| Age | Commit message (Collapse) | Author |
|---|
|
The MT817x display output pipeline can be configured to drive an 8-lane
MIPI/DSI panel using "dual DSI" mode. For the "dual DSI" video data path,
the UFO block is configured to reorder the data stream into left and right
halves which are then sent by the SPLIT1 block to the DSI0 and DSI1
respectively. The DSI0 and DSI1 outputs are then synchronously clocked at
half the nominal data rate by their respective MIPI_TX0/MIPI_TX1 phys.
Also, update the call sites in oak mainboard to avoid build breakage.
BRANCH=none
BUG=b:35774871
TEST=Boot Rowan in developer mode and see output on the panel
Change-Id: Id47dfd7d9e98689b54398fc8d9142336b41dc29f
Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-on: https://review.coreboot.org/19361
Tested-by: build bot (Jenkins)
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
This helper function was introduced so that mainboards don't need
to manually fill in these struct edid fields.
BRANCH=none
BUG=b:35774871
TEST=Boot Rowan in developer mode and see output on the panel
Change-Id: Ic9404a786a28b314b710e037dcae776be4b584ca
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-on: https://review.coreboot.org/19388
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
The SD/MMC support is broken into several pieces. There are three main
data structures:
* sdhci_ctrlr - This is SDHCI controller specific and defined in
include/device/sdhci.h
* sd_mmc_ctrlr - This contains generic controller management data and
defined in include/device/sd_mmc_ctrlr.h
* storage_media - This contains the flash storage device management data
and is defined in include/device/storage.h
The SD/MMC driver consists of several components:
* SDHCI controller code
* bouncebuf.c
* bouncebuf.h
* pci_sdhci.c
* sdhci.c
* sdhci.h
* sdhci_adma.c
* sdhci_display.c
* Flash storage device support
* mmc.c
* mmc.h
* sd.c
* sd_mmc.c
* sd_mmc.h
* storage.c
* storage.h
* storage_erase.c
* storage_write.c
Kconfig values enable various portions of the controller and storage
drivers to be built to reduce the overall size of what is included in
the final image.
Full read/write/erase operations are provided for those platforms which
want to take advantage. It is also possible to build the driver to
perform initialization only. By default, this driver is not included in
any platform, platforms must specifically select DRIVERS_STORAGE to add
the SD/MMC support.
After this patch is reviewed and merged, there are some additional
patches:
* Common CAR storage area - Use a predefined region of CAR to pass data
structures between bootblock through to romstage. This allows early
stages to preform the SD/MMC device initialization and later stages
to use the SD/MMC device without further initialization. The example
code initializes the SD/MMC device in bootblock and uses the SD/MMC
device in romstage without further initialization.
* CBMEM ID - Add a CBMEM ID value for the data structures so that they
may be passed from romstage to ramstage and eventually the payload.
The example uses the SD/MMC device in ramstage without further
initialization.
* Move the SD/MMC driver into commonlib
* Have libpayload build the SD/MMC driver from commonlib. The intent
is to pass the controller state to libpayload so that the SD/MMC
device can be used without further initialization.
* On some platforms, have depthcharge use the commonlib SD/MMC driver
History:
Copy the SD/MMC driver from depthcharge revision eb583fa8 into coreboot
and make the following changes:
* Removed #include "config.h" from mmc.c, allow the lint tests to pass.
* Move include files from drivers/storage into include/device.
* Rename mmc.h to storage.h.
* Add the Kconfig and Makefile and make edits to get the code to build.
* Add support to initialize a PCI controller.
* Fix formatting issues detected by checkpatch.
* Fix data flow issues detected by checkpatch.
* Add the missing voltage (MMC_VDD_35_36) into the voltage mask.
* Rename the macros mmc_debug, mmc_trace and mmc_error to sd_mmc_*.
* Replace printf with sd_mmc_error.
* Add sdhc_debug, sdhc_trace and sd_error macros.
* Add Kconfig values to enable storage device debugging and tracing.
* Add tracing and debug support to the SDHCI driver.
* Allow SOC to override more controller features.
* Split out ADMA support.
* Move 1V8 support into SOC routine.
* Move HS400 support into SOC routine.
* Rework clock handling.
* Change all controller references to use ctrlr.
* Update the voltage handling.
* Update modes of operation.
* Move DMA fields into MmcCtrlr.
* Update bus width support.
* Change MMC_TIMING_* to BUS_TIMING_*.
* Rename MMC_MODE_ to DRVR_CAP.
* Move quirks into ctrlr->caps.
* Associate removeable with the controller.
* Statically allocate MmcMedia.
* Replace the SdhciHost structure with the MmcCtrlr structure.
* Split the code to support other SD/MMC controllers.
* Split out erase and write support.
* Update the code to be more consistent with the coreboot coding style.
* Only expose calling APIs.
* Divide up mmc.c into 4 modules: MMC, SD, storage card, common code.
* Update debug and error messages.
* Add partition support.
* Display clock frequencies once in MHz.
* Remove mmc_send_cmd, use ctrlr->send_cmd instead.
* Handle error from sd_send_op_cond.
* Allow mainboard to control delays around CMD 0.
* Support command logging.
* Mainboard may set delay after SD/MMC command.
* Display serial number with sd_mmc_trace.
* Remove cmd set parameter from mmc_switch.
* Display errors for timeout and comm errors.
* Add LED support.
* Move 64bit DMA flag into ctrlr->caps.
* Rework PIO transfer routine.
* Add HS200 bus tuning.
* Add support for HS400.
* Use same format for HS400, HS200 and HS52.
* Reduce storage_media structure size
* Add routine to update code pointers
* Add display of storage setup
* Display controller setup
TEST=Build and run on Reef and Galileo Gen2
Change-Id: I9b5f9db1e27833e4ce4a97ad4f5ef3a46f64f2a2
Signed-off-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-on: https://review.coreboot.org/19208
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Add a Kconfig value to indicate coreboot builds.
Add prototypes and definitions for:
* dma_coherent
* dma_malloc
* xmalloc
* xzmalloc
Move prototype for memset into stdlib.h from string.h to eliminate build
breaks.
TEST=Build and test on Galileo Gen2
Change-Id: Ib2eb2ca143b0538bdd1863e628af4c1948bc0f8c
Signed-off-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-on: https://review.coreboot.org/19207
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
This patch enables TPM2 using cr50 over I2C for the Rowan board, and
adds an mt8173 specific TPM IRQ polling function. The function relies on
the appropriate EINT input configured to trigger the ready status on
the rising edge.
The cr50 TPM is on I2C address 0x50.
The cr50 interrupt GPIO is also made available for use by depthcharge
via the coreboot tables.
BRANCH=none
BUG=b:36786804
TEST=Boot rowan w/ serial enabled, verify coreboot and depthcharge are
configured to use IRQ flow control when talking to the Cr50 TPM.
Change-Id: If6cdd0e39e4ac86538f27f322c55c329179ee084
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-on: https://review.coreboot.org/19364
Tested-by: build bot (Jenkins)
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Add basic support to configure GPIOs to poll for external interrupts
(EINT).
BRANCH=none
BUG=b:36786804
TEST=Boot rowan w/ serial enabled, verify coreboot and depthcharge are
configured to use IRQ flow control when talking to the Cr50 TPM.
Change-Id: I9d52591661a5a74ec1fd9a081f606f0a08a3a6ab
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-on: https://review.coreboot.org/19362
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins)
|
|
The vendor.irq field was originally intended for use as the TPM 1.2
"command complete" interrupt. However, all actual coreboot tpm drivers
and hardware use the vendor.status method of checking command completion
instead, and this irq field is not used.
Let's just remove this unused functionality to simplify the code.
BRANCH=none
BUG=b:36786804
TEST=Boot reef w/ serial enabled firmware, verify verstage sees
"cr50 TPM" and does not complain about lack of tis_plat_irq_status().
TEST=Boot eve w/ serial enabled firmware, verify verstage sees
"cr50 TPM" and does not complain about lack of tis_plat_irq_status().
Change-Id: I994c5bfbd18124af9cb81d9684117af766ab0124
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-on: https://review.coreboot.org/19396
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Philippe Mathieu-Daudé <philippe.mathieu.daude@gmail.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
|
|
DRIVER_TPM_I2C_IRQ has been removed. TPM_TIS_ACPI_INTERRUPT now specifies
the TPM2 ACPI interrupt used by intel's tis_plat_irq_status() routine.
BRANCH=none
BUG=b:36786804
TEST=Boot reef w/ serial enabled firmware, verify verstage sees
"cr50 TPM".
Change-Id: If66a2a1d461a411e112589c84a434066d48b9399
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-on: https://review.coreboot.org/19410
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
|
|
DRIVER_TPM_I2C_IRQ has been removed. TPM_TIS_ACPI_INTERRUPT now specifies
the TPM2 ACPI interrupt used by intel's tis_plat_irq_status() routine.
BRANCH=none
BUG=b:36786804
TEST=Boot eve w/ serial enabled firmware, verify verstage sees
"cr50 TPM".
Change-Id: Ia1eacd15e71a46a37457ee2f117b156393c3393d
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-on: https://review.coreboot.org/19409
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
|
|
The Cr50 TPM uses an IRQ to provide a "status" signal used for hand-shaking
the reception of commands. Real IRQs are not supported in firmware,
however firmware can still poll interrupt status registers for the same
effect.
Commit 94cc485338a3 ("drivers/i2c/tpm/cr50: Support interrupts for status")
added support for the Cr50 driver on X86 platforms to use a KConfig file
to supply an IRQ which it would poll using acpi_get_gpe. If the IRQ is
not supplied, the Cr50 driver inserts a 20 ms wait.
Unfortunately this doesn't work so well when using the i2c connected Cr50
on ARM platforms. Luckily, a more generic implementation to allow a
mainboard to supply a Cr50 IRQ status polling function was solved for SPI
connected Cr50s by commit 19e3d335bddb ("drivers/spi/tpm: using tpm irq to
sync tpm transaction").
Let's refactor the i2c c50 driver to use this same approach, and change
eve and reef boards to make use of DRIVER_TPM_TIS_ACPI_INTERRUPT for
specifying the TPM flow control interrupt.
This essentially reverts these two commits:
48f708d199 drivers/i2c/tpm/cr50: Initialize IRQ status handler before probe
94cc485338 drivers/i2c/tpm/cr50: Support interrupts for status
And ports this commit to i2c/tpm/cr50:
19e3d335bd drivers/spi/tpm: using tpm irq to sync tpm transaction
As a side effect the tpm_vendor_specific IRQ field goes back to its
original usage as the "TPM 1.2 command complete" interrupt, instead of
being repurposed to hold the flow control IRQ.
BRANCH=none
BUG=b:36786804
TEST=Boot reef w/ serial enabled firmware, verify verstage sees
"cr50 TPM" and does not complain about lack of tis_plat_irq_status().
TEST=Boot eve w/ serial enabled firmware, verify verstage sees
"cr50 TPM" and does not complain about lack of tis_plat_irq_status().
Change-Id: I004329eae1d8aabda51c46b8504bf210484782b4
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-on: https://review.coreboot.org/19363
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
|
|
TPM_TIS_ACPI_INTERRUPT specifies the TPM2 ACPI interrupt used by intel's
tis_plat_irq_status() routine.
BRANCH=none
BUG=b:36786804
TEST=Boot reef w/ serial enabled firmware, verify verstage sees
"cr50 TPM".
Change-Id: Ic69add8a3ce35be64fb37db4ed40163f6144fc9c
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-on: https://review.coreboot.org/19408
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
|
|
TPM_TIS_ACPI_INTERRUPT specifies the TPM2 ACPI interrupt used by intel's
tis_plat_irq_status() routine.
BRANCH=none
BUG=b:36786804
TEST=Boot eve w/ serial enabled firmware, verify verstage sees
"cr50 TPM".
Change-Id: Ifeb09a0a35bff7cd9091f6d027f0065288ca35c9
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-on: https://review.coreboot.org/19407
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
|
|
Utilize the intel/common code for tis_plat_irq_status() to remove
dependencies and code duplication on for bringing up a board
requiring tis_plat_irq_status().
Change-Id: I2aaa1d7d3ce171dc1788438ff9990fce533deb6c
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/19371
Tested-by: build bot (Jenkins)
|
|
On Intel platforms utilizing the CR50 TPM the interrupts are routed
to GPIOs connected to the GPE blocks. Therefore, provide a common
implementation for tis_plat_irq_status() to reduce code duplication.
This code could be further extended to not be added based on
MAINBOARD_HAS_TPM_CR50, but that's all that's using it for now.
Change-Id: I955df0a536408b2ccd07146893337c53799e243f
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/19369
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins)
|
|
The CR50 TPM can do both SPI and I2C communication. However,
there's situations where policy needs to be applied for CR50
generically regardless of the I/O transport. Therefore add
MAINBOARD_HAS_TPM_CR50 to encompass that. Additionally,
once the mainboard has selected CR50 TPM automatically select
MAINBOARD_HAS_TPM2 since CR50 TPM is TPM 2.0.
Change-Id: I878f9b9dc99cfb0252d6fef7fc020fa3d391fcec
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/19370
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins)
|
|
MAINBOARD_HAS_SPI_TPM_CR50 describes a capability of the board and SPI_TPM
is only on if we actually want to compile in the TPM code. For example,
in src/drivers/i2c/tpm/Kconfig MAINBOARD_HAS_I2C_TPM_CR50 also doesn't
depend on SPI_TPM.
This problem manifests itself as the following build issue when building
with MAINBOARD_HAS_I2C_TPM_CR50 but without an explict "select TPM2":
src/Kconfig:296:error: recursive dependency detected!
src/Kconfig:296: symbol MAINBOARD_HAS_TPM2 is selected by MAINBOARD_HAS_TPM_CR50
src/Kconfig:408: symbol MAINBOARD_HAS_TPM_CR50 depends on MAINBOARD_HAS_SPI_TPM_CR50
src/drivers/spi/tpm/Kconfig:15: symbol MAINBOARD_HAS_SPI_TPM_CR50 depends on SPI_TPM
src/drivers/spi/tpm/Kconfig:1: symbol SPI_TPM depends on TPM2
src/Kconfig:396: symbol TPM2 is selected by MAINBOARD_HAS_TPM2
MAINBOARD_HAS_SPI_TPM_CR50 shouldn't depend on SPI_TPM.
BRANCH=none
BUG=b:36786804
TEST=Boot rowan w/ serial enabled, verify coreboot and depthcharge are
configured to use IRQ flow control when talking to the Cr50 TPM.
Change-Id: I0cb3f6d3aa4159bad563a6a4b006d7f4825e04b4
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Suggested-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/19411
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Change-Id: Id1b7b98b4fba745ac0d55638b6a5cceba3c329ef
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/19415
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
TESTED on D510MO.
Change-Id: I05aa40df0d2a090fcf734416669e9e1bbff094e4
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/19414
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
For raminit to succeed on a hot reset the following things are
prevented from running:
* Clearing self refresh
* Setting memory frequency
* programming sdram dll timings
* programming rcomp
TESTED on Intel d510mo.
Change-Id: I8f7e5c2958df29a96cdf856ade2f4f33707ad362
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/19337
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
There is no need to override CBFS_SIZE since there is no additional
firmware needed on the flash.
Also due to it having a description CBFS_SIZE was displayed twice in
menuconfig, which is fixed by this.
Change-Id: I1a8e2e458ac4d420f3fd4628c2805b6d4e2ee529
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/19331
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Tested on X230 with an external screen connected to every one of the
DP ports (miniDP on mainboard, two DP ports on dock), the GRUB payload
can display on both the external screen and the internal LVDS screen.
This is a copy-paste of I8e02c8003ff745d05ee272c59377174847f5219c.
Change-Id: I8f270d558668c1fe41bcdcc7d6d2aa7f053c85b6
Signed-off-by: Iru Cai <mytbk920423@gmail.com>
Reviewed-on: https://review.coreboot.org/19412
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Lid switch is not available.
Hence report lid state as always open.
Change-Id: Ia9c82c3ad323912bad51cf55ed80a37b3110b1ef
Signed-off-by: Naresh G Solanki <naresh.solanki@intel.com>
Reviewed-on: https://review.coreboot.org/19219
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
|
|
Configure PCI root port as per schematic.
Change-Id: I10ef682e8c54e22f328db5105d4da39c72ac2bed
Signed-off-by: Naresh G Solanki <naresh.solanki@intel.com>
Reviewed-on: https://review.coreboot.org/19390
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Add CPUID, IGD, MCH & LPC ID of Kabylake-R.
Change-Id: I5ee7b3a2616f71137bba83c071288dbda2acde3d
Signed-off-by: Naresh G Solanki <naresh.solanki@intel.com>
Reviewed-on: https://review.coreboot.org/19218
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Balaji Manigandan <balaji.manigandan@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Use spi_setup_slave to fill up the spi_slave structure with
pointer to spi_ctrlr structure which can then be used to perform all
spi operations.
Change-Id: I2804ed1e85402426a654352e1ceaf0993546cd8b
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/19385
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Philippe Mathieu-Daudé <philippe.mathieu.daude@gmail.com>
|
|
member_size macro provides the size of a structure member.
Change-Id: I53e9c9bf70b3ebed0d15e8258111b17e50667a74
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/19384
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Philippe Mathieu-Daudé <philippe.mathieu.daude@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Depend on I2C_TPM to prevent showing the menu entry on systems
that do not have an I2C TPM installed.
Change-Id: I7cd647c9c7e9721eab96ab64b844a882f156ee68
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/19374
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Philippe Mathieu-Daudé <philippe.mathieu.daude@gmail.com>
|
|
Change-Id: If5e255c75e7774393ef7e4febef84d97a1a3a118
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-on: https://review.coreboot.org/19366
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Philippe Mathieu-Daudé <philippe.mathieu.daude@gmail.com>
|
|
This brings in 2 new commits from the upstream cbootimage
repository, merged to the upstream tree April 12, 2016 and
July 28, 2016
64045f9 bct_dump: don't crash on devices without RSA support
ea1e03d sign.sh: Add more features
Change-Id: I3b6c0c2c855044d7fce87eff9954bce5035ca966
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/18955
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Change-Id: Ib95a7c9c64c481af7dcf1074ffc0fc76dc6b6ff9
Signed-off-by: Martin Roth <gaumless@gmail.com>
Reviewed-on: https://review.coreboot.org/19144
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Philippe Mathieu-Daudé <philippe.mathieu.daude@gmail.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Read DRAM SPD and populate MemorySpdPtr fields
in UPD data structure for FSP.
BUG=b:36490168, b:35775024
BRANCH=None
TEST=./util/abuild/abuild -p none -t google/fizz -x -a
We are currently working on bringup and have no
hardware to test on yet.
Change-Id: I191cc6bf1fd8aa461855c538b48fd39e3ffd7848
Signed-off-by: Shelley Chen <shchen@chromium.org>
Reviewed-on: https://review.coreboot.org/19205
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
This board was added while the latest libgfxinit changes were in review.
Update to make it compile again and sanitize the port list.
Change-Id: I81b96e225945a8f8e47b64cefea91eb2747675ca
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/19353
Tested-by: build bot (Jenkins)
Reviewed-by: Nicola Corna <nicola@corna.info>
|
|
TPM ACPI entries are automatically generated, and the old static
TPM ASL file is obsolete. Remove the reference to this obsolete
static and empty ASL file.
Delete src/drivers/pc80/tpm/acpi/tpm.asl.
Change-Id: I6163e6d59c53117ecbbbb0a6838101abb468de36
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/19291
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
MMA blobs internal version 2.1018 adds more tests.
This patch updates the script to accommodate that
change. MMA blobs are part of chrome private
repository.
Change-Id: Iff660fdfdfcd7acc3820c5550740276be6213877
Signed-off-by: Pratik Prajapati <pratikkumar.v.prajapati@intel.com>
Reviewed-on: https://review.coreboot.org/19259
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Clean up NGI code now that libgfxinit has replaced old C code:
- replace #if preprocessor guards with if (IS_ENABLED(...))
- don't guard variable declarations
- remove code that would only be executed for old NGI / isn't
used by libgfxinit
Test: boot google/wolf with VBIOS, NGI, and UEFI/GOP video init,
observe payload and pre-OS graphics display functional.
Change-Id: I96e74f49ea70e09cbac6f8af561de3e18fa7d260
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/19327
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Philippe Mathieu-Daudé <philippe.mathieu.daude@gmail.com>
|
|
Use the iobuf API instead of relying on own buffer management. It
also provides consistency between marshaling and unmarshaling code
paths for propagating return values instead of overloading the values
of existing variables.
BUG=b:36598499
Change-Id: Iec0bbff1312e8e6ec616d1528db8667f32e682c9
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/19063
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Introduce ibuf and obuf structures for helping manage memory buffers.
The ibuf, an input buffer, can be read from and the obuf, an output
buffer, can be written to. Helper functions are provided for serializing
values in different endian formats. This library is provided to for
common buffer management routines such that the same code doesn't
have to re-written in different and less consistent forms.
BUG=b:36598499
Change-Id: I5247237f68b658906ec6916bbbb286d57d6df5ee
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/19062
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Philippe Mathieu-Daudé <philippe.mathieu.daude@gmail.com>
|
|
- Refactor the spec & setter file reads into a separate function.
- Make sure files can actually be opened before reading from them.
- Check all malloced variables.
- Set functions with no declatations as static.
- Update blobtool.tab.c_shipped to the latest version.
Change-Id: Ie97fff84493a06f48d8673d388c3882028d048ca
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/19231
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
- Rewrite STRING and COMMENT expressions to remove need for CHARS.
- Clean up regular expressions - get rid of unnecessary expressions.
- Remove extra newline from the end of the file.
- Clean up stripquotes() function
-- Remove unnecessary backslashes in '\"'
-- Check malloc for failure
-- Remove unnecessary assignment of 0 to the end of the new string,
snprintf will take care of it.
- Update blobtool.lex.c_shipped to the new version.
Change-Id: I002962cfae0816ed3c7a5811dfb1b8b48fdc5729
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/19230
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
The function decode_spd uses undeclared variables and an incorrectly
initialized array.
Change-Id: Ib45a8b2946c04c270e29524675b1f09d491d282b
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/19336
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Philippe Mathieu-Daudé <philippe.mathieu.daude@gmail.com>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
In the single GPU configuration, the T420 has an LVDS port, one DP++
and one VGA port connected to the IGD. Docking solutions feature up to
two additional DP/DVI-D ports, also directly connected to the IGD.
This makes the list of ports to probe pretty long (takes about 70ms
if nothing but LVDS is connected). We could save about 20~30ms if we'd
limit the ports in case we are not docked or have a discrete GPU.
Change-Id: I8e02c8003ff745d05ee272c59377174847f5219c
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/19378
Tested-by: build bot (Jenkins)
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
This commit changes the interrupt configuration for the touchpad to be
level triggered so it matches what the device is actually using.
When the system wakes from suspend by way of touchpad interrupt, or
there is touchpad input while in suspend that does not wake the device
(when the device is in tablet mode) the interrupt edge is not seen by
the AP so the driver does not handle the event and the touchpad keeps
the interrupt asserted and does not send further interrupts. The end
result is a non-functional touchpad after resume until it is reset or
the driver is reloaded.
This happens because the touchpad is actually treating the interrupt as
level triggered and expects the kernel driver to read a data packet over
I2C before it will de-assert the pending interrupt.
BUG=b:35774857
BRANCH=none
TEST=Test that the system can reliably wake from suspend by touchpad
event via the EC and continue to have a functional touchpad after resume.
Change-Id: Iaf7c04d9bc9d945bdcc196dff54c92a2a68368f3
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/19382
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This patch allows the CBMEM console to persist across reboots, which
should greatly help post factum debugging of issues involving multiple
reboots. In order to prevent the console from filling up, it will
instead operate as a ring buffer that continues to evict the oldest
lines once full. (This means that if even a single boot doesn't fit into
the buffer, we will now drop the oldest lines whereas previous code
would've dropped the newest lines instead.)
The console control structure is modified in a sorta
backwards-compatible way, so that new readers can continue to work with
old console buffers and vice versa. When an old reader reads a new
buffer that has already once overflowed (i.e. is operating in true ring
buffer mode) it will print lines out of order, but it will at least
still print out the whole console content and not do any illegal memory
accesses (assuming it correctly implemented cursor overflow as it was
already possible before this patch).
BUG=chromium:651966
TEST=Rebooted and confirmed output repeatedly on a Kevin and a Falco.
Also confirmed correct behavior across suspend/resume for the latter.
Change-Id: Ifcbf59d58e1ad20995b98d111c4647281fbb45ff
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/18301
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Issue TPM startup on romstage completion via common LPC TPM
code if the TPM was enabled in Kconfig.
Change-Id: Id886d6aeefa045fb979f128b1cf4c10fff243b24
Signed-off-by: Timothy Pearson <tpearson@raptorengineering.com>
Reviewed-on: https://review.coreboot.org/19338
Tested-by: build bot (Jenkins)
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Kevin's center logic isn't super clean so it needs 925 mV for center
logic. All newer gru variants only need 900 mV.
BRANCH=gru
BUG=b:37429075
TEST=Reboot tests
Change-Id: I8c3bd6c245700b23c27cd5758c35c9993f801cb4
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/479463
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/19357
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
It seems that we should only ever run at 900mV on center logic.
Changing it to 950mV before might have just masked over problems that
are now fixed.
BRANCH=none
BUG=chrome-os-partner:56940
TEST=on kevin, run
stressapptest -M 1536 -s 1000
Change-Id: I5a09b1b403df800396bb2f2e8c76d14a4519d44a
Signed-off-by: Derek Basehore <dbasehore@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/391032
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Commit-Queue: Lin Huang <hl@rock-chips.com>
Tested-by: Lin Huang <hl@rock-chips.com>
Reviewed-on: https://review.coreboot.org/19356
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
|
|
Move include of reg_access.h from pci_devs.h to reg_access.c.
TEST=Build and run on Galileo Gen2
Change-Id: I0d2de96f51c56001cdd06c7974cbc649fde1e89c
Signed-off-by: Lee Leahy <Leroy.P.Leahy@intel.com>
Reviewed-on: https://review.coreboot.org/19355
Tested-by: build bot (Jenkins)
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
|
|
When console input driver registers itself, perform flush of input
buffer to avoid interpreting any stale key presses before libpayload
is run.
keyboard.c: Remove the redundant buffer flush.
8250.c: Ensure that serial_hardware_is_present is set before call to
add input driver.
BUG=b:37273808
TEST=Verified that any key presses in serial console before payload is
up do not have any effect after the payload starts running.
Change-Id: I46f1b6715ccf6418f5b2c741bf90db2ece26a60d
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/19345
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Create Soraka board which derives from Poppy, a KBL reference board.
More Soraka specific changes need to be done later on.
BRANCH=master
BUG=b:36995255
TEST=Build (as initial setup)
Change-Id: I8af68d2cf475df56336aa0e3bebe86a54ece1999
Signed-off-by: YH Lin <yueherngl@chromium.org>
Reviewed-on: https://review.coreboot.org/19343
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Move current NHLT configuration implementation to baseboard so that
variants can leverage it or provide their own configuration.
BUG=b:37375693
Change-Id: I2a4317c112f9e3614bd01eb6809727b73328d29d
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/19326
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Add support for memory configuration by providing weak implementation
from the baseboard. All SPD files are present under spd/
directory. SPD_SOURCES must be provided by the variants to ensure that
required SPD hex files are included in the SPD binary.
BUG=b:37375693
Change-Id: Ic9bcc03d5a35bebd14061680f264ac072b3c0634
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/19325
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Add support for ChromeOS GPIO ACPI table information by providing weak
implementation from the baseboard.
BUG=b:37375693
Change-Id: I641afe6bb45f106ddebde081a8ac2c64278ebeb9
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/19324
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Provide APIs for board_id() and gpio table functionality. Default weak
implementations are provided from the baseboard.
BUG=b:37375693
Change-Id: Ic3c946e6cb12b3c8ef3e83a1037ed0fc8cffbded
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/19323
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
In order to be able to share code across different poppy variants,
provide the concept of baseboard and variants. New directory layout:
variants/baseboard - code
variants/baseboard/include/baseboard - headers
variants/poppy - code
variants/poppy/include/variant - headers
New boards would then add themselves under their board name within
"variants" directory.
This is purely an organizational change.
BUG=b:37375693
Change-Id: If6c1c5f479cfffe768abf27495d379744104e2dc
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/19322
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Clean up Kconfig file in order to support variants for poppy. Add
BOARD_GOOGLE_BASEBOARD_POPPY that can be set by various poppy variants
to use the common baseboard configs.
BUG=b:37375693
Change-Id: I399ecc8c3efb3af26e1fcf60fe2c75b24769fc0f
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/19321
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Change-Id: Ib92550fe755293ce8c65edf59242a2b04327128e
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/19332
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Philippe Mathieu-Daudé <philippe.mathieu.daude@gmail.com>
|
|
Hide some (partial) lines behind DEBUG_RAM_SETUP and shorten
some messages. This saves some KiB to make CBMEM console more
usable in romstage.
Change-Id: I62a84ca662ee778b7c1deb71247f3b01a37858fa
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/19318
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Add camera related support
* Enable the SA Imaging Unit and CIO2 devices.
* Enable TPS68470 PMIC and populate related ACPI objects.
* Enable OV cameras and populate related ACPI objects.
* Enable Dongwoon AF DAC and populate related ACPI objects.
BUG=b:36580624
BRANCH=none
TEST=Build and boot poppy. Dump and verify that ACPI tables
have the required entries for all the camera devices.
Change-Id: Ifbe878bb6b25fc976e935fee16c4d59fadd47fe2
Signed-off-by: Sowmya V <v.sowmya@intel.com>
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/18969
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
|
|
Add SSDT generator for MIPI CSI camera to create ACPI objects
used by the Intel kernel drivers.
* SSDB: Sensor specific database for camera sensor.
* PWDB: Power database for all the camera devices.
* CAMD: ACPI object to specify the camera device type.
BUG=b:36580624
BRANCH=none
TEST=Build and boot poppy. Dump and verify that the generated SSDT table
has the required entries.
Change-Id: Ief9e56d12b64081897613bf1c7abcdf915470b99
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Signed-off-by: Sowmya V <v.sowmya@intel.com>
Reviewed-on: https://review.coreboot.org/18967
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins)
|
|
This patch includes ipu.asl file in the main DSDT definition
to add ACPI entries for IMGU and CIO2 devices.
BUG=b:36580624
BRANCH=none
TEST=Build and boot poppy. Dump and verify that DSDT table
has the entries for IMGU and CIO2 devices.
Change-Id: Ib7485315cb9468da7c6aa090862657a265121493
Signed-off-by: Sowmya V <v.sowmya@intel.com>
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/19110
Tested-by: build bot (Jenkins)
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Add ASL entries for IMGU and CIO2 devices
* _CCA ACPI object to report that there is no Cache Coherent DMA support.
* CAMD ACPI object to specify the device type.
These ACPI objects are used by Intel kernel drivers.
BUG=b:36580624
BRANCH=none
TEST=Build and boot poppy. Dump and verify that DSDT table
has the entries for IMGU and CIO2 devices.
Change-Id: I13050253e18408cdb1e196f8003b3f43299aa5a5
Signed-off-by: Sowmya V <v.sowmya@intel.com>
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/18968
Tested-by: build bot (Jenkins)
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
We're already reading the RTC whenever we file an event, we might as
well print out the value at that time. Having a few RTC timestamps in
the firmware log makes it easier to correlate that part of the log to a
particular boot once we start having multiple boots in the log.
Change-Id: I750dd18aa2c43c95b8c1fbb8f404c1e3a77bec73
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/19305
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
1. Update formatting of gpio table to fit everything within 80 column
limit.
2. PEN_RESET gpio is non-existent. Get rid of it.
BUG=b:37375693
Change-Id: I1bcc4168659f365547e5f7227df8659e4bc7f243
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/19320
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Enable lower power state when running on battery. Deep S3 is not
enabled when in AC mode to support standard "docked" config.
BUG=b:36087058,b:36723679
TEST=Verified following behavior with USB mouse:
1. If AC is connected when entering S3, USB mouse is able to wake up.
2. If AC is not connected when entering S3, USB mouse does not wake up.
3. If AC is connected when entering S3 and removed after entering S3,
USB mouse does not wake up.
4. If AC is not connected when entering S3 and attached after entering
S3, USB mouse does not wake up.
Change-Id: I141a8d4779de004e27fcd9357cef787a38a27b24
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/19276
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Don't start counting the buffer size amidst the BufferSize field
itself. This should help with a regression introduced in Linux
with [1] which checks the BufferSize field.
[1] https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=57707a9a778
Change-Id: I7349c8e281c41384491d730dfeac3336f29992f7
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/19284
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
TPM ACPI entries are automatically generated, and the old static
TPM ASL file is obsolete. Remove the reference to this obsolete
static ASL file.
Change-Id: I3cb2a8a3ac337d1de8a3c394d7a28155597239d0
Signed-off-by: Timothy Pearson <tpearson@raptorengineering.com>
Reviewed-on: https://review.coreboot.org/19283
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
|
|
Adds the necessary plumbing for acpi_device_path() to find the LPC
bridge on the AMD Family10h/15h northbridges and SB700 southbridge.
This is necessary for TPM support since the acpi path to the LPC bridge
doesn't match the built-in default in tpm.c
This is a port of GIT hash d8a2c1fb by Tobias Diedrich.
BUG=https://ticket.coreboot.org/issues/102
Change-Id: I1c514e335e194b2864599e5419cfaee830b94e38
Signed-off-by: Timothy Pearson <tpearson@raptorengineering.com>
Reviewed-on: https://review.coreboot.org/19282
Tested-by: build bot (Jenkins)
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Commit bf264e94 (i945:) adds a PCI reset to the romstage, and commit
bc8613ec (Fix i945 based boards) fixes that to use the correct
delay of 200 ms. This code was then copied over, when adding support for
the Lenovo T60.
The reset was related to the shipped crypto card on the Roda RK886EX and
Kontron 986LCD-M, so is not needed on the Lenovo T60. So remove it, to
reduce the boot time by 200 ms.
The same change is done for the Lenovo X60 in commit 7676730b
(mb/lenovo/x60: Remove PCI reset code from romstage).
Change-Id: Ifff43f095a1236c9e9a9ef0687e8efe42e72c971
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: https://review.coreboot.org/19298
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Certain devices, such as the northbridge on AMD Opteron systems,
do not require a node in the ACPI device path. Allow such devices
to be passed over by the ACPI path generator if the device-specific
ACPI name function returns a zero-length (non-NULL) string.
Change-Id: Iffffc9a30b395b0bd6d60e411439a437e89f554e
Signed-off-by: Timothy Pearson <tpearson@raptorengineering.com>
Reviewed-on: https://review.coreboot.org/19281
Tested-by: build bot (Jenkins)
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
CBGFX currently doesn't support portrait screens at all. This will have
to be fixed eventually but might take a bit of effort. As a first step
to make devices with a portrait panel somewhat usable, this patch will
just force a square canvas on these panels and keep the bottom part of
the screen black.
Also switch set_pixel to calculate framebuffer position via
bytes_per_line instead of x_resolution. This is supposed to be the
canonical way to do that and may differ in cases where the display
controller requires a certain alignment from framebuffer lines.
Change-Id: I47dd3bf95ab8a7d8b7e1913e0ddab346eedd46f1
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/19279
Tested-by: build bot (Jenkins)
Reviewed-by: Daisuke Nojiri <dnojiri@chromium.org>
|
|
Don't #include *. but use linker.
Change-Id: I716b37e71ab3a4409709357f50f79e3149ede2b6
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/19027
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Change-Id: I7d0d8e2a20d15cbed30e98cf4468e9fb5dd0f1ad
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: https://review.coreboot.org/19292
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
SeaBIOS 1.10.2 was released on February 28th, 2017 [1][2] with the
changes below.
```
$ git log --oneline rel-1.10.1..rel-1.10.2
5f4c7b1 QEMU fw_cfg: Write fw_cfg back on S3 resume
c45ca70 QEMU fw_cfg: Add functions for accessing files by key
31b6229 QEMU fw_cfg: Add command to write back address of file
aa7219d romfile-loader: Switch to using named structs
2a1d88c QEMU DMA: Add DMA write capability
d2ac564 ps2port: Disable keyboard/mouse prior to resetting ps2 controller
b0e3c67 vgasrc: Increase debug level
ca3ab93 ahci: Set upper 32-bit registers to zero
```
This fixes the problem on a Lenovo X60, that the keyboard is not
initialized by SeaBIOS when for example loaded from GRUB.
[1] https://www.seabios.org/Releases#SeaBIOS_1.10.2
Change-Id: Idc078ffa896b2e105faabd2d8befeaf9a2a0b6ac
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: https://review.coreboot.org/19290
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
The HDA verb for falco/wolf's internal mic was wrong, preventing the mic
from working properly in Windows and macOS (the Linux driver overrides
the verb table, so wasn't affected). Set the verb connector/jack bits
properly, to no connector / no jack detect, in order to fix.
Also, make (2) small non-functional fixes:
On falco, NID 0x1A was being disabled twice (instead of 0x1A and 0x1B
both being disabled - copy/paste error).
On wolf, NID 0x19 was set to an internal analog mic, where it should have
been disabled (again, copy/paste error).
Both these errors were introduced when consolidating/upstreaming
and were not present in the original Chromium sources.
Test: boot Windows [8/8.1/10] and verify mic functional with Realtek
drivers on both falco and wolf.
Change-Id: I9c343dda4762f0b1f814318c155e22c59d2da8db
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/19262
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Do not map LPC ROM into the system memory space when SPI Flash
is configured instead of an LPC ROM.
This resolves a long-standing hard boot hang issue on the ASUS
KGPE-D16 and related systems; in a nutshell, the incorrectly
mapped LPC ROM overrode low memory required by ramstage, causing
decompressed ramstage layout-dependent vectoring to romstage code
and subsequent execution of random sections of romstage. Sometimes
these random sections of romstage reconfigured the hardware in such
a way that it could not access SPI Flash on the next boot attempt.
Change-Id: I115e5d834f0ca99c2d9dbb5b9b5badbea1d98574
Signed-off-by: Timothy Pearson <tpearson@raptorengineering.com>
Reviewed-on: https://review.coreboot.org/19280
Tested-by: build bot (Jenkins)
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Daniel Kulesz <daniel.ina1@googlemail.com>
|
|
The x4x northbridge can be paired with either an ICH7 (in the case of
g41) or an ICH10 (all other cases: g45, q45, p45, ...). Only ICH10
sometimes occurs with a descriptor, gbe and an ME region.
ICH7 is always descriptorless so it makes no sense to fix CBFS to
accommodate for those other objects.
Change-Id: I4a01dfdbce1807e44932a3ac812110382332abd8
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/19181
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Reuses ICH10R functions.
TESTED on Intel DG43GT (Not supported by coreboot)
Change-Id: If9ae8ba8b95e3a7bf6596ae639eb8cafab583298
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/19232
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Remove the 'probed' setting from the Realtek 5663 headset codec I2C
device. This was added when we had a hardware issue that was preventing
I2C operation because the clock/data lines were swapped.
With new and/or reworked hardware this is no longer a problem and we do
not want the I2C layer in the kernel to talk to the device before the
rt5663 driver.
BUG=b:35585307
BRANCH=none
TEST=Boot on Eve and verify rt5663 driver still loads properly.
Change-Id: Ice38889e8f5d3fd1307056cab10fbe3f4e197749
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/19304
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Change-Id: Ie046fd3c413585131669193a6669358adf709028
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/19268
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
HEAP management is identical enough to move heap away from
first 1MiB for all platforms.
Change-Id: I4128fc084fe072fef6194d260c05592582b7b0d0
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/19267
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
- remove old, buggy NGI code from falco/peppy variants
- remove superfluous INTEL_DP/INTEL_DDI configs, since already
selected by northbridge/haswell
- always use libgfxinit when use native init config selected
- enable NGI/libgfxinit for all slippy variants
The reset of the old Haswell NGI code will be cleaned up in
a subsequent patchset.
Test: select MAINBOARD_DO_NATIVE_VGA_INIT, observe panel init
using SeaBIOS and Tianocore payloads on peppy, wolf variants
Change-Id: Id5727cad7f714ffa57e77e2a25505e3c28f55237
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/18824
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
blobtool uses the same sort of update mechanism for the .l & .y files,
so update the SCONFIG_GENPARSER Kconfig question to encompass both
utilities.
- Change the name to UTIL_GENPARSER, and update the help text.
- Update sconfig's makefile.
- Add the check to blobtool's makefile.
- Update the makefiles to check for y, not defined.
Change-Id: I6215791c9a019bce37d4a150b65d1fdbb9073156
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/19229
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Add a Makefile.inc, based on sconfig's, to use the _shipped variants
so that the build doesn't have to generate them with flex & bison.
The GENPARSER check is inactive, and will be updated in the next
commit.
Add the c_shipped & h_shipped files for the current .l & .y files.
Change-Id: Ia6c68bfb6e0611ceb6bc76cc66e43266bafc98ad
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/19228
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Use linker instead of '#include *.c'.
The smbus_fixup() was changed not to use a structure that's defined by a
northbridge since multiple different northbridges can be used. Instead
the caller now directly passed the memory slot details.
Change-Id: Ia369ece6365accbc531736fc463c713bbc134807
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Reviewed-on: https://review.coreboot.org/19082
Tested-by: build bot (Jenkins)
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Includes the DRAM controller device that knows which where the division
between addresses routed to the main memory and to the PCI bus is.
Change-Id: Id4cfeb8ff32de37723eee68a61c576e657dad30b
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Reviewed-on: https://review.coreboot.org/18896
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
This is the actual PCI Id of the internal graphics.
Change-Id: I2a25ed35a5b01de6da905619fa9fce96738d1c0e
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Reviewed-on: https://review.coreboot.org/18895
Tested-by: build bot (Jenkins)
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Without them the BS_DEV_RESOURCES stage won't traverse the bridge and
the graphics controller would be left without resources assigned.
Even worse, the resources would stay based in offset 0 which confuses
the MTRR setting code and causes a good chunk of the DRAM to be set
to type write combining.
With the patch applied, the resources are set:
Show resources in subtree (Root Device)...After assigning values.
...
PCI: 00:01.0 child on link 0 PCI: 01:00.0
+ PCI: 00:01.0 resource base ffff size 0 align 0 gran 0 limit ffff flags 60080100 index 0
+ PCI: 00:01.0 resource base f8000000 size 4000000 align 26 gran 0 limit fbffffff flags 60081200 index 1
+ PCI: 00:01.0 resource base fc000000 size 1010000 align 24 gran 0 limit fd00ffff flags 60080200 index 2
PCI: 01:00.0
- PCI: 01:00.0 resource base 0 size 4000000 align 26 gran 26 limit ffffffff flags 1200 index 10
- PCI: 01:00.0 resource base 0 size 1000000 align 24 gran 24 limit ffffffff flags 200 index 14
- PCI: 01:00.0 resource base 0 size 10000 align 16 gran 16 limit ffffffff flags 2200 index 30
+ PCI: 01:00.0 resource base f8000000 size 4000000 align 26 gran 26 limit fbffffff flags 60001200 index 10
+ PCI: 01:00.0 resource base fc000000 size 1000000 align 24 gran 24 limit fcffffff flags 60000200 index 14
+ PCI: 01:00.0 resource base fd000000 size 10000 align 16 gran 16 limit fd00ffff flags 60002200 index 30
And the caching mode is set properly:
MTRR: Physical address space:
-0x0000000000000000 - 0x0000000004000000 size 0x04000000 type 1
-0x0000000004000000 - 0x000000000e000000 size 0x0a000000 type 6
-0x000000000e000000 - 0x0000000100000000 size 0xf2000000 type 0
+0x0000000000000000 - 0x00000000000a0000 size 0x000a0000 type 6
+0x00000000000a0000 - 0x00000000000c0000 size 0x00020000 type 0
+0x00000000000c0000 - 0x000000000e000000 size 0x0df40000 type 6
+0x000000000e000000 - 0x00000000f8000000 size 0xea000000 type 0
+0x00000000f8000000 - 0x00000000fc000000 size 0x04000000 type 1
+0x00000000fc000000 - 0x0000000100000000 size 0x04000000 type 0
The problem was also spot and discussed here:
http://coreboot.coreboot.narkive.com/E9eGauzH/via-c7-on-bcom-winnet-p680-l1-l2-cache-very-slow
Change-Id: Idb4979b206838dd6455b2a16de14dc74f83af921
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Reviewed-on: https://review.coreboot.org/18894
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Otherwise, it locks up quickly. Not sure which ones are actually needed
and why, couldn't bisect it into removing even a single one.
The factory BIOS on a Neoware G170 does 200 0xed reads between setting
the registers too.
Change-Id: I6aa38768d84dd42c9c720c917a99e6b4b1e03427
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Reviewed-on: https://review.coreboot.org/18893
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Enable SERIRQ in quiet or continuous mode based on Kconfig.
Defaults to quite mode.
Change-Id: Ib40a84719fcc3a5d6b3000c3c0412f1bcf629609
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/19234
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Clean up hudson PM register accesses with some register defines.
Change-Id: I5ccf27a2463350baec53b7c79fe0fd4ec6c31306
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/19233
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
On some architectures (like AArch64), /dev/mem mappings outside of the
area marked as normal RAM use a memory type that does not support
unaligned accesses. The libc memcpy() implementation on these
architectures may not know or expect that and make an unaligned access
for certain source/dest/length alignments. Add a custom memcpy()
implementation that takes these restrictions into account and use it
anywhere we copy straight out of /dev/mem memory.
Change-Id: I03eece380a14a69d4be3805ed72fba640f6f7d9c
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/18300
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Update from commit 124af94f - Fri Feb 26, 2016
(skylake boards: unconditionally re-enable 8254 PIT for legacy)
To commit eb583fa8 - Wed Mar 29, 2017
(rk3399_sdhci: Reintroduce PHY power-cycling at 52MHz)
This brings the stable version of depthcharge forward by 325 commits.
Change-Id: I31b3235df6d36409ff1b365e6adb6852281df097
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/19220
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Update from commit 2afd66eb - Fri Jul 29, 2016
([pixbuf] Enable PNG format by default)
To commit fd6d1f46 - Fri Mar 31, 2017
([thunderx] Use ThunderxConfigProtocol to obtain board configuration)
This moves the stable iPXE commit forward 144 commits.
Change-Id: Ia0c97f863be39632c9206ca95b3857047fc37e26
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/19221
Tested-by: build bot (Jenkins)
Reviewed-by: Philippe Mathieu-Daudé <philippe.mathieu.daude@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Timothy Pearson <tpearson@raptorengineering.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Vendor BIOS leaves UPMC1 untouched (on 945gc the default is 0x0203).
Not running PCIEx16 init which is valid for 945gm seems to fix all
issues and instabilities related to the PEG port.
According to lspci the link width is at the desired x16.
It is unknown if devices requesting a lower width work automatically
or need more configuration.
What happens is that IGD gets disabled by the disable function in
gma.c when an external GPU is found unless
CONFIG_ONBOARD_VGA_IS_PRIMARY is set.
Setting IGD as secondary makes Linux (4.10) hang, so this behavior is
a requirement for now.
TESTED on P5GC-MX with a discrete GPU and both
CONFIG_ONBOARD_VGA_IS_PRIMARY set and unset.
Change-Id: I6da8aa7714073f4b34df5ae3c1eb4c19e27ddc97
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/18549
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Remove the ACPI ALS device from the EC configuration because this system
has an ALS that is presented through the new EC sensor interface rather
than the legacy ACPI interface.
BUG=b:37179776
BRANCH=none
TEST=Boot an Eve device and ensure that 'acpi-als' device is not present
in /sys/bus/iio/devices.
Change-Id: Ie18b8a661e4d16464784ca8a227586036e7631de
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/19265
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Set UART0 to "PchSerialIoSkipInit" so the pins for this device are not
set back to native mode by FSP when configured as GPIO input by coreboot.
Now that FSP is not touching the pins I also removed the workaround to
reconfigure the pins after FSP.
BUG=b:35647877
BRANCH=none
TEST=Verify that GPP_C8-GPP_C11 are configured as GPIO input once the OS
is booted and they are not set back to native function by FSP.
Change-Id: Ifec4fa3e66ceeb660bad00c66bc7bd44bb457a01
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/19264
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
These lines act as inputs to both EC and AP and when the corresponding
TCPC mux is in low power mode the line is floating. Add an internal
pull-down to each GPIO to prevent it from floating in this state.
BUG=b:35775012
BRANCH=none
TEST=Verify that the kernel does not see a device present on DP when
the TCPC mux is in low power mode.
Change-Id: Ie229f84871e9994467c0ab660cc7e271a51d9cbb
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/19263
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
With recent change to use common block PCR (ccd8700c),
IOSF_BASE_ADDRESS was renamed to PCR_BASE_ADDRESS. However, SD card
change (99ce8a9b) was not rebased on top of it, so IOSF_BASE_ADDRESS
slipped into the tree. Fix this by replacing all occurrences of
IOSF_BASE_ADDRESS by PCR_BASE_ADDRESS.
Change-Id: I40eb07be306035c940fc960896e0807d6c73bafa
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/19277
Tested-by: build bot (Jenkins)
Reviewed-by: Venkateswarlu V Vinjamuri <venkateswarlu.v.vinjamuri@intel.com>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
With EuP and PME enabled the USB power turns off during S5.
Change-Id: I8b9fd7bb308f544401f90f8aa5ffaec61251b2b3
Signed-off-by: Nicola Corna <nicola@corna.info>
Reviewed-on: https://review.coreboot.org/19073
Tested-by: build bot (Jenkins)
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
This configures GPIO_177 as native function.
This enables OS to boot from sdcard.
BUG=b:35648535
TEST=Check OS boot from sdcard.
Change-Id: I73901d4a1b39752cbc452f3286d494587dac95d4
Signed-off-by: Venkateswarlu Vinjamuri <venkateswarlu.v.vinjamuri@intel.com>
Reviewed-on: https://review.coreboot.org/18948
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Vaibhav Shankar <vaibhav.shankar@intel.com>
|
