| Age | Commit message (Collapse) | Author |
|---|
|
Coverity is detecting 'sp' as a variable which has not been initialized.
This is obviously not correct, so this patch *TRIES* to mark it as false
I'm not positive that this will work because the annotation needs to go
on the line above the error, but this error is inside of a # define.
Does the whole #define count as one line? Can it go on the line
above the #define in the .h file? Does it have to precede every line
where the #define is used? The documentation doesn't make this clear.
Should suppress coverity issues: 1368525 & 1368527
uninit_use: Using uninitialized value sp.
Change-Id: Ibae5e206c4ff47991ea8a11b6b59972b24b71796
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/18247
Tested-by: build bot (Jenkins)
Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
|
|
Previously, the file -i command identified vga_font_8x16.c as
application/octet-stream; charset=binary
Now it identifies as:
text/x-c; charset=us-ascii
- Remove non-ascii characters
Change-Id: I6b513e6457a31828a6e94c954a7e2e7ee18fd4d6
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/18372
Tested-by: build bot (Jenkins)
Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
|
|
Apply the measured rise and fall times for I2C bus 1 on Eve
so it can be tuned properly for 400KHz operation.
BUG=chrome-os-partner:63020
TEST=verify I2C1 bus speed with a scope
Change-Id: I32b5aa460ea35aadca7f3d52324a64880764919f
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/18396
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Currently UART0 GPIOs are being put into native mode during FSP-S
stage, so have ramstage re-configure them back to regular GPIO mode.
GPP_C8 does not seem to be functioning properly when routed to the
APIC, possibly due to the UART0 being enabled even though it is unused,
which is required because UART0 is PCI 1e.0 and so must be present for
other 1e.x functions to be enumerated. Instead, use this pin as a GPIO
interrupt so it will be routed through the GPIO controller at IRQ 14.
GPP_C9 was inverted and was only working because the pin was being
re-configured in FSP-S.
Also export the reset gpio as a device property so it can be used by
the kernel driver, which will stop it from complaining at boot.
BUG=chrome-os-partner:61233
TEST=verify that the interrupt and device is functional in the OS
Change-Id: Iaf9efbf50a13a981c6a9bbd507475777837e9c12
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/18395
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
There is an enable_s0ix config option in the devicetree that should
be used to disable it when not set:
- do not export C8/C9/C10 C-states in _CST
- do not enable SLP_S0 in FSP
BUG=chrome-os-partner:58666
TEST=test on eve board to ensure that OS only sees 3 ACPI C-states
instead of 6 and that it no longer attempts to enter C10
Change-Id: I90e4dc776d1d17d0b700cda63c8476786cd2e4ff
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/18394
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Add support for more ACPI features in the generic SPI ACPI
driver so it can be flexible enough to support more devices,
or devices in different configurations.
- add a wake pin
- add support for using IRQ GPIO instead of PIRQ
- add power resource support with enable and reset gpios
BUG=chrome-os-partner:61233
TEST=ensure existing SSDT generation is unchanged,
and test that new features generate expected code
Change-Id: Ibe37cc87e488004baa2c08a369f73c86e6cd6dce
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/18393
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Add individual macros for the various interrupt types so
they can be used in devicetree.
BUG=chrome-os-partner:58666
TEST=nothing uses this yet, will be used in an upcoming commit
Change-Id: I2a569f60fcc0815835615656b09670987036b848
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/18392
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Move the function that adds a power resource block from
i2c/generic to the acpi device code at src/arch/x86/acpi_device.c
so it can be used by more drivers.
BUG=chrome-os-partner:61233
TEST=verify SSDT table generation is unchanged
Change-Id: I0ffb61a4f46028cbe912e85c0124d9f5200b9c76
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/18391
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
The hybrid driver select by DRIVERS_LENOVO_HYBRID_GRAPHICS doesn't work
for t400/t500.
Replace it with a custom romstage implementation.
Tested on Lenovo T500 with dual graphics:
* Intel Native GFX init
* AMD VBios
* GNU Linux 4.8.13
* SeaBios as payload
* Discrete is working (44 W)
* Integrated is working (24 W)
* Switchable is working (34 W)
** Both GPUs are enabled, with Intel being connected to the panel
** DRI_PRIME allows to use AMD GPU
** ACPI doesn't seem to work (no vgaswitcheroo)
Depends on Change-Id: I4dc00005270240c048272b2e4f52ae46ba1c9422
Depends on Change-Id: If389016f3bb0c4c2fd0b826914997a87a9137201
Change-Id: I7496876e9b434d4a2388e1ede27ac604670339b7
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/18010
Tested-by: build bot (Jenkins)
Reviewed-by: Alexander Couzens <lynxis@fe80.eu>
|
|
Change-Id: I4ed7a164323a71d95a37ea754ec923ca0c5e6219
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: https://review.coreboot.org/18388
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Denis 'GNUtoo' Carikli <GNUtoo@no-log.org>
|
|
This company doesn't do custom hardware anymore and doesn't
host the sources anymore. We therefore point to the archived
sources instead.
Change-Id: I5ce4f6a468b852fc1d0947fe2b28a5297f14c437
Signed-off-by: Denis 'GNUtoo' Carikli <GNUtoo@no-log.org>
Reviewed-on: https://review.coreboot.org/11889
Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Tested-by: build bot (Jenkins)
|
|
Prmrr configuration is supported by Kabylake FSP-M with UPD provided.
It is required as one of the SGX initialization steps in BIOS.
BUG=chrome-os-partner:62438
BRANCH=NONE
TEST=Tested on Eve, verified uncore PRMRR MSRs get programmed to set
size and boot.
Change-Id: I2b3dc7c92487505165ee429bd1a37bd60ceac8f3
Signed-off-by: Robbie Zhang <robbie.zhang@intel.com>
Reviewed-on: https://review.coreboot.org/18361
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
It rewrites the results of receive enable stored in the upper nvram
region, to avoid running receive enable again.
Some debug info is also printed about the self-refresh registers.
(Not enforcing a reset here, since 0 does not necessarily mean it's
not in self-refresh).
Change-Id: Ib54bc5c7b0fed6d975ffc31f037b5179d9e5600b
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/17998
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Previously the raminit failed on hot reset and to work around this
issue it unconditionally did a cold reset.
This has the following issues:
* it's slow;
* when the OS issues a hot reset some disk drives expect their 5V
power supply to remain on, which gets cut off by a cold reset,
causing data corruption.
To fix this some steps in raminit must be ommited on the reset path.
This includes receive enable calibration.
To achieve this it stores receive enable results in RTC nvram for them
to be rewritten on the resume path.
Note: The same thing needs to be done on the S3 resume path.
Calling a hot reset after raminit "outb(0x6, 0cf9)" works.
Change-Id: I6601dd90aebd071a0de7cec070487b0f9845bc30
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/18009
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Add APIs and required parameters for creating Maxim 98927
and Realtek 5336 SSP endpoints in NHLT table.
BUG=chrome-os-partner:62051
BRANCH=None
TEST=check that NHLT table created is created properly
Change-Id: Ica302aab05c5364faf4923dc5327be8e8eaae8b4
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Signed-off-by: Naresh G Solanki <naresh.solanki@intel.com>
Signed-off-by: M Naveen <naveen.m@intel.com>
Reviewed-on: https://review.coreboot.org/18213
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Maxim 98927 kernel driver requires entries in the ACPI SSDT table,
add a SSDT generator as part of this driver.
BUG=chrome-os-partner:62051
BRANCH=None
TEST=After boot, dump and verify that the generated SSDT ACPI table has the
required entries.
Change-Id: Ic2d4d8449288bc00d085852220b2e1e7a208e9ef
Signed-off-by: Naresh G Solanki <naresh.solanki@intel.com>
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Signed-off-by: M Naveen <naveen.m@intel.com>
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Reviewed-on: https://review.coreboot.org/18211
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
eve is based on Kabylake SoC hence select the appropriate
config.
Change-Id: I756dda5a1924e83a02ac1cebb1907884f436a13f
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/18314
Tested-by: build bot (Jenkins)
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
poppy is based on Kabylake SoC hence select the appropriate
config.
Change-Id: Ie339a3991eeccb8a7dba983a2b5ab5d1c996ce9d
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/18313
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Currently there is no distinction between mainboards using
Skylake or Kabylake SoC, Add a config option for Kabylake
SoC to allow mainboards to explicitly select if they are
using it.
Change-Id: Ie7960bd81f88a223894afe3115ddc0bc637e4be4
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/18312
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Configure GRUB to build with boot time statistics. That allows users
to add that module to GRUB by adding `boottime` to the list of extra
modules.
Change-Id: I76a07e49aecb37652fe8c7d6a9421fd464424287
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-on: https://review.coreboot.org/18367
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
Some simple implementation of the MultiBoot protocol may not pass a
memory map (MULTIBOOT_FLAGS_MMAP missing in the flags) but just the two
values for low and high memory, indicated by the MULTIBOOT_FLAGS_MEMINFO
flag.
Support those kind of boot loaders too, instead of falling back to the
hard-coded values in lib_get_sysinfo().
Tested with a multiboot enhanced version of FILO.
Change-Id: I22cf9e3ec0075aff040390bd177c5cd22d439b81
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Reviewed-on: https://review.coreboot.org/18350
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
There are MSRs that are programmable per-core not per-thread, so add
a function to check whether current executing CPU is a primary core
or a "hyperthreaded"/secondary core. For instance when trying to
program Core PRMRR MSRs(per-core) with mp_init, cpu exception is thrown
from the secondary thread. This function was used to avoid that.
Potentially this function can be put to common code or arch/x86 or cpu/x86.
BUG=chrome-os-partner:62438
BRANCH=NONE
TEST=Tested on Eve, verified core PRMRR MSRs get programmed only on primary
thread avoiding exeception.
Change-Id: Ic9648351fadf912164a39206788859baf3e5c173
Signed-off-by: Robbie Zhang <robbie.zhang@intel.com>
Reviewed-on: https://review.coreboot.org/18366
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Implement the argc/argv passing as described in coreboot’s payload API:
http://www.coreboot.org/Payload_API
While at it, give the code some love by not needlessly trashing register
values.
Change-Id: Ib830f2c67b631b7216843203cefd55d9bb780d83
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Reviewed-on: https://review.coreboot.org/18336
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
|
|
Simplify the code by directly using the arguments on the stack as base
pointer relative memory references, instead of loading them into
intermediate registers first.
Make it more robust by preserving all callee saved registers mandated by
the C calling convention (and only those), namely EBP, EBX, ESI and EDI.
Don't assume anything about the register state when the called function
returns -- beside the segment registers and the stack pointer to be
still the same as before the call.
Change-Id: I383d6ccefc5b3d5cca37a1c9b638c231bbc48aa8
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Reviewed-on: https://review.coreboot.org/18335
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
|
|
According to coreboot’s payload API [1], the called payload should be
able to return a value via %eax. Support this by changing the prototype
of start_main() and pass on the return value of main() to the caller
instead of discarding it.
[1] https://www.coreboot.org/Payload_API
Change-Id: I8442faea19cc8e04487092f8e61aa4e5cba3ba76
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Reviewed-on: https://review.coreboot.org/18334
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
According to coreboot’s payload API [1] the argc value should be passed
at stack offset 0x10, so we need to push a dummy value to comply to the
API.
[1] https://www.coreboot.org/Payload_API
Change-Id: Id20424185a5bf7e4d94de1886a2cece3f3968371
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Reviewed-on: https://review.coreboot.org/18333
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Add support for generating digitizer node in SSDT using wacom i2c
driver.
BUG=None
BRANCH=None
TEST=Verified that the node shows up in SSDT.
Change-Id: If7e1e2463778c2ff7263eff995def149457edcde
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/18373
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Use the newly added SPI SSDT generator for adding FPC device.
BUG=chrome-os-partner:59832
BRANCH=None
TEST=Compiles successfully. Verified that the SSDT entry matches the
entry in mainboard.asl
Change-Id: I1b3c33f2b4337735a9725dd4eb6193b2455962d7
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/18343
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Similar to I2C driver, add support for generating SPI device and
required properties in SSDT for ACPI.
BUG=chrome-os-partner:59832
BRANCH=None
TEST=Compiles succesfully. Verified SPI device generated in SSDT on
poppy.
Change-Id: Ic4da79c823131d54d9eb3652b86f6e40fe643ab5
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/18342
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Add a new PCI driver for SPI devices with supported PCI ids. Also,
provide a translation table to convert struct device structure into SPI
bus number.
BUG=chrome-os-partner:59832
BRANCH=None
TEST=Compiles successfully
Change-Id: If860eb819f2ce5ae5443f808b356af57f86c52be
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/18341
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
scan_smbus routine does not perform any smbus specific operation. Thus,
rename the routine to scan_generic_bus so that it can be used by other
buses like SPI. Add a wrapper scan_smbus to allow other users of smbus
scan to continue working as before.
BUG=chrome-os-partner:59832
BRANCH=None
TEST=Compiles successfully
Change-Id: I8ca1a2b7f2906d186ec39e9223ce18b8a1f27196
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/18363
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Add support for a new "SPI" device type in the devicetree to bind a
device on the SPI bus. Allow device to provide chip select number for
the device as a parameter.
Add spi_bus_operations with operation dev_to_bus which allows SoCs to
define a translation method for converting "struct device" into a unique
SPI bus number.
BUG=chrome-os-partner:59832
BRANCH=None
TEST=Compiles successfully.
Change-Id: I86f09516d3cddd619fef23a4659c9e4eadbcf3fa
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/18340
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins)
|
|
Update sconfig lex and yacc files to add support for a new "SPI" device
type in the devicetree. SPI device takes only parameter i.e. chip select
number for the device on the SPI bus.
Re-generate the shipped files for sconfig using flex 2.6.0 and bison
3.0.4 (make CONFIG_SCONFIG_GENPARSER=1). Clean up local paths that leak
into generated files.
BUG=chrome-os-partner:59832
BRANCH=None
TEST=Compiles successfully.
Change-Id: If0831e25b3e4ed87827ad92356d7bf47b6387884
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/18339
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Provide implementation of get_config routine for GSPI controller on
skylake platforms.
BUG=chrome-os-partner:59832
BRANCH=None
TEST=Compiles successfully.
Change-Id: I5170076c15d72a7f29acd0989acef5b9149e2ba0
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/18338
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Add a new callback to spi_ctrlr structure - get_config - to obtain
configuration of SPI bus from the controller driver. Also, move common
config definitions from acpi_device.h to spi-generic.h
BUG=chrome-os-partner:59832
BRANCH=None
TEST=Compiles successfully
Change-Id: I412c8c70167d18058a32041c2310bc1c884043ce
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/18337
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
HALO SOC
Add CPU, PCH, MCH, IGD, XHCI and UART IDs for SKL/KBL HALO SOC
Change-Id: I6a44d55d1588d2620bd1179ea7dc327922f49fd7
Signed-off-by: Sooi, Li Cheng <li.cheng.sooi@intel.com>
Reviewed-on: https://review.coreboot.org/18028
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
|
|
The pointer to write the return value to is in %ecx, not %eax. Writing
to (%eax) leads to memory corruptions as %eax holds the return value,
e.g. would write zero to address zero for a "successful" returning
payload.
Change-Id: I82df27ae89a9e3d25f479ebdda2b50ea57565459
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Reviewed-on: https://review.coreboot.org/18332
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
According to coreboot’s payload API [1] the magic value passed to the
payload should be 0x12345678, not 12345678. Fix that.
[1] https://www.coreboot.org/Payload_API
Change-Id: I10a7f7b1a4aec100416c5e7e4ba7f8add10ef5c5
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Reviewed-on: https://review.coreboot.org/18331
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This commit makes a basic adjustment for GPIOs, device tree, flash map and
MRC settings. With these basic settings the mainboard boots into
Linux lubuntu 4.8.0-22-generic using SeaBIOS. More adjustments will follow.
Change-Id: Ia920d236814f2e6a9b777dd1e4b4feef0ddf7721
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/18292
Tested-by: build bot (Jenkins)
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
Create the initial Sand variant which refers to the Reef.
Sand is APL board that derives from reference board Reef.
BRANCH=master
BUG=chrome-os-partner:62200
TEST=Build (as initial setup)
Signed-off-by: YH Lin <yueherngl@chromium.org>
Change-Id: Iba8c5653b6176676c759d2b48063f0c0c6cde625
Reviewed-on: https://review.coreboot.org/18324
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
As per BWG, CPU MP Init (loading ucode) should be done prior
to BIOS_RESET_CPL. Hence, pull MP Init to BS_DEV_INIT_CHIPS Entry
(before FSP-S call).
BUG=chrome-os-partner:62438
BRANCH=NONE
TEST=Boot to OS with all threads enabled.
Change-Id: Ia6f83d466fb27e1290da84abe7832dc814b5273a
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/18287
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
The four options are only used in X86:
- BOOTBLOCK_SIMPLE
- BOOTBLOCK_NORMAL
- BOOTBLOCK_SOURCE
- SKIP_MAX_REBOOT_CNT_CLEAR
Move them all into src/arch/x86/Kconfig - this puts them in the chipset
menu instead of general setup.
Verified that this makes no significant changes to any config file.
Change-Id: I2798ef67a8c6aed5afac34322be15fdf0c794059
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/17909
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
|
|
For boolean types, 'n' is the default default value - it doesn't
NEED to be set. If it IS set, it prevents a later default from
being set. So by removing the 'default n' statements from the
early symbols, they can be overridden other places in the tree.
Verified that this makes no significant changes to any config file.
Change-Id: I1b5b66bd8a3df8154a348b5272c56c88829b3ab4
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/17908
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
The existing default path of PCI0.LPCB is missing the \_SB prefix and prevents Linux from detecting the TPM.
This is assuming that normally the LPCB device is most commonly on \_SB.PCI0.LPCB.
SSDT excerpt without the patch:
"""
DefinitionBlock ("", "SSDT", 2, "CORE ", "COREBOOT", 0x0000002A)
{
External (_SB_.PCI0.GFX0, DeviceObj)
[...]
External (_SB_.PCI0.SATA, DeviceObj)
External (PCI0.LPCB, DeviceObj)
[...]
Scope (PCI0.LPCB)
{
Device (TPM)
[...]
Scope (\_SB.PCI0.GFX0)
{
Method (_DOD, 0, NotSerialized) // _DOD: Display Output Devices
[...]
"""
SSDT excerpt with the patch:
"""
DefinitionBlock ("", "SSDT", 2, "CORE ", "COREBOOT", 0x0000002A)
{
External (_SB_.PCI0.GFX0, DeviceObj)
[...]
External (_SB_.PCI0.LPCB, DeviceObj)
[...]
External (_SB_.PCI0.SATA, DeviceObj)
[...]
Scope (\_SB.PCI0.LPCB)
{
Device (TPM)
[...]
Scope (\_SB.PCI0.GFX0)
{
Method (_DOD, 0, NotSerialized) // _DOD: Display Output Devices
[...]
"""
After the patch the TPM shows up in /sys/bus/acpi/devices/PNP0C31:00.
Previously it was missing and not detected by the kernel.
Change-Id: I615b4873ca829a859211403c84234d43d60f2243
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Reviewed-on: https://review.coreboot.org/18315
Tested-by: build bot (Jenkins)
Reviewed-by: Nicola Corna <nicola@corna.info>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Change-Id: I7c1e3cf558d447838819b4d6a63d93d48d5f13e0
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/18316
Tested-by: build bot (Jenkins)
Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
This reverts commit 32997fb0bcb9f4183789331a91fd83138776b96f.
This change is breaking I2S audio on Kabylake platforms so
revert the change to fix audio.
BUG=chrome-os-partner:61548,chrome-os-partner:61009
TEST=manual testing on Eve P1 system
Change-Id: I3212c8be83078ed57e38501386605e67b87d5bd0
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/18360
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
|
|
Change touchpad HID to use with the Google Centroiding Touchpad driver.
BUG=chrome-os-partner:61088
TEST=`emerge-eve coreboot`
Change-Id: I199ff46f1a93d3eccc8c694742585dcf37b2373f
Signed-off-by: Wei-Ning Huang <wnhuang@google.com>
Reviewed-on: https://review.coreboot.org/18359
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Some variants need the internal pull resistor on GPIO_SSUS_40
set explicitly to pull down rather than disabling the pull,
in order for the ram-id to be read correctly via GPIO.
Correct this by adding a function to enable and set the internal pull
and define its use as needed in the board's variant.h.
Chromium source:
branch: firmware-gnawty-5216.239.B
/src/soc/intel/baytrail/baytrail/gpio.h#418
/src/mainboard/google/gnawty/romstage.c#60
Test: boot 4GB Candy board and observe correct RAM id, amount detected
Change-Id: I8823c27385f4422184b5afa57f6048f7ff2a25ab
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/18309
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Those are the result from tracing what linux or the option rom do
but are not needed here.
TESTED on Thinkpad X60.
Change-Id: I4297a78c4ab6a19ef6161778c993fc3f3fb08c7e
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/18294
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Change-Id: I3395e274e0ba43de7e7306daedeb26c75de65ee1
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/18327
Tested-by: build bot (Jenkins)
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Poppy doesn't support 8042 keyboard. Select
NO_FADT_8042 to disable 8042 in FADT header.
Kernel will not try to access 8042 region
if 8042.FADT=0
BUG=chrome-os-partner:61858
TEST=Boot OS and verify FADT 8042 flag
Change-Id: I00182eb4b059d4d9f0705d349dc98651e3955f0d
Signed-off-by: Jenny TC <jenny.tc@intel.com>
Reviewed-on: https://review.coreboot.org/18311
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Kernel relies on FADT 8042 flag to enable/disable
8042 interface. If FADT reports 8042 capability and
8042 (/PS2) capability is actually disabled by coreboot,
kernel would assume the presence of 8042 based on the
FADT flag. This results in undesired system power off when
kernel tries to access the 8042 memory region. To address
this, CONFIG_NO_FADT_8042 was added to selectively
disable 8042 on FADT.
BUG=chrome-os-partner:61858
TEST=Boot OS and verify FADT 8042 flag
Change-Id: Ic80b3835cb5cccdde1203e24a58e28746b0196fc
Signed-off-by: Jenny TC <jenny.tc@intel.com>
Reviewed-on: https://review.coreboot.org/18307
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Update DPTF parameters based on thermal team test result.
1. Update TSR2 trigger points.
TSR2 passive point: 70, critical point: 90
2. Set PL2 Max to 15W.
BUG=chrome-os-partner:61383
BRANCH=reef
TEST=build, boot on snappy, and verified by thermal team
Change-Id: I8d01d6c1d7eabd359ceb131f3cd10965d4ac2c42
Signed-off-by: Wisley Chen <wisley.chen@quantatw.com>
Reviewed-on: https://review.coreboot.org/18318
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Void pointer arithmetics are forbidden in standard C but GCC has
an extension that allows it.
Change-Id: I43029b2ab2f7709b8e1ba85eb05c31341b8ac16f
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/18293
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Performance degradation seen with current PL1 throttling rate as 8
seconds for TSR1 sensor with Aquarium workload. After fine tuning PL1
throttling rate to 15 seconds, fps score improved.
BUG=chrome-os-partner:60038
BRANCH=reef
TEST=Built and tested on electro system
Change-Id: I5cdebb08e00f0f28b88f1c6b2b1cafaeb8cdb453
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/18317
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Venkateswarlu V Vinjamuri <venkateswarlu.v.vinjamuri@intel.com>
|
|
There will be more follow-up changes.
BUG=chrome-os-partner:62377
BRANCH=None
TEST=emerge-scarlet coreboot libpayload
Change-Id: I9ca45598ff0ab12bf8063d16a86be564cf509390
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: a020a9ba1228b15599e202972df0096f58b1b31c
Original-Change-Id: I4804239483f8b35bc3703aa62c2a8fd642e0234a
Original-Signed-off-by: philipchen <philipchen@google.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/433039
Original-Commit-Ready: Philip Chen <philipchen@chromium.org>
Original-Tested-by: Philip Chen <philipchen@chromium.org>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/18296
Tested-by: build bot (Jenkins)
Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
|
|
It's an attempt to consolidate the access code, even if there are still
multiple implementations in the code.
Change-Id: I4b2b9cbc24a445f8fa4e0148f52fd15950535240
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Reviewed-on: https://review.coreboot.org/18265
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Since it checks for DDR3 style checksums, it's a more appropriate name.
Also make its configuration local for a future code move.
Change-Id: I417ae165579618d9215b8ca5f0500ff9a61af42f
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Reviewed-on: https://review.coreboot.org/18264
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
|
|
Change-Id: Ic8e850bdf75d38fc061fb3a8c55d38bcf09c305a
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Found-by: Coverity Scan #1129146
Reviewed-on: https://review.coreboot.org/17886
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Also make sure that no board changes behaviour because of that by adding
a static assert.
TEST=abuild over all builds still succeeds (where it doesn't if
DIMM_SPD_SIZE isn't set to 128 bytes for boards that use the
device/dram code).
Change-Id: Iddb962b16857ee859ddcf1b52d18da9b3be56449
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Reviewed-on: https://review.coreboot.org/18254
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
|
|
Shorten field names of struct cbmem_console since saying "buffer_" in
front of everything is redundant and we can use the gained space to save
some line breaks in the code later. This also aligns the definition with
the version in libpayload.
Change-Id: I160ad1f39b719ac7e912d0466c82a58013cca0f9
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/18299
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Update FSP UPD header files as per version 1.6.0.
Below UPDs are added to FspsUpd.h:
* DelayUsbPdoProgramming
* MeUnconfigIsValid
* CpuS3ResumeDataSize
* CpuS3ResumeData
CQ-DEPEND=CL:*322871,CL:*323186,CL:*322870
BUG=None
BRANCH=None
TEST=Build and boot on RVP3 and poppy
Change-Id: Id51a474764a28eec463285757d0eb8ec7ca13fd1
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-on: https://review.coreboot.org/18289
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
The FSP UPD offsets and the corresponding structure size do not match,
CpuConfigData.h needs an update to align the same. Hence update the
header file based on FSP version 1.4.0.
BUG=chrome-os-partner:61548
BRANCH=none
TEST=Built and booted KBLRVP and verify that all UPDs are in sync in
both coreboot and FSP.
Change-Id: I5ef7cbb569c3d1a44e7846717201952a0acf12ab
Signed-off-by: Barnali Sarkar <barnali.sarkar@intel.com>
Reviewed-on: https://review.coreboot.org/18285
Tested-by: build bot (Jenkins)
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
The apollolake boards don't have an me.bin proper, but they still have
descriptor regions which need to be locked down. Therefore, remove the
restriction of HAVE_ME_BIN from LOCK_MANAGEMENT_ENGINE.
BUG=chrome-os-partner:62177
TEST=For apollolake one can select LOCK_MANAGEMENT_ENGINE.
Change-Id: I73aab3a604ec25cd56d760bf76cc21c5a298799e
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/18304
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Dump the CSE status registers for potential debugging purposes.
Explicitly call out manufacturing mode of the part since it's
important shipping devices ensure manufacturing mode is locked
down. Intel is planning on writing a common driver so a complete
status -> string dumps was not done because (surprise surprise)
not all the fields are equal with previous implementations.
BUG=chrome-os-partner:62177
BRANCH=reef
TEST=Booted and noted dump of CSE status registers.
Change-Id: I71d15722bb193877f1569c1d3e7f441302f5bd14
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/18303
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This fixes an issue on systems where the S3 state in the pm1 control
registers are not cleared when vboot determines recovery mode is
required on an S3 resume. The EC code will reboot the system knowing
that the EC was in RW. However, on subsequent entry into romstage the
S3 path will be taken and fails to recover cbmem -- forcing another
reboot. To work around that, signal to the platform a reboot is
happening and let the platform perform the necessary fix ups to the
register state.
BUG=chrome-os-partner:62627
Change-Id: Ic144b11b4968c92a1273b8d9eb9dc10f0056bf3d
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/18295
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Reef is a convertible add support for sending Tablet mode switch
changes from EC to AP.
Change-Id: I6dfddbfdb5a2ffbdfd77c5f49602bf68e9693a06
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-on: https://review.coreboot.org/18277
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Eve is a convertible add support for sending Tablet mode switch
changes from EC to AP.
Change-Id: I35133ebc1439852d0ceb88d7d679b37356b0869d
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-on: https://review.coreboot.org/18276
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Add a new driver GOOG0006 to report tablet switch
to user space.
On glados based convertible, check that with a new kernel driver
(cros_ec_tbmc) that evtest collects tablet switch changes.
Change-Id: I6821eaac1feb6c182bc973aaa2f747e687715afb
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/430951
Reviewed-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/18173
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Change-Id: I14c044bb32713ef4133bce8a8238a2bc200c4959
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/18085
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Options with no prompt can go anywhere in the tree with the same
dependencies and they have the same effect. Moving them lower in
the tree allows the default values to be overridden by other Kconfig
files.
This patch just moves options with default values that aren't 'n'. The
'n' options are just removed in the next patch, since they aren't needed.
Verified that this makes no significant changes to any config file.
Change-Id: I46175756b937a241edba87dbf70ce1be851fa89d
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/17907
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
The WAK_STS bit is not set in a wake from G3, so the check for this
bit needs to only be done when checking for a wake from S3.
This change correctly enables the keyboard backlight in wake from G3
and only does not enable it during a wake from S3.
BUG=chrome-os-partner:58666
TEST=Use Refresh+Power to issue hard reset and ensure that the keyboard
backlight turns on like it does when waking from S5. Also force enter
hibernate with Alt+VolumeUp+H and then power back up and ensure that
the keyboard backlight is enabled when booting.
Change-Id: I44045950e38aa5e5ae96a79385d604791852c7e6
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/18280
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
For Kconfig options that we might want to override the default,
move the fallback default to the bottom of the file. This allows
the default to be set anywhere else, without requiring a select.
This is especially important for non-boolean symbols, which can't
have their defaults overridden in the Kconfig. Those can only be
updated in a saved config file.
Verified that this makes no significant changes to any config file.
Change-Id: I66034f356428f4ccd191d7420baf888edd5216dc
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/17906
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Given a specification of bitfields defined e.g. as follows:
specfile:
{
"field1" : 8,
"field2" : 4,
"field3" : 4
}
and a set of values for setting defaults:
setterfile:
{
"field1" = 0xff,
"field2" = 0xf,
"field3" = 0xf
}
You can generate a binary packed blob as follows:
./blobtool specfile setterfile binaryoutput
binaryoutput: ff ff
The reverse is also possible, i.e. you can regenerate the setter:
./blobtool -d specfile binaryoutput setterorig
setterorig:
# AUTOGENERATED SETTER BY BLOBTOOL
{
"field1" = 0xff,
"field2" = 0xf,
"field3" = 0xf
}
This tool comes with spec/set files for X200 flash descriptor
and ICH9M GbE region, and can be extended or used to decompile
other data blobs with known specs.
Change-Id: I744d6b421003feb4fc460133603af7e6bd80b1d6
Signed-off-by: Damien Zammit <damien@zamaudio.com>
Reviewed-on: https://review.coreboot.org/17445
Tested-by: build bot (Jenkins)
Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
When guado/rikku/tidus were rolled into jecht, an error was
made in set_power_led() as guado/rikku set the polarity
differently than tidus. Fix the power LED for guado/rikku
by setting the polarity correctly.
Test: boot guado/rikku and observe proper function of power LED
under S0, S3, and S5 power states.
Change-Id: I23072ac60bc9683776f748ca1326d98257c3c54f
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/18249
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Bit 16 in BLC_PWM_CTL enables brightness controls, but the
current value is generic. Use the proper value, obtained
by reading BLC_PWM_CTL while running the VBIOS.
Change-Id: Ib273359e1c285b405a9bb26fc217c2f7e255b99f
Signed-off-by: Francis Rowe <info@gluglug.org.uk>
Reviewed-on: https://review.coreboot.org/10624
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Reason for revert:
Pyro has two touchscreen sources: WACOM/ELAN.
It will not have both touchscreen IC in one system at the same time.
So the "probed" property of WACOM i2c device is mandatory to set for kernel
to know whether it exists before driver initializes it.
Otherwise in ELAN case, when driver fails to init WACOM i2c device, ACPI _OFF
will be invoked to set GPIO#152 low to cut off power.
BUG=chrome-os-partner:62371
BRANCH=reef
TEST=emerge-pyro coreboot
Change-Id: I30f467bd8720d959686dc14f7877e6bc11ea6213
Signed-off-by: Kevin Chiu <Kevin.Chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/18291
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This also selects RELOCATABLE_RAMSTAGE and
CACHE_RELOCATABLE_RAMSTAGE_OUTSIDE_CBMEM by default on Haswell.
Change-Id: I50b9ee8bbfb3611fccfd1cfde58c6c9f46b189ca
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/18232
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
This change fixes the two sets of pins that were swapped in the
map of DQS signals from CPU to DRAM for channel 1.
Although this does not appear to have any impact to the system it
does result in different register values for DQS pin mapping that
are programmed inside FSP.
BUG=chrome-os-partner:58666
TEST=This fix was verified against the current schematic and using
FSP debug output.
Change-Id: I45b821071ba287493b3b13204b7f5b38e06eee75
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/18279
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
The selection of the SSC reference frequency for LVDS was based on a
completely unrelated clock.
The `ssc_freq` flag should be set when the SSC reference runs at a
different frequency than the general display reference clock (DREF).
For most platforms, there is no choice, i.e. for i945 and gm45 the SSC
reference always differs from the display reference clock (i945: 66Mhz
SSC vs. 48MHz DREF; gm45: 100MHz SSC vs. 96Mhz DREF), for Nehalem and
newer, it's the same frequency for SSC/non-SSC (120MHz). The only,
currently supported platform with a choice seems to be Pineview, where
the alternative is 100MHz vs. the default 96MHz.
Change-Id: I7791754bd366c9fe6832c32eccef4657ba5f309b
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/18186
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
same change as I49935e659bf67225d3f5db1b06acc2cd046dcd74
this is required for poppy board as well.
GPIO GPP_D22 controls the I2S buffer for isolating the I2S signals
when doing GPIO-driven I2S. This needs to be high by default so
the DSP can drive these signals, instead of low where it is enabled
for GPIO-driven I2S and the DSP cannot drive these signals.
BUG=None
BRANCH=None
TEST=play test sound in OS over internal speaker
Change-Id: I1695e9198f8f78e9c5ad6df6c1ac073ac1762c6b
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/18282
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
GPIO GPP_D22 controls the I2S buffer for isolating the I2S signals
when doing GPIO-driven I2S. This needs to be high by default so
the DSP can drive these signals, instead of low where it is enabled
for GPIO-driven I2S and the DSP cannot drive these signals.
BUG=chrome-os-partner:58666
TEST=play test sound in OS over internal speaker
Change-Id: I49935e659bf67225d3f5db1b06acc2cd046dcd74
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/18281
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
The me_cleaner option is available on multiple platforms:
* Sandy and Ivy Bridge (well tested by multiple users).
* Skylake and Braswell (tested).
* Haswell, Broadwell and Bay Trail (untested).
The untested platforms have been included anyways because all the
firmwares are very similar and Intel ME/TXE probably behaves in the
same way.
Change-Id: I46f461a1a7e058d57259f313142b00146f0196aa
Signed-off-by: Nicola Corna <nicola@corna.info>
Reviewed-on: https://review.coreboot.org/18206
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Hide the IGD to make sure ramstage doesn't detect it.
Change-Id: If389016f3bb0c4c2fd0b826914997a87a9137201
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/18194
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Add VFCT table to provide PCI Optiom Rom for
AMD graphic devices.
Useful for GNU Linux payloads and embedded dual GPU systems.
Tested on Lenovo T500 with AMD RV635 as secondary gpu.
Original Change-Id: I3b4a587c71e7165338cad3aca77ed5afa085a63c
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Change-Id: I4dc00005270240c048272b2e4f52ae46ba1c9422
Reviewed-on: https://review.coreboot.org/18192
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
With coreboot 4.4 switched to "Descriptor mode" for Lenovo T500
it automatically unlocks all flash regions. For Gbe region
the "Requester ID" was hardcoded resulting in *dead* Gbe.
Keep board specific "Requester ID" while unlocking Gbe region.
Allows Lenovo T500 to boot with IFD "Descriptor mode" with unlocked
flash regions.
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Change-Id: Ia4b5d1928e84bee42182fc83020e3a13fadc93c4
Reviewed-on: https://review.coreboot.org/18055
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
This patch sets PL2 override value to 15W in RAPL registers.
BUG=chrome-os-partner:62110
BRANCH=reef
TEST=Apply new firmware to evaluate Octane benchmark score.
Change-Id: I51734051586753677129314b5273fb275c74f5d2
Signed-off-by: Harry Pan <harry.pan@intel.com>
Reviewed-on: https://review.coreboot.org/18283
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
|
|
This allows for defaults to be applied to CMOS parameters
when cmos checksum is incorrect.
This probably results in changed cmos settings for current users of
these targets.
Change-Id: Ifec0093f4b0dbaa51b96812a041f0eaf5c58ee86
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/17041
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Activate the IOMMU for the ASUS F2A85-M LE board.
Enable the IOMMU in `devicetree.cb` and build AGESA IOMMU code by
enabling the option in `buildOpts.c`.
ACPI and MPTABLES interrupt routers are already present since they are
syminks to the F2A85-M version.
```
$ uname -a
Linux nukunuku 4.8.5 #35 SMP Sun Oct 30 19:34:55 CET 2016 x86_64 GNU/Linux
$ lspci -s 0.2
00:00.2 IOMMU: Advanced Micro Devices, Inc. [AMD] Family 15h (Models 10h-1fh) I/O Memory Management Unit
$ dmesg | grep -i IOMMU
ACPI: IVRS 0x00000000BFFAFF70 000070 (v02 AMD AMDIOMMU 00000001 AMD 00000000)
AMD-Vi: Applying erratum 746 workaround for IOMMU at 0000:00:00.2
iommu: Adding device 0000:00:01.0 to group 0
[...]
iommu: Adding device 0000:00:18.5 to group 9
iommu: Adding device 0000:03:00.0 to group 8
AMD-Vi: Found IOMMU at 0000:00:00.2 cap 0x40
AMD IOMMUv2 driver by Joerg Roedel <jroedel@suse.de>
```
Change-Id: I6049fcfad53d16a99495d7a8fbc584c71e371d73
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Reviewed-on: https://review.coreboot.org/18259
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Adds checks for OpenBSD in all the places that were already checking for
NetBSD. This fixes e.g.:
ec.c:21:20: error: sys/io.h: No such file or directory
which was caused by defaulting to Linux.
Also, OpenBSD calls its amd64 iopl amd64_iopl instead of x86_64_iopl.
This change just defines iopl appropriately depending on the
OS and architecture.
TEST=Build on OpenBSD 6.0 or -current from 2017-01-25.
Change-Id: If6d92a9850c15cd9f8e287cc4f963d3ff881f72c
Signed-off-by: Steven Dee <i@wholezero.org>
Reviewed-on: https://review.coreboot.org/18260
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
This mainboard is based on Intel's Leafhill CRB with Apollo Lake
silicon. In a first step, it concerns only a copy of intel/leafhill
directory with minimum changes. Special adaptations for MC APL1
mainboard will follow in separate commits.
Change-Id: If0b8a2bc21c99c3be4e6043e8febfb1b91ff0a63
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/18272
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Brenton Dong <brenton.m.dong@intel.com>
|
|
Change depthcharge to not require a board-specific config file for
libpayload. If the Kconfig option is selected, use the settings
in libpayload/configs/defconfig instead.
Change-Id: I4fd1a5915472f28e757c62f3f2415716f1fdfc71
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/18271
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Add new ChromeOS devices banjo, candy, clapper, glimmer, gnawty,
heli, kip, orco, quawks, squawks, sumo, swanky, and winky using
their common reference board (rambi) as a base.
Chromium sources used:
firmware-banjo-5216.334.B 32ec493 [chromeos: vboot_loader: Set...]
firmware-candy-5216.310.B 519ff11 [baytrail: Preserve VbNv around...]
firmware-clapper-5216.199.B 80d55e3 [baytrail: add code for...]
firmware-glimmer-5216.198.B fae0770 [baytrail: add code for...]
firmware-gnawty-5216.239.B 952adb7 [Gnawty/Olay: Add 2nd source...]
firmware-heli-5216.392.B f1f3604 [helis: Lock ME / TXE section...]
firmware-kip-5216.227.B db3c5d9 [kip: update spd for for MT41K256M16*]
firmware-orco-5216.362.B 76f1651 [Orco: Adjust rx delay for norm.]
firmware-quawks-5216.204.B edb60c9 [Quawks: Update SPD data]
firmware-squawks-5216.152.B c6573dc [Squawks: Update SPD data]
firmware-sumo-5216.382.B c62b6f23 [Ninja, Sumo: Add SPD source...]
firmware-swanky-5216.238.B 233b2a7 [Swanky: update SPD table]
firmware-winky-5216.265.B ce91ffc [Add to support HT Micron...]
The same basic cleanup/changes are made here as with the initial BYT
variant commit:
- remove unused ACPI trackpad/touchscreen devices
- correct I2C addresses in SMBIOS entries
- clean up comment formatting
- remove ACPI device for unused light sensor
- switch I2C ACPI devices from edge to level triggered interrupts,
for better compatibility/functionality (and to be consistent
with other recently-upstreamed ChromeOS devices)
- Micron 2GB SPD file for kip with updated values renamed to distinguish
from same file used by other boards
Change-Id: Ic66f9b539afb5aff32c4c1a8563f6612f5a2927c
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/18164
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Add the capability for specifying which version of depthcharge to
checkout and build. This is similar to the existing feature for
SeaBIOS.
The depthcharge makefile already contains some structure for checking
out master vs. stable however the calling Makefile.inc ingored this
feature. Add the command-line variable assignment for these, along
with a tree-ish for any revision.
Change-Id: I99a5b088cb0ebb29e5d96a84217b3bfa852de8ac
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/18270
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Depending on the commit to build, depthcharge may have a different
target name (depthcharge vs. depthcharge_unified). Add some logic
to determine which name should be used based on the commit ID
being requested.
Change-Id: I05b853934d13696f4bd0d79d53ff6c5f59096d1c
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/18269
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Drop the _unified moniker from the depthcharge build. The payload
and coreboot have drifted out of sync and there is no longer a
non-unified depthcharge.
This patch corresponds with the depthcharge change:
https://review.coreboot.org/cgit/depthcharge.git/commit/?id=74a0739
Change-Id: I8d028b14d2eee63dfdc9d3dd63695f1c58ea7984
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/18268
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
That status isn't needed and making it non-static helps gcc 4.9.2 (or
any compiler that insists on "standard C" behaviour with global const
initializers)
Change-Id: Ib1fbd5213d262e653f31564b106095b4a28292f6
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/18266
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
We rely on gnu make, so we can expect the jobserver to be around in
parallel builds, too. Avoids some make warnings and slightly speeds up
the build if those sub-makes are executed (eg for arm-trusted-firmware
and vboot).
Change-Id: I0e6a77f2813f7453d53e88e0214ad8c1b8689042
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/18263
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Speed up the execution of this script from ~6 seconds to ~1 on my
system.
There are some changes to its output, but they're actually _more_
correct: so far, architectures without compiler support kept compiler
options for architectures that ran successfully earlier.
Change-Id: I0532ea2178fbedb114a75cfd5ba39301e534e742
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/18262
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Reorder the items to minimize the differences.
Change-Id: I745ec70a990f997d87c2a0b6164ae127eb694ddf
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: https://review.coreboot.org/17438
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
