summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2021-09-30soc/intel/alderlake: Perform `soc_finalize` at entry of BS_PAYLOAD_BOOTSubrata Banik
This patch ensures soc_finalize() is getting called at the entry of BS_PAYLOAD_BOOT boot state instead of BS_PAYLOAD_LOAD, BS_ON_EXIT. The purpose of this change is to accommodate more time to push out sending CSE EOP messages at post. BUG=b:200644229 TEST=coreboot serial log suggests soc_finalize() is getting called as part of the BS_PAYLOAD_BOOT entry. Finalizing chipset. apm_control: Finalizing SMM. APMC done. BS: BS_PAYLOAD_BOOT entry times (exec / console): 21 / 15 ms Change-Id: I8632eca057255d7f4a38b64fd17c1f3d84123051 Signed-off-by: Subrata Banik <subrata.banik@intel.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/57801 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org> Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
2021-09-30soc/intel/common/../cse: Perform D0I3 bit reset/set prior sending EOPSubrata Banik
Prior to coreboot sending EOP messages during post, it's important to ensure that CSE is not in Idle state. In case CSE is in Dev Idle state (which means D0I3 bit is set), reset this bit before sending EOP command. This patch ensures coreboot has provision to send CSE EOP messages even after the FSP Notify phase without any delays waiting for the device to respond or timeout. BUG=b:200644229 TEST=Able to send CSE EOP message even after FSP Notify phase. Attempting CSE EOP msg sending post FSP notify without this code change causes `timeout` issue as below: BS: BS_PAYLOAD_LOAD exit times (exec / console): 171 / 0 ms Finalizing chipset. apm_control: Finalizing SMM. APMC done. HECI: Sending End-of-Post HECI: timed out reading answer! HECI: Failed to receive! HECI: receive Failed HECI: EOP send/receive fail ERROR: Failed to send EOP to CSE, 2 cse: CSE status registers: HFSTS1: 0x90000255, HFSTS2: 0xf10516 HFSTS3: 0x20 VB2:vb2api_fail() Need recovery, reason: 0x31 / 0xc Saving nvdata board_reset() called! full_reset() called! Attempting CSE EOP msg sending post FSP notify with this code change is `successful` as below: BS: BS_PAYLOAD_LOAD exit times (exec / console): 170 / 0 ms Finalizing chipset. apm_control: Finalizing SMM. APMC done. HECI: Sending End-of-Post CSE: EOP requested action: continue boot CSE EOP successful, continuing boot Change-Id: Iae1bc52e94b08f97004424ea0c147d6da8aca6e2 Signed-off-by: Subrata Banik <subrata.banik@intel.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/57805 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com> Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
2021-09-30soc/intel/common/../cse: Create APIs for CSE device state transitionSubrata Banik
This patch ensures APIs that are responsible for CSE device state transition between active to idle and vice-versa are available publically for other modules/boot stages to consume. BUG=b:200644229 TEST=Able to build and boot ADLRVP-P. Change-Id: Ia480877822d343f2b4c9bf87b246812186d49ea3 Signed-off-by: Subrata Banik <subrata.banik@intel.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/57804 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org> Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com> Reviewed-by: Angel Pons <th3fanbus@gmail.com>
2021-09-30mb/intel/adlrvp: Update Rcomp target value for DDR4 RVP SKUSubrata Banik
Update to recommended Rcomp drive strength value for DDR4 as per MRC team's input. Additionally, add space around the `targets` array. Change-Id: Ied63913db94b2e52ab394a66c70f7edfd507d99a Signed-off-by: Subrata Banik <subrata.banik@intel.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/58036 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Angel Pons <th3fanbus@gmail.com> Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
2021-09-30mb/google/brya/variants/gimble: Correct SSD power sequenceMark Hsieh
M.2 spec describes PERST# should be sequenced after power enable. BUG=b:201512872 TEST=USE="project_gimble emerge-brya coreboot" and verify it builds without error. Signed-off-by: Mark Hsieh <mark_hsieh@wistron.corp-partner.google.com> Change-Id: Ie164ddb29f947e190fa87b31165e3c84b07926e3 Reviewed-on: https://review.coreboot.org/c/coreboot/+/58034 Reviewed-by: Zhuohao Lee <zhuohao@google.com> Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2021-09-29soc/intel/cannonlake: Guard acpi_fill_ssdt assignment with HAVE_ACPI_TABLESTim Wawrzynczak
Change-Id: I3677b4e545599d00a4ba16464836834febc2d1a5 Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org> Reviewed-on: https://review.coreboot.org/c/coreboot/+/58024 Reviewed-by: Michael Niewöhner <foss@mniewoehner.de> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2021-09-29soc/intel: Drop unnecessary `select REG_SCRIPT`Angel Pons
These platforms no longer use reg-script. Drop unneeded select. Change-Id: I8fc4dc29d25dffbf9ed1947d0ff013b2fae0faaf Signed-off-by: Angel Pons <th3fanbus@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/58007 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Arthur Heymans <arthur@aheymans.xyz> Reviewed-by: Michael Niewöhner <foss@mniewoehner.de> Reviewed-by: Felix Singer <felixsinger@posteo.net> Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
2021-09-29soc/intel/common/block/smbus: Drop reg-script usageAngel Pons
Using reg-script just to read-modify-write some registers makes no sense. Replace reg-script usage with regular register operations. Change-Id: I87d1278360a231cbe5b5f825ad9a448e59e63ea2 Signed-off-by: Angel Pons <th3fanbus@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/58006 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Arthur Heymans <arthur@aheymans.xyz> Reviewed-by: Michael Niewöhner <foss@mniewoehner.de> Reviewed-by: Felix Singer <felixsinger@posteo.net> Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
2021-09-29soc/intel/skylake: Drop reg-script usageAngel Pons
Using reg-script just to read-modify-write some registers makes no sense. Replace reg-script usage with regular register operations. Change-Id: Ib3c83131c30fd02c579b910cfad6843eb28ba8f1 Signed-off-by: Angel Pons <th3fanbus@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/58005 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Arthur Heymans <arthur@aheymans.xyz> Reviewed-by: Michael Niewöhner <foss@mniewoehner.de> Reviewed-by: Felix Singer <felixsinger@posteo.net> Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
2021-09-29soc/intel/{cnl,jsl,tgl,ehl,adl}: rename PMC device init/enable callbacksMichael Niewöhner
The current names of the PMC init/enable callbacks are very confusing. Rename them. Change-Id: I69f54f3b4e1ea9a9b4fa5c8dd9c0d454d7cd1283 Signed-off-by: Michael Niewöhner <foss@mniewoehner.de> Reviewed-on: https://review.coreboot.org/c/coreboot/+/57995 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org> Reviewed-by: Felix Singer <felixsinger@posteo.net> Reviewed-by: Angel Pons <th3fanbus@gmail.com>
2021-09-29google/trogdor: Always initialize eDP bridge I2C QUP firmwareJulius Werner
In CB:52662 when MIPI display support was added, we accidentally changed the code flow for eDP displays such that i2c_init() will no longer be called when display_init_required() is false. This is a problem because on this platform, i2c_init() does not just prepare the I2C controller for firmware use, it also loads firmware to the controller that makes it behave like an I2C device in the first place -- a step that the kernel cannot later do on its own if the firmware didn't already do it. Skipping this initialization means the I2C controller becomes unusable to the kernel. This patch fixes the issue by making the i2c_init() unconditional again. Signed-off-by: Julius Werner <jwerner@chromium.org> Change-Id: Ie4546c31d87d91113eeef7dc7a18599a87e6d6eb Reviewed-on: https://review.coreboot.org/c/coreboot/+/58026 Reviewed-by: Douglas Anderson <dianders@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2021-09-29soc/intel: Rename GNVS struct member to match ASLAngel Pons
Rename the `ecps` GNVS struct member to `epcs` to match the name in ASL. Change-Id: I1f6b97309eea75e7dbb4e5e664660df05ec0845e Signed-off-by: Angel Pons <th3fanbus@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/57979 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
2021-09-29herobrine: Initialize SAR sensor QUPShelley Chen
Initializing SAR sensor (QUP2, address 0x988000) BUG=b:198456205 BRANCH=None TEST=Boot into kernel and make sure no i2c errors for 0x988000 in dmesg Change-Id: I75b0e9173d4c49b5e7308158a678964d6637b225 Signed-off-by: Shelley Chen <shchen@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/58023 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Julius Werner <jwerner@chromium.org>
2021-09-29mb/google/herobrine: Change preprocessor to C codeShelley Chen
BUG=b:182963902 BRANCH=None TEST=./util/abuild/abuild -p none -t GOOGLE_HEROBRINE -x -a -c max -B Change-Id: I10f8a9682200b883474dc385331c5dae84cbdb08 Signed-off-by: Shelley Chen <shchen@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/58022 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Julius Werner <jwerner@chromium.org>
2021-09-29herobrine: Add fingerprint power sequencingShelley Chen
For Herobrine variants that include a finger print sensor, we will need to power sequence it. We are using the same FP sensor as trogdor, so we will follow the timings used for trogdor from CL:2695676. BUG=b:198474942 BRANCH=None TEST=./util/abuild/abuild -p none -t GOOGLE_HEROBRINE -x -a -c max -B Change-Id: Ica6eafc47cf1b95eeb8d94c6e0a8c88519665e3f Signed-off-by: Shelley Chen <shchen@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/58021 Reviewed-by: Alexandru Stan <amstan@chromium.org> Reviewed-by: Julius Werner <jwerner@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2021-09-29mb/google/guybrush/var/nipperkin: Add ALC5682I and MAX98360 supportPatrick Huang
Add ID "10029836" for machine driver, "RTL5682" for ALC5682I and "MX98357A" for MAX98360. BUG=b:198716348 TEST=Build nipperkin, codec is functional with new machine driver. Signed-off-by: Patrick Huang <patrick.huang@amd.corp-partner.google.com> Change-Id: Iab9d11adb7cd08effa2a9b6a627832bd89cb3cb5 Reviewed-on: https://review.coreboot.org/c/coreboot/+/57611 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
2021-09-29Update vboot submodule to upstream main (13f601f)Selma Bensaid
Updating from commit id c5a482ed: 2021-09-08 17:16:59 +0000 - (sign_official_build: disable gsetup for reven) to commit id 13f601f: 13f601f vboot: boot from miniOS recovery kernels on disk b This brings in 14 new commits. Signed-off-by: Selma Bensaid <selma.bensaid@intel.com> Change-Id: I66788ea434a6000435b97ce64107f3b5da882414 Reviewed-on: https://review.coreboot.org/c/coreboot/+/57994 Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2021-09-29mb/google/dedede/var/boten: Add fw_config probe for ALC5682-VD & VSStanley Wu
ALC5682-VD/ALC5682I-VS load different kernel driver by different hid name. Update hid name depending on the AUDIO_CODEC_SOURCE field of fw_config. Define SSFC bit 9-11 in coreboot for codec within ec. ALC5682-VD: _HID = "10EC5682" ALC5682I-VS: _HID = "RTL5682" BUG=b:193694180 TEST=ALC5682-VD/ALC5682I-VS audio codec can work Signed-off-by: Stanley Wu <stanley1.wu@lcfc.corp-partner.google.com> Change-Id: Iba91b51cbbe7adc502372c9a026867de61d8035d Reviewed-on: https://review.coreboot.org/c/coreboot/+/57977 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Paul Menzel <paulepanter@mailbox.org> Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
2021-09-29mb/google/mancomb: Delete board supportKarthikeyan Ramasubramanian
Mancomb mainboard has been cancelled. Hence delete the board support. BUG=b:190404616 TEST=None Cq-Depend: chromium:3188634 Change-Id: I3ce02efb1fa5ea488447099abe08da6051fb6fc6 Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/57996 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Rob Barnes <robbarnes@google.com> Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
2021-09-29arch/x86,cpu/x86: Disable the %gs and %fs segmentsRaul E Rangel
The %fs and %gs segment are typically used to implement thread local storage or cpu local storage. We don't currently use these in coreboot, so there is no reason to map them. By setting the segment index to 0, it disables the segment. If an instruction tries to read from one of these segments an exception will be raised. The end goal is to make cpu_info() use the %gs segment. This will remove the stack alignment requirements and fix smm_do_relocation. BUG=b:194391185, b:179699789 TEST=Boot guybrush to OS Signed-off-by: Raul E Rangel <rrangel@chromium.org> Change-Id: Iaa376e562acc6bd1dfffb7a23bdec82aa474c1d5 Reviewed-on: https://review.coreboot.org/c/coreboot/+/57860 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Eric Peers <epeers@google.com> Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
2021-09-29soc/intel/alderlake: Add GFx Device ID 0x46c3Selma Bensaid
This CL adds support for new ADL-M graphics Device ID 0x46c3. TEST=boot to OS Change-Id: Ib55fb501f96fe9bcc328202511bbfe84a3122285 Signed-off-by: Selma Bensaid <selma.bensaid@intel.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/57993 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
2021-09-29mb/intel/adlrvp, mb/google/brya: Add ADLP 242 PLx configurationsTracy Wu
Add ADLP 242 sku PLx related settings, which follow the settings of ADLP 282 sku (both are 15w). BUG=b:201253904 TEST=USE='fw_debug' emerge-brya intel-adlfsp coreboot chromeos-bootimage Change-Id: If9b60893ab3e2c4a88e7d2cf45223c5fbce6f847 Signed-off-by: Tracy Wu <tracy.wu@intel.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/57992 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
2021-09-29soc/intel/alderlake: Add ADLP 242 power configurationsTracy Wu
Add ADLP 242 sku power related settings, which follow the settings of ADLP 282 sku (both are 15w). BUG=b:201253904 TEST=Build and check fsp log to confirm the settings are set properly. Change-Id: I829dd690c22d167a507b1910106da06b275cec09 Signed-off-by: Tracy Wu <tracy.wu@intel.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/57991 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
2021-09-29mb/google/brya: Update PCH power cycle related durationsTim Wawrzynczak
The voltage rail discharge times have been measured, so therefore the boot time on a cold boot when the CSE must go through a global reset and thus a trip to S5 can be optimized. Select the lowest applicable value for each PchPmSlp UPD that can be used with these measurements. This is programmed in the baseboard because the measured discharge times leave (what should be) plenty of margin for variants to also not violate any power sequencing guidelines from the PDG. BUG=b:184799383 TEST=verified time in S5 during a global reset is ~1s instead of 4s Change-Id: Ia373c47b3967d68ddac21707c6eb4565d9d6519e Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org> Reviewed-on: https://review.coreboot.org/c/coreboot/+/57892 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com> Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
2021-09-29soc/intel/alderlake: Add support for power cycle and SLP signal durationTim Wawrzynczak
The UPDs for PM power cycle duration and SLP_* signal durations are all identical to Tiger Lake, so add similar support, but use enums instead of comments to represent the durations symbolically. BUG=b:184799383 Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org> Change-Id: I4a531f042658894bcbc6a76eff453c06e90d66b0 Reviewed-on: https://review.coreboot.org/c/coreboot/+/57891 Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2021-09-29mb/google/dedede: Remove drawcia_legacy board supportKarthikeyan Ramasubramanian
Support for drawcia_legacy board is cancelled. Hence remove the board support. BUG=b:192256341 TEST=None Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com> Change-Id: I76cd3e388439f5aee94a17fe35ae210f449cfbfc Reviewed-on: https://review.coreboot.org/c/coreboot/+/58000 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Evan Green <evgreen@chromium.org>
2021-09-29mb/google/dedede: Remove Boten_Legacy board supportKarthikeyan Ramasubramanian
Support for Boten_legacy board is cancelled. Hence remove the board support. BUG=b:192256341 TEST=None Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com> Change-Id: If26dc869ff95dff70c0f83a13f6f727aa5992dbd Reviewed-on: https://review.coreboot.org/c/coreboot/+/57999 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Evan Green <evgreen@chromium.org>
2021-09-29mb/google/dedede: Remove wheelie variant board supportKarthikeyan Ramasubramanian
Wheelie variant board has been cancelled. Remove wheelie variant board support. BUG=b:192256341 TEST=None Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com> Change-Id: I3ad5bc1c987feb55183a663937794781c7301a48 Reviewed-on: https://review.coreboot.org/c/coreboot/+/57998 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Evan Green <evgreen@chromium.org>
2021-09-29mb/google/dedede: Remove cappy variant supportKarthikeyan Ramasubramanian
Cappy variant is cancelled. Hence delete the cappy variant support. BUG=b:192256341 TEST=None Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com> Change-Id: If43188a3e6bf4f4449c7e2d08be7609efe58dca1 Reviewed-on: https://review.coreboot.org/c/coreboot/+/57997 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Evan Green <evgreen@chromium.org>
2021-09-29{sb,soc}/intel: Drop unused globalnvs.asl methodsAngel Pons
These methods are never used in the code. Drop them. Change-Id: If5568b494f821d2647ada5ae845bcd015708520e Signed-off-by: Angel Pons <th3fanbus@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/57984 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
2021-09-29{sb,soc}/intel: Drop PRMx from GNVSAngel Pons
These fields are never used in the code. Drop them. Change-Id: Icd07f2d704c19126bf6df4d740c21d5a1342061b Signed-off-by: Angel Pons <th3fanbus@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/57983 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
2021-09-29{sb,soc}/intel: Drop LCKF from GNVSAngel Pons
This field is never used in the code. Drop it. Change-Id: I88207ec369ab83823ef2f3fc40f68a0980ce9663 Signed-off-by: Angel Pons <th3fanbus@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/57982 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
2021-09-29soc/mediatek/mt8195: initialize DFDRex-BC Chen
DFD (Design for Debug) is a debugging tool, which scans flip-flops and dumps to internal RAM on the WDT reset. After system reboots, those values could be showed for debugging. BUG=b:192429713 Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com> Change-Id: Ied63913db94b2e52ab394a66c70f7edfd507c99b Reviewed-on: https://review.coreboot.org/c/coreboot/+/57980 Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.corp-partner.google.com> Reviewed-by: Hung-Te Lin <hungte@chromium.org> Reviewed-by: Yu-Ping Wu <yupingso@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2021-09-29vc/mediatek/mt8195: Remove unused codeRyan Chuang
Remove unused drivers and some fast calibration implementations to align with the latest MTK memory reference code. TEST=boot to kernel Signed-off-by: Ryan Chuang <ryan.chuang@mediatek.corp-partner.google.com> Change-Id: I2e6be2e16c139e48c65352fe2eabf16bf9cd550a Reviewed-on: https://review.coreboot.org/c/coreboot/+/57978 Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.corp-partner.google.com> Reviewed-by: Hung-Te Lin <hungte@chromium.org> Reviewed-by: Yu-Ping Wu <yupingso@google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2021-09-28mb/purism/librem_skl: Clean up dsdt.aslFelix Singer
Move includes using library paths to the top and remove unnecessary comments. Also, get rid of that unnecessary _SB scope. Use an absolute path for the PCI0 device instead. Change-Id: I2c4fb1933eda2eb75bfe9181f13e189ec66cadf9 Signed-off-by: Felix Singer <felixsinger@posteo.net> Reviewed-on: https://review.coreboot.org/c/coreboot/+/57849 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Angel Pons <th3fanbus@gmail.com> Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
2021-09-28mb/google/brya/variants/taeko: add NVMe GPIOs to early_gpio_tableKevin Chang
NVMe needs extra time to run boot process, enable power and deassert reset for NVMe earlier in the boot flow that taeko can successfully boot into OS with non-serial coreboot. BUG=b:199969366 & b:200711149 TEST=Build FW and test with non-serial FW reboot 20 times pass. Signed-off-by: Kevin Chang <kevin.chang@lcfc.corp-partner.google.com> Change-Id: I032c5b90fb2148c4075d6ead3e4161c0cc659b20 Reviewed-on: https://review.coreboot.org/c/coreboot/+/57659 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
2021-09-28mb/google/dedede/var/magolor: Add custom Wifi SAR for magmaTyler Wang
Add wifi sar for magma. Due to fw-config cannot distinguish between magolor and magma. Using sku_id to decide to load magma custom wifi sar. BUG=b:192423859 TEST= emerge-dedede coreboot Signed-off-by: Tyler Wang <tyler.wang@quanta.corp-partner.google.com> Change-Id: Iac15e958e61be6e3c136fb9be18b4695823ad1c9 Reviewed-on: https://review.coreboot.org/c/coreboot/+/57690 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org> Reviewed-by: Henry Sun <henrysun@google.com> Reviewed-by: David Wu <david_wu@quanta.corp-partner.google.com> Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
2021-09-28arch/x86: Make sure compiler knows we're stopping in hlt()Martin Roth
Currently, static analyzers don't recognize that hlt() doesn't return, so they show errors like uninitialized variables assuming that it does return. This takes care of that problem. Signed-off-by: Martin Roth <martin@coreboot.org> Change-Id: Ia2325700b10fe1f89d749edfe5aee72b47d02f2e Reviewed-on: https://review.coreboot.org/c/coreboot/+/56978 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
2021-09-28mb/google/dedede/var/galtic: Update PL1 min and max for Galith/GallopFrankChu
Update PL1 min and max values to 6 W for Galith/Gallop systems. BUG=b:201010771 BRANCH=None TEST=Build and verify on Galith/Gallop system Signed-off-by: FrankChu <frank_chu@pegatron.corp-partner.google.com> Change-Id: I0dfda3c2c830a2ce203668431f396859e782aa3c Reviewed-on: https://review.coreboot.org/c/coreboot/+/57654 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
2021-09-28vendorcode/intel/fsp: Add Alder Lake FSP headers for FSP v2374_01Ronak Kanabar
The headers added are generated as per FSP v2374_01. Previous FSP version was v2347_00. Changes Include: - Offset change in FspmUpd.h and FspsUpd.h BUG=b:201239436 BRANCH=None TEST=Build and boot brya Cq-Depend: chrome-internal:4150766 Change-Id: I097e854bcb4033bdaf2498fb97b255e87d3dd70f Signed-off-by: Ronak Kanabar <ronak.kanabar@intel.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/57920 Reviewed-by: Nick Vaccaro <nvaccaro@google.com> Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2021-09-28mb/google/brya/primus: modify HID to MX98360A for next build phaseMalik_Hsu
For the next build phase, modify the HID of the speaker amp to MX98360A. BUG=b:199098681 BRANCH=none TEST=build coreboot without error Signed-off-by: Malik_Hsu <malik_hsu@wistron.corp-partner.google.com> Change-Id: I0c318464fca7d35bbffd7ea0f5694b83acedff0e Reviewed-on: https://review.coreboot.org/c/coreboot/+/57434 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Zhuohao Lee <zhuohao@google.com> Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
2021-09-28soc/intel/baytrail: Always handle MRC as ELF fileAngel Pons
The current MRC binaries for Bay Trail are always ELF files. Always adjust the position in CBFS using the ELF header regardless of file names. Without adjusting the position, the system hangs right after calling into MRC. TEST: MRC position in CBFS does not change for bostentech/gbyt4. Change-Id: I74e1246a5fac3f3649be9842ff13c2fc70f72a20 Signed-off-by: Angel Pons <th3fanbus@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/57989 Reviewed-by: Arthur Heymans <arthur@aheymans.xyz> Reviewed-by: Michael Niewöhner <foss@mniewoehner.de> Reviewed-by: Matt DeVillier <matt.devillier@gmail.com> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2021-09-28mb/google/dedede/var/kracko: refactor DPTF section for overridesRobert Chen
Refactor DPTF section of code under the kracko overridetree. This makes kracko override dptf section of dedede/baseboard, because the DPTF tool's CRT, PSV and TSR3 settings are different than expected. BUG=b:187482019 BRANCH=dedede TEST=Built and tested on dedede system Change-Id: Iacc543f961a7f4652ee8583920b1794f916c7ec9 Signed-off-by: Robert Chen <robert.chen@quanta.corp-partner.google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/57828 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
2021-09-27soc/qualcomm/sc7280: Enable QUP drivers to use lz4 compressionShelley Chen
BUG=b:182963902 BRANCH=None TEST=./util/abuild/abuild -p none -t GOOGLE_HEROBRINE -x -a -B Change-Id: I3ec557bdf2286c3f60902d5ac018b536fe99afa3 Signed-off-by: Shelley Chen <shchen@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/57896 Reviewed-by: Julius Werner <jwerner@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2021-09-27soc/intel/baytrail: Drop invalid `VGA_BIOS_FILE` defaultAngel Pons
This file does not exist in the coreboot tree. One should place this file in the `site-local` subdirectory and specify the paths by means of `site-local/Kconfig`. Change-Id: I86ac2a6176947f12194bec6b63bedd7db79820a0 Signed-off-by: Angel Pons <th3fanbus@gmail.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/54761 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
2021-09-27ec/purism: Remove copied code from system76Arthur Heymans
This code is identical except for some renaming. Change-Id: I93795a6087ce0daca27c0d5038a1febd6ca9c775 Signed-off-by: Arthur Heymans <arthur@aheymans.xyz> Reviewed-on: https://review.coreboot.org/c/coreboot/+/56522 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
2021-09-27arch/x86,cpu/x86: Move cpu_info initialization instructions into macroRaul E Rangel
This will help reduce duplication and make it easier to add new members to the cpu_info struct. BUG=b:194391185, b:179699789 TEST=Compare assembly of romstage and ramstage before and after Signed-off-by: Raul E Rangel <rrangel@chromium.org> Change-Id: I31f264f4bb8b605fa3cb3bfff0d9bf79224072aa Reviewed-on: https://review.coreboot.org/c/coreboot/+/57859 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
2021-09-27soc/amd/cezanne/early_fch: move mb_set_up_early_espi into if blockFelix Held
mb_set_up_early_espi should only be called when SOC_AMD_COMMON_BLOCK_USE_ESPI is selected. TEST=None Signed-off-by: Felix Held <felix-coreboot@felixheld.de> Change-Id: Ic8ad724a2a79c1995fbe9d97f11a0f69eed9435c Reviewed-on: https://review.coreboot.org/c/coreboot/+/57781 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Martin Roth <martinroth@google.com>
2021-09-27soc/amd/cezanne: Enable CCP DMAKarthikeyan Ramasubramanian
Enable CCP DMA use in PSP verstage. This helps to reduce the boot time. BUG=b:194990811 TEST=Build and boot to OS in Guybrush. Observed a 35 - 40 ms improvement in the boot time. Before CCP DMA: 508:finished loading body 898,286 (287,576) Total Time: 2,146,182 After CCP DMA: 508:finished loading body 853,627 (240,061) Total Time: 2,110,117 Cq-Depend: chrome-internal:4116566 Change-Id: I6e4f081622a2ec78763adf56548204efc1bccf39 Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/57564 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Raul Rangel <rrangel@chromium.org>
2021-09-27soc/amd/common/psp_verstage: Introduce boot device driverKarthikeyan Ramasubramanian
PSP verstage can access the boot device either in Programmed I/O mode or DMA mode. Introduce a boot device driver and use the appropriate mode based on the SoC support. BUG=b:194990811 TEST=Build and boot to OS in Guybrush. Change-Id: I8ca5290156199548916852e48f4e11de7cb886fb Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/57563 Reviewed-by: Raul Rangel <rrangel@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2021-09-27mb/google/brya/var/kano: Move max98373 amp ACPI info to I2C0David Wu
Move max98373 amp ACPI info to I2C0 according to kano's schematics version KANO_MLB_Proto_0811. BUG=b:192370253 TEST=FW_NAME=kano emerge-brya coreboot chromeos-bootimage Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com> Change-Id: I8f7a7938dd407666e0104ba64b22da85216a145f Reviewed-on: https://review.coreboot.org/c/coreboot/+/57909 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
2021-09-27mb/google/brya: Correct SSD power sequenceEric Lai
SSD sometimes can't be detected in in warm/cold boot stress. M.2 spec describes SSD_PREST should be sequenced after power enable. BUG=b:199822704 TEST=SSD was always discovered in warm/cold boot stress. Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com> Change-Id: If0a9e36cda4dc91bbccec02f39ccb9b658d24056 Reviewed-on: https://review.coreboot.org/c/coreboot/+/57665 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
2021-09-27soc/amd/cezanne, vc/amd/fsp/*: Add support for CCP DMA SVC callKarthikeyan Ramasubramanian
Add support to access the boot device from PSP through Crypto Co-Processor (CCP) DMA. Implement a SVC call to use CCP DMA on SoCs where it is supported and a stub on SoCs where it is not supported. This provides an improved performance while accessing the boot device and reduces the boot time by ~45 ms. BUG=b:194990811 TEST=Build and boot to OS in guybrush. Perform cold and warm reboot cycling for 250 iterations. Change-Id: I02b94a842190ac4dcf45ff2d846b8665f06a9c75 Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/57562 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Raul Rangel <rrangel@chromium.org>
2021-09-27mb/google/hatch/moonbuggy: Update DPTF parametersKenneth Chan
Update the DPTF parameters received from the thermal team. BUG=b:188596619 TEST=emerge-ambassador coreboot Signed-off-by: Kenneth Chan <kenneth.chan@quanta.corp-partner.google.com> Change-Id: I081963b97ed2dae0f5d026f6443c954b52347a8a Reviewed-on: https://review.coreboot.org/c/coreboot/+/57919 Reviewed-by: Joe Tessler <jrt@google.com> Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org> Reviewed-by: Paul Menzel <paulepanter@mailbox.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2021-09-27mb/system76/gaze15: Disable OC supportTim Crawford
Clevo indicated that DIMMs running at 2933 MHz are not supported on a number of processors used for this model. Change-Id: Iadf611a64de664c783696e51cfe858ca95903936 Signed-off-by: Tim Crawford <tcrawford@system76.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/57897 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Jeremy Soller <jeremy@system76.com>
2021-09-27mb/system76/lemp10: Use PME virtual wire for SWITim Crawford
Match the behavior of the other TGL-U boards. Change-Id: Ida962255f7a2435319d739d59eb2dc58fe342ae8 Signed-off-by: Tim Crawford <tcrawford@system76.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/57895 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Jeremy Soller <jeremy@system76.com>
2021-09-27mb/system76: rtd3: Remove SrcClk pin on CPU RPTim Crawford
Setting srcclk_pin only works for PCH PCIe devices. Disable them on the CPU RP and add a TODO. Change-Id: I32db116feb33a8448eb8586fe9e882b8879489d4 Signed-off-by: Tim Crawford <tcrawford@system76.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/57882 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Jeremy Soller <jeremy@system76.com>
2021-09-27mb/intel/kblrvp: Clean up dsdt.aslFelix Singer
Move includes using library paths to the top and remove unnecessary comments. Also, get rid of that unnecessary _SB scope. Use an absolute path for the PCI0 device instead. Change-Id: Ibb63f3ecd9cfbb6f564e0a9968c2776c25d84f79 Signed-off-by: Felix Singer <felixsinger@posteo.net> Reviewed-on: https://review.coreboot.org/c/coreboot/+/57856 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Angel Pons <th3fanbus@gmail.com>
2021-09-27mb/51nb/x210: Clean up dsdt.aslFelix Singer
Move includes using library paths to the top and remove unnecessary comments. Also, get rid of that unnecessary _SB scope. Use an absolute path for the PCI0 device instead. Change-Id: I7255ac1ec6c43dd4b21325ae60e117458bea956d Signed-off-by: Felix Singer <felixsinger@posteo.net> Reviewed-on: https://review.coreboot.org/c/coreboot/+/57855 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Angel Pons <th3fanbus@gmail.com>
2021-09-27mb/razor/blade_stealth_kbl: Clean up dsdt.aslFelix Singer
Move includes using library paths to the top and remove unnecessary comments. Also, get rid of that unnecessary _SB scope. Use an absolute path for the PCI0 device instead. Change-Id: I375ab879dd95d6a7a20644dc36312a1e62f58226 Signed-off-by: Felix Singer <felixsinger@posteo.net> Reviewed-on: https://review.coreboot.org/c/coreboot/+/57854 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Angel Pons <th3fanbus@gmail.com>
2021-09-27mb/facebook/monolith: Clean up dsdt.aslFelix Singer
Move includes using library paths to the top and remove unnecessary comments. Change-Id: I4e5be60d2784d003a388c52254514d0ab4d002b0 Signed-off-by: Felix Singer <felixsinger@posteo.net> Reviewed-on: https://review.coreboot.org/c/coreboot/+/57853 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Angel Pons <th3fanbus@gmail.com> Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
2021-09-27mb/google/glados: Clean up dsdt.aslFelix Singer
Move includes using library paths to the top and remove unnecessary comments. Change-Id: Id26d9dfc3822b9120360fc2cb2ced8d67345a659 Signed-off-by: Felix Singer <felixsinger@posteo.net> Reviewed-on: https://review.coreboot.org/c/coreboot/+/57852 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Angel Pons <th3fanbus@gmail.com>
2021-09-27mb/intel/kunimitsu: Clean up dsdt.aslFelix Singer
Move includes using library paths to the top and remove unnecessary comments. Change-Id: I42458f16a323d3e37d0ee1bd8335e1f8d0e1fadc Signed-off-by: Felix Singer <felixsinger@posteo.net> Reviewed-on: https://review.coreboot.org/c/coreboot/+/57851 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Angel Pons <th3fanbus@gmail.com>
2021-09-27mb/intel/saddlebrook: Clean up dsdt.aslFelix Singer
Move includes using library paths to the top and remove unnecessary comments. Also, get rid of that unnecessary _SB scope. Use an absolute path for the PCI0 device instead. Change-Id: I730cd3eeffff60b3b569bfb748febbdc8ca85990 Signed-off-by: Felix Singer <felixsinger@posteo.net> Reviewed-on: https://review.coreboot.org/c/coreboot/+/57850 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Angel Pons <th3fanbus@gmail.com>
2021-09-27mb/google/dedede/var/blipper: Generate SPD ID for supported partsZhi Li
Add the relevant memory configuration of beetley to the blipper coreboot code The memory parts being added are: 1. Micron MT53E512M32D1NP-046 WT:B 2. Samsung K4U6E3S4AB-MGCL 3. Hynix H54G46CYRBX267 BUG=b:200000608 TEST=emerge-dedede coreboot Signed-off-by: Zhi Li <lizhi7@huaqin.corp-partner.google.com> Change-Id: I0b04f64cb007a58ae98f5ed187feb4859a43b1b6 Reviewed-on: https://review.coreboot.org/c/coreboot/+/57670 Reviewed-by: Weimin Wu <wuweimin@huaqin.corp-partner.google.com> Reviewed-by: Karthik Ramasubramanian <kramasub@google.com> Reviewed-by: Paul Menzel <paulepanter@mailbox.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2021-09-27soc/amd/common/block/include/acpimmio_map: add AOAC acronym in commentFelix Held
The Always On Always Connected block is referenced as AOAC in the code, so add that acronym in the comment and change the "Connect" to "Connected". Signed-off-by: Felix Held <felix-coreboot@felixheld.de> Change-Id: I6a23e0ccff62c6ceddae70e1bef5c5abf872c495 Reviewed-on: https://review.coreboot.org/c/coreboot/+/57926 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Raul Rangel <rrangel@chromium.org>
2021-09-27cpu/x86/mp_init: add expansion for SIPI acronymFelix Held
Signed-off-by: Felix Held <felix-coreboot@felixheld.de> Change-Id: Ic182d7c551932ab6917a81568490ed18acdcd597 Reviewed-on: https://review.coreboot.org/c/coreboot/+/57927 Reviewed-by: Raul Rangel <rrangel@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2021-09-26Revert "Revert "util/abuild: Regenerate xcompile on every abuild run""Reka Norman
This reverts commit d94f8bbe9da290e120df20bf244920436e9510e7. This is a reland of https://review.coreboot.org/57651. The original change broke parallel abuild runs since the xcompile file was deleted by every recursive call to abuild. This issue was fixed by rebasing on top of a change which only regenerates the xcompile on non-recursive calls. BUG=None TEST=Parallel abuild run succeeds. Change-Id: I086ba7b2ae1b8b14459838bd18ce962a84aa306d Signed-off-by: Reka Norman <rekanorman@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/57913 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org> Reviewed-by: Patrick Georgi <pgeorgi@google.com> Reviewed-by: Nico Huber <nico.h@gmx.de>
2021-09-25soc/intel/alderlake: Use intel_microcode_find() to locate ucode.binSubrata Banik
`intel_microcode_find()` function uses cached ucode data hence it would avoid locating ucode.bin from CBFS while passing ucode.bin pointer to FSP. Change-Id: I8f92c9f20dfb055c19c6996e601c8c24767aecb7 Signed-off-by: Subrata Banik <subrata.banik@intel.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/57831 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
2021-09-24mb/google/guybrush: Remove ALS presentationGwendal Grignou
guybrush does not have a light sensor, do not include ACPI0008 ACPI device (Light sensor that will be managed by acpi-als IIO kernel driver). BUG=b:200823325 TEST=Check on Guybrush360 the sensor is not presented. Signed-off-by: Gwendal Grignou <gwendal@chromium.org> Change-Id: Id1dcb3a01ee43f780e4b118d88a0351e4c543f5a Signed-off-by: Gwendal Grignou <gwendal@chromium.org> Reviewed-on: https://review.coreboot.org/c/coreboot/+/57847 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Rob Barnes <robbarnes@google.com>
2021-09-24mb/google/brya/variants/primus: config dram speed to 3733Casper Chang
This change config the DRAM speed to 3733 for primus. BUG=b:200752480 BRANCH=none TEST=Verified that `dmidecode -t17` shows the correct configured memory speed Signed-off-by: Casper Chang <casper_chang@wistron.corp-partner.google.com> Change-Id: I2f3a9489dddcf102b0ffc71eb9cdab6ad38d1391 Reviewed-on: https://review.coreboot.org/c/coreboot/+/57867 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
2021-09-24mb/intel/adlrvp: Switch to using device pointersFurquan Shaikh
This change replaces the device tree walks with device pointers by using alias for dptf_policy device. Change-Id: I02ca63ac2cc1b8ed2f5a381b3824c9beff7f33ec Signed-off-by: Furquan Shaikh <furquan@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/57870 Reviewed-by: Subrata Banik <subrata.banik@intel.com> Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2021-09-24soc/intel/alderlake: Switch to using device pointersFurquan Shaikh
This change replaces the device tree walks with device pointers by using alias for tcss_usb3_port* devices. Change-Id: I65d9c83a9d0aab5a42f5a7cc6df98a154e79d16a Signed-off-by: Furquan Shaikh <furquan@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/57848 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Karthik Ramasubramanian <kramasub@google.com> Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
2021-09-24device: Drop unused function `dev_find_matching_device_on_bus`Furquan Shaikh
With use of device pointers, `dev_find_matching_device_on_bus()` is now unused and hence this change drops the function. Change-Id: I30fcb2d9932d770ca614cceffb15646ce8256465 Signed-off-by: Furquan Shaikh <furquan@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/57846 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Karthik Ramasubramanian <kramasub@google.com> Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
2021-09-24mb/google/zork: Switch to using device pointersFurquan Shaikh
This change replaces the device tree walks with device pointers by using alias for following devices: 1. audio_rt5682 2. xhci0_bt 3. xhci1_bt 4. acp_machine 5. i2c2 Change-Id: I56921ab54716e4d771d9de1a479f191ca5657eba Signed-off-by: Furquan Shaikh <furquan@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/57845 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Karthik Ramasubramanian <kramasub@google.com> Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
2021-09-24mb/google/guybrush: Configure the level for AMD Firmware binariesKarthikeyan Ramasubramanian
AMD Firmware tool allows configuring the directory table level in which the binaries have to be added. This helps to achieve space and boot time savings. BUG=b:195329409 TEST=Build and boot to OS in Guybrush. Achieve a boot time savings of ~75 ms and space savings of ~600 KB per RW section. Change-Id: Idc212b8c4f8aacfb0132983a8055f1e97af42983 Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/57814 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Bao Zheng <fishbaozi@gmail.com> Reviewed-by: Rob Barnes <robbarnes@google.com> Reviewed-by: Raul Rangel <rrangel@chromium.org>
2021-09-24mb/google/brya/var/taeko: Enable SaGv supportJoey Peng
Enable SaGv support for taeko BUG=b:198548214 TEST=FW_NAME=taeko emerge-brya coreboot Flash fw into DUT and can boot successfully Signed-off-by: Joey Peng <joey.peng@lcfc.corp-partner.google.com> Change-Id: I580a12ca511d8cde6fee1079e39e6976202da4d6 Reviewed-on: https://review.coreboot.org/c/coreboot/+/57549 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
2021-09-24mb/google/brya/var/kano: Set vGPIO configurationDavid Wu
Due to the vGPIO is not set correctly, without setting those pins for PEG60, CPU cannot communicate with PCH about the clkreq state. BUG=b:200886824 TEST=FW_NAME=kano emerge-brya coreboot chromeos-bootimage Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com> Change-Id: I6adf73103ecb02c67d9a199e13d2ead9b8b2276f Reviewed-on: https://review.coreboot.org/c/coreboot/+/57875 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
2021-09-24mb/google/brya/var/kano: Enable EC keyboard backlightDavid Wu
Enable EC keyboard backlight for kano. BUG=b:192370253 TEST=FW_NAME=kano emerge-brya coreboot chromeos-bootimage Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com> Change-Id: I7f56b92b60cadf72eb02fd8bcb87baf36acc16e5 Reviewed-on: https://review.coreboot.org/c/coreboot/+/57877 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
2021-09-24mb/google/brya/var/kano: Enable SaGv supportDavid Wu
Enable SaGv support for kano BUG=None TEST=FW_NAME=kano emerge-brya coreboot Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com> Change-Id: Ifc537a5137f5e6eb10cd4c160923ea4da1f6b0d0 Reviewed-on: https://review.coreboot.org/c/coreboot/+/57876 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
2021-09-24elogtool: Fix off-by-one error in month in timestampRicardo Quesada
elogtool was setting the timestamp with the wrong value in the month. This CL fixes that by incrementing the month by one. This is needed since gmtime() returns the month value starting at 0. TEST=pytest elogtool_test.py (see next CL in relation chain) Change-Id: I00f89ed99b049caafba2e47feae3c068245f9021 Signed-off-by: Ricardo Quesada <ricardoq@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/57868 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Jack Rosenthal <jrosenth@chromium.org> Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
2021-09-24drivers/genesyslogic/gl9755: Disable ASPM L0s supportBen Chuang
When the entry delay of L0s is less than the entry delay of L1, GL9755 will enter L0s state first. When it exits from L0s state, the time of L1 entry will be reset. Therefore, the conditions for entering L1 state cannot be met. In order to enter L1 state, L0s needs to be disabled. BUG=b:195611000 TEST=Verify GL9755 enters L1 by observing CLKREQ# de-asserts. Signed-off-by: Ben Chuang <benchuanggli@gmail.com> Change-Id: If121b5cb534eb32bac8992683c3f0eee8946acec Reviewed-on: https://review.coreboot.org/c/coreboot/+/57632 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Paul Menzel <paulepanter@mailbox.org> Reviewed-by: Angel Pons <th3fanbus@gmail.com> Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
2021-09-24cpu/x86/mp_init: Add comment to smm_do_relocationRaul E Rangel
It took me a while to understand the SMM set up flow. This adds a clarifying comment. BUG=b:194391185, b:179699789 TEST=None Signed-off-by: Raul E Rangel <rrangel@chromium.org> Change-Id: I9c73e416b8c583cf870e7a29b0bd7dcc99c2f5f4 Reviewed-on: https://review.coreboot.org/c/coreboot/+/57858 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Arthur Heymans <arthur@aheymans.xyz> Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
2021-09-24soc/amd/common: factor out FSP-related parts of common KconfigFelix Held
TEST=Timeless build for Mandolin results in identical image. Signed-off-by: Felix Held <felix-coreboot@felixheld.de> Change-Id: Ib2fb6c29b9f42c00f252994ae2a40b7ff668105a Reviewed-on: https://review.coreboot.org/c/coreboot/+/57885 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Raul Rangel <rrangel@chromium.org>
2021-09-24soc/amd/common: move block/pi out of the block folderFelix Held
Since the binaryPI glue code is specific to a binary interface, but not for a hardware block, move it out of the common blocks directory. This also brings the binaryPI support in line with the FSP support which is used on the newer generations. This also drops the SOC_AMD_COMMON_BLOCK_PI Kconfig option and makes use of the already existing SOC_AMD_PI Kconfig option instead. Signed-off-by: Felix Held <felix-coreboot@felixheld.de> Change-Id: I014e538f2772938031950475e456cc40dd05d74c Reviewed-on: https://review.coreboot.org/c/coreboot/+/57884 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Raul Rangel <rrangel@chromium.org>
2021-09-24soc/amd/common/block: move binaryPI S3 block into PI blockFelix Held
The code in soc/amd/common/block/s3 is specific to the AMD binaryPI coreboot integration, so move the code to soc/amd/common/block/pi. This drops the SOC_AMD_COMMON_BLOCK_S3 Kconfig option and integrates the dependencies and selections into the SOC_AMD_COMMON_BLOCK_PI Kconfig option. Since only selecting SOC_AMD_COMMON_BLOCK_PI but not SOC_AMD_COMMON_BLOCK_S3 resulted in missing functions in the linking process, we don't lose support for any working configuration by only having one Kconfig option for both parts. Signed-off-by: Felix Held <felix-coreboot@felixheld.de> Change-Id: Ib2bd99a88d8b05216688bc45d9c4f23a007ce870 Reviewed-on: https://review.coreboot.org/c/coreboot/+/57883 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Raul Rangel <rrangel@chromium.org>
2021-09-24soc/intel/alderlake: add MaxDramSpeed configCasper Chang
This change add MaxDramSpeed for variants usage to config dram speed. Signed-off-by: Casper Chang <casper_chang@wistron.corp-partner.google.com> Change-Id: Iba0fae0ab4ff0121dc63af792458492eeb21ec2b Reviewed-on: https://review.coreboot.org/c/coreboot/+/57866 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
2021-09-24mb/google/dedede/var/magolor: Add ssfc codec DA7219 supportTyler Wang
Add DA7219 codec support in maglet. BUG=b:198239769, b:196193562 TEST:emerge coreboot Signed-off-by: Tyler Wang <tyler.wang@quanta.corp-partner.google.com> Change-Id: I52d980ed611b3fbe4892cd3e65e3b35931feaba5 Reviewed-on: https://review.coreboot.org/c/coreboot/+/57696 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Ren Kuo <ren.kuo@quanta.corp-partner.google.com> Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
2021-09-24util/abuild: Run `make .xcompile` only onceNico Huber
If abuild called itself recursively, the file already exists and we can spare us one evaluation of all the makefiles per recursive abuild run. Change-Id: Id3e2239354ec251c24c03c971987586deeb026c5 Signed-off-by: Nico Huber <nico.h@gmx.de> Reviewed-on: https://review.coreboot.org/c/coreboot/+/42640 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org> Reviewed-by: Reka Norman <rekanorman@chromium.org> Reviewed-by: Patrick Georgi <pgeorgi@google.com>
2021-09-23kconfig_lint: restrict definition of defaults for choice elementsMichael Niewöhner
Defining defaults for symbols used inside choices is not allowed. Add a check for this, so we can drop the existent, overly restrictive checks in the follow-up change. Change-Id: I45bce2633dbd168fceb81ceae9b68621b28526e8 Signed-off-by: Michael Niewöhner <foss@mniewoehner.de> Reviewed-on: https://review.coreboot.org/c/coreboot/+/57715 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Felix Singer <felixsinger@posteo.net> Reviewed-by: Martin Roth <martinroth@google.com>
2021-09-23soc/amd/common/blocks/include: rename gpio_banks.h to gpio.hFelix Held
This brings the AMD SoC GPIO code in line with the Intel SoC code and removes the not really needed suffix. Signed-off-by: Felix Held <felix-coreboot@felixheld.de> Change-Id: Ie2dbec81dfe503869beb2872b01a7475e2b88b33 Reviewed-on: https://review.coreboot.org/c/coreboot/+/57842 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Raul Rangel <rrangel@chromium.org>
2021-09-23soc/amd/common/blocks: rename gpio_banks folder to gpioFelix Held
This brings the AMD SoC GPIO code in line with the Intel SoC code and removes the not really needed suffix. Signed-off-by: Felix Held <felix-coreboot@felixheld.de> Change-Id: I3dfcca2f126eb49c962b5cc32cbcf72e04f3f170 Reviewed-on: https://review.coreboot.org/c/coreboot/+/57841 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Raul Rangel <rrangel@chromium.org>
2021-09-23mb/intel/adlrvp_m: Enable HECI1 communicationzhixingma
The patch enables HECI1 interface to allow OS applications to communicate with CSE. TEST=Verify PCI device 0:16.0 exposed in the lspci output Signed-off-by: zhixingma <zhixing.ma@intel.com> Change-Id: Ifd338345caa183f03097f1003080992da70296ff Reviewed-on: https://review.coreboot.org/c/coreboot/+/57813 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Sridhar Siricilla <sridhar.siricilla@intel.com> Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
2021-09-23soc/amd: rename program_gpios to gpio_configure_padsFelix Held
Use the same function name as in soc/intel for this functionality. This also brings the function name more in line with the extended version of this function gpio_configure_pads_with_override which additionally supports passing a GPIO override configuration. This might cause some pain for out-of-tree boards, but at some point this should be made more consistent, so I don't see a too strong reason not to do this. Signed-off-by: Felix Held <felix-coreboot@felixheld.de> Change-Id: I88852e040f79861ce7d190bf2203f9e0ce156690 Reviewed-on: https://review.coreboot.org/c/coreboot/+/57837 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Raul Rangel <rrangel@chromium.org>
2021-09-23soc/amd,intel/common/include/gpio: improve documentation of overridesFelix Held
Explicitly point out that gpio_configure_pads_with_override will ignore GPIOs that are only in the override configuration, but not in the base configuration. Signed-off-by: Felix Held <felix-coreboot@felixheld.de> Change-Id: I1bdfcac89b81fef773938133a2699897c6ee9415 Reviewed-on: https://review.coreboot.org/c/coreboot/+/57836 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Raul Rangel <rrangel@chromium.org> Reviewed-by: Furquan Shaikh <furquan@google.com>
2021-09-23mb/google/brya/variants/gimble: Update DPTF sensorsMark Hsieh
Add two thermal sensors for fan and charger for DPTF based thermal control. BUG=b:199180746 TEST=USE="project_gimble emerge-brya coreboot" and verify it builds without error. Signed-off-by: Mark Hsieh <mark_hsieh@wistron.corp-partner.google.com> Change-Id: I1529dd5dff3445dd499ed665386a9b06d67c7028 Reviewed-on: https://review.coreboot.org/c/coreboot/+/57833 Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2021-09-23mb/google/brya/variants/gimble: Update audio settingMark Hsieh
Add vmon-slot-no,imon-slot-no and dsm_param_file_name in overridetree.cb BUG=b:197701952 TEST=build and check SSDT Signed-off-by: Mark Hsieh <mark_hsieh@wistron.corp-partner.google.com> Change-Id: Ie646360c4ebbf25762b374c5bc3ef2017989fb2f Reviewed-on: https://review.coreboot.org/c/coreboot/+/57832 Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org> Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
2021-09-23util/crossgcc: Update gcc to 11.2Patrick Georgi
Various fixes to gnat and the improved nds32 backend have been merged into gcc by now, so we don't need to carry those patches anymore. Change-Id: Icdee2a8beedd109ee1f0eef6f32f7accbf66674b Signed-off-by: Patrick Georgi <pgeorgi@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/54050 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Nico Huber <nico.h@gmx.de>
2021-09-23util/spd_tools: Remove old lp4x and ddr4 versions of spd_toolsReka Norman
The migration to the new unified version of spd_tools is complete, so the old lp4x and ddr4 versions can be removed. BUG=b:191776301 TEST=None Signed-off-by: Reka Norman <rekanorman@google.com> Change-Id: I6b1fc297739efc8dc7d7eec64956bf3343984604 Reviewed-on: https://review.coreboot.org/c/coreboot/+/57822 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
2021-09-23util/spd_tools: Sort platforms_manifest entries by set numberReka Norman
Ensure that the order of entries in each platform manifest is consistent every time spd_gen is run. BUG=b:191776301 TEST=Run spd_gen for lp4x and ddr4, check that the manifests are unchanged. Change-Id: I7bfea65c8fc781df80a8725c0cf20c7547c857e8 Signed-off-by: Reka Norman <rekanorman@google.com> Reviewed-on: https://review.coreboot.org/c/coreboot/+/57773 Tested-by: build bot (Jenkins) <no-reply@coreboot.org> Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-11 08:58:07 +0000