| Age | Commit message (Collapse) | Author |
|---|
|
Test: Generated GPIO for ASRock Rack SPC741D8-2L2T/BCM.
Change-Id: Ib7ded47fb1c0b87ebb3cecaf3e41319ac552b797
Signed-off-by: Fabian Meyer <fabian.meyer@student.kit.edu>
Co-authored-by: Yussuf Khalil <yussuf.khalil@kit.edu>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82204
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Maxim <max.senia.poliak@gmail.com>
|
|
Disable devices in variant.c instead of adding probe statements to
devicetree because storage devices need to be enabled when fw_config is
unprovisioned, and devicetree does not currently support this (it
disables all probed devices when fw_config is unprovisioned).
BUG=b:337169542
TEST=Local build successfully.
Change-Id: I3d71a35e9c0a33b72720b093b5a05eb69d5bb9f8
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83060
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Add initial override devicetree for riven based on
the latest schematic (Riven(ZDK)_MB_Proto_0601.pdf).
1. Add eMMC DLL tuning value (copy from craask)
2. Configure I2C frequency (copy from craask)
3. Add audio codec and speaker amp settings
4. Add Elan touchscreen settings (copy from craask)
5. Add WFC and usb settings (copy from craask)
6 Add Elan and Synaptics touchpad settings (copy from craask)
7. Add WIFI6(CNVI) and WIFI7(PCIE) configuration
8. Add LTE settings (copy from craask)
BUG=b:337169542
TEST=Local build successfully.
Change-Id: I1dda3557edb44dda9c3a1efaf98437352978561c
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83059
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
In preparation for introducing other yes/no prompts, factor out the
logic into a common function.
Change-Id: Iff1f0c6c665a5352013122fb791121a116c434f3
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82402
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
device/device.h provides the definition of struct device.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Id1c3c09665e3eedec6055f4a0586016c5a5537bc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83083
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Elan touchpad driver in newer linux kernels (>= 5.15) no longer
explicitly configures the touchpad as a wakeup source for devices
not using device tree. It is now assumed this information should be
extracted from ACPI, therefore we need to update drallion's devicetree
so that the device regains its lost capability.
TEST=update drallion FW and verify touchpad can cause wake up from
suspend
Change-Id: Iff21afda144cc11a013cb72816064df1c9eb21ae
Signed-off-by: Angela Czubak <aczubak@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83070
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Under Windows ACPI, GpioInt and _PRW must be mututally exclusive within
the scope of a device, otherwise a BSOD occurs with an ACPI_BIOS_ERROR.
To enforce this, only use _PRW when EC_ENABLE_SYNC_IRQ_GPIO is not set.
If both EC_ENABLE_WAKE_PIN and EC_ENABLE_SYNC_IRQ_GPIO are set, then
ensure that the GpioInt is flagged as ExclusiveAndWake (vs just
Exclusive) so that the CREC device is still able to wake the device
as needed.
TEST=Build/boot google/{nocturne,frostflow} to Win11 w/ sync_irq_gpio
and wake_pin both enabled.
Change-Id: Ia59cce2ee12bfc8d3ac0173a7a4ec88d7079a958
Signed-off-by: CoolStar <coolstarorganization@gmail.com>
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82233
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enables ACPI brightness controls to be generated, and display
brightness controls to be functional under Windows.
TEST=build/boot Win11 on google/brya (craaskin), verify display
brightness controls present and functional.
Change-Id: I821b912cf52b5b89c5c9d831a5a15566b1b31639
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83071
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
Boards using the brya baseboard already generate ACPI brightness
controls via their use of the gfx/generic driver, but need the
default brightness steps in order for display brightness control
to be functional under Windows.
TEST= build/boot Windows 11 on banshee, verify brightness controls
functional.
Change-Id: I03bb7a7309476839c49d2e862a036d9e89800605
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/70372
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Lotso's WIFI_BT is same design as brox, copy from brox.
BUG=b:339612353
TEST=emerge-brox coreboot chromeos-bootimage and boot on
Change-Id: I3946297db7f10a31570f773bdc5665f9f472c9fe
Signed-off-by: Jian Tong <tongjian@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83053
Reviewed-by: Wentao Qin <qinwentao@huaqin.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Configure GPIOs according to schematic_20240607.
BUG=b:333486830
BRANCH=firmware-nissa-15217.B
TEST=emerge-nissa coreboot
Change-Id: I760a7a234df43db3a557b3be9e20ff7aa5f80b72
Signed-off-by: Amanda Huang <amanda_hwang@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82661
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
This patch selects USE_UNIFIED_AP_FIRMWARE_FOR_UFS_AND_NON_UFS which intends to achieve a unified AP firmware image across UFS and non-UFS skus.
BUG=b:328580882
TEST=Local build successfully.
Change-Id: Ifcee68a3492ab4606819de0be41701f803151f66
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83061
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
Change-Id: I3cb0a39c83d6c92d604f1190538db88d97a81693
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83091
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nicholas Chin <nic.c3.14@gmail.com>
|
|
Also, remove superfluous comments from devices which repeat their name.
Change-Id: I26f7d5155f73bcf3cb3872f206c946da5029bda8
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83090
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nicholas Chin <nic.c3.14@gmail.com>
|
|
If both CONFIG_SEPARATE_ROMSTAGE and CONFIG_BOOTBLOCK_CONSOLE are not
set, compilation will fail with errors indicating redefinitions of
various console methods.
When BOOTBLOCK_CONSOLE is not set, the __CONSOLE_ENABLE__ macro in
include/console/console.h evaluates to zero when compiling the
bootblock, resulting in various console methods being defined as stubs
in the header. In a typical build with a separate bootblock and
romstage, this will not cause a conflict as the non-stub definitions
found in the console/*.c files are added conditionally to the bootblock
depending on CONFIG_BOOTBLOCK_CONSOLE.
When SEPARATE_ROMSTAGE is not set, the list of romstage objects gets
added to the bootblock. Since the console sources were unconditionally
added to romstage, the non-stub definitions were able to slip into the
bootblock, causing a redefinition of the stubs.
Avoid this by conditionally adding these sources to romstage depending
on CONFIG_SEPARATE_ROMSTAGE. If SEPARATE_ROMSTAGE is set, the non-stub
definitions are handled in the same way as they were before. If it is
not set, the union of bootblock and romstage objects will only include
the non-stub definitions based on CONFIG_BOOTBLOCK_CONSOLE, which uses
existing console/Makefile.mk rules for the bootblock.
TEST=qemu-i440fx builds successfully with all possible settings of
CONFIG_SEPARATE_ROMSTAGE and CONFIG_BOOTBLOCK_CONSOLE.
Change-Id: I59b3f0c52a4338b1573e0a647bc16cec4943fd7f
Signed-off-by: Nicholas Chin <nic.c3.14@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83088
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
This change also drops a duplicated config default line, which might be
why this was omitted.
Change-Id: I2b4c8b316adaadec3e49d5162b37b37629331b06
Signed-off-by: Benjamin Doron <benjamin.doron@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83086
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Also, remove superfluous comments from devices which repeat their name.
Change-Id: Ia4a9a5c5897fe78a1243e4c42a7d8753cfe039c0
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83095
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
|
|
Change-Id: I20aca1a63306b0f39f97fd0b85d61cd957cb2150
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83094
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Also, remove superfluous comments from devices which repeat their name.
Change-Id: I00473e44fce9197f818f5a8d131e9be31e8b0f69
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83093
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I6026498c2853f5951227ace57b7198579f342647
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83092
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
As of commit ee12634872 (nb/sandybridge,sb/bd82x6x: Configure USB from
southbridge devicetree) and earlier commits, the USB port configuration
should be located in the devicetree instead of the mainboard_usb_ports
array, typically located in the boards early_init.c.
TEST=USB ports still function; and the USBIRx, USBPDO, USBOCM1, and
USBOCM2 RCBA registers in the inteltool dump did not change between
an E6430 build before and after the sb/intel/bd82x6x that moved the
usb config to the devicetree.
Change-Id: Ia5aa03a5894a8ef29e863470925a223f52e0ab70
Signed-off-by: Nicholas Chin <nic.c3.14@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83006
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Instead of using a relative path for the submodules, specify the sub-
module URLs as pointing at coreboot.org, using https.
While the relative path works well for coreboot itself, when the repo
is forked and fetched from from anywhere other than review.coreboot.org,
this file either needs to be modified, or all the submodules need to be
checked out as well.
Change-Id: Ie4f95c70a7f194d1073dc561c9f33dcc108060cc
Signed-off-by: Martin Roth <gaumless@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80552
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
|
|
The components listed in the documentation work in this port.
The MXM structure of the vendor firmware is added, which is
used by the VGA option ROM with int15h functions.
Change-Id: I15181792b1efa45a2a94d78e43c6257da1acf950
Signed-off-by: Iru Cai <mytbk920423@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39398
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
The host bridge PCI device ID can be changed by the firmware. There
is no documentation about it, though. There's 'official' IDs, which
appear in spec updates and Windows drivers, and 'mysterious' IDs,
which Intel doesn't want OSes to know about and thus are not listed.
For the sake of completeness, add the PCI device IDs for Clarkdale.
Though coreboot only supports Arrandale, both of them are Ironlake.
It is possible that the Management Engine handles changing the PCI
device ID, which would not happen when using a broken ME firmware.
Change-Id: I85a48fcf0e0e62f42fe147a5d4e2d557b2143e5b
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/60215
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
It's in particular useful for working with variables that contain 64-bit
pointers, like CapsuleUpdateData* global variables defined by UEFI
specification.
Change-Id: I4b46b41cdc5f69d4ca189659bef1e44f64c0d554
Signed-off-by: Sergii Dmytruk <sergii.dmytruk@3mdeb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82611
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Krystian Hebel <krystian.hebel@3mdeb.com>
|
|
These data types were added during review of CB:79080 but they weren't
added to the help message.
Change-Id: I6e79d65c80c292c3f5d2a2611e602db5cc6cf374
Signed-off-by: Sergii Dmytruk <sergii.dmytruk@3mdeb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82610
Reviewed-by: Krystian Hebel <krystian.hebel@3mdeb.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Maciej Pijanowski <maciej.pijanowski@3mdeb.com>
|
|
TEST=Build and boot on intel/archercity CRB
Change-Id: I4f9e606cf9ec01ec157ef4dd7c26f6b5eb88c7b7
Signed-off-by: Jincheng Li <jincheng.li@intel.com>
Signed-off-by: Shuo Liu <shuo.liu@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82941
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Turn off camera power during s0ix to improve power consumption.
BUG=None
BRANCH=brya
TEST=built and verified GPP_A17 went to low during s0ix with a scope.
[Measurement of s0ix power consumption - 1 hour avg]
Before this: 301.4 mW
After this: 299.8 mW
Change-Id: Iae02d06e9f5a5988563b2b7ae36d153aecedb9d7
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83029
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: YH Lin <yueherngl@google.com>
|
|
Trying to probe RAM space to figure out top of memory causes an
exception on RISC-V virtual machines with recent versions of QEMU, but
we temporarily enable exception handlers for that and use it to help
detect if a RAM address is usable or not. However, QEMU docs recommend
reading device information from the device-tree blob it provides us at
the start of RAM.
A previous commit adds a library function to parse device-tree blob that
QEMU provides us. Use it to determine top of memory in RISC-V QEMU
virtual machines, but still fall back to the RAM probing approach as a
last-ditch effort.
Change-Id: I9e4a95f49ad373675939329eef40d7423a4132ab
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80363
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Maximilian Brune <maximilian.brune@9elements.com>
|
|
The OpenTitan HW implements the same firmware interface as the Ti50
H1D3C hardware variant; it just has a different DID_VID. Allow this new
DID_VID to be recognized correctly.
BUG=b:324940153
Change-Id: Iaacf6d88bc6067948756c465aac1cd8b24ecae1f
Signed-off-by: Jett Rink <jettrink@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83033
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Every now and then we have discussions about blobs and how and if they
should be introduced or handled. This patch adds a clear statement on
the project's view on this topic to avoid unclear situations in the
future.
Change-Id: I20bc0b345c129ecd59aa1190647d89f6d4e07d46
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82086
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
This patch eliminates coreboot from loading microcode from RW CBFS
(when the RO descriptor is locked, which indicates a fixed RO image)
because the kernel can already patch the microcode on BSPs and APs
while booting to OS.
This may be a chance to lower the burden on the AP FW side because
patching microcode on in-field devices is subject to firmware updates,
which are rarely published and, if required, must go through the
firmware qualification testing procedure (which is costly, unlike
kernel updates for ucode updates).
1. The FIT loads the necessary microcode from the RO during reset.
2. Reloading microcode from RW CBFS impacts boot time
(~60ms, core-dependent).
3. The kernel can still load microcode updates.
ChromeOS devices leverage RO+RW-A/RW-B booting. The RO's microcode is
sufficient for initial boot, and the kernel can apply updates later.
BUG=none
TEST=Verified boot optimization; in-field devices skip RW-CBFS microcode
loading when RO is locked.
Change-Id: I68953d45d3624aba0a3be28bc7b266b7621ddcc4
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82999
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
While both APL and GLK load the CPU microcode from FIT, only GLK
supports the PRMRR/SGX feature. When this feature is supported, the
FIT microcode load will set the msr (0x08b) with the patch id/revision
one less than the revision in the microcode binary. This results in
coreboot attempting (and failing) to reload the microcode again in
ramstage. Avoid the microcode reload attempt for GLK by using a SoC-
specific microcode update check which accounts for the off-by-1 when
comparing versions.
Implementation is based on the one used for SKL and CNL, but modified
based on feedback in comments on Gerrit.
TEST=build/boot google/reef (electro) and google/octopus (ampton),
verify in cbmem console log that CPU microcode update in ramstage is
skipped due to already being up to date, and that GLK uses the
SoC-specific check and APL uses the non-specific/general one.
Change-Id: Iab97f23d4388d5057797bb13f585db821c735bd0
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83037
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Sean Rhodes <sean@starlabs.systems>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
- Physical DP ports are DP2/DP3 (HDMI2/HDMI3 for DP++)
- VGA port is Analog
- DP1 is not connected
Signed-off-by: Mate Kukri <kukri.mate@gmail.com>
Change-Id: I8ed79167d5445d607acbee491c3382ff2585583f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83049
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
When dynamically generating the DOD (Display Output Device) device
address (_ADR), don't set the DOD constraint flags; only set them when
using the address value to generate the DOD package.
This fixes ACPI brightness control functionality under Windows 11.
Before: Name (_ADR, 0x80010400)
After: Name (_ADR, 0x00000400)
TEST=build/boot Win11 on google brya (banshee), ensure display
brightness controls present and functional.
Ref: ACPI Spec 6.5 Appendix B.6.1 - _ADR
Change-Id: I1d710c6e55e6cb1d20d580bd784221ee1482b871
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83025
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Removed an extra space character from the `printf` format string in
`dump_exception_state` to ensure proper alignment of register values
when printed during exception handling.
BUG=b:336265399
TEST=Built and booted google/rex64 successfully.
Verified correct alignment in exception state dumps.
Change-Id: I8ff92775e32ee754967b1b0a43cd68971b4aadfc
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83047
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add RAM region so that the payload can be placed in there without
coreboot complaining that the payload doesn't target a RAM region.
Signed-off-by: Maximilian Brune <maximilian.brune@9elements.com>
Change-Id: Id07eae3560ce69cd8a6a695702fa0b4463c50855
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81909
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
OpenSBI often breaks if you update it. This should ensure that jenkins
keeps an eye on it.
Signed-off-by: Maximilian Brune <maximilian.brune@9elements.com>
Change-Id: I2101b194bf0d74f4f444fba507e0294bddc746d3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81859
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
OpenSBI got bigger and doesn't fit anymore in 128K which causes coreboot
to not compiler anymore because the region overlaps with ramstage
This patch simply increases the size and uses the OpenSBI linker macro
instead.
Signed-off-by: Maximilian Brune <maximilian.brune@9elements.com>
Change-Id: If1ccaafbf91dae986c470020faf9c0b4fba448e5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83046
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Enable the fixed boot mode option in the VBT and set it to 1920x1080,
so that drobit boards equipped with 4K screens are legible at boot.
TEST=build/boot drobit w/4K screen using edk2 payload, verify boot
resolution set to 1080p and UEFI menus readable without a magnifying
glass.
Change-Id: If1f9e36d9bbdc2955ba890e2832aa64af9ba8f73
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83024
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Generate RAM IDs for
K3KL6L60GM-MGCT
H9JCNNNBK3MLYR-N6E
K3KL8L80DM-MGCU
MT62F1G32D2DS-023 WT:C
H58G56BK8BX068
BUG=b:333494257
BRANCH=None
TEST=Run part_id_gen tool without any errors
Change-Id: I7a240a263816193b9f3d418385c1673e9d3f89db
Signed-off-by: Kun Liu <liukun11@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83040
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Jian Tong <tongjian@huaqin.corp-partner.google.com>
|
|
Based on lotso EVT schematics update gpio settings.
GSPI0_CS0_L -> NF7
GSPI0_MISO -> NF7
GSPI0_MISO -> NF7
GPP_F18 -> EDGE_SINGLE
BUG=b:333494257
TEST=emerge-brox coreboot chromeos-bootimage and boot on
Change-Id: I12d84538566c4d51fe346eb5609e55d91ddafbea
Signed-off-by: Jian Tong <tongjian@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83039
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Kun Liu <liukun11@huaqin.corp-partner.google.com>
|
|
Update autoport for:
1. Commit ee126348726b ("nb/sandybridge,sb/bd82x6x: Configure USB from
southbridge devicetree")
2. Commit 94625d2aae76 ("sb/intel/bd82x6x: Allow actual USBIRx values
for native USB config")
As a side effect of #2 above, no more (broken anyway) FIXME comment
will be written for usb_port_config.
Change-Id: I3b8f44d9de19a7446e2fbcbce1aab6ec6583ebe3
Signed-off-by: Keith Hui <buurin@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82656
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Pujjoga support EM060 WWAN, use wwan_power.asl to handle the
power off sequence.
BUG=b:346479638
TEST=Build and boot on pujjoga
Change-Id: I1273d09385c661835d741691b3c4af26e72a9f86
Signed-off-by: Leo Chou <leo.chou@lcfc.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83042
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Currently, the P sensor does not work.
So add SX9324 registers settings based on tuning value from SEMTECH.
BUG=b:340749850
TEST=Check i2c register settings on Pujjoga and
confirm P sensor function can work by kernel 6.6 driver.
Change-Id: I205c1f5228d792afc763a06f74a8744918e2da75
Signed-off-by: Leo Chou <leo.chou@lcfc.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82689
Reviewed-by: Derek Huang <derekhuang@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Add AX211 wifi sar table for sundance wifi sar config.
Use fw_config to separate different wifi card settings.
WIFI_SAR_TABLE_AX211: 0
BUG=b:332978681
Test=emerge-nissa coreboot
Change-Id: Ide84996da567e4f866a2a1309a6976ed8df635a6
Signed-off-by: Leo Chou <leo.chou@lcfc.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83044
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
Add FW_CONFIG probe based on sundance boxster of below devices:
WWAN
Schematic version: NEC_SHIKIBU_ADL_N_MB_EVT_20240330
BUG=b:332978681
TEST=Boot to OS and verify the WWAN devices is set based on
fw_config.
Change-Id: I14339201d8ee21c85fefa96a49323e0c25cb8eca
Signed-off-by: Leo Chou <leo.chou@lcfc.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83041
Reviewed-by: Eric Lai <ericllai@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Disable devices in variant.c instead of adding probe statements to
devicetree because storage devices need to be enabled when fw_config is
unprovisioned.
BUG=b:345112878
BRANCH=firmware-nissa-15217.B
TEST=emerge-nissa coreboot chromeos-bootimage
Change-Id: I1e5e49c1baa8d2b00134c26cc3b69aa15712b512
Signed-off-by: Amanda Huang <amanda_hwang@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82907
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
We use ALC256 as HDA codec on orisa. Add verb table and the
related device tree changes for HDA related registers.
BUG=b:338523452
BRANCH=firmware-nissa-15217.B
TEST=emerge-nissa coreboot
Change-Id: I92051886341bd317cce6061ece83439d156b0f90
Signed-off-by: Amanda Huang <amanda_hwang@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82719
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
Add override devicetree based on schematic_20240607.
BUG=b:333486830
BRANCH=firmware-nissa-15217.B
TEST=emerge-nissa coreboot
Change-Id: Id3ceff41fdb8e4a57bd6dab6247b622a5d13587d
Signed-off-by: Amanda Huang <amanda_hwang@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82714
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
BUG=none
TEST=Build and verify on Screebo
TEST=make unit-tests
```
$ make tests/commonlib/bsd/string-test
[==========] tests_commonlib_bsd_string-test(tests): Running 1 test(s).
[ RUN ] test_skip_atoi
[ OK ] test_skip_atoi
[==========] tests_commonlib_bsd_string-test(tests): 1 test(s) run.
[ PASSED ] 1 test(s).
```
Change-Id: Ifaaa80d0c696a625592ce301f9e3eefb2b4dcd98
Signed-off-by: Maximilian Brune <maximilian.brune@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82910
Reviewed-by: Jakub Czapiga <czapiga@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
This commit adds the VBIOS table, extracted from Linux sysfs running on
the stock firmware version 8.02, to the coreboot tree, required for
some graphics backends.
Change-Id: I0d1c9795741e112154bfe6885eea744538373d5a
Signed-off-by: Reagan Bohan <xbjfk.github@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82460
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
This commit defines the panel_cfg register for the Razer Blade Stealth
(Kaby Lake). This enables libgfxinit support. These values are derived
from the stock firmware. First, VBIOSes were extracted from the stock
firmware. Then, intelvbtool was used to extract the VBT from each of the
VBIOS tables. Finally, intel_vbt_decode from igt-gpu-tools was used to
extract the register values. Although there were multiple VBIOSes
present in the firmware, all VBIOSes across both firmwares (on version
1.50 for the H2U and 8.02 for the H3Q) had the same register values.
Change-Id: I4c8b26ffb7a70d08655986084a714206d9d0c96a
Signed-off-by: Reagan Bohan <xbjfk.github@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82458
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Commit 88decca14f84 ("ACPI: Add helper fill_fadt_extended_pm_io()")
moved the population of the extended FADT to a separate function, but
incorrectly placed that function call before various length fields were
populated, leading to spurious validation errors in the cbmem boot log.
Correct this by moving the call to fill_fadt_extended_pm_io() after
the required fields are populated.
TEST=build/boot google/slippy (wolf), verify no FADT errors in cbmem
console log.
Change-Id: I1f8522e4813e6071692206f2b7ad2a2f5086071e
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83035
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Change-Id: I0e5fba7db7d97835001934cb140f4c76bdc46d3e
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82889
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
Change-Id: Icb9e72edf3a982a095dceee4da19f90c53fcddd0
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83021
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
Fill in memory config based on the the schematic_20240607.
BUG=b:333486830
BRANCH=firmware-nissa-15217.B
TEST=emerge-nissa coreboot
Change-Id: I1456f7385e092b606fc0a35b25f3454600af8b23
Signed-off-by: Amanda Huang <amanda_hwang@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82662
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
All of the Dell Latitudes from GM45 and until at least Haswell use a
derivative of the MEC5035 EC, and I have been actively working on
coreboot support for this EC and boards that use it. Rename the "E6400
MAINBOARD" section to "DELL LATITUDE" and add mb/dell/snb_ivb_latitude
and mb/dell/e7240 as additional paths.
Change-Id: I7ba46980bfc8569a85593e415f01cc83fe7d67d7
Signed-off-by: Nicholas Chin <nic.c3.14@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83008
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Commit 45e4ab4a660c (mb/*: Update SPD mapping for sandybridge boards)
changed the way in which SPD addresses are set up for SNB/IVB boards,
but autoport was not updated to reflect these changes. Result is:
register "spd_addresses" = "{0x50, 0x51, 0x52, 0x53}" # FIXME: Put proper SPD map here"
The stray quote at the end is irritating, but is hard to get rid of
without substantial refactoring of autoport's guts. But, given that
this is a FIXME comment, anyone using autoport should just drop the
comment after verifying the SPD map, so it's not a big deal.
In addition, update the corresponding section of the README, which
was horrendously out-of-date.
Change-Id: I6ad38f53afc4fafb45be7f086723cc0782a965ed
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82405
Reviewed-by: Keith Hui <buurin@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Refer to the reference board of nivviks, and update GPIO settings
based on latest schematic (Riven(ZDK)_MB_Proto_0601.pdf).
BUG=b:337169542
TEST=Local build successfully.
Change-Id: Ic43c743fcc2ec89b5a9e2fbe1a87b833d59f1e74
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82973
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The word "experimental" has been removed from the help text for
HAVE_X86_64_SUPPORT Kconfig. This is because the x86_64 architecture
has now been officially tested and enabled for several x86 SoC
platforms.
This work will provide us with the foundation we need to begin working
with Intel's next-generation SoC platform (which requires to support
64-bit mode of booting by default).
Therefore, we can now remove the word "experimental" from the
"HAVE_X86_64_SUPPORT" Kconfig help text.
TEST=Able to build and boot google/rex64 in 64-bit mode to ChromeOS.
Change-Id: Ibd629f4e2722f3cbabbe297d4481790c9fa9226a
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83009
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Looks like PCIe root port device IDs for 9-series PCH-H are missing from
commit 434d7d45829e (sb/intel/lynxpoint: Add PCI DIDs for 9 series PCHs)
for some reason. Add them, so that coreboot performs PCIe initialisation
for 9-series PCH-H.
Change-Id: I1589418e5e25daabbf09c66c637e9c4f86aa02a6
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82947
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The H110M does not use memory down, and the spd directory doesn't exist
in the board's directory in the first place. This was probably just copy
and paste leftover from some existing Skylake board in the initial port.
TEST=Timeless build does not change.
Change-Id: I35744310b2bf8a14165dae9808c982e6dc274a74
Signed-off-by: Nicholas Chin <nic.c3.14@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/83010
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Signed-off-by: Maximilian Brune <maximilian.brune@9elements.com>
Change-Id: Ia0a5c48c6314f53c4ed72958f5d6f839f0a5c2ca
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77973
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Based on the non-public "ITE IT8659E-I Preliminary Specification V0.7.2
(For H Version)".
TEST=Initialize IT8659E on the new Protectli platform
Change-Id: I11657ec6e1c880f0cee247071486a904a92bb7a1
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80497
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Based on the non-public "ITE IT8659E-I Preliminary Specification V0.7.2
(For H Version)".
TEST=Dump IT8659E configuration on the new Protectli platform
Change-Id: Ic036f8b99d5bd0107be7850fc4509da1bf020fe5
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80495
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
Add coreboot support for qemu's sbsa-ref (Server Base System
Architecture) machine (-m sbsa-ref).
The qemu-sbsa coreboot port runs on EL2 and is the payload of the
EL3 firmware (Arm Trusted Firmware).
Note that, coreboot expects a pointer to the FDT in x0. Make sure
to configure TF-A to handoff the FDT pointer.
Example qemu commandline:
qemu-system-aarch64 -nographic -m 2048 -M sbsa-ref \
-pflash <path/to/TFA.fd> \
-pflash <path/to/coreboot.rom>
The Documentation can be found here:
Documentation/mainboard/emulation/qemu-sbsa.md
Change-Id: Iacc9aaf065e0d153336cbef9a9b5b46a9eb24a53
Signed-off-by: David Milosevic <David.Milosevic@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79086
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
|
|
Based on autoport output.
It boots to Arch Linux (Linux 6.6.3) from USB and mSATA with SeaBIOS.
Change-Id: I6933bdbcc8d0bbb85d62657624740266284ac71c
Signed-off-by: Iru Cai <mytbk920423@gmail.com>
Signed-off-by: Nicholas Chin <nic.c3.14@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/79746
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
The UsbTcPortEn UPD for FSP-S is being set in ramstage, however the
equivalent FSP-M UPD, the UsbTcPortEnPreMem, was not being set.
Following the Meteor Lake example, set the UsbTcPortEnPreMem UPD
as well for Alder Lake.
Setting this FSP-M UPD will cause FSP to properly program sideband
use BSSB_LSx pins for the enabled Type-C ports. Required for proper
DCI debug and TCSS initialization flow.
Change-Id: If3b79167ec1769ddfb7d28a6c78a3e80bd10afe7
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/80500
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
|
|
Mainboard is QAL80/LA-7781P (UMA). The version with an Nvidia dGPU was
not tested. This is based on the autoport output with some manual fixes.
The VBT was obtained using `intelvbttool --inlegacy --outvbt data.vbt`
while running version A24 (latest version) of the vendor firmware.
The flash is 8MiB + 4MiB, and can be easily accessed by removing the
keyboard. It can also be internally flashed by sending a command to the
EC, which causes the EC to pull the FDO pin low and the firmware to skip
setting up any chipset based write protections [1]. The EC is the SMSC
MEC5055, which seems to be compatible with the existing MEC5035 code.
Working:
- Libgfxinit
- USB EHCI debug (left side usb port is HCD index 2, middle port on the
right side is HCD index 1) with the CH347
- Keyboard
- Touchpad/trackpoint
- ExpressCard (tested with USB 3.0 card)
- Audio
- Ethernet
- SD card reader
- mPCIe WiFi
- SeaBIOS 1.16.3
- edk2 (MrChromebox's fork, uefipayload_202309)
- Internal flashing using dell-flash-unlock
Not working:
- S3 suspend: Possibly EC related, DRAM power is getting cut when
entering S3
- Physical wireless switch: this triggers an SMI handler in the vendor
firmware which sends commands to the EC to enable/disable wireless
devices, and has not been reimplemented
- Battery reporting: needs ACPI code for the EC
- Brightness hotkeys: probably EC related
- The system reports that the power button was pressed and shuts down
when the CPU hits around 86 degrees Celsius, before the CPU can
thermal throttle. Likely EC and possibly PECI related.
- Integrated keyboard with upstream GRUB 2.12 payload: Upstream GRUB
initializes the 8042 PS/2 controller in a way that is incompatible
with how the EC firmware emulates it. GRUB tries to initialize the
controller with scan code set 2 without translation, but the EC only
ever returns set 1 scan codes to the system and thus is only works as
an untranslated set 1 keyboard or a translated set 2 keyboard,
regardless of commands to set the scan code. A USB keyboard works
fine.
Unknown/untested:
- Dock
- eSATA
- TPM
- dGPU on non-UMA model
- Bluetooth module (not included on my system)
[1] https://gitlab.com/nic3-14159/dell-flash-unlock
Change-Id: I93c6622fc5da1d0d61a5b2c197ac7227d9525908
Signed-off-by: Nicholas Chin <nic.c3.14@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/77444
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: Ia3df14ebd365c00902b5d2ba300d8ade4c2d6c26
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82690
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sean Rhodes <sean@starlabs.systems>
|
|
Introduce HAVE_SHARED_PS2_PORT Kconfig for this Super I/O to have
mainboards indicate if they have one shared PS/2 port on the rear
panel. On these boards (where a Y-cable cannot allow both
keyboard and mouse to work off the same port), if a PS/2 keyboard is
not present, SIO should be configured to swap its role to mouse, to
allow the OS to find and initialize any mouse connected.
Supporting code will come in a separate patch. Idea is to condition
them on this Kconfig.
Change-Id: I156b15c6ba233cbe8b9ba4d2cfbca6836ad7483a
Signed-off-by: Keith Hui <buurin@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82631
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Remove USB configurations and data structures from northbridge
devicetree (SNB+MRC boards) and bootblock/romstage C code
(native-only SNB boards). All USB configurations are drawn from
southbridge devicetree going forward.
Change-Id: Ie1cd21077136998a6e90050c95263f2efed68a67
Signed-off-by: Keith Hui <buurin@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81882
Reviewed-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Transfer all USB responsibilities to southbridge/intel/bd82x6x,
using one set of USB port configuration supplied by mainboards
in the southbridge section of their devicetree.
For MRC raminit, export southbridge_fill_pei_data() as a hook for
southbridge code to implement. With new code via this hook, bd82x6x
fills pei_data based on this one set of USB port config.
For native raminit, early_usb_init() now goes directly to the devicetree
and no longer get passed an address to it.
TEST=abuild passes for all affected boards. All USB ports still work
on asus/p8x7x-series/v/p8z77-m.
Change-Id: I38378c7ee0701abc434b030dd97873f2af63e6b0
Signed-off-by: Keith Hui <buurin@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81881
Reviewed-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This board has used the USB current map from asus/p8z77-m_pro since it
first landed in coreboot, which actually doesn't match vendor firmware.
Apply values obtained from hardware while running vendor firmware
to both native and MRC config.
Change-Id: I7ce13493c3ecac8154460c1fedf05e2d70a8e394
Signed-off-by: Keith Hui <buurin@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82756
Reviewed-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
For each sandybridge boards with option to use MRC or native platform
init code, add a copy of the board's USB port config, consolidated between
both code paths, into the southbridge devicetree, using special values
allocated for this consolidation.
These get hooked up in a separate patch.
Change-Id: I53efca3d29b3c5d4d5b7e3d6dc3e6ce6c34201e6
Signed-off-by: Keith Hui <buurin@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81880
Reviewed-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This map is found stored in plain text in vendor firmware image.
They will take effect when USB config is transitioned to southbridge
devicetree.
Change-Id: Iab0a225560856771407bb815ff4d8bc95d0f884f
Signed-off-by: Keith Hui <buurin@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82755
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <patrick.rudolph@9elements.com>
|
|
For mainboards using southbridge/intel/bd82x6x, copy the contents
of mainboard_usb_ports array into southbridge devicetree. In-line
comments are maintained.
Boards also capable of using MRC raminit are done in a separate
patch.
Change-Id: Ia8a967eb3466106f3a34e024260e13d02f449a25
Signed-off-by: Keith Hui <buurin@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81879
Reviewed-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Replace 3 unused values in the map with those found during a Ghidra
examination of MRC binary, and on hardwares running vendor firmware
(asus/p8z77-m and HP Z210 CMT Workstation).
The outgoing values were introduced in commit 216ad2170ca8
("sb/intel/bd82x6x: Add new USB currents") in anticipation for
Gigabyte GA-Z77-DS3H mainboard, but effort to land it was eventually
abandoned. Since commit xxxxxxxxxxxx, such values can be placed
directly in the port config, so there should be no hurdle should that
effort be resurrected.
Add a few #defines in pch.h to place some inline documentation
on MRC values, but more will be documented in the future when this
mapping is introduced MRC-side.
Finally, update autoport to match.
Change-Id: I195c7f627994e48f7a6e6698589504dc96248cff
Signed-off-by: Keith Hui <buurin@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82754
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <patrick.rudolph@9elements.com>
|
|
This is the first step to:
- Move USB port configs, which are static, from C code to devicetree;
- Unify USB port configs between MRC and native code path.
Change-Id: I59af466d41790e2163342cac8676457ac19371ea
Signed-off-by: Keith Hui <buurin@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81878
Reviewed-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Incorporate fixed constants and simple data members into struct
pei_data as it gets initialized and make more use of existing helpers.
Compiler zeroes structs set up this way so the memset() is no longer
needed.
Drop northbridge_fill_pei_data() as it gets replaced entirely.
Gut southbridge_fill_pei_data() in preparation for having southbridge
code fill in USB-related members.
This is to make the code easier to maintain, and realizes small savings
in compiled code size too.
Change-Id: I3140cb99b0106669aa27788641c2895ced048e95
Signed-off-by: Keith Hui <buurin@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82480
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
For USB to work under native code path, the USB port config needs to
include a current setting for each port, which gets mapped to an
initialization value that gets programmed into the USBIRx register
for the respective port. This map resides in early_usb.c.
The need to update it, whenever we see a previously unaccounted for
initialization value, is getting out of hand.
Instead this patch will allow specifying those values, presumably
taken from an inteltool dump while running vendor firmware,
directly in the USB port map.
Because all USBIRx values are always in the 0x20000yyy form, we only
need the lowest 12 bits. We have more than enough space in the USB
port config structure for this.
As the lowest yyy value we saw so far is 0x53, a note is included to
limit the map to not more than 80 entries. Any value that is too big
to be an index into the map is programmed directly, + 0x20000000, into
the registers.
This opens the future possibility to use the map for a simpler
mapping for boards also using MRC, and remove the need for any
mapping at all for the rest.
Change-Id: I3d79b33bac742faa9bd4fc9852aff73fe326de4e
Signed-off-by: Keith Hui <buurin@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82655
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <patrick.rudolph@9elements.com>
|
|
Skip CSE sync in coreboot when payload is doing it.
BUG=b:305898363
TEST=Verify CSE sync from depthcharge on Screebo
Change-Id: Ifa942576c803b8ec9e1e59c61917a14154fb94b2
Signed-off-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82660
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Dinesh Gehlot <digehlot@google.com>
|
|
We are going to expose ths tool to end users, and want to take
care that the presented information can be consumed by them.
The current code simply prints below warnings if we use release
binary available for end-user to download:
No firmware volume header present
No valid firmware volume was found
It will be concerning and not clear to end users, they might not
understant why it happens, what are the implications, and whether
it is something that they should worry about.
This commit tries to explain what actually happens here.
Change-Id: Iaa2678f5ae7c243811484c0567ced97ae0b3fc0a
Signed-off-by: Maciej Pijanowski <maciej.pijanowski@3mdeb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82692
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sergii Dmytruk <sergii.dmytruk@3mdeb.com>
|
|
Change-Id: I90fbd7ce0e1c6cd15d73cb73dc774df2de56b346
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82932
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
|
|
If the EC doesn't know a value, it will report it as 0xffff. In these
cases, calculate a value to used based on others. For example, if the
EC doesn't know the last full charge capacity, report the design
capacity to the OS.
Change-Id: I310555ff913c2e492bbaec4d77281ac32c0de7a3
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81408
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: I559aca98044b7f0e6b08c475b5383c014bb4cd3f
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81407
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Rename the BRPR (Battery Remaining Percentage) to B1RP to match
the format of the other variables.
Change-Id: I64a744d78180156e16dbd483a35c7f97ac84bcba
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81406
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: Iccb60d3530227fb71a3ce5a3ab1421627cc86611
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81405
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The BT1T (temperature) and BT1C (control) are not used so remove
them.
Change-Id: Ie6e85042ec59851bcfb4c88a2e04181c3c39f89c
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81404
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The battery remaining percentage is a uint16_t, so correct this in
the EC memory. This change is non-function, as the EC is little
endian.
Change-Id: I56a0ae8199a95c9722e9bcb4c0739f4ef1d6ab05
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81403
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add BIX Method to report extended battery information.
Change-Id: Ie5baecb20c7d4600e0cf1d19ff5f67ce2003fa1d
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/81402
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
|
|
Add wifi sar table support for xol. Bit 31 in CBI/FW_CONFIG
is used to select different sar table (index 0 or 1) but only
0 is in used at the moment.
BUG=b:344274789
BRANCH=firmware-brya-14505.B
TEST=emerge-brya coreboot chromeos-bootimage
Change-Id: Id4dc74c4f2a807d2e531b419ecb7b590d4c32ac2
Signed-off-by: YH Lin <yueherngl@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82945
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
Current existing temperature thresholds of TSR1 sensor are set at 60C
to start fan. Due to this CPU gets hot and temperature goes over 80C.
In this situation, fan does not even start to lower down CPU temperature.
With updated new settings based on tuning from thermal team, start fan
early at 40C for TSR0 and TSR1 so the CPU temperature stays below 80C.
BUG=b:339493551
TEST=Built and tested on google/brox board
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Change-Id: I4765c13c10e436733d8c9d017085968daa561ccc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82784
Reviewed-by: Eric Lai <ericllai@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Change-Id: If43089560a391d6a844ef1716b277e3146c66945
Signed-off-by: Elyes Haouas <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82861
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
This change restores the EN_PP3300_SSD GPIO configuration in the
ramstage for the Rex0 variant. This is necessary to enable testing
of RO lockdown scenarios on FSI'ed Screbo devices, where bootblock
changes are not applicable.
Additionally, ensures locking the GPIO PAD from getting misconfigured
after booting to OS.
BUG=b/337971452
BRANCH=firmware-rex-15709.B
TEST=Able to boot google/rex with RO locked to an older version without
SSD GPIO refactored, and RW is with the latest revision.
Change-Id: Ia7564b14a20d00e9bb2c9466b7a737dd97f01351
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82909
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
|
|
Add AX211 and AX203 wifi sar table for pujjoga wifi sar config.
Use fw_config to separate different wifi card settings.
WIFI_SAR_TABLE_AX211: 0
WIFI_SAR_TABLE_AX203: 1
BUG=b:336167281
Test=emerge-nissa coreboot
Change-Id: If0f542cb13e93e99960bf65d616b26cee7617a43
Signed-off-by: Leo Chou <leo.chou@lcfc.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82702
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
|
|
Add FW_CONFIG probe based on pujjoga boxster of below devices:
WWAN
Schematic version: 500E_GEN4S_ADL_N_MB_0418
BUG=b:336167281
TEST=Boot to OS and verify the WWAN devices is set based on
fw_config.
Change-Id: I94cb9ffe47888a8b7b5c6837ddfc390a1d2e77d1
Signed-off-by: Leo Chou <leo.chou@lcfc.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82701
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <ericllai@google.com>
|
|
Add bookem new supported memory parts in mem_parts_used.txt.
Generate SPD id for this part.
Zilia SDVB8D8A34XGCL3N3T
BUG=b:344482259
TEST=Use part_id_gen to generate related settings
Change-Id: I1cbf641e2bbe4fd4eea02a1bfa3d6b3c06e567e4
Signed-off-by: Leo Chou <leo.chou@lcfc.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82783
Reviewed-by: Eric Lai <ericllai@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
|
This adds support for Zilia SDVB8D8A34XGCL3N3T LP4x chips.
Generatd SPD data with:
util/spd_tools/bin/spd_gen spd/lp4x/memory_parts.json lp4x
BRANCH=None
BUG=344482259
Change-Id: I4408e62ab2a15002960c1d9659ab6af45bd7f7bb
Signed-off-by: Leo Chou <leo.chou@lcfc.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/82782
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Eric Lai <ericllai@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
|
