| Age | Commit message (Collapse) | Author |
|---|
|
Change-Id: I36ed2c33f9bed3e640871283c2cb163d6800d1d5
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/28289
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
The firmware of devices connected to LPC should deassert the LPC CLKRUN#
signal when there is no bus activity on LPC.
Necessary changes:
- Enable LPC CLKRUN#
- Enable LPC PCE (Power Control Enable)
- Enable LPC CCE (Clock Control Enable)
- Remove I/O decoding range on LPC for COM 3
- Disable I/O UART driver
Change-Id: I2fd80e3fdcf23658f97b8182a77df7e09ddf25d6
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/28268
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Only Ids.h had definitions still in use, and they were removed or moved to
AGESA.h. Now Ids.h, IdsPerf.h and IdsLib.h can be safely removed.
BUG=b:112885948
TEST=Build grunt
Change-Id: I031ae8eb5f34fee801365fc89ea11a881211e726
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/28299
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Google is creating code to measure AGESA performance, which needs structure
TP_Perf_STRUCT and associated definitions. In preparation to remove IDS
headers, move the necessary definitions to AGESA.h.
BUG=b:112885948
TEST=Build grunt
Change-Id: I941a67a8889a9dbf35c9fd511c7f670623204134
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/28369
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Bayhub eMMC controller default runs SD base 50MHz at the first power on.
After boot into OS, mmc kernel driver will config controller to HS200/208MHz
and send MMC CMD21 (tuning block).
But Bayhub PCR register 0x3E4[22] (eMMC MODE select) is not clear
after system warm reset.
So eMMC will still run 208Mhz but there is no block tuning cmd in depthcharge.
It will cause two Sandisk eMMC (SDINBDA4-64G-V/SDINBDA4-32G-V) to fail to
load kernel and trap in 0x5B error (No bootable kernel found on disk).
BUG=b:111964336
BRANCH=master
TEST=emerge-grunt coreboot
Change-Id: Ic080682e67323577c7f0ba4ed08f8adafca620cc
Signed-off-by: Kevin Chiu <Kevin.Chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/28353
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change-Id: Ic238181d5c26ab8cf549137824a7c5e6c6d80ab1
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/28348
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
This change makes WIFI_SAR_CBFS user selectable option so that it can
be enabled/disabled from menuconfig along with the SAR filepath.
BUG=b:112425861
Change-Id: Idf6feaefe68e7ebf6786c2c36e92a054fba4483c
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/28352
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Change-Id: I0a704cba80d0439ae95db34a6b73df7be5b3b862
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/28290
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Currently, IDS_CALLOUT macros are only used in stoneyridge callout. In
preparation to remove IDS headers, move the definitions to AGESA.h.
BUG=b:112885948
TEST=Build grunt
Change-Id: Ia9717eb68fed2e568eaf169157c2837bb8232b7e
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/28297
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Fix formatting and missing close block quotes in nri_registers.md
Change-Id: I5fa0136f4d7f05737a0d53ff9da7d2c77b22d675
Signed-off-by: Tom Hiller <thrilleratplay@gmail.com>
Reviewed-on: https://review.coreboot.org/28327
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
Execute sphinx-autobuild for livesphinx make rule
Change-Id: I725392f1f132101eede8fed75e8d225c972ad1fe
Signed-off-by: Tom Hiller <thrilleratplay@gmail.com>
Reviewed-on: https://review.coreboot.org/28326
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
Reduce the CPU passive threshold sample rate from 5 seconds to 1
second so DPTF will react faster to rapid temperature increases.
Signed-off-by: Todd Broch <tbroch@chromium.org>
BUG=b:113101335
BRANCH=atlas
TEST=manual performance/power testing on nocturne.
No longer see messages like below in syslog,
'CPU0: Package temperature above threshold'
Change-Id: I2dc9d157b54500bae29e123978bb8ad6e05ef619
Reviewed-on: https://review.coreboot.org/28325
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Reduce the CPU passive threshold sample rate from 5 seconds to 1
second so DPTF will react faster to rapid temperature increases.
Signed-off-by: Todd Broch <tbroch@chromium.org>
BUG=b:67459049
BRANCH=nocturne
TEST=manual performance/power testing on nocturne.
No longer see messages like below in syslog,
'CPU3: Package temperature above threshold'
Change-Id: Ic20c718fd3a496db7c7192feec4f230d924cc458
Reviewed-on: https://review.coreboot.org/28324
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The macro IDS_ERROR_TRAP is only defined, and never used. Also,
IDSOPT_ERROR_TRAP_ENABLED is defined FALSE, so the macro would translate
to nothing. Remove the macro and IDSOPT_ERROR_TRAP_ENABLED.
BUG=b:112885948
TEST=Build grunt
Change-Id: I2c3ca4b0a4a1f96f245ba2f4902fd0051dda77ef
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/28296
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
Function IdsErrorStop() is only used within AmdLib.c function
LibAmdMsrRead(), which in turn is only used once within PspBaseLib.c and
three times inside AmdLib.c, all with well defined MSR addresses.
IdsErrorStop() is used as a trap if MSR address is 0 or 0xFFFFFFFF, which
clearly it's not. Therefore it can be safely removed from AmdLib.c.
BUG=b:112885948
TEST=Build grunt
Change-Id: I47ffcbd4fbae28b6d711a340f0ac3f3b007e8e4f
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/28295
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
Update TSR1 trip point from 48C to 50C.
Also, change power limit2 minimum value from 8W to 10W.
These are the values as per recent thermal tuning.
BUG=b:79779737
BRANCH=None
TEST=Build coreboot for Octopus board.
Change-Id: I33a9d2dc3e0e5566d95b1f1e46d3922dc8965b2b
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/28187
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Set NHLT version with get_acpi_revision(NHLT) to keep all table versions
in sync.
Change-Id: I4ea9d511142e4ea68e651e58c2c985e739c032d9
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/28279
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This commit fixes the values and thus fixes the issue of
audio device not getting detected on random reboots.
Change-Id: I34a4f62815d192005c3324d4f71b0aba377fe738
Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com>
Reviewed-on: https://review.coreboot.org/28280
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Daniel Kurtz <djkurtz@google.com>
|
|
Change-Id: Ie3ee4acfd272991133f02a56df6e23aa6071d3e9
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/27866
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Some unneeded includes are also removed.
Change-Id: Icd518c46d8503d11d24466c30840d7e514e9a05d
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/27865
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Use get_acpi_table_revision(HPET) to keep all table versions in sync.
Change-Id: Idb5e8ccd49ec27f87a290f33c62df3c177645669
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/28278
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Update the MADT table version to sync with the FADT table version.
All current coreboot FADT tables are set to ACPI_FADT_REV_ACPI_3_0
and the MADT should be set to match.
This error was found by running FWTS:
FAILED [MEDIUM] SPECMADTFADTRevisions: Test 2, MADT revision is not in sync with
the FADT revision; MADT 1 expects FADT 3.0 but found 4.0 instead.
BUG=b:112476331
TEST-Run FWTS
Change-Id: If5ef53794ff80dd21f13c247d17c2a0e9f9068f2
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/28256
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Most FADT report using ACPIv3 FADT table. Using the get revision
function keeps the table versions in sync.
Change-Id: Ie554faf1be65c7034dd0836f0029cdc79eae1aed
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/28277
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Use a single function to set ACPI table versions. This allows us
to keep revisions synced to the correct levels for coreboot. This
is a partial fix for the bug:
FAILED [MEDIUM] SPECMADTFADTRevisions: Test 2, MADT revision is not
in sync with the FADT revision; MADT 1 expects FADT 3.0 but found 4.0
instead.
BUG=b:112476331
TEST-Run FWTS
Change-Id: Ie9a486380e72b1754677c3cdf8190e3ceff9412b
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/28276
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Rename RSDP to RSDP_HEADER to match other AMD vendorcode and
to not pollute the namespace. We will use RSDP in a future patch.
Change-Id: I3b66135ae1732b86b5ebfcdc01a850a0d9d3eb50
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/28294
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
This patch disables the unused PCI clock outputs on the XIO2001 PCI
Express to PCI Bridge.
Change-Id: I0b9cf51a713f4ab46e71d250397486d136c26177
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/28284
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
add device "WCOM Digitizer" and "Synaptics Touchpad" for bobba
BUG=none
BRANCH=master
TEST=emerge-octopus coreboot
Change-Id: Ie0bf8ebab6d9cb9c8fe42a500efaa3d11ae359db
Signed-off-by: Pan Sheng-Liang <sheng-liang.pan@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/28332
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Change-Id: I53ddff302681737006f40ca8b79ec0735f1e6e45
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/28287
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Change-Id: I62fed1084efc3224c9563619d57fbdc5040ddbbc
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/28292
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Change-Id: I05ccb5a9a861fe44efec794aafe1805062543d53
Signed-off-by: Evgeny Zinoviev <me@ch1p.com>
Reviewed-on: https://review.coreboot.org/27776
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
According to the datasheet (rev. 1.6) there is no SP2 (apart from
some typos) and the IR is actually implemented as SP3 in LDN 0x16.
Additionally, there is LDN 0x15 to set up CIR-specific options of the
IR serial port, which was missing as well.
Change-Id: I34d90d8c44f11a4f62ccc4b836409cc443fb7952
Signed-off-by: Stefan Tauner <stefan.tauner@gmx.at>
Reviewed-on: https://review.coreboot.org/27856
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
TEST: same sha256sum with BUILD_TIMELESS=1.
Change-Id: Icf3368bcf1351f0e7cd4041c3792d76362aec9e5
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/28331
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
|
|
This reverts commit c5ee35ff861fe4447fd80119f645fba7bfd3a184.
Reason for revert: breaks boards, uncertain if it _really_ works.
Change-Id: I9ba2ba877b9a391306f89295c0c1d0e2d011c5ea
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/28338
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Jean Lucas <jean@4ray.co>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
To increase the lifetime of the circuit, it is necessary to reduce the
eMMC speed to DDR50 mode.
Change-Id: I40658b44a99e6600ed00950a1a177961f0055e7a
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/28283
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
The eMMC maximum speed is set to HS400 mode per default. To increase the
lifetime of the circuit, it is necessary to reduce the eMMC speed.
Change-Id: I6fa5eb56a0593e24269ef143645c506232879889
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/28282
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
* Add VERSTAGE and VBOOT_WORK to memlayout.
* Add hard and soft reset.
* Add missing makefile and kconfig includes.
Change-Id: I0d7e3c220f5c2c50c4ffe59ac929cb865bfac0ad
Signed-off-by: Philipp Deppenwiese <zaolin@das-labor.org>
Reviewed-on: https://review.coreboot.org/28022
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
As preparation to constify devicetree data, do it the right way.
Change-Id: I5081de020bb73c56aa8bdf7bb17fe6b2913d0ffe
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/28266
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
|
|
* Add const quailifier to arguments and elements.
* Add casts where necessary in cn81xx/soc.
Tested on Cavium CN81xx EVB SFF.
Change-Id: Id27966427fb97457fe883be32685d1397fb0781f
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/28267
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Since ifdfake has been deprecated in favor of better alternatives, there
is no need to support it any further. Remove it from the build system.
Change-Id: Id62e95ba72004a1e15453e3eb75f09cb8194feb2
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/28233
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Since ifdfake has been deprecated in favor of better alternatives, there
is no need to support it any further. Remove it from "util/", as well as
any leftover references in other files.
Change-Id: I45fe3d9fd606a61d5c3b9d0e6489a1df6d6510f0
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/28234
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Will be used by the APIC.
BUG=b:109749762
TEST=Verified by the other cls in the stack.
Change-Id: Id86f2719d98a90318ac625e09601e5dbb06e3765
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Reviewed-on: https://review.coreboot.org/28239
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Since libpayload doesn't link against libgcc we need to define our own
cpuid macro. I didn't add any error checking since anything in the last
decade should support cpuid.
BUG=b:109749762
TEST=called it and made sure the correct flags were returned.
Change-Id: Id09878ac80c74416d0abca83e217516a9c1afeff
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Reviewed-on: https://review.coreboot.org/28238
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
With Alpine base, use pip to install Sphinx 1.7 and Sphinx-autobuild
Alpine, a 4.5MB base, is used over Debian Stable, 101MB, to cut down the
total size of the docker image.
Change-Id: I53f246206458b1de34cd7f3a42481b91ca285ff0
Signed-off-by: Tom Hiller <thrilleratplay@gmail.com>
Reviewed-on: https://review.coreboot.org/28211
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Add livesphinx to start sphinx-autobuild
Change-Id: I9eb3217e758c2c882c759fa7ae75a39aaf1a0358
Signed-off-by: Tom Hiller <thrilleratplay@gmail.com>
Reviewed-on: https://review.coreboot.org/28210
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
This enables CBAS device on Nocturne to allow hid-google-whisker driver
in kernel properly detect device configuration.
Change-Id: I5905a2de208e94062f2768a9b7d22147f85c7f38
Signed-off-by: Dmitry Torokhov <dtor@chromium.org>
Reviewed-on: https://review.coreboot.org/28262
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
On some detachables, the mere presence of attached base is not enough to
determine whether the device is in tablet mode or not, so we introducing
a new "switch" in EC, separate from "Tablet Mode" switch, to signal
whether the base is attached or not.
We also want the driver to be separate from cros_ec_keyb, so we create
a new ACPI device, C(hrome)B(ase)A(ttached)S(witch), with HID GOOG000B,
and guard it with EC_ENABLE_CBAS_DEVICE.
Change-Id: Id73a12f04a1a48f7fbd9365c2a501afadf3878fa
Signed-off-by: Dmitry Torokhov <dtor@chromium.org>
Reviewed-on: https://review.coreboot.org/28260
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
For the 1st redesign of mc_apl1 mainboard some adjustments are
necessary:
- The FPGA is now connected directly via a PCIe Root Port
- Internal Apollo Lake UARTs are now used
- Adjusting GPIO settings
Change-Id: I8917a52325306f24d1c39a88dac47b0cee760d57
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/28270
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
A FPGA is not necessarily available in further mc_apl1 variants. So we
move the loading of the driver and the notify function to the mc_apl1
variant.
Setting the CPU to Max Non-Turbo Ratio is also not absolutely necessary
for further variants.
Change-Id: I9f8438407f231df08e1ad04655bb6f747257e268
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/28269
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
This supports the Foxconn d41s, d42s, d51s, d52s.
The following is tested (SeaBIOS 1.12 + Linux 4.9) and works:
- COM1
- S3 resume (with SeaBIOS needs sercon disabled)
- Native graphic init on VGA output
- SATA
- USB
- Ethernet
- PS2 keyboard
The base for this mainboard port was the Intel D510MO port.
Change-Id: Ie4ec9cbf70adcdddbc2e5d805e4806825c320072
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/28227
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
src/mainboard/google/octopus/mainboard.c
Function dev_find_slot may return NULL,
check before its usage.
Found-by: klockwork
BRANCH=None
TEST=Built & booted Yorp board.
Change-Id: I160adbe3b0a5a2b0f11fd1567513860664d4bee3
Signed-off-by: John Zhao <john.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/28235
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This open-codes flash_cmd, but until the API is fixed for real, it uses
xfer's existing scatter-gather ability to write command and data in one
go.
BUG=chromium:446201
TEST=emerge-coral coreboot succeeds
Change-Id: Ic81b7c9f7e0f2647e59b81d61abd68d36051e578
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/28254
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
The change updates GPIO configuration for meep.
1. Update touchscreen power enable GPIO in devicetree.
2. Provide default override tables for GPIO configuration.
BUG=b:112955087
TEST=Boot on meep proto board with Intel (Jefferson Peak) wifi card.
Change-Id: Idb4e7a510eef15c2e118058d5848080782f4f665
Signed-off-by: Wisley Chen <wisley.chen@quantatw.com>
Reviewed-on: https://review.coreboot.org/28252
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Writes to VGA MEM and IO by NGI are invalid if the IGD is not decoding
them.
Change-Id: I4b9329d14105eb563a0d4aea6ef75ff11febf6df
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/27984
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
src/soc/intel/apollolake/chip.c
Apply bitwise operator instead of logical one.
Found-by: Coverity Scan
BRANCH=None
TEST=Built & booted Yorp board.
Change-Id: I36746b04dec889f53c8d7eeb3b1d8118eff1de42
Signed-off-by: John Zhao <john.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/28261
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Since ifdfake has been deprecated in favor of better alternatives, such
as flashrom IFD parsing. Therefore, there is no need to support ifdfake
any further. Remove the IFD_*_REGION values on the few motherboards with
them.
Change-Id: Ie07116a7fb960c6ca832d802016f22c6677baac9
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/28232
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
There's a small window of opportunity when CPU is already in SMM but has
not yet entered S3 for a wake event to happen, which would cause a failed
S3 entry. Check for pending events at the very last moment possible, and
if there are pending wake events report them.
BUG=b:111100312
TEST=build and boot grunt.
Change-Id: I9472fdf481897fcf9f4c669f6b1514ef479fce7a
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/28247
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
For debug reasons, sometimes you not only want to log an event, but also
some extra information that would help debugging. Create an extended event
reporting event type with a dword complement, and define extended events
for failing to enter S3 due to pending wake event (one for pm1 and one for
gpe0).
BUG=b:111100312
TEST=Add a fake pending wake event, build and boot grunt, see the event in
eventlog.txt.
Change-Id: I3e8df0953db09197d6d8145b0fc1e583379deaa5
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/28246
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Because the Kconfig configuration files for primary payloads are
already sourced via a wildcard pattern this change requires to
use another file name pattern.
Change-Id: I83b89f5e14618e8a487ebb044fcdd3c175662591
Signed-off-by: Stefan Tauner <stefan.tauner@gmx.at>
Reviewed-on: https://review.coreboot.org/28217
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Since we can derive chromeos_acpi's location from that of
ACPI GNVS, remove chromeos_acpi entry from cbtable and
instead use acpi_gnvs + GVNS_CHROMEOS_ACPI_OFFSET.
BUG=b:112288216
TEST=None
CQ-DEPEND=CL:1179725
Change-Id: I74d8a9965a0ed7874ff03884e7a921fd725eace9
Signed-off-by: Joel Kitching <kitching@google.com>
Reviewed-on: https://review.coreboot.org/28190
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Since we can retrieve the address of ACPI GNVS directly
from CBMEM_ID_ACPI_GNVS, there is no need to store and
update a pointer separately.
TEST=Compile and run on Eve
Signed-off-by: Joel Kitching <kitching@google.com>
Change-Id: I59f3d0547a4a724e66617c791ad82c9f504cadea
Reviewed-on: https://review.coreboot.org/28189
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Change-Id: Idce2587a87c5e0677a4571b59ef40e5486c22da9
Signed-off-by: Martin Roth <gaumless@gmail.com>
Reviewed-on: https://review.coreboot.org/27527
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Copy code of depthcharge boot/coreboot.c and adapt it.
Tested on Cavium CN8100 EVB SFF, /sys/firmware/log is readable
and prints the log.
Change-Id: Ib714a021a24f51407558f484cd97aa58ecd43977
Signed-off-by: Philipp Deppenwiese <zaolin@das-labor.org>
Reviewed-on: https://review.coreboot.org/28104
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Fix some words' spelling and rename "Sandybridge" and "Ivybridge" in
text (not filepaths) to match Intel's names "Sandy Bridge" and "Ivy
Bridge".
Change-Id: Ic77126ccaf1d3ec5530a35d1a0f7d2ea5e174c9a
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/28231
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
This change updates the board id check for version >=2 to apply new
GPIO configs.
BUG=b:112618194
Change-Id: I3544c9596c465615818d2040682e554a64fc6b1a
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/28263
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
There's nothing Sandy Bridge specific in this code.
Make it available on all platforms to reduce code duplication.
Tested on Lenovo T430: SMBIOS entry 17 is still valid.
Change-Id: I051c3e07a999d8dad082c24f65b43dce180349fd
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/28213
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Alexander Couzens <lynxis@fe80.eu>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
* Fix ACPI resume path compilation for TPM ramstage
driver
* Move enabling of the TPM prior activation and remove
reboot return status from TPM enable.
More information can be found via the TCG
specification v1.2
Tested=Elgon
Change-Id: Ided110e0c1889b302e29acac6d8d2341f97eb10b
Signed-off-by: Philipp Deppenwiese <zaolin@das-labor.org>
Reviewed-on: https://review.coreboot.org/28085
Reviewed-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I074d57fa5b140b6946ae81beb210fefac48a66eb
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/28226
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
There is no public datasheet available for this SuperIO so the resources are
guessed by looking at other ITE SuperIO's and the register dumps while running
vendor firmware.
The only board with this SuperIO in the tree is the asus m5a88-v. Most of the
devicetree entries would have been invalid here so one should not worry too much
about regressions.
Tested with Foxconn d41s.
Change-Id: I6715c68b3aa9aebf6e292975cbf64ce905b30e8b
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/28225
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
This should not be board specific.
Change-Id: Ifa617e84af767f33a94f1ddfa7d4883c1a45198f
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/28224
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
When doing the receive enable training, the final mapping of the ranks is
already done, so we can be sure that that address 0x00000000 there will always
be a rank.
Change-Id: I7ac017a8816fc9a47cef0695826a1c32f699f6f8
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/28230
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
With this the time spend during the raminit decreases from ~480ms to ~126ms.
Change-Id: Ic23f39f1017010c89795e626f6a6f918f8bda17a
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/28229
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Some OS certification test (for example Windows) will fail if there
are unsupported sleep states. Since these states are not really used
today, we can remove them from ACPI table.
BRANCH=eve
BUG=b:72197653
TEST=certification system sleep test pass.
Change-Id: I5f5122cac1bf61f7c580afb18cc66b5ff07286fb
Signed-off-by: Lucas Chen <lucas.chen@quanta.corp-partner.google.com>
Reviewed-on: https://chromium-review.googlesource.com/1065401
Commit-Queue: David Wu <david_wu@quanta.corp-partner.google.com>
Tested-by: David Wu <david_wu@quanta.corp-partner.google.com>
Reviewed-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: https://review.coreboot.org/28080
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
The only code still used are LibAmdPciRead() and LibAmdPciWrite(). These
functions are used by PspBaseLib. Remove all functions that are not used,
directly or indirectly, by LibAmdPciRead() and LibAmdPciWrite().
BUG=b:112688270
TEST=Build grunt
Change-Id: Iba5cfbeee8e83ca78279a1bc2a333370c04f55ed
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/28194
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This small change is required for the successful loading of microcode
from F15TnMicrocodePatch0600110F_Enc.c for the Richland RL-A1 CPUs,
such as A10-5750M found at coreboot-supported Lenovo G505S laptop.
Richland RL-A1 and Trinity TN-A1 CPUs are using the same microcode,
so the Richland RL-A1 IDs should be added to this equivalence table.
Function `GetPatchEquivalentId()` in
`src/vendorcode/amd/agesa/f15tn/Proc/CPU/cpuMicrocodePatch.c`
goes through the equivalence table like below.
for (i = 0; i < (EquivalencyEntries * 2); i += 2) {
// check for equivalence
if (ProcessorRevisionId == MicrocodeEquivalenceTable[i]) {
*ProcessorEquivalentId = MicrocodeEquivalenceTable[i + 1];
return (TRUE);
}
}
Change-Id: I7a68f2fef74fb4c578c47645f727a9ed45526f69
Signed-off-by: Mike Banon <mikebdp2@gmail.com>
Reviewed-on: https://review.coreboot.org/28204
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: <awokd@danwin1210.me>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change PL1 from 4.5W to 7W, based on thermal test results.
BRANCH=eve
BUG=b:73133864
TEST=Verify the MSR PL1 limitation is set to 7W.
Change-Id: Ic3629f9c3b7eb6eef1a1b5a3051c9a11448bc9ad
Signed-off-by: Lucas Chen <lucas.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/28078
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
In legacy mode, DPTF on some systems may rely on MMIO to control PL1
settings. However, MSR PL1 also contributes to the decision of max
PL1 power; and in the current design, the lower value takes effect.
In order to align MMIO and MSR settings, a tdp_pl1_override option is
added to override the MSR PL1 limitation.
BRANCH=eve
BUG=b:73133864
TEST=1. Write PL1 override setting in devicetree.cb
2. Verify the MSR PL1 limitation is set correctly.
Change-Id: I35b8747ad3ee4c68c30d49a9436aa319360bab9b
Signed-off-by: Lucas Chen <lucas.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/28079
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
There were so many pitfalls that I wrote my own version of this even-
tually. This version is inspired by the procedure of Alex Thiessen[1].
Instead of generating a `build.h` on demand, we always generate a tem-
porary version that, if it differs from the current one, is added as
a dependency.
As we use .SECONDEXPANSION on the prerequisites, special care is taken
that we won't generate the file twice. As it would be too late to add
the dependency if we'd run `genbuild_h.sh` inside a recipe, we have
to run it through the `$(shell)` function. But that brings us to the
next issue: The make variables used by `genbuild_h.sh` are not expor-
ted to this shell like they would be in a recipe. So we export them
manually. We could also make these variables explicit parameters of
`genbuild_h.sh` instead.
An alternative to always creating the temporary `build.h` would be
to add a phony target as dependency instead, and finally calling
`genbuild_h.sh` again in case we need an update. But, um, we create
so many files anyway...
[1] https://review.coreboot.org/25685
Change-Id: I311cf610eabae873c70f2985fc7a09acec8061f0
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/28197
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
This adds support for controlling the keyboard backlight over ACPI.
BUG=b:112619894
BRANCH=none
TEST=verified keyboard backlight can be adjusted using keyboard
shortcuts
Change-Id: I25713f341e8b5a4e50903ac109bfa717f20969d8
Signed-off-by: Caveh Jalali <caveh@chromium.org>
Reviewed-on: https://review.coreboot.org/28205
Reviewed-by: Caveh Jalali <caveh@google.com>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable Enhanced Intel SpeedStep (EIST) on nocturne.
Change-Id: Ie9b832f5bc3a5ef300783bd9bcd7cf5d186b98fa
Signed-off-by: Matt Delco <delco@chromium.org>
Reviewed-on: https://review.coreboot.org/28103
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Enable Enhanced Intel SpeedStep (EIST) on eve.
Change-Id: I49b18b817cda570f5c3c4d048c4e03329ac10b87
Signed-off-by: Matt Delco <delco@chromium.org>
Reviewed-on: https://review.coreboot.org/28102
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
ACPI 5.0 defines a method _CPC for "Continuous Performance Control" (CPPC).
Linux has a driver that enables features like speed shift without
consulting ACPI. Other OSes instead rely on this information and need a
_CPC present. Prior to this change performance in Win10 never exceeds
80% and MSR 0x770 is 0, while with this change (and enabling eist) higher
speeds can be achieved and the MSR value is now 1.
Change-Id: Ib7e0ae13f4b664b51e42f963e53c71f8832be062
Signed-off-by: Matt Delco <delco@chromium.org>
Reviewed-on: https://review.coreboot.org/27673
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
This change adds a method to init a cppc_config structure in a way that
should ideally work across Intel processors that support EIST.
Change-Id: Ib767df63d796bd1f21e36bcf575cf912e09090a1
Signed-off-by: Matt Delco <delco@chromium.org>
Reviewed-on: https://review.coreboot.org/28068
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
This patch moves uart functions which are common across multiple soc to
block/uart. This will remove redundant code copy from soc
{skylake/apollolake/cannonlake}.
BUG=b:78109109
BRANCH=none
TEST=Build and boot on KBL/APL/CNL platform.
Change-Id: I109d0e5c942e499cb763bde47cb7d53dfbf5cef6
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/26164
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This is meant to solve an issue where the proximity sensor may fluctuate
between CLOSE / FAR in rapid succession upon the user removing their hand
from the unit, before settling on the correct output.
Using the hardware debouncing filter solves this issue and removes the
spurious fluctuations.
BRANCH=None
BUG=None
TEST=manual on Nocturne, observing events come in
Change-Id: I78cc4852d42fcda6209fedce1ce91236b5814571
Signed-off-by: Enrico Granata <egranata@chromium.org>
Reviewed-on: https://review.coreboot.org/28112
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
There are two SKUs of Whiskey Lake W0, 2-core and 4-core.
Change-Id: Ia9b2707568702a5fbae3e9495ca53df34613a542
Signed-off-by: Krzysztof Sywula <krzysztof.m.sywula@intel.com>
Reviewed-on: https://review.coreboot.org/28111
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
When USB OTG is set, GLK FSP enables xHCI SW ID pin and configures
USB-C as device mode. Force USB-C into host mode.
BUG=b:111623911
TEST=Verified that USB-C being host mode once USB OTG is set.
Change-Id: Iaca3d25a1159f922b743963cbc508d8defa7b6ff
Signed-off-by: John Zhao <john.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/27746
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Weida touchscreen controller needs 130 ms delay after reset
BUG=b:111102092
BRANCH=master
TEST=Verify touchscreen on fleex works with this change
Change-Id: Ia86c3acf3c0e09ca05cc1681113672b546f830a0
Signed-off-by: Crystal Lin <crystal_lin@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/28115
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
`superiotool` follows its own style (e.g. lot's of missing spaces
and odd placement of braces in the register descriptions).
Change-Id: Ifa33938a0fbac10577cbda10537f856f6f100233
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/28214
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I2075142a0b241222839899e707a1e3d264746432
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/28228
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
|
|
Callers should have a default ready and get noticed by the return
value of get_option(). No need to scare log readers at this location.
Change-Id: Ied373d8a02afdc8d1017c9f41d9004e3797dfbb3
Signed-off-by: Stefan Tauner <stefan.tauner@gmx.at>
Reviewed-on: https://review.coreboot.org/28215
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: Ic6e7341b53bcabc415089ccfab121d3694ccb071
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/28212
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
The DIMM type read from SPD needs to be converted to make sure SMBIOS fills
in the correct formfactor.
Tested on Lenovo T430: The Form Factor no longer reads as unknown.
Change-Id: Ia0211fa133f4ba9d60dfbd5f0dd45a43df68c030
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/28192
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Fill in SMBIOS type 17 DIMM serial number, read from SPD.
Fixes FWTS SMBIOS type 17 test.
Change-Id: Id6e818bfdf4af0fd34af56dc23df052a3f8c348d
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/28191
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
src/soc/intel/common/block/cpu/mp_init.c
Function init_cpus: Pointer dev checked for NULL may be
dereferenced.
src/soc/intel/common/block/graphics/graphics.c
Function graphics_get_bar: Pointer dev returned from
call may be NULL and will be dereferenced.
BRANCH=None
TEST=Built & booted Yorp board.
Change-Id: I5e7caa15a3911e05ff346d338493673af5318a51
Signed-off-by: John Zhao <john.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/28060
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Change-Id: I4b0577bf3c00307733a1096749c1835d86764f29
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/27867
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Change-Id: Ib5799cceacefa89385a7615ef1c4b4d06157044f
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/27868
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Make the code simpler and improve readability.
Change-Id: Ifa9308c32e4646c122254931b55fb83541a10a3c
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Reviewed-on: https://review.coreboot.org/28195
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
The help text is already very clear but some users (first and
foremost the author of this patch ;) are still selecting
USBDEBUG_DONGLE_BEAGLEBONE when using a BeagleBone Black and
waste hours on analyzing the debug output of EHCI debug driver.
Change-Id: Ibf002db7d81ed44878f3ce0324170e4b99e780a5
Signed-off-by: Stefan Tauner <stefan.tauner@gmx.at>
Reviewed-on: https://review.coreboot.org/28184
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Fix scope of ResourceSource, which should match the scope of the
device itself.
Change-Id: I9d0ff0ecc2721ec55b1ed12dddb495cd55966daf
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/28114
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
All different memory configuration should be supported by now.
Thanks to Igor Lee.
Change-Id: Ib93c0e3cbdc29cbf6cff26292df4fbbb8208082f
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Tested-by: Igor Lee <getrun@gmail.com>
Reviewed-on: https://review.coreboot.org/27781
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
