| Age | Commit message (Collapse) | Author |
|---|
|
Change-Id: I97920e7eb64c05034184f9a4e1c8f2dfa44d3fdd
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Reviewed-on: http://review.coreboot.org/9813
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
If the board is configured with a pre-graphics delay it should
be skipped in the resume path.
BUG=chrome-os-partner:28234
BRANCH=broadwell
TEST=measure resume time in dev mode to be same as normal mode
Change-Id: I5a4ad5bba9e5316c89f7935d8811759b041429d9
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: b44a7167532410fc44ca9df1c91c91aaf541ae49
Original-Change-Id: Ic9f2cda71d8a567f57e863409f0f3fb98ab68bcf
Original-Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/245116
Original-Reviewed-by: Shawn N <shawnn@chromium.org>
Reviewed-on: http://review.coreboot.org/9812
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
This patch fixes the use of the recovery button, and the value is stored
in a SATA controller scratch register.
BUG=chrome-os-partner:35241
BRANCH=none
TEST=Use recovery button and run firmware_RecoveryButton
Change-Id: Ia06f147c7e44d6c4eea2c2e4f502c233c956ee9b
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 34c7ee922a9602b3448a72cd669fd68feeed1bba
Original-Change-Id: I1667c7f188b0f87c4bc7caa82f9c977b2b4c0611
Original-Signed-off-by: Ryan Lin <ryan.lin@intel.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/241772
Original-Reviewed-by: Shawn N <shawnn@chromium.org>
Reviewed-on: http://review.coreboot.org/9811
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
This is a no-op change just sorting the CBMEM entries' definitions for
easy look up and comparison.
BRANCH=storm
BUG=none
TEST=Booted a storm device, observed the expected CBMEM entries
present in the console output.
Change-Id: I26365285f20ecb256918277b60e178cd61dc8213
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: f140fd8d85ded30d1b89f5d4c64f8b9f31d6b27b
Original-Change-Id: Ibcd4f184ef1bade10ad677384f61243da7e3c713
Original-Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/225259
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/9810
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Edward O'Callaghan <edward.ocallaghan@koparo.com>
|
|
Urara uses SPFI interface 1 and Winbond SPI NOR flash.
BRANCH=none
BUG=chrome-os-partner:31438
TEST=with the fix of the Winbond driver (next patch) the bootblock
successfully probes the Windbond device on the FPGA board.
Console log below:
coreboot-4.0 bootblock Tue Nov 11 07:05:48 PST 2014 starting...
SF: Detected W25Q16 with page size 1000, total 200000
Change-Id: Ia848eac5b4a94bf95297c928b5447463c90d89eb
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 38386715c52526edbe9ad356945849e21799fd94
Original-Change-Id: Ic27b60adc26bf244e7a15b5257e94df4b9d88249
Original-Signed-off-by: Ionela Voinescu <ionela.voinescu@imgtec.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/229030
Original-Reviewed-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: http://review.coreboot.org/9809
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
This was added in upstream but not in Chromium OS where
pistachio support was developed.
Change-Id: I54f883776f19aa7bd357841731166e92d03145d8
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Reviewed-on: http://review.coreboot.org/9808
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Board boots to linux. VGA works with rom.
Change-Id: I96b73a90c3d88672f0d238f4b735cd2f96ef99bd
Signed-off-by: Damien Zammit <damien@zamaudio.com>
Reviewed-on: http://review.coreboot.org/9803
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <edward.ocallaghan@koparo.com>
|
|
Change-Id: I3375c21d5d4aed30d5641629c44d6a5885efee11
Signed-off-by: Damien Zammit <damien@zamaudio.com>
Reviewed-on: http://review.coreboot.org/9807
Reviewed-by: Edward O'Callaghan <edward.ocallaghan@koparo.com>
Tested-by: build bot (Jenkins)
|
|
Tested on T530, T430s.
Verified with lspci dump.
Change-Id: I45acadb0c55534a67f7ad3e7bd84f4482a4344d7
Signed-off-by: Nicolas Reinecke <nr@das-labor.org>
Reviewed-on: http://review.coreboot.org/9451
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <edward.ocallaghan@koparo.com>
|
|
Change-Id: I9a40e5a1028c7674e6dd54742e6646ba48ce7696
Signed-off-by: Nicolas Reinecke <nr@das-labor.org>
Reviewed-on: http://review.coreboot.org/9449
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <edward.ocallaghan@koparo.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Change-Id: Ibc7fe38ae11e9d477f85fdcf760b27abc6013f94
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: http://review.coreboot.org/9791
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Some upstreaming patches missed that, so follow up.
Change-Id: I28665c97ac777d8b0b0f909e64b32681ed2b98f7
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Reviewed-on: http://review.coreboot.org/9771
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
|
|
BUG=chrome-os-partner:35807
BRANCH=broadcom-firmware
TEST=booted b0 board. messages printed on console:
coreboot-bcf5dc0-dirty bootblock Mon Feb 9 13:33:55 PST 2015 starting...
Exception handlers installed.
Change-Id: I271ead2f4fe48b809fd311acd5a27a675dce549e
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: ddff8fb170e775a121150fce065410d2925ad18c
Original-Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org>
Original-Change-Id: Ia6e82fa89547d61745c1473f723897dc3c1296ef
Original-Reviewed-on: https://chromium-review.googlesource.com/251301
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: http://review.coreboot.org/9765
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <edward.ocallaghan@koparo.com>
|
|
BUG=chrome-os-partner:35807
BRANCH=broadcom-firmware
TEST=none
Change-Id: I40623e92f290e5c584a451d99071316b6fc35431
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 505720f734da7a4cdfaff8b2531385644141ba83
Original-Change-Id: I655c7065047971ab05a13e90ab911d7464a37552
Original-Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/251300
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: http://review.coreboot.org/9764
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <edward.ocallaghan@koparo.com>
|
|
ChromeOS/vboot devices expect the TPM PCRs 0 and 1 to be extended with
digests that attest the chosen boot mode (developer/recovery) and the
HWID in a secure way. This patch uses the newly added vboot2 support
functions to fetch these digests and store them in the TPM.
CQ-DEPEND=CL:244542
BRANCH=veyron
BUG=chromium:451609
TEST=Booted Jerry. Confirmed that PCR0 contains the same value as on my
vboot1 Blaze and Falco (and PCR1 contains some non-zero hash).
Original-Change-Id: I7037b8198c09fccee5440c4c85f0821166784cec
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/245119
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Original-Reviewed-by: Daisuke Nojiri <dnojiri@chromium.org>
(cherry picked from commit 8b44e13098cb7493091f2ce6c4ab423f2cbf0177)
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Change-Id: I549de8c07353683633fbf73e4ee62ba0ed72ff89
Reviewed-on: http://review.coreboot.org/9706
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
BUG=chromium:452179
BRANCH=ToT
CQ-DEPEND=CL:243362
TEST=manual
emerge-veyron_pinky coreboot
Original-Change-Id: Ibcbaea2990e5e06ea7cfaaa5412ef7c1477f5fcc
Original-Signed-off-by: Bill Richardson <wfrichar@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/243380
Original-Reviewed-by: Randall Spangler <rspangler@chromium.org>
(cherry picked from commit 8e5c18eeb21944bdcb064b4491c6781d16ef5608)
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Change-Id: I26f6fb67655cb1dfbdcdc48530ef6bfeb1aa692a
Reviewed-on: http://review.coreboot.org/9705
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
The ramstage is loaded from romstage, so the LZMA scratchpad buffer used
to decompress it is part of the romstage BSS in SRAM. On RK3288, SRAM
cannot be cached which makes the decompression so slow that it's faster
to just load an uncompressed image from SPI. Disable ramstage
compression on this SoC to account for that.
[pg: implementation avoids restructuring all of Kconfig]
BRANCH=None
BUG=None
TEST=Built for Pinky and Falco, confirmed that the former didn't have
COMPRESS_RAMSTAGE in its .config and the latter still did. Measured a
speed-up of about 35ms on Pinky. (For some weird reason, the
decompression of the payload also takes way longer than on other
platforms, although not as long as the ramstage. I have no explanation
for that and can't really think of a good way to figure it out... maybe
the Cortex-A12 is just terrible at some operation that LZMA uses a lot?)
Change-Id: I9f67f7537696ec09496483b16b59a8b73f4cb11b
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/234192
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Reviewed-on: http://review.coreboot.org/9792
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Change-Id: I62674ccfb836fb0b02ac562f678cdfa44be98ae3
Signed-off-by: Nicolas Reinecke <nr@das-labor.org>
Reviewed-on: http://review.coreboot.org/9779
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <edward.ocallaghan@koparo.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
We recently restructured where the CBFS header is stored
and how it is looked up, with less magic. The RISC-V port
didn't get the memo, so have it follow the pack now.
Change-Id: Ic27e3e7f9acd55027e357f2c4beddf960ea02c4d
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/9795
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
|
|
When CONFIG_MULTIPLE_CBFS_INSTANCES is enabled, the image is expected
to have CBFS instances in rw-a and rw-b sections of the bootrom.
This patch adds code which makes sure that CBFS header points at the
proper bootrpom section as determined by vboot, and the RW stages load
from that section.
BRANCH=storm
BUG=chrome-os-partner:34161, chromium:445938
TEST=with the rest of the patches in, STORM boots all the way into
Linux login prompt.
Original-Change-Id: I187e3d3e65d548c672fdf3b42419544d3bd11ea1
Original-Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/237662
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
(cherry picked from commit 71ad0bb41b183374a84a5b9fb92c3afd813ceace)
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Change-Id: Ia05cb713981c44da8cb379b72dfbe17fe1f6c5ff
Reviewed-on: http://review.coreboot.org/9704
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
This patch aligns our verstage code to the new API addition in vboot2.
The hardware crypto functions are stubbed out by default and just
pretend that all algorithms are unsupported, causing vboot to fall back
to the normal software hashing code. These weak symbols can be
overridden by individual platform code to provide actual hardware
crypto engine support.
CQ-DEPEND=CL:236453
BRANCH=None
BUG=chrome-os-partner:32987
TEST=Booted Pinky, confirmed vboot falls back to software crypto.
Original-Change-Id: Idf6a38febd163aa2bff6e9a0e207213f01ca8324
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/236435
Original-Reviewed-by: Randall Spangler <rspangler@chromium.org>
(cherry picked from commit 9b5ee7f575f1aa3b0eb6ef78947ca93a4818f57b)
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Change-Id: I6f0e19255a9bc5c5cd1767db76f1e47897ef0798
Reviewed-on: http://review.coreboot.org/9703
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
this allows each board to decide what to do after firmware verification is
done. some board needs to return back to the previous stage and let the
previous stage kick off the verified stage.
this also makes it more visible what is going to happen in the verstage since
stage_exit now resides in main().
BUG=none
BRANCH=tot
TEST=booted cosmos dev board. booted blaze in normal and recovery mode.
built for all current boards.
Original-Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org>
Original-Change-Id: I3cb466cedf2a9c2b0d48fc4b0f73f76d0714c0c7
Original-Reviewed-on: https://chromium-review.googlesource.com/232517
(cherry picked from commit 495704f36aa54ba12231d396376f01289d083f58)
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Change-Id: Ic20dfd3fa93849befc2b37012a5e0907fe83e8e2
Reviewed-on: http://review.coreboot.org/9702
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
The ipq806x UART is based on the same universal serial port which can
be also configured as i2c or SPI. Configuring it is not a trivial
task, so in case the kernel wants to use earlyprintk() the port needs
to be configured by the firmware.
Invoking uart_init() when the console is not enabled causes include
file collisions, which would require changes to more than 100 files.
Leaving this to another day, rearranging the ipq806x driver to be able
to invoke UART initialization function even when serial console is not
configured.
Also add a check to avoid initialization if UART has been already
set up.
BRANCH=storm
BUG=chrome-os-partner:35364
TEST=verified that storm console is still fully operational when
enabled, and that the kernel boots fine to the serial console
login prompt even if the firmware console is disabled.
Change-Id: Ibbbab875449f2ac2f0d6c504c18faf0da8251ffa
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: c512d6c1d0c0868137d1213ea84cd4bca58872db
Original-Change-Id: I421acba3edf398d960b5058f15d1abb80ebc7660
Original-Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/240516
Original-Reviewed-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/9794
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Originally ported QCA UART driver used hardware accessor macros where
both address and data were represented by 32 bit integers. Coreboot
uses macros where addresses are represented by pointers, this make the
code more robust, as accidental swap between address and data does not
go unnoticed.
This patch converts ipq806x UART driver to use coreboot accessors. It
relies on gcc void pointer arithmetic considering objects pointed at
by void pointers to be one byte in size. Also replacing spaces with
hard tabs where appropriate.
BRANCH=storm
BUG=chrome-os-partner:34790
TEST=new code still boots fine on Storm with console output present.
Change-Id: I3ded9c338ff241bb1d839994f7296756aad8772d
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 10616351704ebbcfcf25793ae974b256bc5bd6b0
Original-Change-Id: Ie15e09f9f3ea10a8566b6845219c2e09fed39218
Original-Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/240514
Original-Reviewed-by: David Hendricks <dhendrix@chromium.org>
Original-Reviewed-by: Trevor Bourget <tbourget@codeaurora.org>
Reviewed-on: http://review.coreboot.org/9793
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
This is done via a PCODE mailbox write.
BUG=chrome-os-partner:37043
BRANCH=broadwell
TEST=build and boot on samus
Change-Id: I95e8fe3e28eec76d6b5b488a0c770c04f408700e
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: b90bef7f708b1ce83f6e124f4b38ae51ec6b0597
Original-Change-Id: I95cd4c17db672a53ba05f85ba5fa7bc866af1543
Original-Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/252862
Original-Reviewed-by: Alec Berg <alecaberg@chromium.org>
Original-Reviewed-by: Shawn N <shawnn@chromium.org>
(cherry picked from commit ab6b4bddf3365713aa40d194c2dbd3e59985f00d)
Original-Reviewed-on: https://chromium-review.googlesource.com/252883
Reviewed-on: http://review.coreboot.org/9783
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
To avoid entries with Type-C alternate mode devices disable
compliance mode entry. This needs to be set on both boot
and resume.
BUG=chrome-os-partner:35320
BRANCH=samus
TEST=manual:
1) boot on samus with USB keyboard plugged in -> controller in D0 at boot
2) iotools mmio_read32 0xe12080ec == 0x18010c01
3) suspend and resume
4) iotools mmio_read32 0xe12080ec == 0x18010c01
5) remove USB keyboard -> controller in D3
6) iotools mmio_read32 0xe12080ec == 0xffffffff
7) plug in USB keyboard -> controller in D0
8) iotools mmio_read32 0xe12080ec == 0x18010c01
9) boot with no external USB devices -> controller in D3 at boot
10) iotools mmio_read32 0xe12080ec == 0xffffffff
11) plug in USB keyboard -> controller in D0
12) iotools mmio_read32 0xe12080ec == 0x18010c01
Change-Id: I4d566112b3c188bafdf9a4bbd92944c89500e3e8
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: db8c8ab8ff25f6a39cd50dcc91b5ba9fd7d05059
Original-Change-Id: I8b68ba75e254a7e236c869f4470207eb5290053d
Original-Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/251361
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: http://review.coreboot.org/9782
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
BUG=None
BRANCH=None
TEST=Compiles and boots to "starting kernel" on panther
Change-Id: Ic71aea6d8939a4fa3cd890e2048fff22ea25d186
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 4b5515bd00b76332748e4181cdf984c98a83993a
Original-Change-Id: I2f890871ad7cddaf132a0fa59a93f05c51d0c00e
Original-Signed-off-by: Furquan Shaikh <furquan@google.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/234982
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Original-Tested-by: Furquan Shaikh <furquan@chromium.org>
Original-Commit-Queue: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: http://review.coreboot.org/9781
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
The following changes were made:
- order commands and options definitions alphabetically
- do not report errors at cbfs_image_from_file() call sites - the
error is reported by the function itself
- remove the unused parameter in cbfs_create_empty_entry() prototype
BRANCH=storm
BUG=none
TEST=compiled cbfstool, built a storm image, observed that the image
still boots
Change-Id: I31b15fab0a63749c6f2d351901ed545de531eb39
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: a909a50e03be77f972b1a497198fe758661aa9f8
Original-Change-Id: I4b8898dbd44eeb2c6b388a485366e4e22b1bed16
Original-Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/237560
Original-Reviewed-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/9746
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
The previous patch introduced a bug where the new added case statement
was missing the break. There was no problem testing, because an
unrelated parameter structure field was being modified as a result.
BRANCH=storm
BUG=none
TEST=compiles and runs
Change-Id: Iaeb328048f61ffd57057ebce47f2ac8e00fc5aac
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 27ecc130569e4252e4627052f617130a2017c645
Original-Change-Id: Ib3e6c4c2b5c37588c612b8ab2672f6845c1b4ecb
Original-Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/239598
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: http://review.coreboot.org/9743
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Edward O'Callaghan <edward.ocallaghan@koparo.com>
|
|
The new command allows to create a file where the original CBFS image
is duplicated at a different offset.
The required options of the new command are -D, the offset where the
copy CBFS header is placed, and -s, the size of the new CBFS copy.
When a CBFS is copied, the bootblock area of the source CBFS is
ignored, as well as empty and deleted files in the source CBFS. The
size of the destination CBFS is calculated as the rombase size of the
source CBFS less the bootblock size.
The copy instance can be created in the image only above the original,
which rules out the use of this new command for x86 images. If
necessary, this limitation could be addressed later.
As with other cbfstool commands, unless explicitly specified the
lowest CBFS instance in the image is considered the source. If
necessary, the user can specify the source CBFS using the -H option.
BRANCH=storm
BUG=chrome-os-partner:34161, chromium:445938
TEST=run multiple cbfstool commands on a storm image:
$ cd /tmp
$ cp /build/storm/firmware/image.serial.bin storm.bin
$ cbfstool storm.bin print
storm.bin: 8192 kB, bootblocksize 34472, romsize 458752, offset 0x8700
alignment: 64 bytes, architecture: arm
Name Offset Type Size
cdt.mbn 0x8700 raw 416
ddr.mbn 0x8900 raw 25836
rpm.mbn 0xee40 raw 78576
tz.mbn 0x22180 raw 85360
fallback/verstage 0x36f40 stage 41620
fallback/romstage 0x41240 stage 19556
fallback/ramstage 0x45f00 stage 25579
config 0x4c340 raw 2878
fallback/payload 0x4cec0 payload 64811
u-boot.dtb 0x5cc40 (unknown) 2993
(empty) 0x5d840 null 75608
$ cbfstool storm.bin copy -D 0x420000
E: You need to specify -s/--size.
$ cbfstool storm.bin copy -D 0x420000 -s 0x70000
$ cbfstool storm.bin print
W: Multiple (2) CBFS headers found, using the first one.
storm.bin: 8192 kB, bootblocksize 34472, romsize 458752, offset 0x8700
alignment: 64 bytes, architecture: arm
Name Offset Type Size
cdt.mbn 0x8700 raw 416
ddr.mbn 0x8900 raw 25836
rpm.mbn 0xee40 raw 78576
tz.mbn 0x22180 raw 85360
fallback/verstage 0x36f40 stage 41620
fallback/romstage 0x41240 stage 19556
fallback/ramstage 0x45f00 stage 25579
config 0x4c340 raw 2878
fallback/payload 0x4cec0 payload 64811
u-boot.dtb 0x5cc40 (unknown) 2993
(empty) 0x5d840 null 75608
cbfstool storm.bin print -H 0x420000
storm.bin: 8192 kB, bootblocksize 0, romsize 4784128, offset 0x420040
alignment: 64 bytes, architecture: arm
Name Offset Type Size
cdt.mbn 0x420040 raw 416
ddr.mbn 0x420240 raw 25836
rpm.mbn 0x426780 raw 78576
tz.mbn 0x439ac0 raw 85360
fallback/verstage 0x44e880 stage 41620
fallback/romstage 0x458b80 stage 19556
fallback/ramstage 0x45d840 stage 25579
config 0x463c80 raw 2878
fallback/payload 0x464800 payload 64811
u-boot.dtb 0x474580 (unknown) 2993
(empty) 0x475180 null 110168
$ cbfstool storm.bin remove -n config -H 0x420000
$ cbfstool storm.bin copy -H 0x420000 -D 0x620000 -s 0x70000
$ cbfstool storm.bin print -H 0x620000
storm.bin: 8192 kB, bootblocksize 0, romsize 6881280, offset 0x620040
alignment: 64 bytes, architecture: arm
Name Offset Type Size
cdt.mbn 0x620040 raw 416
ddr.mbn 0x620240 raw 25836
rpm.mbn 0x626780 raw 78576
tz.mbn 0x639ac0 raw 85360
fallback/verstage 0x64e880 stage 41620
fallback/romstage 0x658b80 stage 19556
fallback/ramstage 0x65d840 stage 25579
fallback/payload 0x663c80 payload 64811
u-boot.dtb 0x673a00 (unknown) 2993
(empty) 0x674600 null 113112
$ cbfstool /build/storm/firmware/image.serial.bin extract -n fallback/payload -f payload1
[..]
$ cbfstool storm.bin extract -H 0x620000 -n fallback/payload -f payload2
[..]
$ diff payload1 payload2
Change-Id: Ieb9205848aec361bb870de0d284dff06c597564f
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: b8d3c1b09a47ca24d2d2effc6de0e89d1b0a8903
Original-Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Original-Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Original-Change-Id: I227e607ccf7a9a8e2a1f3c6bbc506b8d29a35b1b
Original-Reviewed-on: https://chromium-review.googlesource.com/237561
Reviewed-on: http://review.coreboot.org/9742
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
There potentially could be multiple CBFS instances present in the
firmware image. cbfstool should be able to operate on any of them, not
just the first one present.
To accomplish that, allow all CBFS commands to accept the -H parameter
(which specifies the exact CBFS header location in the image).
If this parameter is specified, the image is not searched for the CBFS
header, only the specified location is checked for validity, If the
location is valid, it is considered to be the CBFS header, if not -
the tool exits with an error status.
Note, that default behavior of the tool does not change.
BRANCH=storm
BUG=chrome-os-partner:34161, chromium:445938
TEST=run the following experiments:
- examined an image with three CBFS instances, was able to print all
of them.
- built a rambi coreboot image and tried the following (cbfstool output abbreviated):
$ ./util/cbfstool/cbfstool /build/rambi/firmware/coreboot.rom print
coreboot.rom: 8192 kB, bootblocksize 2448, romsize 8388608, offset 0x700000
alignment: 64 bytes, architecture: x86
Name Offset Type Size
cmos_layout.bin 0x700000 cmos_layout 1164
...
(empty) 0x7ec600 null 77848
$ \od -tx4 -Ax /build/rambi/firmware/coreboot.rom | tail -2
7ffff0 fff67de9 000000ff fff6dfe9 fffff650
800000
$ ./util/cbfstool/cbfstool /build/rambi/firmware/coreboot.rom print -H 0x7ff650
coreboot.rom: 8192 kB, bootblocksize 2448, romsize 8388608, offset 0x700000
alignment: 64 bytes, architecture: x86
Name Offset Type Size
cmos_layout.bin 0x700000 cmos_layout 1164
...
(empty) 0x7ec600 null 77848
$ ./util/cbfstool/cbfstool /build/rambi/firmware/coreboot.rom print -H 0x7ff654
E: /build/rambi/firmware/coreboot.rom does not have CBFS master header.
E: Could not load ROM image '/build/rambi/firmware/coreboot.rom'.
$
Change-Id: I64cbdc79096f3c7a113762b641305542af7bbd60
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 86b88222df6eed25bb176d653305e2e57e18b73a
Original-Change-Id: I486092e222c96c65868ae7d41a9e8976ffcc93c4
Original-Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/237485
Original-Reviewed-by: David Hendricks <dhendrix@chromium.org>
Original-Reviewed-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Reviewed-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/9741
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Move reset support into the Intel common branch. Prevent breaking of
existing platforms by using a Kconfig value to select use of the common
reset code.
BRANCH=none
BUG=None
TEST=Build and run on Glados
Change-Id: I5ba86ef585dde3ef4ecdcc198ab615b5c056d985
Signed-off-by: Stefan Reinauer <reinauer@chromium.org>
Original-Commit-Id: 85d8a6d9628a66cc8d73176d460cd6c5bf6bd6b2
Original-Change-Id: I5048ccf3eb593d59301ad8e808c4e281b9a0aa98
Original-Signed-off-by: Lee Leahy <Leroy.P.Leahy@intel.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/248301
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Original-Commit-Queue: Leroy P Leahy <leroy.p.leahy@intel.com>
Original-Tested-by: Leroy P Leahy <leroy.p.leahy@intel.com>
Reviewed-on: http://review.coreboot.org/9505
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Add support for applying write protection to the MRC cache
region in SPI flash.
This is only enabled if there is write protect GPIO that is
set, and the flash status register reports that the flash
chip is currently write protected.
Then it will call out to a SOC specific function that will
enable write protection on the RW_MRC_CACHE region of flash.
The implementation is not quite as clean as I would like because
there is not a common flash protect interface across SOCs so
instead it relies on a new Kconfig variable to be set that will
indicate a SOC implements the function to protect a region of
SPI flash.
BUG=chrome-os-partner:28234
BRANCH=broadwell
TEST=build and boot on samus
1) with either WPSW=0 or SRP0=0 the PRR is not applied
2) with both WPSW=1 and SRP0=1 the PRR is applied
Change-Id: If5907b7ddf3f966c546ae32dc99aa815beb27587
Signed-off-by: Stefan Reinauer <reinauer@chromium.org>
Original-Commit-Id: a3e0e71dfd7339aab171a26b67aec465a3f332d6
Original-Change-Id: I94e54e4723b1dcdacbb6a05f047d0c0ebc7d8711
Original-Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/241170
Original-Reviewed-by: Shawn N <shawnn@chromium.org>
Reviewed-on: http://review.coreboot.org/9494
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Serial port on ITE 8772 SuperIO must be initialized before
console_init is called. So the pre console init callback
is added to let mainboard code do proper initialization.
Change-Id: Iaa3e4b9c6e7ce77a7b9a6b9ecedd8ea54f3141dc
Signed-off-by: Stefan Reinauer <reinauer@chromium.org>
Original-Commit-Id: 71ee2fd470e19fa4854f895678445b05c17761c1
Original-Change-Id: I594e6e4a72f65744deca5cad666eb3b227adeb24
Original-Signed-off-by: Wenkai Du <wenkai.du@intel.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/227933
Original-Reviewed-by: Kenji Chen <kenji.chen@intel.com>
Original-Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Original-Reviewed-by: Rajmohan Mani <rajmohan.mani@intel.com>
Original-Reviewed-by: Shawn Nematbakhsh <shawnn@chromium.org>
Reviewed-on: http://review.coreboot.org/9472
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
I doubt anybody will ask for the configuration and request that
0 bytes be returned, but AFAICS that's legal, so let's support it.
Should have no effect on ChipIdea since it knows not to send more
data than requested by the host.
BRANCH=none
BUG=none
TEST=none
Change-Id: Ibfe57b593015fa5e0381c45ff9e39c3f912b4d4d
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 45555e929d9d07dbb58ecfd18333f26375a0e3d7
Original-Change-Id: I7432772a1812c6f52c2b1688ee4c6f67d02ccf28
Original-Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/258064
Original-Reviewed-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: http://review.coreboot.org/9790
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Only set internal variables when there's no risk of breaking things.
BRANCH=none
BUG=none
TEST=none
Change-Id: I8a8b63f60bdb70fad38130ce38eef81fe3725aa2
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 7119829096b444b790937b116fb782bcb5da70cd
Original-Change-Id: If698b11a7ff7688def310d8574fcfa7a40f703c1
Original-Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/258063
Original-Reviewed-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: http://review.coreboot.org/9789
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
First handle IN packets, then OUT packets and finally SETUP packets.
This makes OS X happy. It isn't implemented as the data sheet recommends
but it avoids implementing a state machine and should always produce
observable effects identical to that of the stateful solution.
BRANCH=none
BUG=none
TEST=`fastboot getvar version` on OSX works
Change-Id: Ic7b27387771d6a7794fba12fc822fccc48770ea8
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: f0e59547519d50b1d34f6abdc6132330125f94f3
Original-Change-Id: Iada1cff011f11e7d5cb1a1b34896ab590f488ec7
Original-Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/258062
Original-Reviewed-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: http://review.coreboot.org/9788
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Mark EP0 non-stall explicitly. Shouldn't be necessary, but
won't hurt either.
BRANCH=none
BUG=none
TEST=none
Change-Id: I7ecd16a2affe064918d93436aedfa07bd9a1cf56
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: a0fc237b33444fc30dc5b62e4f1afc3188f2cf43
Original-Change-Id: I1aa8742eebc4de733317600e35627631ebaf4724
Original-Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/258061
Original-Reviewed-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: http://review.coreboot.org/9787
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Trivial copy & paste error, likely with no visible effect so far.
BRANCH=none
BUG=none
TEST=none
Change-Id: Ieaf5e770ab7a8474e407012d2c11a15c46ab357d
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 90f8971500c95456ae70c6f4219b1ff9aff1c0b0
Original-Change-Id: I973573efd0effc9e0173d2b259ce577b6de38de4
Original-Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/258060
Original-Reviewed-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: http://review.coreboot.org/9786
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
SET_CONFIGURATION(0) stops operation and is moves the
device to addressed mode.
BRANCH=none
BUG=none
TEST=USB device mode still works
Change-Id: I964d90ba8440b6f428896acc9fe63e1114390da6
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 402bc907222d07765b3438967edf26cc1a79d775
Original-Change-Id: Iebad024e1ed2e344dba73b73a9b385a4ac4cb450
Original-Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/250791
Original-Reviewed-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: http://review.coreboot.org/9785
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Some IN transfers must be terminated by an empty packet
because otherwise the host wouldn't know.
The zlp() function determines this requirement in
accordance to USB rules: If the transfer's size is aligned
to the maximum packet size, and the host expects a larger
transfer, add the empty packet as a hint.
BRANCH=none
BUG=none
TEST=USB device mode still works
Change-Id: Ia69f3d017f72a3a0e0b21bac72fe97be184c7daa
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: fd0e946e4948a74a9ed15a5eed6ce827b7672a56
Original-Change-Id: I8153cc5bd2ff1c88e383c1dbcddaf1bf72f9194c
Original-Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/250790
Original-Reviewed-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: http://review.coreboot.org/9784
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Add a framework for USB device mode controllers
and a driver for the ChipIdea controller which
is part of the tegra platform.
TODO:
- fix USB detach/attach
- implement zero length packet handling properly
BUG=chrome-os-partner:35861
TEST=none
BRANCH=none
Change-Id: I8defeea78b5a3bdbf9c1b1222c2702eaf3256b81
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 542332291880c4026a05a960ceb91d37891ee018
Original-Change-Id: Ib4068d201dd63ebeda80157bd3130f3059919cdd
Original-Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/243272
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/8756
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
This check verifies that all mainboard vendors
and boards have a Kconfig.name entry.
Change-Id: I3ed3bfa0d3f78e55a8d54918f5f3f29f51068e48
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-on: http://review.coreboot.org/9707
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
This change switches all mainboard vendors and mainboards
to be autoincluded by Kconfig, rather than having to be mentioned
explicitly.
This means, vendor and mainboard directories are becoming more
"drop in", e.g. be placed in the coreboot directory hierarchy
without having to modify any higher level coreboot files.
The long term plan is to enable out of tree mainboards / components
to be built with a given coreboot version (given that the API did
not change)
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Change-Id: Ib68ce1478a2e12562aeac6297128a21eb174d58a
Reviewed-on: http://review.coreboot.org/9295
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
this is not only for speed but also preventing the cpu from crashing.
the cpu is not happy when cache is cleaned without mmu turned on.
BUG=chrome-os-partner:36691
BRANCH=broadcom-firmware
TEST=boot purin to romstage.
Change-Id: I2445dcc2729798c4fc56fa191cbc8471ef708d08
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 9e35c925b75213e1d35bf191f22c39aaf1726eeb
Original-Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org>
Original-Change-Id: Icaf8c506df258edb99413949e6e3089a2b1a91af
Original-Reviewed-on: https://chrome-internal-review.googlesource.com/199388
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Original-Commit-Queue: Daisuke Nojiri <dnojiri@google.com>
Original-Tested-by: Daisuke Nojiri <dnojiri@google.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/251306
Reviewed-on: http://review.coreboot.org/9768
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <edward.ocallaghan@koparo.com>
|
|
we also pick no RETURN_FROM_VERSTAGE.
BUG=none
BRANCH=broadcom-firmware
TEST=booted b0 board
Change-Id: Iddd95f233a614187ae6b26f351a289c23f25742f
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 243598925333982b40297adad878c461990d7d70
Original-Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org>
Original-Change-Id: I6ab96628cecb84e061777cc85d6d572823f6d63c
Original-Reviewed-on: https://chromium-review.googlesource.com/251303
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: http://review.coreboot.org/9767
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <edward.ocallaghan@koparo.com>
|
|
this implements udelay.
BUG=chrome-os-partner:36011
BRANCH=broadcom-firmware
TEST=measured 10 sec of delay by stopwatch
Change-Id: I833b71fac98a871bff71478221a55e1ca15c13df
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 137456e63931052f80247b72f98f958afdba8a27
Original-Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org>
Original-Change-Id: Ib5e33a19421eae900800fce94e9fd51bc2c665c4
Original-Reviewed-on: https://chromium-review.googlesource.com/251302
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: http://review.coreboot.org/9766
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <edward.ocallaghan@koparo.com>
|
|
BUG=chrome-os-partner:31438
BRANCH=none
TEST=built and booted on urara with follow-up patches
Change-Id: I0ed55f372e095f6b63a47734c4d223a575f63904
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: a013de7daa7bf9d8a5f59e292c2a01401568d738
Original-Change-Id: I8ddf9e65a8ac3d4b09032a741b725c78251f14c9
Original-Signed-off-by: David Hendricks <dhendrix@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/243212
Original-Reviewed-by: Ionela Voinescu <ionela.voinescu@imgtec.com>
Reviewed-on: http://review.coreboot.org/9778
Tested-by: build bot (Jenkins)
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
This allows us to define the serial console UART on a per-board
basis.
BUG=chrome-os-partner:31438
BRANCH=none
TEST=built and booted on urara w/ follow-up patches
Change-Id: Idbb0d39bf8855df4312f7499c60b8b92826fdd07
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: ed4cfdd5ed6ccbf87a50f56d3e07f2f1a9d49464
Original-Change-Id: I3faeb92f026062cded390603a610e5b8f7c9bc12
Original-Signed-off-by: David Hendricks <dhendrix@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/243211
Original-Reviewed-by: Ionela Voinescu <ionela.voinescu@imgtec.com>
Reviewed-on: http://review.coreboot.org/9777
Tested-by: build bot (Jenkins)
Reviewed-by: David Hendricks <dhendrix@chromium.org>
|
|
This patch fixes a bug that caused non-x86 boards to use the poor man's
assert() version with a lot more instructions per invocation and
hexadecimal line numbers in __PRE_RAM__ environments. This was really
just an oversight in the ARM port... even x86 uses a proper printk() in
most cases (those with CAR) and there's no reason not to do so on the
generally even more flexible SRAM-based architectures.
Additionally, it adds a new Kconfig option to make failed assertions and
BUG() calls halt again. This seems to have been the original intention,
but was commented out once out of fear that this might prevent
production systems from booting. It is still a useful debugging feature
though (since otherwise assertions can easily just scroll past and get
overlooked), so the user should be able to decide the this based on his
needs.
(Also changed error messages for both to include the word "ERROR", since
grepping for that is the most sophisticated way we currently have to
detect firmware problems. Some automated Chromium OS suspend tests check
for that.)
BRANCH=veyron
BUG=None
TEST=Booted Jerry. Compared binary sizes before and after, new version's
bootblock is some ~600 bytes smaller.
Change-Id: I894da18d77e12bf104e443322e2d58e60564e4b7
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 6a5343124719c18a1c969477e3d18bda13c0bf26
Original-Change-Id: I0268cfd67d8c894406b18bb3759a577944bcffb1
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/250661
Original-Reviewed-by: Vadim Bendebury <vbendeb@chromium.org>
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/9775
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <edward.ocallaghan@koparo.com>
|
|
stmicro flash chips use 2 bytes as a device id: upper byte for memory
type and lower byte for capacity. with this change, we will use all 2
bytes to identify a chip.
BUG=none
BRANCH=broadcom-firmware
TEST=booted purin and verified n25q256a was identified.
Change-Id: I8f382eddc4fa70d3deceb4f9d2e82026a7025629
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 12f70a1d4b7e1142afec9ce097c4a21b6225f66e
Original-Change-Id: Id3378a77318fabb74ddb30f1a9549010636872ba
Original-Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org>
Original-Reviewed-on: https://chrome-internal-review.googlesource.com/199387
Original-Reviewed-by: Corneliu Doban <cdoban@broadcom.com>
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Original-Commit-Queue: Daisuke Nojiri <dnojiri@google.com>
Original-Tested-by: Daisuke Nojiri <dnojiri@google.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/251305
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/9774
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Edward O'Callaghan <edward.ocallaghan@koparo.com>
|
|
Compile in support for the STM flash devices.
BRANCH=storm
BUG=chrome-os-partner:33489
TEST=verified that both spansion and stm flash devices boot as
expected.
Change-Id: Ib616b2b52d29b20b4447c92115181a92c524ac39
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 34c0147b45551e9161e3f0e342a753907f27f9ae
Original-Change-Id: I922afb91cc3ac5bf459d9746817d7677986b93cd
Original-Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/248993
Original-Reviewed-by: Trevor Bourget <tbourget@codeaurora.org>
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/9773
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Edward O'Callaghan <edward.ocallaghan@koparo.com>
|
|
That function requirement was added upstream but not in Chromium, so
add an implementation.
Change-Id: Ie384b315adb205586defa730b843c7c8e96f77fb
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Reviewed-on: http://review.coreboot.org/9776
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Bootblock does not allow using malloc, use statically allocated chip
structures instead.
BRANCH=storm
BUG=chrome-os-partner:33489
TEST=both drivers compile when configured in, also booted whirlwind
with an STM compatible SPI NOR flash.
Change-Id: I154c33ce5fc278d594205d8b8e62a56edb4e177e
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: eedbb959a595e0898e7a1dd551fc7c517a02f370
Original-Change-Id: I29b37107ac1d58a293f531f59ee76b3d8c4b3e7c
Original-Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/248992
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/9772
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
This is necessary to make sure that bootblock uses the default CBFS
header (as it ought to) when multiple CBFS images support is enabled.
BRANCH=storm
BUG=chrome-os-partner:34161, chromium:445938
TEST=with the rest of the patches applied storm boots all the way inot
the Linux prompt
Change-Id: I5e029d95c5cb085794c7bf5f44513b2144661e38
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 75b2c2ef6c8287db7c3e5879cacfd5dcba4391ac
Original-Change-Id: I5c352921b4c9b6a3294f4658d174e0842d2ee365
Original-Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/237661
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/9770
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
This is the intialization code specific to the Winbond
W972GG6JB-25 part using Synopsys DDR uMCTL and DDR Phy.
This is DDR2 initialization code only (currently present
on the bring up board). DDR3 initialization code will follow
for boards having DDR3 memory.
The programming procedure that is executed at power up to bring
up the uMCTL, PHY and memories into a state where reads and
writes to the memory can be performed is the following:
1. uPCTL (Universal DDR protocol controller) initialization
The timining registers TOGCNT1U, TINIT, TOGCNT100N and TRSTH
needed for driving the memory power-up sequence are programmed
as a function of the internal timers clock frequency.
Organization (memory chip specific) values are set
(column/bank/row address width and number of ranks), together
with other static values (latency, timing, power up configuration).
All these values are static, provided by the datasheet,
being determined by the memory type, size and frequency.
2. PHY initialization
The PHY is programmed with datasheet provided values,
specifying the initialization values for it to send to the
external memory (timing parameters).
Also, delay lines (DLL) and strength of drive pads are
calibrated (based on external conditions: temperature,
voltage, noise) and locked. After that, the PHY goes
through a trainig process (also dependent on the
current conditions at boot time) to establish precise
timing configuration between the DDR clock and DQS (data strobe)
and between DQS and DQ (data).
3. Memory power up
4. Switch from configuration state to access state.
BUG=chrome-os-partner:31438, chrome-os-partner:37087
TEST=tested on Pistachio bring up board -> DDR initialized
properly and ramstage executed correctly
DDR2 is also tested during chip sort.
Corner cases (performace of DDR in different conditions)
will be tested after the chip reaches a stable state.
BRANCH=none
Change-Id: I0093dc175d064aad03052d5281679b008c1bf012
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 3d0bacea0fd5bd3b12008b47e80de8398f447785
Original-Change-Id: I8437db6c84d77c4c51a3ee2b09cd3d14913c0d16
Original-Signed-off-by: Ionela Voinescu <ionela.voinescu@imgtec.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/241424
Original-Reviewed-by: Vadim Bendebury <vbendeb@chromium.org>
Original-Commit-Queue: Vadim Bendebury <vbendeb@chromium.org>
Original-Tested-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: http://review.coreboot.org/9769
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <edward.ocallaghan@koparo.com>
|
|
BUG=None
BRANCH=None
TEST=Compiles successfully
Change-Id: Ic5c2dafd87641879074f98d023de0379c6e2bfba
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 3ba476b8a436303603d7205d19f66f06c63118cd
Original-Change-Id: I6a1404ff23d62100739919e8f569da2041038f01
Original-Signed-off-by: Furquan Shaikh <furquan@google.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/252352
Original-Tested-by: Furquan Shaikh <furquan@chromium.org>
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Original-Commit-Queue: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: http://review.coreboot.org/9763
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
broadcom cygnus hangs if we clean caches by dcache_clean_invalidate_all
at bootblock entry point. this change makes startup code call
dcache_invalidate_all instead.
other boards theoretically should not be affected as long as maskrom
does not hand off execution to bootblock with dirty cache.
BUG=chrome-os-partner:36648,chrome-os-partner:36691
BRANCH=broadcom-firmware
TEST=boot cygnus b0 board, messages were printed on console:
coreboot-688aae9-dirty bootblock Mon Feb 9 13:21:02 PST 2015
starting...
Exception handlers installed.
Change-Id: I05777ca525c97bb3d7cbb5ea7e872a602dcd5a19
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 59de5328df9d0502a3b3f7c624d3e86e038de50e
Original-Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org>
Original-Change-Id: I9b8850846b941e7e62712e90cc28ad14a68da393
Original-Reviewed-on: https://chromium-review.googlesource.com/251304
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: http://review.coreboot.org/9762
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Storm devices' recovery button is overloaded. Pressing it when the
system is running is supposed to reset the device. To trigger recovery
mode the button must be held pressed for at least 5 seconds after
reset.
Currently interpreting the recovery button state is the responsibility
of the board (vboot gets a consolidated state, which is a combination
of several conditions), so the simplest way to implement this feature
is to make the board follow the recovery button state.
In case the button is not pressed when it is first sampled, its state
is saved immediately and no recovery request is reported. In case the
button is pressed when it is first sampled, the board code keeps
polling it up to 5 seconds and acts accordingly.
BRANCH=storm
BUG=chrome-os-partner:36059
TEST=tried starting a whirlwind with recovery button pressed for
various durations, it entered recovery mode when the button was
pressed longer than 5 seconds.
Change-Id: Icb3250be7c2a76089c070acd68cb521d1399e245
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 45e7265bc760944f93dd98903d39d2b30aa96365
Original-Change-Id: Iab3609ebce3a74e3d0270775b83f3cf03a8837ca
Original-Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/251711
Original-Reviewed-by: Stefan Reinauer <reinauer@chromium.org>
Reviewed-on: http://review.coreboot.org/9761
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
BUG=none
BRANCH=none
TEST=P4 board boots and selects correct dts file
Change-Id: Icdfdef9b82bd53413e45713f9ceef2e0c2be16a8
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 0674037b1f00845ffcd129cb54571f185b42af40
Original-Change-Id: If14e2586c4ef5b44af1754b3f06126b79473798b
Original-Signed-off-by: David Riley <davidriley@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/250634
Original-Reviewed-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: http://review.coreboot.org/9760
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
The GSBI driver is extended to be able to program the CTRL reg for any given
GSBI block. The NS and MD registers programming is made more readable by
programming the M, N, D and other bits of the registers individually.
Defined configure structs for each QUP block to be able to track the init
status for each qup.
Configured GPIO8 and GPIO9 for I2C fuction.
BRANCH=chromeos-2013.04
BUG=chrome-os-partner:36722
TEST=Booted up storm P0.2, verified that the TPM on GSBI1 still works.
Change-Id: I17906beedef5c80267cf114892080b121902210a
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 07bc79211770decc1070c3a88874a4e452b8f5bc
Original-Change-Id: I841d0d419f7339f5e5cb3385da98786eb18252ad
Original-Signed-off-by: Sourabh Banerjee <sbanerje@codeaurora.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/250763
Original-Reviewed-by: Vadim Bendebury <vbendeb@chromium.org>
Original-Trybot-Ready: Vadim Bendebury <vbendeb@chromium.org>
Original-Commit-Queue: Vadim Bendebury <vbendeb@chromium.org>
Original-Tested-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: http://review.coreboot.org/9759
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Add a clock control driver to initialize the clock tree inside the
low-power audio subsystem. Depthcharge builds up on this to enable
audio function on storm.
The clock is hardcoded for 48KHz frame rate, two 16 bit channels.
BRANCH=storm
BUG=chrome-os-partner:35247
TEST=with depthcharge patches applied and Using depthcharge CLI audio
test program verified that the target generates sensible sounds
audio 100 100
audio 1000 5000
Change-Id: I56513fc782657ade99b6e43b2d5d3141d27ecc4e
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 0d4f408408aa38b2f0ee19b83ed490de39074760
Original-Change-Id: If8ffc326698fcea17e05d536930d927ca553481f
Original-Signed-off-by: Kenneth Westfield <kwestfie@codeaurora.org>
Original-Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/248830
Original-Reviewed-by: Dylan Reid <dgreid@chromium.org>
Reviewed-on: http://review.coreboot.org/9758
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
This patch adds the necessary platform glue to allow the use of
software-driven I2C bit banging on the RK3288. This is just a debugging
feature that can be used to reproduce certain I2C failure cases.
Also fix Makefile verstage linking for the feature and add some new
rk3288 IOMUX macros as needed.
BRANCH=None
BUG=None
TEST=Added "CONFIG_SOFTWARE_I2C=y" to configs/config.veyron_jerry,
wrapped Jerry's bootblock and verstage in software_i2c_attach/detach()
calls, confirmed that both PMIC and TPM could be driven correctly with
software I2C driver. Tried out different combinations of
software_i2c_wedge_ack() and software_i2c_wedge_read() on the PMIC and
observed transfer results with the hardware controller after reboot...
the worst that would happen is that the first register read-modify-write
(DCDC_ILMAX) would fail to read, but all later transfers would be fine.
Since that register is written twice (due to current BUCK1 ramp
implementation) and is not terribily important anyway, I think we don't
need to worry about wedging problems.
Change-Id: Iba801ee61d30fb1fd3aef8300612c67fa50c441b
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 24dfca9bab38a20c40ef0c2dd4c775b8d8f47487
Original-Change-Id: I96777300a57c85471bad20e23a455551e9970222
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/247890
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/9757
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
move mmu setup from RAM stage to boot block
Enabling mmu earlier, helps speed up the boot time.
BRANCH=storm
BUG=chrome-os-partner:35024
TEST=Verified the mmu table dump matches the programmed values.
Change-Id: I8f581538d5dfd0d78538c9fe50f689d54b740685
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: fb799a6d61f9c2f478434a71584d0edb94af4b59
Original-Change-Id: I110497875002a88add7eb4312a70c0de8c28bc4f
Original-Signed-off-by: Deepa Dinamani <deepad@codeaurora.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/247120
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Original-Commit-Queue: Trevor Bourget <tbourget@codeaurora.org>
Reviewed-on: http://review.coreboot.org/9756
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
This brings brain, danger, and rialto up to parity with other
veyron platforms as far as eventlog functionality is concerned.
BUG=chrome-os-partner:34436
BRANCH=none
TEST="mosys eventlog list" shows events (tested on Brain)
Change-Id: I186c5d18e5351c0eaf08ffecfd87506283c44b19
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 1764bc53147718031231a6d125a4a1a96c4c6a8f
Original-Signed-off-by: David Hendricks <dhendrix@chromium.org>
Original-Change-Id: Ief09299965f6f21bc5a40cef31cde61344025c2a
Original-Reviewed-on: https://chromium-review.googlesource.com/239979
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: http://review.coreboot.org/9755
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
This applies a previous patch ("chromeos: Provide common watchdog
reboot support") to some veyron platforms that were missing it.
BUG=none
BRANCH=none
TEST=built and booted on Brain
Change-Id: I3eb431a57367b8f885844e4353a78f77515f5195
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: b0c87dd4217917a35817c719efe43dd4ec442df0
Original-Signed-off-by: David Hendricks <dhendrix@chromium.org>
Original-Change-Id: I2861939655a995d309847f64cecd974a740fae37
Original-Reviewed-on: https://chromium-review.googlesource.com/245633
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: http://review.coreboot.org/9754
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
BUG=none
BRANCH=tot
TEST=emerge-purin libpayload depthcharge coreboot chromeos-bootimage
Change-Id: I6a46067a288ecea352a2724c62c62066e3f4a383
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 355371317dde0546fbab2cd109bc17463f77c4fd
Original-Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org>
Original-Change-Id: I8c43acc4d270c3b2d7c18af07c077a553e3c6f6f
Original-Reviewed-on: https://chromium-review.googlesource.com/245492
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/9753
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
we will use dvs to adjust the voltage in kernel, if device reset
by watchdog in kernel, the dvs gpio may not reset, and we use the
i2c to adjust rk808 voltage in coreboot, so it may failure. so we
move the reboot_from_watchdog() before the rk808 setting.
BUG=None
TEST=Boot from speedy
BRANCH=None
Change-Id: I809c63153d49680d9c84462aafd7bae09106fa6e
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 76efb4b0196eecc84664a4c5dce2221152a39c0a
Original-Change-Id: I92b5c6413bbffe30566178de89df1f9683790982
Original-Signed-off-by: huang lin <hl@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/244289
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Original-Commit-Queue: Julius Werner <jwerner@chromium.org>
Original-Tested-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: http://review.coreboot.org/9752
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
this change covers bootblock and romstage.
BUG=none
BRANCH=tot
TEST=ran emerge-purin coreboot
Change-Id: Ifffb2e93189e8e85338de469432f3296e3e71791
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: cd479583404958f72461e9c1639f0288a00f228e
Original-Change-Id: Iaee4a8c457e42386a4100a8121144b8cf5f21e8c
Original-Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/242853
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/9751
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
This commit covers bootblock and romstage.
BUG=none
BRANCH=tot
TEST=ran emerge-purin coreboot
Change-Id: I88e2dffb9e46ba5b066190e844a6a7302adcfdc7
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: b3af6343a74263f086fe82c600559e8204e7dec0
Original-Change-Id: I447ed5f6ed181cfc9d5521b8c57e5fe0036a3f71
Original-Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/242854
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/9750
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Many ChromeOS devices use a GPIO to reset the system, in order to
guarantee that the TPM cannot be reset without also resetting the CPU.
Often chipset/SoC hardware watchdogs trigger some kind of built-in
CPU reset, bypassing this GPIO and thus leaving the TPM locked. These
ChromeOS devices need to detect that condition in their bootblock and
trigger a second (proper) reboot.
This patch adds some code to generalize this previously
mainboard-specific functionality and uses it on Veyron boards. It also
provides some code to add the proper eventlog entry for a watchdog
reset. Since the second reboot has to happen before firmware
verification and the eventlog is usually only initialized afterwards, we
provide the functionality to place a tombstone in a memlayout-defined
location (which could be SRAM or some MMIO register that is preserved
across reboots).
[pg: Integrates
'mips: Temporarily work around build error caused by <arch/io.h> mismatch]
BRANCH=veyron
BUG=chrome-os-partner:35705
TEST=Run 'mem w 0xff800000 0x9' on a Jerry, watch how a "Hardware
watchdog reset" event appears in the eventlog after the reboot.
Change-Id: I0a33820b236c9328b2f9b20905b69cb934326f2a
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: fffc484bb89f5129d62739dcb44d08d7f5b30b33
Original-Change-Id: I7ee1d02676e9159794d29e033d71c09fdf4620fd
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/242404
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Original-Commit-Id: c919c72ddc9d2e1e18858c0bf49c0ce79f2bc506
Original-Change-Id: I509c842d3393bd810e89ebdf0dc745275c120c1d
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/242504
Original-Reviewed-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/9749
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
BUG=chrome-os-partner:34436
BRANCH=none
TEST=Built and booted on pinky w/ depthcharge fmap patch,
used mosys to verify that eventlog entries get populated:
entry="0" timestamp="2015-01-06 13:45:33" type="Log area cleared" bytes="4096"
entry="1" timestamp="2015-01-06 13:45:33" type="System boot" count="0"
entry="2" timestamp="2015-01-06 13:45:33" type="Chrome OS Developer Mode"
Change-Id: I74ba8b271328453c8b91f11e7858754a80806c31
Signed-off-by: Stefan Reinauer <reinauer@chromium.org>
Original-Commit-Id: 197010f057f4835a30ed2e71f47ca51fc181afe4
Original-Signed-off-by: David Hendricks <dhendrix@chromium.org>
Original-Change-Id: I19cb884be5c3e00975599e96e0223e33d32e7c0d
Original-Reviewed-on: https://chromium-review.googlesource.com/238830
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Original-Commit-Queue: Julius Werner <jwerner@chromium.org>
Original-Tested-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: http://review.coreboot.org/9644
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Turns out there are uses for memlayout regions not specific to vboot2.
Rather than add yet another set of headers for a single region, let's
make the vboot2 one common for chromeos.
BRANCH=veyron
BUG=chrome-os-partner:35705
TEST=Booted Jerry, compiled Blaze, Cosmos, Ryu and Storm.
Change-Id: I228e0ffce1ccc792e7f5f5be6facaaca2650d818
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: c6d7aab9f4e6d0cfa12aa0478288e54ec3096d9b
Original-Change-Id: I1dd7d9c4b6ab24de695d42a38913b6d9b952d49b
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/242630
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/9748
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Dependency tracking in incremental builds is currently broken for the
ramstage, due to the intermediate linking step into one ramstage.o file
per directory. The original xxx.ramstage.o files are removed from
ramstage-objs, so they don't end up in allobjs and won't get translated
into DEPENDENCIES. This patch explicitly adds them to DEPENDENCIES
beforehand to resolve the issue.
BRANCH=None
BUG=None
TEST=Built, ran 'touch src/include/cbmem.h' and built again
incrementally. Confirmed that objects dependent on the modified header
such as timestamp.ramstage.o get rebuilt correctly.
Change-Id: I3ba411e4073b38e038445aadceeccfe6c09670c8
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 9c57d6a8421a109ee3e87567c9add579f9ae761e
Original-Change-Id: Ife529ad8f5c011456c1e0c380356f1b1bb5047cb
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/233571
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/9745
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
The 4 byte offset value will be stored in SRAM and shared between
different coreboot stages.
BRANCH=storm
BUG=chrome-os-partner:3416, chromium:445938
TEST=with the rest of the patches in, storm successfully boots into
Linux login prompt
Change-Id: Id8df75b0c679e274532660d55410291e59f3b520
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 8f2f7cf6263f4c2db70b1c87ec67f6b0308059b3
Original-Change-Id: I1ebfada93e222992300cd695d04669988206d4b1
Original-Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/237660
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/9744
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Edward O'Callaghan <edward.ocallaghan@koparo.com>
|
|
This patch introduces a new option (CONFIG_MULTIPLE_CBFS_INSTANCES) to
allow multiple CBFS instances in the bootrom.
When the new option is enabled, the code running on the target
controls which CBFS instance is used. Since all other then header CBFS
structures use relative addressing, the only value which needs
explicit setting is the offset of the CBFS header in the bootrom.
This patch adds a facility to set the CBFS header offset. The offset
value of zero means default. i.e. the CBFS initialization code still
discovers the offset through the value saved at the top of the ROM.
BRANCH=storm
BUG=chrome-os-partner:34161, chromium:445938
TEST=with the rest patches in, storm target successfully boots from RW
section A.
Change-Id: Id8333c9373e61597f0c653c727dcee4ef6a58cd2
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: e57a3a15bba7cdcca4a5d684ed78f8ac6dbbc95e
Original-Change-Id: I4c026389ec4fbaa19bd11b2160202282d2f9283c
Original-Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/237569
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/9747
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Edward O'Callaghan <edward.ocallaghan@koparo.com>
|
|
Pistachio UART closely matches 8250, the only difference is that its
register file is mapped to a 32 bit bus.
Provide a function to report register with so that the Coreboot table
entry gets correct value.
BRANCH=none
BUG=chrome-os-partner:31438
TEST=with the rest of the patches integrated depthcharge console messages
show up when running on the FPGA board
Change-Id: Icd72b115b4f339800d6c8b210a6617398232f806
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: e1dc4156949b20efafbca2c19ff424436a400087
Original-Change-Id: Icafb014af338e05bbf1044b791683733685ffab3
Original-Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/240028
Original-Reviewed-by: Ionela Voinescu <ionela.voinescu@imgtec.com>
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/9740
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Some SOCs (like pistachio, for instance) provide an 8250 compatible
UART, which has the same register layout, but mapped to a bus of a
different width.
Instead of adding a new driver for these controllers, it is better to
have coreboot report UART register width to libpayload, and have it
adjust the offsets accordingly when accessing the UART.
BRANCH=none
BUG=chrome-os-partner:31438
TEST=with the rest of the patches integrated depthcharge console messages
show up when running on the FPGA board
Change-Id: I05891a9471a5369d3bfafe90cd0c9b0a7e5a667e
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 2c30845f269ec6ae1d53ddc5cda0b4320008fa42
Original-Change-Id: Ia0a37cd5f24a1ee4d0334f8a7e3da5df0069cec4
Original-Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/240027
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/9739
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Some SOCs (like pistachio, for instance) provide an 8250 compatible
UART, which has the same register layout, but mapped to a bus of a
different width.
Instead of adding a new driver for these controllers, it is better to
have coreboot report UART register width to libpayload, and have it
adjust the offsets accordingly when accessing the UART.
BRANCH=none
BUG=chrome-os-partner:31438
TEST=with the rest of the patches integrated depthcharge console messages
show up when running on the FPGA board
Change-Id: I30b742146069450941164afb04641b967a214d6d
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 2c30845f269ec6ae1d53ddc5cda0b4320008fa42
Original-Change-Id: Ia0a37cd5f24a1ee4d0334f8a7e3da5df0069cec4
Original-Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/240027
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/9738
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
There was a recent patch by Deepa Dinamani applied to coreboot's
cache.c which fixed a bug that occurred when icache is on but dcache
is off ("arch: armv7: Fix cache sync instructions."). Although this
bug is not likely to be encountered by the time libpayload is run,
it's worth applying it to keep things in sync.
BUG=none
BRANCH=none
TEST=n/a since we have icache and dcache enabled on all ARM platforms
when libpayload is run.
Change-Id: I83d9f96acb702975585e5d47c90e2ddaca488f6d
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 31f985b58ac9227684fbe27481129ba01fd3ab8a
Original-Signed-off-by: David Hendricks <dhendrix@chromium.org>
Original-Change-Id: I4ab0d97ef3a97dcd0fa96e10273c3b32486e0b40
Original-Reviewed-on: https://chromium-review.googlesource.com/243276
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: http://review.coreboot.org/9737
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
- Hynix H5TC4G63CFR-PBA, ramcode = 5
BUG=chrome-os-partner:34695
TEST=emerged coreboot, booted successfully into kernel.
Change-Id: I53f9ebd9c38c645d1eb8b685d39e8beb55bd3c6a
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: ee6fdcc28402fe324d08b713498488d863d1d30f
Original-Change-Id: I829d4e1f992eadd445c313729eb4bca5ce602f53
Original-Reviewed-on: https://chromium-review.googlesource.com/245947
Original-Reviewed-by: Neil Chen <neilc%nvidia.com@gtempaccount.com>
Original-Tested-by: Neil Chen <neilc%nvidia.com@gtempaccount.com>
Original-Reviewed-by: Tom Warren <twarren@nvidia.com>
Original-Reviewed-by: David Hendricks <dhendrix@chromium.org>
Original-Commit-Queue: Neil Chen <neilc%nvidia.com@gtempaccount.com>
Reviewed-on: http://review.coreboot.org/9736
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
BUG=none
BRANCH=ToT
TEST=Built daisy.
Change-Id: I64033f8e7beb247b2b8bd66e58de6c5e263ee634
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 1ff51e887a07a0f2426e5111df683ce2a9d4097d
Original-Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org>
Original-Change-Id: Id6e006be1db08933dc97b5e797a85f3cbf9f6486
Original-Reviewed-on: https://chromium-review.googlesource.com/232513
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: http://review.coreboot.org/9735
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
we use Kconfig define sdram size before, but there may use
different sdram size in the same overlay, so we must detect
sdram size at runtime now. If we use 4G byte sdram, we can
use[0x00000000:0xff000000], since the [0xff000000:0xffffffff]
is the register space.
BUG=chrome-os-partner:35521
TEST=Boot from mighty
BRANCH=None
Change-Id: I7a167c268483743c3eaed8b71c7ec545a688270c
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: ad4f27dd08c467888eee87e3d9c4ab3077751898
Original-Change-Id: Ib32aed50c9cae6db495ff3bab28266de91f3e73b
Original-Signed-off-by: huang lin <hl@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/243139
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: http://review.coreboot.org/9734
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
I always had that TODO comment in there but I had already forgotten what
I even meant by it. It's really just a simple cleanup... this function
is (currently) veyron-specific and doesn't belong in common code.
BRANCH=veyron
BUG=None
TEST=Booted Jerry.
Change-Id: Iccd6130c90e67b8ee905e188857c99deda966f14
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: d188398704575ad2fedc2a715e609521da2332b0
Original-Change-Id: I6ce701a15a6542a615d3d81f70aa71662567d4fa
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/241190
Reviewed-on: http://review.coreboot.org/9733
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
We've traditionally tucked the framebuffer at the end of memory (above
CBMEM) on ARM and declared it reserved through coreboot's resource
allocator. This causes depthcharge to mark this area as reserved in the
kernel's device tree, which may be necessary to avoid display corruption
on handoff but also wastes space that the OS could use instead.
Since rk3288 boards now have proper display shutdown code in
depthcharge, keeping the framebuffer memory reserved across the handoff
(and thus throughout the lifetime of the system) should no longer be
necessary. For now let's just switch the rk3288 implementation to define
it through memlayout instead, which is not communicated through the
coreboot tables and will get treated as normal memory by depthcharge.
Note that this causes it to get wiped in developer/recovery mode, which
should not be a problem because that is done in response to VbInit()
(long before any images are drawn) and 0 is the default value for a
corebootfb anyway (a black pixel).
Eventually, we might want to think about adding more memory types to
coreboot's resource system (e.g. "reserved until kernel handoff", or
something specifically for the frame buffer) to model this situation
better, and maybe merge it with memlayout somehow.
CQ-DEPEND=CL:239470
BRANCH=veyron
BUG=chrome-os-partner:34713
TEST=Booted Jerry, noticed that 'free' now displays 0x7f000 more bytes
than before (curiously not 0x80000 bytes, I guess there's some alignment
waste in the kernel somewhere). Made sure the memory map output from
coreboot looks as expected, there's no visible display corruption in
developer/recovery mode and the 'cbmem' utility still works.
Change-Id: I12b7bfc1b7525f5a08cb7c64f0ff1b174df252d4
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 10afdba54dd5d680acec9cb3fe5b9234e33ca5a2
Original-Change-Id: I1950407d3b734e2845ef31bcef7bc59b96c2ea03
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/240819
Original-Reviewed-by: David Hendricks <dhendrix@chromium.org>
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/9732
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Each type of cache might have different cache line size.
Call the proper get_<*>cache_line function for each cache
type.
Fixes problem with get_L2cache_line which previously
targeted L3 cache line in the config register, instead of
L2 cache.
TODO: add support for tertiary caches and have cache
operations be called per CPU, not per architecture.
BUG=chrome-os-partner:31438
TEST=tested on Pistachio bring up board; worked as expected;
BRANCH=none
Change-Id: I7de946cbd6bac716e99fe07cb0deb5aa76c84171
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 62e2803c6f2a3ad02dc88f50a4ae2ea00487e3f4
Original-Change-Id: I03071f24aacac1805cfd89e4f44b14ed1c1e984e
Original-Signed-off-by: Ionela Voinescu <ionela.voinescu@imgtec.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/241853
Original-Reviewed-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/9731
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Add a function that allows reading of the status register
from the SPI chip. This can be used to determine whether
write protection is enabled on the chip.
BUG=chrome-os-partner:35209
BRANCH=haswell
TEST=build and boot on peppy
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/240702
Reviewed-by: Shawn N <shawnn@chromium.org>
(cherry picked from commit c58f17689162b291a7cdb57649a237de21b73545)
Change-Id: Ib7fead2cc4ea4339ece322dd18403362c9c79c7d
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 9fbdf0d72892eef4a742a418a347ecf650c01ea5
Original-Change-Id: I2541b22c51e43f7b7542ee0f48618cf411976a98
Original-Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/241128
Original-Reviewed-by: Shawn N <shawnn@chromium.org>
Reviewed-on: http://review.coreboot.org/9730
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
We've decided that it is generally okay for coreboot to expect unaligned
accesses to work. Trying to find all instances of unaligned access
opportunities and working around them in software would be an
unsustainable whack-a-mole contest. Instead, architectures and boards
need to make sure they conform to this, which on ARM and ARM64 requires
setting up paging early in the bootblock.
Other architectures (x86, ARM64, MIPS) already generate code in this
manner. ARM still had an -mno-unaligned-access flag hanging around that
has been copied so many times its initial origin was lost in time
(probably U-Boot). Let's remove it for consistency between architectures
and to improve code generation.
BRANCH=veyron
BUG=None
TEST=Booted Jerry and Blaze. Looked at the disassembly for
timestamp_sync() and confirmed that it only gives you half as much eye
cancer as before (GCC still somehow insists on byte accesses when
zeroing fields which is very odd, but at least that terrible AND/OR mess
is gone). Measured a boot time increase of about 11ms on Jerry (mostly
faster timestamp and CBFS accesses). Could not test Storm because
despite our claimed abundance of test devices, every time I get one of
them it magically disappears again in less than a week.
Change-Id: I8fc08cc7ce4471651a51ee795269909ef69277c8
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 07591fadb89bd127fe065abf0b9ba3facecf1aeb
Original-Change-Id: I1d046e05bb11822b86e467eafb6aa92e8fbce774
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/241732
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/9728
Tested-by: build bot (Jenkins)
Reviewed-by: Edward O'Callaghan <edward.ocallaghan@koparo.com>
|
|
A payload may want to run erase operations on SPI NOR flash without
re-probing the device to get its properties. This patch passes up
three properties of flash to achieve that:
- The size of the flash device
- The sector size, i.e., the granularity of erase
- The command used for erase
The patch sends the parameters through coreboot and then libpayload.
The patch also includes a minor refactoring of the flash erase code.
Parameters are sent up for just one flash device. If multiple SPI
flash devices are probed, the second one will "win" and its
parameters will be sent up to the payload.
TEST=Observed parameters to be passed up to depthcharge through
libpayload and be used to correctly initialize flash and do an erase.
TEST=Winbond and Gigadevices spi flash drivers compile with the changes;
others don't, for seemingly unrelated reasons.
BRANCH=none
BUG=chromium:446377
Change-Id: I92b7ff0ce66af8d096ec09a4c900829ef6c867e0
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 988c8c68bbfcdfa69d497ea5f806567bc80f8126
Original-Change-Id: Ie2b3a7f5b6e016d212f4f9bac3fabd80daf2ce72
Original-Signed-off-by: Dan Ehrenberg <dehrenberg@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/239570
Original-Reviewed-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: http://review.coreboot.org/9727
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
A payload may want to run erase operations on SPI NOR flash without
re-probing the device to get its properties. This patch passes up
three properties of flash to achieve that:
- The size of the flash device
- The sector size, i.e., the granularity of erase
- The command used for erase
The patch sends the parameters through coreboot and then libpayload.
The patch also includes a minor refactoring of the flash erase code.
Parameters are sent up for just one flash device. If multiple SPI
flash devices are probed, the second one will "win" and its
parameters will be sent up to the payload.
TEST=Observed parameters to be passed up to depthcharge through
libpayload and be used to correctly initialize flash and do an erase.
TEST=Winbond and Gigadevices spi flash drivers compile with the changes;
others don't, for seemingly unrelated reasons.
BRANCH=none
BUG=chromium:446377
Change-Id: Ib8be86494b5a3d1cfe1d23d3492e3b5cba5f99c6
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 988c8c68bbfcdfa69d497ea5f806567bc80f8126
Original-Change-Id: Ie2b3a7f5b6e016d212f4f9bac3fabd80daf2ce72
Original-Signed-off-by: Dan Ehrenberg <dehrenberg@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/239570
Original-Reviewed-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: http://review.coreboot.org/9726
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
This adds a 10us delay in between (re-)configuring and reading
GPIOs in gpio_base2_value() to give the values stored some time
to update.
As far as I know this hasn't bitten us since the function was
added, but adding a short delay here seems like the right thing
to do.
BUG=none
BRANCH=none
TEST=built and booted on Brain
Change-Id: I869cf375680435ad87729f93d29a623bdf09dfbc
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 2484900fc9ceba87220a293de8ef20c3b9b20cfd
Original-Signed-off-by: David Hendricks <dhendrix@chromium.org>
Original-Change-Id: I79616a09d8d2ce4e416ffc94e35798dd25a6250d
Original-Reviewed-on: https://chromium-review.googlesource.com/240854
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: http://review.coreboot.org/9725
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
BUG=chrome-os-partner:31438
TEST=tested on Pistachio FPGA; works as expected.
BRANCH=none
Change-Id: If4493fcb37cf649fb0a56d594ac58556da3aa571
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 0f6764396be1ab17875d9c73624cce48dc6790e6
Original-Change-Id: I925ebd6ea4fc30c1c1d91559f96eaad62d06aba8
Original-Signed-off-by: Ionela Voinescu <ionela.voinescu@imgtec.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/239490
Original-Reviewed-by: Vadim Bendebury <vbendeb@chromium.org>
Original-Commit-Queue: Vadim Bendebury <vbendeb@chromium.org>
Original-Tested-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: http://review.coreboot.org/9724
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
The AS3277 RTC code seems to closely follow the corresponding Linux
driver. Unfortunately, while coreboot (and even other parts of Linux,
like mktime()) directly follows the standard IBM PC RTC time
representation (except for the BCD part), Linux' struct rtc_time decided
to use 0-based (instead of 1-based) months instead.
This patch removes the faulty month offset that was copied into our
driver so that we will generate correct timestamps again.
BRANCH=nyan
BUG=chrome-os-partner:34108
TEST=firmware_EventLog (pre-release version) gets further than before
(and then craps up on unrelated problems with suspend/resume events).
Change-Id: Ica221a8bcfd7c1c6cd7ba382d760b586d511e3a3
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 5b55c3f5bbecc776a71338256b910aecccac1e04
Original-Change-Id: I163fa4778ec534cd9e6f92a6b6dc55e9871a6a82
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/238122
Original-Reviewed-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/9723
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
this change defines a custom romstage entry for bg4cd. the entry code
stalls subcores, sets up the stack, and clears the bss before jumping to main.
BUG=none
BRANCH=tot
TEST=built all current boards. booted cosmos p1
Change-Id: Idde43f94555bec7804a16928c58ce673956a39e5
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 7a35e12eb29b351cc0baaea24344f00d2ba905f6
Original-Change-Id: I9172e873a43847f3ea82cd1d9fd0841f0db83994
Original-Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/238022
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: http://review.coreboot.org/9722
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
this change defines stage_entry as a weak symbol so that a board
can implement custom stage entry code.
BUG=none
BRANCH=tot
TEST=built all current boards. booted cosmos p1.
Change-Id: If8f6945ecdc5047558bb6359aa997867e36f33b9
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 86d5008981d0b01652907baab47a476d784a2ceb
Original-Change-Id: Ib43158c4013e6393d86a9aef37cf444a48b9fc79
Original-Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/238021
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: http://review.coreboot.org/9721
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
The current display init code causes Brain to crash when trying
to allocate resources. This just avoids doing display init if a
config variable is set. Once code has been implemented to properly
setup different types of displays we can get rid of this hack.
BUG=none
BRANCH=none
TEST=built and booted (to depthcharge) on Brain, compiled for
pinky with FEATURES=noclean and ensured config variable is 0
Change-Id: I9a7266c6bff5b7a6eb05b2b21fb65797bee392d6
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 804632ca67eaaf4174ca597d83b8923cb9abd1b7
Original-Signed-off-by: David Hendricks <dhendrix@chromium.org>
Original-Change-Id: I04c9e8181c58fa0608fd20776fa8c4798a023474
Original-Reviewed-on: https://chromium-review.googlesource.com/235922
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: http://review.coreboot.org/9720
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
This patch activates the chip driver for Winbond SPI flash (which,
incidentally, looks 99.9% the same as the Gigadevice driver but still
requires some extra 500+ bytes of object code... there's definitely room
for improvement here). Shuffle around rk3288 memlayout to make a little
more room in the bootblock.
BRANCH=veyron
BUG=chrome-os-partner:34176
TEST=Booted Pinky. Checked bootblock and verstage memsz of final binary
and noticed that both only have less than 500 bytes left against their
memlayout boundary. The next piece of code we add will cause some
serious headaches...
Change-Id: I97ea6ac334104e4219e310afc557c164b2ff19d9
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 8769e5a34ad3cd417132646fbb58ff51c29fb640
Original-Change-Id: Id2f1204c30aa28251cf85cb80d7ca44947388dba
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/236977
Original-Reviewed-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/9719
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
we use the delay 200ms to meet the edp power timing request before,
it waste time, so we use the HPD function to detect the edp panel now.
In previous version, the hardware may not support the edp HPD function,
so in the code it will spend 200ms to detect hpd single, if it don't get
the hpd single, it will contiue the edp initialization process, to compatible
all of the hardware version.
BUG=chrome-os-partner:35623
TEST=Boot from Mighty, and display normal
BRANCH=None
Change-Id: I82c6a80e37fa42eef3521e6ebbf190d7e80fcece
Signed-off-by: Stefan Reinauer <reinauer@chromium.org>
Original-Commit-Id: 7a5343eb9af12cae9a15284217762a91ae24bac6
Original-Change-Id: I21c0ef6ce4643e90a192d8b86659264895b5fda9
Original-Signed-off-by: huang lin <hl@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/242792
Original-Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-on: http://review.coreboot.org/9659
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
backlight timing: LED_VCC->LED_PWM->LED_EN, we modify the
code to meet the timing.
BUG=chrome-os-partner:36201
TEST=Boot from jerry, and scope the backlight timing
BRANCH=None
Change-Id: I6bfa6af176400086e4af0112a63127c1152ca70e
Signed-off-by: Stefan Reinauer <reinauer@chromium.org>
Original-Commit-Id: 52ac0b2944cea7dc860bfea12fe44851436bb7f7
Original-Change-Id: I6c53a822410ad706383c6d9fa2b5f0437775f710
Original-Signed-off-by: huang lin <hl@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/244639
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: http://review.coreboot.org/9658
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
The recovery button on Rialto should be GPIO 255, the LED Push Key.
Note we want to keep the recovery button on servo functional because
many protos are not assembled and developers can't "push" the push key.
The GPIO passed to payloads (and kernel) is only mapped to Push Key.
BUG=none
TEST=emerge-veyron_rialto coreboot chromeos-bootimage
BRANCH=veyron_rialto
Change-Id: I66f94cf232caa53a3b28db517620e4b6e9b9af0e
Signed-off-by: Stefan Reinauer <reinauer@chromium.org>
Original-Commit-Id: 66ee55f6312efaeb337eb2881cd5eff5365b4105
Original-Change-Id: I0a7ebeed6506fbd938084c9a078a7cf1c7b914b9
Original-Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/244515
Original-Reviewed-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/9657
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
