summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2017-02-25mainboard/google/reef: keep LPSS_UART2_TXD high in suspend stateAaron Durbin
The cr50 part on reef is connected to the SoC's UART lines. However, when the tx signal is low it causes an interrupt to fire on cr50. Therefore, keep the tx signal high in suspend state so that it doesn't cause an interrupt storm on cr50 which prevents cr50 from sleeping. BUG=chrome-os-partner:63283 BRANCH=reef TEST=s0ix no longer causes interrupt storm on cr50. Power consumption normal. Change-Id: Idaeb8e4427c1cec651122de76a43daa15dc54d0f Signed-off-by: Aaron Durbin <adurbin@chromium.org> Reviewed-on: https://review.coreboot.org/18491 Tested-by: build bot (Jenkins) Reviewed-by: Furquan Shaikh <furquan@google.com>
2017-02-25google/eve: Add rise/fall times for I2C busesDuncan Laurie
Apply tuning for the PCH I2C buses on Eve based on rise/fall time measurements that were done with a scope. BUG=chrome-os-partner:59686 BRANCH=none TEST=Manual testing on Eve P1 to verify that all devices on I2C buses are still functional. Post-tuning measurement will be done once a new firmware is released. Change-Id: I3d70ff455a20ecda374d7e7fa6cd3ab15e7f2621 Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: https://review.coreboot.org/18487 Tested-by: build bot (Jenkins) Reviewed-by: Furquan Shaikh <furquan@google.com>
2017-02-25mainboard/intel/leafhill: Clean upAndrey Petrov
This patch tries to clean the code by: o removing duplication of LPC GPIO pads o removing incorrect definitions from devicetree o removing irrelevant entries from FMD file Also adds vital defaults in Kconfig so it is possible to build an image. Change-Id: Id9913f3b053189166392271152ce5300d82a7de8 Signed-off-by: Andrey Petrov <andrey.petrov@intel.com> Reviewed-on: https://review.coreboot.org/18479 Tested-by: build bot (Jenkins)
2017-02-25nb/amd/amdmct: Remove another currently unused tableJonathan Neuschäfer
This fixes a warning that the new toolchain generates. Change-Id: Idf46026729a474323e74a5cf7a156bf5bc8cf026 Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net> Reviewed-on: https://review.coreboot.org/18485 Tested-by: build bot (Jenkins) Reviewed-by: Martin Roth <martinroth@google.com> Reviewed-by: Patrick Georgi <pgeorgi@google.com>
2017-02-24mainboard/google/poppy: Change touchscreen IRQ to level-triggeredFurquan Shaikh
BUG=chrome-os-partner:62967 BRANCH=None TEST=Verified that touchscreen works on power-on and after suspend-resume as well. Change-Id: Id674cbcc2d524a6ed2883bf9f0e9e076890f9a85 Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/18466 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-02-24src/arch/x86: Remove non-ascii charactersMartin Roth
Change-Id: Ie0d35c693ed5cc3e890279eda289bd6d4416d9e6 Signed-off-by: Martin Roth <martinroth@google.com> Reviewed-on: https://review.coreboot.org/18376 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Patrick Rudolph <siro@das-labor.org> Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org> Reviewed-by: Patrick Georgi <pgeorgi@google.com>
2017-02-24payloads/external/GRUB2: Add "git revision" to the GRUB2 version menuDenis 'GNUtoo' Carikli
This change is based on the following commit: 3aa91dc payloads/seabios: Add "git revision" to the SeaBIOS version menu Change-Id: I9987e3673e70b5cb20173d1ddff6060f42a5374a Signed-off-by: Denis 'GNUtoo' Carikli <GNUtoo@no-log.org> Reviewed-on: https://review.coreboot.org/18352 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Martin Roth <martinroth@google.com>
2017-02-24ec/lenovo/h8: Guard against EC bugs in the battery status logic.Tobias Diedrich
On my Thinkpad with an H8-compatible ENE KB9012 EC (GDHT92WW 1.52), when the battery is nearly full and we switch from battery to AC by plugging in the cable, the current rate will not drop to 0 immediately, but the discharging state is cleared immediately. This leads to the code trying to process an invalid rate value >0x8000, leading to a displayed rate of >1000W. This patch changes the logic to deal with these corner cases. Change-Id: Ideb588d00757f259792e5ae97729e371b63a096c Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de> Reviewed-on: https://review.coreboot.org/18349 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Martin Roth <martinroth@google.com>
2017-02-24arm-trusted-firmware: Disable a couple of warnings for GCC 6.2Martin Roth
- Remove warnings about code using deprecated declarations such as: plat/mediatek/mt8173/bl31_plat_setup.c: In function 'bl31_platform_setup': plat/mediatek/mt8173/bl31_plat_setup.c:175:2: warning: 'arm_gic_setup' is deprecated [-Wdeprecated-declarations] include/drivers/arm/arm_gic.h:44:6: note: declared here: void arm_gic_setup(void) __deprecated; - Disable pedantic warnings to get rid of these warnings: In file included from plat/mediatek/mt8173/bl31_plat_setup.c:36:0: plat/mediatek/mt8173/include/mcucfg.h:134:21: error: enumerator value for 'MP1_CPUCFG_64BIT' is not an integer constant expression [-Werror=pedantic] MP1_CPUCFG_64BIT = 0xf << MP1_CPUCFG_64BIT_SHIFT Change-Id: Ibf2c4972232b2ad743ba689825cfe8440d63e828 Signed-off-by: Martin Roth <martinroth@google.com> Reviewed-on: https://review.coreboot.org/17995 Tested-by: build bot (Jenkins) Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Nico Huber <nico.h@gmx.de>
2017-02-24nb/amd/amdmct: Remove two currently unused tablesJonathan Neuschäfer
This fixes warnings that the new toolchain generates. Change-Id: I83d2c4c4651a89b443121312a5f36adfc1e4bc48 Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net> Reviewed-on: https://review.coreboot.org/18308 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Martin Roth <martinroth@google.com>
2017-02-23mb/emulation/*-riscv: Don't select ARCH_BOOTBLOCK_RISCVJonathan Neuschäfer
It's already selected by SOC_UCB_RISCV. Change-Id: Ic8a14300cdea2a4ab763b2746434891b72843604 Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net> Reviewed-on: https://review.coreboot.org/18390 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Martin Roth <martinroth@google.com>
2017-02-23google/gru: whitespace fixPatrick Georgi
Follow up to https://review.coreboot.org/#/c/18460/ Change-Id: Ic3aada2acf3051622698e10d2e764050e16480d5 Signed-off-by: Patrick Georgi <pgeorgi@chromium.org> Reviewed-on: https://review.coreboot.org/18475 Tested-by: build bot (Jenkins) Reviewed-by: Martin Roth <martinroth@google.com>
2017-02-23google/gru: Tuning USB 2.0 PHY0 and PHY1 squelch detection thresholdWilliam wu
According to USB 2.0 Spec Table 7-7, the High-speed squelch detection threshold Min 100mV and Max 150mV, and we set USB 2.0 PHY0 and PHY1 squelch detection threshold to 150mV by default, so if the amplitude of differential voltage envelope is < 150 mV, the USB 2.0 PHYs envelope detector will indicate it as squelch. On Kevin board, if we connect usb device with Samsung U2 cable, we can see that the impedance of U2 cable is too big according to the eye-diagram test report, and this cause serious signal attenuation at the end of receiver, the amplitude of differential voltage falls below 150mV. This patch aims to reduce the PHY0 and PHY1 otg-ports squelch detection threshold to 125mV (host-ports still use 150mV by default), this is helpful to increase USB 2.0 PHY compatibility. BRANCH=gru BUG=chrome-os-partner:62320 TEST=Plug Samsung U2 cable + SEC P3 HDD 500GB/Galaxy S3 into Type-C port, check if the USB device can be detected. Change-Id: Ia0a2d354781c2ac757938409490f7c4eecdffe61 Signed-off-by: Patrick Georgi <pgeorgi@chromium.org> Original-Commit-Id: 7d74311c25762668386061234df0562f84b7203e Original-Change-Id: Ib20772f8fc2484d34c69f5938818aaa81ded7ed8 Original-Signed-off-by: William wu <wulf@rock-chips.com> Original-Reviewed-on: https://chromium-review.googlesource.com/431015 Original-Commit-Ready: Caesar Wang <wxt@rock-chips.com> Original-Tested-by: Inno Park <ih.yoo.park@samsung.com> Original-Reviewed-by: Julius Werner <jwerner@chromium.org> Reviewed-on: https://review.coreboot.org/18462 Reviewed-by: Martin Roth <martinroth@google.com> Tested-by: build bot (Jenkins)
2017-02-23google/gru: update the pwm regulatorCaesar Wang
As David commented the "Bob and other follow-ons match Gru, Kevin should be the special case here", and update the calculations value for gru/bob board. From the actual tests, some regulator voltage than the actual set of less than 20mv on bob board. (e.g: little-cpus and Center-logic) Update the {min, max} regulator voltage for Bob board. Make sure we get the accurate voltage. BUG=chrome-os-partner:61497 BRANCH=none TEST=boot up Bob, measure the voltage for little cpu and C-logic. Change-Id: Iad881b41d67708776bfb681487cf8cec8518064e Signed-off-by: Patrick Georgi <pgeorgi@chromium.org> Original-Commit-Id: 25e133815f49018e7496c75077b8559c207350a4 Original-Change-Id: I3098c742c7ec355c88f45bd1d93f878a7976a6b4 Original-Signed-off-by: Caesar Wang <wxt@rock-chips.com> Original-Signed-off-by: Shasha Zhao <Sarah_Zhao@asus.com> Original-Reviewed-on: https://chromium-review.googlesource.com/424523 Original-Reviewed-by: David Schneider <dnschneid@chromium.org> Original-Reviewed-by: Brian Norris <briannorris@chromium.org> Original-Signed-off-by: Shasha Zhao <Sarah_Zhao@asus.com> Original-Reviewed-on: https://chromium-review.googlesource.com/430403 Original-Reviewed-by: Julius Werner <jwerner@chromium.org> Reviewed-on: https://review.coreboot.org/18460 Tested-by: build bot (Jenkins) Reviewed-by: Martin Roth <martinroth@google.com>
2017-02-23mb/google/poppy: Enable support for DPTFSumeet Pawnikar
This patch adds the DPTF settings specfic to the mainboard and enables the CPU and other thermal sensors as participant device for poppy. It enables the DPTF flag in the device tree for poppy. It also includes the DPTF specific ASL file in the main DSDT definition. BUG=None BRANCH=None TEST=Built for poppy. Change-Id: If44b01dd3c17fea06681ccf50e8e9f406e642e36 Signed-off-by: Naresh G Solanki <naresh.solanki@intel.com> Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com> Reviewed-on: https://review.coreboot.org/17926 Tested-by: build bot (Jenkins) Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
2017-02-23lynxpoint bd82x6x: Enable PCI-to-PCI bridgeKyösti Mälkki
Once the PCI command register is written the bridge forwards future IO and memory regions, as programmed in the respective base and limit registers, to the secondary PCI bus. It was previously argumented this is copy-paste and never known to be required for these more recent platforms: https://review.coreboot.org/#/c/2706/ Change-Id: Ic8911500a30bc83587af8d4b393b66783fa52e18 Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com> Reviewed-on: https://review.coreboot.org/18330 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-02-23intel/minnow3: follow up with recent changes in masterPatrick Georgi
minnow3 doesn't build right now due to API divergence on master branch. Follow up with recent changes. Change-Id: Iee84750292f22aa040127bcbfe523a0b9eaa8176 Signed-off-by: Patrick Georgi <pgeorgi@chromium.org> Reviewed-on: https://review.coreboot.org/18476 Reviewed-by: Ronald G. Minnich <rminnich@gmail.com> Reviewed-by: Martin Roth <martinroth@google.com> Tested-by: build bot (Jenkins)
2017-02-23google/oak: Add initial support for RowanYidi Lin
Update GPIO controls and mainboard configurations for Rowan. [pg: use the opportunity to clean-up the gerrit-rebase task list with the entirely unrelated Ignore-CL-Reviewed-on lines] BUG=chrome-os-partner:62672 BRANCH=none TEST=emerge-rowan coreboot Change-Id: I110fb368b3d9fa9dfb2bf091342dfb511ff7c09c Signed-off-by: Patrick Georgi <pgeorgi@chromium.org> Original-Commit-Id: f4252cbe94a7456108aaa522e170bca5dcb1fdd1 Original-Change-Id: I18ebc3ccf4c7d051839d7c50e9b0682ef8f09830 Original-Signed-off-by: Yidi Lin <yidi.lin@mediatek.com> Original-Reviewed-on: https://chromium-review.googlesource.com/430557 Original-Reviewed-by: Julius Werner <jwerner@chromium.org> Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/341513 Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/327003 Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/355221 Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/354670 Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/361360 Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/361361 Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/361362 Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/361363 Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/382320 Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/405110 Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/405130 Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/419795 Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/424139 Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/430293 Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/430294 Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/430295 Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/427820 Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/427821 Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/427822 Reviewed-on: https://review.coreboot.org/18463 Tested-by: build bot (Jenkins) Reviewed-by: Martin Roth <martinroth@google.com>
2017-02-23google/gru: improve eye diagram for passing the testCaesar Wang
The children of Gru should share the benefits. In the real world, Bob can't pass the eye diagram tests. BUG=chrome-os-partner:62714 BRANCH=firmware-gru-8785.B TEST=build coreboot Change-Id: I2470bbc81acdaf2458d660dca5dc307cc3038f83 Signed-off-by: Patrick Georgi <pgeorgi@chromium.org> Original-Commit-Id: d0cb3e718a7571f602a00c08a42019851634e7fd Original-Change-Id: I0ccb48bb52eb770ccc9c8c265b07df46b0308dd3 Original-Signed-off-by: Caesar Wang <wxt@rock-chips.com> Original-Reviewed-on: https://chromium-review.googlesource.com/440745 Original-Reviewed-by: Douglas Anderson <dianders@chromium.org> Original-Reviewed-by: Julius Werner <jwerner@chromium.org> Original-Reviewed-on: https://chromium-review.googlesource.com/441468 Reviewed-on: https://review.coreboot.org/18461 Tested-by: build bot (Jenkins) Reviewed-by: Martin Roth <martinroth@google.com>
2017-02-23soc/intel/skylake: Enable Systemagent IMGURizwan Qureshi
Camera and Imaging device should be enabled for camera usecase, FSP provides a UPD to enable/disable the SA IMGU (Imaging Unit) expose the same as a config option in devicetree.cb Also remove a redundant assignment for PchCio2Enable. BUG=None BRANCH=None TEST=lspci should list 00:05:00 Change-Id: I4cf7daf41bfaf4dcba414921cac2e7e12bf89f37 Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com> Reviewed-on: https://review.coreboot.org/18365 Tested-by: build bot (Jenkins) Reviewed-by: Martin Roth <martinroth@google.com>
2017-02-23mt8173: Enable Kconfig options for ChromeOSPaul Kocialkowski
This enables some required Kconfig options when CONFIG_CHROMEOS is set. Change-Id: I290902746c1ea19c8bcb69540e34fde09abb9adf Signed-off-by: Paul Kocialkowski <contact@paulk.fr> Reviewed-on: https://review.coreboot.org/18448 Tested-by: build bot (Jenkins) Reviewed-by: Julius Werner <jwerner@chromium.org>
2017-02-23libpayload: Add oak configPaul Kocialkowski
This adds an oak libpayload config, that should fit all oak-based devices such as elm. Change-Id: Iabb71404ff84029a5976371a353e8c92e781ca1f Signed-off-by: Paul Kocialkowski <contact@paulk.fr> Reviewed-on: https://review.coreboot.org/18447 Tested-by: build bot (Jenkins) Reviewed-by: Julius Werner <jwerner@chromium.org>
2017-02-23mb/apple/macbook21: Remove unused cmos parametersArthur Heymans
These parameters are probably the result of copying from the Thinkpad X60 code. Change-Id: I29763b38618d4b306c37424c5c4b57dfcf69424b Signed-off-by: Arthur Heymans <arthur@aheymans.xyz> Reviewed-on: https://review.coreboot.org/18290 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Nico Huber <nico.h@gmx.de>
2017-02-22intel/minnow3: Implement and configure GPIO tablesBrenton Dong
Copy GPIO table implementation from the google/reef board except with board variant features removed. Also exlcude CrOS GPIO functions. Remove previous romstage GPIO implementation in brd_gpio.h and romstage.c. Configure GPIO settings for MinnowBoard 3. Change-Id: Id2817dcf2f8f196ecd13c810f7f0010a115db566 Signed-off-by: Brenton Dong <brenton.m.dong@intel.com> Reviewed-on: https://review.coreboot.org/18375 Tested-by: build bot (Jenkins) Reviewed-by: Martin Roth <martinroth@google.com>
2017-02-22intel/minnow3: Configure memory properlyBrenton Dong
Set the proper memory configuration for the MinnowBoard 3. The current values are copied from intel/leafhill. Set the proper values for MinnowBoard 3. Change-Id: Ie37842f5ce2cabaa892f42ee945c91fe3ace527a Signed-off-by: Brenton Dong <brenton.m.dong@intel.com> Reviewed-on: https://review.coreboot.org/18374 Tested-by: build bot (Jenkins) Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com> Reviewed-by: Martin Roth <martinroth@google.com> Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
2017-02-22mainboard/intel: Add MinnowBoard 3Brenton Dong
This commit adds the initial scaffolding for the MinnowBoard 3 with Apollo Lake silicon. This mainboard is based on Intel's Leafhill CRB with Apollo Lake silicon. In a first step, it concerns only a copy of intel/leafhill directory with name changes. Special adaptations for MinnowBoard 3 mainboard will follow in separate commits. Change-Id: I7563fe37c89511c7035c5bffc9b034b379cfcaf4 Signed-off-by: Brenton Dong <brenton.m.dong@intel.com> Reviewed-on: https://review.coreboot.org/18298 Tested-by: build bot (Jenkins) Reviewed-by: Martin Roth <martinroth@google.com>
2017-02-22commonlib/fsp.h: include sys/types.h for ssize_tJonathan Neuschäfer
This file reportedly didn't compile on SUSE Linux with gcc 4.3.4: [...] > HOSTCC cbfstool/fsp_relocate.o > In file included from coreboot/src/commonlib/fsp_relocate.c:18: > coreboot/src/commonlib/include/commonlib/fsp.h:26: error: > expected '=', ',', ';', 'asm' or '__attribute__' before > 'fsp_component_relocate' [...] According to POSIX-2008[1], sys/types.h defines ssize_t, so include it. This should not break coreboot code (as opposed to utils code), as we have a sys/types.h in src/include. [1]: http://pubs.opengroup.org/onlinepubs/9699919799/basedefs/sys_types.h.html Change-Id: Id3694dc76c41d800ba09183e4b039b0719ac3d93 Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net> Reviewed-on: https://review.coreboot.org/18417 Tested-by: build bot (Jenkins) Reviewed-by: Nico Huber <nico.h@gmx.de> Reviewed-by: Martin Roth <martinroth@google.com>
2017-02-22intel/i945: Fix up whitespace and indentationPaul Menzel
Fix up the whitespace issues introduced in commit 39bfc6cb (nb/i945/raminit.c: Fix dll timings on 945GC). Change-Id: I3a4152866226401bc51c7fb1752aab541a4c72b0 Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-on: https://review.coreboot.org/18465 Tested-by: build bot (Jenkins) Reviewed-by: Nico Huber <nico.h@gmx.de> Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
2017-02-22nehalem/Kconfig: Rename TRAINING_CACHE_SIZE to MRC_CACHE_SIZEArthur Heymans
This is more consistent with newer Intel targets. Change-Id: I52ee8d3f0c330a03bd6c18eed08e578dd6ae284b Signed-off-by: Arthur Heymans <arthur@aheymans.xyz> Reviewed-on: https://review.coreboot.org/18371 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Patrick Rudolph <siro@das-labor.org>
2017-02-22nb/intel/nehalem: Clean nehalem.hArthur Heymans
Remove unused definitions, prototypes and macros moslty copied from gm45. Change-Id: I076e204885baec3d40f165785cf4ae4adc9154c5 Signed-off-by: Arthur Heymans <arthur@aheymans.xyz> Reviewed-on: https://review.coreboot.org/18370 Tested-by: build bot (Jenkins) Reviewed-by: Patrick Rudolph <siro@das-labor.org> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2017-02-22purism/librem13: Set system type to laptopYouness Alaoui
Change-Id: I3ae80f5727e83a1c9210f0d13fa7fc32c5c79085 Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm> Reviewed-on: https://review.coreboot.org/18412 Reviewed-by: Arthur Heymans <arthur@aheymans.xyz> Tested-by: build bot (Jenkins)
2017-02-22purism/librem13: Fix HDA codec verbs. Use correct codec vendor idYouness Alaoui
There was a 'typo' where the subsystem id was set instead of the codec vendor id. This caused the lynxpoint HDA codecs init to fail to find the proper codecid verbs so codecs were never initialized. That caused the headphones jack to not work. Change-Id: I975031643fc42937ecaea2300639b90632543f67 Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm> Reviewed-on: https://review.coreboot.org/18411 Reviewed-by: Arthur Heymans <arthur@aheymans.xyz> Tested-by: build bot (Jenkins)
2017-02-22purism/librem13: Enable PCIe ports 1 and 2Youness Alaoui
Change-Id: I1fa72e59866ee4aad34d4b60e499f6e37acc367f Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm> Reviewed-on: https://review.coreboot.org/18410 Tested-by: build bot (Jenkins) Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
2017-02-22purism/librem13: Fix M.2 issues.Youness Alaoui
The M.2 SSD is on the SATA port 3, which also required the DTLE setting to be set. This fixes issues with the M.2 SSD not being detected/stable. Change-Id: Id39d9ec395a2d9d32be4c079678d0708f08b3935 Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm> Reviewed-on: https://review.coreboot.org/18409 Tested-by: build bot (Jenkins) Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
2017-02-22Broadwell/Sata: Add support for setting IOBP registers for Ports 2 and 3.Youness Alaoui
The Broadwell SATA controller supports IOBP registers on ports 0 and 1 but Browell supports up to 4 ports, so we need to support setting IOBP for ports 2 and 3 as well. The magic numbers (IOBP SECRT88 and DTLE) for ports 2 and 3 were only guessed by looking at ports 0 and 1 and extrapolating from there. Port 3 has been tested (DTLE setting on Librem 13) and confirmed to work so we can assume that port 2 and 3 magic numbers are valid, but having someone confirm them (through non-public documents?) would be great. Change-Id: I59911cfa677749ceea9a544a99b444722392e72d Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm> Reviewed-on: https://review.coreboot.org/18408 Tested-by: build bot (Jenkins) Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
2017-02-22src/mainboard/digitallogic: Add license headers to all filesMartin Roth
Change-Id: I6a1810360b5c3210038670aea6e80312798a63cd Signed-off-by: Martin Roth <martinroth@google.com> Reviewed-on: https://review.coreboot.org/18406 Tested-by: build bot (Jenkins) Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
2017-02-22src/cpu/x86: Update/Add license headers to all filesMartin Roth
Change-Id: I436bf0e7db008ea78e29eaeef10bea101e6c8922 Signed-off-by: Martin Roth <martinroth@google.com> Reviewed-on: https://review.coreboot.org/18405 Tested-by: build bot (Jenkins) Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
2017-02-22src/cpu/intel: Add license headers to all filesMartin Roth
Change-Id: I5ba8b186972fb59686dcbe11358cd26408cbaf05 Signed-off-by: Martin Roth <martinroth@google.com> Reviewed-on: https://review.coreboot.org/18404 Tested-by: build bot (Jenkins) Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
2017-02-22src/cpu/amd: Update/Add license headers to all filesMartin Roth
Change-Id: I1e0b2b9086db6b3c2f716d9400a83eb60b2ce222 Signed-off-by: Martin Roth <martinroth@google.com> Reviewed-on: https://review.coreboot.org/18403 Tested-by: build bot (Jenkins) Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
2017-02-22arch/x86/acpigen: Provide helper functions for enabling/disabling GPIOFurquan Shaikh
In order to allow GPIOs to be set/clear according to their polarity, provide helper functions that check for polarity and call set/clear SoC functions for generating ACPI code. BUG=None BRANCH=None TEST=Verified that the ACPI code generated remains the same as before for reef. Change-Id: Ie8bdb9dc18e61a4a658f1447d6f1db0b166d9c12 Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/18427 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Tested-by: build bot (Jenkins)
2017-02-22acpi: Add ACPI_ prefix to IRQ enum and struct namesFurquan Shaikh
This is done to avoid any conflicts with same IRQ enums defined by other drivers. BUG=None BRANCH=None TEST=Compiles successfully Change-Id: I539831d853286ca45f6c36c3812a6fa9602df24c Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/18444 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-02-22google/gru: Fix whitespacePatrick Georgi
Change-Id: I538c28fb1bc412947ef9df947fa3f6a3312aeb4b Signed-off-by: Patrick Georgi <pgeorgi@chromium.org> Reviewed-on: https://review.coreboot.org/18322 Tested-by: build bot (Jenkins) Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net> Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Martin Roth <martinroth@google.com>
2017-02-22qualcomm/ipq40xx: add vector operation method to SPIYuji Sasaki
Adding spi_xfer_two_vectors as .xfer_vector for ipq40xx spi_ctrlr. Commit c2973d196d1 ("UPSTREAM: spi: Get rid of SPI_ATOMIC_SEQUENCING") has added a new driver method xfer_vector to support combined write-read operation within a single CS cycle. The method is wrapped in the spi_xfer_vector() API. When spi_ctrlr structure does not have xfer_vector method, API calls write and read operations sequentially. However the QCA40xx SPI driver has "forced" CS activation-inactivation in xfer method, so individual operation will break CS after write operation, making combined write-read cycle broken. Adding xfer_vector method to spi_ctrlr is a simple fix to prevent this. BUG=None BRANCH=none TEST=built and run on Gale Change-Id: I2258e563d0793bcacd626f78b8e96b3649a8e4a4 Signed-off-by: Patrick Georgi <pgeorgi@chromium.org> Original-Commit-Id: 88a8824951cef4fe293dfa6e3a1a837ae07b6156 Original-Change-Id: I031e85ce5b847353cb1084f6f68b2af8c6f702e1 Original-Signed-off-by: Yuji Sasaki <sasakiy@google.com> Original-Reviewed-on: https://chromium-review.googlesource.com/433439 Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org> Original-Reviewed-by: Kan Yan <kyan@google.com> Reviewed-on: https://review.coreboot.org/18297 Tested-by: build bot (Jenkins) Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net> Reviewed-by: Martin Roth <martinroth@google.com>
2017-02-22southbridge/amd: Add LPC bridge acpi path for Family14 and SB800Tobias Diedrich
Adds the necessary plumbing for acpi_device_path() to find the LPC bridge on the AMD Family14 northbridge with an SB800 southbridge. This is necessary for TPM support since the acpi path to the LPC bridge (_SB.PCI0.ISAB) doesn't match the built-in default in tpm.c (_SB.PCI0.LPCB). Change-Id: I1ba5865d3531d8a4f41399802d58aacdf95fc604 Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de> Reviewed-on: https://review.coreboot.org/18402 Reviewed-by: Duncan Laurie <dlaurie@chromium.org> Tested-by: build bot (Jenkins)
2017-02-22soc/intel/skylake: Fix broken suspend-resumeFurquan Shaikh
With recent change (a4b11e5c90: soc/intel/skylake: Perform CPU MP Init before FSP-S Init) to perform CPU MP init before FSP-S init, suspend resume is currently broken for all skylake/kabylake boards. All the skylake/kabylake boards store external stage cache in TSEG, which is relocated post MP-init. Thus, if FSP loading and initialization is done after MP-init, then ramstage is not able to: 1. Save FSP component in external stage cache during normal boot, and 2. Load FSP component from external stage cache during resume In order to fix this, ensure that FSP loading happens separately from FSP initialization. Add fsp_load callback for pre_mp_init which ensures that the required FSP component is loaded/saved from/to external stage cache. BUG=chrome-os-partner:63114 BRANCH=None TEST=Verified that 100 cycles of suspend/resume worked fine on poppy. Change-Id: I5b4deaf936a05b9bccf2f30b949674e2ba993488 Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/18414 Tested-by: build bot (Jenkins) Reviewed-by: Subrata Banik <subrata.banik@intel.com> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-02-22drivers/intel/{fsp1_1,fsp2_0}: Provide separate function for fsp loadFurquan Shaikh
Add a function to allow FSP component loading separately from silicon initialization. This enables SoCs that might not have stage cache available during silicon initialization to load/save components from/to stage cache before it is relocated or destroyed. BUG=chrome-os-partner:63114 BRANCH=None TEST=Compiles successfully. Change-Id: Iae77e20568418c29df9f69bd54aa571e153740c9 Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/18413 Tested-by: build bot (Jenkins) Reviewed-by: Subrata Banik <subrata.banik@intel.com> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-02-22nb/i945/raminit.c: Fix dll timings on 945GCElyes HAOUAS
Values based on vendor bios. TESTED on ga-945gcm-s2l with 667MHz ddr2. Change-Id: I2160f0ac73776b20e2cc1ff5bf77ebe98d2c2672 Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/17197 Reviewed-by: Arthur Heymans <arthur@aheymans.xyz> Tested-by: build bot (Jenkins)
2017-02-21mainboard/google/poppy: Enable Realtek 5663 supportRizwan Qureshi
Enable Realtek RT5663 codec i2c device and add required SSDT parameters. BUG=chrome-os-partner:62051 BRANCH=None TEST=With required driver support in kernel verify audio on headset Change-Id: I9b9eb1e7edca56870f5be0e4fd603c9b0dc7f9de Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com> Reviewed-on: https://review.coreboot.org/18216 Tested-by: build bot (Jenkins) Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Martin Roth <martinroth@google.com>
2017-02-21mainboard/google/poppy: Enable Maxim MAX98927 codecRizwan Qureshi
Enable Maxim 98927 codec i2c device and add required SSDT parameters. BUG=chrome-os-partner:62051 BRANCH=None TEST=with required driver support in kernel verify audio on poppy on-board speakers. Change-Id: Id731de42d77204d59f32ac4c33a245837d6e2107 Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com> Signed-off-by: Dylan Reid <dgreid@chromium.org> Reviewed-on: https://review.coreboot.org/18215 Tested-by: build bot (Jenkins) Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Martin Roth <martinroth@google.com>
2017-02-21mainboard/google/poppy: Generate required nhlt tableRizwan Qureshi
poppy board uses Maxim 98927 speaker codec and Realtek RT5663 for headset. Select the apropriate NHLT blobs to be packaged in CBFS. Also, generate the required ACPI NHLT table for codec and the supported topology in poppy. BUG=chrome-os-partner:62051 BRANCH=None TEST=With the required driver support in kernel verify that the Audio plays on on-board speakers and headset, recording works from on-board mics and headset mics. Change-Id: I98c65038b35fe99a661807de0766e6eac2c80eed Signed-off-by: M Naveen <naveen.m@intel.com> Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com> Signed-off-by: Naresh G Solanki <naresh.solanki@intel.com> Reviewed-on: https://review.coreboot.org/18214 Tested-by: build bot (Jenkins) Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
2017-02-20drivers/i2c: Use I2C HID driver for wacom devicesFurquan Shaikh
Wacom I2C driver does the same thing as I2C HID driver, other than defining macros for Wacom HID. Instead of maintaining two separate drivers providing the same functionality, update all wacom devices to use generic I2C HID driver. BUG=None BRANCH=None TEST=Verified that ACPI nodes for wacom devices are unchanged. Change-Id: Ibb3226d1f3934f5c3c5d98b939756775d11b792c Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/18401 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
2017-02-20google/eve: Set touchscreen I2C bus speed to 1MHzDuncan Laurie
Enable Fast-Plus speed for the touchscreen device so it can be used at 1MHz instead of 400KHz. BUG=chrome-os-partner:61277 TEST=manual testing on Eve P1, needs backported kernel patches to actually make use of any I2C speed other than 400KHz Change-Id: I3f44ff4a02a02a7b05e69ad54d4c6d60e5878393 Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: https://review.coreboot.org/18397 Reviewed-by: Furquan Shaikh <furquan@google.com> Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2017-02-20google/eve: Add audio devicesDuncan Laurie
Add the audio devices to Eve mainboard: - Describe Maxim 98927 speaker amps and RT5663 headphone codec in ACPI so they can be enumerated by the OS. - Supply NHLT binaries for MAX98927, RT5663, and DMIC_4CH. BUG=chrome-os-partner:61009 TEST=manual testing on Eve P1 with updated kernel to ensure that both speakers and headset are functional. DMIC support is is still being worked on and is not yet functional. Change-Id: I5243e35d159a0ed15c6004e94ba5a50b28cff0a9 Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: https://review.coreboot.org/18398 Reviewed-by: Furquan Shaikh <furquan@google.com> Tested-by: build bot (Jenkins)
2017-02-20lenovo/s230u: Add Thinkpad Twist (S230U)Tobias Diedrich
Created using autoport plus some manual work and copying from G505S to account for the non-H8 EC. This model uses the same ENE KB9012 EC as the G505S. Tested: - Mainboard variant with 8GB Elpida DDR3 - SeaBIOS payload - Booting into Linux 4.9.6 with Debian/unstable installed on the internal HDD/SDD slot - Native raminit - Both native VGA init and option rom VGA init - Basic TPM functionality (auto-detection and RNG) - Battery status readout - Basic ACPI functions (power button event; power-off; reboot) - thinkpad-acpi hotkey functions - thinkpad-acpi LED control (red thinkpad LED) - Suspend to RAM and resume works - Mini displayport output works Known issues: - Patches needed for EC battery support https://review.coreboot.org/#/c/18348/ https://review.coreboot.org/#/c/18349/ - No thermal zone since temperature sensing is not H8-compatible and needs to be reverse engineered. Not tested: - msata/wwan (probably works) Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de> Change-Id: I52bc4515277e5c18afbb14a80a9ac788049f485c Reviewed-on: https://review.coreboot.org/18351 Tested-by: build bot (Jenkins) Reviewed-by: Patrick Rudolph <siro@das-labor.org>
2017-02-20mainboard/{google,intel}: Change config option selectionFurquan Shaikh
Change config option selection from "config xyz default y" to "select xyz" if the config option has no dependencies. BUG=None BRANCH=None TEST=Verified that config option selection remains unchanged. Change-Id: I259ae40623b7f4d5589e2caa0988419ba4fefda4 Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/18400 Tested-by: build bot (Jenkins) Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
2017-02-20mainboard/google/reef: Remove config DRIVERS_GENERIC_GPIO_REGULATORFurquan Shaikh
Since we are not using gpio regulators on reef anymore, remove the selection from Kconfig as well. BUG=None BRANCH=None TEST=Compiles successfully. Change-Id: Iae7d88dec3ac476d65b292f97a6ba3add71ce07a Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/18399 Tested-by: build bot (Jenkins) Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
2017-02-20siemens/mc_apl1: Set MAC address for all available i210 MACsMario Scheithauer
This mainboard uses two i210 Ethernet controller. Therfore we enable the usage of the i210 driver and have to provide a function to search for a valid MAC address for all i210 devices by using Siemens hwilib. Change-Id: I36246cdef987fcece15a297ebb2f41561fca1f69 Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com> Reviewed-on: https://review.coreboot.org/18380 Tested-by: build bot (Jenkins) Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
2017-02-20ec/lenovo: Add guards to fix build errors without SMBIOSPaul Menzel
Not selecting the Kconfig option `GENERATE_SMBIOS_TABLES` the build fails with the error below. ``` CC ramstage/ec/lenovo/h8/h8.o src/ec/lenovo/h8/h8.c:201:2: error: unknown field 'get_smbios_strings' specified in initializer .get_smbios_strings = h8_smbios_strings, ^ src/ec/lenovo/h8/h8.c:201:2: error: initialization from incompatible pointer type [-Werror] src/ec/lenovo/h8/h8.c:201:2: error: (near initialization for 'h8_dev_ops.read_resources') [-Werror] cc1: all warnings being treated as errors ``` So add the appropriate preprocessor guards to fix the build error. Change-Id: I3baed452d422539a805c628a8c4a6a8c2a809317 Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-on: https://review.coreboot.org/17770 Tested-by: build bot (Jenkins) Reviewed-by: Patrick Rudolph <siro@das-labor.org>
2017-02-20arch/x86: add functions to generate random numbersRobbie Zhang
Using x86 RDRAND instruction, two functions are supplied to generate a 32bit or 64bit number. One potential usage is the sealing key generation for SGX. BUG=chrome-os-partner:62438 BRANCH=NONE TEST=Tested on Eve to generate a 64bit random number. Change-Id: I50cbeda4de17ccf2fc5efc1fe04f6b1a31ec268c Signed-off-by: Robbie Zhang <robbie.zhang@intel.com> Reviewed-on: https://review.coreboot.org/18362 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-02-20soc/intel/skylake: Expand USB OC pins definition to support PCH-HTeo Boon Tiong
Currently the USB OC pins definition only being defined up to OC3. For PCH-H, OC4 and OC5 are needed, so add both into OC pin enum. Changes is being verified and booted to Yocto with Saddle Brook. Change-Id: Idaed6fa7dcddb9c688966e8bc59f656aec2b26eb Signed-off-by: Teo Boon Tiong <boon.tiong.teo@intel.com> Reviewed-on: https://review.coreboot.org/18364 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-02-20lynxpoint/broadwell: fix PCH power optimizerMatt DeVillier
Setting both bits 27 and 7 of PCH register PMSYNC_CFG (PMSYNC Configuration; offset 0x33c8) causes pre-OS display init to fail on HSW-U/Lynxpoint and BDW-U ChromeOS devices when the VBIOS/GOP driver is run after the register is set. A re-examination of Intel's reference code reveals that bit 7 should be set for the LP PCH, and bit 27 for non-LP, but not both simultaneously. The previous workaround was to disable the entire power optimizer section via a Kconfig option, which isn't ideal. Test: unset bit 27 of PMSYNC_CFG and boot google/lulu, observe functional pre-OS video output Change-Id: I446e169d23dd446710a1648f0a9b9599568b80aa Signed-off-by: Matt DeVillier <matt.devillier@gmail.com> Reviewed-on: https://review.coreboot.org/18385 Tested-by: build bot (Jenkins) Reviewed-by: Martin Roth <martinroth@google.com> Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
2017-02-20Revert "intel/lynxpoint,broadwell: Fix eDP display in Windows, SeaBios & Tiano"Matt DeVillier
We've been able to narrow down the problem to a single register/ single bit, so revert this commit and address the problem in a follow-on commit. This reverts commit 0f2025da0fd4dce6b951b4c4b97c9370ca7d66db. Change-Id: I780f9ea2976dd223aaa3e060aef6e1af8012c346 Signed-off-by: Matt DeVillier <matt.devillier@gmail.com> Reviewed-on: https://review.coreboot.org/18384 Tested-by: build bot (Jenkins) Reviewed-by: Martin Roth <martinroth@google.com>
2017-02-20board-status: Add READMEDenis 'GNUtoo' Carikli
It explains the prerequisites to run the script, some background on how to setup the computer running the script, and the board it gathers the information from. That information is too long to fit inside the script's help. Change-Id: Iecba7310ff1583149c02728e955716775bcbbdc4 Signed-off-by: Denis 'GNUtoo' Carikli <GNUtoo@no-log.org> Reviewed-on: https://review.coreboot.org/6660 Tested-by: build bot (Jenkins) Reviewed-by: Martin Roth <martinroth@google.com>
2017-02-20google/slippy: consolidate variants' common mainboard.asl codeMatt DeVillier
Move code common code from each variant's mainboard.asl into common ACPI code for all variants (like google/auron). This also adds the _PRW method for the LID0 device for falco and peppy, which omitted the function when they were originally upstreamed. See Chromium commit c8b41f7, falco: Add _PRW for LID0 ACPI Device Change-Id: I7f5129340249a986f5996af37c01ccbde8d374e8 Signed-off-by: Matt DeVillier <matt.devillier@gmail.com> Reviewed-on: https://review.coreboot.org/18368 Tested-by: build bot (Jenkins) Reviewed-by: Martin Roth <martinroth@google.com>
2017-02-20nb/i945/raminit: sdram_set_channel_mode Test if DIMM slot 3 is populatedElyes HAOUAS
Add a test in case we have a DIMM2 not populated but DIMM3 is. Change-Id: I14f82afe03884740570838e7b2771233356c518d Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr> Reviewed-on: https://review.coreboot.org/18386 Tested-by: build bot (Jenkins) Reviewed-by: Nico Huber <nico.h@gmx.de>
2017-02-20riscv: Suppress invalid coverity errorsMartin Roth
Coverity is detecting 'sp' as a variable which has not been initialized. This is obviously not correct, so this patch *TRIES* to mark it as false I'm not positive that this will work because the annotation needs to go on the line above the error, but this error is inside of a # define. Does the whole #define count as one line? Can it go on the line above the #define in the .h file? Does it have to precede every line where the #define is used? The documentation doesn't make this clear. Should suppress coverity issues: 1368525 & 1368527 uninit_use: Using uninitialized value sp. Change-Id: Ibae5e206c4ff47991ea8a11b6b59972b24b71796 Signed-off-by: Martin Roth <martinroth@google.com> Reviewed-on: https://review.coreboot.org/18247 Tested-by: build bot (Jenkins) Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
2017-02-20src/drivers/pc80: Update vga_font_8x16.c to be non-binaryMartin Roth
Previously, the file -i command identified vga_font_8x16.c as application/octet-stream; charset=binary Now it identifies as: text/x-c; charset=us-ascii - Remove non-ascii characters Change-Id: I6b513e6457a31828a6e94c954a7e2e7ee18fd4d6 Signed-off-by: Martin Roth <martinroth@google.com> Reviewed-on: https://review.coreboot.org/18372 Tested-by: build bot (Jenkins) Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
2017-02-20google/eve: Set rise/fall timing values for I2C bus 1Duncan Laurie
Apply the measured rise and fall times for I2C bus 1 on Eve so it can be tuned properly for 400KHz operation. BUG=chrome-os-partner:63020 TEST=verify I2C1 bus speed with a scope Change-Id: I32b5aa460ea35aadca7f3d52324a64880764919f Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: https://review.coreboot.org/18396 Tested-by: build bot (Jenkins) Reviewed-by: Furquan Shaikh <furquan@google.com>
2017-02-20google/eve: Fix FPC supportDuncan Laurie
Currently UART0 GPIOs are being put into native mode during FSP-S stage, so have ramstage re-configure them back to regular GPIO mode. GPP_C8 does not seem to be functioning properly when routed to the APIC, possibly due to the UART0 being enabled even though it is unused, which is required because UART0 is PCI 1e.0 and so must be present for other 1e.x functions to be enumerated. Instead, use this pin as a GPIO interrupt so it will be routed through the GPIO controller at IRQ 14. GPP_C9 was inverted and was only working because the pin was being re-configured in FSP-S. Also export the reset gpio as a device property so it can be used by the kernel driver, which will stop it from complaining at boot. BUG=chrome-os-partner:61233 TEST=verify that the interrupt and device is functional in the OS Change-Id: Iaf9efbf50a13a981c6a9bbd507475777837e9c12 Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: https://review.coreboot.org/18395 Tested-by: build bot (Jenkins) Reviewed-by: Furquan Shaikh <furquan@google.com>
2017-02-19soc/intel/skylake: Disable s0ix if not enabled in devicetreeDuncan Laurie
There is an enable_s0ix config option in the devicetree that should be used to disable it when not set: - do not export C8/C9/C10 C-states in _CST - do not enable SLP_S0 in FSP BUG=chrome-os-partner:58666 TEST=test on eve board to ensure that OS only sees 3 ACPI C-states instead of 6 and that it no longer attempts to enter C10 Change-Id: I90e4dc776d1d17d0b700cda63c8476786cd2e4ff Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: https://review.coreboot.org/18394 Tested-by: build bot (Jenkins) Reviewed-by: Furquan Shaikh <furquan@google.com>
2017-02-19drivers/spi/acpi: Add additional generic ACPI supportDuncan Laurie
Add support for more ACPI features in the generic SPI ACPI driver so it can be flexible enough to support more devices, or devices in different configurations. - add a wake pin - add support for using IRQ GPIO instead of PIRQ - add power resource support with enable and reset gpios BUG=chrome-os-partner:61233 TEST=ensure existing SSDT generation is unchanged, and test that new features generate expected code Change-Id: Ibe37cc87e488004baa2c08a369f73c86e6cd6dce Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: https://review.coreboot.org/18393 Tested-by: build bot (Jenkins) Reviewed-by: Furquan Shaikh <furquan@google.com>
2017-02-19acpi_device: Add macros for GPIO interruptsDuncan Laurie
Add individual macros for the various interrupt types so they can be used in devicetree. BUG=chrome-os-partner:58666 TEST=nothing uses this yet, will be used in an upcoming commit Change-Id: I2a569f60fcc0815835615656b09670987036b848 Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: https://review.coreboot.org/18392 Tested-by: build bot (Jenkins) Reviewed-by: Furquan Shaikh <furquan@google.com>
2017-02-19acpi_device: Move power resource function to generic codeDuncan Laurie
Move the function that adds a power resource block from i2c/generic to the acpi device code at src/arch/x86/acpi_device.c so it can be used by more drivers. BUG=chrome-os-partner:61233 TEST=verify SSDT table generation is unchanged Change-Id: I0ffb61a4f46028cbe912e85c0124d9f5200b9c76 Signed-off-by: Duncan Laurie <dlaurie@chromium.org> Reviewed-on: https://review.coreboot.org/18391 Tested-by: build bot (Jenkins) Reviewed-by: Furquan Shaikh <furquan@google.com>
2017-02-19mb/lenovo/t400: Implement hybrid graphic in romstageArthur Heymans
The hybrid driver select by DRIVERS_LENOVO_HYBRID_GRAPHICS doesn't work for t400/t500. Replace it with a custom romstage implementation. Tested on Lenovo T500 with dual graphics: * Intel Native GFX init * AMD VBios * GNU Linux 4.8.13 * SeaBios as payload * Discrete is working (44 W) * Integrated is working (24 W) * Switchable is working (34 W) ** Both GPUs are enabled, with Intel being connected to the panel ** DRI_PRIME allows to use AMD GPU ** ACPI doesn't seem to work (no vgaswitcheroo) Depends on Change-Id: I4dc00005270240c048272b2e4f52ae46ba1c9422 Depends on Change-Id: If389016f3bb0c4c2fd0b826914997a87a9137201 Change-Id: I7496876e9b434d4a2388e1ede27ac604670339b7 Signed-off-by: Arthur Heymans <arthur@aheymans.xyz> Signed-off-by: Patrick Rudolph <siro@das-labor.org> Reviewed-on: https://review.coreboot.org/18010 Tested-by: build bot (Jenkins) Reviewed-by: Alexander Couzens <lynxis@fe80.eu>
2017-02-18apple/macbook21: Remove unused include `smbios.h`Paul Menzel
Change-Id: I4ed7a164323a71d95a37ea754ec923ca0c5e6219 Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-on: https://review.coreboot.org/18388 Tested-by: build bot (Jenkins) Reviewed-by: Patrick Rudolph <siro@das-labor.org> Reviewed-by: Denis 'GNUtoo' Carikli <GNUtoo@no-log.org>
2017-02-18boardstatus: wiki: Update XiVO's coreboot fork source addressDenis 'GNUtoo' Carikli
This company doesn't do custom hardware anymore and doesn't host the sources anymore. We therefore point to the archived sources instead. Change-Id: I5ce4f6a468b852fc1d0947fe2b28a5297f14c437 Signed-off-by: Denis 'GNUtoo' Carikli <GNUtoo@no-log.org> Reviewed-on: https://review.coreboot.org/11889 Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net> Tested-by: build bot (Jenkins)
2017-02-18soc/intel/skylake: add PrmrrSize to chip configRobbie Zhang
Prmrr configuration is supported by Kabylake FSP-M with UPD provided. It is required as one of the SGX initialization steps in BIOS. BUG=chrome-os-partner:62438 BRANCH=NONE TEST=Tested on Eve, verified uncore PRMRR MSRs get programmed to set size and boot. Change-Id: I2b3dc7c92487505165ee429bd1a37bd60ceac8f3 Signed-off-by: Robbie Zhang <robbie.zhang@intel.com> Reviewed-on: https://review.coreboot.org/18361 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-02-17nb/intel/x4x: Implement resume from S3 suspendArthur Heymans
It rewrites the results of receive enable stored in the upper nvram region, to avoid running receive enable again. Some debug info is also printed about the self-refresh registers. (Not enforcing a reset here, since 0 does not necessarily mean it's not in self-refresh). Change-Id: Ib54bc5c7b0fed6d975ffc31f037b5179d9e5600b Signed-off-by: Arthur Heymans <arthur@aheymans.xyz> Reviewed-on: https://review.coreboot.org/17998 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-02-17nb/intel/x4x: Fix raminit on reset pathArthur Heymans
Previously the raminit failed on hot reset and to work around this issue it unconditionally did a cold reset. This has the following issues: * it's slow; * when the OS issues a hot reset some disk drives expect their 5V power supply to remain on, which gets cut off by a cold reset, causing data corruption. To fix this some steps in raminit must be ommited on the reset path. This includes receive enable calibration. To achieve this it stores receive enable results in RTC nvram for them to be rewritten on the resume path. Note: The same thing needs to be done on the S3 resume path. Calling a hot reset after raminit "outb(0x6, 0cf9)" works. Change-Id: I6601dd90aebd071a0de7cec070487b0f9845bc30 Signed-off-by: Arthur Heymans <arthur@aheymans.xyz> Reviewed-on: https://review.coreboot.org/18009 Tested-by: build bot (Jenkins) Reviewed-by: Nico Huber <nico.h@gmx.de>
2017-02-17soc/intel/skylake: Add Maxim 98927 and Realtek 5663 NHLT blob supportRizwan Qureshi
Add APIs and required parameters for creating Maxim 98927 and Realtek 5336 SSP endpoints in NHLT table. BUG=chrome-os-partner:62051 BRANCH=None TEST=check that NHLT table created is created properly Change-Id: Ica302aab05c5364faf4923dc5327be8e8eaae8b4 Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com> Signed-off-by: Naresh G Solanki <naresh.solanki@intel.com> Signed-off-by: M Naveen <naveen.m@intel.com> Reviewed-on: https://review.coreboot.org/18213 Tested-by: build bot (Jenkins) Reviewed-by: Furquan Shaikh <furquan@google.com>
2017-02-17driver/i2c/max98927: add i2c driver for Maxim 98927 codecRizwan Qureshi
Maxim 98927 kernel driver requires entries in the ACPI SSDT table, add a SSDT generator as part of this driver. BUG=chrome-os-partner:62051 BRANCH=None TEST=After boot, dump and verify that the generated SSDT ACPI table has the required entries. Change-Id: Ic2d4d8449288bc00d085852220b2e1e7a208e9ef Signed-off-by: Naresh G Solanki <naresh.solanki@intel.com> Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com> Signed-off-by: M Naveen <naveen.m@intel.com> Signed-off-by: Dylan Reid <dgreid@chromium.org> Reviewed-on: https://review.coreboot.org/18211 Tested-by: build bot (Jenkins) Reviewed-by: Furquan Shaikh <furquan@google.com>
2017-02-17mainboard/eve: select SOC_INTEL_KABYLAKERizwan Qureshi
eve is based on Kabylake SoC hence select the appropriate config. Change-Id: I756dda5a1924e83a02ac1cebb1907884f436a13f Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com> Reviewed-on: https://review.coreboot.org/18314 Tested-by: build bot (Jenkins) Reviewed-by: Subrata Banik <subrata.banik@intel.com> Reviewed-by: Furquan Shaikh <furquan@google.com>
2017-02-17mainboard/poppy: select SOC_INTEL_KABYLAKERizwan Qureshi
poppy is based on Kabylake SoC hence select the appropriate config. Change-Id: Ie339a3991eeccb8a7dba983a2b5ab5d1c996ce9d Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com> Reviewed-on: https://review.coreboot.org/18313 Tested-by: build bot (Jenkins) Reviewed-by: Furquan Shaikh <furquan@google.com>
2017-02-17soc/intel/skylake: Add config option for KabylakeRizwan Qureshi
Currently there is no distinction between mainboards using Skylake or Kabylake SoC, Add a config option for Kabylake SoC to allow mainboards to explicitly select if they are using it. Change-Id: Ie7960bd81f88a223894afe3115ddc0bc637e4be4 Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com> Reviewed-on: https://review.coreboot.org/18312 Tested-by: build bot (Jenkins) Reviewed-by: Furquan Shaikh <furquan@google.com> Reviewed-by: Martin Roth <martinroth@google.com>
2017-02-17grub: Build module `boottime`Paul Menzel
Configure GRUB to build with boot time statistics. That allows users to add that module to GRUB by adding `boottime` to the list of extra modules. Change-Id: I76a07e49aecb37652fe8c7d6a9421fd464424287 Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de> Reviewed-on: https://review.coreboot.org/18367 Tested-by: build bot (Jenkins) Reviewed-by: Patrick Rudolph <siro@das-labor.org>
2017-02-17libpayload: multiboot - support meminfo flagMathias Krause
Some simple implementation of the MultiBoot protocol may not pass a memory map (MULTIBOOT_FLAGS_MMAP missing in the flags) but just the two values for low and high memory, indicated by the MULTIBOOT_FLAGS_MEMINFO flag. Support those kind of boot loaders too, instead of falling back to the hard-coded values in lib_get_sysinfo(). Tested with a multiboot enhanced version of FILO. Change-Id: I22cf9e3ec0075aff040390bd177c5cd22d439b81 Signed-off-by: Mathias Krause <minipli@googlemail.com> Reviewed-on: https://review.coreboot.org/18350 Tested-by: build bot (Jenkins) Reviewed-by: Nico Huber <nico.h@gmx.de>
2017-02-17intel/skylake: add function is_secondary_thread()Robbie Zhang
There are MSRs that are programmable per-core not per-thread, so add a function to check whether current executing CPU is a primary core or a "hyperthreaded"/secondary core. For instance when trying to program Core PRMRR MSRs(per-core) with mp_init, cpu exception is thrown from the secondary thread. This function was used to avoid that. Potentially this function can be put to common code or arch/x86 or cpu/x86. BUG=chrome-os-partner:62438 BRANCH=NONE TEST=Tested on Eve, verified core PRMRR MSRs get programmed only on primary thread avoiding exeception. Change-Id: Ic9648351fadf912164a39206788859baf3e5c173 Signed-off-by: Robbie Zhang <robbie.zhang@intel.com> Reviewed-on: https://review.coreboot.org/18366 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-02-17libpayload: x86/head - implement argc/argv handlingMathias Krause
Implement the argc/argv passing as described in coreboot’s payload API: http://www.coreboot.org/Payload_API While at it, give the code some love by not needlessly trashing register values. Change-Id: Ib830f2c67b631b7216843203cefd55d9bb780d83 Signed-off-by: Mathias Krause <minipli@googlemail.com> Reviewed-on: https://review.coreboot.org/18336 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Tested-by: build bot (Jenkins)
2017-02-17libpayload: x86/exec - simplify and robustify the codeMathias Krause
Simplify the code by directly using the arguments on the stack as base pointer relative memory references, instead of loading them into intermediate registers first. Make it more robust by preserving all callee saved registers mandated by the C calling convention (and only those), namely EBP, EBX, ESI and EDI. Don't assume anything about the register state when the called function returns -- beside the segment registers and the stack pointer to be still the same as before the call. Change-Id: I383d6ccefc5b3d5cca37a1c9b638c231bbc48aa8 Signed-off-by: Mathias Krause <minipli@googlemail.com> Reviewed-on: https://review.coreboot.org/18335 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Tested-by: build bot (Jenkins)
2017-02-17libpayload: x86/main - propagate return value of main()Mathias Krause
According to coreboot’s payload API [1], the called payload should be able to return a value via %eax. Support this by changing the prototype of start_main() and pass on the return value of main() to the caller instead of discarding it. [1] https://www.coreboot.org/Payload_API Change-Id: I8442faea19cc8e04487092f8e61aa4e5cba3ba76 Signed-off-by: Mathias Krause <minipli@googlemail.com> Reviewed-on: https://review.coreboot.org/18334 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-02-17libpayload: x86/exec - fix argc/argv value passingMathias Krause
According to coreboot’s payload API [1] the argc value should be passed at stack offset 0x10, so we need to push a dummy value to comply to the API. [1] https://www.coreboot.org/Payload_API Change-Id: Id20424185a5bf7e4d94de1886a2cece3f3968371 Signed-off-by: Mathias Krause <minipli@googlemail.com> Reviewed-on: https://review.coreboot.org/18333 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-02-17mainboard/google/poppy: Generate digitizer node in SSDTFurquan Shaikh
Add support for generating digitizer node in SSDT using wacom i2c driver. BUG=None BRANCH=None TEST=Verified that the node shows up in SSDT. Change-Id: If7e1e2463778c2ff7263eff995def149457edcde Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/18373 Tested-by: build bot (Jenkins) Reviewed-by: Aaron Durbin <adurbin@chromium.org>
2017-02-16mainboard/google/eve: Generate FPC device using SPI SSDT generatorFurquan Shaikh
Use the newly added SPI SSDT generator for adding FPC device. BUG=chrome-os-partner:59832 BRANCH=None TEST=Compiles successfully. Verified that the SSDT entry matches the entry in mainboard.asl Change-Id: I1b3c33f2b4337735a9725dd4eb6193b2455962d7 Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/18343 Tested-by: build bot (Jenkins) Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
2017-02-16drivers/spi: Add support for generating SPI device in SSDTFurquan Shaikh
Similar to I2C driver, add support for generating SPI device and required properties in SSDT for ACPI. BUG=chrome-os-partner:59832 BRANCH=None TEST=Compiles succesfully. Verified SPI device generated in SSDT on poppy. Change-Id: Ic4da79c823131d54d9eb3652b86f6e40fe643ab5 Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/18342 Tested-by: build bot (Jenkins) Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
2017-02-16soc/intel/skylake: Add support for SPI deviceFurquan Shaikh
Add a new PCI driver for SPI devices with supported PCI ids. Also, provide a translation table to convert struct device structure into SPI bus number. BUG=chrome-os-partner:59832 BRANCH=None TEST=Compiles successfully Change-Id: If860eb819f2ce5ae5443f808b356af57f86c52be Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/18341 Tested-by: build bot (Jenkins) Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
2017-02-16device: Add scan_generic_bus supportFurquan Shaikh
scan_smbus routine does not perform any smbus specific operation. Thus, rename the routine to scan_generic_bus so that it can be used by other buses like SPI. Add a wrapper scan_smbus to allow other users of smbus scan to continue working as before. BUG=chrome-os-partner:59832 BRANCH=None TEST=Compiles successfully Change-Id: I8ca1a2b7f2906d186ec39e9223ce18b8a1f27196 Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/18363 Reviewed-by: Aaron Durbin <adurbin@chromium.org> Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
2017-02-16device: Add a new "SPI" device typeFurquan Shaikh
Add support for a new "SPI" device type in the devicetree to bind a device on the SPI bus. Allow device to provide chip select number for the device as a parameter. Add spi_bus_operations with operation dev_to_bus which allows SoCs to define a translation method for converting "struct device" into a unique SPI bus number. BUG=chrome-os-partner:59832 BRANCH=None TEST=Compiles successfully. Change-Id: I86f09516d3cddd619fef23a4659c9e4eadbcf3fa Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/18340 Reviewed-by: Duncan Laurie <dlaurie@chromium.org> Tested-by: build bot (Jenkins)
2017-02-16sconfig: Add a new "SPI" device typeFurquan Shaikh
Update sconfig lex and yacc files to add support for a new "SPI" device type in the devicetree. SPI device takes only parameter i.e. chip select number for the device on the SPI bus. Re-generate the shipped files for sconfig using flex 2.6.0 and bison 3.0.4 (make CONFIG_SCONFIG_GENPARSER=1). Clean up local paths that leak into generated files. BUG=chrome-os-partner:59832 BRANCH=None TEST=Compiles successfully. Change-Id: If0831e25b3e4ed87827ad92356d7bf47b6387884 Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/18339 Tested-by: build bot (Jenkins) Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
2017-02-16soc/intel/skylake: Add GSPI controller get_config supportFurquan Shaikh
Provide implementation of get_config routine for GSPI controller on skylake platforms. BUG=chrome-os-partner:59832 BRANCH=None TEST=Compiles successfully. Change-Id: I5170076c15d72a7f29acd0989acef5b9149e2ba0 Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/18338 Tested-by: build bot (Jenkins) Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
2017-02-16spi: Add function callback to get configuration of SPI busFurquan Shaikh
Add a new callback to spi_ctrlr structure - get_config - to obtain configuration of SPI bus from the controller driver. Also, move common config definitions from acpi_device.h to spi-generic.h BUG=chrome-os-partner:59832 BRANCH=None TEST=Compiles successfully Change-Id: I412c8c70167d18058a32041c2310bc1c884043ce Signed-off-by: Furquan Shaikh <furquan@chromium.org> Reviewed-on: https://review.coreboot.org/18337 Tested-by: build bot (Jenkins) Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net> Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-17 08:03:57 +0000