| Age | Commit message (Collapse) | Author |
|---|
|
This changes the number of chip selects that we configure from 2 to 1.
On current setups with (x16 memory 4Gbit chips) that means that we're
at 2GByte.
Technically we should add a second setting in the ares_ddr3_timings
and select between the two of the based on board strappings. That
would make the CONFIG_RUN_TIME_BANK_NUMBER work properly. I've
changed the ddr3_mem_ctrl_init() so it should handle that, but I'm not
actually doing the board strapping read right now.
This change means that accesses to 0xA0000000 - 0xFFFFFFFF on 2G
systems will no longer put the system in a messed up state (leading to
a hang). It also prevents some of the weird boot behavior that we've
seen that comes and goes depending on U-Boot alignment. See
<http://crosbug.com/p/20577>.
This patch was ported from: https://gerrit.chromium.org/gerrit/66117
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Change-Id: Ib4cfe420aac30bd817438f06d01e8671afc4a27d
Reviewed-on: https://chromium-review.googlesource.com/167210
Commit-Queue: David Hendricks <dhendrix@chromium.org>
Tested-by: David Hendricks <dhendrix@chromium.org>
Reviewed-by: ron minnich <rminnich@chromium.org>
(cherry picked from commit 0ea574243058068702e3f6bc7355098745d16880)
Signed-off-by: Isaac Christensen <isaac.christensen@se-eng.com>
Reviewed-on: http://review.coreboot.org/6612
Tested-by: build bot (Jenkins)
|
|
Change-Id: I8f672b872862d3448ccd2cf28fd3c05b0108ff8b
Found-by: Coverity Scan
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/6561
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Fine tuning DDR timings value for better stability
* Changed Data Driver Strength from 34 ohms to 30 ohms, expected to
enhance signal integrity.
* Changed DQ signal from 0xf to 0x1f000f, to keep default value safe.
* Changed mrs[2] and added new mrs direct command for setting WL/RL
without resetting DLL.
* Added explicit reset value write in phy_con0 instead of just setting
a bit, to ensure that reset happens.
* Added DREX automatic control for ctrl_pd in none read memory state.
This is ported from: https://gerrit.chromium.org/gerrit/61405
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Change-Id: I59e96e6dede7b49c6572548aca664d82ad110bb1
Reviewed-on: https://chromium-review.googlesource.com/66995
Reviewed-by: ron minnich <rminnich@chromium.org>
Commit-Queue: David Hendricks <dhendrix@chromium.org>
Tested-by: David Hendricks <dhendrix@chromium.org>
(cherry picked from commit ec34b711c6d270672c56d45c370ca14c0aa27ca3)
Signed-off-by: Isaac Christensen <isaac.christensen@se-eng.com>
Reviewed-on: http://review.coreboot.org/6611
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
The EHCI host controllers in Samsung Exynos SoC seem to be a little more
picky than Intel ones. When they reach the dummy_qh in the periodic
frame list, they try to access the next qTD pointer even though it's
NULL, and run into a HostSystemError. This patch explicitly sets the
Terminate bit on those pointers to mark them invalid.
Change-Id: I50fa79bbf1c5fab306d7885c01efd66b13e279b8
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/66884
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
(cherry picked from commit c575a5c958ce88732d28044352c89418bcd5ea86)
Signed-off-by: Isaac Christensen <isaac.christensen@se-eng.com>
Reviewed-on: http://review.coreboot.org/6608
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
This patch intends to remove all code which enables hardware read
leveling. We need to disable h/w read leveling because new ASV table
is merged in kernel (which is based on the new characterization
condition) and new characterization environment has h/w read leveling
disabled, so we should also disable this. Also, disabling h/w read
leveling improves the MIF LVcc value (LVcc value is the value at which
DDR will fail to work properly), improve LVcc means we have enough
voltage margin for MIF. When h/w leveling is enabled, we have almost
zero volatge margin.
This was ported from: https://gerrit.chromium.org/gerrit/66070
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Change-Id: Id0a2d77e6214325f226d51ae08464b39424cea83
Reviewed-on: https://chromium-review.googlesource.com/66994
Reviewed-by: Gabe Black <gabeblack@chromium.org>
Commit-Queue: David Hendricks <dhendrix@chromium.org>
Tested-by: David Hendricks <dhendrix@chromium.org>
(cherry picked from commit d29add98f52876aaed4fee2b76edf6b4591e66e8)
Signed-off-by: Isaac Christensen <isaac.christensen@se-eng.com>
Reviewed-on: http://review.coreboot.org/6610
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
This patch moves around some of the existing Exynos5 USB 2.0 PHY code
to make it cleaner in preparation of the 3.0 PHYs. It moves the VBUS
GPIOs (which are completely board-specific) into the mainboard code and
makes sure to only initialize PHYs on the boards that actually need
them. It also removes the USB 3.0 PLL hack that was needed on Snow from
the Pit and Kirby boards (which do not have that PLL anymore).
Change-Id: Ia35f47a765acff60481f0907f7448ec4f78e0937
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/66887
Reviewed-by: Stefan Reinauer <reinauer@google.com>
(cherry picked from commit c3b1a8b687b535f4d5ac1b3bd2a4760151698fdb)
Signed-off-by: Isaac Christensen <isaac.christensen@se-eng.com>
Reviewed-on: http://review.coreboot.org/6609
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
The USB bulk and control transfer functions in libpayload currently
always return 0 for success and 1 for all errors. This is sufficient for
current use cases (essentially just mass storage), but other classes
(like certain Ethernet adapters) need to be able to tell if a transfer
reached the intended amount of bytes, or if it fell short.
This patch slightly changes that USB API to return -1 on errors, and the
amount of transferred bytes on successes. All drivers in the current
libpayload mainline are modified to conform to the new error detection
model. Any third party users of this API will need to adapt their
if (...<controller>->bulk/control(...)) checks to
if (...<controller>->bulk/control(...) < 0) as well.
The host controller drivers for OHCI and EHCI correctly implement the
new behavior. UHCI and the XHCI stub just comply with the new API by
returning 0 or -1, but do not actually count the returned bytes.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/48308
Reviewed-by: Gabe Black <gabeblack@chromium.org>
Reviewed-by: Stefan Reinauer <reinauer@google.com>
Tested-by: Gabe Black <gabeblack@chromium.org>
Commit-Queue: Gabe Black <gabeblack@chromium.org>
Updated the patch to support XHCI as well.
Change-Id: Ic2ea2810c5edb992cbe185bc9711d2f8f557cae6
(cherry picked from commit e39e2d84762a3804653d950a228ed2269c651458)
Signed-off-by: Isaac Christensen <isaac.christensen@se-eng.com>
Reviewed-on: http://review.coreboot.org/6390
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
The old ddr3_mem_ctrl_init() for exynos5420 had hardcoded constants
for accessing directcmd registers. Modify to use #defines where
possible.
This is ported from: https://gerrit.chromium.org/gerrit/#/c/65616
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Change-Id: I01567fc6941608a570832de97259c55e84942d01
Reviewed-on: https://gerrit.chromium.org/gerrit/66789
Commit-Queue: David Hendricks <dhendrix@chromium.org>
Tested-by: David Hendricks <dhendrix@chromium.org>
Reviewed-by: Ronald G. Minnich <rminnich@chromium.org>
(cherry picked from commit d751e019f450172f060ce255ae53e972bc4a19ea)
Signed-off-by: Isaac Christensen <isaac.christensen@se-eng.com>
Reviewed-on: http://review.coreboot.org/6605
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
|
|
As per hardware recommendation, CKE PAD retention release must
happen just before gate leveling enable and only in case of resume.
Hence, this patch moves pad retention release from dmc_common.c to
dmc_init_ddr3_exynos5420.c. In addition to this we are providing
125 (+3 extra being safe) times auto refresh to DRAM by sending
REFA direct command. This is required because when CKE PAD retention
release happens, self refresh mode of DDR3 is disabled.
Hence, auto refresh 125 times.
This is ported from https://gerrit.chromium.org/gerrit/#/c/65573
Note: Since WAKEUP_DIRECT does not go thru memory init, it should be
safe to move CKE PAD retention out of bootblock.c.
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Change-Id: Idec5d6fbbe3c6344d47401ba7203079c52a9b866
Reviewed-on: https://gerrit.chromium.org/gerrit/66788
Commit-Queue: David Hendricks <dhendrix@chromium.org>
Tested-by: David Hendricks <dhendrix@chromium.org>
Reviewed-by: Ronald G. Minnich <rminnich@chromium.org>
(cherry picked from commit 96cbcb09245d4df92d3e1998704ab440be42df25)
Signed-off-by: Isaac Christensen <isaac.christensen@se-eng.com>
Reviewed-on: http://review.coreboot.org/6604
Tested-by: build bot (Jenkins)
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
|
|
Apparently the IROM doesn't like data caches... the recently added
dcache-in-bootblock makes A-A booting fail, and flushes/invalidations
alone don't seem to fix it. It's pretty fast anyway, so we just disable
the cache again for the duration of the IROM call.
Also removes a superfluous invalidation line from the bootblock code...
dcache_mmu_enable/disable already take care of that.
Old-Change-Id: I35580d15664c7b4197d4ed14028720147adbf918
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/66602
Reviewed-by: Gabe Black <gabeblack@chromium.org>
Reviewed-by: David Hendricks <dhendrix@chromium.org>
(cherry picked from commit e9c28a6a7a88c8286e62764ee5ad2694da2e822f)
exynos5: Implement booting from SDMMC media
This patch augments the alternative CBFS media source implementation for
Exynos5250 and Exynos5420 to allow booting from SDMMC devices (such as
an SD or uSD card reader, if available). It also moves MMC
initialization for the Snow, Pit and Kirby boards from romstage to
ramstage (mainboard_init) to prevent it from interfering with the IROM
during SDMMC boot.
Old-Change-Id: Ic4adef80c28262d084a53c28ec59aa7ac3af50c8
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/66154
(cherry picked from commit 08de13b72432c076e3327c048df93d89d52b0ecc)
snow and pit: turn on FET4 (for SD card) at bootup
Explictly enable FET4 on Snow and Pit.
Historically we haven't needed to do this because:
* On snow there's a bypass around FET4 which effectively eliminates
it. Even if we don't turn on FET4 the SD card is still powered.
Turning on FET4 doesn't hurt though and is technically correct.
* On pit the EC turns on FET4 on cold bootup.
On pit we run into a problem if the kernel turns off FET4 like in
<https://gerrit.chromium.org/gerrit/#/c/65332/> and then we get a
software reset or warm reset. In this case the EC won't know to turn
it back on.
This was ported from: https://gerrit.chromium.org/gerrit/#/c/65673
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Old-Change-Id: I57337f12b38889e6afee8577cf8807ec4c41e91c
Reviewed-on: https://gerrit.chromium.org/gerrit/66786
Commit-Queue: David Hendricks <dhendrix@chromium.org>
Tested-by: David Hendricks <dhendrix@chromium.org>
Reviewed-by: Ronald G. Minnich <rminnich@chromium.org>
(cherry picked from commit e910117047d898b6b1d0dc965ef2ec0237d17646)
Squashed three commits for alternate cbfs SD support.
Change-Id: Idbd1fd4776cbf8cb20d03e6b691104cd8540a1ec
Signed-off-by: Isaac Christensen <isaac.christensen@se-eng.com>
Reviewed-on: http://review.coreboot.org/6530
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
It's a more direct approach to get the file size.
Change-Id: If49df26bf4996bd556c675f3a673d0003b4adf89
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/6594
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Generate the board-status repo URL by replacing the
last occurrence of "/coreboot" by "/board-status",
which works across repo URL schemes (gerrit provides
several).
Change-Id: Iccb53bde994be619c1436815e13741d63738edf7
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/6574
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
|
|
Change-Id: If7286abf91f758cfbac2c85dcad336f38f70d843
Signed-off-by: Daniele Forsi <dforsi@gmail.com>
Reviewed-on: http://review.coreboot.org/6579
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Tested-by: build bot (Jenkins)
|
|
Accept only one command line argument (the input file name); close input
stream both on error and on success; print more informative error messages
when files could not be opened.
Change-Id: Ib2f0622a332317d7a13f33f1e5787381804c43a9
Found-by: missing fclose()'s found by Cppcheck 1.65
Signed-off-by: Daniele Forsi <dforsi@gmail.com>
Reviewed-on: http://review.coreboot.org/6573
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Fix whitespace.
Change-Id: I9e28b819d685851a84cee6c5a71458e07d0ec808
Signed-off-by: Daniele Forsi <dforsi@gmail.com>
Reviewed-on: http://review.coreboot.org/6577
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Clean up as requested in commit e6df041b.
No functional changes.
Change-Id: Iec3f7ee25fd8351c7e13d660e2df6461f7745478
Signed-off-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-on: http://review.coreboot.org/6597
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Clean up a coding style violation as requested in the review of
commit 09670265.
Change-Id: I2815635efbb70a1e5841ca79cf2b4845bc6c23f2
Signed-off-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-on: http://review.coreboot.org/6598
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Change-Id: Ia66c71c3adf2ae0d413750b5e59e3eaba3888a0b
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/6587
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
|
|
The absf files contain the modifications to the default settings in
the FSP. They are used as input files for Intel's 'Binary Configuration
Tool' (BCT) along with the FSP.bin file to generate customized FSP
binaries.
The Minnow Max absf files set up the values for the soldered down
memory. This requirement will go away with the release of the next
Bay Trail FSP, and the memory settings will be configurable at
runtime.
Change-Id: Id72545d78a7e82d9a5090710a9c7a8a9b1e81208
Signed-off-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-on: http://review.coreboot.org/6432
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
|
|
The Bakersport board is a variant of the Bayley Bay mainboard that uses
one ECC DIMM instead of two non-ECC dimms.
This commit uses the Bayley Bay mainboard directory and modifies the
required pieces to add the Bakersport board variant. It disables the
second DIMM, points to an ECC version of the FSP, and sets the board
name to be Bakersport instead of Bayley Bay.
All of the code is still contained in the bayleybay_fsp directory. It
seems like duplicating the whole directory for the one line of code
that's actually different between the two platforms.
Change-Id: Ia31e9ee927a6810a01a1ae143fcb00cfb7d8a7aa
Signed-off-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-on: http://review.coreboot.org/5983
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
|
|
Still not lint-stable due to too many open issues, but
at least it doesn't try to touch files that aren't part
of the repository anymore.
Change-Id: I654b15480094c7731a7d0d17fa1622a0b41ac34a
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/6584
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
|
|
The whitespace test only trips on files that are part
of the git index - in particular not temporary editor
files or other cruft that doesn't hurt anyone.
Change-Id: I793fcc773845ee02281d8614b07e9c5958126a5a
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/6582
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
|
|
Change-Id: I23a088919aaac16066e5dd8300a081a8095a93f0
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/6589
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
MinnowMax board using Intel's Bay Trail FSP
Working:
- Booting from SATA / USB / (USB3 with latest SeaBIOS)
Not working:
- Boot from SD
- S3 Suspend / Resume
***** To configure the FSP *****
Download the Bay Trail FSP and the binary config tool:
Modify the standard Bay Trail FSP:
run the bct tool with the command line options:
bct --bin <Bay Trail FSP Binary> \
--absf src/vendorcode/intel/fsp/baytrail/absf/minnowmax_Xgb.absf \
--bout <path to save the updated FSP to>
Here are the required changes for modifying the FSP manually:
Enable Memory Down: Enabled
DRAM Speed: 1066 MHz
DIMM_DWidth: x16
DIMM_Density: 4 Gbit (2GB Minnow Max) / 2 Gbit (1GB Minnow Max)
tCL: 7
tRP_tRCD: 7
tWR: 8
tRRD: 6
tRTP: 4
tFAW: 27
Other FSP values can remain the same.
***** To configure the vbios *****
The vbios is in the Bay Trail FSP package.
Download Intel's "Binary Modification Program" (BMP)
Use it to disable all ports except HDMI on port B.
Change-Id: I00d90e0d838d70c9d25c69f5115d0c9d6d19855c
Signed-off-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-on: http://review.coreboot.org/6429
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
|
|
The current XHCI code only sets IOC on the last TRB of a TD, and
doesn't set ISP anywhere. On my Synopsys DesignWare3 controller, this
won't generate an event at all when we have a short transfer that is not
on the last TRB of a TD, resulting in event ring desync and everyone
having a bad time. However, just setting ISP on other TRBs doesn't
really make for a nice solution: we then need to do ugly special casing
to fish out the spurious second transfer event you get for short
packets, and we still need a way to figure out how many bytes were
transferred. Since the Short Packet transfer event only reports
untransferred bytes for the current TRB, we would have to manually walk
the rest of the unprocessed TRB chain and add up the bytes. Check out
U-Boot and the Linux kernel to see how complicated this looks in
practice.
Now what if we had a way to just tell the HC "I want an event at exactly
*this* point in the TD, I want it to have the right completion code for
the whole TD, and to contain the exact number of bytes written"? Enter
the Event Data TRB: this little gizmo really does pretty much exactly
what any sane XHCI driver would want, and I have no idea why it isn't
used more often. It solves both the short packet event generation and
counting the transferred bytes without requiring any special magic in
software.
Change-Id: Idab412d61edf30655ec69c80066bfffd80290403
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/170980
Reviewed-by: Stefan Reinauer <reinauer@google.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
(cherry picked from commit e512c8bcaa5b8e05cae3b9d04cd4947298de999d)
Signed-off-by: Isaac Christensen <isaac.christensen@se-eng.com>
Reviewed-on: http://review.coreboot.org/6516
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
The case doesn't look like a deliberate fall-through,
since the next case (SNB/IVB/HSW) is more specific
than the one before it, so break out.
Change-Id: I55497aefe9e835842a82121270f2b2a9952f560d
Found-by: Coverity Scan
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/6571
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Remove some dead coded spotted in Clang builds.
Change-Id: Ia23e16eae76593eee249e0894ef1d704a274616f
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/6130
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@google.com>
|
|
Provide functionality to create dynamic classes based on program name and
architecture for which the program needs to be compiled/linked. define_class
takes program_name and arch as its arguments and adds the program_name to
classes-y to create dynamic class. Also, compiler toolset is created for the
specified arch. All the files for this program can then be added to
program_name-y += .. Ensure that define_class is called before any files are
added to the class. Check subdirs-y for order of directory inclusion.
One such example of dynamic class is rmodules. Multiple rmodules can be used
which need to be compiled for different architectures. With dynamic classes,
this is possible.
Change-Id: Ie143ed6f79ced5f58c200394cff89b006bc9b342
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: http://review.coreboot.org/6426
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Change-Id: I999818833c9040eb4f4e19c313b5e9be216ffd86
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/6585
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
In the error case, they survived.
Change-Id: I15167be12ff9ee03f1b3bb86b93f20cb5be02b10
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/6583
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
|
|
[ $3 -eq 1 ] fails if no third argument is given.
[ "$3" -eq 1 ] still fails.
Doing a string comparison is robust across shells.
Change-Id: I3ee388fdbe51b7ab9344d86e67827654714d3191
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/6576
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
irq_helper.h intentionally gets included into irqroute.asl twice - once
for pic mode and once for apic mode. Since people are used to seeing
guard statements on the .h files, add the guards to irqroute.h and add
a comment to irq_helper.h explaining why they aren't there. Add a
time.
Change-Id: I882cbbff0f73bdb170bd0f1053767893722dc60a
Signed-off-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-on: http://review.coreboot.org/6572
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
|
|
Change-Id: I16aa154ae0b6f21d5e160a950d39013820d7503c
Signed-off-by: Daniele Forsi <dforsi@gmail.com>
Reviewed-on: http://review.coreboot.org/6578
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
|
|
Change-Id: I76ae5e294c157e73d07fd30cdb1c191d78efd5eb
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/6581
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
|
|
Change-Id: I2eba1ca27c1f8181a9c6288f6794922915575790
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/6586
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
It's not really used.
Change-Id: I760d5a4cbe46d17ef37ea34e29eecdb0721cb945
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/6588
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
This new version is used to implement the version which doesn't take the
input and output buffer sizes.
Old-Change-Id: I8935024aca0849bc939263d7fc3036c586e63c68
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/65510
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Stefan Reinauer <reinauer@google.com>
Tested-by: Gabe Black <gabeblack@chromium.org>
Commit-Queue: Gabe Black <gabeblack@chromium.org>
(cherry picked from commit 465d167ad2f6a67d0b2c91fb6c68c8f9a09dd395)
libpayload: Make lzma truncation non-fatal.
If the size the lzma header claims it needs is bigger than the space we have,
print a message and continue rather than erroring out. Apparently the encoder
is lazy sometimes and just puts a large value there regardless of what the
actual size is.
This was the original intention for this code, but an outdated version of the
patch ended up being submitted.
Old-Change-Id: Ibcf7ac0fd4b65ce85377421a4ee67b82d92d29d3
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/66235
Reviewed-by: Stefan Reinauer <reinauer@google.com>
Commit-Queue: Gabe Black <gabeblack@chromium.org>
Tested-by: Gabe Black <gabeblack@chromium.org>
(cherry picked from commit 30c628eeada274fc8b94f8f69f9df4f33cbfc773)
Squashed two related commits and updated the commit message to be
more clear.
Change-Id: I484b5c1e3809781033d146609a35a9e5e666c8ed
Signed-off-by: Isaac Christensen <isaac.christensen@se-eng.com>
Reviewed-on: http://review.coreboot.org/6408
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
The CBFS core checks the result of a media->map() operation in multiple
places for CBFS_MEDIA_INVALID_MAP_ADDRESS, suggesting that this is a
valid response. However, it ironically fails to do so when actually
mapping the CBFS file itself, which can fail on buffer-constrained
systems since the size is much larger than when mapping metadata. This
patch adds a check with an error message and a NULL pointer return for
that case to make it easier to understand this condition.
Change-Id: Icae3dd20d3d111cdfc4f2dc6397b52174349b140
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/174951
Reviewed-by: Gabe Black <gabeblack@chromium.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
(cherry picked from commit 63f2c4465f9633a637186e69bc3862d5413106ac)
Signed-off-by: Isaac Christensen <isaac.christensen@se-eng.com>
Reviewed-on: http://review.coreboot.org/6537
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
On x86 VbExGetTimer() uses rdtsc. However, on all
other platforms, let's just use coreboot's monotonic timers.
Change-Id: I0cd359f298be33776740305b111624147e2c850d
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: https://chromium-review.googlesource.com/169620
(cherry picked from commit e910bb17522d5de42c0fc3cc945278e733fa2553)
Signed-off-by: Isaac Christensen <isaac.christensen@se-eng.com>
Reviewed-on: http://review.coreboot.org/6534
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
On ARM platforms the TPM is not attached through LPC but through I2C.
This patch adds an I2C TPM driver that supports the following chips:
* Infineon SLB9635
* Infineon SLB9645
In order to select the correct TPM implementation cleanly, CONFIG_TPM
is moved to src/Kconfig and does the correct choice.
Old-Change-Id: I2def0e0f86a869d6fcf56fc4ccab0bc935de2bf1
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: https://chromium-review.googlesource.com/167543
Reviewed-by: ron minnich <rminnich@chromium.org>
(cherry picked from commit b4049a0e96f6335a93877e1e884f9a440487c421)
i2c tpm: Remove mostly useless delay code/tables.
I assume from the code in the TPM driver that the TPM spec defines
different types of delays and timeouts which each have a particular
duration, and that the TPM can tell you how long each type is if you ask
it. There was a large table, some members of a data structure, and a
function or two which managed the timeouts and figured their value for
different operations. The timeout values for the various "ordinals"
were never set in the vendor specific data structure, however, and
always defaulted to 2 minutes. Similarly the timeouts a, b, c, and d
were never overridden from their defaults. This change gets rid of all
the timeout management code and makes the "ordinal" timeout 2 minutes
and the a, b, c, and d timeouts 2 seconds, the larger of the two default
values.
This is a port from depthcharge to coreboot, original change:
https://chromium-review.googlesource.com/#/c/168363/
Signed-off-by: Gabe Black <gabeblack@google.com>
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Old-Change-Id: I79696d6329184ca07f6a1be4f6ca85e1655a7aaf
Reviewed-on: https://chromium-review.googlesource.com/168583
Reviewed-by: Gabe Black <gabeblack@chromium.org>
Tested-by: Stefan Reinauer <reinauer@google.com>
Commit-Queue: Stefan Reinauer <reinauer@google.com>
(cherry picked from commit b22395a73f361c38626911808332a3706b2334fe)
TPM: Stop requesting/releasing the TPM locality.
The locality is requested when the TPM is initialized and released when
it's cleaned up. There's no reason to set it to the same thing again and
restore it back to the same value before and after every transaction.
forward ported from https://chromium-review.googlesource.com/#/c/168400
Old-Change-Id: I291d1f86f220ef0eff6809c6cb00459bf95aa5e0
Signed-off-by: Gabe Black <gabeblack@google.com>
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: https://chromium-review.googlesource.com/168584
Reviewed-by: Gabe Black <gabeblack@chromium.org>
(cherry picked from commit cc866c20c6f936f349d2f1773dd492dca9bbf0c1)
Squashed three commits for the i2c tpm driver.
Change-Id: Ie7a50c50fda8ee986c02de7fe27551666998229d
Signed-off-by: Isaac Christensen <isaac.christensen@se-eng.com>
Reviewed-on: http://review.coreboot.org/6519
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
A bootblock overwalk was occuring when deriving the actual
length, the bootblock size was not taken into account and bootblock
size was not aligned.
Resolved merge conflict.
Change-Id: I7eb42f8deaaf223dcf07b37bb7dde4643acd508f
Signed-off-by: Steven Sherk <steven.sherk@se-eng.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/65989
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Commit-Queue: Steve Sherk <ssherk70@gmail.com>
Tested-by: Steve Sherk <ssherk70@gmail.com>
(cherry picked from commit 20b0ba479b01755fbdc7f3dd9214e8af923402ba)
Signed-off-by: Isaac Christensen <isaac.christensen@se-eng.com>
Reviewed-on: http://review.coreboot.org/6539
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
There are three coreboot table tags that all define some kind of memory
region, and each has their own homologous struct. I'm about to add a
fourth so I'll just clean this up and turn it into a generic struct
lb_range instead.
Change-Id: Id148b2737d442e0636d2c05e74efa1fdf844a0d3
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/167154
(cherry picked from commit 22d82ffa3f5500fbc1b785e343add25e61f4f194)
Signed-off-by: Isaac Christensen <isaac.christensen@se-eng.com>
Reviewed-on: http://review.coreboot.org/6456
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
The GPIO controller uses IRQ14 as an active high level triggered
source for GPIOs that are configured to trigger shared interrupt.
This was also tested on bolt by configuring the touchscreen to use
a shared GPIO interrupt:
localhost ~ $ grep atmel_mxt_ts /proc/interrupts
54: 24 188 93 124 LP-GPIO-demux atmel_mxt_ts
Change-Id: I3765120112bae11407e5b2020399d0d0b8e3cef8
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/171901
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
(cherry picked from commit 63a0c80ce5a19410d0608fede5a9fe0ec1c8e5c1)
Signed-off-by: Isaac Christensen <isaac.christensen@se-eng.com>
Reviewed-on: http://review.coreboot.org/6541
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
This resolves WiFi issues after suspend/resume.
It needs related SPI descriptor soft strap change to
enable SLP_WLAN as a GPIO instead of owned by the ME.
Change-Id: I03f4458d1e52a913770d391061baa6cfa41e8558
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/170577
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
(cherry picked from commit cf1fe0524ad4793c8c422dc3fed3007b7fc96038)
Signed-off-by: Isaac Christensen <isaac.christensen@se-eng.com>
Reviewed-on: http://review.coreboot.org/6533
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
|
|
We were running this loop 100 times with 5 ms delays. Change it
to run 500 times with 1 ms delays, which gives us the same
overall timeout but lets us bail out a bit sooner -- in practice,
at most, 4 ms sooner but every bit counts. Note, however, that
the tighter timing does reduce opportunities for threading. There
is a non-obvious set of tradeoffs on timeouts.
Change-Id: I4af671c2a791aa92e446e66ac2fe5710d1e6aa4c
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: https://chromium-review.googlesource.com/167387
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Commit-Queue: ron minnich <rminnich@chromium.org>
Tested-by: ron minnich <rminnich@chromium.org>
(cherry picked from commit 575e910127dc74416018f182ef27ef223e61daef)
Signed-off-by: Isaac Christensen <isaac.christensen@se-eng.com>
Reviewed-on: http://review.coreboot.org/6543
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
This patch enhances the armv7 exception handlers in Coreboot and
libpayload to show the correct SP and LR registers from the aborted
context, and also dump a part of the current stack. Since we cannot
access the banked registers of SVC mode from a different exception mode,
it changes Coreboot (and its payloads) to run in System mode instead. As
both modes can execute all privileged instructions, this should not have
any noticeable effect on firmware operation (please correct me if I'm
wrong!).
Change-Id: I0e04f47619e55308f7da4a3a99c9cae6ae35cc30
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/170045
Reviewed-by: Gabe Black <gabeblack@chromium.org>
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
(cherry picked from commit d0db2f5e938200e3f5899c5e1f1606ab2dd5b334)
Signed-off-by: Isaac Christensen <isaac.christensen@se-eng.com>
Reviewed-on: http://review.coreboot.org/6538
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
While the result will not be pretty (ie. ifdtool will
mis-parse string components longer than 255 characters),
at least it doesn't overflow stack variables anymore.
Change-Id: I263c5cf823a2d8a863dcece7c4ee0b26475f9fc4
Found-by: Coverity Scan
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/6562
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Tested-by: build bot (Jenkins)
|
|
The CPU_ADDR_BITS was being unconditionally set.
Don't do that.
Change-Id: Idbc63328fade8f5f05f7f46282139b86e6694989
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/169711
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
(cherry picked from commit 858f96d28d8d0aeffe58e1d4d1d559ad161aab66)
Signed-off-by: Isaac Christensen <isaac.christensen@se-eng.com>
Reviewed-on: http://review.coreboot.org/6535
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
|
|
New SPD and update to the SPD map. Add both a 4GB and 2GB option.
4GB = RAM_ID{1,1,0}
2GB = RAM_ID{1,1,1}
Original-Change-Id: I37318c1b5a6ee84b7c55da00d326f10fe8af6f1e
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
(cherry picked from commit 7eb5a4ef1062a34e883c3f356ab0dc00ba07910d)
Change-Id: I0f35a7f5191fefeb5910a2d28aea153516d9a11d
Reviewed-on: https://chromium-review.googlesource.com/171693
Tested-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Commit-Queue: Duncan Laurie <dlaurie@chromium.org>
(cherry picked from commit b02fa777aa5935021b2c69f7345dffd111cbd118)
Signed-off-by: Isaac Christensen <isaac.christensen@se-eng.com>
Reviewed-on: http://review.coreboot.org/6545
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
This file isn't compiled into anything, and probably wouldn't since it has a
lot of baggage from it's U-Boot origins.
Change-Id: I29d87afd2a283010a653d3d48fdd3a79622e3b99
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: https://chromium-review.googlesource.com/170423
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: David Hendrix <dhendrix@chromium.org>
Commit-Queue: Gabe Black <gabeblack@chromium.org>
Tested-by: Gabe Black <gabeblack@chromium.org>
(cherry picked from commit 1146c570f0e448f7db4ec82749e91099c946a2dc)
Signed-off-by: Isaac Christensen <isaac.christensen@se-eng.com>
Reviewed-on: http://review.coreboot.org/6544
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
|
|
The source file reset.c, present in both the exynos5250 and 5420 directories,
is not being built for either SOC. Let's get rid of the clutter.
Change-Id: Iab4c7982a271d08cbaf3207b6f5431f0ef52697e
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: https://chromium-review.googlesource.com/170402
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: David Hendrix <dhendrix@chromium.org>
Commit-Queue: Gabe Black <gabeblack@chromium.org>
Tested-by: Gabe Black <gabeblack@chromium.org>
(cherry picked from commit 0ce3898276ff49d171a0d8a650806f0305c0576f)
Signed-off-by: Isaac Christensen <isaac.christensen@se-eng.com>
Reviewed-on: http://review.coreboot.org/6542
Tested-by: build bot (Jenkins)
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
|
|
gma_fui_init repeats the initializations already performed in gma_setup_panel.
These redundant initializations reset any gtt settings done before this call.
Hence, they had to be done again after call to gma_fui_init. However, the call
gma_fui_init is not required at all. Does not affect the behavior of suspend/resume.
Old-Change-Id: Idfb9f9930624694b878ddc0fe8648b3c8dd80e55
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/65997
Reviewed-by: Ronald G. Minnich <rminnich@chromium.org>
Reviewed-by: Stefan Reinauer <reinauer@google.com>
Commit-Queue: Furquan Shaikh <furquan@chromium.org>
Tested-by: Furquan Shaikh <furquan@chromium.org>
(cherry picked from commit c376aea1b89c9a829874d5c657693993a3bb1f13)
Falco/Slippy: Patch to fix garbage on screen during graphics initialization in normal mode
Depending on the init_fb parameter:
1) For normal mode, first page is filled with zeroes and setgtt is used make all GTT entries point to this
same page
2) For developer/recovery mode, we init the gtt to consecutive pages
Old-Change-Id: I281b0b7efe01f7892e98b19ff9a63c04b087bd2c
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/65633
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Commit-Queue: Furquan Shaikh <furquan@chromium.org>
Tested-by: Furquan Shaikh <furquan@chromium.org>
(cherry picked from commit 97c99dfe52ef3a87d387fdbf27ad3a28ad81c722)
Squashed two graphics related commits for Falco/Slippy.
Change-Id: I7ddb92672c026fe66f9fb0caba9d8fdc3f8a9d0a
Signed-off-by: Isaac Christensen <isaac.christensen@se-eng.com>
Reviewed-on: http://review.coreboot.org/6536
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Representing a (non-negative) length with a signed integer is not
optimal, so change its type to `size_t`.
Change-Id: Ic0c2b7e081ba32d917409568ee53007d9ab7f8f3
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/4768
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Change-Id: If58854c35dce83bf6db7a84a8cb441cc3e60d6d4
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/6529
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
You might want to use the serial hardware for something other than a console,
or you might want to intercede in the serial stream to wrap it in another
protocol. This is what you'd do to send output to GDB while using it to debug
the payload.
Change-Id: I2218c0dbb988dacb64e5bdaf5d92138828eff8b6
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: https://chromium-review.googlesource.com/179559
Reviewed-by: Ronald Minnich <rminnich@chromium.org>
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Commit-Queue: Gabe Black <gabeblack@chromium.org>
Tested-by: Gabe Black <gabeblack@chromium.org>
(cherry picked from commit da9ab46d974745125fe7d8b29ce43336c3586cd5)
Signed-off-by: Isaac Christensen <isaac.christensen@se-eng.com>
Reviewed-on: http://review.coreboot.org/6547
Tested-by: build bot (Jenkins)
|
|
While vendor specific extension blocks are mostly opaque to us,
they're not exactly "unknown".
Change-Id: I9136c04d12045ad13ef4f942c0814c4df88bdf6b
Found-by: Coverity Scan
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/6563
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
The process probably terminates not much later, but in
case anyone reuses the function in something with
longer life-time, free unused resources.
Change-Id: I10c471ee3d9dc9a3ebf08fe4605f223ea59b990e
Found-by: Coverity Scan
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/6559
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Otherwise the following write might end up anywhere.
Change-Id: Ie42d984824e9308bd58b8bb905b6ea823543adf0
Found-by: Coverity Scan
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/6560
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Testing if an unsigned long is greater than ULONG_T_MAX isn't very
useful. The second half of the test checked for too small values
(ie. <= -ULONG_T_MAX).
In both cases errno is set to ERANGE, so just check for that.
Change-Id: I92bad9d1715673531bef5d5d5756feddeb7674b4
Found-by: Coverity Scan
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/6568
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Change-Id: I7467d4a947e9e447707e1370b7e639ddddc20d3d
Found-by: Coverity Scan
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/6570
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
As a follow up to #6479 (63e1948643fcbd763c83b6baa6cd9a077d49f1fc),
fix the remaining faulty loop.
Change-Id: I2c77efe620c71e939f4d74e48f90a166c782e5f5
Found-by: Coverity Scan
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/6569
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <gaumless@gmail.com>
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
|
|
"cbfstool create -B bootblock -s size" (in this order)
would break bootblock selection.
Change-Id: I9a9f5660827c8bf60dae81b519c6f026f3aaa0f3
Found-by: Coverity Scan
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/6564
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
|
|
Change-Id: I4b04f84fb2be7da4b7ffab71bb2c41142f455440
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/6567
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Tested-by: build bot (Jenkins)
|
|
Change-Id: Ib70a6741b55609840b6fd2fca16bcf9883bf143c
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/6566
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Tested-by: build bot (Jenkins)
|
|
Change-Id: I485da5b8e9084c73f16b5df1c42879697fc0ac3d
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/6528
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
|
|
Change-Id: Ia3a846497c220866e950a4b0bb53cb05c0e0cee2
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/6557
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Lets try not to play games with the Lexer with fancy ASCII art. Doxygen
has a more well defined and useful syntax for annotations.
Change-Id: I6f6c58971f509064ae1e28a1740e50e2ae721513
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/6550
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Change-Id: Ic65f8d2cbb5bc459cf513c6b34a5f1846cb2b897
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/6549
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
That extra struct is not needed, we already defined it earlier on.
Also fix coding style in the file.
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Change-Id: I586d290f2f3ba2f44aca7fdee400b88547465599
Reviewed-on: https://chromium-review.googlesource.com/169780
Reviewed-by: Stefan Reinauer <reinauer@google.com>
Commit-Queue: Stefan Reinauer <reinauer@google.com>
Tested-by: Stefan Reinauer <reinauer@google.com>
(cherry picked from commit f7df9f05fb707cac7976cd8a0b36bcf30cef8e0f)
Signed-off-by: Isaac Christensen <isaac.christensen@se-eng.com>
Reviewed-on: http://review.coreboot.org/6532
Tested-by: build bot (Jenkins)
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
|
|
This script is used by 'make menuconfig', but being non executable it
fails to run, causing the make invocation failure.
Setting 'x' mode bits fixes the problem.
Change-Id: I925ca4ee056937b6c38ad34f5520fd621f9d9eb0
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/173564
Reviewed-by: Stefan Reinauer <reinauer@google.com>
Commit-Queue: Stefan Reinauer <reinauer@google.com>
(cherry picked from commit 3ddb9d221ecc3df968853d765b566cf0648a7525)
Signed-off-by: Isaac Christensen <isaac.christensen@se-eng.com>
Reviewed-on: http://review.coreboot.org/6540
Tested-by: build bot (Jenkins)
|
|
Remove the lines added in an apparently unrelated commit 53ad9f58 (Make CONFIG_HAVE_HIGH_TABLES consistent in where and how it is set.)
which touched the symbol HAVE_HIGH_TABLES in all files except this one and
keep those added the same day in commit 6842c029 (Remove MAINBOARD_OPTIONS, which is a relic from early kconfig development.)
Change-Id: Ib055c25a0a0795a50a36e65218c8f31e921f1502
Signed-off-by: Daniele Forsi <dforsi@gmail.com>
Reviewed-on: http://review.coreboot.org/6417
Tested-by: build bot (Jenkins)
Reviewed-by: Isaac Christensen <isaac.christensen@se-eng.com>
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
|
|
Remove spurious includes, unused variables and some wasted new lines.
Re-organise things to be consistent with other superio's.
Change-Id: I959bab2f7a83a1b9160d7f010a0de9638b30cf07
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/6465
Tested-by: build bot (Jenkins)
Reviewed-by: David Hendricks <dhendrix@chromium.org>
|
|
This disables the spread spectrum clock and avoids errata.
Old-Change-Id: I04eb767f1587bb64a215a92b66cd05e099d29964
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/66673
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
(cherry picked from commit a7bf0d818c431221f4d014e3a0130bec8db7406e)
falco: Remove RTD2132 driver from kconfig
Original-Change-Id: I89ad9fbfbc58878602ed85ada918524426b5bc77
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/66946
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
(cherry picked from commit 1d732eb5e4743546b8ed50c8c44965a687f61ab2)
Conflicts:
src/mainboard/google/falco/Kconfig
Old-Change-Id: I317a0741779e272ad72b7272ef6f4a67abd66698
Reviewed-on: https://chromium-review.googlesource.com/167311
Tested-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Commit-Queue: Duncan Laurie <dlaurie@chromium.org>
(cherry picked from commit ffa6c89fbac04b4b6fceafd4ba97d39a285c4aa3)
Squashed two commits and corrected the subject line from 2312
to 2132.
Change-Id: If4f1e59999b70efe2de45522ba78051d9ed88dd7
Signed-off-by: Isaac Christensen <isaac.christensen@se-eng.com>
Reviewed-on: http://review.coreboot.org/6527
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Register range 0x4f000 - 0x4f08f includes scratchpad registers. Fastboot
works fine with these registers removed and graphics is initialized properly
Change-Id: Ic57c526a90619f4a073690440f6c5ac6ca96bf10
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/65755
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Commit-Queue: Furquan Shaikh <furquan@chromium.org>
Tested-by: Furquan Shaikh <furquan@chromium.org>
(cherry picked from commit 7e7befdc3956cbc28d346545669cb55c566cf3ea)
Signed-off-by: Isaac Christensen <isaac.christensen@se-eng.com>
Reviewed-on: http://review.coreboot.org/6525
Tested-by: build bot (Jenkins)
|
|
Change-Id: I778ea787b20a7d7d7b202b1b5e7f956d2fde6629
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: https://chromium-review.googlesource.com/169621
(cherry picked from commit 499a4802b5ad070a0b82f3b291073aa05fa7946e)
Signed-off-by: Isaac Christensen <isaac.christensen@se-eng.com>
Reviewed-on: http://review.coreboot.org/6523
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
On ARM the SPI flash is not memory mapped. Use the CBFS
interface to map the correct portion.
Change-Id: I8ea9aa0119e90a892bf777313fdc389c4739154e
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: https://chromium-review.googlesource.com/169781
Reviewed-by: David Hendrix <dhendrix@chromium.org>
(cherry picked from commit a263d3717e82c43fe91e7c4e82d167e74bf27527)
Signed-off-by: Isaac Christensen <isaac.christensen@se-eng.com>
Reviewed-on: http://review.coreboot.org/6522
Tested-by: build bot (Jenkins)
Reviewed-by: David Hendricks <dhendrix@chromium.org>
|
|
Change-Id: I01a11923fc1b250afeed36acc20793fd072421ba
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: https://chromium-review.googlesource.com/168574
Reviewed-by: Gabe Black <gabeblack@chromium.org>
(cherry picked from commit 46b5f64096c55d0d9627cb9537fc4910e1bddcd9)
Signed-off-by: Isaac Christensen <isaac.christensen@se-eng.com>
Reviewed-on: http://review.coreboot.org/6520
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
|
|
The ALC283 needs a double function reset to ensure that all settings
are reset and the firmware beep is functional.
Original-Change-Id: Id9ddc6f4914957f39c5f9cdfaaac354808929146
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/167291
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Commit-Queue: Duncan Laurie <dlaurie@google.com>
(cherry picked from commit c59865ac464af308baedcd69aa662f46ff3a04d3)
Change-Id: Ie6f3a8179376bc97a6d22712dd965f5e0e6ec5d6
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/167313
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
(cherry picked from commit b31d7a31b838e67a4b7f33119a3baea049d30a36)
Signed-off-by: Isaac Christensen <isaac.christensen@se-eng.com>
Reviewed-on: http://review.coreboot.org/6518
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
|
|
Currently the workaround for indicating a "full" battery kicks
in at 3%, but this turns out to be too high for some devices.
So move the workaround start point to 6% from full, or 94%.
Change-Id: Ib4305df3a68e89f3a10a096d0e89d8105ea9037b
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/169549
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
(cherry picked from commit 982dc496a0553c90dee56fda6411b7c21a5d7da9)
Signed-off-by: Isaac Christensen <isaac.christensen@se-eng.com>
Reviewed-on: http://review.coreboot.org/6521
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Change-Id: Ia2e5427fec1bfff9babb9c59a3878323277f4f4c
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/66555
Commit-Queue: Ronald G. Minnich <rminnich@chromium.org>
Tested-by: Ronald G. Minnich <rminnich@chromium.org>
Reviewed-by: Gabe Black <gabeblack@chromium.org>
(cherry picked from commit 2b96235123d55db3ff5ae5c2454b65de831a1c18)
Signed-off-by: Isaac Christensen <isaac.christensen@se-eng.com>
Reviewed-on: http://review.coreboot.org/6524
Tested-by: build bot (Jenkins)
|
|
This patch ports the USB A-A firmware upload functionality from
exynos5250 over to exynos5420. Essentially just like a conflictless
cherry-pick of 9e69421f5f0eebf88c09913dee90082feab2856c. It also fixes
the exact same bug with SPI initialization for Pit and Kirby.
Old-Change-Id: Ief0ed54c0beb2701e51201041f9bc426b2167747
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/65751
Reviewed-by: David Hendricks <dhendrix@chromium.org>
(cherry picked from commit 5dff43f929478f83939221df13b961a69f89b132)
exynos5: Fix trivial style nits
A few curly braces on the wrong line.
Old-Change-Id: I4ddac4476c6509dc1716e8c1915fbdb67d346786
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/66153
Reviewed-by: Ronald G. Minnich <rminnich@chromium.org>
(cherry picked from commit 41e3fd9eaafe36433723f4e96a6d94c04e5fbafb)
Squashed two related commits.
Change-Id: I22d579693b5e7270aacb45bbe3557e40893dd1f8
Signed-off-by: Isaac Christensen <isaac.christensen@se-eng.com>
Reviewed-on: http://review.coreboot.org/6500
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
|
|
Change-Id: Ifc7208400b0bdfa2b9b70773bd24e9f9df7f8048
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/6526
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
|
|
Alphabetise includes to avoid duplication.
Change-Id: I7fa6998cd736bad2bab4a6b1a65d48a21d6220d9
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/6415
Tested-by: build bot (Jenkins)
Reviewed-by: Isaac Christensen <isaac.christensen@se-eng.com>
|
|
These functions add support for cooperative multitasking.
Currently, since we only have one ARM SOC that uses or supports multitasking,
arch_get_thread_stackbase returns CONFIG_STACK_BOTTOM for the thread stack.
We may end up having to make a cpu-specific function that arch_get_thread_stackbase calls,
but let's avoid adding complexity until we're sure we need to. We also wish to avoid
creating Yet Another Config Variable but will do so if pressed.
The switch code only saves r4-r11 and lr, which is consistent with the standard.
Change-Id: I0338a9c11127351e1f3a190bc51a7a558420b141
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/66845
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Commit-Queue: Ronald G. Minnich <rminnich@chromium.org>
Tested-by: Ronald G. Minnich <rminnich@chromium.org>
(cherry picked from commit 22b62af3c26b6b504498b434d29a56a8932f3061)
Signed-off-by: Isaac Christensen <isaac.christensen@se-eng.com>
Reviewed-on: http://review.coreboot.org/6517
Tested-by: build bot (Jenkins)
|
|
The "bufferable" bit was erroneously set for the writethrough policy
making it the same as writeback.
(credit to jwerner for pointing this out)
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Change-Id: I567d57f0e522cb4b82988894ba9b4638642bf8db
Reviewed-on: https://chromium-review.googlesource.com/167323
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: David Hendricks <dhendrix@chromium.org>
Tested-by: ron minnich <rminnich@chromium.org>
Commit-Queue: David Hendricks <dhendrix@chromium.org>
(cherry picked from commit 36cf13839604c349692865475f3011afd08965b4)
Signed-off-by: Isaac Christensen <isaac.christensen@se-eng.com>
Reviewed-on: http://review.coreboot.org/6515
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
|
|
For many boards, the EDID is known and is set in the ramstage. Reading
the EDID is slow and if we have it we do not want to reread it.
If the raw_edid struct member is non-null, skip reading the EDID.
Change-Id: I63fb11aa90b2f739a351cdc3209faac2713ea451
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: https://chromium-review.googlesource.com/167116
Reviewed-by: Gabe Black <gabeblack@google.com>
Tested-by: ron minnich <rminnich@chromium.org>
Commit-Queue: Ronald Minnich <rminnich@google.com>
(cherry picked from commit 80f48655570de544a7e1939c4f5f28713f11d829)
Signed-off-by: Isaac Christensen <isaac.christensen@se-eng.com>
Reviewed-on: http://review.coreboot.org/6514
Tested-by: build bot (Jenkins)
|
|
Architecture provides a function for thread stack base, thread code uses it.
Build and boot tested on Falco with multitasking on and off.
Change-Id: I5016fab47f9954379acf7702ac7965b0a70c88ed
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/66578
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Commit-Queue: Ronald G. Minnich <rminnich@chromium.org>
Tested-by: Ronald G. Minnich <rminnich@chromium.org>
(cherry picked from commit 3c6afef30c1a0ad6fba0fb76acc792184d924247)
Signed-off-by: Isaac Christensen <isaac.christensen@se-eng.com>
Reviewed-on: http://review.coreboot.org/6513
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
|
|
Set the CLK_DIV_CPERI1 value as recommended by the
0.02 UM section 7.9.1.25.
This suggests to use 0x3F3F0000 as the value to be
set to save power.
This is ported from https://gerrit.chromium.org/gerrit/#/c/64905
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Change-Id: I89a6a72d20374a513019a272628a05e139b31773
Reviewed-on: https://gerrit.chromium.org/gerrit/66787
Commit-Queue: David Hendricks <dhendrix@chromium.org>
Tested-by: David Hendricks <dhendrix@chromium.org>
Reviewed-by: Ronald G. Minnich <rminnich@chromium.org>
(cherry picked from commit 34be13b008e262c641268b7c1c6a08e49f18fc37)
Signed-off-by: Isaac Christensen <isaac.christensen@se-eng.com>
Reviewed-on: http://review.coreboot.org/6512
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
This improves firmware boot time substantially. Because cbmem isn't available
yet, we need to allocate some space in sram for the ttb. Doing cache
initialization in the bootblock means we can implement this once per CPU
instead of once per mainboard.
Old-Change-Id: Iad339de24df8ec2e23f91fe7bf57744e4cc766c5
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/65938
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Commit-Queue: Gabe Black <gabeblack@chromium.org>
Tested-by: Gabe Black <gabeblack@chromium.org>
(cherry picked from commit c32b9b32ad933e627b9ea98434b392239b1fea73)
exynos5420: flush caches and disable MMU in resume path
This patch flushes the caches and disables the MMU before resuming.
c32b9b3 ("Set up caching in the bootblock.") had a bug where the
dcache and MMU remained enabled in the resume path. This caused
the machine to hang on resume. However, other bugs were preventing
us from testing this properly earlier on so it went unnoticed until
now.
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Old-Change-Id: Ib1774f09d286a4d659da9fc2dad1d7a6fc1ebe5e
Reviewed-on: https://chromium-review.googlesource.com/67007
Reviewed-by: ron minnich <rminnich@chromium.org>
Commit-Queue: David Hendricks <dhendrix@chromium.org>
Tested-by: David Hendricks <dhendrix@chromium.org>
(cherry picked from commit 4fdf9763d25f70fd1e3591f6ff9785f78dd6170d)
Squashed two related commits.
Change-Id: Ibd42b28bb06930159248130e5ceaddb3b4b6cc2a
Signed-off-by: Isaac Christensen <isaac.christensen@se-eng.com>
Reviewed-on: http://review.coreboot.org/6511
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
|
|
Call thread_yield_microseconds in udelay. This works with and without
COOP_MULTITASKING enabled.
Change-Id: Ib3eab00d1630dc4daada850e7458ab89702d1864
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/66327
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Commit-Queue: Ronald G. Minnich <rminnich@chromium.org>
Tested-by: Ronald G. Minnich <rminnich@chromium.org>
(cherry picked from commit 12e55ba8a68e5d40e08ad169848bdf274887ce0b)
Signed-off-by: Isaac Christensen <isaac.christensen@se-eng.com>
Reviewed-on: http://review.coreboot.org/6510
Tested-by: build bot (Jenkins)
|
|
The printing routines of the cbfs_payload_segment assumed the type
could be accessed in host order. Each of the fields need to be
converted to the host order before inspecting the fields. In addition,
this removes all the ntoh*() calls while processing the
cbfs_payload_segment structures.
cbfstool would crash adding entries or just printing entries
containing a payload when -v was passed on the command line.
Change-Id: Iff41c64a99001b9e3920e2e26828c5fd6e671239
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/6498
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <gaumless@gmail.com>
|
|
Add verb setting for beep during recovery and dev mode.
Requires depthcharge CL.
Change-Id: I13cbb4e889ebc4c27bb4ab9fa49601b03e872d09
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/66519
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Dylan Reid <dgreid@chromium.org>
Commit-Queue: Duncan Laurie <dlaurie@chromium.org>
(cherry picked from commit c072543946b317192a8e80a744c1515deb414456)
Signed-off-by: Isaac Christensen <isaac.christensen@se-eng.com>
Reviewed-on: http://review.coreboot.org/6502
Tested-by: build bot (Jenkins)
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
|
|
Change-Id: I1144e9d6d6c4278842fdd36743c8a88555f81707
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/65912
Reviewed-by: Ronald G. Minnich <rminnich@chromium.org>
Commit-Queue: Stefan Reinauer <reinauer@chromium.org>
Tested-by: Stefan Reinauer <reinauer@chromium.org>
(cherry picked from commit 95b518877edc88347ce9725ffee32f3aed0de7dc)
Signed-off-by: Isaac Christensen <isaac.christensen@se-eng.com>
Reviewed-on: http://review.coreboot.org/6505
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Shorten a few delays, and make some delays shorter but let the
loops have a higher termination count (i.e. give it the same
amount of time to warm up, but check more frequently).
Change-Id: Id9fe846ae3a8d792b14d62aea4e98d8aad05be43
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/66156
Commit-Queue: Ronald G. Minnich <rminnich@chromium.org>
Tested-by: Ronald G. Minnich <rminnich@chromium.org>
Reviewed-by: Stefan Reinauer <reinauer@google.com>
(cherry picked from commit a112e77f2f21f41f982ca22bebdac213cc8d233a)
Signed-off-by: Isaac Christensen <isaac.christensen@se-eng.com>
Reviewed-on: http://review.coreboot.org/6506
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
|
|
The DWMMC controller internally divided clock by values in CLKSEL registers,
so we must adjust MMC clock for that.
Change-Id: I44f55b634cfc6fd81d76631595b6928c862a219f
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/66657
Commit-Queue: Ronald G. Minnich <rminnich@chromium.org>
Reviewed-by: Ronald G. Minnich <rminnich@chromium.org>
Tested-by: Ronald G. Minnich <rminnich@chromium.org>
Reviewed-by: David Hendricks <dhendrix@chromium.org>
(cherry picked from commit 89ed6c9154f16c6b8d01af03c0b78914773eb469)
Signed-off-by: Isaac Christensen <isaac.christensen@se-eng.com>
Reviewed-on: http://review.coreboot.org/6504
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
|
|
On x86, cpu_info lives at the top of stack. Make the arm do that as
well, as the threading model needs that and so will multicore support.
As part of this change, make the stack size a power of 2.
Also make it much smaller -- 2048 bytes is PLENTY for ram stage.
Note that the small stack size is counterintuitive for rom stage. How
can this work in rom stage, which needs a HUGE stack for lzma? The
main use of STACK_SIZE has always been in ram stage; since 2002 or so
it was to size per-core stacks (see, e.g.,
src/arch/x86/lib/c_start.S:.space CONFIG_MAX_CPUS*CONFIG_STACK_SIZE
and, more recently, thread stacks. So, we define the STACK_TOP for rom
and ram stage, but the STACK_SIZE has no real effect on the ROM stage
(no hardware red zones on the stack) and hence we're ok with actually
defining the "wrong" stack size. In fact, the coreboot_ram ldscript
for armv7 sizes the stack by subtracting CONFIG_STACK_BOTTOM from
CONFIG_STACK_TOP, so we replicate that arithmetic in bootblock.inc
Observed stack usage in ramstage:
BS: BS_PAYLOAD_LOAD times (us): entry 1 run 153887 exit 1
Jumping to boot code at 23104044
CPU0: stack: 02072800 - 02073000, lowest used address 020728d4, stack used: 1836 bytes
entry = 23104044
Which means we do need 2K, not 1K.
Change-Id: I1a21db87081597efe463095bfd33c89eba1d569f
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: https://gerrit.chromium.org/gerrit/66135
Reviewed-by: Ronald G. Minnich <rminnich@chromium.org>
Tested-by: Ronald G. Minnich <rminnich@chromium.org>
Commit-Queue: Ronald G. Minnich <rminnich@chromium.org>
(cherry picked from commit f011097e9f2bfb2f4c1109d465be89a79a65ba3e)
Signed-off-by: Isaac Christensen <isaac.christensen@se-eng.com>
Reviewed-on: http://review.coreboot.org/6501
Tested-by: build bot (Jenkins)
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Change-Id: I7332eeed244877252074e661f1c256a69a9b428a
Signed-off-by: Vladimir Serbinenko <phcoder@gmail.com>
Reviewed-on: http://review.coreboot.org/6482
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
As was done for the reference boards in:
cd30951 mainboard/amd: De-ASCIIartify reference boards
Change-Id: Ie34aa5269388b771daa6934f8aff0314ac6778d5
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/6290
Tested-by: build bot (Jenkins)
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
|
|
Gizmo sends two southbridge GPP PCIe lanes to its high speed
edge connector. This change will allow developers to create
two x1 slots on an extender card.
Change-Id: Iba6c1a4caf7846d12e3960775d7bc906ca8ff385
Signed-off-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-on: http://review.coreboot.org/6499
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Change-Id: I05cea020e77051bd3bc0e93b0c70e12b9b985d05
Signed-off-by: Edward O'Callaghan <eocallaghan@alterapraxis.com>
Reviewed-on: http://review.coreboot.org/6398
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
