summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2020-12-01mb/intel/adlrvp: Update GPIO configuration as per schematicsVarshit Pandya
Configure I2C related GPIO as per ADL-P schematics. This is based on Revision 0.974 of schematics. Signed-off-by: Varshit Pandya <varshit.b.pandya@intel.com> Change-Id: I76e1207cb31bed10b6e9fbeb2456b6feec42f97e Reviewed-on: https://review.coreboot.org/c/coreboot/+/47495 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: V Sowmya <v.sowmya@intel.com>
2020-12-01mainboard/intel/adlrvp: Enable PCH PCIe device over x1 slotSubrata Banik
List of changes: 1. Enable Root Port 8 aka 0:0x1c:7 2. Assign free running clock for RP8 3. Apply W/A to get card detected on x1 slot - Drive OEB 7:GPP_A7 and OEB 6:GPP_E5 low TEST=Able to detect PCIe SD card over x1 slot localhost ~ # dmesg | grep mmc [ 3.643755] mmc0: SDHCI controller on PCI [0000:02:00.0] using ADMA [ 3.825201] mmc0: new ultra high speed DDR50 SDHC card at address 17f8 [ 3.835452] mmcblk0: mmc0:17f8 SE16G 14.4 GiB [ 3.849158] mmcblk0: p1 Change-Id: Ibea37b8de4dd020ff0108ec90ea6f8bcfaa4fb17 Signed-off-by: Subrata Banik <subrata.banik@intel.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/48080 Reviewed-by: Angel Pons <th3fanbus@gmail.com> Reviewed-by: V Sowmya <v.sowmya@intel.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-12-01mainboard/intel/adlrvp/spd: Update SPD for LP4x SKUSubrata Banik
List of changes in SPD: 1. SPD Revision (of JEDEC spec) 2. SDRAM Maximum Cycle Time (tCKAVGmax) (MTB) 3. MSB -> CAS Latencies Supported, First Byte 4. CAS Latencies Supported, Second Byte 5. CAS Latencies Supported, Third Byte 6. LSB -> CAS Latencies Supported, Fourth Byte 7. Minimum CAS Latency Time (tAAmin) 8. Fine Offset for SDRAM Maximum Cycle Time (tCKAVGmax) 9. Fine Offset for SDRAM Minimum Cycle Time (tCKAVGmin) 10.Cyclical Redundancy Code (0- 125 byte) TEST=Able to build and boot with updated SPD. Change-Id: Iae7f2693e87bffb2dfa20bd07b22f4a4768c56cb Signed-off-by: Subrata Banik <subrata.banik@intel.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/48079 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: V Sowmya <v.sowmya@intel.com>
2020-12-01mb/intel/adlrvp: Add support for LPDDR5Sridhar Siricilla
This patch adds LPDDR5 memory configuration parameters to FSP. TEST=Able to pass FSP-M MRC training on LPDDR5 RVP. Signed-off-by: Sridhar Siricilla <sridhar.siricilla@intel.com> Change-Id: I787bf97dd6c244bd3b0662e5bd061a2da80baa90 Reviewed-on: https://review.coreboot.org/c/coreboot/+/46899 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Angel Pons <th3fanbus@gmail.com> Reviewed-by: V Sowmya <v.sowmya@intel.com>
2020-12-01mb/intel/adlrvp: Refactor lpddr4_mem_config structureSubrata Banik
List of changes: 1. Initialize dq_map array in a single line 2. Make dqs_map array also in a single line TEST=Able to build and boot ADLRVP LP4 SKU. Change-Id: I64f2b38492934c8ede301f4b252c8700060ed4ac Signed-off-by: Subrata Banik <subrata.banik@intel.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/48077 Reviewed-by: Angel Pons <th3fanbus@gmail.com> Reviewed-by: V Sowmya <v.sowmya@intel.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-12-01Makefile.inc: Alloc .bss* sections for "struct" file typeYu-Ping Wu
When the global variable of a "struct" CBFS file is zero (for example, CB:47696), the binary will appear in the .bss* section in the ELF file (instead of .data). This results in an empty binary file added to CBFS, so that file size check will fail when reading it at runtime. BUG=b:173751635 TEST=emerge-asurada coreboot TEST=Check sdram-lpddr4x-KMDP6001DA-B425-4GB is non-empty in CBFS BRANCH=none Change-Id: Idfd17d10101a948de0eb0522a672afd5c2f83b04 Signed-off-by: Yu-Ping Wu <yupingso@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/47903 Reviewed-by: Julius Werner <jwerner@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-12-01util/mb/google/puff: remove HECI from overridetreePaul Fagerburg
The template for overridetree.cb includes HeciEnabled, which has been removed from the CNL config struct, so remove it from the overridetree. BUG=b:174360951 TEST=`new_variant_fulltest.sh puff` succeeds Signed-off-by: Paul Fagerburg <pfagerburg@google.com> Change-Id: I87f67c53cc75d9ddd40b4960739180a95de6ecd6 Reviewed-on: https://review.coreboot.org/c/coreboot/+/48129 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
2020-11-30mb/siemens/chili: Configure GPIOs in gpio.cFelix Singer
Get rid of variant_gpio_table() and configure GPIOs in gpio.c instead of passing data around. Change-Id: Ib158d6bdbcbceb3c1dc4f47fc7c3e098b9c7e5c4 Signed-off-by: Felix Singer <felixsinger@posteo.net> Reviewed-on: https://review.coreboot.org/c/coreboot/+/47974 Reviewed-by: Michael Niewöhner <foss@mniewoehner.de> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-11-30mb/siemens/chili: Introduce include folder for header filesFelix Singer
Use include folder for header files allowing proper includes. Change-Id: I80066fb925b918d040062397e633c5d499a50dbe Signed-off-by: Felix Singer <felixsinger@posteo.net> Reviewed-on: https://review.coreboot.org/c/coreboot/+/47973 Reviewed-by: Michael Niewöhner <foss@mniewoehner.de> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-11-30mb/kontron/bsl6: Configure GPIOs using mainboard_opsFelix Singer
Hook up the mainboard_ops driver and configure the GPIOs using .init, since mainboard_silicon_init_params() is meant for the configuration of the FSP, not the GPIOs. Change-Id: I6ab8d258c6f81c90d835cb8d07c6387d3de76d85 Signed-off-by: Felix Singer <felixsinger@posteo.net> Reviewed-on: https://review.coreboot.org/c/coreboot/+/47850 Reviewed-by: Michael Niewöhner <foss@mniewoehner.de> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-11-30soc/intel/skylake: Fix commentFelix Singer
mainboard_silicon_init_params() is *not* meant for configuring GPIOs. It should only be used to configure FSP options, which can not be configured elsewhere. Change-Id: Ia92d0d173af9c67600e93b473480967304772998 Signed-off-by: Felix Singer <felixsinger@posteo.net> Reviewed-on: https://review.coreboot.org/c/coreboot/+/48008 Reviewed-by: Michael Niewöhner <foss@mniewoehner.de> Reviewed-by: Arthur Heymans <arthur@aheymans.xyz> Reviewed-by: Nico Huber <nico.h@gmx.de> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-11-30util/pgtblgen: Improve compatibilityPatrick Georgi
Fix build on Debian/jessie Change-Id: I987e7a03441b40ab06ccd54a21e38aac81a1c28d Signed-off-by: Patrick Georgi <pgeorgi@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/48004 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Martin Roth <martinroth@google.com>
2020-11-30soc/amd/picasso: remove PICASSO_LPC_IOMUX Kconfig option from SoCFelix Held
PICASSO_LPC_IOMUX was only used in the amd/mandolin board, but not in the corresponding SoC code, so remove it from the SoC's Kconfig and reanme it in the mainboard's Kconfig to MANDOLIN_LPC. Change-Id: I261e093d6c56be6073a816b79c60d3a0457616f8 Signed-off-by: Felix Held <felix-coreboot@felixheld.de> Reviewed-on: https://review.coreboot.org/c/coreboot/+/47891 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
2020-11-30soc/amd/picasso: remove unused AMDFW_OUTSIDE_CBFS Kconfig optionFelix Held
The corresponding functionality in the SoC's Makefile.inc was removed in commit ef3395d990bbf1118a8d4e367a986bdbc92b1820 Change-Id: Iba84d9deb155ce314b3a3588781752b83a21486b Signed-off-by: Felix Held <felix-coreboot@felixheld.de> Reviewed-on: https://review.coreboot.org/c/coreboot/+/47890 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
2020-11-30soc/amd: move bootblock inside main SoC directoriesFelix Held
There's no need to have the bootblock in its own sub-directory, so move it to each SoC's main directory to avoid clutter. This makes soc/amd more consistent with the coreboot code base in src/northbridge, src/southbridge and src/soc with the exception of src/soc/intel. Change-Id: I78a9ce1cd0d790250a66c82bb1d8aa6c3b4f7162 Signed-off-by: Felix Held <felix-coreboot@felixheld.de> Reviewed-on: https://review.coreboot.org/c/coreboot/+/47982 Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-11-30mb/google/volteer: Create drobit variantFrank Chu
Create the drobit variant of the volteer reference board by copying the template files to a new directory named for the variant. (Auto-Generated by create_coreboot_variant.sh version 4.2.0). BUG=b:171947885 BRANCH=none TEST=emerge-volteer coreboot Signed-off-by: Frank Chu <frank_chu@pegatron.corp-partner.google.com> Change-Id: I63b7312bba236bd5af028359804d042f6850d8ba Reviewed-on: https://review.coreboot.org/c/coreboot/+/47787 Reviewed-by: Zhuohao Lee <zhuohao@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-11-30soc/amd/common/vboot: use transfer_buffer_valid functionFelix Held
show_psp_transfer_info reimplemented the functionality of transfer_buffer_valid, so use replace that with a function call. Change-Id: Ie3d373b10bdb0ab00640dabeea12b13ec25406cc Signed-off-by: Felix Held <felix-coreboot@felixheld.de> Reviewed-on: https://review.coreboot.org/c/coreboot/+/47977 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Martin Roth <martinroth@google.com>
2020-11-30soc/amd: move vboot-on-PSP-related functions to common/vbootFelix Held
Change-Id: I4f07d3ab12116229a13d2e8c02b2deb06e51a1af Signed-off-by: Felix Held <felix-coreboot@felixheld.de> Reviewed-on: https://review.coreboot.org/c/coreboot/+/47976 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Martin Roth <martinroth@google.com>
2020-11-30soc/amd: move vboot bootblock functions to common folderFelix Held
Change-Id: I9e9fed26a686b8f90797687dd720902be48dae72 Signed-off-by: Felix Held <felix-coreboot@felixheld.de> Reviewed-on: https://review.coreboot.org/c/coreboot/+/47975 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Martin Roth <martinroth@google.com>
2020-11-30soc/amd: move assembly part of non-CAR bootblock to common directoryFelix Held
There will be more files added to the common non-CAR Makefile.inc, so use an ifeq statement there. Change-Id: I1f71954d27fbf10725387a0e95bc57f5040024cc Signed-off-by: Felix Held <felix-coreboot@felixheld.de> Reviewed-on: https://review.coreboot.org/c/coreboot/+/47880 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Martin Roth <martinroth@google.com>
2020-11-30soc/amd/common: introduce SOC_AMD_COMMON_BLOCK_PCI_MMCONFFelix Held
Add a Kconfig symbol for including the PCIe MMCONF setup function in the build and select it when SOC_AMD_COMMON_BLOCK_PCI is selected and in the southbridges call enable_pci_mmconf(), but don't select SOC_AMD_COMMON_BLOCK_PCI. Change-Id: I32de7450bff5b231442f9f2094a18ebe01874ee7 Signed-off-by: Felix Held <felix-coreboot@felixheld.de> Reviewed-on: https://review.coreboot.org/c/coreboot/+/47878 Reviewed-by: Martin Roth <martinroth@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-11-30drivers/intel/fsp2_0: Remove console in weak functionArthur Heymans
This pollutes the log on all platforms not implementing an override. Change-Id: I0d8371447ee7820cd8e86e9d3d5e70fcf4f91e34 Signed-off-by: Arthur Heymans <arthur@aheymans.xyz> Reviewed-on: https://review.coreboot.org/c/coreboot/+/48128 Reviewed-by: Frans Hendriks <fhendriks@eltan.com> Reviewed-by: Angel Pons <th3fanbus@gmail.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-11-30mb/google/dedede: Update Imon slope and Offset Value for DrawciaMeera Ravindranath
Updating Imon slope and offset values as per recommendation of ODM based on calibaration. Updating Imon slope to 1.0 and offset to 1.4 BUG=b:167294777 BRANCH=dedede TEST=Boot dedede platform and confirm values in FSP. Change-Id: I3eb32218040163f0abef9b8dd4c52efb16289fe7 Signed-off-by: Meera Ravindranath <meera.ravindranath@intel.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/48072 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Vinay Kumar <vinay.kumar@intel.com> Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
2020-11-30mb/google/dedede: Create sasuke variantRaymond Chung
Create the sasuke variant of the waddledoo reference board by copying the template files to a new directory named for the variant. (Auto-Generated by create_coreboot_variant.sh version 4.3.1). BUG=b:172104731 BRANCH=None TEST=util/abuild/abuild -p none -t google/dedede -x -a make sure the build includes GOOGLE_SASUKE Signed-off-by: Raymond Chung <raymondchung@ami.corp-partner.google.com> Change-Id: I29405d63fd266224807e535c3f86a2ad5ab8cdf3 Reviewed-on: https://review.coreboot.org/c/coreboot/+/48112 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Henry Sun <henrysun@google.com> Reviewed-by: SH Kim <sh_.kim@samsung.corp-partner.google.com> Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
2020-11-30lenovo/g505s: remove the unused and not present devicesMike Banon
Remove the devices unused or not present on this laptop. Signed-off-by: Mike Banon <mikebdp2@gmail.com> Change-Id: I0decad499dfbb5f1e0a189d21f0fca47c80bd490 Reviewed-on: https://review.coreboot.org/c/coreboot/+/47913 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
2020-11-30mb/google/volteer/variants/delbin: Enhance I2C5 bus freq closer 400 kHzFrank Chu
The current I2C5 bus frequency is 367 kHZ, which does not meet the spec. This change updates scl_lcnt, scl_hcnt, scl_hcnt value for I2C5 to bring the bus frequency closer to 400kHz. BUG=b:173670150 TEST=Verified that I2C5 frequency is between 386-387kHz. Signed-off-by: Frank Chu <frank_chu@pegatron.corp-partner.google.com> Change-Id: I6d60abe15645dc51ed9ee30975d2521b8940c2d0 Reviewed-on: https://review.coreboot.org/c/coreboot/+/47736 Reviewed-by: Zhuohao Lee <zhuohao@google.com> Reviewed-by: Zhuohao Lee <zhuohao@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-11-30soc/intel/alderlake: Add initial chipset.cbTim Wawrzynczak
Similar to the chipset.cb for TGL, this patch gives alias names to all of the published PCI devices. Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org> Change-Id: I6576ef4237c1fc8439795ad5b64b1840504edf73 Reviewed-on: https://review.coreboot.org/c/coreboot/+/48009 Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com> Reviewed-by: Subrata Banik <subrata.banik@intel.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-11-30include/device/pci_ids.h: Fix device id for gspi2Bora Guvendik
Device ID for "D18:F6 - GSPI #2" shoud be 0xA0FB BUG=none TEST=Boot to OS, verify SSDT Signed-off-by: Selma BENSAID <selma.bensaid@intel.com> Signed-off-by: Bora Guvendik <bora.guvendik@intel.com> Change-Id: I0d814170d24ff1b989eceb1d9ebdf6134df85e2e Reviewed-on: https://review.coreboot.org/c/coreboot/+/48060 Reviewed-by: Furquan Shaikh <furquan@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-11-30soc/intel/tigerlake: Add some helper macros for accessing TCSS DMA devicesTim Wawrzynczak
Change-Id: I6289d2049fbbb6bb532be3d9e2355c563ec98d1b Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org> Reviewed-on: https://review.coreboot.org/c/coreboot/+/47410 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
2020-11-30elog: Add new wake source codesTim Wawrzynczak
Tiger Lake introduces new wake-capable devices, including thunderbolt ports, TCSS XHCI & XDCI as well as DMA ports. Add new ELOG_WAKE_SOURCE macros for each of these types of devices. Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org> Change-Id: Ie5dae6514c2776b30418a390c4da53bda0b2d456 Reviewed-on: https://review.coreboot.org/c/coreboot/+/47395 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
2020-11-30util/docker/Makefile: Add missing separatorFrans Hendriks
Build using docker results in error: Makefile:86: *** missing separator. Add space after ifeq. Tested: Building Facebook FBG1701 binary. Change-Id: Ib42abe966e67dac380173ec982c9f6bd4cf074cc Signed-off-by: Frans Hendriks <fhendriks@eltan.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/47992 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Arthur Heymans <arthur@aheymans.xyz> Reviewed-by: Wim Vervoorn <wvervoorn@eltan.com> Reviewed-by: Angel Pons <th3fanbus@gmail.com>
2020-11-30mb/google/volteer/variant/copano: Add memory part supportNick Vaccaro
Add support for the following 5 LPDDR4x memory parts: - MT53E512M64D4NW-046 WT:E - H9HCNNNCRMBLPR-NEE - MT53D1G64D4NW-046 WT:A - H9HCNNNFBMBLPR-NEE - MT53D512M64D4NW-046 WT:F DRAM Part Name ID to assign ------------------------------------------- MT53E512M64D4NW-046 WT:E 0 (0000) H9HCNNNCRMBLPR-NEE 0 (0000) MT53D1G64D4NW-046 WT:A 1 (0001) H9HCNNNFBMBLPR-NEE 2 (0010) MT53D512M64D4NW-046 WT:F 0 (0000) BUG=b:172993397 TEST=none Change-Id: Iff8f6257c6cff77fc3f0bda7e75434f9f4de1777 Signed-off-by: Nick Vaccaro <nvaccaro@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/47981 Reviewed-by: Furquan Shaikh <furquan@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-11-30lp4x: Add new memory parts and generate SPDsNick Vaccaro
Add MT53D512M64D4NW-046 WT:F memory part to LP4x global list of available LP4x parts and to the global JSON file containing LP4x parts and their characteristics. BUG=b:172993397 TEST=none Change-Id: I09c6eab640c169dbdb451964967d14a31e314496 Signed-off-by: Nick Vaccaro <nvaccaro@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/47980 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Rob Barnes <robbarnes@google.com>
2020-11-30mb/prodrive/hermes: Use PCH_DEV_SMBUS definitionAngel Pons
This allows dropping ugly preprocessor usage from this file. Change-Id: Idb66d295129d98725f38d11ac162978418bd94c2 Signed-off-by: Angel Pons <th3fanbus@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/47959 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Patrick Georgi <pgeorgi@google.com>
2020-11-30mb/prodrive/hermes: Encapsulate GPIO setupAngel Pons
Having variants' gpio.c call the `gpio_configure_pads` function results in an API that does not need to pass data around, which is much simpler. Change-Id: I1064dc6258561bcf83f0e249d65b823368cf0d31 Signed-off-by: Angel Pons <th3fanbus@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/47958 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Felix Singer <felixsinger@posteo.net>
2020-11-30mb/prodrive/hermes: Use C-style commentsAngel Pons
Most of the existing comments are C-style already. Change-Id: I9ca4779f5b0560320e9bce4f33e54766522689f9 Signed-off-by: Angel Pons <th3fanbus@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/47957 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Felix Singer <felixsinger@posteo.net>
2020-11-30inteltool: Add support to print TME/MKTME statusPratik Prajapati
Print whether the SOC supports TME/MKTME. If the SOC supports the feature, print the status of enable and lock bit from TME_ACTIVATE MSR. -t option prints this status. Sample output: If TME/MKTME is supported: ============= Dumping INTEL TME/MKTME status ============= TME supported : YES TME locked : YES TME enabled : YES ==================================================== If TME/MKTME is not supported: ============= Dumping INTEL TME status ============= TME supported : NO ==================================================== Signed-off-by: Pratik Prajapati <pratikkumar.v.prajapati@intel.com> Change-Id: I584ac4b045ba80998d454283e02d3f28ef45692d Reviewed-on: https://review.coreboot.org/c/coreboot/+/45088 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2020-11-30soc/amd/common: add comments and FIXME to Makefile.inc filesFelix Held
Change-Id: Ie347ee508acd900353467b4a3e0a5d1928b110e1 Signed-off-by: Felix Held <felix-coreboot@felixheld.de> Reviewed-on: https://review.coreboot.org/c/coreboot/+/47877 Reviewed-by: Arthur Heymans <arthur@aheymans.xyz> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-11-30soc/amd/common: simplify conditionals in MakefilesFelix Held
If there are multiple statements that are conditional on the same Kconfig option, group them and move the condition check around the statement. If there's only one statement depending on one condition, use the short form instead. Change-Id: I89cb17954150c146ffc762d8cb2e3b3b374924de Signed-off-by: Felix Held <felix-coreboot@felixheld.de> Reviewed-on: https://review.coreboot.org/c/coreboot/+/47876 Reviewed-by: Arthur Heymans <arthur@aheymans.xyz> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-11-30soc/amd/common/block/cpu: move CAR-specific Makefile to sub-directoryFelix Held
Since there are sub-directories for both the cache-as-RAM case and the non-CAR case where the RAM is already initialized when the x86 cores are released from reset, move the CAR-specific parts of the Makefile.inc to another Makefile.inc in the car sub-directory. Further patches will add a Makefile.inc to the non-CAR directory. Change-Id: I43a3039237d96e02baa33488e71c5f24effe8359 Signed-off-by: Felix Held <felix-coreboot@felixheld.de> Reviewed-on: https://review.coreboot.org/c/coreboot/+/47875 Reviewed-by: Angel Pons <th3fanbus@gmail.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-11-30drivers/intel/i210: Request Bus Master in .final opsAngel Pons
Commit bd31642ad8 (intel/i210: Set bus master bit in command register) is only necessary because a buggy OS expects Bus Master to be set, not because the hardware requires Bus Master during initialization. It is thus safe to defer the Bus Master request into the .final callback. Change-Id: Iecfa6366eb4b1438fd12cd9ebb1a77ada97fa2f6 Signed-off-by: Angel Pons <th3fanbus@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/47401 Reviewed-by: Felix Held <felix-coreboot@felixheld.de> Reviewed-by: Felix Singer <felixsinger@posteo.net> Reviewed-by: Werner Zeh <werner.zeh@siemens.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Tested-by: siemens-bot
2020-11-30mb/siemens/mc_apl1: Deduplicate wait_for_legacy_dev()Angel Pons
There's one copy of this function for all variants except mc_apl4. Move one copy into common mainboard.c and exit early if running on mc_apl4. Change-Id: I4e35b58adc074831ccec433b8e014db0695b955e Signed-off-by: Angel Pons <th3fanbus@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/47402 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Patrick Georgi <pgeorgi@google.com>
2020-11-30mb/siemens/mc_apl1: Simplify is_mac_adr_valid() logicAngel Pons
A MAC address that is neither 00:00:00:00:00:00 nor ff:ff:ff:ff:ff:ff is considered valid. Instead of using a temporary buffer and memcmp(), use a single loop that exits as soon as the MAC cannot possibly be invalid. Change-Id: I2b15b510092860fbbefd150c9060da38aeb13311 Signed-off-by: Angel Pons <th3fanbus@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/47405 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Werner Zeh <werner.zeh@siemens.com> Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com> Reviewed-by: Uwe Poeche <uwe.poeche@siemens.com>
2020-11-30drivers/intel/i210: Define MAC_ADDR_LENAngel Pons
Define and use the MAC_ADDR_LEN macro in place of the `6` magic value. Change-Id: Icfa2ad9bca6668bea3d84b10f613d01e437ac6a2 Signed-off-by: Angel Pons <th3fanbus@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/47404 Tested-by: siemens-bot Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
2020-11-30mb/siemens/mc_apl1/mainboard.c: Refactor loop bodyAngel Pons
Break down multi-line compound conditions into multiple if-statements, and leverage `continue` statements to avoid nesting multiple checks. Change-Id: I5edc279a57e25a0dff1a4b42f0bbc88c0659b476 Signed-off-by: Angel Pons <th3fanbus@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/47403 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Tested-by: siemens-bot Reviewed-by: Werner Zeh <werner.zeh@siemens.com> Reviewed-by: Uwe Poeche <uwe.poeche@siemens.com>
2020-11-29mb/google/volteer: eldrid: use devtree aliases for PMC MUX connectorsScott Chao
Now that soc_get_pmc_mux_device() is gone, the PMC MUX connector devices can be hooked up together via devicetree aliases. BUG=b:172528109 BRANCH=firmware-volteer-13521.B TEST=built and USB3.0, type-c display work. Signed-off-by: Scott Chao <scott_chao@wistron.corp-partner.google.com> Change-Id: Iedf9b972b341064ff62a4443bfa83f69c8c60108 Reviewed-on: https://review.coreboot.org/c/coreboot/+/48066 Reviewed-by: Zhuohao Lee <zhuohao@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-11-29soc/intel: Configure P2SB before other PCH controllersFurquan Shaikh
This change updates bootblock_pch_early_init() to perform P2SB configuration before any other PCH controllers are initialized. This is done because the other controllers might perform PCR settings which requires the PCR base address to be configured. As the PCR base address configuration happens during P2SB initialization, this change moves the p2sb init calls before any other PCH controller initialization. BUG=b:171534504 Change-Id: I485556be003ff5338b4e2046768fe4f6d8a619a3 Signed-off-by: Furquan Shaikh <furquan@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/47885 Reviewed-by: Michael Niewöhner <foss@mniewoehner.de> Reviewed-by: Subrata Banik <subrata.banik@intel.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-11-29soc/intel/alderlake: Add lp5_ccc_config to the board memory configurationSridhar Siricilla
TEST=Able to pass LPDDR5 MRC training with Lp5CccConfig override. Signed-off-by: Sridhar Siricilla <sridhar.siricilla@intel.com> Change-Id: I24b1cf50c1b0b945fce75239bac38e40aeb8a83a Reviewed-on: https://review.coreboot.org/c/coreboot/+/47436 Reviewed-by: V Sowmya <v.sowmya@intel.com> Reviewed-by: Angel Pons <th3fanbus@gmail.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-11-29mb/intel/adlrvp: Disable dq_pins_interleaved for DDR4/5 RVPSubrata Banik
TEST=Able to pass MRC training on DDR4/5 SKUs Change-Id: I38fcb17a1be5a8544a17cef8255631b6abef0741 Signed-off-by: Subrata Banik <subrata.banik@intel.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/48078 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Sridhar Siricilla <sridhar.siricilla@intel.com> Reviewed-by: V Sowmya <v.sowmya@intel.com> Reviewed-by: Angel Pons <th3fanbus@gmail.com>
2020-11-29mb/supermicro/x11-lga1151-series: set FADT PM profile to ENTERPRISE_SERVERMichael Niewöhner
Set the FADT PM profile to ENTERPRISE_SERVER, since the currently supported X11 boards are server boards. Signed-off-by: Michael Niewöhner <foss@mniewoehner.de> Change-Id: I8fb5c7c262fbd3f3c085d7c2e2ef3d6ff6ce73eb Reviewed-on: https://review.coreboot.org/c/coreboot/+/48088 Reviewed-by: Patrick Rudolph <siro@das-labor.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-11-29mb/supermicro/x11-lga1151-series: rework gpio setup to not use headersMichael Niewöhner
Rework gpio setup for the board series to not use headers but stage-specific compilation units. Tested successfully on X11SSM-F. Signed-off-by: Michael Niewöhner <foss@mniewoehner.de> Change-Id: Ic62ce4335af605c081ef288e892441585ff2bd3e Reviewed-on: https://review.coreboot.org/c/coreboot/+/48087 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Felix Singer <felixsinger@posteo.net>
2020-11-29mb/supermicro/x11-lga1151-series: switch from dev.init to mb_ops.initMichael Niewöhner
GPIO needs to be initialized before the IPMI device gets initialized, so the GPIOs can be read/set by the code in CB:48096 and CB:48094. Thus, use mainboard_ops.init for GPIO configuration instead of using the indirection via a mainboard_enable function. To make it more visible, that we use chip.init, rename `mainboard_init` to `mainboard_chip_init`. Tested successfully on X11SSM-F including the IPMI changes. Signed-off-by: Michael Niewöhner <foss@mniewoehner.de> Change-Id: I192e69a34fa262b38bc40a95fb11c22a4041d0ae Reviewed-on: https://review.coreboot.org/c/coreboot/+/48083 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
2020-11-28mb/supermicro/x11ssm-f: drop unneeded ITSS overrideMichael Niewöhner
The ITSS override is not needed for LPC_CLKOUT* pads. Drop it. Signed-off-by: Michael Niewöhner <foss@mniewoehner.de> Change-Id: I3dbbc8944751779151dcd4f92fb870d937801d69 Reviewed-on: https://review.coreboot.org/c/coreboot/+/48084 Reviewed-by: Arthur Heymans <arthur@aheymans.xyz> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-11-28mb/supermicro/x11-lga1151-series: configure gpios in mainboard initMichael Niewöhner
Move gpio configuration from the Fsp callback to mainboard init. Tested successfully on X11SSM-F. Signed-off-by: Michael Niewöhner <foss@mniewoehner.de> Change-Id: If2a54c75c5243d94cdc025c597ee347820b35d32 Reviewed-on: https://review.coreboot.org/c/coreboot/+/48086 Reviewed-by: Felix Singer <felixsinger@posteo.net> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-11-28mb/supermicro/x11-lga1151-series: restructure and clean up devicetreeMichael Niewöhner
Drop zero-value devicetree options and move PcieRpEnable options down to the corresponding devices. Test: built with TIMELESS=1; binaries remain identical Signed-off-by: Michael Niewöhner <foss@mniewoehner.de> Change-Id: I9285d786e973621a732e2627c734adc930e54207 Reviewed-on: https://review.coreboot.org/c/coreboot/+/48082 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Felix Singer <felixsinger@posteo.net> Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
2020-11-28soc/intel/skl: correct OC pin skip value for disabled usb portsMichael Niewöhner
Commit 056d552 introduced a bug where 0xFF gets set as OC pin value to supposedly skip programming an OC pin for a disabled USB port. While the value is correct for the other platforms, Skylake uses 0x08 for this purpose. Correct this by using the enum value OC_SKIP (0x08) instead. Change-Id: I41a8df3dce3712b4ab27c4e6e10160b2207406d1 Signed-off-by: Michael Niewöhner <foss@mniewoehner.de> Reviewed-on: https://review.coreboot.org/c/coreboot/+/48003 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Felix Singer <felixsinger@posteo.net>
2020-11-27docs/mb/supermicro/x11-lga-series: Update documentationMichael Niewöhner
- Drop issue about non-working TianoCore with Aspeed NGI. see CB:35726 - Add missing reference to X11SSH-F - Drop TODO reference; there are no TODOs left Change-Id: I5becfa9ea01a0d9d651c6b51b30ebfcedb6412a5 Signed-off-by: Michael Niewöhner <foss@mniewoehner.de> Reviewed-on: https://review.coreboot.org/c/coreboot/+/48101 Reviewed-by: Patrick Rudolph <siro@das-labor.org> Reviewed-by: Felix Singer <felixsinger@posteo.net> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-11-27{docs/,}mb/supermicro/x11ssh-tf: drop TODO sectionMichael Niewöhner
Drop the TODO comment, since there is no TODO left. Also drop the now obsolete TODO section from the board documentation. Change-Id: I4192aaedc1429c8ff1bd7c52baa4741e1df0d0c5 Signed-off-by: Michael Niewöhner <foss@mniewoehner.de> Reviewed-on: https://review.coreboot.org/c/coreboot/+/48126 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Arthur Heymans <arthur@aheymans.xyz> Reviewed-by: Felix Singer <felixsinger@posteo.net>
2020-11-27docs/mb/supermicro/x11ssm-f: Update board documentationMichael Niewöhner
- Drop vanished issue on PCIe warning - Drop TODO section, since the TODOs are done - Document the jumper J6, that was not documented by the vendor. Its function has been determined by dissecting a dead board. - The flash is not socketed anymore. Drop that note and compress the whole paragraph. Also add a note about flashing via the BMC web interface. Change-Id: I2b5a08a6b6d80717621d6a30f31829fe4b84891a Signed-off-by: Michael Niewöhner <foss@mniewoehner.de> Reviewed-on: https://review.coreboot.org/c/coreboot/+/48125 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Arthur Heymans <arthur@aheymans.xyz> Reviewed-by: Felix Singer <felixsinger@posteo.net>
2020-11-27Makefile.inc: Move adding mcu FIT entriesArthur Heymans
This can be done using in the INTERMEDIATE target in the proper place. Change-Id: I28a7764205e0510be89c131058ec56861a479699 Signed-off-by: Arthur Heymans <arthur@aheymans.xyz> Reviewed-on: https://review.coreboot.org/c/coreboot/+/46453 Reviewed-by: Michael Niewöhner <foss@mniewoehner.de> Reviewed-by: Christian Walter <christian.walter@9elements.com> Reviewed-by: Angel Pons <th3fanbus@gmail.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-11-27soc/intel/jasperlake: Enable VT-d and generate DMAR TableMeera Ravindranath
Update UPDs required for the creation of DMAR table. By default coreboot was not generating DMAR table for IOMMU which was resulting in below error message in kernel: DMAR: [Firmware Bug]: No DRHD structure found in DMAR table DMAR: No DMAR devices found These changes will publish DMAR table through ACPI and will not result in the above error. BUG=b:170261791 BRANCH=dedede TEST=Build Dedede, boot to kernel and check dmesg if DMAR table exists. Signed-off-by: Meera Ravindranath <meera.ravindranath@intel.com> Change-Id: I97a9f2df185002a4e58eaa910f867acd0b97ec2b Reviewed-on: https://review.coreboot.org/c/coreboot/+/47506 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Karthik Ramasubramanian <kramasub@google.com> Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
2020-11-26util/inteltool: drop OS-specific rdmsr/wrmsr prototypesIdwer Vollering
The previous commit (that was not touching inteltool.h) marking internal functions as static is commit 6faccd1f00 Tested on: FreeBSD 13.0-CURRENT r355582 Change-Id: I4aba72f39b528fd70451a4656fd6c835ff766e49 Signed-off-by: Idwer Vollering <vidwer@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/37767 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Jacob Garber <jgarber1@ualberta.ca> Reviewed-by: Angel Pons <th3fanbus@gmail.com>
2020-11-26drivers/intel/fsp2_0: move the FSP FD PATH option down in menuconfigMichael Niewöhner
Move the FSP FD PATH option down, so it gets shown in place of the split FD files, when the users chooses to use a full FD binary. Change-Id: Ie03a418fab30a908d020abf94becbaedf54fbb99 Signed-off-by: Michael Niewöhner <foss@mniewoehner.de> Reviewed-on: https://review.coreboot.org/c/coreboot/+/47999 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
2020-11-26drivers/intel/fsp2_0: introduce possibility of using a full FD binaryMichael Niewöhner
Currently, setting a custom FSP binary is only possible by using split FSP-T/M/S FD files. This change introduces the possibility to pass a combined FD file (the "standard" FSP format). This is done by adding a new boolean Kconfig FSP_FULL_FD, specifying that the FSP is a single FD file instead of split FSP-T/M/S FD files, and making FSP_FD_PATH user-visible when the option is chosen. In this case, the other options for split files get hidden. When the user chooses to use a full FD file instead of the split ones, the FD file gets split during build, just like it is done when selecting the Github FSP repo (FSP_USE_REPO). Test: Supermicro X11SSM-F builds and boots fine with custom FSP FD set. Signed-off-by: Michael Niewöhner <foss@mniewoehner.de> Change-Id: I1cb98c1ff319823a2a8a95444c9b4f3d96162a02 Reviewed-on: https://review.coreboot.org/c/coreboot/+/47993 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
2020-11-26vc/intel/fsp/fsp2_0/alderlake: Update FSP header file version to 1483_11Subrata Banik
List of changes: 1. FSP-M Header: - Adjust UPD Offset for Reservedxx - Rename UPD Offset UnusedUpdSpace32 -> UnusedUpdSpace29 2. FSP-S Header: - Rename UPD Offset UnusedUpdSpace46 -> UnusedUpdSpace44 Change-Id: Ia1ef59e4cf6ccce8f48908af51535aea761cd972 Signed-off-by: Subrata Banik <subrata.banik@intel.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/47901 Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org> Reviewed-by: V Sowmya <v.sowmya@intel.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-11-25mb/google/dedede: Create galtic variantFrankChu
Create the galtic variant of the waddledee reference board by copying the template files to a new directory named for the variant. (Auto-Generated by create_coreboot_variant.sh version 4.3.1). BUG=b:170913840 BRANCH=None TEST=util/abuild/abuild -p none -t google/dedede -x -a make sure the build includes GOOGLE_GALTIC Signed-off-by: FrankChu <Frank_Chu@pegatron.corp-partner.google.com> Change-Id: Ie7534d56bc67aca4484f40af1221d669addc01fd Reviewed-on: https://review.coreboot.org/c/coreboot/+/47900 Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org> Reviewed-by: Martin Roth <martinroth@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-11-25mb/google/volteer: Update Eldrid USB2 port settings in overridetreeNick Chen
1. Disable M.2 WWAN and Type-A Port A1 2. Change register 4 to 3 and tuning USB2 Port1 eye diagram 3. Lower camera driving BUG=b:169105751 Signed-off-by: Nick Chen <nick_xr_chen@wistron.corp-partner.google.com> Change-Id: I6b8a5c0d5e814de232d79a43354f5ec0220fc5ea Reviewed-on: https://review.coreboot.org/c/coreboot/+/47863 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
2020-11-25Update vboot submodule to upstream masterPatrick Georgi
Updating from commit id 9d4053d: 2020-11-20 01:51:08 +0000 - (Revert "Reland: Clean up implicit fall through.") to commit id 48195e5: 2020-11-24 10:23:45 +0000 - (Makefile: Test for warning flags before using them) This brings in 3 new commits. Change-Id: I64f27f346df264cb6eeeb4e3203fcca7d35f7e83 Signed-off-by: Patrick Georgi <pgeorgi@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/47906 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Idwer Vollering <vidwer@gmail.com>
2020-11-25util/crossgcc: ensure curl writes downloaded bytes to a fileIdwer Vollering
Commit 82a30a134c (util/crossgcc: Retry package downloads on failure) caused a regression for curl users. Signed-off-by: Idwer Vollering <vidwer@gmail.com> Change-Id: I0d946b86baad3f6409a5042701808da307e5bcb7 Reviewed-on: https://review.coreboot.org/c/coreboot/+/47911 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Patrick Georgi <pgeorgi@google.com> Reviewed-by: Angel Pons <th3fanbus@gmail.com>
2020-11-25mb/ocp/deltalake: Define SMBIOS type 16 error correction type byTim Chu
RasModesEnabled Use RasModesEnabled from SystemMemoryMapHob to define SMBIOS type 16 error correction type Tested=Execute "dmidecode -t 16" to check if error correction type is correct. Signed-off-by: Tim Chu <Tim.Chu@quantatw.com> Change-Id: I3636fcc4a874261cf484c10e2db15015ac5d7e68 Reviewed-on: https://review.coreboot.org/c/coreboot/+/47509 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Jonathan Zhang <jonzhang@fb.com>
2020-11-25arch/x86/smbios: Update SMBIOS type 16 error correction typeTim Chu
Add weak function for SMBIOS type 16 error correction type. Tested=Execute "dmidecode -t 16" to check if error correction type is correct. Signed-off-by: Tim Chu <Tim.Chu@quantatw.com> Change-Id: I85b37e9cfd22a78544d03e5506ff92b1f2404f8e Reviewed-on: https://review.coreboot.org/c/coreboot/+/47508 Reviewed-by: Patrick Georgi <pgeorgi@google.com> Reviewed-by: Jonathan Zhang <jonzhang@fb.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-11-25mb/google/hatch: select SOC_INTEL_CSE_LITE_SKU only if CHROMEOSMatt DeVillier
Selecting SOC_INTEL_CSE_LITE_SKU without conditioning on CHROMEOS force-selects CHROMEOS, per src/soc/intel/common/block/cse/Kconfig. Conditioning on CHROMEOS allows for non-ChromeOS targets to be built. Test: build wyvern variant with CONFIG_CHROMEOS=n Change-Id: I61c9c78a3b02d64bab2813b7a80915b7ecf7f934 Signed-off-by: Matt DeVillier <matt.devillier@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/47725 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org> Reviewed-by: Angel Pons <th3fanbus@gmail.com>
2020-11-25cbfstool: Don't add compression attribute for uncompressed filesJulius Werner
Our current cbfstool has always added a compression attribute to the CBFS file header for all files that used the cbfstool_convert_raw() function (basically anything other than a stage or payload), even if the compression type was NONE. This was likely some sort of oversight, since coreboot CBFS reading code has always accepted the absence of a compression attribute to mean "no compression". This patch fixes the behavior to avoid adding the attribute in these cases. Change-Id: Ic4a41152db9df66376fa26096d6f3a53baea51de Signed-off-by: Julius Werner <jwerner@chromium.org> Reviewed-on: https://review.coreboot.org/c/coreboot/+/46835 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2020-11-25soc/intel/{broadwell,quark}: Drop `PEI_DATA` typedefAngel Pons
It is not used. Change-Id: I3ef0878811bf2ec406ded03aac6c5dfeb5bf45a2 Signed-off-by: Angel Pons <th3fanbus@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/47001 Reviewed-by: Frans Hendriks <fhendriks@eltan.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-11-25crossgcc: Upgrade binutils to 2.35.1Elyes HAOUAS
Change-Id: I8694a154d48c5a718b27d4beb858942db0feb997 Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/c/coreboot/+/45550 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2020-11-25crossgcc: Upgrade LLVM to version 11.0.0Elyes HAOUAS
Change-Id: I1cc02355e3fea7eb9ad98be6396a492dbbdc47b2 Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/c/coreboot/+/46379 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
2020-11-25mb/google/volteer/variant/lindar: change speaker smart amplifier to ALC1011Stanley Wu
Lindar change amp to ALC1011 Add ALC1011 amp acpi info to devicetree BUG=b:171771736 BRANCH=firmware-volteer-13521.B TEST=build and verify ALC1011 can be recognized. Change-Id: I4d83a19b3baa87cc926bb7c3a2cb96bf3165d2f4 Signed-off-by: Stanley Wu <stanley1.wu@lcfc.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/47009 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Zhuohao Lee <zhuohao@google.com> Reviewed-by: Caveh Jalali <caveh@chromium.org>
2020-11-25tests: Add lib/list-test test caseJakub Czapiga
Change-Id: If74f241b2bb788b3e2fd1b9062fc74819f7be31e Signed-off-by: Jakub Czapiga <jacz@semihalf.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/47507 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
2020-11-25MAINTAINERS: Add maintainers for kontron/mal10Felix Singer
Add Maxim Polyakov, Nico Huber and Felix Singer as maintainers for kontron/mal10. Change-Id: I2f4200708e4aec6d74916fb5e63efe2f20594882 Signed-off-by: Felix Singer <felixsinger@posteo.net> Reviewed-on: https://review.coreboot.org/c/coreboot/+/47889 Reviewed-by: Maxim Polyakov <max.senia.poliak@gmail.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-11-25mb/amd/mandolin: Add decode range for LPC debug cardNikolai Vyssotski
Some LPC debug boards hard strap SIO address to be at 0x164e/0x164d vs 0x4e/0x4d. Add support for configurable SIO address to support these cards. BUG=b:159933344 TEST=boot with LPC debug card, verify serial output Change-Id: I103c61f21f13970dfa3b9a788b29964e478fb84c Signed-off-by: Nikolai Vyssotski <nikolai.vyssotski@amd.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/47545 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
2020-11-25mb/google/volteer/var/elemi: Add H5ANAG6NCJR-XNCWisley Chen
Add H5ANAG6NCJR-XNC. BUG=b:165461530 BRANCH=volteer TEST=emerge-volteer coreboot Change-Id: I827158ce0abe764f1e3b5de46abf50dc148a6ff0 Signed-off-by: Wisley Chen <wisley.chen@quanta.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/47855 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
2020-11-25nb/amd: Deduplicate nb_common.hAngel Pons
Save for the IO_APIC2_ADDR definition, they are equivalent. Change-Id: I14da3d9aeefcc725428957ce0c9ac164eabacec6 Signed-off-by: Angel Pons <th3fanbus@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/47408 Reviewed-by: Arthur Heymans <arthur@aheymans.xyz> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-11-25device: Drop unused HyperTransport codeAngel Pons
Only two definitions are actually used somewhere, the rest is unused. Change-Id: Iec52d0d47fce6a1ec5455b670824b995a7a34a4c Signed-off-by: Angel Pons <th3fanbus@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/47407 Reviewed-by: Arthur Heymans <arthur@aheymans.xyz> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-11-24mb/clevo/kbl-u: Configure GPIOs using mainboard_opsFelix Singer
Hook up the mainboard_ops driver and configure the GPIOs using .init, since mainboard_silicon_init_params() is meant for the configuration of the FSP, not the GPIOs. Change-Id: I82f1eaf6693d9b117fb211776047058cdc787288 Signed-off-by: Felix Singer <felixsinger@posteo.net> Reviewed-on: https://review.coreboot.org/c/coreboot/+/47825 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
2020-11-24mb/kontron/bsl6: Move GPIO configuration to C fileFelix Singer
Change-Id: I008de1bf91ba97ee5eefbde11947c73059fff5f7 Signed-off-by: Felix Singer <felixsinger@posteo.net> Reviewed-on: https://review.coreboot.org/c/coreboot/+/47851 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Nico Huber <nico.h@gmx.de> Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
2020-11-24mb/kontron/bsl6: Use include folder for header filesFelix Singer
Change-Id: Id73a7385f7701920efebaa3e293ac50a6ba93272 Signed-off-by: Felix Singer <felixsinger@posteo.net> Reviewed-on: https://review.coreboot.org/c/coreboot/+/47849 Reviewed-by: Nico Huber <nico.h@gmx.de> Reviewed-by: Michael Niewöhner <foss@mniewoehner.de> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-11-24sb/intel/lynxpoint: Replace hard-coded IDs with definesFelix Singer
Replace hard-coded IDs with defines introduced in CB:47807. Used documents: - 328904-003 - 329003-003 Built lenovo/t440p with BUILD_TIMELESS=1, coreboot.rom remains identical. Change-Id: I910ab356dd8728c316018989bfb2689d4c67c2dc Signed-off-by: Felix Singer <felixsinger@posteo.net> Reviewed-on: https://review.coreboot.org/c/coreboot/+/47808 Reviewed-by: Michael Niewöhner <foss@mniewoehner.de> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-11-24include/device/pci_ids.h: Add PCI IDs used in Lynxpoint chipsetsFelix Singer
Used documents: - 328904-003 - 329003-003 Change-Id: I95790cda6f7c42a9de57bf5e92eb829ee1807dbe Signed-off-by: Felix Singer <felixsinger@posteo.net> Reviewed-on: https://review.coreboot.org/c/coreboot/+/47807 Reviewed-by: Michael Niewöhner <foss@mniewoehner.de> Reviewed-by: Angel Pons <th3fanbus@gmail.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-11-24mb/**/cmos.layout: Drop copy-pasted `volume` entriesAngel Pons
This option only applies to boards using the Lenovo H8 EC code. Change-Id: I3b16a61a0aa9f51a4061b1b5e58fc276e7383415 Signed-off-by: Angel Pons <th3fanbus@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/47150 Reviewed-by: Michael Niewöhner <foss@mniewoehner.de> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-11-24mb/**/cmos.layout: Drop copy-pasted SNB entries on non-SNBAngel Pons
Only Sandy Bridge MRC stores scrambler seeds in CMOS. Non-Sandybridge boards ended up with these entries because of copy-paste programming. Change-Id: I5a5bda6ea4e63ba03a4219bb2a6aa546bb6ecd7a Signed-off-by: Angel Pons <th3fanbus@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/47149 Reviewed-by: Michael Niewöhner <foss@mniewoehner.de> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-11-24mb/google/volteer/var/voxel: Update DPTF parametersSheng-Liang Pan
update the DPTF parameters received from the thermal team. BUG=b:167523658 TEST=emerge-volteer coreboot Signed-off-by: Pan Sheng-Liang <sheng-liang.pan@quanta.corp-partner.google.com> Change-Id: Iafc3fb389ade5cfec79a816a28880262bdce7c74 Reviewed-on: https://review.coreboot.org/c/coreboot/+/47858 Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org> Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-11-24soc/intel/xeon_sp: Enable SMI handlerRocky Phagura
SMI handler was not installed for Xeon_sp platforms. This enables SMM relocation and SMI handling. TESTED: - SMRR are correctly set - The save state revision is correct (0x00030101) - SMI's are properly generated and handled - SMM MSR save state are not supported, so relocate SMM on all cores in series - Verified on OCP/Deltalake mainboard. NOTE: - Code for accessing a CPU save state is not working for SMMLOADERV2, so some SMM features like GSMI, SMMSTORE, updating the ACPI GNVS pointer are not supported. - This hooks up to some soc/intel/common like TCO and ACPI GNVS. GNVS is broken and needs to be fixed separately. It is unknown if TCO is supported. This might require a cleanup in the future. Change-Id: Iabee5c72f0245ab988d477ac8df3d8d655a2a506 Signed-off-by: Rocky Phagura <rphagura@fb.com> Signed-off-by: Christian Walter <christian.walter@9elements.com> Signed-off-by: Arthur Heymans <arthur@aheymans.xyz> Reviewed-on: https://review.coreboot.org/c/coreboot/+/46231 Reviewed-by: Angel Pons <th3fanbus@gmail.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-11-24soc/intel/xeon_sp: Select INTEL_COMMON_BLOCK_TCOArthur Heymans
TCO is configured by FSP. This mostly makes it possible to report TCO events in SMM if enabled. Change-Id: I4f81c7888e45ed01ee68b1d6e6a9986a4d735467 Signed-off-by: Arthur Heymans <arthur@aheymans.xyz> Reviewed-on: https://review.coreboot.org/c/coreboot/+/47764 Reviewed-by: Angel Pons <th3fanbus@gmail.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-11-24soc/intel/xeon_sp: Hook up the PMC driverArthur Heymans
The soc code was already there but it was never linked. Change-Id: I75ee08dab524bc40f1630612f93cbd42025b6d4e Signed-off-by: Arthur Heymans <arthur@aheymans.xyz> Reviewed-on: https://review.coreboot.org/c/coreboot/+/47763 Reviewed-by: Angel Pons <th3fanbus@gmail.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-11-24mb/google/volteer: fw_config: Add setting for new sd readersZhuohao Lee
This patch adds three settings for the new sd readers. The new assigned values are: 1. RTS5227S: 3 2. L9750: 4 3. SD_OZ711LV2LN: 5 BUG=b:173676531 BRANCH=volteer TEST=abuild -t google/volteer Change-Id: I595695f99d3298f146fcdb7c2b942ce007ae9327 Signed-off-by: Zhuohao Lee <zhuohao@chromium.org> Reviewed-on: https://review.coreboot.org/c/coreboot/+/47856 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Caveh Jalali <caveh@chromium.org>
2020-11-24soc/intel/skylake: Support NHLT 1ch DMICBenjamin Doron
Allows advertising support for a 1ch array DMIC in the NHLT table. Boards use the NHLT if a microphone is connected to the DSP. Tested on an Acer Aspire VN7-572G (Skylake-U) on Windows 10. A custom ALSA topology will be required for Linux. Change-Id: Idba3a714faab5ca1958de7dcfc0fc667c60ea7fd Signed-off-by: Benjamin Doron <benjamin.doron00@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/43072 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Angel Pons <th3fanbus@gmail.com>
2020-11-24soc/intel/skylake: Use correct NHLT_PDM_DEV definitionBenjamin Doron
According to the NHLT specification[1], PDM_DEV is defined as "1" on Kabylake based platforms. coreboot currently sets it to "0" on all platforms. Add an entry to the enum and use it to define NHLT_PDM_DEV for Kabylake. "Device Type" will resume from "2" on all platforms, but entries are currently reserved. Tested on an Acer Aspire VN7-572G (Skylake-U), which has a 1ch array DMIC, on Windows 10. 1. https://01.org/sites/default/files/595976_intel_sst_nhlt.pdf Change-Id: Ifbc67228c9e7af7db5154d597ca8d67860cfd2ed Signed-off-by: Benjamin Doron <benjamin.doron00@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/45010 Reviewed-by: Angel Pons <th3fanbus@gmail.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2020-11-23nb/amd/agesa/family15tn: define macros for GNB and IOMMU devicesMike Banon
Follow the example of newer AMD code for Stoneyridge and Picasso. Signed-off-by: Mike Banon <mikebdp2@gmail.com> Change-Id: I9c17d4cb4953b28a47483f5d7db308ccc89e9281 Reviewed-on: https://review.coreboot.org/c/coreboot/+/47848 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Felix Held <felix-coreboot@felixheld.de> Reviewed-by: Angel Pons <th3fanbus@gmail.com>
2020-11-23nb/amd/agesa/family15tn: define macro for internal HDMI audio controllerMike Banon
Following the example of CB:7630 done for family16kb boards (git commit 3ff4f85ccd9fdb7cd4885a10f025b5ab297a445f). Signed-off-by: Mike Banon <mikebdp2@gmail.com> Change-Id: Ic48c7475ceadb60f825ca9e3c3427c8a7525a266 Reviewed-on: https://review.coreboot.org/c/coreboot/+/46589 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Felix Held <felix-coreboot@felixheld.de> Reviewed-by: Angel Pons <th3fanbus@gmail.com>
2020-11-23mb/google/zork: correct USB2 phy TXVREFTUNE0 parameter nameKevin Chiu
From spec, [31:28] "HS DC Voltage Level Adjustment" is "TXVREFTUNE0". correct rx_vref_tune -> tx_vref_tune BUG=None BRANCH=zork TEST=emerge-zork coreboot Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com> Change-Id: I27003a952d8f8bdd8fe52af8a37010e23ee9cdfd Reviewed-on: https://review.coreboot.org/c/coreboot/+/47735 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
generated by cgit v1.2.3 (git 2.25.1) at 2024-12-23 10:19:23 +0000