| Age | Commit message (Collapse) | Author |
|---|
|
Intel PDGs starting from Skylake / Sunrise Point state that, different
from the general recommendation in digital electronics, unconnected
GPIOs defaulting to GPIO mode do explicitly not require termination.
The reason for this is, that these GPIOs have the `GPIORXDIS` bit set,
which effectively disconnects the pad from the internal logic by
disabling the input buffer.
This bit - besides `GPIOTXDIS` - can also be set explicitly by using
the gpio macro `PAD_NC(pad, NONE)`.
In some cases, a pull resistor may be required due to bad board design
or when a vendor sets the RX/TX disable bits together with a pull
resistor and schematics are not available to check if the pad is really
unconnected or just unused. In this case the pull resistor should be
kept.
Pads defaulting to native functions usually don't need special handling.
However, when pads requiring external pull-ups are missing these due to
bad board design, they should be configured with `PAD_NC` to disconnect
them internally.
Rewrite the documentation to reflect these new findings.
Also clarify the comment in soc/intel gpio code accordingly.
Change-Id: Id01b197ebe8f2b8bb4ecf3d119ec2298b26d9be0
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52139
Reviewed-by: Tim Crawford <tcrawford@system76.com>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Update LTE USB port configuration at run-time after probing the firmware
config. By default the concerned USB port takes the Type-A port
configuration.
BUG=b:186380807
BRANCH=dedede
TEST=Build and boot to OS in metaknight
Change-Id: I5ad5a1670adef54075923cf912fb41a1ce776155
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52960
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: David Wu <david_wu@quanta.corp-partner.google.com>
Reviewed-by: Evan Green <evgreen@chromium.org>
Reviewed-by: Raymond Wong <wongraymond@google.com>
|
|
This callback is required to update the devicetree config at run-time
after probing the firmware config.
BUG=b:186380807
BRANCH=dedede
TEST=Build and boot to OS in metaknight.
Change-Id: I857211bfc4beb36ab225f3786c1707336a34aae9
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52887
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Evan Green <evgreen@chromium.org>
Reviewed-by: Raymond Wong <wongraymond@google.com>
|
|
Remove a blank line and correct the indentation of another line.
Change-Id: Id66f0a847720713c1d3445ac70a9e075228dfe88
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54017
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
For consistency with other log messages, print bus numbers in decimal.
Change-Id: Ib08ae40fc67c5f8fafd760e8dbb729d6de34c2bb
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54015
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Change-Id: I1225757dbc4c6fb5a30d1aa12987661a0a6eb538
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52969
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Change-Id: I15846bf23e49666e4948f623d6320d5c29e00bd4
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54004
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This is still causing boot errors on zork:
coreboot-4.13-3659-g269e03d5c42f Fri May 7 22:03:11 UTC 2021 bootblock starting (log level: 8)...
Family_Model: 00820f01
PSP boot mode: Development
Silicon level: Pre-Production
Set power off after power failure.
PMxC0 STATUS: 0x800 BIT11
I2C bus 3 version 0x3132322a
DW I2C bus 3 at 0xfedc5000 (400 KHz)
FMAP: area COREBOOT found @ 875000 (7909376 bytes)
ASSERTION ERROR: file 'src/commonlib/bsd/cbfs_mcache.c', line 106
BUG=b:177323348
TEST=Boot ezkinil to OS
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I68b4b73670e750207414f0d85ff96f21481be8ce
Reviewed-on: https://review.coreboot.org/c/coreboot/+/53933
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add EMCP LPDDR4X DDR FEPRF6432-58A1930 for ram id 9.
BUG=b:186141919
BRANCH=kukui
TEST=New Emcp can boot normally on kakadu/katsu
Signed-off-by: Sunway <lisunwei@huaqin.corp-partner.google.com>
Change-Id: Ieaf05a0a7b0c0671c07b0df29319ebd91fe63e57
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54009
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Setup APU mbox's functional configuration registers.
BUG=b:186369803
BRANCH=asurada
TEST=boot asurada correctly
Signed-off-by: Chien-Chih Tseng <chien-chih.tseng@mediatek.com>
Change-Id: If05a8af1a2f96598adcf70e15003e4f5dc94e337
Signed-off-by: Flora Fu <flora.fu@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48622
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Building the cbnt-prov tool requires godeps which does not work if
offline. Therefore, add an option to provide this binary via Kconfig.
It's the responsibility of the user to use a compatible binary then.
Change-Id: I06ff4ee01bf58cae45648ddb8a30a30b9a7e027a
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51982
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Change-Id: I4113b1496e99c10017fc1d85a4acbbc16d32ea41
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51975
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
eint event mask register is used to mask eint wakeup source.
All wakeup sources are masked by default. Since most MediaTek SoCs do
not have this design, we can't modify the kernel eint upstream driver to
solve the issue 'Can't wake using power button (cros_ec) or touchpad'.
So we add a driver here to unmask all wakeup sources.
Change-Id: I703d87e3dc49cf4e0b7ff0c75a6ea80245dd73d3
Signed-off-by: Yidi Lin <yidi.lin@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54007
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
UFS reference clock (refclk) is enabled by default, which will cause
the UFSHCI to hold the SPM signal and lead to suspend failure. Since
UFS kernel driver is not built-in, disable refclk in coreboot stage.
Change UFSHCI base register to 0x11270000.
Signed-off-by: Yidi Lin <yidi.lin@mediatek.com>
Change-Id: I1386e59f802a9e3c938a7e8dbeea547fbcb02709
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54011
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
Fixes compilation on FreeBSD CURRENT, and possibly other releases.
The compiler, clang, complained about:
util/cbfstool/cbfstool.c:181:40: error: implicit declaration of function 'memmem' is invalid in C99 [-Werror,-Wimplicit-function-declaration]
util/cbfstool/cbfstool.c:181:31: error: incompatible integer to pointer conversion initializing 'struct metadata_hash_anchor *' with an expression of type 'int' [-Werror,-Wint-conversion]
Signed-off-by: Idwer Vollering <vidwer@gmail.com>
Change-Id: I45c02a21709160df44fc8da329f6c4a9bad24478
Reviewed-on: https://review.coreboot.org/c/coreboot/+/53996
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I79530c91424112247e485a5a41debc666e0072d4
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54003
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I28f262078cf7f5ec4ed707639e845710a8cc56ea
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/53926
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Fix booting issues on google/kahlee introduced by CB:51723.
Update use inital apic id in smm_stub.S to support xapic mode error.
Check more bits(LAPIC_BASE_MSR BIT10 and BIT11) for x2apic mode.
TEST=Boot to OS and check apicid, debug log for CPUIDs
cpuid_ebx(1), cpuid_ext(0xb, 0), cpuid_edx(0xb) etc
Signed-off-by: Wonkyu Kim <wonkyu.kim@intel.com>
Change-Id: Ia28f60a077182c3753f6ba9fbdd141f951d39b37
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52696
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Signed-off-by: Jonathan Zhang <jonzhang@fb.com>
Change-Id: Ibead1c75bb4e41fedc2799366b5b006d76fc8f4e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52735
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: Ifa58a9ac7c6dcc391cd9942295319a8677cd4492
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54008
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
No board defines this macro. In preparation to drop OptionsIds.h files
from mainboards, remove commented-out references to `IDS_DEBUG_PORT`.
Change-Id: I67a10d863aeea9e1b91c38aa02d19106b7b97659
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/53981
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michał Żygowski <michal.zygowski@3mdeb.com>
|
|
This macro is not used anywhere in AGESA. Remove all references.
Change-Id: Ibc2876a5a8419ec4fa5a793bb996f5c14d989bac
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/53980
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michał Żygowski <michal.zygowski@3mdeb.com>
|
|
This macro is not used anywhere in AGESA. Remove all references.
Change-Id: I9cd9fa0dc25b1143f8b4c1f20beffba638437398
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/53979
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michał Żygowski <michal.zygowski@3mdeb.com>
|
|
This macro is not used anywhere in AGESA. Remove all references.
Change-Id: Icae0ecae77a20e1568440e3191a29db33b5581d8
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/53978
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michał Żygowski <michal.zygowski@3mdeb.com>
|
|
These global variables are not used anywhere. Drop them.
Change-Id: I3fe60b970153d913ae7b005257e2b53647d6f343
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/53977
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Commit 6b5bc77c9b22c398262ff3f4dae3e14904c57366 (treewide: Remove "this
file is part of" lines) removed most of them, but missed some files.
Change-Id: Ib8e7ab26a74b52f86d91faeba77df3331531763f
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/53976
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
soc_memory_init_params() does not only configure memory init parameters.
Despite its name, it also configures many other things. Therefore, merge
it into its caller function platform_fsp_memory_init_params_cb() to
prevent confusions.
Built clevo/l140cu with BUILD_TIMELESS=1. coreboot.rom remains the same.
Change-Id: Id3b6395ea5d5cb714a412c856d66d4a9bcbd9c12
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52491
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
LPC, P2SB and Power Management controller are always needed. Thus,
enable them by default.
Change-Id: I20b8cbe536da70fccc3d11e1eedf4a5e14bfc862
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/53925
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
Signed-off-by: Jonathan Zhang <jonzhang@fb.com>
Change-Id: I6a4027bf51b3a189e64211e77621b3dd6c80b00d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52864
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Intel Sapphire Rapids Scalable Processor is a 4th generation
processor of Intel Xeon Scalable Processor family.
Signed-off-by: Jonathan Zhang <jonzhang@fb.com>
Change-Id: Idf492d6e7993b9d55d6cd865e721c81876cee9a4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52863
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The values were copied from Foxconn D41S, which uses a different codec.
Adjust the codec config as per the settings dumped from vendor firmware.
Change-Id: If6a4c41b5d424adb23ebef402d2d2ad21269fe25
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/53914
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Some changes:
- bg-prov got renamed to cbnt-prov
- cbfs support was added which means that providing IBB.Base/Size
separatly is not required anymore. Also fspt.bin gets added as an
IBB to secure the root of trust.
Change-Id: I20379e9723fa18e0ebfb0622c050524d4e6d2717
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52971
Reviewed-by: Christian Walter <christian.walter@9elements.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This prepares for updating the intel-sec-tools submodule pointer. In
that submodule bg-prov got renamed to cbnt-prov as Intel Bootguard
uses different structures and will require a different tool.
Change-Id: I54a9f458e124d355d50b5edd8694dee39657bc0d
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52970
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
We need to modify update CmdMirror and LpDdrDqDqsRetraining parameters
for ADLRVP board.
Allowing this parameters to be filled by devicetree will allow
flexibility to update values as per board designs.
Note that both UPDs are applicable for both DDR and Lpddr memory types.
BUG=None
BRANCH=None
TEST=Build works and UPD values have been filled correctly
Change-Id: I55b4b4aee46231c8c38e208c357b4376ecf6e9d9
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51027
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Change-Id: I1d6ecdb31eef65d2e96d9251348390aa8598be6c
Signed-off-by: Yidi Lin <yidi.lin@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/53900
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
Signed-off-by: Yidi Lin <yidi.lin@mediatek.com>
Change-Id: Iab3549b5c4e7d845ddd284a0df3fb448e11fbdcb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/53899
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ib0f7da12429b6278d1e4bc5d6650c7ee0f3b5209
Reviewed-on: https://review.coreboot.org/c/coreboot/+/53940
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
This reverts commit 6eced03b25954e370e20e62f2cbe41f9d5626eae.
This prevents zork from booting. We get the following error:
eSPI cmd0-cmd2: 00080009 00000000 00000000 data: 00000000.
Error: unexpected eSPI status register bits set (Status = 0x10000010)
Error: Slave GET_CONFIGURATION failed!
This isn't a pure revert. It is more of a fix that keeps the old
behavior.
BUG=b:187122344
TEST=Boot zork an no longer see eSPI error
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: If75a35d3994b0fd23945a450032d3cc81abeb136
Reviewed-on: https://review.coreboot.org/c/coreboot/+/53932
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Cezanne must use cold resets. Change the warm reset request to always
set TOGGLE_ALL_PWR_GOOD. And, since the bit is sticky across power
cycles, set it early for good measure.
BUG=b:184281092
TEST=Majolica successfully resets using 0xcf9
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Change-Id: I7d4ca5665335b20100a5c802d12d79c0d0597ad9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52982
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Fix I2C3 setting for TPM in devicetree.
BUG=b:187341277
TEST=Build and boot into OS
Signed-off-by: Ivy Jian <ivy_jian@compal.corp-partner.google.com>
Change-Id: I728da76cee0c92c29df4c6ee8bfb4cd07a6366c4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/53891
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Loading address and size for the user app has been changed with recent
PSP release.
Signed-off-by: Kangheui Won <khwon@chromium.org>
Change-Id: If247cdf3413c6a10f4b3c92fb7e43dd1057865d9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/53904
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Verify if transfer buffer is valid before progressing further to catch
invalid transfer buffer early.
Signed-off-by: Kangheui Won <khwon@chromium.org>
Change-Id: I4c470b156944b50e581dcdee47b196f46b0993f3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52965
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
AMDFW tool stores bios dir entry to bios1_entry in picasso but
bios3_entry in cezanne. Separate getting bios_dir_addr into a function
and implement it on each platforms.
Signed-off-by: Kangheui Won <khwon@chromium.org>
Change-Id: Ie18ed7979a04319c074b9b251130d419dc7f22dc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52964
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Move all platform-specific code except direct svc calls to chipset.c.
There will be differences between each platforms and we can't put
everything into svc.c.
TEST=build firmware for zork
Signed-off-by: Kangheui Won <khwon@chromium.org>
Change-Id: Ie7a71d1632800072a17c26591e13e09e0269cf75
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52963
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
psp_verstage.bin target is already defined at
common/psp_verstage/Makefile.inc, thus removing it here.
Signed-off-by: Kangheui Won <khwon@chromium.org>
Change-Id: Ica4b09282d1c4cfc555c18ba50951458b8580826
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52962
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Build amdfw_[ab] and put them into CBFS. We can reuse FW_[AB] position
from zork since we have same flash layout and size.
Signed-off-by: Kangheui Won <khwon@chromium.org>
Change-Id: Idb31afa7a513f01593b2af75515a170dfca8d360
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52961
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable Display Controller Engine Audio endpoint to enable HDMI audio.
BUG=b:186479763
TEST=Build and boot to OS in guybrush.
Change-Id: I5e35440e8e70ee125d37c7ac30c9219ec69c7c6e
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52974
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Everybody wants a stylish stylus. Enable the power system to it.
BUG=b:186267293
TEST=connect multimeter to PP5000_PEN and see it go from 0 to 1. MAGIC!
Signed-off-by: Eric Peers <epeers@google.com>
Change-Id: I11d05c118ec9451d26136c320f3650c489e02c59
Reviewed-on: https://review.coreboot.org/c/coreboot/+/53943
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Both mt8192 and mt8195 use MT659P RTC. Move mt8192/rtc.c to common
folder and rename to rtc_mt6359p.c.
Signed-off-by: Yuchen Huang <yuchen.huang@mediatek.corp-partner.google.com>
Signed-off-by: Yidi Lin <yidi.lin@mediatek.com>
Change-Id: I73ea90512228a659657f2019249e7142c673e68e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/53897
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Both mt8192 and mt8195 use mt6359p clk_buf.
But mt8195 clk_buf uses legacy co-clock mode without srclken_rc.
Signed-off-by: Yuchen Huang <yuchen.huang@mediatek.corp-partner.google.com>
Change-Id: Ie9ee91449a7a14e77231493f807b321b2dbaa6a6
Signed-off-by: Yidi Lin <yidi.lin@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/53896
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
Change-Id: I0ed82e860612e8a62f361e60d217280f775ab239
Signed-off-by: Wenbin Mei <wenbin.mei@mediatek.com>
Signed-off-by: Yidi Lin <yidi.lin@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/53895
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
TEST=write/read EEPROM on MT8195 EVB successfully
Change-Id: Ia26e55512501e9758d7f5543d176730cf30ce03d
Signed-off-by: kewei xu <kewei.xu@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/53894
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Signed-off-by: Andrew SH Cheng <andrew-sh.cheng@mediatek.com>
Change-Id: I68ca7067f76a67c4e797437593539f8f85909edc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/53893
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
We can generate the names, so there is no need to hard code a table.
This will make the code more generic so it can be reused with picasso in
the future.
BUG=b:184766519
TEST=Dump guybrush ACPI table and verify it looks correct.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I5134d1dba4fcb9ce8cc4bfad1c619331a95f3b11
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52870
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
We can now use the GNB IO-APIC.
BUG=b:184766519
TEST=Boot guybrush to OS with `pci=nomsi amd_iommu=off noapic`
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I4df5a4583f14044d2efcde3a9de9dd85e898a11d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/53936
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
To configure and enable the IOAPIC in the graphics and northbridge (GNB)
container, FSP needs to write an undocumented register, so pass the GNB
IOAPIC MMIO base address to make it show up at that address.
BUG=b:187083211
TEST=Boot guybrush and see IO-APIC initialized
IOAPIC[0]: apic_id 16, version 33, address 0xfec00000, GSI 0-23
IOAPIC[1]: apic_id 17, version 33, address 0xfec01000, GSI 24-55
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I1e127ce500d052783f0a6e13fb2ad16a8e408b0e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52905
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The PIC IRQs are required so we can correctly set up the PCI_INT
registers. This only matters when booting in PIC mode. We don't need to
set the IO-APIC registers since the linux kernel will auto-assign those
to reduce conflicts.
BUG=b:184766519
TEST=Boot guybrush with `pci=nomsi,noacpi amd_iommu=off noapic` and
verify xhci and graphics continue to work.
$ cat /proc/interrupts
12: 285064 XT-PIC nvme0q0, nvme0q1, rtw88_pci
13: 100000 XT-PIC xhci-hcd:usb1
14: 4032 XT-PIC amdgpu, xhci-hcd:usb3
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I1d66ccd08a86a64242dbc909c57ff9685828f61f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52915
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Use the new acpigen_write_PRT to write the _PRT for each PCI bridge.
BUG=b:184766519
TEST=Dump guybrush ACPI table and verify it looks correct.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Idb559335435a95e73640e6d7fb224e16e0592326
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51556
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
This uses the new FSP PCI methods to pull the routing table and populate
the pirq data structure.
BUG=b:184766519
TEST=Boot guybrush and verify we get Got IRQ 0x1F (disabled) messages
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Ie21229cc2fb4fd5b85c0b9e933f7b43af24864b0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52914
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
These are helper methods for interacting with the
AMD_FSP_PCIE_DEVFUNC_REMAP_HOB_GUID.
BUG=b:184766519, b:184766197
TEST=Build guybrush
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Id03d0b74ca12e7bcee11f8d13b0e802861c13923
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52911
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
We can now delete the picasso specific version.
BUG=b:184766519
TEST=Build zork and verify SSDT has not changed
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Ic79014e83c9ff63cc7a6757b16764ae23b36984f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/53935
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This is loosely based off of picasso/pcie_gpp.c. This version uses the
acpigen_write_PRT_X methods to write the actual records. There are also
two functions, 1 for using the GNB, and one for using the FCH. The FCH
one is useful when the GNB IO-APIC has not been initialized.
BUG=b:184766519
TEST=Dump guybrush ACPI and verify it looks correct
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I926430074acb969ceb11fdb60ab56dcf91ac4c76
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52917
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
The method now dynamically allocates the pirq structure and uses the
get_pci_routing_table method.
BUG=b:184766519
TEST=Build guybrush and verify picasso SSDT has not changed.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I297fc3ca7227fb4794ac70bd046ce2f93da8b869
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52913
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
This allows us to use the common get_pci_routing_info and
pci_calculate_irq. The IRQ field in the struct was also filled in from
the PPR.
BUG=b:184766519
TEST=Boot ezkinil and verify SSDT table is identical.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I16d90d8c89bfcf48878c0741154290ebc52a4120
Reviewed-on: https://review.coreboot.org/c/coreboot/+/53923
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This struct is similar to `struct pci_routing` defined in
picasso/pcie_gpp.c. It additionally contains the irq used for the bridge
and is structured in a way that the FSP can provide via HOB.
The next set of CLs will migrate the pci routing functions used by
picasso into common and enable pci routing table generation for cezanne.
BUG=b:184766519
TEST=Build guybrush
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I1a8d988d125f407f0aa7bc1722d432446aa9aff8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/53922
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Document the roles we have on review.coreboot.org, the expectations
associated with them, and how to become part of any of these groups.
Change-Id: Ib31083f5a07bd89efd13ecd6aaf34a69d438d59d
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52265
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I72a9056edfddb4e2cd2e6412cb5ea72cf965f9c6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/53924
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=b:187212773, b:185481298
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I2cf50257d767525d682602cdcc5547bf001fe2ac
Reviewed-on: https://review.coreboot.org/c/coreboot/+/53921
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
TEST=Mandolin still boots into Linux and there's no ACPI warning in
dmesg.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I7e6d38ebeae5e55a4a65930b989838532ab9c446
Reviewed-on: https://review.coreboot.org/c/coreboot/+/53920
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Also add an alib_ prefix to avoid possible name collisions.
TEST=Timeless build for Mandolin results in identical binary.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ib0f220a4cde6da764bb8bc589b5f44ae16496bd7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/53918
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
These parameter IDs are defined in the AGESA Interface specification
#55483. This patch also adds a ALIB_DPTC_ prefix to the IDs and makes
the names more consistent.
TEST=Timeless build for Mandolin results in identical binary.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I75e0504f6274ad50c53faa8fcbde4d6821d85a04
Reviewed-on: https://review.coreboot.org/c/coreboot/+/53917
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The other enum entries are control IDs for the
ALIB_FUNCTION_DYNAMIC_POWER_THERMAL_CONFIG ALIB function while
DPTC_TOTAL_UPDATE_PARAMS is the total number of configuration settings
that will get passed as parameter in the ALIB call, so it shouldn't be
part of that enum.
TEST=Timeless build for Mandolin results in identical binary.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I0cb9e9d2ba579a74d916011b4ead71cc86d69a24
Reviewed-on: https://review.coreboot.org/c/coreboot/+/53916
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The ACPI ALIB function numbers are defined in the AMD Generic
Encapsulated Software Architecture (AGESA™) Interface Specification
(document #55483).
TEST=Timeless build stays the same for Mandolin (Picasso) and Gardenia
(Stoneyridge).
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I290ef0db32c65ebb2bbbe4f65db4df772b884161
Reviewed-on: https://review.coreboot.org/c/coreboot/+/53915
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The mcache is overflowed in the latest build. In order
to fix the mcache overflow, we increase the mcache size
to 0x4000 and adjust the percentage to 50% for the ro/rw
mcache. This change is for all of the volteer variants
as we see many of the volteer variants which use the
latest bios having the mcache overflow issue.
BUG=b:187095474, b:187095765, b:187234881, b:162052593
TEST=no mcache overflow in the bios log
Change-Id: If9552bc9fa5d36b1ca662c9da030ae7b137b60a8
Signed-off-by: Zhuohao Lee <zhuohao@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/53908
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
Add backlight support in sn65dsi86bridge through the AUX channel using
eDP DPCD registers, which is needed on the GOOGLE_HOMESTAR board.
Change-Id: Ie700080f1feabe2d3397c38088a64cff27bfbe55
Signed-off-by: Vinod Polimera <vpolimer@codeaurora.org>
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52663
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The SN65DSI86 eDP bridge supports two ways to read the EDID: for now
we've been using "direct mode", which works by basically making the
bridge I2C device listen to another chip address besides its own and
proxy all requests received there directly to the eDP AUX channel. The
great part about that mode is that it is super easy and hassle-free to
use. The not so great part about it is that it doesn't work: for EDID
extensions, the last byte (which happens to contain the checksum) is
somehow always read as zero. We presume this is a hardware bug in the
bridge part.
The other, much more annoying way is "indirect mode", where each byte
transmitted over the AUX channel has to be manually set up in the I2C
registers of the bridge, just like we're already doing with DPCD
transactions. Thankfully, we can reuse most of the DPCD code for this so
it's not a lot of extra code. It's a bit slower but not as much as you'd
expect (26ms instead of 18ms on my board), and the difference is not
very relevant compared to common total times for display init.
Also, some of the (previously unused) enum definitions for the AUX_CMD
mode field of the bridge had just been plain wrong for some reason, and
needed to be fixed to make this work.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I65f80193380d3c3841f9f5c26897ed672f45e15a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52959
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
PCI interrupts are level active low, so they can be shared.
BUG=b:184766519
TEST=Boot guybrush to OS with `pci=nomsi amd_iommu=off noapic`
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I439337dd66fe56790406c6d603e73512c806a19d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52957
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Replace `3` with `SaGv_Enabled`, which has the same value.
Change-Id: I05cfddfefc45ba5bfb0e684445a6d8e02d7865e3
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52098
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
SaGv is only supported on ULT/ULX hardware.
Change-Id: I25001e97cce3193629e7fa7573bf9b352362d59b
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52097
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
Change-Id: I8a2abe2cf20952491d181766a3ca492de355fc88
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52814
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Memory region 0xa0000 to 0xc0000 was not reserved, the first
PCI memory resources might get assigned in this space.
FIXES: aopen/dxplplusu PCI EHCI 0:1d.7 memory resource.
Change-Id: Ia17025bde83b91d71ad719de6348197cf92e267e
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52813
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
This will allow us to have subdirectories in common/fsp.
BUG=b:184766519
TEST=Build guybrush
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Ib3497791e1963867c8fe06a42c111e5d0503ade1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52910
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Create the volet variant of the volteer reference board by copying
the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.5.0).
BUG=b:186334008
BRANCH=None
TEST=util/abuild/abuild -p none -t google/volteer -x -a
make sure the build includes GOOGLE_VOLET
Signed-off-by: Sheng-Liang Pan <sheng-liang.pan@quanta.corp-partner.google.com>
Change-Id: Ic6ca9a78494e3819b0fb39c0bcc70fed95c2c589
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52871
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: YH Lin <yueherngl@google.com>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
|
|
Bank interleaving does not work on this platform, disable it.
AmdInitPost returns success thanks to this setting.
TEST=boot apu1 and see AGESA_SUCCESS after AmdInitPost
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Change-Id: Id555b458c61df9a27a93f44f600d1718867106ca
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52779
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Krystian Hebel <krystian.hebel@3mdeb.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Bank interleaving does not work on this platform, disable it.
Additionally enable ECC feature on SKUs supporting it. AmdIntPost
returns success thanks to these settings.
TEST=boot apu2 4GB ECC and apu3 2GB no ECC and see AGESA_SUCCESS after
AmdInitPost
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Change-Id: I010645f53b404341895d0545855905e81c89165e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52759
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Mediatek SoC uses part of the L2 cache as SRAM before DRAM is ready.
After DRAM is ready, we should invoke disable_l2c_sram to reconfigure
the L2C SRAM as L2 cache.
Signed-off-by: Yidi Lin <yidi.lin@mediatek.com>
Change-Id: I8777b0c8471fe17ffffdcb6ad5b7c00fb1d35db1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52925
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Configure Chromebook specific GPIOs, including EC_AP_INT,
SD_CD, EC_IN_RW, GSC_AP_INT and EN_SPK.
Change-Id: Id553f632412af440d21a3b51e017cb74cc27fd22
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52924
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
We need to configure CPU PCIE root port related gpios in early
boot block stage for CPU root ports to work. Since we're removing
this programming from FSP, coreboot needs to take care of programming
this GPIOs. Also we need to enable virtual wire messaging for native
gpios for CPU PCIE root ports.
Change-Id: Ieda6b6c31ce5bd5e84e4efe544bfc659283ce6f1
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52270
Reviewed-by: Balaji Manigandan <balaji.manigandan@intel.com>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add SPD support to elemi for K4AAG165WB-BCWE
BUG=b:187379245
TEST=FW_NAME=elemi emerge-volteer coreboot chromeos-wqbootimage
Change-Id: I839447a9e7c7b6558b2d0877c67dc9cf89ee792a
Signed-off-by: Wisley Chen <wisley.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52880
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
Change-Id: Ic0be2c1ffaadcc6212c548332d60d40b405abbda
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52939
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
platform_is_resuming() was using the wrong register (PM1_STS) to figure
out if the platform was resuming (PM1_CNT).
Change-Id: I1f69dca1da158aae15c6da6d4c898c71d9cdb51f
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52930
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
acpi_is_wakeup_s3() requires acpi_get_sleep_type().
Change-Id: Ibe01863e685bcbc9652a72be0632cfbd83e18380
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52929
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
On tgl, we noticed system hang if a shutdown is triggered before fsps.
The dut is unable to shutdown properly due to tcss is stuck before
tcss_init in fsps.
This change enable power button smi on jsl, tgl, adl after fsps.
it can also prevent a shutdown failure due to lack of fsps init on
certain ip.
BUG=b:186194102, b:186815114
TEST=Power on the system and pressing power button repeatedly doesn't
cause the system hang during shutdown.
Change-Id: I70b871f2676a89bc782116e02beba5c20ec51eef
Signed-off-by: Kane Chen <kane.chen@intel.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52874
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
If a power button SMI is triggered between where it is currently
enabled and before FSP-S exits, when the SMI handler disables
bus mastering for all devices, it inadvertently also disables
the PMC's I/O decoding, so the register write to actually go into
S5 does not succeed, and the system hangs.
This can be solved by skipping the PMC when disabling bus
mastering in the SMI handler, for which a callback,
smihandler_soc_disable_busmaster is provided.
BUG=b:186194102, b:186815114
TEST=Power on the system and pressing power button repeatedly doesn't
cause the system hang during shutdown.
Change-Id: I1cf5cf91ebad4a49df6679e01fc88ff60c81526c
Signed-off-by: Kane Chen <kane.chen@intel.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52873
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Mancomb uses DDR4 SODIMMs, but the default cezanne configuration is for
the LPDDR4 version. This changes to use SODIMMS.
Further changes may be needed for platform customization, so I put the
config file in variants/baseboard instead of the root mancomb directory.
BUG=b:187094481
TEST=Build only
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: Icc4dc8aec2053cb177765f57e57cac7a099508fe
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52900
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
This patch was implemented on Guybrush at CB:52352
BUG=b:185397933
TEST=Build
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: I141a504a827f37724fab0aaed7498fd543e471d6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52950
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
DISABLE_KEYBOARD_RESET_PIN - This pin goes to a test point and is not
used for the reset.
DRIVERS_UART_ACPI - Add the UART ACPI code
FW_CONFIG - Mancomb uses the firmware config interface
PSP_DISABLE_POSTCODES - The PSP is not yet initializing eSPI correctly
to send post codes to the EC, so disable them for now.
BUG=None
Test=Build
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: I39efcc8d1e0fb1e7ac0b0541a49db0ac0ee56481
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52949
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
This change fixes two problems:
1) We had the enum values for .direction and .level swapped. The naming
is very confusing...
2) ESPI_SYS is not a good event to use for EC SCI. It is a level/low
event that is only cleared by reading the eSPI status register 0x9C.
Cezanne has added a new event source that directly exposes the SCI bit.
This is the correct event source to use for EC SCI.
This same patch was added for Guybrush at CB:52673
BUG=b:186045622, b:181139095
TEST=Build
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: Iac86d2ef5bdd21fbb0a0d4e235efe4fe621023b2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52948
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This matches what we are doing on guybrush.
BUG=b:187122344, b:186135022
TEST=build
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Id61de28cd0ee762693b287b29bdd7605d4176929
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52956
Reviewed-by: Rob Barnes <robbarnes@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Using the push-pull alert was causing leakages when in S0i3. This is
because the EC drives ALERT#, so when the AP enters S0i3, the extra
current leaks into the SoC and ends up turning on the power regulators.
By using in-band ALERT#, the EC no longer drives this pin high, thus
fixing the leak. We could also have used an open drain alert, but the
rise time is less than ideal.
BUG=b:187122344, b:186135022
TEST=Measure S0i3 power on guybrush and validate it's no longer high.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I6de771aeda8feca062652f0ea9eb57d31cb68562
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52955
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Rob Barnes <robbarnes@google.com>
|
