Age | Commit message (Collapse) | Author |
|
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6085 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Updated patch with improved comments and small bugfix (use same
value for min and max on io resource).
While adding the area between TOM1 and 4GB to \SB.PCI0._CRS seems to be the
easiest way to get both Linux and Windows happy, it is not quite correct
because reserved areas like APIC, MMCONF etc. ranges need to be excluded.
This is a proof of concept patch for the M2V board that dynamically creates a
ResourceTemplate() containing these in the SSDT and adds a corresponding
PNP0C02 device to the DSDT.
All resources that have IORESOURCE_RESERVE and (IORESOURCE_MEM or IORESOURCE_IO) set
are added.
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Added M2V-MX SE too.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Rudolf Marek <r.marek@assembler.cz>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6084 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
as an ACPI motherboard resource or it will not enable MMCONFIG
and the extended pcie configuration area will be unaccessible:
This patch adds the IORESOURCE_RESERVE flag to the APIC and MMCONF
resource flags to do this.
I also added a new resource for the mapped bios rom area just below 4GB.
I'm not sure if the choice for the index parameter of new_resource()
is correct though.
Note that the bios rom decode is enabled in
src/southbridge/via/vt8237r/vt8237r_early_smbus.c
for the whole 4MB area (even though the comment says 1MB).
Ruik: I extended the flash range to 16MB (This is what VT8237S can decode)
Remove the MMCONFIG region reserve in the mainboard file (this patch makes it obsolete)
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Acked-by: Rudolf Marek <r.marek@assembler.cz>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6083 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
http://tracker.coreboot.org/trac/coreboot/changeset/3953
Note that all corresponding DSDTs only ever check TOM2 against 0.
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Acked-by: Rudolf Marek <r.marek@assembler.cz>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6082 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
CONFIG_PIRQ_ROUTE) so far is the amd cs5530.
Add one for vt8237 too.
Setting up the pci routing is important in case you want to boot DOS,
OSes that don't support ACPI or MP tables and ROMs for add-in storage
controllers may depend on this too.
TODO: Fix the 4 routing links limitation in
src/arch/i386/boot/pirq_routing.c
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Acked-by: Rudolf Marek <r.marek@assembler.cz>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6081 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
The only difference is that the "G" version is in a Pb-free package, which
is not relevant from a programmer's view.
We keep W83627THG (and drop W83627THF) because:
- The W83627THF had a CIR device / LDN which doesn't actually exist.
- The W83627THF had no GPIO2, GPIO3 LDNs (were commented out).
- The W83627THF didn't use the PNP_MSC0/1 which is needed/used by boards.
This also fixes an issue on MSI MS7135's devicetree.cb:
device pnp 4e.6 off end # XXX keep allocator happy
The line above can be (and is) removed, as it was only needed due to the
incorrect CIR LDN in the W83627THF.
In the iwill/dk8x target: Drop incorrect LDNs 4 and 6, add 0xb.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6080 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6079 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6078 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
make their defaults more obvious.
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Acked-by: Stefan Reinauer <stepan@coreboot.org>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6077 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6076 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6075 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6074 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
- Random coding style, whitespace and cosmetic fixes.
- Consistently use the same spacing and 4-hexdigit port number format
in the pnp_dev_info[] arrays.
- Drop dead/unused code and less useful comments.
- Add missing "(C)" characters and copyright years.
- Shorten and simplify some code snippets.
- Use u8/u16/etc. everywhere.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6073 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
For now this is a plain copy of the ASUS A8V-E SE target, I reported
that most of the code also works (sort of) for the ASUS A8V-E Deluxe
a long while ago, see
http://www.coreboot.org/pipermail/coreboot/2008-March/031866.html
http://www.coreboot.org/ASUS_A8V-E_Deluxe
There will be a bunch of changes necessary though (devicetree.cb, mptable.c,
ACPI, etc) which do not apply to the A8V-E SE, so we need an extra target.
Also: Increase ID_SECTION_OFFSET on the VIA K8T890/K8M890 southbridge, as
otherwise there will be build errors if the MAINBOARD_PART_NUMBER string
gets too long (as is the case for "A8V-E Deluxe"). The error is:
ld: section .id loaded at [00000000ffffffd2,00000000ffffffef] overlaps
section .romstrap loaded at [00000000ffffff80,00000000ffffffd3]
(both with stock Debian gcc and with xgcc)
Increase ID_SECTION_OFFSET (default 0x10) to 0x80 as other southbridges do.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6072 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Add a few more comments for the entries, and also change the devicetree.cb
files to the more compact and better readable variant with indentation level
of 2 spaces (instead of random mix of tabs and spaces).
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6071 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Rudolf Marek <r.marek@assembler.cz>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6070 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
an override function in m2v/mainboard.c
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Acked-by: Rudolf Marek <r.marek@assembler.cz>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6069 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
cablesel |= (sb->ide0_80pin_cable << 28) |
(sb->ide0_80pin_cable << 20) |
(sb->ide1_80pin_cable << 12) |
(sb->ide1_80pin_cable << 4);
in vt8237r_ide.c ends up doing
cablesel |= 0xfffffff0;
(with both bits set to 1) which is probably not the intended result. ;)
After a short discussion on irc the consensus was to change the
bitfields to u8 as it's probably not worth it using bitfields here.
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Acked-by: Rudolf Marek <r.marek@assembler.cz>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6068 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
-- When building for UMA, reduce the limit for DRAM below 4GB
from E0000000 to C0000000. This is needed to accomodate the
UMA frame buffer.
-- Correct problem where msr C0010010 bits 21 and 22 (MtrrTom2En
and Tom2ForceMemTypeWB) are not set consistently across cores.
-- Enable TOM2 only if DRAM is present above 4GB.
-- Use AMD Tom2ForceMemTypeWB feature to avoid the need for
variable MTRR ranges above 4GB.
-- Add above4gb flag argument to function x86_setup_var_mtrrs. Clearing
this flag causes x86_setup_var_mtrrs() to omit MTRR ranges for
DRAM above 4GB. AMD systems use this option to conserve MTRRs.
-- Northbridge.c change to deduct UMA memory from DRAM size reported
by ram_resource. This corrects a problem where mtrr.c generates an
unexpected variable MTRR range.
-- Correct problem causing build failure when CONFIG_GFXUMA=1 and
CONFIG_VAR_MTRR_HOLE=0.
-- Reserve the UMA DRAM range for AMD K8 as is already done for AMD
family 10h.
Tested with mahogany on ECS A780G-GM with 2GB and 4GB.
Tested with mahogany_fam10 on ECS A780G-GM with 2GB and 4GB.
Signed-off-by: Scott Duplichan <scott@notabs.org>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6067 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
The power-on default is 1.95V, set the DDR2 voltage to
standards-conforming 1.8V.
I also measured with a multimeter to confirm this.
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6066 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
This isn't hooked up anywhere, so won't affect anything, except for
developers trying to remove configuration #defines.
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6065 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Jonathan Kollasch <jakllsch@kollasch.net>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6064 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
The pc_keyboard_init() function no longer takes any base addresses
since r5152 (passed in via res0/res1 variables previously), so drop them.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6063 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
I missed this one since it was working anyway, since
"The LPC BIOS ROM is always accessed when ISA addresses
FFF80000-FFFFFFFF and 000F0000-000FFFFF are decoded" (VT8237R datasheet)
And the rom I use for testing is smaller than this 512KB default range.
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6062 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Needed to change class from raid to ide so seabios can boot from it.
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6061 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6060 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6059 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
- i3100_early_serial.c:
- Split out enter/exit functions as the other Super I/Os do.
- Make i3100_enable_serial() take a device_t as usual, and convert
it to use the standard pnp_* function instead of open-coding
the same functionality by hand.
- Factor out i3100_configure_uart_clk() from i3100_enable_serial(),
we do the same in various other Super I/Os, e.g. ITE ones.
- Add some #defines for register / bit values and some comments.
- Only functional change: Don't set bit 1 of SIW_CONFIGURATION, it's
marked as "READ ONLY, WRITES IGNORED" in the datasheet.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6058 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
- Whitespace, coding style, and typo fixes.
- Drop unused/obsolete "#config chip.h".
- Use u8/u16/etc. everywhere.
- Use pnp_read_config()/pnp_write_config() instead of open-coding them.
- Use pnp_set_logical_device() instead of open-coding it.
- W83627EHG: Fix incorrect enable_hwm_smbus() code comment.
- Use ARRAY_SIZE.
- w83627hf/superio.c: w83627hf_16_bit_addr_qual(): Bugfix, the code was using
'dev->path.pnp.port >> 8' as config port, which is incorrect in superio.c
(which has a "real" device_t struct, in contrast to *_early_serial.c which
uses "unsigned" as device_t where 'dev >> 8' is required).
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6057 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
The function is called with no format specifiers in the first parameter
throughout the code, so it needs to work also with just one parameter.
Signed-off-by: Peter Stuge <peter@stuge.se>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6056 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Peter Stuge <peter@stuge.se>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6055 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
- Hook up malloc() debug code via CONFIG_DEBUG_MALLOC. Only show it in
menuconfig if at least DEBUG or SPEW are selected as loglevel, as this
code does additional printk(BIOS_DEBUG, ...) calls which would otherwise
not be visible anyway.
- Similarly, make DEBUG_CAR and REALMODE_DEBUG only visible if thr DEBUG or
SPEW loglevel is selected.
- Get rid of a custom "debug" macro, use printk() as usual.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6054 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
- it8661f_enable_serial() is now in the usual format, using pnp_* functions.
- Factor out pnp_enter_ext_func_mode()/pnp_exit_ext_func_mode().
- Factor out it8661f_set_clkin() to set the CLKIN to 24/48MHz.
- Factor out it8661f_enable_logical_devices(), might not be needed though.
We leave it here until it's confirmed on hardware that it's not needed.
- Move some #defines to it8661f.h.
- Drop no longer used it8661f_sio_write().
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6053 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Linux kernel, which was previously complaining that the MTRR setup
is wrong, if the cpu supports more than CONFIG_CPU_ADDR_BITS bits of
address space.
Shamelessly copied from Linux arch/x86/kernel/cpu/mtrr/main.c
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Acked-by: Scott Duplichan <scott@notabs.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6052 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Acked-by: Rudolf Marek <r.marek@assembler.cz>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6051 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Acked-by: Rudolf Marek <r.marek@assembler.cz>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6050 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6049 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
This patch fixes a hang on
supermicro/h8dme
supermicro/h8dmr
supermicro/h8dmr_fam10
and possibly on other mcp55-based boards.
Signed-off-by: Ward Vandewege <ward@gnu.org>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6048 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
- Drop some of the less useful / outdated / duplicated comments.
- Simplify and streamline some code to look like the other Super I/Os.
- Use u8/16/etc. everywhere.
- ITE IT8718F: Add missing GPIO LDN.
- Add missing braces around SIO_DATA #defines, potential bug even.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6047 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
compatible. The extended cmos is accessed differently for AMD
and Intel RTCs. Not sure what if any OS cares about this distinction,
but non-Intel compatible seems like a safer way to report the AMD RTC.
Tested with Win7 on Mahogany_fam10 and kino-780am2-fam10.
Signed-off-by: Scott Duplichan <scott@notabs.org>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6046 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
This adds the m2v directory and necessary files to src/mainboards/asus and
adjusts the Kconfig.
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Acked-by: Rudolf Marek <r.marek@assembler.cz>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6045 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
adjusts the Kconfig.
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Acked-by: Rudolf Marek <r.marek@assembler.cz>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6044 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
"Use get_vt8237_lpc() in vt8237_sb_enable_fid_vid()" patches.
This adds VT8237A specific VLINK/LPC init in vt8237r_early_smbus.c
I ran some tests and apparently both the
| /* So the chip knows we are on AMD. */
| pci_write_config8(devctl, 0x7c, 0x7f);
and
| /*
| * Allow SLP# signal to assert LDTSTOP_L.
| * Will work for C3 and for FID/VID change.
| */
| outb(0x1, VT8237R_ACPI_IO_BASE + 0x11);
in vt8237r_early_smbus.c are needed on VT8237A, otherwise I get a (non-fatal)
fid/vid change error on boot.
While vt8237a_vlink_init() in vt8237_ctrl.c is a modified vt8237r_vlink_init(),
vt8237a_init() in vt8237r_lpc.c is a modified vt8237s_init().
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Acked-by: Rudolf Marek <r.marek@assembler.cz>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6043 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Depends on the "Introduce get_vt8237_lpc() function" patch.
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Acked-by: Rudolf Marek <r.marek@assembler.cz>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6042 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
I broke this out into a seperate part to keep the other half as
straight-forward as possible.
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Acked-by: Rudolf Marek <r.marek@assembler.cz>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6041 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
add a get_vt8237_lpc() function.
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Acked-by: Rudolf Marek <r.marek@assembler.cz>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6040 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
http://linux.via.com.tw/ as VX800 seems to be compatible.
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Acked-by: Rudolf Marek <r.marek@assembler.cz>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6039 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
and vt8237r_lpc.c.
While vt8237a_vlink_init() in vt8237_ctrl.c is a modified vt8237r_vlink_init(),
vt8237a_init() in vt8237r_lpc.c is a modified vt8237s_init().
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Acked-by: Rudolf Marek <r.marek@assembler.cz>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6038 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Rudolf
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Rudolf Marek <r.marek@assembler.cz>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6037 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6036 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
vt8237r_lpc.c
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Acked-by: Rudolf Marek <r.marek@assembler.cz>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6035 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
other place, and that defines these symbols itself (and
identical, too). Drop them.
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6034 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6033 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6032 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
All other uses of these symbols have their own (identical)
definitions.
abuild-tested and trivial
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6031 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
- VIA VT1211:
- Add missing LDNs and respective code to handle them.
- Add some TODOs for other stuff that needs fixing.
- Use VT1211_SP1 instead of hardcoding the LDN number (2).
- Fixup pnp_dev_info[] as per datasheet, but some TODOs remain.
- Various coding style fixes and changes to u8/u16/etc.
- Serverengines Pilot: Various coding style fixes and changes to u8/u16/etc.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6030 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6029 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Acked-by: Myles Watson <mylesgw@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6028 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
- Use HAVE_ACPI_TABLES, HAVE_MP_TABLE, and HAVE_PIRQ_TABLE (instead of
GENERATE_*) in the board's Kconfig file, as all other boards do.
- Add missing HAVE_ACPI_TABLES/HAVE_MP_TABLE/HAVE_PIRQ_TABLE to boards
which have the respective files. The only exception: EPIA-M700 doesn't
select ACPI, as it doesn't have dsdt.asl. Added a comment that the user
is supposed to run the 'get_dsdt' script and edit Kconfig afterwards.
- Fix minor warning/error in
src/mainboard/msi/ms9652_fam10/acpi_tables.c,
now that the file is actually used.
- msi/ms9652_fam10: use #include instead of Include() as we usually do
now.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6027 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6026 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
"To enable configuration, the entry key 0x87 must be written to
the index port"
"
-o 4e 87
-o 4e 87 (enable configuration)
-o 4e aa (disable configuration)
"
This piece of text appears in most of the datasheet of fintek superio.
It doesnt say it quite clear, but it seems that the 0x87 should
be written twice. I tried on f81865, which is not in the coreboot tree
yet. If the 0x87 is only written once, you can only R/W the index/data
port once. All the subsequent RW will fail. Writing twice will be ok.
Plus, in the superiotool, the function enter_conf_mode_winbond_fintek_ite_8787
also write 8787.
The fintek superio chips seem to enable the UART automatically when the
power is on. So I didnt find it failed to access.
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6025 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6024 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
This is Abuild and boot tested.
Signed-off-by: Nils Jacobs <njacobs8@hetnet.nl>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6023 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
This is Abuild and boot tested.
Signed-off-by: Nils Jacobs <njacobs8@hetnet.nl>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6022 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
- Drop banner(), use printk()s instead.
- Uncomment a few printk()s, if a users doesn't want to see them he/she
can lower the debug level.
- Replace print_emerg() with printk(BIOS_EMERG) etc.
Also change 'Assymetirc' into 'Asymmetric', thanks to Idwer for spotting.
This is Abuild and boot tested.
Signed-off-by: Nils Jacobs <njacobs8@hetnet.nl>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6021 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
- Drop commented out "config chip.h" and a duplicate link to a datasheet.
- F71805F -> F71805F/FG, to mention all variants.
- Use u8/u16/ etc. everywhere.
- Add a missing (C) line.
- Fix up a bunch of pnp_dev_info[] structs according to the datasheets.
- Fintek F71889: Drop res1/PNP_IO1 from KBC, there's no 0x62/0x63 register
pair on this Super I/O.
- Fintek F71863FG: This Super I/O _does_ have a keyboard/mouse LDN, add the
respective code in superio.c. Also: Add missing LDNs to f71863fg.h.
- i3100: Add some more comments and datasheet infos.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6020 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Also:
- Improve a few code comments, fix typos, etc.
- Change a few more variable types to u8/u16/u32 etc.
- Make some very long lines fit into 80chars/line.
- Drop a huge duplicated comment, use "@see" to refer to the other one.
- Reduce nesting level a bit by restructuring some code chunks.
- s/Config.lb/devicetree.cb/ in a few places.
Abuild-tested.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6019 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Signed-off-by: Myles Watson <mylesgw@gmail.com>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6018 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Untested, but should work mostly (even though some TODOs remain).
Signed-off-by: Alec Ari <neotheuser@ymail.com>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6017 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
This is Abuild and boot tested.
Signed-off-by: Nils Jacobs <njacobs8@hetnet.nl>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6016 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
This is Abuild and boot tested.
Signed-off-by: Nils Jacobs <njacobs8@hetnet.nl>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6015 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
and gx2/raminit.c.
This is Abuild and boot tested.
Signed-off-by: Nils Jacobs <njacobs8@hetnet.nl>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6014 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
hang. Also need to set lane config to 0x00 for autonegotiation.
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Acked-by: Rudolf Marek <r.marek@assembler.cz>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6013 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
variant. It also adds additional dev_find_device calls in k8t890_ctrl.c for
subfunctions 3 and 7.
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Acked-by: Rudolf Marek <r.marek@assembler.cz>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6012 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Also, change the GX2 boards to use it.
Add a processor speed setting function in human readable MHz and remove
the useless and broken PLLMSR settings (the processor speed was hardcoded
to 366MHz in pll_reset.c).
Signed-off-by: Nils Jacobs <njacobs8@hetnet.nl>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6011 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Nils Jacobs <njacobs8@hetnet.nl>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6010 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Also, add a copyright header to pll_reset.c.
Signed-off-by: Nils Jacobs <njacobs8@hetnet.nl>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6009 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Nils Jacobs <njacobs8@hetnet.nl>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6008 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6007 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
- via/epia-n/mptable.c
- intel/eagleheights/mptable.c (commented out anyway)
- asus/p2b-d/mptable.c
- asus/p2b-ds/mptable.c
Some files still incorrectly contain some smp_write_ioapic() lines from
the original mptable utility target (Supermicro P4DPE), which has one
IOAPIC in the southbridge (Intel ICH3-S), two IOAPICs contained in
the first P64H2, and two more in the second P64H2, i.e. 5 IOAPICs in total.
However, none of the boards where this chunk of code is present has
multiple IOAPICs (and even if they had, the PCI devices where those are
located would probably be different anyway), so drop the incorrect
mptable.c contents.
Also drop the lines from the mptable utility, so that future mptable.c files
don't incorrectly inherit any of this stuff.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Jonathan Kollasch <jakllsch@kollasch.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6006 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Scott Duplichan <scott@notabs.org>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6005 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
- Add "select IOAPIC" in the board's Kconfig file.
- Set CONFIG_MAX_PHYSICAL_CPUS to 2 on the board. There are two
CPU sockets (Slot 1) and each CPU can only have one core, multi-core CPUs
didn't exist in that era (CONFIG_MAX_CPUS was set to 2 already).
- Drop useless/duplicated enable_lapic() call from ASUS P2B-DS's romstage.c,
that function is always called if either CONFIG_SMP and/or CONFIG_IOAPIC
are set.
- Rework ASUS P2B-DS mptable.c to fix a number of things:
- Convert it to use mptable_write_buses() as all mptable.c files should do.
- Fix incorrect IOAPICID (it's 0x11 for the external 82093AA IOAPIC).
- Fix a bunch of hardcoded bus IDs, remove incorrect entries, etc.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6004 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Jonathan Kollasch <jakllsch@kollasch.net>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6003 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Jonathan Kollasch <jakllsch@kollasch.net>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6002 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6001 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
operation within is NULL anyway.
Signed-off-by: Jonathan Kollasch <jakllsch@kollasch.net>
Acked-by: Jonathan Kollasch <jakllsch@kollasch.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6000 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5999 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
- Add enable_intel_82093aa_ioapic() which enables IOAPIC usage in the
Intel 82371EB southbridge (sets the proper chip-select) and sets an
IOAPIC ID.
- We only call enable_intel_82093aa_ioapic() if a board does "select IOAPIC"
as on 82371EB-based boards the IOAPIC is an external chip (not integrated
in the southbridge) and it's only populated on multi-CPU boards.
That is, we cannot unconditionally enable it, only on SMP-capable boards.
- Due to the reason explained above, remove "select IOAPIC" from
src/southbridge/intel/i82371eb/Kconfig, and add it to
src/mainboard/asus/p2b-d/Kconfig.
- Also set CONFIG_MAX_PHYSICAL_CPUS to 2 on ASUS P2B-D. There are two
CPU sockets (Slot 1) and each CPU can only have one core, multi-core CPUs
didn't exist in that era (CONFIG_MAX_CPUS was set to 2 already).
- Drop useless/duplicated enable_lapic() call from ASUS P2B-D's romstage.c,
that function is always called if either CONFIG_SMP and/or CONFIG_IOAPIC
are set.
- Rework ASUS P2B-D mptable.c to fix a number of things:
- Convert it to use mptable_write_buses() as all mptable.c files should do.
- Fix incorrect IOAPICID (it's 0x11 for the external 82093AA IOAPIC).
- Fix a bunch of hardcoded bus IDs, remove incorrect entries, etc.
This is build-tested on ASUS P2B-D, and also boot-tested successfully there.
On Linux I now get two entries in /proc/cpuinfo (where only one appeared
before this patch), i.e. both populated CPUs are found.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5998 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Jonathan Kollasch <jakllsch@kollasch.net>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5997 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
boards using ck804_early_setup.c that select CK804_USE_NIC.
Signed-off-by: Jonathan Kollasch <jakllsch@kollasch.net>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5996 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Jonathan Kollasch <jakllsch@kollasch.net>
Acked-by: Jonathan Kollasch <jakllsch@kollasch.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5995 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Additionally, make the second SMBus more accessible in romstage.
Signed-off-by: Jonathan Kollasch <jakllsch@kollasch.net>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5994 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Also, make them all fit in 80chars/column, fix some whitespace issues
and also some typos I noticed.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5993 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
local ints. This is wrong in most coreboot mptables, probably all
generated by util/mptable/mptable.c.
After fixing this now XP can boot in MPS mode on my M2V.
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5992 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Jonathan Kollasch <jakllsch@kollasch.net>
Acked-by: Patrick Georgi <patrick.georgi@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5991 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Right now, it breaks the build of bootblock enabled boards
with that chipset.
Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de>
Acked-by: Patrick Georgi <patrick.georgi@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5990 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de>
Acked-by: Patrick Georgi <patrick.georgi@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5989 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
eliminates the compiler warning that causes the build to fail.
Signed-off-by: Scott Duplichan <scott@notabs.org>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5988 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
- Drop sig[], oem[], and productid[] fields in all mptable.c files, no
longer needed. The sig[] is always the same ("PCMP"), the oem[] is
currently also always the same ("COREBOOT"), and productid is being
passed into mptable_init() directly as string now.
- LAPIC_ADDR is passed in as parameter, too. While at the moment it's
always the same value that is passed in, the LAPIC base address could
also be relocated theoretically, so keep it as parameter for now.
- Fix a few productid entries, they were (partially) incorrect:
- DK8S2 (was "DK8X", copypaste)
- 939A785GMH (was "MAHOGANY", copypaste)
- X6DHE-G (was "X6DHE", incomplete board name)
- H8DME-2 (was "H8DMR", copypaste)
- H8QME-2+ (was "H8QME", incomplete board name)
- X6DHE-G2 (was "X6DHE", incomplete board name)
- X6DHR-iG2 (was "X6DHR-iG", incomplete board name)
- GA-M57SLI-S4 (was "M57SLI", incomplete board name)
- KINO-780AM2 (was "KINO", incomplete board name)
- DL145 G1 (was "DL145G1", small fix as per vendor website)
- DL145 G3 (was "TREX", wrong board name)
- DL165 G6 (was "HP DL165 G6", drop vendor)
- S2912 (was "S2895", copypaste)
- VT8454c (was "VIA VT8454C", drop vendor, lower-case "c")
- EPIA-N (was "P4DPE", copypaste)
- pc2500e (was "PC2500", incorrect name)
- S1850 (was "S2850", copy-paste)
- MS-7135 (was "MS7135")
- MS-9282 (was "MS9282")
- MS-9185 (was "MS9185")
- MS-9652 (was "K9ND MS-9652")
- Ultra 40 (was "ultra40")
- E326 (was "E325", copypaste)
- M4A785-M (was "TILAPIA", copypaste)
- P2B-D (was "ASUS P2B-D", drop vendor)
- P2B-DS (was "ASUS P2B-DS", drop vendor)
- Adapt the mptable utility to use mptable_init() too.
Abuild-tested.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Patrick Georgi <patrick.georgi@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5987 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|
|
Signed-off-by: Peter Stuge <peter@stuge.se>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5986 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
|