
Change-Id: I312de84bf12abb0789bdd971c40033f1e4ea0dd1
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/28952
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
coreboot does not set up virtual memory anymore.
Change-Id: I231af07b2988e8362d1cdd606ce889fb31136ff1
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/28831
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philipp Hug <philipp@hug.cx>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
RISC-V is not a project of the University of California, Berkeley,
anymore; it stands on its own feet now.
Remove the "UCB" component from the RISC-V mainboards in the "emulation"
directory, and don't set MAINBOARD_VENDOR to UCB, either.
Change-Id: I301d9d0091a714e62375052e5af06a9197876688
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/28951
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
In order to make the macro name consistent for all PAD_CFG1_IOSSTATE_*
macros, this change uses lower case x for *RXD*. It helps avoid
confusion when using the macros.
Change-Id: I6b1ce259ed184bcf8224dff334fcf0a0289f1788
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/28924
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
All ampton boards should have the DRAM info configured in CBI and so
DRAM_PART_NUM_ALWAYS_IN_CBI is already selected for ampton. This
change gets rid of the redundant minimum board id value for Ampton.
BUG=b:117071184
Change-Id: I59f60b8c5aa34b55b8e473c06cc49ea7ae284d62
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/28933
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Jett Rink <jettrink@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
