| Age | Commit message (Collapse) | Author |
|---|
|
This MSR will be used in the follow-up changes.
Change-Id: Ia6f74861502d4a9f872b2bbbab2e5f1925a14c4d
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49044
Reviewed-by: Lance Zhao
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Remove these comments, because it does not contain useful information
that helps to understand the circuit, which we do not have.
Tested with BUILD_TIMELESS=1, Razer Blade Stealth, remains identical.
Change-Id: I8a8450493ceebe97ac03b4134adc46b01328a1b6
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45370
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
modify raydium touch screen power on timing to meet requirement
BUG=b:174280232
TEST=build firmware and measured the timing
Signed-off-by: Ren Kuo <ren.kuo@quanta.corp-partner.google.com>
Change-Id: I3ecc9d8e21f8c76e9e96cf050dcde83c3c4f4ea7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48971
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Configure the I2C bus high and low times for port0,2 and 4 I2C buses.
BUG=b:176519792
TEST=Measured the I2C bus frequency lower than 400 KHz.
Change-Id: Ieed038c93f0972c06cb3fa311742dd22ac2e875d
Signed-off-by: Tim Chen <tim-chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49014
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Follow Goodix datasheet (GT7375 Programming Guide_Rev.0.1.pdf and
GT7375P Programming Guide_Rev.0.6.pdf) to tune touchscreen power sequence.
Increase reset_delay_ms from 120ms to 180ms.
BUG=b:176511605
BRANCH=dedede
TEST=Build and boot Madoo to OS
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Change-Id: Iae35e4da31a3c3afd24c7daf81a5a3e762acd3b4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49011
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
|
|
Configure the I2C bus high and low time for all enabled I2C buses.
BUG=b:168783630
TEST=Measured the I2C bus frequency reduce to 387 KHz.
Signed-off-by: Stanley Wu <stanley1.wu@lcfc.corp-partner.google.com>
Change-Id: I37403dd3ac3c9320398207d2111e1ddb73d6a130
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48878
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marco Chen <marcochen@google.com>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Config I2C high / low time in device tree to ensure I2C
CLK runs accurately at I2C_SPEED_FAST (400 kHz).
These tuning value is applied from touchpad as a base line,
and EE measured touchscreen/audio runs at 399/396.7kHz after tuning.
BUG=b:173709409
BRANCH=dedede
TEST=Build and check after tuning I2C clock is under 400kHz
Change-Id: I970d69e6361d7cf6fcfc4e5b0b3c5fbfa885367c
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49020
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
BUG=b:173709409
BRANCH=dedede
TEST=EE measured result is 390.8kHZ
Change-Id: I7a6475fd29d4c9f8efa78a42a112b5565511b939
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48867
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
According Goodix GT7375P Programming Guide_Rev.0.6, increase the stop
delay time from 100 ms to 160 ms.
The power sequence is not met with the latest guide_rev.0.6.
BUG=b:176270381
BRANCH=zork
TEST=Confirm the measured waveform complies with Goodix touchscreen spec.
Signed-off-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
Change-Id: I687ffa2eb13a9ddecb3045c5e1540b94417329ec
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48907
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Rob Barnes <robbarnes@google.com>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=b:176307061
TEST=emerge-asurada coreboot; emerge-kukui coreboot emerge-oak coreboot
boot to shell on Asurada
Signed-off-by: Yidi Lin <yidi.lin@mediatek.com>
Change-Id: Id31fa04edc2920c1767d9f08ab7af0ab4a15bc24
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49137
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
All Broadwell boards use 8 for MAX_CPUS, so this option can be factored
out into SoC Kconfig.
Change-Id: I311b95ea75a7c6b76b32c7197a0cec86db644234
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49122
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Configure MAX_CPUS in SoC Kconfig with 8 as default value and remove it
from every mainboard where 8 is used.
Change-Id: I825625bf842e8cd22dada9a508a7176e5cc2ea57
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49105
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Haswell and Broadwell have at most 8 threads.
Change-Id: Idcccf22addb6e15d7c55b9816141af47d6186cca
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46952
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
On Voema port 0 (MB PORT) does not have a retimer so the port needs
to be configured for the SOC to handle Aux orientation flipping.
BUG=b:176462544
TEST=tested on voema
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: I3d31a5b848f56126f8ffe2babb29085471e8224f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48976
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
|
|
This table was wrong. It's also produced by the SoC code now.
BUG=b:170595019
TEST=None
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Ifcc406591abf88ebdb5ed972614c3a6901721bac
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48667
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nikolai Vyssotski <nikolai.vyssotski@amd.corp-partner.google.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
This table was wrong. It's also produced by the SoC code now.
BUG=b:170595019
TEST=Verify PCI IRQ: log messages
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I008b6896064672f9d45a8e12f6cfc62c0cc41536
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48666
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nikolai Vyssotski <nikolai.vyssotski@amd.corp-partner.google.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
The PCI interrupt line registers are used as a last resort if routing
can't be fetched from either ACPI or the MPTable. This change correctly
sets the registers. It overrides the pirq_data set by the mainboards
since the routing is fixed in AGESA.
BUG=b:170595019
TEST=Boot ezkinil with `pci=nomsi,noacpi amd_iommu=off noapic`
Verified all PCI peripherals are still functional.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: If5d4d8f613c8d0fa9b43cefa804824681c3410d6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48665
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nikolai Vyssotski <nikolai.vyssotski@amd.corp-partner.google.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
The original routing table did not handle all 8 INTx interrupts.
Additionally it also didn't take the swizzling into account.
Now that we know how AGESA programs the routing table we can correctly
generate it.
We still route the PCI interrupts through the FCH IOAPIC. A follow up
will have the GNB IOAPIC handle the PCI interrupts.
There is still work to be done to fix the legacy PCI_IRQ register for
each PCI device. We can then remove the mainboard_pirq_data from each
mainboard.
BUG=b:170595019
TEST=Used ezkinil
Boot kernel with `pci=nomsi amd_iommu=off noapic` and
`pci=nomsi amd_iommu=off` then verified system
was usable and verified /proc/interrupts looked correct.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I2b2cce9913081d5cd456043ba619a79c1dfd4a8e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48632
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nikolai Vyssotski <nikolai.vyssotski@amd.corp-partner.google.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
The set_resources field in the root_complex_operations struct shouldn't
be NULL, but a pointer to noop_set_resources instead. This fixes the
error "PCI: 00:00.0 missing set_resources".
Change-Id: I2d9f3850b3051c92cd9c0f52f8570f4fd6133070
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49120
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
When configuring a GPIO pin as output the value should be written before
it gets configures as an output to avoid a possible glitch on the output
when the GPIO pin was an input before and the output value was different
from the one that got written afterwards.
Change-Id: I2bb5e629ef0ed2daadc903ecc1852200fe3a5cb9
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49119
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
The functions to configure a GPIO as input with pull-up/down need to
clear the output enable bit, so that the direction will be input. If the
pin was configured as output before, the pin direction was still output
after this call which is at least unexpected.
Change-Id: Id1fa1669195080b34fd62324616825415728b0b4
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49118
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
If the pin was configured as pull-up/down before this wouldn't get
cleared when calling gpio_input before.
Change-Id: I17d5eccb7492138e64abaecbd7cb853adb8c4d2d
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49117
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Since there's only one set of values, the if-clause is unnecessary.
Change-Id: I2fb4582377fe2f204d2cee0dc513a4d5d24feabe
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49090
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
They aren't specific to AC power operation anymore. Also adapt autoport.
Change-Id: Ib04d0a08674b7d2773d440d39bd6dfbd4359e0fb
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49089
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
All mainboards use the same values for AC and battery, even desktop
boards without a battery. Use the AC values everywhere and drop the
battery values. Subsequent commits will rename the AC power options
accordingly, and will also clean up the corresponding acpigen code.
This is intentional so as to ease reviewing the devicetree changes.
Also update util/autoport accordingly.
Change-Id: I581dc9b733d1f3006a4dc81d8a2fec255d2a0a0f
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49088
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
It is not used anywhere. Drop it.
Change-Id: I92a72a46db237cf855491a664cdfadca34306f6c
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49087
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: Iacb1fb0a1309c3c23e670fee540514b6f546314a
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49066
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
To allow adjusting the phase shift of the various I/O signals, the
memory controller contains several PIs (Phase Interpolators). These
devices subdivide a QCLK (quarter of a clock cycle) in 64 `ticks`,
and the desired phase shift is specified in a register. For shifts
larger than one QCLK, there are `logic delay` registers, which allow
shifting a whole number of QCLKs in addition to the PI phase shift.
The number of PI ticks in a QCLK is often used in raminit calculations.
Define the `QCLK_PI` macro and use it in place of magic numbers. In
addition, add macros for other commonly-used values that use `QCLK_PI`
to avoid unnecessarily repeating `2 * QCLK_PI`, such as `CCC_MAX_PI`.
Tested with BUILD_TIMELESS=1, Asus P8Z77-V LX2 does not change.
Change-Id: Id6ba32eb1278ef71cecb7e63bd8a95d17430ae54
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49065
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
https://qa.coreboot.org/job/untested-coreboot-files reports a bunch of
untouched Makefiles, so we never even attempt to build those tools.
Change-Id: I70ca658d9642b84fa8388c72ecb83327a6a74291
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47446
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
|
|
This patch updates CPU microcode patch base address/size to FSP-S
UPD to have second microcode patch loaded successfully to enable
Mcheck flow.
This is new feature requirement for ADL as per new Mcheck initialization
flow.
BUG=b:176551651
TEST=Able to reach beyond PC6 without any MCE.
Change-Id: I936816e3173dbcdf82b2b16b465f6b4ed5d90335
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48847
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The EC generates EC_MKBP_EVENT_DP_ALT_MODE_ENTERED when USB-C
connections enter DP alt mode, which should wake the system from S3.
Configure S3 wake events to include MKBP so this actually wakes
the system.
BUG=b:174121852
BRANCH=zork
TEST=Generating DP event on MKBP via EC console wakes morphius
Change-Id: I8100c6253e8e5cae91586c4f2f45d66c15fecc6d
Signed-off-by: Peter Marheine <pmarheine@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48844
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Reviewed-by: Sam McNally <sammc@google.com>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Drop unused definition and remove outdated comments.
Change-Id: I16033b558fe4c01a9394382dc0c9d0bdc66193d9
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46993
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
|
|
INT[E-H] are required because the GNB IO-APIC maps the 32 interrupts
onto the 8 INT[A-H] that feed into the FCH PIC/IO-APIC.
BUG=b:170595019
TEST=Verify ezkinil still boots
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I9c6689e212b136f6f3c64152803ed161b2284275
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48664
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nikolai Vyssotski <nikolai.vyssotski@amd.corp-partner.google.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Enable IPU for voema for MIPI camera.
BUG=b:169551066
TEST=IPU is enabled and shows in lspci.
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: I34736bffd4dc61a840003afe5afd6a9c8dc32e62
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49002
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Rework Kconfig file so that each variant has its own config option with
their specific selects / configuration and move common selects to a
seperate config option, which is used as base for each variant.
Built clevo/l140cu with BUILD_TIMELESS=1, coreboot.rom remains the same.
Change-Id: I1f5b6f535597149f28dd8c8322acc2e988f11505
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49025
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
Rework Kconfig file so that each variant has its own config option with
their specific selects / configuration and move common selects to a
seperate config option, which is used as base for each variant.
Built clevo/n130wu with BUILD_TIMELESS=1, coreboot.rom remains the same.
Change-Id: I1f07b5851ece6d0943faa9c90fc518805880a27d
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49060
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Daniel Maslowski <info@orangecms.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Rework Kconfig file so that each variant has its own config option with
their specific selects / configuration and move common selects to a
seperate config option, which is used as base for each variant.
Built chili/base with BUILD_TIMELESS=1, coreboot.rom remains the same.
Change-Id: I5e2a09db80232457b2f78ad9b100c468d281f753
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49063
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Rework Kconfig file so that each variant has its own config option with
their specific selects / configuration and move common selects to a
seperate config option, which is used as base for each variant.
Built kontron/boxer26 with BUILD_TIMELESS=1, coreboot.rom remains the
same.
Change-Id: I08bd68aa2f98f93b8c5daf1ab2f3c1bbce521c53
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49061
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Built with BUILD_TIMELESS=1, coreboot.rom remains the same.
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Change-Id: Ibc6833d9256800d0e50651cac18a4e81ddbe6895
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48144
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Move include directories from carriers and variants to mainboard level
being able to reuse them later. Also, rename guards so that they fit
their usage.
Built with BUILD_TIMELESS=1, coreboot.rom remains the same.
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Change-Id: I55af05cb84b97d567ce1fc3b6151c34d1eda183f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48142
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Fix off-by-1 count of NID entries.
Change-Id: I65f70d084022c99233144b460542a793eae2acf3
Signed-off-by: Matt DeVillier <matt.devillier@puri.sm>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49106
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
All platforms moved to initialise GNVS at the time
of SMM module loading.
Change-Id: I31b5652a946b0d9bd1909ff8bde53b43e06e2cd9
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48699
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I9d7417462830443f9c96273d2cc326cbcc3b17dd
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48698
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add ACPI backlight support for boards selecting BOARD_GOOGLE_BASEBOARD_HATCH.
PUFF-based variants do not have an internal panel, so do not need this.
Test: build/boot Windows 10 20H2 on google/akemi, verify
display backlight controls functional.
Change-Id: I5ce4c6e1c78299e89760a1356da452d56ba0aee6
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49058
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enables backlight control under Windows 10.
Test: build/boot Windows 10 20H2 on google/reef, verify
display backlight controls functional.
Change-Id: I4ce613badbdcfb9c843f52408df26c6cbb4b82a2
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49057
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
Converts bit field macros to target PAD_CFG_*() macros. To do this,
the following command was used:
./intelp2m -n -t 1 -file ../../src/mainboard/razer/blade_stealth_kbl/
gpio.h
This is part of the patch set
"mb/razer/blade_stealth_kbl/gpio: Rewrite pad config using intelp2m":
CB:43857 - 1/3 Decode raw register values
CB:43858 - 2/3 Exclude fields for PAD_CFG
CB:43411 - 3/3 Convert field macros to PAD_CFG
Tested with BUILD_TIMELESS=1, Razer Blade Stealth, remains identical.
Change-Id: Ie9da1246b784578c1e29acc5c61a918841de7468
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43411
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
Change-Id: I65fdee350273c58e027a002dba1f97a56115e195
Signed-off-by: Lance Zhao <lance.zhao@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48970
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Bora Guvendik <bora.guvendik@intel.com>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add functions to read the system and mainboard serial numbers
from VPD tables stored in flash.
Remove board-specific implementations for google/drallion and
google/sarien and select the new Kconfig instead.
Test: build/boot google/akemi with RO_VPD region persisted from
stock Google firmware, verify system/mainboard serial numbers
present via dmidecode.
Change-Id: I14ae07cd8b764e1e22d58577c7cc697ca1496bd5
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49050
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Currently, use of the VPD driver to read VPD tables from flash
requires the use of a custom FMAP with one or more VPD regions.
Extend this funtionality to boards using the default FMAP by
creating a dedicated VPD region when the driver is selected.
Test: build qemu target with CONFIG_VPD selected, verify entry
added to build/fmap.fmd.
Change-Id: Ie9e3c7cf11a6337a43223a6037632a4d9c84d988
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49049
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Change-Id: I479e1eb5819c42621e8b17367b964124d5433378
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48746
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
The LPEA device memory resources, required by Windows drivers,
were not being set. Allocate required resources using
soc/intel/braswell/acpi/southcluster.asl as a reference.
This patch alone is not sufficient for working audio under Windows
on Baytrail ChromeOS devices, but it is a necessary component.
Test: boot Windows 10 on google/swanky, observe LPEA device working properly.
Change-Id: I7994d9b2c6e134c01b05cd7c61d309b6ba6e88e5
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48745
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The (now removed) ID_SECTION_OFFSET=0x80 was actually the
secondary address flashrom and FILO are looking for. The
primary was 0x10, just below .reset.
If .id does not collide with .fit_pointer, use the higher
of the two locations.
Change-Id: I0d3a58c82efd3bbf94f4bc80ec5bbc97d5b1c109
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48499
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
intel_txt_memory_has_secret() checks for ESTS.TXT_ESTS_WAKE_ERROR_STS
|| E2STS.TXT_E2STS_SECRET_STS and it looks like with CBNT the E2STS
bit can be set without the ESTS bit.
Change-Id: Iff4436501b84f5c209add845b3cd3a62782d17e6
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47934
Reviewed-by: Jonathan Zhang <jonzhang@fb.com>
Reviewed-by: Christian Walter <christian.walter@9elements.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
New util directories have been added with no description.md file.
The description file for supermicro was added at a secondary level,
which doesn't help a user find the util since no path was added. Move
it up to the top level.
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: I40b4c25dd7706513e96c6b8078a34160f8bb901e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48961
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tom Hiller <thrilleratplay@gmail.com>
|
|
There's no need to use `memset` here.
Change-Id: I0478bc3ff25b75bf0b554aa83ead6a63fcbd975c
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49064
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Remove index0 DRAM assignment since it doesn't use in any build.
Add Hynix DDR4 DRAM H5ANAG6NCJR-XNC, index was generated by gen_part_id
BUG=b:175911098
BRANCH=zork
TEST=emerge-zork coreboot
Change-Id: I853a316c266afafeecff67b263005a77be316e2b
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48723
Reviewed-by: Rob Barnes <robbarnes@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
PUFF-based Chromeboxes need more than the 2s default in order to init
an external display and show the boot splash/menu prompt.
Test: build/boot WYVERN variant, ensure boot splash/menu prompt visible
regardless of display init type used.
Change-Id: Ie6d2151d28058501498a4c501bb221919b4e1b39
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48979
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
These Chromeboxes need more than the 2s default in order to init
an external display and show the boot splash/menu prompt.
Test: build/boot one of each variant, ensure boot splash/menu
prompt visible regardless of display init type used.
Change-Id: Ib90136b7e564451aff638af4d42abd97e42b3c19
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48978
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
As per HID over I2C Protocol Specification[1] Version 1.00 Section 7.4,
the interrupt line used by the device is required to be level triggered.
Hence, this change updates the configuration of the HID over I2C devices
to be level triggered.
References:
[1] http://download.microsoft.com/download/7/d/d/7dd44bb7-2a7a-4505-ac1c-7227d3d96d5b/hid-over-i2c-protocol-spec-v1-0.docx
[2] https://review.coreboot.org/c/coreboot/+/47417/2/src/mainboard/google/hatch/variants/baseboard/gpio.c#b182
Tested successfully on Clevo L141CU.
Change-Id: Ia232c0a11546aa6d17614f4cab07c255e58f2fed
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47984
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Enables backlight control under Windows 10.
Test: build/boot Windows 10 20H2 on google/ampton, verify
display backlight controls functional.
Change-Id: I779f7f3f5a111018fc7b5c50c5750a9eb815d670
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40594
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
Add struct i915_gpu_controller_info for boards to supply info needed
to generate ACPI backlight control SSDT.
Hook into soc/common framework by implementing intel_igd_get_controller_info().
Add Kconfig entries to set the correct register offsets for backlight
frequency and duty cycle.
Change-Id: Ia62a88b58e7efd90f550000fc5b2cef0cb5fade7
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40593
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: Id58bb2ce5fdaeaf158d02d8c812ab2c331db352d
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48751
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add the panel settings dumped from vendor firmware and hook up
drivers/intel/gma, which will be required for brightness control.
Keyboard brightness control still requires ACPI code. This will be done
in a separate change later.
Test: Panel gets enabled when the payload starts on Clevo L141CU.
Change-Id: I7977a2271da72c142b025b4631318d1a39adfb13
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48750
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Add a new macro `GMA_DEFAULT_PANEL(ssc)` as shortcut for specifying one
internal panel at port A (0) in the devicetree.
Change-Id: I5308b53667657d0b255ae5bc543f1a00431f5818
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49054
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Change-Id: Ia19018685749efdd543cb09c06df117690ab9d66
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48803
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: Ib78e746875e330e47540a6199343be62aa7e92a6
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48830
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I964f4340caa20124a15e52c055d2f27ba5113687
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48783
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change allows to remove some <chromeos/gnvs.h> exposure from
coreboot proper.
Change-Id: I7817914cc7b248331bb8fa79baa642ed548bbc11
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48782
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Move CPUID definitions out of msr.h into new cpuid.h header.
BUG=b:155307433
BRANCH=Zork
Change-Id: I2ed5e0a5a6dbdb38fce8bf3e769f680330718653
Signed-off-by: Jason Glenesk <jason.glenesk@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48533
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
Add cb support to publish CRAT ACPI object in native coreboot.
BUG=b:155307433
BRANCH=Zork
Change-Id: I5fb7c15b11414f6d807645921c0ff1ab927e6e0f
Signed-off-by: Jason Glenesk <jason.glenesk@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48532
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
Instead of checking for an already fully build `libpayload.a`, we check
for the `libpayload.config` which is the actual prerequisite to start
using `lpgcc`. This will allow compilation of payload sources before or
in parallel with the build of `libpayload.a`.
Change-Id: Ic0143fefe33560af8b013ae48bbbe231b3ad46f3
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48938
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Introduce a `$_OBJ` variable, that points to the build directory for
in-tree usage of `lpgcc`. If unset, the default `../build` relative
to the location of `lpgcc` is used.
Change-Id: I35112d7533d69aa51252dd2bceec010a62522403
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47629
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This should make it easier to find the correct config for in-tree
builds.
Change-Id: I08d396ae3cedc65f63c4b8865701ea123c7d56cb
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47628
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Keep libpayload's xcompile in its build dir. While we are at it,
align things with the top-level version.
Having `.xcompile` in a central place led to race conditions when
multiple payloads try to build their own libpayloads in parallel.
Change-Id: I504e1862db79b368289867f7568c9169f27a1549
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47651
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Add code for panel and backlight configuration.
Tested successfully with libgfxinit on Clevo L141CU.
Change-Id: If619b28478b4b0d18f28f318c16336e0de76e129
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48749
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
There are multiple different devicetree setting formats for graphics
panel settings present in coreboot. Replace the ones for the platforms
that already have (mostly) unified gma/graphics setup code by a unified
struct in the gma driver. Hook it up in HSW, BDW, SKL, and APL and adapt
the devicetrees accordingly.
Always ensure that values don't overflow by applying appropriate masks.
The remaining platforms implementing panel settings (GM45, i945, ILK and
SNB) can be migrated later after unifying their gma/graphics setup code.
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: I445defe01d5fbf9a69cf05cf1b5bd6c7c2c1725e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48885
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
For easier review of the switch to a new register struct in the
follow-up change, the panel delay times get converted from destination
register raw format to milliseconds representation in this change.
Formula for conversion of power cycle delay:
gpu_panel_power_cycle_delay_ms =
(gpu_panel_power_cycle_delay - 1) * 100
Formula for all others:
gpu_panel_power_X_delay_ms = gpu_panel_power_X_delay / 10
The register names gain a suffix `_ms` and calculation of the
destination register raw values gets done in gma code now.
Change-Id: Idf8e076dac2b3048a63a0109263a6e7899f07230
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48958
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
SoC will transmit the EoTp (End of Transmission packet) when
MIPI_DSI_MODE_EOT_PACKET flag is set.
Enabling EoTp will make the line time larger, so the hfp and
hbp should be reduced to keep line time.
BUG=b:168728787
BRANCH=kukui
TEST=Display is normal on Kukui
Signed-off-by: Shaoming Chen <shaoming.chen@mediatek.corp-partner.google.com>
Change-Id: Ifadd0def13cc264e9d39ab9c981fbdc996396bfa
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48868
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
Some bridge chip or panel requires dsi signal output before dsi
receiver works.
BUG=b:168728787
BRANCH=kukui
TEST=Display is normal on Kukui
Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
Change-Id: I3bded27087490f32ee233e615cfad1fd05fb582d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47380
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
Add the stdint.h header, and drop the GLIBC section from amdfwtool.h to build this tool on FreeBSD as well as Linux.
Signed-off-by: Idwer Vollering <vidwer@gmail.com>
Change-Id: I295fd308b0f5e2902931f02c9455823a614976de
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48977
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I1e63a419db92642df6b7956050c39540c2ae11d6
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48781
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I9d500be609d61ccf234260216bd5aae3f78e91a8
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48802
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The flash controller driver can be shared among mt8173 and mt819x.
TEST=boot to kernel on Asurada
boot to kernel on Hana (w/o BL31)
Change-Id: I4e5213563189336496122a0f2d8077b3e5245314
Signed-off-by: Yidi Lin <yidi.lin@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48972
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
|
|
Signed-off-by: Huayang Duan <huayang.duan@mediatek.com>
Change-Id: If200f4dcef0b1d0b7e901d4ae6e667b1f75156f5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44711
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
Signed-off-by: Huayang Duan <huayang.duan@mediatek.com>
Change-Id: I317451e41774e983c07566dc71c7ba8833c7f55e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44710
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
To get better PI linearity, perform 8 phase calibration to do
MCK 0/180/45 training and select the best PI settings.
Signed-off-by: Huayang Duan <huayang.duan@mediatek.com>
Change-Id: Ib4ccaa8d43b8382cbc64cf82de86ad1ac16cb89a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44709
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
Signed-off-by: Huayang Duan <huayang.duan@mediatek.com>
Change-Id: I08326cd1e6f7415d3a91d1591678e1b2c52c6781
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44708
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
which select INTEL_GMA_ACPI. Rework brightness level includes and
platform-level asl files to avoid duplicate device definition for GFX0.
Include gfx.asl for Skylake/Kabylake, since all other soc/intel/common
platforms already do. Adjust mb/51nb/x210 to prevent device redefinition.
Some OSes (e.g. Windows, MacOS) require/prefer the ACPI device for
the IGD to exist, even if ACPI brightness controls are not utilized.
This change adds a GFX0 ACPI device for all boards whose platforms
select INTEL_GMA_ACPI without requiring non-functional brightness
controls to be added at the board level.
Change-Id: Ie71bd5fc7acd926b7ce7da17fbc108670fd453e0
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48862
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
Adjust platform-level includes as needed.
Change-Id: I376349ccddb95c166f0836ec1273bb8252c7c155
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48959
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
eint event mask register is used to mask eint wakeup source on mt8192.
All wakeup sources are masked by default. Since most MediaTek SoCs do
not have this design, we can't modify the kernel eint upstream driver to
solve the issue 'Can't wake using power button (cros_ec) or touchpad'.
So we add a driver here to unmask all wakeup sources.
BUG=b:169024614
Signed-off-by: G.Pangao <gtk_pangao@mediatek.com>
Change-Id: I8ee80bf8302c146e09b74e9f6c6c49f501d7c1c4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46409
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Extract the architecture (-a) and package (-p) options into a
new variable (ARCH) to simplify the construction of BUILD_STR.
Test: build/boot various boards w/Tianocore payload
Change-Id: I490d48428ac56d613d0b704700dfcf4ebfb2d245
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48942
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add the right register values for backlight control to CNL's Kconfig.
To make iasl happy about the reversed register order, split the field.
Change-Id: I05a06cc42397c202df9c9a1ebc72fb10da3b10ec
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48772
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Replace the mainboard-specific code for "POST complete" signalling with
devicetree entries for using the newly introduced IPMI driver
functionality.
Test: Boot the machine via the BMC web interface and check that sensors
get read correctly by the IPMI firmware when the payload starts.
Tested successfully.
Tested-by: Johnny Lin <Johnny_Lin@wiwynn.com>
Change-Id: I3441c2a971cfb564b34b3a419beceb949fe295b1
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48672
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Configure the "POST complete" gpio in the devicetree for the BMC/IPMI
driver and set the pad's initial value to 0 since the signal is active-
high and shall be set by the IPMI/BMC driver.
Also add the pad to early gpio config, since it is expected to have an
external pull-up like X11SSM-F, which is wrong and would confuse the BMC.
Test: Boot the machine via the BMC web interface and check that sensors
get read correctly by the IPMI firmware when the payload starts.
Tested successfully.
Change-Id: If344b2271bfc8d50b8b64847109818f96f2abbcb
Tested-by: Patrick Rudolph <siro@das-labor.org>
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48711
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Configure the "POST complete" gpio in the devicetree for the BMC/IPMI
driver.
Also add the pad to early gpio config, since it has an external pull-up,
which is wrong and would confuse the BMC. Set the pad's initial value to
zero since the "POST complete" signal is active-high and shall be set by
the IPMI/BMC driver.
Test: Boot the machine via the BMC web interface and check that sensors
get read correctly by the IPMI firmware when the payload starts.
Tested successfully.
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: I6409b2aca90585e44ee5d32df0ae73b259443f32
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48097
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Set `bmc_jumper_gpio` to the JPB1 gpio to enable/disable BMC/IPMI
according to its value.
Test: Boot with jumper set to each enabled and disabled and check debug
log if IPMI gets enabled/disabled accordingly.
Tested successfully.
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: I8581556d915cbad2c743a79db273479ba55798fb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48095
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Some server boards like OCP Tiogapass and X11-LGA1151 boards use a gpio
for signalling "POST complete" to BMC/IPMI. Add a new driver devicetree
option to set the gpio and configure a callback that pulls the gpio low
right before jumping to the payload.
Test: Check that sensor readings appear in BMC web interface when the
payload gets executed.
Successfully tested on Supermicro X11SSM-F with CB:48097, X11SSH-TF with
CB:48711 and OCP DeltaLake with CB:48672.
Change-Id: I34764858be9c7f7f1110ce885fa056591164f148
Tested-by: Johnny Lin <Johnny_Lin@wiwynn.com>
Tested-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: Patrick Rudolph <siro@das-labor.org>
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48096
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Some boards, like the Supermicro X11SSM-F, have a jumper for enabling or
disabling the BMC and IPMI. Add a new devicetree driver option to set
the GPIO used for the jumper and enable or disable IPMI according to its
value.
This gets used in a follow-up change by Supermicro X11SSM-F.
Test: Boot with jumper set to each enabled and disabled and check debug
log if IPMI gets enabled/disabled accordingly.
Successfully tested on Supermicro X11SSM-F with CB:48095.
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: Icde3232843a7138797a4b106560f170972edeb9c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48094
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
This change adds the required gpio operations struct to soc/common gpio
code and hooks them up in all socs currently using the gpio block code,
except DNV-NS, which is handled in a separate change.
Also, add the gpio device to existing chipset devicetrees.
Successfully tested on Supermicro X11SSM-F with CB:48097, X11SSH-TF with
CB:48711 and OCP DeltaLake with CB:48672.
Change-Id: I81dbbf5397b28ffa7537465c53332779245b39f6
Tested-by: Johnny Lin <Johnny_Lin@wiwynn.com>
Tested-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: Patrick Rudolph <siro@das-labor.org>
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48583
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This reverts commit 5bb5c43b936f0bb01e08a71df1865343d7be9b88.
Reason for revert: Build bot fails.
Change-Id: I8f022514351b37be135d10ef8486e4aa5fd6361b
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48980
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
