| Age | Commit message (Collapse) | Author |
|---|
|
Remove the UPD parameters to match QuarkFsp code.
TEST=Build and run on Galileo Gen2
Change-Id: Ie4639d1f087cc2bc4387aa691eb66b640fe8faf9
Signed-off-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-on: https://review.coreboot.org/14451
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
The BSP and AP callback declarations both had an optional argument
that could be passed. In practice that functionality was never used
so drop it.
Change-Id: I47fa814a593b6c2ee164c88d255178d3fb71e8ce
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/14556
Tested-by: build bot (Jenkins)
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Leroy P Leahy <leroy.p.leahy@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
The skylake-based Chromebooks use a separate verstage which runs
just after bootblock and prior to romstage. However, that
config is not enabled for coreboot.org so when
C_ENVIRONMENT_BOOTBLOCK changes were done it wasn't observed
that the Chromebook config failed because 2 _start symbols
were present. Remedy this failure by using the common
car_stage_entry symbol for taking over control flow.
Change-Id: I3f29b90ba8e3786b2106a34e49e6d1f9831dcc7c
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/14549
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Andrey Petrov <andrey.petrov@intel.com>
Reviewed-by: Leroy P Leahy <leroy.p.leahy@intel.com>
|
|
The skylake-based Chromebooks use a separate verstage which runs
just after bootblock and prior to romstage. The normal path for
romstage would be to reload the gdt, however in the previously
described scenario has verstage performing that work. Therefore,
provide that path under those conditions. The only difference
from the C_ENVIRONMENT_BOOTBLOCK scenario is that the stack
should not be reloaded since there's no way to know the top
of the stack.
Change-Id: Ic39ab52a856233d3042ac02a15ae4816ddfe07c7
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/14548
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Andrey Petrov <andrey.petrov@intel.com>
Reviewed-by: Leroy P Leahy <leroy.p.leahy@intel.com>
|
|
The path that just clears CAR_GLOBAL variables and jumps
to the stage entry point needs another condition for
separate verstage just after bootblock. However, the
current conditional is a negative conditional so
swap the logic around to make it easier to extend.
Change-Id: Iab6682498054715a6eaa0476390da6355238b9bc
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/14547
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Andrey Petrov <andrey.petrov@intel.com>
Reviewed-by: Leroy P Leahy <leroy.p.leahy@intel.com>
|
|
Utilize the architecture dependent coreboot table size value
from <arch/cbconfig.h>
Change-Id: I80d51a5caf7c455b0b47c380e1d79cf522502a4c
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/14455
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
|
|
Stefan and others have discussed their interest in only
including options in Kconfig that are directly associated
with building a coreboot image. There are variables that
are architecture dependent that are utilized in the
coreboot infrastructure. To meet that goal, introduce
<arch/cbconfig.h> header file which defines variables
for the coreboot infrastructure that are architecture
dependent but utilized in common infrastructure.
Change-Id: Ic4cb9e81bab042797539dce004db0f7ee8526ea6
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/14454
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
|
|
The ECC check bits of all ECC DIMMS were inadvertently initialized
twice in the same routine, significantly delaying startup. Part
of this was related to an obsolete MCA workaround that has been
fixed through multiple commits, therefore the workaround is no
longer needed.
Only initialize the ECC check bits once.
Change-Id: I90ac1147d9b006794d29b866a9cb5b7ead8f01e7
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: https://review.coreboot.org/14503
Tested-by: build bot (Jenkins)
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
C_ENVIRONMENT_BOOTBLOCK on x86 is like romstage and uses cache-as-ram
separately. It does not use any data/bss sections.
Change-Id: I8957f467f01e754fa2d95783466a01daa6c4e51a
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/14533
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Andrey Petrov <andrey.petrov@intel.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Leroy P Leahy <leroy.p.leahy@intel.com>
|
|
Change-Id: Ic0866a5183c64070ef35b21ba00586bc65dfcde8
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/14538
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Change-Id: Id584cbf02c9d3ecb89fcf2a3190f0a73816954a8
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/14526
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Change-Id: If4d57c7898c0de20035533dccd4554f45a71d5d1
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/14525
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Change-Id: Idb948acd1a508379f600fbd2fd40fb26b7571d7c
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: https://review.coreboot.org/14545
Tested-by: build bot (Jenkins)
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
During receiver enable cycle training on Family 15h the entire range
of possible delays is searched, even though the single passing window
is often found nearly immediately. Skip the remainder of the delay
range after the passing window has been located.
Change-Id: If98217fa8e7de77366762d3c7bb01049a1dc080f
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: https://review.coreboot.org/14544
Tested-by: build bot (Jenkins)
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
During DQS receiver enable cycle training on Family 15h platforms the
read data timing registers were inadvertently set to zero on every
lane training attempt.
Ensure that the read data timing registers are correctly set after
each lane is trained in receiver enable cycle training. This allows
more than one RDIMM to function on a given DCT channel.
Change-Id: I87d732f0383e9785a73b57e6f48855f3e872f1f9
Tested-On: ASUS KGPE-D16
Tested-With: 1x Opteron 6262HE
Tested-With: 4x Crucial 36KSF1G72PZ-1G6M1 (slots A2 / A1 / B2 / B1)
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: https://review.coreboot.org/14543
Tested-by: build bot (Jenkins)
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change-Id: I1f5b024606093dc81de3f3d69b7a43e20141b709
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: https://review.coreboot.org/14542
Tested-by: build bot (Jenkins)
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
The existing Family 15h receiver enable training code stored
temporary delay values in the wrong variables, leading to
the requisite averaging of delays across nibbles not being
applied. This in turn made x4 DIMMs less stable than they
should have been.
Store temporary nibble delay values in a dedicated array.
Change-Id: Ic5da898af7d689db4110211f89b886ccdbb5f78f
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: https://review.coreboot.org/14541
Tested-by: build bot (Jenkins)
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Remove the platform_bus_table routine and replace it with a link time
table. This allows the handlers to be spread across multiple modules
without any one module knowing about all of the handlers.
Establish number ranges for both the SOC and mainboard.
TEST=Build and run on Galileo Gen2
Change-Id: I0823d443d3352f31ba7fa20845bbf550b585c86f
Signed-off-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-on: https://review.coreboot.org/14554
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
|
|
Add xor support which enables toggling of a bit:
* REG_SCRIPT_COMMAND_RXW enum value
* REG_*_RXW* macros to support using REG_SCRIPT_COMMAND_RXW
* REG_*_XOR* macros to support using REG_SCRIPT_COMMAND_RXW
* reg_script_rxw routine to perform and/xor operation
* case in reg_script_run_step to call reg_script_rxw
TEST=Build and run on Galileo Gen2
Change-Id: I50a492c7c2643df5dc2d2fa7113e3722c1e480c7
Signed-off-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-on: https://review.coreboot.org/14495
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Change-Id: Ie8e21e62ecd25f3c620a57c24948411c14c1e111
Signed-off-by: Hannah Williams <hannah.williams@intel.com>
Reviewed-on: https://review.coreboot.org/14315
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
The pad for CS2 of the Fast SPI interface needs to be configured for
automatic MMIO translation when a SPI TPM is utilized. Instead of
unconditionally configuring that pad under LPC_TPM provide a explicit
Kconfig for a mainboard to select.
Change-Id: Ia94b90e12d71a4b849359188a853f7e036cc583b
Signed-off-by: Aaron Durbin <adurbin@chormium.org>
Reviewed-on: https://review.coreboot.org/14531
Reviewed-by: Andrey Petrov <andrey.petrov@intel.com>
Tested-by: build bot (Jenkins)
|
|
Fix regression introduced by:
Ib48fe8380446846df17d37b22968f7d4fd6b9b13
Don't run channel_test on S3 resume as it overrides memory
that might be in use.
Fixes MCE events reported by the GNU/Linux kernel that
low memory has been modified.
Reset on failed s3 resume.
Change-Id: Ibadea286619c7906225f86a93aaa0b4caf26cabe
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/14439
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Add new mainboard for MC BDX1 board which is based on Intel Camelback
Mountain. This mainboard is an industry type board and has several
Ethernet interfaces among with two USB3.0 connectors. It uses 24V DC
power supply and has its own form factor which does not match any
standard.
This commit adds the new mainboard and prepares the Kconfig
environment so that this board can be selected and generated.
Although the generated image can boot into Linux and DOS,
not all functions are implemented yet.
Forthcoming commits will add more functionality.
Change-Id: I29011cfd3b0d13bcf163223f657e02f69978e39a
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/14516
Tested-by: build bot (Jenkins)
Reviewed-by: York Yang <york.yang@intel.com>
|
|
DIMM training can sporadically fail due to external influences or various
errata. In these cases, restarting to retry training is a more appropriate
response than halting the system and requiring manual intervention.
Change-Id: Id49f7419f56e0640a84448cc06ecbaf62bed145e
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: https://review.coreboot.org/14529
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Change-Id: Ifdf40986c2407d8c5b0097654b42e056f4498d39
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/14518
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change-Id: If0f835e69862a78433e7c1a34efa4706cc27b214
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/14517
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
To include gfx.c in ramstage, there is a Kconfig option
(FSP_BAYTRAIL_GFX_INIT) which can be activated on demand.
Unfortunately, the "$"-character is missing so that this switch is
never active.
Change-Id: I0c3c562b3caca53ac6510c2c5dc30e7f606f5ad0
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/14532
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Switch all types to uint8_t and the like instead of u8.
Change-Id: Ia12c4ee9e21e2d3166c2f895c819357fa2ed9a94
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/14515
Tested-by: build bot (Jenkins)
Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Use hwilib in vendorcode/siemens/hwilib to get fields from hwinfo
instead of having mainboard specific hwinfo code.
This patch does not change the functional behavior in any way.
Change-Id: Idb226a82a08b1b753f654c5cde106236e72f33c3
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/14506
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Add a library which unifies access to Siemens specific hardware information
data. This library is meant to be used with Siemens platforms and can be
selected in Kconfig. The needed source of information has to be present
in cbfs.
This lib can be used in romstage and ramstage.
Change-Id: I2c6e003b0c123b4cf6a84906c2b133b8c38c8b1a
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/14505
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
|
|
Add chromeos required GNVS feature. The GNVS table stays in both CBMEM
and ACPI DSDT tables.
Change-Id: I4db0eb18d2de62917a94704318a7896c04e4777f
Signed-off-by: Andrey Petrov <andrey.petrov@intel.com>
Reviewed-on: https://review.coreboot.org/14471
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Add GPIO controller in ACPI device description.
GPIO controller driver is probed in kernel and all
the pins in the banks are showing respective values.
Change-Id: I0512cfec872113b15fd204ec3b95efeac87f694a
Signed-off-by: Zhao, Lijian <lijian.zhao@intel.com>
Signed-off-by: Jagadish Krishnamoorthy <jagadish.krishnamoorthy@intel.com>
Reviewed-on: https://review.coreboot.org/14478
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Enable caching of BIOS region with variable MTRR. This is most
useful if enabled early such as in bootblock.
Change-Id: I39f33ca43f06fce26d1d48e706c97f097e3c10f1
Signed-off-by: Andrey Petrov <andrey.petrov@intel.com>
Reviewed-on: https://review.coreboot.org/14480
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
|
|
This adds early LPC setup in bootblock (for Chrome EC) as well as
late (ramstage) IO decode/sirq enable.
Change-Id: Ic270e66dbf07240229d4783f80e2ec02007c36c2
Signed-off-by: Divya Sasidharan <divya.s.sasidharan@intel.com>
Signed-off-by: Freddy Paul <freddy.paul@intel.com>
Signed-off-by: Andrey Petrov <andrey.petrov@intel.com>
Reviewed-on: https://review.coreboot.org/14469
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Use postcar infrastructure to enable caching of area where ramstage
runs.
Change-Id: I3f2f6e82f3b9060c7350ddff754cd3dbcf457671
Signed-off-by: Andrey Petrov <andrey.petrov@intel.com>
Reviewed-on: https://review.coreboot.org/14095
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Move _CRS scope from MCHC device only to whole pci root bus. Otherwise
ACPI will not able to assign resource to devices other than MCHC.
Change-Id: Iaa294c63e03a4fc6644f1be5d69ab3de077e6cc3
Signed-off-by: Zhao, Lijian <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/14477
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Enabled LPC channel between host and EC.
Superio.asl will enable proper probing of onboard keyboard.
Change-Id: I57014fc90b345661853280ae3402f86e56af5fb9
Signed-off-by: Divya Sasidharan <divya.s.sasidharan@intel.com>
Signed-off-by: Freddy Paul <freddy.paul@intel.com>
Reviewed-on: https://review.coreboot.org/14468
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
One of devices connected to FAST SPI bus is TPM. SoC uses dedicated
line for chip select for TPM function. If TPM is used, that line needs
to be configured to a specific native funciton.
Change-Id: Ib5bf4c759adf9656f7b34540d4fc924945d27a97
Signed-off-by: Andrey Petrov <andrey.petrov@intel.com>
Reviewed-on: https://review.coreboot.org/14467
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
coreboot writes RDSP at 0xf0000. Since depthcharge wipes usable
memory regions before starting, kernel can't find RDSP.
Change-Id: I584bd5d24248cf38f46342615cf3b0252a821b2a
Signed-off-by: Andrey Petrov <andrey.petrov@intel.com>
Reviewed-on: https://review.coreboot.org/14466
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Without ACPI PCI IRQ definitions kernel is left only with informaiton
available in PCI config space, which is not sufficient.
Change-Id: I3854781049851b5aa5b2dbf3257ece2fee76c3e2
Signed-off-by: Andrey Petrov <andrey.petrov@intel.com>
Reviewed-on: https://review.coreboot.org/14465
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Memtest86+ was pulling origin/master which will change over time. This
adds a commit-id as a stable version to allow it to be reproducible.
The other secondary payloads, coreinfo and nvramcui, do not need this
because they are part of the coreboot repo and not fetched from an
external source.
Change-Id: I20c516010f76cf03342bd8883d0ee7ac5f8bc7e4
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/14520
Tested-by: build bot (Jenkins)
Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
This series of patches attempts to update all of the external payload
makefiles to be as similar as possible.
- Add .git to the git repo URL to show that it's a git repo.
- Use the common checkout, fetch, and clone ($(project dir)) targets
- Add TAG-y and NAME-y variables - just with origin/master for now.
Stable will be added shortly.
- Make sure all phony targets are in .PHONY
Change-Id: If83c100841d5f91a9fab7ac44ba20ec2271c0594
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/14152
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Test results under 16 days old display with an incorrect background color
due to the leading zero not being preset in the associated HTML color code.
Add the leading zero where needed to generate a valid HTML color code.
Change-Id: I0dfe29ec1afc409a4908073922ac31a4091f0f1f
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: https://review.coreboot.org/14514
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
- Get the absolute pathname for LIBPAYLOAD_PATH
- Update distclean:
--correctly remove .config and .config.old - *.config doesn't match
.config
-- remove obsolete files from cleanup
Change-Id: I6aa51b4ac2b392f786aeb12647be5073e6d02df5
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/14485
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Change-Id: I89dca25d93a4c94cc51f313397e49ba763948450
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/14484
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Change-Id: If845729bc34df646a5628ac2a35acc737fd4701d
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/14483
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
The existing memory test routine was insufficient to detect certain types
of bus instability related to multiple incompatible RDIMMs on one channel.
Add a PRNG second stage test to the memory test routine. This second stage
test reliably detects faults in memory setup for RDIMM configurations that
also fail under the proprietary BIOS.
Change-Id: I44721447ce4c2b728d4a8f328ad1a3eb8f324d3d
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: https://review.coreboot.org/14502
Tested-by: build bot (Jenkins)
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
The wrong DIMM number was used in the initial non-target MRS
setup routines. This had no functional impact other than to
print the wrong DIMM number in the DDR3 verbose debug output.
Change-Id: I480118ed00e1786a06e641a56f0fb19cd87f92eb
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: https://review.coreboot.org/14501
Tested-by: build bot (Jenkins)
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
The existing RDIMM RC control word send routines were a hodgepodge
of various AGESA chunks with different ways of handling the same
task. Unify the control word chip select setup, use precise timing
routines on Family 15h, fix a couple of incorrect masks, and add
additional debugging statements.
It is believed that this patch is cosmetic and does not significantly
alter existing functionality.
Change-Id: Ie4ec7b6a7be7fce09e89f9eec146cc98b15b6160
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: https://review.coreboot.org/14500
Tested-by: build bot (Jenkins)
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Decode each cbfs_payload_segment into native byte order during
segments iteration.
Note :
List ordering has been changed, segments are now always inserted
at the end.
cbfs_serialized.h PAYLOAD_SEGMENT definitions have been changed
to their standard order (big-endian).
Change-Id: Icb3c6a7da2d253685a3bc157bc7f5a51183c9652
Signed-off-by: George Trudeau <george.trudeau@usherbrooke.ca>
Reviewed-on: https://review.coreboot.org/14294
Tested-by: build bot (Jenkins)
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
When more than one DIMM is installed on a DCT, only the first DIMM
delay values are scaled to the new memory clock frequency after a
memory clock change during write leveling.
Store the previous memory clock of each DIMM during write leveling
to ensure that every DIMM has its delay values rescaled.
Change-Id: I56e816d3d3256925598219d92783246f5f4ab567
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: https://review.coreboot.org/14479
Tested-by: build bot (Jenkins)
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
A major issue with the board-status Wiki page is that it shows all
test results equally regardless of age. As a test result ages it
becomes more likely that the board no longer works peroperly under
coreboot due to code churn.
Visually indicate board-test status "at a glance" by smoothly fading
the background color of the test result from green to yellow as the
test result ages. This patch sets the full yellow transition to 255
days after test for programming convenience, however the number of
days required to fully "stale" a test result could be modified
relatively easily.
Change-Id: I5a076a6cc17d53fda8e4681e38074fc1f46c0e12
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: https://review.coreboot.org/14457
Reviewed-by: Vladimir Serbinenko <phcoder@gmail.com>
Tested-by: build bot (Jenkins)
|
|
Add 'nvramcui' target to make it easier to build and test.
Put both nvramcui & coreinfo targets into .PHONY because they
both exist as directories.
Change-Id: I9cf76785e69f3c8e47fe92f1b1648fd0f7a63c3e
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/14481
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
This is in response to issue #28: board-status should reject duplicate
uploads.
Change-Id: Iff99be154b35e8c0f9f05f9470d1c2dcff8510b8
Signed-off-by: Huimin Zhang <thehobn@gmail.com>
Reviewed-on: https://review.coreboot.org/14187
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
On Mac OS X hdestroy seems to overwrite node->name. Hence
duplicate the string before stuffing it into the hash search
table.
Change-Id: Ieac2025f5c960cdb8d509dde7e92ba0dd32644b0
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-on: https://review.coreboot.org/14443
Tested-by: build bot (Jenkins)
Reviewed-by: Idwer Vollering <vidwer@gmail.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
The previous commit removed Kconfig, but not Makefile.inc
Change-Id: If46a0a3e253eea9d286d8ab3b1a6ab67ef678ee4
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-on: https://review.coreboot.org/14419
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Remove offset override improperly added in the "Disable the ROM shadow"
patch
TEST=Build and run on Galileo Gen2
Change-Id: I32fb2da48e3769d59a49619539053f9afdf63b04
Signed-off-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-on: https://review.coreboot.org/14450
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Initialize the d_variant variable.
Found-by: CID 1353356 Uninitialized variable
TEST=Build and run on Galileo Gen2
Change-Id: I26fba4e77f91d53b6ff9028669aa0186d3174639
Signed-off-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-on: https://review.coreboot.org/14338
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
After substantial testing it has been determined that it is neither
required nor safe to disable the DRAM MCA during initial startup.
This (mostly) reverts commit c094d9961144871c472698c41ce634e58abb6a32.
The minor debugging enhancements from that commit were left in place.
Tested-On: ASUS KGPE-D16
Config-CPU: 1x Opteron 6262HE
Config-RAM: 4x Crucial 36KSF1G72PZ-1G6M1
Config-RAM: 1x Kingston 9965516-483.A00LF
Change-Id: I58fcc296b8c45ecaedf540951c365e4ce52baaf5
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: https://review.coreboot.org/14446
Tested-by: build bot (Jenkins)
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change-Id: I5056cf885b7063a97c095bfaaf01dd8da777a425
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: https://review.coreboot.org/14447
Tested-by: build bot (Jenkins)
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Certain RDIMMs have inherently large write levelling delays,
in some cases exceeding 1.5 MEMCLK. When these DIMMs are
utilized, the phase recovery system requires special handling
due to the resultant offset exceeding the phase recovery reporting
capabilities.
Fix an old error where delays > 1.5 MEMCLK were not being programmed
(gross delay high bit was not in set range), and restore special
delay handling for delays greater than 1.5 MEMCLK.
Also enhance debugging for x4 DIMMs around the affected code.
Tested-On: ASUS KGPE-D16
Config-CPU: 1x Opteron 6262HE
Config-RAM: 4x Crucial 36KSF1G72PZ-1G6M1
Change-Id: I0fb5454c4d5a9f308cc735597607f095fe9188db
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: https://review.coreboot.org/14441
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
The BKDG requires phy fences to be re-trained after a memory clock change.
Memory training on the ASUS KGPE-D16 and KCMA-D8 somehow "mostly" worked
-- without actually following this requirement -- !
Fix the single typo that caused several weeks of delay in putting
servers with Kingston RAM (and others) into production...
Tested-On: ASUS KGPE-D16
Config-CPU: 1x Opteron 6262HE
Config-RAM: 4x Crucial 36KSF1G72PZ-1G6M1
Change-Id: I197e6728d2b0ac8c1535740599459d080b17af33
Signed-off-by: Timothy Pearson <tpearson@raptorengineeringinc.com>
Reviewed-on: https://review.coreboot.org/14445
Tested-by: build bot (Jenkins)
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
In program_segment_loaded, flush L1D to L2 only if the address of the
loaded segment lies in the CAR region. Add an assert to ensure that
the loaded segment does not cross CAR boundaries.
Change-Id: Ie43e99299ed82f01518c8a1c1fd2bc64747d0c7b
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/14449
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
|
|
Fixes two issues:
1. In (the unlikely) case that dev->chip_info is NULL, the output was
depending on an unknown value near the start of the address space.
2. Output for the secondary interface actually printed the primary
interface's configuration.
Change-Id: Id0f499a85e6e2410b4efd63baf7fffb2fcaa3103
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Reviewed-on: https://review.coreboot.org/14361
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Fix warnings:
Unescaped left brace in regex is deprecated, passed through in regex;
marked by <-- HERE in m/\#\s*define.*do\s{ <-- HERE / at util/lint/checkpatch.pl line 3261.
marked by <-- HERE in m/\(.*\){ <-- HERE / at util/lint/checkpatch.pl line 3750.
marked by <-- HERE in m/do{ <-- HERE / at util/lint/checkpatch.pl line 3751.
marked by <-- HERE in m/^\({ <-- HERE / at util/lint/checkpatch.pl line 4194.
Change-Id: If0c1f07a16df9e6cd1c1393a31af8b8ea6a66b01
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Reviewed-on: https://review.coreboot.org/14310
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
The coding guidelines say that all objects should have fully
qualified types (unsigned int instead of unsigned).
This script finds violations of that rule.
Steps for the filter:
1) Find all lines in the coreboot tree that have the word 'unsigned'
followed by a space.
2) Exclude directories that aren't in the include list or
are specifically excluded.
3) Exclude files that aren't specifically included.
4) Filter out legimitate uses 'unsigned int' or 'unsigned long' for
example.
5) Filter out lines that begin with '/*' or '*'
Change-Id: I46213c6a168e6aafa29a50af814bf7e0fcd32eb6
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/14269
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Move time functions and prototypes from libpayload.h to time.h.
In a similar manner to other c libary headers, this change makes
porting existing applications to libpayload easier.
Change-Id: I71e27c6dddde6e77e0e9b4d7be7cd5298e03a648
Signed-off-by: Stef van Os <stef.van.os@prodrive-technologies.com>
Reviewed-on: https://review.coreboot.org/14437
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Change-Id: Idda4b7179e3e7b3f5b70be810b428b0651c1cd67
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/14427
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
When building libpayload, make the build directory and .config outside
libpayload source directory so it'll not pollute the libpayload source
and cause conflicts with other builds.
Change-Id: Idcfbc7dbe4d52a3559229d8450c3efaafd33b93b
Signed-off-by: Iru Cai <mytbk920423@gmail.com>
Reviewed-on: https://review.coreboot.org/14389
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
In order to de-duplicate common patterns implement one write_tables()
function. The new write_tables() replaces all the architecture-specific
ones that were largely copied. The callbacks are put in place to
handle any per-architecture requirements.
Change-Id: Id3d7abdce5b30f5557ccfe1dacff3c58c59f5e2b
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/14436
Tested-by: build bot (Jenkins)
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Add a architecture specific function, arch_write_tables(), that
allows an architecture to add its required tables for booting.
This callback helps write_tables() to be de-duplicated.
Change-Id: I805c2f166b1e75942ad28b6e7e1982d64d2d5498
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/14435
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
A architecture-specific function, named bootmem_arch_add_ranges(),
is added so that each architecture can add entries into the bootmem
memory map. This allows for a common write_tables() implementation
to avoid code duplication.
Change-Id: I834c82eae212869cad8bb02c7abcd9254d120735
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/14434
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
The x86 architecture needs to add a forwarding table to
the real coreboot table. Provide a helper function to do
this for aligning the architectures on a common
write_tables() implementation.
Change-Id: I9a2875507e6260679874a654ddf97b879222d44e
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/14433
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
In addition to being consistent with all other architectures,
all chipsets support cbmem so the low coreboot table path is
stale and never taken. Also it's important to note the memory
written in to that low area of memory wasn't automatically
reserved unless that path was taken. To that end remove
low coreboot table support for x86.
Change-Id: Ib96338cf3024e3aa34931c53a7318f40185be34c
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/14432
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
There were quite a number of #if/#endif guards in the
write_tables() code. Clean up that function by splitting
up the subcomponents into their own individual functions.
The same ordering and logic is kept maintained.
The changes also benefit the goal of using a common core
write_tables() logic so that other architectures don't
duplicate large swaths of code.
Change-Id: I93f6775d698500f25f72793cbe3fd4eb9d01a20c
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/14431
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Each arch was calling cbmem_list() in their own write_tables()
function. Consolidate that call and place it in common code
in write_coreboot_table().
Change-Id: If0d4c84e0f8634e5cef6996b2be4a86cc83c95a9
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/14430
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Instead of hard coding a #define in each architecture's
tables.c for the coreboot table size in cbmem use a Kconfig
varible. This aids in aligning on a common write_tables()
implementation instead of duplicating the code for each
architecture.
Change-Id: I09c0f56133606ea62e9a9c4c6b9828bc24dcc668
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/14429
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Apparently the memo was missed about the write_tables()
signature. Fix the confusion.
Change-Id: I8ef367345dd54584c57e9d5cd8cc3d81ce109fef
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/14421
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Apparently the memo was missed about the write_tables()
signature. Fix the confusion.
Change-Id: I63924be47d3507d2d7ed006a553414f4ac60d2f9
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/14420
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Set the default memory type in MTRRCap register to 0. This ensures
that even if the MTRR Enable bit is set in MTRRCap register, the
default memory type is still uncacheable.
Change-Id: I63e7993f8b65dabbab60e7c1bb8d6d89ef4da9ee
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/14428
Tested-by: build bot (Jenkins)
Reviewed-by: Andrey Petrov <andrey.petrov@intel.com>
|
|
Fix is required to compile AGESA ramstage without raminit.
Change-Id: I783883fa7a12e8a647aa432535bb990a47257e9b
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/14416
Tested-by: build bot (Jenkins)
Reviewed-by: Kerry Sheh <shekairui@gmail.com>
|
|
Change-Id: Icc1361fdd3a8369c4b442ce5b8807c549519c93a
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-on: https://review.coreboot.org/14387
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
With binutils 2.26 our memlayout ASSERT for mirrored SRAM regions
gets confused due to the lack of parentheses grouping the expressions.
This fixes the following issue:
LINK cbfs/fallback/bootblock.debug
mipsel-elf-ld.bfd: bootblock and gram_bootblock do not match!
mipsel-elf-ld.bfd: romstage and kseg0_romstage do not match!
Change-Id: Ib406e229b8a552d9ffc4538b55ee0269bfed62a8
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-on: https://review.coreboot.org/14440
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Change-Id: Id9487212411e5c237d26eb4e5663135f7d0720d1
Signed-off-by: Noah Glovsky <noah.glovsky@watershedschool.org>
Reviewed-on: https://review.coreboot.org/14425
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change-Id: Ida8e81c88b2016d90cc8305edfb199143f859ec2
Signed-off-by: Noah Glovsky <noah.glovsky@watershedschool.org>
Reviewed-on: https://review.coreboot.org/14422
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
File type for SPD in this soc is defined as CBFS_TYPE_RAW in Makefile,
but CBFS_TYPE_SPD in code.
Causes DDR SPD not to be loaded on memory down.
Tested on Prodrive Technologies Broadwell-D 1548 module:
http://prodrive-technologies.com/amc-ix5-intel-broadwell-de-platform/
Change-Id: I44525b4742b3f93d33f0c5bd9ed642c6fb06f23f
Signed-off-by: Stef van Os <stef.van.os@prodrive-technologies.com>
Reviewed-on: https://review.coreboot.org/14415
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: York Yang <york.yang@intel.com>
|
|
Change-Id: Ife26f5cf6a06a1a5bf965bbeed7a740a990e8f7f
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Reviewed-on: https://review.coreboot.org/14399
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Add amenia board files
Change-Id: I6731a348b4c0550d3b9381adb5fb83719f90a5da
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Reviewed-on: https://review.coreboot.org/14352
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Provide trigger option to configure APIC, sci, smi, nmi interrupts.
Change-Id: I1b553fb4ed1b43aba62346f5b758f8d082606510
Signed-off-by: Jagadish Krishnamoorthy <jagadish.krishnamoorthy@intel.com>
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Reviewed-on: https://review.coreboot.org/14353
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Change-Id: Ide3202fca75c77ccebf17d61d93945ba7834a13b
Signed-off-by: Andrey Petrov <andrey.petrov@intel.com>
Reviewed-on: https://review.coreboot.org/14398
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Change-Id: Ie38a358ebd2d040ce32b3eeaeb664c568d4dc51e
Signed-off-by: Iru Cai <mytbk920423@gmail.com>
Reviewed-on: https://review.coreboot.org/14378
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
|
|
* use crossgcc to build nvramcui
* build libpayload dependency
Change-Id: Ife3054aeb03b4da0568ad47f96c633460d6c07ae
Signed-off-by: Iru Cai <mytbk920423@gmail.com>
Reviewed-on: https://review.coreboot.org/14377
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Compiling libagesa with -O2 would throws error on these.
Change-Id: I04afa42f0ac76677f859ca72f9df2e128762ad3c
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/14413
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
We have not really hit this error, due the test on AGESA_UNSUPPORTED
above.
Change-Id: I6e7d136a1bb46138cc347225bc4c82cfeaff385d
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/14394
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
We never define B1_IMAGE or B2_IMAGE. These are about building
CIMx as separate binary modules, while coreboot builds these into
same romstage or ramstage module.
Change-Id: I9cfa3f0bff8332aff4b661d56d0e7b340a992992
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/14393
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Kerry Sheh <shekairui@gmail.com>
|
|
The ME hangs, the lspci shows no memory and the linux kernel
tries to request irq 0 twice. After suspend-resume the linux
kernel warns about double used irq.
genirq: Flags mismatch irq 0. 00000080 (mei_me) vs. 00015a00 (timer)
mei_me 0000:00:16.0: request_threaded_irq failed: irq = 0.
dpm_run_callback(): pci_pm_resume+0x0/0xa0 returns -16
PM: Device 0000:00:16.0 failed to resume async: error -16
Change-Id: I56ef66388e58dddcfb858294ba274621c55fbef6
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Reviewed-on: https://review.coreboot.org/14309
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
Because the builders have the coreboot cross-compilers in their path,
the XGCCPATH variable needs to be set after building the new toolchain
before it will be used.
- Add $DEST/bin to $PATH if $DEST is set, add the default location
for toolchain builds otherwise. Because the jenkins build image puts
the tools in the path, we ca
- Add KEEP_SOURCES option to help speed up compilation (Slightly).
- Log .xcompile for verification that the right toolchain was used.
- Verify that test-toolchain passes.
Change-Id: I7c270dab94be7e8f801d527169767018a24986e4
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/14231
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Change-Id: I3c34f6e69b3760a10e67bdc41c8ef0e629beb881
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/14129
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Reorder drivers to fit src/drivers/[X]/[Y]/ scheme to make
them pluggable.
Change-Id: I3cf32ec58ba40db11fae3dda6dcb2375002e7cb4
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-on: https://review.coreboot.org/14052
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Reorder drivers to fit src/drivers/[X]/[Y]/ scheme to make
them pluggable.
Change-Id: Ide0d48405d85ea2e889916f778e1556287651707
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-on: https://review.coreboot.org/14057
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
