| Age | Commit message (Collapse) | Author |
|---|
|
Update generic id to generate the SSDT1 acpi table successfully
BUG=b:196866470
BRANCH=firmware-zork-13434.B
TEST=generate SSDT1 acpi table by command "iasl -d SSDT1"
Signed-off-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
Change-Id: I09c9adc2db08e8e3905d9ba800948252230e4d54
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57286
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
|
|
The eventlog requires RTC to provide correct timestamps, so we have to
turn on the config and add the common drivers.
BUG=b:199003609
TEST=check timestamp in 'mosys eventlog list'
BRANCH=none
Signed-off-by: Chen-Tsung Hsieh <chentsung@chromium.org>
Change-Id: Ia382cd023fcbfdf2c1efeb7b32c0b99feb71effa
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57403
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
A chip entry in the devicetree is not hooked up without a device
beneath it. It seems the intention was to leave these superio
drivers unconfigured, so there should be no harm to turn the
entries into comments.
Change-Id: I6b606f35eba089b74c562084772d95be41cac39c
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57430
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
1. Disable external output reset signal in first WDT reset
to preserve WDT original reset reason for WDT issue in kernel stage.
2. After preserved WDT reset reason, do fully reset again by sending
external output reset signal.
BUG=b:194025005
TEST=boot to kernel ok and function test pass
Signed-off-by: Fengquan Chen <fengquan.chen@mediatek.corp-partner.google.com>
Change-Id: I5887a8312f4daab3cbd0a30fea0195670a932e52
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57270
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.corp-partner.google.com>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
Add Kconfig option TIANOCORE_ABOVE_4G_DECODE to pass build option to
edk2 to enable or disable "Above 4G Decode". Disabling allows certain Linux
distributions to boot such as Qubes, Zorin and Proxmox.
Requires commit `2f6d4cbcc7fa49462e607baed7626524ccd59ad3` that is
present in the `uefipayload_202107` branch of MrChromebox's edk2
repository.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: Ia3b1d15196c0ec611431af29031682fea626d19d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56223
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
|
|
Suggested-by: Martin Roth <martinroth@chromium.org>
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I0016a6c7d6581cb261cab6178268c1a86b89c839
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56831
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Jason Glenesk <jason.glenesk@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Since both functions are only called from one function each, inline them
into those functions. Also get_gpio_mux just returned the return value
of iomux_read8, so there were two functions with identical functionality
which shouldn't be the case.
Suggested-by: Martin Roth <martinroth@chromium.org>
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I5662d0226edb25a9954fa47b42e208729a79e5a9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56830
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Jason Glenesk <jason.glenesk@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This aligns the GPIO MUX access more with the GPIO control register
access and will facilitate adding support for the remote GPIO bank. Also
change the GPIO number argument type to gpio_t.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I4054656c5cc23ea942e8dd370fbbffca304755d6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56787
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Introduce amdblocks/acpimmio_legacy_gpio100.h so that the old pre-SoC
chipsets can still access the raw GPIO100 and IOMUX ACPIMMIO registers
while only allowing GPIO accesses through the GPIO API on the SoCs.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I18872dfa40d53ba8b0d7802eec52ede5e2ae617a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56786
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Move those two functions near the top of the file to have all functions
that do the hardware accesses in one place.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: If787e6e1d124a932beafd73e5ce7d0ce4869e800
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56782
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Use unsigned integers for variables that aren't supposed to become
negative.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I5ee037221b9818b0474fe0376323e522c1b3b516
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56701
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I7cf9cbd2a287dcfe3a47a8a6b164c2b3d8ae95d6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56700
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Since the raw GPIO MMIO register access is now only used inside the
gpio_banks block, the gpio_read32 and gpio_write32 functions can be
moved to that block to reduce the visibility and enforce the usage of
the functions provided by the gpio_banks block.
The iomux_read8 and iomux_write8 functions can't be easily moved to the
gpio_banks block, since it's also used in the pre-SOC AMD chipsets that
use the ACPIMMIO access functions directly.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ia0d6dea72c6bebbbe6ce545bedfc74f91e0042c4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56781
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Jason Glenesk <jason.glenesk@amd.corp-partner.google.com>
|
|
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I7d7a8c5a7188fd558a577352f8b246e61f3edd63
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56780
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
The I2C code should use some GPIO API to access the GPIO registers
instead of accessing the GPIO MMIO regions itself.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I84dff381ad86e0c7f879f0f079186aec9cafc604
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56779
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
No need to do raw GPIO MMIO accesses when basically the same
functionality can be achieved by using existing APIs. Using the existing
GPIO API instead of raw GPIO MMIO register accesses allows containing
all direct GPIO MMIO accesses inside the common AMD GPIO code which will
be done in subsequent patches. Since the value parameter of gpio_set is
int, change the type of the val parameter of drive_scl to int as well
even though I'm not sure why a signed integer was used for this in the
common GPIO API. Since program_gpios already configures the SCL GPIOs as
outputs, gpio_set can be used in drive_scl which only sets the output
value, but doesn't configure the direction.
TEST=The waveform on the SCL pin of I2C3 on a barla/careena Chromebook
looks similar to the same as before during the reset_i2c_peripherals
call, but due to the additional overhead of the read-modify-write to the
GPIO register instead of just a write, the pulse width gets about 50%
longer. Since the udelay call in drive_scl still has an open TODO to
make this configurable and the pulses being longer is in the safe side,
this side-effect can be addressed in a follow-up patch.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ic323cebc1c83ecd6f0e1fbab419c69489d77face
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56777
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
drive_scl in soc/amd/common/block/i2c/i2c.c writes the raw GPIO MMIO
configuration register and drives it as output, so don't initially
configure the GPIO as input with no pull up/down. This is a preparation
to use the common AMD GPIO access functions instead of the raw register
accesses, since the gpio_set function only sets the output value, but
doesn't reconfigure the direction. Using gpio_output there instead would
reconfigure the direction as well, but would result in doubling the
number of MMIO accesses, so just configure the GPIOs correctly right
away to avoid that.
TEST=The waveform on the SCL pin of I2C3 on a barla/careena Chromebook
looks exactly the same as before during the reset_i2c_peripherals call.
This was probed at the SCL pad of the unpopulated I2C level shifter on
the side that is connected to the SoC.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I8e94afe0c755a02abcc722d5094e220d8781f8f5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56807
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Update fw_config.c based on the schematic carbine_adl-p_evt_20210901.pdf
BUG=b:190688567
TEST=USE="project_gimble emerge-brya coreboot" and verify it builds
without error.
Signed-off-by: Mark Hsieh <mark_hsieh@wistron.corp-partner.google.com>
Change-Id: I240c0cd777d215e46a0a661aaac63a187311019d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57360
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
NVMe needs extra time to run boot process, enable power and deassert reset for NVMe earlier in the boot flow that gimble can successfully boot into OS with non-serial coreboot.
BUG=b:198405404
TEST=USE="project_gimble emerge-brya coreboot" and verify it builds
without error.
Signed-off-by: Mark Hsieh <mark_hsieh@wistron.corp-partner.google.com>
Change-Id: Ib76965db2a6cd0c19be4043fec73af297a619c7b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57359
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch enables SaGv support for gimble.
BUG=b:198531517
TEST=USE="project_gimble emerge-brya coreboot" and verify it builds
without error.
Signed-off-by: Mark Hsieh <mark_hsieh@wistron.corp-partner.google.com>
Change-Id: I29887418827614afb10558c6958c9c5e9667079e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57357
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Marx Wang <marx.wang@intel.com>
|
|
Roughly half the boards had a "title" comment for the board. This adds
it for the rest of the boards to make everything consistent.
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: Ib941318842136212727f56fc6130381c5c9cd55b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57390
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
copy config from guybrush reference board.
remove wwan & speaker amp due to the different solution is
used on nipperkin.
BUG=b:194031783
BRANCH=guybrush
TEST=emerge-guybrush coreboot chromeos-bootimage
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Change-Id: I58a9b8393a965a9c793802d3e660829863b74375
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57263
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Verified by running following on vendor
and observing mPCIe USB device (dis)appearing:
echo 1 > /sys/bus/pci/devices/0000:00:16.0/remove
echo 1 > /sys/bus/pci/devices/0000:00:16.2/remove
echo 1 > /sys/bus/pci/devices/0000:00:00.0/rescan
Change-Id: I6ee7e3679c9cd87b81f955c68ec89db1dda30aec
Signed-off-by: Sebastian 'Swift Geek' Grzywna <swiftgeek@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57307
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
The COMe module connector implements 8 GPIO lines from the CPLD/EC pins.
Use the Kempld GPIO driver[1] to configure these pins in accordance with
the COM Express Module Base Specification [2].
TEST = Set different logic states for the pin configured as outputs and
check them with an oscilloscope.
[1] CB:47595 , Change-Id: Id767aa451fbf2ca1c0dccfc9aa2c024c6f37c1bb
[2] page 79-81, PICMG (R) COM.0 Revision 3.0 COM Express (R) Base
Specification - March 31, 2017.
Change-Id: I7d354aa32ac8c64f54b2bcbdb4f1b8915f55264e
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54380
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
There is no existing documentation on how `device ref` and aliases work
in the devicetree, and the behavior around devices not being in the same
location is difficult to discern as well as somewhat unexpected.
This should help prevent confusion leading to bugs such as the one fixed
by https://review.coreboot.org/c/coreboot/+/57298
Change-Id: I4b30f7d531cfc3453d6523a76084f1969125b4bf
Signed-off-by: Peter Marheine <pmarheine@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57354
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Platforms that rely on the FSP for parts of the hardware initialization
likely won't boot successfully when no FSP binaries are added during the
build, so print a warning at the end of the build in this case.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Suggested-by: Nico Huber <nico.h@gmx.de>
Suggested-by: Martin Roth <martinroth@google.com>
Change-Id: I6efc184ecc4059818474937fd31574f703c9bdc6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57368
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Haswell has its Mini-HD device and is at card0, so we need to search
for the PCH HD Audio device instead of using card0.
Change-Id: I2bc420fdbe9731ae835f63add85db79f04201da4
Signed-off-by: Iru Cai <mytbk920423@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/34357
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch also adds LynxPoint and WildcatPoint-LP IOBP registers,
which is used to get the USB and SATA configuration values for
autoport.
Change-Id: I1f11640fdff59a5317f19057476f7e48c2956ab9
Signed-off-by: Iru Cai <mytbk920423@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41473
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Updating from commit id ccc56f4:
vboot: add x86 SHA256 ext support
to commit id 4423276:
crossystem: add a hwid override mechanism from chromeos-config
Signed-off-by: Thejaswani Putta <thejaswani.putta@intel.com>
Change-Id: I7bd73b9f6c0492f96c336b61e21ecae37b8f3606
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57322
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Thejaswani Putta <thejaswani.putta@intel.corp-partner.google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Change-Id: I15203920546363466eef567136821b59dda763b0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54648
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I082d31d59660c48065f9390975817d3ed553da2d
Signed-off-by: Peter Lemenkov <lemenkov@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55606
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Change-Id: Ibfa877fc328d64be4de372fb7f4401717158ed9e
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52743
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
These defines are copy-paste leftovers from Kunimitsu. However, neither
Saddle Brook nor KBLRVP use memory-down, so drop the unneeded defines.
Change-Id: I396aeaa634f619be7be0ee97c0cab1c682f53ff2
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57231
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
The I2C #5 device is already disabled in the devicetree.
Change-Id: Ia4970dc07ef57e8184bce395a446974a22eddb08
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57230
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
Disable devicetree devices disabled in the `SerialIoDevMode` array.
These devices get disabled by FSP-S, and coreboot doesn't see them.
Change-Id: I8dbb45c96eae5188e5999df9a458f06f6b196adf
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57229
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
All KBLRVP variants select the `INTEL_LPSS_UART_FOR_CONSOLE` Kconfig
option and set `UART_FOR_CONSOLE` to `2`, so that UART #2 is used as
coreboot console. However, the LPSS console driver requires the LPSS
UART to be memory-mapped (and not I/O-mapped, like Super I/O UARTs).
KBLRVP variant RVP8 uses `PchSerialIoLegacyUart` for UART #2, which
makes FSP-S configure UART #2 in legacy, I/O-mapped mode. This most
likely results in the UART console not working after FSP-S has run.
This change updates RVP8 to use `PchSerialIoSkipInit` for UART #2, like
the other KBLRVP variants do.
Change-Id: Ic5c78f5895fe1dd5e7be6ef7aec3de6940dd2475
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57228
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
This is most likely a copy-paste remnant, and will never be needed for
RVP8: the SDXC device does not exist on PCH-H (and RVP8 uses a PCH-H).
Change-Id: I69059a88dcdb032beaab5fb03981dccbae0db02e
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57227
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
The I2C #4 and I2C #5 devices do not exist on PCH-H. Disable the devices
using the PCH-H variants' overridetrees (the base devicetree enables I2C
#4), set the `SerialIoDevMode` entries to `PchSerialIoDisabled` and drop
inapplicable I2C #4 voltage settings.
Change-Id: I56f34fa2004993d2123ccd5c1008fd71682ec2bd
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57226
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Get rid of several unused PCH PCI device macros. These macros expand to
a call to the `pcidev_path_on_root_debug()` function, which only exists
to debug bad code. If needed, these macros should be reimplemented with
the `pcidev_path_on_root()` function instead.
Tested with BUILD_TIMELESS=1, Purism Librem 13 v1 remains identical.
Change-Id: I366e064f3fe708b55fb381aee25b2795b1c61142
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55529
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
The `dev_optimize()` function is neither defined nor used anywhere in
the tree. Drop its unnecessary declaration.
Change-Id: I902bda3244c6496a04f364fad3ecbbdd118dd543
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57398
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
These two files are the only places where the `others` keyword is
capitalised. Use lowercase for consistency with the rest of the tree.
Change-Id: I6b785e28d1d00a11b802a44348a7132ceb6b599d
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57399
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change adds a new Kconfig `SOC_INTEL_ENABLE_USB4_PCIE_RESOURCES`
that can be selected by mainboard to reserve hotplug resources for
USB4 at the SoC level. `ADL_ENABLE_USB4_PCIE_RESOURCES` is dropped
from soc/intel/alderlake and instead the newly added Kconfig is now
used. This new Kconfig is added so that the same config can be used
across different platforms. In following changes, this Kconfig is
utilized by TGL as well.
Change-Id: Id7c359a0e255c43c2732f6cbe287bc7da14a46e3
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57124
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Mainboard information can be found in the included documentation.
Change-Id: I9dfc58bb99e14cd9dac2ac53afc0ea11d2252aa9
Signed-off-by: Bill XIE <persmule@hardenedlinux.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57191
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
There are multiple HECI clients in the CSE. heci_send_receive() is
sending HECI messages to only the MKHI client. Add an argument to
heci_send_receive() function to provide flexibility to the caller to
select the client for which the message is intended.
With the above change heci_send() and heci_receive() functions are
no longer required to be exposed.
In the follow-up patches there will be messages sent to one other
client.
BUG=None
BRANCH=None
TEST=Build and boot brya. HECI message send and receive to MKHI client
is working. Also, MEI BUS message to disable bus is working.
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Change-Id: Icde6d0155b62472b6a7caadc5fc8ea2e2ba6eb0c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57295
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Add tpch device information for thermal functionality under dptf
for alderlake soc based platform.
BUG=b:198582766
BRANCH=None
TEST=Build FW and test on brya0 board
Change-Id: Iad8e8bc0b7a104bbe582bc477936d0d00087f1d1
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57097
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Add new thermal control mechanism for pch device under dptf driver.
This provides support of different control knobs for FIVR.
BUG=b:198582766
BRANCH=None
TEST=Build FW and test on brya0 board
Change-Id: I035d2844b9ba6a9532ae006fc1c43e34cb94328a
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57096
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Configure I2C high / low time in device tree to ensure I2C
CLK runs under I2C_SPEED_FAST (400 kHz).
Measured I2C frequency just as below after tuning:
Touchpad: 386.7kHz
Touchscreen: 387.4kHz
Audio: 385.7kHz
P-sensor: 378.1kHz
BaUG=b:197247706
BRANCH=dedede
TEST=Build and check I2C clock is under 400kHz
Signed-off-by: stanley.wu <stanley1.wu@lcfc.corp-partner.google.com>
Change-Id: Ic5d5660181f36f161ae04cbf5003f6d7ad4bc16f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57297
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Henry Sun <henrysun@google.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Add MT53E512M32D1NP-046 WT:B supported memory part in the
mem_parts_used.txt and generate the SPD ID for the part. Manufacturer
is Micron, and the memory part is 1anm Tech, difference to 1xnm Tech
on MT53E512M32D2NP-046.
BUG=b:194223174
BRANCH=dedede
TEST=Build the gooey board.
Change-Id: I7b83126a2bf98bb9d0ca05d397c288e0d99ed781
Signed-off-by: Stanley Wu <stanley1.wu@lcfc.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57310
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add PMC IPC commands information for FIVR control functionality.
BUG=b:198582766
BRANCH=None
TEST=Build FW and test on brya0 board
Change-Id: Iccb43b7ba4f0765499bf1844efbbb526bd671a8f
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57095
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Currently maximum VBT data size for Jasper Lake is 8KB, but Bugzzy
would use VBT data over 8KB. This change makes use of Kconfig option to
increase the maximum VBT data size to 9KB for Jasper Lake.
BUG=b:194029827
BRANCH=dedede
TEST=build and boot bugzzy and verify fw screen is loaded
Change-Id: I0abe1ba5609b48a8a8b15f88bec28342ce26c78f
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57201
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Drawper change LTE reset pin from GPP_H0 to GPP_H17 from DVT phase.
BUG=b:198117092
TEST=emerge-dedede coreboot
Signed-off-by: Wisley Chen <wisley.chen@quanta.corp-partner.google.com>
Change-Id: Ib65580babf7d21535df2bd8d33bb19261bebfe15
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57204
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Henry Sun <henrysun@google.com>
|
|
TEST=none
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Change-Id: I6346b087543217c78f87751051a4f38b23c566d2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57389
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
|
|
Guybrush based boards must usa a dedicated eSPI alert#.
Must be open drain to prevent power leaks.
Keep guybrush reference board in-band since alert# may not be connected.
BUG=b:198409370
TEST=Build guybrush and nipperkin, boot guybrush
BRANCH=None
Change-Id: I4b23bfc6a1167aebfde5acd524fda043b63163dc
Signed-off-by: Rob Barnes <robbarnes@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57313
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Use the support from the previous patch to have coreboot lock the PAM
registers instead of the FSP when the lockdown configuration is set to
coreboot.
Change-Id: Ib6fce70d6b0386906850884880dadbf45597452d
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57185
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Use the support from the previous patch to have coreboot lock the PAM
registers instead of the FSP when the lockdown configuration is set to
coreboot.
Change-Id: I6ae22f9df4834508dfa304050fad44d45df45334
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57184
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Use the support from the previous patch to have coreboot lock the PAM
registers instead of the FSP when the lockdown configuration is set to
coreboot.
Change-Id: I10f859f30b260d012f0bc8755f32413d8b2cf267
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57183
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Rename two functions that have `walk` in their name but do not perform
any walk. The new names are derived from the comments just above these
functions' definitions. Also, remove these now-redundant comments.
Change-Id: I380a5b60b3f4e820e8f6d6f960826de97c0446be
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57361
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Error out when the FSP binaries that are supposed to be added aren't
specified.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Suggested-by: Nico Huber <nico.h@gmx.de>
Change-Id: Ie5f2d75d066f0b4e491e9c8420b7a0cbd4ba9e28
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57219
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Like USE_AMD_BLOBS and USE_QC_BLOBS in the case of the AMD and Qualcomm
repos, FSP_USE_REPO controls if the Intel FSP repo will get checked out
and will be available during the Jenkins runs. ADD_FSP_BINARIES will get
selected in drivers/intel/fsp2_0/Kconfig when FSP_USE_REPO is selected.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I72faa6f9e5f2b06ab7cd43595ae0b49bf4d39630
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57349
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
The overrides set the options to the same value as drivers/intel/fsp2_0/
Kconfig does, so drop the overrides.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I53922786382a2e7d29b3df560a1998f41e1d2ea8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57350
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Normally, selecting FSP_USE_REPO will select FSP_FULL_FD which then will
configure the proper paths for FSP_M_FILE and FSP_S_FILE. The override
in these two boards caused FSP_M_FILE and FSP_S_FILE being empty despite
ADD_FSP_BINARIES being selected by FSP_USE_REPO which is an invalid case
that needs to be avoided, so remove the board-level override of those
two options.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I20c8cebea8327d59f0f33d05b824a74bf2121f4b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57347
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
The ADD_FSP_BINARIES override in the mainboard's Kconfig caused this
option to not be selected when FSP_USE_REPO is selected. Remove the
override to fix this problem. These two boards are the only ones in tree
that had an override for this option, so now the ADD_FSP_BINARIES option
is only defined in drivers/intel/fsp2_0/Kconfig.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I23439f3134eef9460625addbff7efd64c5f65ae5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57346
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
This option is neither selected nor usable for the only remaining SoC
that uses this code, so drop the remaining parts. configure_hudson_uart
isn't called anywhere and isn't even compiled, since it's guarded by an
#if CONFIG(HUDSON_UART) block and the HUDSON_UART Kconfig option isn't
selected anywhere. Both the offsets used in the iomux_write8 calls and
the UART controller itself aren't listed in the BKDG #52740 Rev 3.05 for
the AMD Family 16h Models 30h-3Fh APUs which is the only SoC that uses
this code, so the code didn't even apply for this chip.
TEST=Timeless build for pcengines/apu2 results in identical binary.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I3f462d1f83a0f1ba851329ebebb1f3263267fdc6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56785
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
This config selected ADD_FSP_BINARIES even though HAVE_INTEL_FSP_REPO is
only defined for Apollolake and not Geminilake that resides in the same
SoC directory and uses the same Kconfig file. This results in the paths
to the FSP binaries not being defined, in which case the
ADD_FSP_BINARIES option shouldn't be selected.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I95123c4930b44a3b76c87768e130eb7359bbf625
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57351
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Since the FSP binaries for Picasso are present in the amd_blobs repo,
select the ADD_FSP_BINARIES option if the Kconfig option to check out
that repo is set.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I9a8571730cf271ad5e113e5df87700882b3c5475
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57348
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
This patch ensures mp_run_on_all_aps() is passing 'MP_RUN_ON_ALL_CPUS'
macro rather hardcoding `0` while running `func` on all APs.
Change-Id: Icd34371c0d4349e1eefe945958eda957c4794707
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57342
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
EGPIO132 is the last documented GPIO on the GPIO controller in the NDA
version of the BKDG for AMD Family 16h Models 30h-3Fh Processors (#52740
Rev 3.06) which is the only SoC using this code, so define
SOC_GPIO_TOTAL_PINS as 133, since the internal GPIO numbers are
0-indexed. This definition will be needed the subsequent patch that'll
add the remote GPIO support to the common AMD GPIO code to make sure
that the compiler can optimize out the code path needed to support the
remote GPIO access which isn't available on this platform anyway.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I877d462c5e753c9bbb3461dbb10cde2adc2cb12c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56809
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
If a USB_MUX_EVENT happens while the AP is in S3 during powerdown
transtion (S0->S3->S5), this will cause the device to boot again after
it has finished sequencing down to S5. Since S3 is not POR for ChromeOS
devices anymore, change this event to wake from S3 and S0ix to just
S0ix.
BUG=b:197039097
TEST=abuild
Change-Id: I91e5e0ab8301377817875b6fa9e3c0e1f96c1465
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57341
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Zhuohao Lee <zhuohao@google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
Add NixOS configurations for bootable live systems containing a set of
tools which might be useful for firmware development in general and for
working on coreboot.
There are two configurations provided. One for console-only and a
graphical one, which is mostly the same as the console image but it
comes with Gnome Shell as window manager and some graphical tools in
addition.
An image can be built using `build-console.sh`, respectively
`build-graphical.sh`. The resulting iso image can be found in
`result/iso/`.
The console image results in ~700MB, while the graphical one results in
~2GB.
Change-Id: Iaf49d198e99781434bd89d2a8a125a4988b77e1c
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50194
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
This patch updates debug message to specifically the case when SMBIOS
table 7 write would abort due to either `unknown` CPU or CPU `doesn't
have support for deterministic cache cpuid leaf`.
Change-Id: I288593b3f78ab858bf66c689e7cfb6ba2ff746d0
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57337
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Don't attempt to fill the SMBIOS table if the CPU doesn't support
deterministic cache CPUID.
TEST=Able to fix the hang issue seen on ASRock E350M1 with commit hash
e2b5fee.
Change-Id: Id65dc963e235f7080370a32cf69bcc4bee94d28f
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57306
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Swift Geek (Sebastian Grzywna) <swiftgeek@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
`cpu_get_cache_info_leaf()` function is responsible to report leaf
value for CPU that have support for deterministic cache cpuid. As per
available datasheets from AMD and Intel the supported CPUID leafs are
0x8000_001d for AMD and 0x04 for Intel. Hence, this CL skips returning
default leaf value as `0`.
TEST=Verified fixes: e2b5fee3b006 (arch/x86: smbios write 7 table using
deterministic cache functions) hang issue on ASRock E350M1.
Change-Id: Iee33b39298e7821ac5280d998172b58a70c8715b
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57305
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Refactor Qcom QSPI driver to separate common
and SoC specific driver code.
BUG=b:182963902
TEST=Validated on qualcomm sc7280 development board
Signed-off-by: Rajesh Patil <rajpat@codeaurora.org>
Change-Id: Ibe1dc3fe8bd71957ff8604ef4c9d97963100ccfb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55322
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shelley Chen <shchen@google.com>
|
|
There are two different types of 682 SKU available with TDP
of 28W and 45W. This patch fix override values for power
limits for these 682 SKU. This patch also sets power limit
values dynamically based on machine ID and CPU TDP of SKU.
BUG=b:194745919
BRANCH=None
TEST=Build FW and test on brya0 board
Change-Id: I796e56321ae9c8312530a4b8986cd73a2245f5fa
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57290
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
copy existing QSPI driver from /soc/qualcomm/sc7180 to common folder.
This common QSPI driver works in master mode and provides read/write
operation for the slave devices like flash.
BUG=b:182963902
TEST=Validated on qualcomm sc7180 and sc7280 development board
Signed-off-by: Rajesh Patil <rajpat@codeaurora.org>
Change-Id: I5b3816b823e14db1dd13f1eb4a6761c7a61604b9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55323
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shelley Chen <shchen@google.com>
|
|
Introduce DDR One-Time-Training Support
Device reboots without training from second iteration
and also DDR training data is 32kb size, hence update
required in memlayout and to sync with upstream changes
the Fmap size even got bumped up.
BUG=b:182963902
TEST=Validated on qualcomm sc7280 development board
Change-Id: I81038c5c7802c154f4310509c6c64710580b8ce4
Signed-off-by: Sudheer Kumar Amrabadi <samrabad@codeaurora.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54352
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shelley Chen <shchen@google.com>
|
|
Configure 384MHz for eMMC clock and 50MHz for SD card clock.
BUG=b:182963902
TEST=Validated on qualcomm sc7280 development board
Change-Id: I8acbce58614add0228adc39289762da10937cbe2
Signed-off-by: Shaik Sajida Bhanu <sbhanu@codeaurora.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50585
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shelley Chen <shchen@google.com>
|
|
It supports the clock consumers for QUP, SDCC, PCIE, Display to be able
to configure & enable the desired clocks.
The clock driver also supports reset of subsystems like AOP and SHRM.
Also add support for Zonda PLL enable for CPU in common clock driver.
Refactor the SC7280 clock driver to use the common clock driver APIs.
BUG=b:182963902
TEST=Validated on qualcomm sc7280 development board
Change-Id: I590a93cda0d6eccb51b54692b620d43ccacede77
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50580
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Shelley Chen <shchen@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add TPM IRQ config to gpio_m.c, so the TPM IRQ is not allocated
to I2C4.
BUG=NA
BRANCH=None
TEST= boot to os and check cat /proc/interrupts, cr50 SPI interrupt is assigned
and does not conflict with I2C.
CPU0 CPU1 CPU2 CPU3 CPU4 CPU5 CPU6 CPU7 CPU8 CPU9 CPU10 CPU11
0: 36 0 0 0 0 0 0 0 0 0 0 0 IO-APIC 2-edge timer
1: 0 0 0 0 0 0 0 0 9 0 0 0 IO-APIC 1-edge i8042
8: 0 0 0 0 0 0 0 0 0 0 0 0 IO-APIC 8-edge rtc0
9: 0 0 0 0 0 0 0 0 0 0 0 0 IO-APIC 9-fasteoi acpi
14: 0 0 0 0 0 0 0 0 0 0 0 0 IO-APIC 14-fasteoi INTC1055:00
16: 0 0 0 0 0 0 0 0 0 0 4 0 IO-APIC 16-fasteoi intel-ipu6
22: 0 13 0 0 0 0 0 0 0 0 0 0 IO-APIC 22-fasteoi idma64.4, i801_smbus, ttyS0
37: 0 0 0 0 0 0 0 0 0 0 0 0 IO-APIC 37-fasteoi idma64.0, i2c_designware.0
38: 0 0 0 0 0 0 0 0 0 0 4 0 IO-APIC 38-fasteoi idma64.1, i2c_designware.1
41: 0 0 0 0 2274 0 0 0 0 0 0 0 IO-APIC 41-edge cr50_spi
42: 0 0 0 0 0 0 0 0 0 0 0 0 IO-APIC 42-fasteoi idma64.2, i2c_designware.2
43: 4 0 0 0 0 0 0 0 0 0 0 0 IO-APIC 43-fasteoi idma64.3, i2c_designware.3
Signed-off-by: Selma Bensaid <selma.bensaid@intel.com>
Change-Id: Id0f3885dec5a6f635254c233709090321491c739
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57102
Reviewed-by: Bora Guvendik <bora.guvendik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Set power limit values dynamically based on CPU TDP and PCI ID of SKU.
BUG=b:194745919
BRANCH=None
TEST=Build FW and test on brya0 board
Change-Id: Ic331a3debb076ef08a312a31edc1468974fd4902
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57035
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Get tdp value of CPU for different SKUs based on PKG POWER MSR.
BUG=b:194745919
BRANCH=None
TEST=Build FW and test on brya0 board
Change-Id: I9fba0a64da2f1d79d633054dddd9fdf1d3d8e258
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57143
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
|
|
Add GPIO IOMUX defines for the pins that are used in the mainboard code
which enables using the PAD_GPI and PAD_GPO macros.
TEST=Timeless build for APU2/3/4/5 results in identical binary.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ie32df9ed2cb6a5670a29cff91e085a3585c8bcf7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56836
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michał Żygowski <michal.zygowski@3mdeb.com>
|
|
southbridge/amd/pi/hudson uses the common GPIO bank access code from
soc/amd, but doesn't provide all functionality that would be needed to
use the full functionality. Add a Kconfig option that switches off some
functionality in the common SoC GPIO access code, so that more of the
functionality proviced by the common SoC GPIO code can be used in the
AMD binaryPI chipset and board code.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ib10d5d5580aab30a359aa001bb6fc7e9fdb8fc41
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56783
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The mapping of the package GPIO numbers to the GPIO numbers on the GPIO
controller isn't a 1:1 one, so add a comment about that to avoid
confusion. Also change the comment style to match the style guide.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ie30bf5483ea2e2516d7e3fdd21ea9338362e526e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56808
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michał Żygowski <michal.zygowski@3mdeb.com>
|
|
Also remove the unused amdblocks/acpimmio.h include in gpio_ftns.c.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: Michał Kopeć <michal.kopec@3mdeb.com>
Change-Id: If121941c8a6ba88913653192740997aeef426548
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56784
Reviewed-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Override DdiPortAConfig as MIPI DSI
BUG=b:192521391
BRANCH=None
TEST=Built test coreboot image and boot on bugzzy board
Change-Id: If308f9d69fea56176527e7b67f36b29c43adb525
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57107
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Henry Sun <henrysun@google.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Make adding the FSP-T file to CBFS depend on both ADD_FSP_BINARIES and
FSP_CAR Kconfig options being set. The FSP_T_FILE Kconfig option depends
on both, so also check if both are selected in the Makefile where it
tries to add the FSP-T to the CBFS.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Suggested-by: Furquan Shaikh <furquan@google.com>
Change-Id: Id347336f2751c6d871f31d89c30a1222037c2d69
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57220
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Remove unused drivers and some fast calibration implementations
to align with the latest MTK memory reference code.
Signed-off-by: Ryan Chuang <ryan.chuang@mediatek.corp-partner.google.com>
Change-Id: I3b235cbceb231898f00fce7905f596eab54ca595
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57275
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The clock driver supports configuring the general purpose PLLs,
configuring the root clock generator (RCG), enable clock branch, enable
gdsc and also the block resets.
The common clock driver exposes PLL configuration functions and also
different Agera PLL enable functions for the CPU PLLs.
While at it, the common driver also supports reset of subsystems like
AOP and SHRM.
SC7180 clock driver is also refactored to use the common clock
driver APIs.
BUG=b:182963902
TEST=Validated on qualcomm sc7180 and sc7280 development board.
Change-Id: I03d1b4a2fb90303c7259ec08f312d78b4e33ec39
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56588
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shelley Chen <shchen@google.com>
|
|
As we move to use the common clock driver, the sc7180 clock driver,
watchdog and display drivers requires few cleanups, thus update the
impacted drivers.
Earlier the display client is expected to provide 2n divider value,
as the divider value in register is in form "2n-1".
mdss_clk_cfg.div = half_divider ? (half_divider - 1) : 0;
The older convention in the upcoming patches would be replaced with
the common macro of QCOM_CLOCK_DIV, thus need the divider needs to
be updated.
mdss_clk_cfg.div = half_divider ? QCOM_CLOCK_DIV(half_divider) : 0;
To accommodate impacting the functionality, the half_divider is taken
care in the clock driver.
BUG=b:182963902
TEST=Validated on qualcomm sc7180 development board
Change-Id: Ic334fd0d43e5b4b1e43a27d5db7665f0bc151d66
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56587
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shelley Chen <shchen@google.com>
|
|
CONFIG_DRIVERS_INTEL_MIPI_CAMERA and CONFIG_SOC_INTEL_COMMON_BLOCK_IPU
are getting selected for all ADLRVPs irrespective of ADL-P and ADL-M
(internal and external EC SKUs) hence, select those Kconfigs from
mainboard Kconfig rather Kconfig.name.
Also, select DRIVERS_INTEL_SOUNDWIRE as per alphabetical order.
TEST=No changes are seen while the .config file is getting auto
generated.
Change-Id: I62d5ec19c3364da79ebe7287b1b3d6eb2a0efca0
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57314
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Set the `UserBd` FSP-M UPD to `BOARD_TYPE_DESKTOP` by default on PCH-H.
Remove now-redundant mainboard code to set the `UserBd` UPD.
Change-Id: I349abe5d89f562c158ce9baadbca2b2f56695846
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57261
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
SoC code already sets this UPD to `CONFIG_IED_REGION_SIZE`, which
defaults to 0x400000 for soc/intel/cannonlake.
Change-Id: I6587e17a4a3425c561cffe6e3df0d932a2458168
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57260
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
|
|
Change-Id: I291dc71bb6e3888b71ebce315f9ad09ccbc4a9a7
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57259
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
|
|
Specify the type of the `DIMM_MAX` Kconfig symbol once.
Change-Id: I2e86baaa8bd50c7b82c399fde5dcea05da6b4307
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57258
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Crawford <tcrawford@system76.com>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
|
|
Specify the type of the `DIMM_SPD_SIZE` Kconfig symbol once.
Change-Id: I619833dbce6d2dbe414ed9b37f43196b4b52730e
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57257
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
variant_has_pcie_wwan() was always coming back as disabled because
find_dev_nested_path() couldn't find the device until the domain was
added to the array.
BUG=b:193036827
TEST=Boot guybrush with PCIe & USB WWAN devices.
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: Id94fa0b0ff5c29fa447e869220d27ccfe61438c6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57315
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Change-Id: I0b1c29162a64030b5c100368f2471702e22b8311
Signed-off-by: Iru Cai <mytbk920423@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54744
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
The RW_MRC_CACHE only needs to be 64K for Brya.
BUG=none
TEST="emerge-brya coreboot chromeos-bootimage", flash and boot
brya0 to kernel.
Change-Id: I74365b795e184b92f483ae2bf862791e235c5362
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56989
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add support for DSM methods as per the connectivity document
559910_Intel_Connectivity_Platforms_BIOS_Guidelines_Rev6_4.pdf
BUG=b:191720858
TEST=Check the generated SSDT tables for DSM methods
Change-Id: Ie154edf188531fe6c260274edaa694cf3b3605d3
Signed-off-by: Sugnan Prabhu S <sugnan.prabhu.s@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56751
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
