| Age | Commit message (Collapse) | Author |
|---|
|
When a new variant is created, it needs to have a path to its SPD binary
defined. Currently, this is done by setting SPD_SOURCES to a placeholder
SPD file, which just contains zero bytes.
To remove the need for a placeholder file, automatically generate a
single-byte spd.bin in lib/Makefile.inc when SPD_SOURCES is set to the
marker value 'placeholder'.
BUG=b:191776301
TEST=Change cappy/memory/Makefile to `SPD_SOURCES = placeholder`. Build
and check that spd.bin contains a single zero byte.
Signed-off-by: Reka Norman <rekanorman@google.com>
Change-Id: I11f8f9b7ea3bc32aa5c7a617558572a5c1c74c72
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57795
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Move existing UART driver from sc7180 to common folder.
This implements UART driver for QCOM SoC's
BUG=b:182963902
TEST=Validated on qualcomm sc7180 and sc7280 development board.
Signed-off-by: Rajesh Patil <rajpat@codeaurora.org>
Change-Id: I7bc2d3765f956e04bae3e45c3a9b9e2ad424c7b1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55954
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shelley Chen <shchen@google.com>
|
|
Enable programming of Type-C AUX DC bias GPIOs.
BUG=b:199833078
TEST=Verify that a Type-C monitor works when connected in both
orientations.
Signed-off-by: Joey Peng <joey.peng@lcfc.corp-partner.google.com>
Change-Id: I4f6d80a9f2fc8cdc93226d6c234b54e5db830d71
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57643
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Before this patch, gpio_configure_pads_with_override called
program_gpios once for each GPIO that needed to be configured which
resulted in base_num_pads - 1 unneeded master_switch_set/
master_switch_clr sequences for the gpio_configure_pads_with_override
call. Instead implement gpio_configure_pads_with_override as the more
generic function and program_gpios as a special case of that which
passes an empty override configuration and override pad number to
gpio_configure_pads_with_override.
TEST=GPIO configuration and multiplexer register values are the same for
all GPIOs on google/guybrush right before jumping to the payload before
and after the patch.
Change-Id: Ia8e47b2a278a1887db5406c1f863ddafa6a68675
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43050
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Change-Id: I3965a90151bd9250a87dabc715d68a39699ff9e1
Signed-off-by: Jeremy Soller <jeremy@system76.com>
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48422
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Change-Id: I5dd3bc320ca640728e1d86180c6bfa0dc7295760
Signed-off-by: Jeremy Soller <jeremy@system76.com>
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48421
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
This change copies ec_commands.h directly from Chromium OS EC repo at
sha 8c2c6bd5b1d44b367929af498d4d4b0df126a4ef.
BUG=b:188073399
TEST=Build coreboot
BRANCH=None
Change-Id: I674cb860adb6b8497a8aecf47952ed8f85ddaa70
Signed-off-by: Rob Barnes <robbarnes@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57758
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
|
|
Earlier generation platform used `HeciEnabled` chip config (set to 0)
and HECI_DISABLE_USING_SMM Kconfig to make the CSE function disable at
the end of the post. `HeciEnabled` chip config remains enabled in all
latest generation platforms hence drop HECI_DISABLE_USING_SMM Kconfig
selection from SoC Kconfig as CSE remains default enabled.
BUG=b:200644229
TEST=No functional impact during boot as CSE (B:0, D:0x16, F:0) device
is listed with `lspci`.
Change-Id: I5278e5c2e015b91bb3df3a3c73a6c659a56794b5
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57799
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
|
|
Update codec/amp setting.
1. Update hid for ALC5682VS
2. Add maxim properties.
BUG=b:197076844
TEST=build and check SSDT
Change-Id: I8bedd4d0737caf46769ad27bce1768c225ce8a82
Signed-off-by: Wisley Chen <wisley.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57753
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
The current power sequencing for the SSD does not work in a non-serial
enabled BIOS image. It appears that the FSP scans the PCIe RPs before
the SSD has time to prepare itself for PCIe, so the FSP disables the RP
and so depthcharge cannot find a boot disk.
Changing the power sequence timing to enable power in bootblock and
deassert reset in ramstage follows the SSD's power sequence and
allows it to be discovered by the FSP so the RP does not get disabled.
BUG=b:199714453
TEST=build, boot into SSD, and run reboot stress test.
Change-Id: I5e7943a6cc88bc02bcbd97a1086b2d8044d7b1c3
Signed-off-by: Wisley Chen <wisley.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57583
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
In this file bool, uint8_t and uint32_t are used, so include types.h
directly to have those types defined instead of relying to have those
included indirectly via amdblocks/gpio_banks.h.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I6f4626a50219fab818e8bc5087961a731b44e71b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57788
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
This implements the SPI driver for the QUP core.
BUG=b:182963902
TEST=Validated on qualcomm sc7180 and sc7280 development board.
Signed-off-by: Rajesh Patil <rajpat@codeaurora.org>
Change-Id: I7e5d3ad07f68255727958d53e6919944d3038260
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56399
Reviewed-by: Shelley Chen <shchen@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=b:182963902
TEST=Validated on qualcomm sc7280 developement board
Signed-off-by: Rajesh Patil <rajpat@codeaurora.org>
Change-Id: I34a45422e38ea3a47f29e9856fc5679e8aebbcdf
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55962
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shelley Chen <shchen@google.com>
|
|
This implements qup spi driver for qualcomm chipsets
Rename header file names for trogdor to prevent breakage.
BUG=b:182963902
TEST=Validated on qualcomm sc7180 and sc7280 development board.
Signed-off-by: Rajesh Patil <rajpat@codeaurora.org>
Change-Id: I2f2b25b6661fcd518f70383da0c7788c5269c97b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55953
Reviewed-by: Shelley Chen <shchen@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=b:182963902
TEST=Validated on qualcomm sc7280 developement board
Signed-off-by: Rajesh Patil <rajpat@codeaurora.org>
Change-Id: I58c2b79ea2feeab0ad4c2b7cdaa041984160a7ae
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55961
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shelley Chen <shchen@google.com>
|
|
copy existing I2C driver from /soc/qualcomm/sc7180 to common folder.
This implements i2c driver for qualcomm chipsets
BUG=b:182963902
TEST=Validated on qualcomm sc7180 and sc7280 development board
Signed-off-by: Rajesh Patil <rajpat@codeaurora.org>
Change-Id: I16e6fc2c1c24b9814d1803bffd5cfbb657201cfb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55952
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shelley Chen <shchen@google.com>
|
|
Load GSI FW in ramstage and make it part of RW
BUG=b:182963902
TEST=Validated on qualcomm sc7280 development board.
Signed-off-by: Rajesh Patil <rajpat@codeaurora.org>
Change-Id: I3d9caa0921fcf9ad67f1071cdf769a99fb6d1a30
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55964
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shelley Chen <shchen@google.com>
|
|
Loading QUP FW as per herobrine and piglin configuration
for I2C, SPI and UART.
As part of the code clean up, update the header files of the
QUP drivers with the correct path.
BUG=b:182963902
TEST=Validated on qualcomm sc7280 development board.
Signed-off-by: Rajesh Patil <rajpat@codeaurora.org>
Change-Id: Ic218c6a91ffc4484830446d707d1f3403e2dc46b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57672
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shelley Chen <shchen@google.com>
|
|
Enable common qup driver in sc7280
BUG=b:182963902
TEST=Validated on qualcomm sc7280 development board
Signed-off-by: Rajesh Patil <rajpat@codeaurora.org>
Change-Id: I0e9049557ff63898037210e72333e1739ab62413
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55960
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Shelley Chen <shchen@google.com>
|
|
Currently, if LIB_SPD_DEPS contains an SPD file which doesn't exist, the
file is silently skipped when creating spd.bin. Instead, fail the build.
BUG=b:191776301
TEST=Build test on brya. Build fails if a non-existent file is included
in LIB_SPD_DEPS.
Change-Id: I1bdadb72e087c2ee7a88fbab2f3607bd400fa2e4
Signed-off-by: Reka Norman <rekanorman@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57697
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
BUG=b:191776301
TEST=dewatt build no longer fails when a check for non-existent files
in LIB_SPD_DEPS is added (following commit).
Signed-off-by: Reka Norman <rekanorman@google.com>
Change-Id: Iee0c5e8b71f7cc7c016a38a60569daff99a55027
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57702
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Add a 'Generated by' string to the generated Makefile.inc and
dram_id.generated.txt, showing the command used to generate the files.
BUG=b:191776301
TEST=Run part_id_gen, check that the generated files contain the string
Signed-off-by: Reka Norman <rekanorman@google.com>
Change-Id: Ic9a7826212a732288f36f111b7bc20365a1f702d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57692
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Currently, one of the arguments to part_id_gen is the directory
containing the SPD files, e.g. spd/lp4x/set-0. This requires the user of
the tool to understand the spd/ directory structure, and manually look
up the set number corresponding to their platform.
Change part_id_gen to take the platform and memory technology as
arguments instead of the SPD directory, and automatically determine the
SPD directory by reading the platforms manifest file generated by
spd_gen.go.
BUG=b:191776301
TEST=Run part_id_gen and check that the generated Makefile.inc and
dram_id.generated.txt are the same as before. Example:
util/spd_tools/bin/part_id_gen \
ADL \
lp4x \
src/mainboard/google/brya/variants/kano/memory \
src/mainboard/google/brya/variants/kano/memory/mem_parts_used.txt
Change-Id: I7cd7243d76b5769e8a15daa56b8438274bdd8e96
Signed-off-by: Reka Norman <rekanorman@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57586
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Currently, the maximum part ID of 15 is enforced only for manually
assigned IDs. Also enforce it for automatically assigned IDs.
BUG=b:191776301
TEST=part_id_gen fails when the number of part IDs which would be
assigned is greater than MaxMemoryId.
Signed-off-by: Reka Norman <rekanorman@google.com>
Change-Id: I802190a13b68439ccbcdb28300ccc5fd1b38a9c9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57691
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Remove the override in guybrush devicetree that configured in-band eSPI
alerts. This will result in guybrush using dedicated open-drain eSPI
alerts. Guybrush boards must be reworked to connect the eSPI alert line,
otherwise they will not boot with this change
BUG=b:198596430
TEST=Boot on reworked guybrush
BRANCH=None
Change-Id: I185eec773336fb662d9fe7f4c11991813e4d7cd6
Signed-off-by: Rob Barnes <robbarnes@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57778
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add SPD support for DDR4 memory part
BUG=b:199469240
TEST=none
Signed-off-by: Frank Wu <frank_wu@compal.corp-partner.google.com>
Change-Id: Ie67cf6b90304f0bcf80838866c7461c0cea86dc3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57550
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
The aliases are defined in the chipset devicetree, so the device
pointers will be available for all boards using this SoC.
TEST=None
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Id4c921575e978bb29e61f35e78ff2a1711acf06a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57780
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
The aliases are defined in the chipset devicetree, so the device
pointers will be available for all boards using this SoC.
TEST=None
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Id655e9eba9b8e9898fa01bf03876074e136cc7c6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57779
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This reverts commit a2c009bd94aa3c9694158f9e28184ccbd94df42b.
Reason for revert: Breaks parallel abuilds.
Change-Id: I368b189050d519769f4852fea8e255e9b31b27b6
Signed-off-by: Reka Norman <rekanorman@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57590
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
This change drops the function `find_gfx_dev()` as it is unused now.
Change-Id: Ie42707bd45348dc7485ca0ca12ebff2994897e6b
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57746
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
This change replaces the device tree walks with device pointers by
adding alias for igpu (integrated graphics) device in the tree.
Change-Id: I6d159f6dc674f4a0b38ebb553c5141105405a883
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57745
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
This change replaces the device tree walks with device pointers by
adding alias for following devices:
1. FPMCU
2. WWAN
Additionally, this change drops the __weak attribute for variant_has_*
functions as there is no need for different implementations for the
variants.
Change-Id: I8af5e27f226270e6b40a50640c87de99a5a703f7
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57743
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
On some dedede variants, USB port 2.3/3.3 might be connected to either
LTE device or Type-A external port depending upon FW_CONFIG. Commit
856b579 ("mb/google/dedede/var/kracko: Update LTE USB port
configuration") enabled Type-A external port by default in override
tree and updated the config dynamically for LTE USB device if
FW_CONFIG indicated support for it. This was required because sconfig
lacked the support for multiple override devices. Commit
b9c22e0 ("util/sconfig: Compare probe conditions for override device
match") fixed this behavior in sconfig and now we can add multiple
override devices using different FW_CONFIG probe statements in
override tree. Hence, this change moves the LTE USB device to override
tree for metaknight, kracko and drawcia variants.
In addition to that, drawcia needs to be update reset_gpio depending
upon board_id. Thus, alias `lte_usb2` is used in drawcia override tree
to fix the reset_gpio for older boards i.e. board_id <= 9.
Change-Id: Ie5b205594680d9c2b8543c5c99325d95620cafd2
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57742
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
On sasukette, codec device might be either 10EC5682 or RTL5682
depending upon the provisioned FW_CONFIG value for
AUDIO_CODEC_SOURCE. The HID for the device was updated in ramstage.c
because sconfig lacked the support for multiple override
devices. Commit b9c22e0 ("util/sconfig: Compare probe conditions for
override device match") fixed this behavior in sconfig and now we can
add multiple override devices using different FW_CONFIG probe
statements in override tree. Hence, this change moves the codec device
to override tree and drops the special handling in ramstage.c
This change also probes for UNPROVISIONED value of FW_CONFIG for
"10EC5682" device since some devices might have shipped with
UNPROVISIONED value and using "10EC5682" device.
Change-Id: I909a29c3df0cbb7ac3c07ca7663a49ad47007232
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57741
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
This CL fixes a compilation error that happens in 32-bit platforms.
This error happens because printf() was using %ld instead of %zu to
print size_t variables.
This CL fixes it.
BUG=b:200608182
TEST=emerge-kevin (ARM 32-bit)
TEST=emerge-eve (Intel 64-bit)
Change-Id: I340e108361c052601f2b126db45caf2e35ee7ace
Signed-off-by: Ricardo Quesada <ricardoq@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57792
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
|
|
Currently there are two versions of gen_part_id.go, one for LP4x and one
DDR4. This change implements a unified version of this tool.
The new part_id_gen.go is almost identical to the existing
ddr4/gen_part_id.go. The new version was based on the ddr4 version and
not the lp4x version, since the ddr4 version contains extra logic to
support fixed IDs in the mem_parts_used files.
The only non-trivial change from ddr4/gen_part_id.go is to include the
full paths of SPD files in the generated Makefile.inc. E.g. instead of
SPD_SOURCES += lp4x-spd-1.hex
the full path relative to the coreboot root directory is included:
SPD_SOURCES += spd/lp4x/set-0/spd-1.hex
BUG=b:191776301
TEST=For each variant of brya/volteer/dedede/guybrush/zork, run
part_id_gen and verify that the generated Makefile.inc and
dram_id.generated.txt are identical to those currently in the src tree,
except for the modified SPD file paths in Makefile.inc.
Example:
util/spd_tools/bin/part_id_gen \
spd/lp4x/set-0 \
src/mainboard/google/brya/variants/kano/memory \
src/mainboard/google/brya/variants/kano/memory/mem_parts_used.txt
Change-Id: Ib33d09076f340f688519dae7956a2b27af090c0b
Signed-off-by: Reka Norman <rekanorman@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57585
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
When a new variant is created, its SPD_SOURCES contains a placeholder
file, to avoid a build failure due to SPD_SOURCES being empty. Currently
these placeholder files live with the rest of the SPD files in soc and
mainboard directories, e.g.
src/soc/intel/alderlake/spd/placeholder.spd.hex
Add a similar placeholder SPD file to the new spd/ directory.
BUG=b:191776301
TEST=None
Signed-off-by: Reka Norman <rekanorman@google.com>
Change-Id: Ia6d76ed512a7e44221fc93ad960790be575c44c2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57732
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Use the new unified version of the spd_gen tool to generate all LP4x and
DDR4 SPDs, storing them in a new spd/ directory. Storing them in a
common location allows platforms with the same SPD requirements to share
SPD files, reducing duplication compared to storing SPDs in soc/ and
mainboard/ directories.
For each memory technology there are multiple sets of SPDs. Each set
corresponds to a set of platforms with different SPD requirements, e.g.
due to different memory training code expectations. A manifest file
(platforms_manifest.generated.txt) lists the platform -> set mappings.
Commands used to generate SPDs:
cp util/spd_tools/lp4x/global_lp4x_mem_parts.json.txt \
spd/lp4x/memory_parts.json
cp util/spd_tools/ddr4/global_ddr4_mem_parts.json.txt \
spd/ddr4/memory_parts.json
util/spd_tools/bin/spd_gen spd/lp4x/memory_parts.json lp4x
util/spd_tools/bin/spd_gen spd/ddr4/memory_parts.json ddr4
BUG=b:191776301
TEST=None
Signed-off-by: Reka Norman <rekanorman@google.com>
Change-Id: Iac82847a1a0c1f2e7271d0d3b3a7261849813a24
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57514
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
This change replaces the device tree walks with device pointers by
using alias names for the following devices:
1. PMC MUX connector
2. SPI TPM
3. I2C TPM
Change-Id: I38f87d3a90a7253f2a29aba7db9a9f9744985494
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57740
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
This change replaces the device tree walks with device pointers by
adding alias for dptf_policy generic device in the tree.
Change-Id: I8fd5476a9cea84ab8b2678167b3e0504eecacf6c
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57739
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Enable EC keyboard backlight for redrix.
BUG=b:192052098
TEST=FW_NAME=redrix emerge-brya coreboot chromeos-bootimage
Change-Id: I175d8b91b37c6645ab1a7f05fc6915b3b016e3ff
Signed-off-by: Wisley Chen <wisley.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57756
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Create a variant for the QC CRD device.
BUG=b:197366666
BRANCH=None
TEST=./util/abuild/abuild -p none -t GOOGLE_HOGLIN -x -a -B
Change-Id: I883d17b3ad3c7e44a00f0d0e7007c119417c5028
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57720
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Bob Moragues <moragues@google.com>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Normally for vboot-enabled x86 board, the VBNV region is stored in CMOS
and backed up to flash (RW_NVRAM). However, on the very first boot after
a flash of the full SPI image (so RW_NVRAM is empty), if
RTC_BATTERY_DEAD is set, coreboot persistently requests recovery before
FSP-M finishes (which appears to be the current location that
RTC_BATTERY_DEAD is cleared on this platform). This is because
vbnv_cmos_failed() will still return 1. Therefore, immediately after
reading RTC_BATTERY_DEAD, it is cleared. This prevents an infinite boot
loop when trying to set the recovery mode bit.
Note that this was the behavior for previous generations of Intel PMC
programming as well (see southbridge/intel, soc/skylake, soc/broadwell,
etc).
BUG=b:181678769
Change-Id: I95753fa536fae8ca4bb95007419875815c1bcb06
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56672
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
Normally for vboot-enabled x86 board, the VBNV region is stored in CMOS
and backed up to flash (RW_NVRAM). However, on the very first boot after
a flash of the full SPI image (so RW_NVRAM is empty), if
RTC_BATTERY_DEAD is set, coreboot persistently requests recovery before
FSP-M finishes (which appears to be the current location that
RTC_BATTERY_DEAD is cleared on this platform). This is because
vbnv_cmos_failed() will still return 1. Therefore, immediately after
reading RTC_BATTERY_DEAD, it is cleared. This prevents an infinite boot
loop when trying to set the recovery mode bit.
Note that this was the behavior for previous generations of Intel PMC
programming as well (see southbridge/intel, soc/skylake, soc/broadwell,
etc).
BUG=b:181678769
Change-Id: I1a55df754c711b2afb8939b442019831c25cce29
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56671
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
Normally for vboot-enabled x86 board, the VBNV region is stored in CMOS
and backed up to flash (RW_NVRAM). However, on the very first boot after
a flash of the full SPI image (so RW_NVRAM is empty), if
RTC_BATTERY_DEAD is set, coreboot persistently requests recovery before
FSP-M finishes (which appears to be the current location that
RTC_BATTERY_DEAD is cleared on this platform). This is because
vbnv_cmos_failed() will still return 1. Therefore, immediately after
reading RTC_BATTERY_DEAD, it is cleared. This prevents an infinite boot
loop when trying to set the recovery mode bit.
Note that this was the behavior for previous generations of Intel PMC
programming as well (see southbridge/intel, soc/skylake, soc/broadwell,
etc).
BUG=b:181678769
Change-Id: Idfaa9a24f7b7fefa4f63ab8e3bc4ee6a0f1faedf
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56670
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
Normally for vboot-enabled x86 board, the VBNV region is stored in CMOS
and backed up to flash (RW_NVRAM). However, on the very first boot after
a flash of the full SPI image (so RW_NVRAM is empty), if
RTC_BATTERY_DEAD is set, coreboot persistently requests recovery before
FSP-M finishes (which appears to be the current location that
RTC_BATTERY_DEAD is cleared on this platform). This is because
vbnv_cmos_failed() will still return 1. Therefore, immediately after
reading RTC_BATTERY_DEAD, it is cleared. This prevents an infinite boot
loop when trying to set the recovery mode bit.
Note that this was the behavior for previous generations of Intel PMC
programming as well (see southbridge/intel, soc/skylake, soc/broadwell,
etc).
BUG=b:181678769
Change-Id: Ie86822f22aa5899a7e446398370424ca5a4ca43d
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56669
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
Fix the two issues below.
SB800: sb_Before_Pci_Init
shift out of bounds src/vendorcode/amd/cimx/sb800/PCILIB.c:49:18
ubsan: unrecoverable error.
SB800: sb_Before_Pci_Init
shift out of bounds src/vendorcode/amd/cimx/sb800/PCILIB.c:66:18
ubsan: unrecoverable error.
Found by: UBSAN
Change-Id: Id42e62d35f59793bad10998f14422ab7fb4fc029
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51283
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michał Żygowski <michal.zygowski@3mdeb.com>
|
|
This enables runtime power management for the I2C controllers.
BUG=b:182556027, b:183983959
TEST=enable dynamic debug in kernel and check i2c D3/D0 transitions
during suspend_stress_test.
Change-Id: Ia6b9ca95d751f32b7cd701494377f15091c22d2f
Signed-off-by: Julian Schroeder <julianmarcusschroeder@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56462
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This enables runtime power management for the UART controllers.
BUG=b:183983959
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I4e57d6312feda459cec65f330c6d2072774d4eb5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57681
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Add two properties (maxim, vmon-slot-no/maxim, imon-slot-no) in maxim9839 driver.
This is I/V source destination definition that from below properties .
maxim,vmon-slot-no => PCM_IVADC_V_DEST
maxim,imon-slot-no => PCM_IVADC_I_DEST
BUG=b:197076844
TEST=build and check SSDT
Signed-off-by: Wisley Chen <wisley.chen@quanta.corp-partner.google.com>
Change-Id: Idb24d19c7cfea559bf6d53f401d66cadb8b3acc6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57671
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Currently, running abuild in a fresh checkout without having built the
toolchain results in the following confusing behaviour:
1. Run abuild. It fails due to the missing coreboot toolchain, and the
error message suggests running `make crossgcc`.
2. Run `make crossgcc`. It succeeds.
3. Re-run abuild. It still fails due to a missing coreboot toolchain.
This happens because the first abuild run generates an xcompile file
which uses the system toolchain. The second abuild run doesn't
regenerate the xcompile, so it still fails due to the non-coreboot
toolchain.
To avoid this confusing behaviour, regenerate the xcompile file every
time abuild is run.
BUG=None
TEST=Perform the steps above in a clean checkout. The second abuild run
now succeeds.
Signed-off-by: Reka Norman <rekanorman@google.com>
Change-Id: I78a7702c45cecbfe8460ec55df03741e5ced94b3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57651
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Currently, Intel TME (Total Memory Encryption) can be enabled regardless
of SoC support. Add a Kconfig to guard the option depending on actual
support.
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: Ia20152bb0fc56b0aec3019c592dd6d484829aefe
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57762
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
This change provides helper macros for generating pointer name and
weak pointer definition for devices using alias names. This will be
helpful for developers to reference the device pointer with alias
names used in the device tree.
Change-Id: I3a5a3c7fdc2c521bac9ab3336f5a6ebecd621e04
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57738
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
This change uses _dev_${ALIAS_NAME} as the name for `struct device` if
the device has an alias. In addition to that, it emits
_dev_${ALIAS_NAME}_ptr which points to the device structure. This
allows developers to directly reference a particular device in the tree
using alias name without having to walk the entire path. In later CLs,
mainboards are transitioned to use this newly emitted device structure
pointers.
Change-Id: I8306d9efba8e5ca5c0bda41baac9c90ad8b73ece
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57657
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Add get_wifi_sar_cbfs_file_name() to return the wifi SAR file name
BUG=None
TEST=FW_NAME=redrix emerge-brya coreboot
Change-Id: I87e7a30619fd93d0eae692c4c540c29850ff6721
Signed-off-by: Wisley Chen <wisley.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57710
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Add CHROMEOS_WIFI_SAR to include the SAR configs.
BUG=None
TEST=FW_NAME=redrix emerge-brya coreboot
Change-Id: I50a413f3425d0b0e0b5ce71dabf6b9477800795e
Signed-off-by: Wisley Chen <wisley.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57709
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Add manufacturer ID codes for Hynix, Samsung and Micron.
Tested=On OCP Crater Lake, dmidecode -t 17 shows expected info.
Signed-off-by: JingleHsuWiwynn <jingle_hsu@wiwynn.com>
Change-Id: I0b4bbc46d3bfd9e9534cdd59f90cbdc150f29542
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57700
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Daocheng Bu <daocheng.bu@intel.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Change-Id: I9ba7d2af3c9c298fda2b2997d52546cc2f702a82
Signed-off-by: Jeremy Soller <jeremy@system76.com>
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52063
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Change-Id: I3dfa2ab430439d8dc71531b92aa7800db94d603b
Signed-off-by: Jeremy Soller <jeremy@system76.com>
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/52034
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
The Kconfig options for custom SPD values aren't supposed to be part of
the choice block.
Change-Id: I12eb1012f94000b14e5d7f1e5123dddf69ac1a94
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57717
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
USB3 MB doesn't have re-timer. Thus we have to configurate the AUX pin.
For now, we use USB3 DB to determine the USB3 MB.
BUG=b:197907500
TEST=NA
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: Ide45c77e0a6f736a02d5dc9ad05aa1ef9e754fa5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57656
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
To save the S3 power, USB3_HUB_RST_L is externally pulled up to a
weak resistor so we have to reset the hub via GPIO84 as early
as possible. Otherwise the USB3 hub may be not usable.
BUG=b:199822702
TEST=measure voltage of USB3_HUB_RST_L as 1.8V
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Change-Id: Ie87d631e83ede819ee9f9951dfc6517beae50247
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57663
Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.corp-partner.google.com>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Update thermal setting from thermal team.
BUG=b:200134784
TEST=build and verified by thermal team.
Signed-off-by: Wisley Chen <wisley.chen@quanta.corp-partner.google.com>
Change-Id: If74c3bc19cf4abd64d646b842cbb6a61b910e933
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57713
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
The input buffer to the buffer_to_fifo family of functions is only read,
so it can be a const pointer. (Also, remove the MIPS check in libpayload
for these functions... the MIPS architecture has been removed a while
ago.)
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I021069680cf691590fdacc3d51f747f12ae3df31
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57731
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
|
|
SBI comes with its own memset implementation (under a slightly
different name) that gcc11 "helpfully" tries to replace with a call
to memset(). Since we don't provide a memset, the linker isn't happy,
so prevent gcc from doing that.
Change-Id: I3459a519d46a123f873306000b8b2261bd64e0c3
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/56429
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Change-Id: Ia68d4d9f836ad23fb8f6a7203a78b4ea40c7c43b
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/54049
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
We never call console_init from asm, so we don't need the asmlinkage.
This allows us to remove the arch/cpu.h include since we only needed it
for the asmlinkage #define.
BUG=b:179699789
TEST=build guybrush
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I9a7895d4f5cba59f6b05915fa4d6c6fd6ab85773
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57568
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This include provides the definition of enum cb_err.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Idfee720de920377796e3fd64cb47514b8cb08c34
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57730
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Including arch/cpu.h is needed to have the declaration for cpuid_eax,
get_fms and struct cpuinfo_x86.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I18b60f8cf33f71c7215a97ea209b8f8cf66cf42f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57729
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
smp_processor_id is defined in src/arch/arm64/include/armv8/arch/cpu.h.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I0b610189bf439774cb900f74559dee314cbc5854
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57728
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Include device/device.h to have struct device defined and types.h to
have bool, u8, u16 and u32 defined.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I3c5d5a78c2e2dab21432ced5f84665eb78a49d52
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57727
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Migrate the last two platforms to using Kconfig through
`get_valid_prmrr_size()` instead of hardcoded values in the devicetree.
Change-Id: I93aa177f741ca8b2a2d50fae2515606b96784e83
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57674
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
NVMe needs extra time to run boot process, enable power and deassert
reset for NVMe earlier in the boot flow that primus can successfully
boot into OS with non-serial coreboot.
BUG=b:199967106
TEST=USE="project_primus" emerge-brya coreboot and verify it builds
without error.
Signed-off-by: Malik_Hsu <malik_hsu@wistron.corp-partner.google.com>
Change-Id: I9c66efe96515347502d059556052c764c1be5d09
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57658
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Update DPTF parameters from internal thermal team.
BUG=b:197546694
BRANCH=dedede
TEST=emerge-keeby coreboot
Signed-off-by: Sunwei Li <lisunwei@huaqin.corp-partner.google.com>
Change-Id: I71a76a4d94a704aef7b3cefa2fca3009eb765bb6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57693
Reviewed-by: Weimin Wu <wuweimin@huaqin.corp-partner.google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Aseda Aboagye <aaboagye@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Including arch/cpu.h is needed to have the declaration for
cpu_get_feature_flags_ecx.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I091c82f5a55ee9aa84a255c75c7721eff989344d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57726
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Including arch/cpu.h is needed to have the declaration for cpuid_eax.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ic22aba062117e3afa818fa2fc39cb0738e6a1612
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57725
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Apart from the u8, u16 and u32 types, the bool type is used in this file
so include types.h instead of stdint.h to have bool defined too.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I95f037deb0fe11b717586df655065bfbb33b0d23
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57724
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Apart from the bool type, uint8_t, uint32_t and uint64_t are used in
this file, so include types.h instead of stdbool.h.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I30088d68132058f40b974fbaa822f322b58ed6c7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57723
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Both bool and uintptr_t types are used in this file, so include types.h
to have the definitions.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I647d9f50cd6edaf08bebf5d713cd05731fadfc1b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57722
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
These statements fit on a single line. Reflow them to ease future works.
Change-Id: Ie18e9a00f67b999fdcedcab3c28b68e34bc93da4
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/55814
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
Enable USB4 PCIe resources for redrix
BUG=b:192052098
TEST=FW_NAME=redrix emerge-brya coreboot chromeos-bootimage
Change-Id: I759618055b1282653d8a05fa66e8cdab0c43e3a6
Signed-off-by: Wisley Chen <wisley.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57711
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Follow FIBOCOM_L850-GL Hardware User Manual_V1.0.8.
BUG=b:180166408,b:187691798
TEST=measure WWAN power off by scope is meeting the spec.
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I6b2725cd61d5b54bc7fd70a9daffd29e7b43690b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57634
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
When the century byte was reserved, the debug_level was accidentally
converted from an enum to a hidden value. Change it back to an enum.
Fixes: f05bd8830de ("mb/system76/*: cmos.layout: Reserve century byte")
Change-Id: Id88a7aed7b2fc793fd003db5b45f3f201b1a7630
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57682
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jeremy Soller <jeremy@system76.com>
|
|
When using a debug build of the FSP, the FSP-M binary is larger than the
memory region we have allocated for it, so increase the size to make the
binary of the debug build fit in there. Also adjust the VERSTAGE_ADDR so
that it starts right after the the FSP-M memory region.
TEST=coreboot builds now successfully when using a debug version of the
FSP
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ib64806bcf948d5ed4bcf8e1f50004091f125dc7e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57718
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
* cezanne: Remove internal classification from PSP release notes
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I8198a1d88e98a2192ccd2ddadb1842daabf9c02f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57689
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
Currently there are two versions of spd_tools: one for LP4x and one for
DDR4. This change is the first step in unifying these into a single
tool.
This change implements a unified version of the spd_gen tool, by
combining the functionality currently in lp4x/gen_spd.go and
ddr4/gen_spd.go. The unified version takes the memory technology as an
argument, and generates SPD files for all platforms supporting that
technology.
BUG=b:191776301
TEST=Compare the SPDs generated by the old and new versions of the tool
for all supported platforms. For reference, the test script used is
here: https://review.coreboot.org/c/coreboot/+/57511
Signed-off-by: Reka Norman <rekanorman@google.com>
Change-Id: I7fc036996dbafbb54e075da0c3ac2ea0886a6db2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57512
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
To save the space for FW, some of the FWs are going to be defined as
LVL2 entries. To be compatible to "flattened" layout, we still drop
the LVL2 entry to level1 if there is only one level.
Change-Id: Ibe8cdd5c14225899352b02bb19aae6059d56d428
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57063
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
The `CaVrefConfig` FSP-M UPD describes how the on-die Vref generators
are connected to the DRAM. With the exception of an early Skylake RVP
board (which doesn't have coreboot support), mainboards using DDR3 or
LPDDR3 memory should set `CaVrefConfig` to 0, whereas mainboards with
DDR4 should set `CaVrefConfig` to 2. MRC uses this information during
memory training, so it is important to use the correct value to avoid
any issues, such as increased power usage, system instability or even
boot failures.
However, several Skylake DDR4 mainboards don't set `CaVrefConfig` to 2.
Although they can boot successfully, it's not optimal. For boards that
set `DIMM_SPD_SIZE` to 512 (DDR4 SPD size), set `CaVrefConfig` to 2.
Change-Id: Idab77daff311584b3e3061e9bf107c2fc1b7bdf1
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57262
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
Implement _BIX method to expose battery cycle count.
Requires an EC version with support for cycle count.
Change-Id: I5f7a1d275caff59960aaf9c39b9c707970350987
Signed-off-by: Ian Douglas Scott <idscott@system76.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57678
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jeremy Soller <jeremy@system76.com>
|
|
vboot_reference is introducing a new field (ctx) to store the current
boot mode in crrev/c/2944250 (ctx->bootmode), which will be leveraged
in both vboot flow and elog_add_boot_reason in coreboot.
In current steps of deciding bootmode, a function vb2ex_ec_trusted
is required. This function checks gpio EC_IN_RW pin and will return
'trusted' only if EC is not in RW. Therefore, we need to implement
similar utilities in coreboot.
We will deprecate vb2ex_ec_trusted and use the flag,
VB2_CONTEXT_EC_TRUSTED, in vboot, vb2api_fw_phase1 and set that flag
in coreboot, verstage_main.
Also add a help function get_ec_is_trusted which needed to be
implemented per mainboard.
BUG=b:177196147, b:181931817
BRANCH=none
TEST=Test on trogdor if manual recovery works
Signed-off-by: Hsuan Ting Chen <roccochen@chromium.org>
Change-Id: I479c8f80e45cc524ba87db4293d19b29bdfa2192
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57048
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Make neovim the default editor and create an alias for vim.
The NixOS module for neovim is currently broken. Thus, add a note to
`description.md` to switch to that later.
Change-Id: I9345a6e32f3035565e55e50579c97121b4987d83
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57393
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add a Nix shell file which provides an environment for compilation of
the coreboot toolchain. The Nix shell can be used by running the
following command:
$ nix-shell --pure util/nixshell/toolchain.nix
The `--pure` parameter is optional, but it makes sure that the
environment is as minimal as possible and does not contain any unrelated
or unneeded software or configuration.
Once compiled, the coreboot toolchain can be used without loading the
shell environment.
If `--pure` is used, SSL connections won't work since the
`SSL_CERT_FILE` environment variable is not configured, which makes the
build tool unable to download the source files. Thus, let it point to
the system certificate store.
Change-Id: I341ee28c5451d2c6cb4ff22de67161d99f4ca77a
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57646
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
|
|
This now skips all of the pieces done by PSP_verstage.
BUG=None
TEST=Boot Guybrush with & without PSP_verstage
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: I5a6b8e2284e232c30c9f36ea7c6ab044e2644f7b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57318
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Since the PCIE training for the USB WWAN card is no longer being run,
we can initialize the GPIOs the same for all WWAN cards.
BUG=b:193036827
TEST=Boot and reboot with fibocom FM350-GL & L850GL modules
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: Idc9a7cb883fc8dd6bbc6077b8ea99182f17f888b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57317
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Check to see if the PCIe slot needs to be activated for the WWAN card.
If it doesn't, leave it unused so it will be powered off and not do
the PCIe training.
BUG=b:193036827
TEST=Boot & Reboot guybrush with both PCIe & USB WWAN cards.
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: I79c32e4814672c03ee0821786d5be1c77fd1b410
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57316
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
ALC5682-VD/ALC5682-VS use different kernel driver by different hid name.
Update hid name depending on the AUDIO field of fw_config.
ALC5682-VD: _HID = "10EC5682"
ALC5682I-VS: _HID = "RTL5682"
BUG=b:200009010
TEST=ALC5682-VD/ALC5682-VS audio codec can work
Signed-off-by: Mark Hsieh <mark_hsieh@wistron.corp-partner.google.com>
Change-Id: I09c7830fff6b318cf1a1f4a44ee0a819691f7c58
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57673
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add MIPI camera support for OVTI2740
BUG=b:196937374 b:194926283
TEST=Build and boot on Kano
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: I248c64b9460c898f9faa5f7ac8cf339a9c814013
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57572
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
Report different ACPI device depending on TP_SOURCE field of fw config
(SSFC-bit8~bit9) for elan touchpad.
BUG=b:199503876
TEST=FW_NAME=redrix emerge-brya coreboot
Signed-off-by: Wisley Chen <wisley.chen@quanta.corp-partner.google.com>
Change-Id: I15781c2d942d81e11c296ea2f2586ba82f67e4a7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57575
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
This patch has changes to support multiple camera modules, base on the value set in the SSFC_CONFIG.
BUG=b:198235323
TEST=tested the changes with redrix 5MP(ov5675/hi556) camera.
Change-Id: I71c8355617171ec7d08862759b87d4bf12ce2924
Signed-off-by: Arec Kao <arec.kao@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57272
Reviewed-by: Andy Yeh <andy.yeh@intel.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The PCIe WWAN module used on brya0 requires control over 4 signals to
successfully power it on. It is desirable to do this before passing
control to the payload, because the modem requires a ~10 seconds
initialization phase before it can be used.
The corrected sequence looks like:
1) Drive device into full reset and enable power in bootblock
2) Deassert FCPO in romstage, after power rails stabilize
3) Deassert WLAN_RST#, then WLAN_PERST# in ramstage
BUG=b:187691798
Change-Id: I10f15a4dcfd86216c334fb24b4693ea250d35ee4
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/57540
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
|
