| Age | Commit message (Collapse) | Author |
|---|
|
Add a function to read the current state of Deep S5 configuration
and indicate if it is enabled (for AC and/or DC) or disabled.
This is similar to the existing function that checks Deep S3
enable state.
BUG=b:36042662
BRANCH=none
TEST=tested with subsequent commits to check Deep S5 state at boot
and filter event log messages if it is enabled.
Change-Id: I4b60fb99a99952cb3ca6be29f257bb5894ff5a52
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/18663
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Add options to the skylake chip config that will allow tuning the
various settings that can affect acoustics with the CPU and its VRs.
These settings are applied inside FSP, and they can adjust the slew
slew rate when changing voltages or disable fast C-state ramping on
the various CPU VR rails.
BUG=b:35581264
BRANCH=none
TEST=these are currently unused, but I verified that enabling the
options can affect the acoustics of a system at runtime.
Change-Id: I6a8ec0b8d3bd38b330cb4836bfa5bbbfc87dc3fb
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/18662
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
|
|
A new board revision is making use of two previously unused GPIOs
to drive BOOT/RESET pins to an on-board MCU.
The reset pin is open drain so it is set as input by default, and
the boot pin is driven low by default.
Since these are UART0 pins they also need to be set up again after
executing FSP-S as it will change them back to native mode pins.
BUG=b:36025702
BRANCH=none
TEST=manual testing on reworked board, toggling GPIOs to put
the MCU into programming mode.
Change-Id: Id6f0ef2f863bc1e873b58e344446038786b59d25
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/18661
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
|
|
Allows to use SSE and floating point in payloads without digging to
much into x86 assembly code.
Tested on Lenovo T500 (Intel Core2Duo).
Both floating point operation and SSE is properly working.
Change-Id: I4a5fc633f158de421b70435a8bfdc0dcaa504c72
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/18345
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Change-Id: Ic5c92d9a2d8bb040a04602e5da2cd37a2ae8db95
Signed-off-by: Stefan Tauner <stefan.tauner@gmx.at>
Reviewed-on: https://review.coreboot.org/18052
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Fine tune USB2, need to override the following registers.
port#1:
PERPORTPETXISET=7
PERPORTTXISET=0
BUG=b:35858164
BRANCH=reef
TEST=built, measured eye diagram on snappy, and reviewed by intel
Change-Id: I461cf8f032b4e70abc9707e6cd3603a62cee448f
Signed-off-by: Wisley Chen <wisley.chen@quantatw.com>
Reviewed-on: https://review.coreboot.org/18590
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This adds support for the Wildcat Point LP for intelmetool.
When the tool detected a Wildcat Point LP,
then the ME will be reported as difficult-to-remove.
Change-Id: I35423db11cdc1e21e7f02ce90dace7fb4d236c45
Signed-off-by: Huan Truong <htruong@tnhh.net>
Reviewed-on: https://review.coreboot.org/18575
Tested-by: build bot (Jenkins)
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
|
|
The intel ME checker tool would segfault if it reaches the end of
the loop without having the dev pointer set. This happens when
it gets to the end of the previous loop without knowing what to do
with any of the devices it sees.
This patch makes sure the pointer is not NULL before accessing it.
Change-Id: Ia13191799d7e00185947f9df5188cb2666c43e2a
Signed-off-by: Huan Truong <htruong@tnhh.net>
Reviewed-on: https://review.coreboot.org/18573
Tested-by: build bot (Jenkins)
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
- Fix whitespace: Change some spaces to tabs
- Add myself as an abuild maintainer
- Add util/xcompile and util/genbuild_h to the BUILD SYSTEM section
- Add new sections for utilities: docker, toolchain, and git
- Remove GENERIC DRAM section
- Remove the mailing list. We don't want it to be added as a reviewer.
Change-Id: I78692fcac174d7b7c4d65911c85e4e2dacefcfc0
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/18578
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
No board with binaryPI currently supports HAVE_ACPI_RESUME. For
platforms with PSP the approach is also very different from what
we previously had here.
Furthermore, s3_resume.[ch] files under cpu/amd/pi do not
distinguish between NonVolatile and Volatile buffers of S3 storage.
This means the Volatile buffer that is maintained and available in
CBMEM is unnecessarily copied to SPI flash. This has been fixed on
open-source AGESA directory, so development of S3 suspend support
with binaryPI is better continued with that.
Unfortunately there are further complications and indications that
open-source AGESA may have always had a low-memory corruption
issue. This has to be investigated separately before restoring
or claiming S3 is supported on binaryPI.
Change-Id: I81585fff7aae7bcdd55e5e95bc373e0adef43ef0
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/18501
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
|
|
None of the boards currently have HAVE_ACPI_RESUME and
and ACPI S3 support calls should not appear under board
directories anyways.
Change-Id: I1abd40ddba64be25b823abf801988863950c1eb5
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/18500
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
|
|
The file is used for fam15.
Change-Id: I7cdf238a8f7be4bf79546bcfc3c9d05bd8986e3e
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/18635
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
|
|
Definitions are not part of ACPI S3 feature, nor do
they require any AGESA headers so move them to a
better location.
Change-Id: I9269e9d65463463d9b8280936cf90ef76711ed4f
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/18616
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
|
|
Declaration of main in cpu/amd/car.h conflicts with the
definition of main required for x86/postcar.c in main_decl.h.
Change-Id: I19507b89a1e2ecf88ca574c560d4a9e9a3756f37
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/18615
Tested-by: build bot (Jenkins)
Reviewed-by: Philippe Mathieu-Daudé <philippe.mathieu.daude@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Note that M and M_PRO had same DefaultPlatformMemoryConfiguration
defined, use one for both.
Change-Id: Ia1925957800a7fe6ef511b2d041f7a863c8fc931
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/18606
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Relocate the enabling of the LAPIC out of the southbridge source and
surround it with a check for CONFIG_UDELAY_LAPIC (typical for AMD
systems). The LAPIC is now enabled for all cores; not only the BSP,
and not only when the UART is used.
This solves the problem of APs not having their APICs enabled when
the timer is expected to be functional, e.g. verstage often uses
do_printk_va_list() instead of do_printk() which exits early for
APs when CONFIG_SQUELCH_EARLY_SMP=y.
The changes were tested with two Gardenia builds, one using verstage
and another with CONFIG_SQUELCH_EARLY_SMP=n.
Original-Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Original-Reviewed-by: Marc Jones <marcj303@gmail.com>
(cherry picked from commit 93ffc311165f19d4192a5489051fa4264cd8e0ad)
Change-Id: Ieaecc0bf921ee0d2691a8082f2431ea4d0c33749
Signed-off-by: Marc Jones <marcj303@gmail.com>
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/18436
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Only declare S3 support in ACPI if CONFIG_HAVE_ACPI_RESUME
is set.
Change-Id: I6f8f62a92478f3db5de6feaa9822baad3f8e147e
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/18493
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Add some generic functions that can configure the SPI interface to
have faster performance.
Given that the hudson files are used across many generations of FCHs,
make sure to refer to the appropriate BKDG or RRG before using the
functions. Notable differences:
* Hudson 1 defines read mode in CNTRL0 differently than later gens
* Hudson 1 supports setting NormSpeed in Cntr1 but Hudson3 allows
setting FastSpeed as well
* Kabini, Mullins, Carrizo and Stoney Ridge contain a "new" SPI100
controller
Original-Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Original-Reviewed-by: Marc Jones <marcj303@gmail.com>
(cherry picked from commit 1922d6f424dcf1f42e2f21fb7c6d53d7bcc247d0)
Change-Id: Id12440e67bc575dbe4b980ef1da931d7bfae188d
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/18442
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Add defines that will be used later for setting the fastest settings
in the SPI controller.
Original-Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Original-Reviewed-by: Marc Jones <marcj303@gmail.com>
(cherry picked from commit 0d2c28b8156dcc1f3dc925b3c3ba15b6b07f202c)
Change-Id: I660cc9ed6910c33042321c80453c7f74912455d9
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/18441
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Remove unused definitions from a .c file and use the BIT(n) macro
found in types.h instead. Convert existing definitions to BIT(n).
Orignial-Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Original-Reviewed-by: Marc Jones <marcj303@gmail.com>
(cherry picked from commit f403d12b49985ee9d9b339a6659b60ef1560519c)
Change-Id: I24105bf75263236dbdbc2666f03033069d1d36d2
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/18440
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
Fix the error detected by checkpatch and update the copyright date.
TEST=Build and run on Galileo Gen2
Change-Id: Idc55169913e7b7b0aca684c26f6ed3b349fc6c09
Signed-off-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-on: https://review.coreboot.org/18592
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Fix the errors detected by checkpatch and update the copyright dates.
TEST=Build and run on Galileo Gen2
Change-Id: Idad062eaeca20519394c2cd24d803c546d8e0ae0
Signed-off-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-on: https://review.coreboot.org/18591
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Gru/Kevin use 933 MHz (actually 928 MHz for better jitter) as max sdram
frequency, while bob uses 800 MHz.
It's normal some variants can't meet 928 MHz SI requirement and hence
have to use a lower freq as spec.
BUG=chrome-os-partner:61001
BRANCH=gru
TEST=check dpll is 800 MHz on bob
Change-Id: I6d19a351f25d1f48547715ce57c3a87d9505f6f1
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 8176bfea52422c713f144ffec419752aeca66db2
Original-Change-Id: I46afba8d091f1489feeb20cafc44decaa81601fc
Original-Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Original-Signed-off-by: Shunqian Zheng <zhengsq@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/420208
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Original-Commit-Queue: Shasha Zhao <Sarah_Zhao@asus.com>
Original-Tested-by: Shasha Zhao <Sarah_Zhao@asus.com>
Original-(cherry picked from commit eba5dff79eeedae5ff608d2d8d297ccf9c13cb55)
Original-Reviewed-on: https://chromium-review.googlesource.com/448277
Original-Reviewed-by: Derek Basehore <dbasehore@chromium.org>
Reviewed-on: https://review.coreboot.org/18581
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
The K4B4G1646E-BYK0 shares sdram config with K4B4G1646D-BYK0.
For clarity, sdram-ddr3-samsung-2GB now is used by
- K4B4G1646D-BYK0
- K4B4G1646E-BYK0
- K4B4G1646Q-HYK0
BUG=chrome-os-partner:62131
BRANCH=veyron
TEST=emerge
Change-Id: Ie43f23bf8f5f5b1acbb74c85cac17fe181c841c4
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 46d62d87101e0ee1050b00db02b3ecaa4587e9f4
Original-Change-Id: I461c6f36c28ea0eeaf7d64292c9c87ab0c9de443
Original-Signed-off-by: Shunqian Zheng <zhengsq@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/446197
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Original-(cherry picked from commit f98251a4a4fe4d49721a936a684f6ac80f3f6405)
Original-Reviewed-on: https://chromium-review.googlesource.com/446300
Reviewed-on: https://review.coreboot.org/18519
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
This adds SDRAM entries for the following modules:
- Micron: DDMT52L256M64D2PP-107
- Hynix: H9CCNNNBKTALBR-NUD
They are compatible with Samsung K4E8E324EB-EGCF, so this just
copies sdram-lpddr3-samsung-2GB-24EB.inc and changes the name used
in the comment near the top.
Notes on our "special snowflake" boards:
- veyron_danger's RAM ID is hard-coded to zero, so I skipped changes
involving the binary first numbering scheme.
- Rialto's SDRAM mapping is different, so I padded its SDRAM entries
to 24 to match other boards.
- veyron_mickey requires different MR3 and ODT settings than other
boards due to its unique PCB (chrome-os-partner:43626).
BUG=chrome-os-partner:59997
BRANCH=none
TEST=Booted new modules on Mickey (see BUG)
Change-Id: If2e22c83f4a08743f12bbc49b3fabcbf1d7d07dd
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 35cac483e86e57899dbb0898dad3510f4c2ab2d3
Original-Change-Id: I22386a25b965a4b96194d053b97e3269dbdea8c7
Original-Signed-off-by: David Hendricks <dhendrix@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/412328
Original-Reviewed-by: Stefan Reinauer <reinauer@chromium.org>
Original-Commit-Queue: Jiazi Yang <Tomato_Yang@asus.com>
Original-Tested-by: Jiazi Yang <Tomato_Yang@asus.com>
Original-(cherry picked from commit bd5aa1a5488b99f2edc3e79951064a1f824062f6)
Original-Reviewed-on: https://chromium-review.googlesource.com/446299
Original-Commit-Ready: Shunqian Zheng <zhengsq@rock-chips.com>
Original-Tested-by: Shunqian Zheng <zhengsq@rock-chips.com>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/18518
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Fix the following issues:
* A raw read is described by a single read segment, don't assert.
* Support reads longer than the FIFO size.
* Support writes longer than the FIFO size.
* Use the 400 KHz clock by default.
* Remove the error displays since vboot device polling generates
errors.
TEST=Build and run on Galileo Gen2
Change-Id: I421ebb23989aa283b5182dcae4f8099c9ec16eee
Signed-off-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-on: https://review.coreboot.org/18029
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Configure the right GPIOs for finger print sensor interrupt and reset
lines.
As per the schematics GPP_C8 is for sensor interrupt and GPP_C9
is for sensor reset.
Change-Id: Ib25c68ec2fe20b1302b6170d67ceab7e8cca1a83
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/18389
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
One very long line has to be wrapped to be shorter than 80 characters to
satisfy the lint scripts.
Note, that this gets rid of the brackets ().
Change-Id: Ie98eff360ebc5b68ce496edc15eb2d9fddcac868
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-on: https://review.coreboot.org/18556
Tested-by: build bot (Jenkins)
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Philippe Mathieu-Daudé <philippe.mathieu.daude@gmail.com>
|
|
This was removed from the previous version, but we'd like it in
a separate patch, so it's obvious and can easily be applied to the
next version.
Change-Id: I9396009e82e762aa0cc037dbe9e7133962af6354
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/18577
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
This is version 03aed21 from linux/scripts, updated on Dec 12, 2016.
The version needs to be updated because Perl version 5.20 deprecated the
/C regex expression. Perl version 5.24 removed it completely, so the
old version fails to run on the coreboot builders.
Change-Id: Ib97997237ca64c65d7f91d568ae4bec000804331
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/18571
Tested-by: build bot (Jenkins)
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Status:
- The primary PCIe 16x slot works:
It was tested with a GPU compatible with nouveau
- USB and audio are not very reliable
- The ethernet card is not seen with lspci
- The secondary pcie16x slot isn't working:
When plugging a GPU inside, it's not seen with lspci
- SATA works: The board fully boots GNU/Linux
- Serial doesn't work
- Populating the RAM slots might have to follow
the recommended memory configuration that is described
in the mainboard manual in order to be able to boot.
Note that when running the shutdown command, the default
boot firmware will rewrite part of the boot flash before
powering off the machine.
Flashing coreboot internally from the default boot fimrware can
still work, if the power plug is removed after running flashrom.
Change-Id: I934de521d0acceb7770f23b2ae15c31a67ae73eb
Signed-off-by: Denis 'GNUtoo' Carikli <GNUtoo@no-log.org>
Reviewed-on: https://review.coreboot.org/16931
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
These definitions do not require AGESA.h include,
and we will eventually remove agesawrapper.h files.
Change-Id: I1b5b78409828aaf2616e177bb54a054960c3869f
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/18588
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
The size of the array did not match that of the actual
allocation. Furthermore, the tables are written as
part of set_pci_irqs() in hudson/pci.c.
Also the removed code was never reached runtime, as it is
only executed on ACPI S3 resume path that is currently
disabled.
Change-Id: If1c47d53a7656bdff40d93fc132c8c057184ae46
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/18587
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Change-Id: I7a1574259f73a52b66d03c686ae8ab70345c36ed
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/18586
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
This file is only static defines.
Change-Id: Id50a0eba1ce240df36da9bd6b2f39a263fa613df
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/18585
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
|
|
Change-Id: Ib37989ee7535e59b1903537995f8383d8b04387c
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/18584
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Messages from AGESA proper are additionally controlled
by various IDS parameters in board/OptionsIds.h file.
Change-Id: I83e975d37ad2bdecb09c483ecae71c0ed6877731
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/18545
Tested-by: build bot (Jenkins)
Reviewed-by: Philippe Mathieu-Daudé <philippe.mathieu.daude@gmail.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Definition is required to enable use of printk() from AGESA proper.
Change-Id: I6666a003c91794490f670802d496321ffb965cd3
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/18544
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
The current elog implementation has two event types defined for 0xa7,
apparently the result of divergent coreboot trees on chromium where
some events were added to ARM systems but not upstreamed until later.
Fix this by moving ELOG_TYPE_THERM_TRIP to be 0xab, since the current
elog parsing code in chromium is using ELOG_TYPE_SLEEP for 0xa7.
BUG=b:35977516
TEST=check for proper "CPU Thermal Trip" event when investigating a
device that is unexpectedly powering down.
Change-Id: Idfa9b2322527803097f4f19f7930ccbdf2eccf35
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/18579
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Use header (soc/intel/common/block/include/intelblocks/msr.h) for
MSR macros
Change-Id: I401b92cda54b6140f2fe23a6447dad89879a5ef0
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/18554
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Change-Id: I7bd83d293fcc1848f6f64526d8f38d010c1f69a3
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/18223
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Move all common MSRs as per IA SDM into a common location
to avoid duplication.
Change-Id: I06d609e722f4285c39ae4fd4ca6e1c562dd6f901
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/18509
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Create sample model for common Intel XHCI driver.
Change-Id: I81f57bc713900c96d998bae924fc4d38a9024fe3
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/18221
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Select all Kconfig belongs into Intel SoC Family block/ips common
code model and include required header.h file.
Change-Id: Idbce59a57533dbeb9ccfadca966c3d7560537fa0
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/18377
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Don't need "skylake/include/soc/xhci.h", hence removed.
Change-Id: I35df2003f311b557b622ce1d7a1c2e832693c2fc
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/18508
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Split out dual-port switching functionality into dedicated xdci.c.
Change-Id: Ia58fc3fb6d017dd0c19cc450d1caba307fc89a7b
Signed-off-by: Andrey Petrov <andrey.petrov@intel.com>
Reviewed-on: https://review.coreboot.org/18226
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Currently, when using `iasl` 20140926-32 [Oct 1 2014] from Debian 8
(Jessie/stable), the build of the Lenovo X60 fails due to syntax errors.
ASL 2.0 supports `<<`. For consistency, right now, coreboot still uses
the old syntax. So use `ShiftLeft` instead, which also fixes the build
issue with older ASL compilers.
Change-Id: Id7e309c31612387da3920cf7d846b358ac2bdc71
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: https://review.coreboot.org/18520
Tested-by: build bot (Jenkins)
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
All files:
- Previously, various things were hardcoded into the docker containers
that made it necessary to update the Dockerfile files for each new
version of the sdk. Turn those into 'Variables" that are updated during
the build step. Because the makefile is piping the dockerfile through
the sed command and back into the docker build command, the normal
docker "COPY" keyword doesn't work.
coreboot-jenkins-node changes:
- Run ssh-keygen -A to explicitly generate the ssh keys. This fixes an
error: Could not load host key: /etc/ssh/ssh_host_dsa_key
coreboot-sdk changes:
- Remove apt-get upgrade command - The Dockerfile guide recommends
not to run this.
- Change libssl-dev to libssl1.0-dev. libssl-dev's header files won't
build the Chrome-EC codebase.
- Add libisl-dev, needed to build the riscv toolchain.
- Build the toolchain using the -b option
- Add environment variables containing the version and commit that the
coreboot-sdk was built from.
Makefile:
- Update targets to use the version and commit variables
Change-Id: I2c1376fe4b791da2a62fca11bc92c4774cbef1c8
Signed-off-by: Martin Roth <gaumless@gmail.com>
Reviewed-on: https://review.coreboot.org/18001
Tested-by: build bot (Jenkins)
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
|
|
- GCC gets updated from 5.2.0 to 6.3.0:
gcc-6.3.0_riscv.patch is a diff between 5fcb8c4 and 173684b in
riscv-gcc, and it needs gcc-6.3.0_memmodel.patch.
- Binutils goes from 2.26.1 to 2.28:
There is a build error for MIPS gold so I add patch for it.
- GMP gets a bump from 6.1.0 to 6.1.2
- MPFR is updated from 3.1.4 to 3.1.5
- GDB is upgraded from 6.1.1 to 6.1.2
- IASL is changed from 20160831 to 20161222
- LLVM is changed from 3.8.0 to 3.9.1
Change-Id: I20fea838d798c430d8c4d2cc6b07614d967c60c5
Signed-off-by: Iru Cai <mytbk920423@gmail.com>
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/17189
Tested-by: build bot (Jenkins)
|
|
Support for voltage margining is dependent on the platform.
Enabling voltage margining puts additional constraints for
the SLP_S0# to be asserted and hence moving to S0ix state.
If the platform PMIC/VR supports PCH voltage reduction,
voltage marigining can be enabled.
Use the UPD provided by FSP to enable/disable voltage margining.
Change-Id: Iea214e9d7d6126e8367426485c6446ced63caa66
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/18469
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This is selected by default and not overwritten anywhere else for this
board.
Change-Id: I0f803e130366ee322163f7bb6fa16cac75f5416e
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/18541
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins)
|
|
BUG=chrome-os-partner:62963
BRANCH=None
TEST=Compiles successfully
Change-Id: Icb929262fd67362b8e5c5cf31dce04ab1f496695
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/18467
Tested-by: build bot (Jenkins)
Reviewed-by: Rajat Jain <rajatja@google.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
As we drive both channels with the same speed,
chan0dll and chan1dll are the same.
Change-Id: I7253ea9ea66396c536c82d63c67fecb041681707
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/18472
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins)
|
|
AGESA AmdInitEarly() reconfigures the lapic timer in a way that
conflicts with lapic/apic_timer.
This results in an endless loop when printk() is called after
AmdInitEarly() and before the apic_timer is initialized.
This patch forces a reconfiguration of the timer after
AmdInitEarly() is called.
Codepath of the endless loop:
printk()->
(...)->
uart_tx_byte->
uart8250_mem_tx_byte->
udelay()->
start = lapic_read(LAPIC_TMCCT);
do {
value = lapic_read(LAPIC_TMCCT);
} while ((start - value) < ticks);
[lapic_read returns the same value after AmdInitEarly()]
Change-Id: I1a08789c89401b2bf6d11846ad7c376bfc68801b
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Reviewed-on: https://review.coreboot.org/17924
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Relevant changes (commit 250b2ec):
* Fix a bug for ME6 Ignition images.
* Fix signature checking for ME11 and later.
* Add command line arguments.
* Add an option to relocate the FTPR partition to the top of the
ME region, recovering most of the ME region space.
* Print the image minimum size.
* Add write boundary checks, to prevent writes on other regions
in case of bugs.
The new changes have been tested on multiple platforms by the
me_cleaner users. They have been tested also on the author's
X220T with coreboot, where the ME region has been shrinked up to
84 kB without any issue.
Change-Id: I3bd6b4cba9f5eebc3cd4892dd9f188744a06c42b
Signed-off-by: Nicola Corna <nicola@corna.info>
Reviewed-on: https://review.coreboot.org/18473
Tested-by: build bot (Jenkins)
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
|
|
Change-Id: Ia95f6beb1546efdb75a49bccfe293822f0785d7a
Signed-off-by: Nicola Corna <nicola@corna.info>
Reviewed-on: https://review.coreboot.org/18474
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Tested-by: build bot (Jenkins)
|
|
Change-Id: I610797d5002b229211e320a814ce14131cc1dfe7
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/18517
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Alexander Couzens <lynxis@fe80.eu>
|
|
Change-Id: I7de37a026a0899c2d07ea17c9377c8d2283450ab
Signed-off-by: Iru Cai <mytbk920423@gmail.com>
Reviewed-on: https://review.coreboot.org/18481
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
This reverts commit fec8872c9dee4411ba1a89fc8ec833a700b476c6.
The commit introduced a regression which is causing MC4 failures
when 8 RDIMMs are populated in a configuration with a single CPU
package. Using just 4 RDIMMs, the failure does not occur.
After reverting the commit, I tested configurations with
1 CPU (8x8=64GB) and 2 CPU packages (16x8=128GB) using an
Opteron 6276. The MC4 failures did not occur anymore.
Change-Id: Ic6c9de84c38f772919597950ba540a3b5de68a65
Signed-off-by: Daniel Kulesz <daniel.ina1@googlemail.com>
Reviewed-on: https://review.coreboot.org/18369
Tested-by: build bot (Jenkins)
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Reviewed-by: Timothy Pearson <tpearson@raptorengineering.com>
|
|
The newly assigned ACPI ID for coreboot is 'BOOT'
http://www.uefi.org/acpi_id_list
Use this new range of ACPI IDs of "BOOTxxxx" for coreboot specific
ACPI objects instead of the placeholder range of "GOOGCBxx".
Change-Id: I10b30b5a35be055c220c85b14a06b88939739a31
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/18521
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Fix a typo that was introduce in commit 696ebc2d (Broadwell/Sata:
Add support for setting IOBP registers for Ports 2 and 3.) [1].
Setting one of the SATA port 3 IOBP setting was using the value from
the port 2 register.
On the purism/librem13 (on which SATA port 3 is tested), this change
doesn't seem to affect anything, as that typo wasn't exhibiting any
visible problems anyways.
[1] https://review.coreboot.org/18408
Change-Id: I3948def5c0588791009c4b24cbc061552d9d1d48
Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm>
Reviewed-on: https://review.coreboot.org/18514
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Philippe Mathieu-Daudé <philippe.mathieu.daude@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Follow commit 7676730 (mb/lenovo/x60: Remove PCI reset code from
romstage). The PCI reset was copied from code specific for Roda
RK886EX and Kontron 986LCD-M. It is not needed on the MacBook.
Change-Id: I22dac962e8079732591f9bc134c1433f5c29ff4e
Signed-off-by: Axel Holewa <mono-for-coreboot@donderklumpen.de>
Reviewed-on: https://review.coreboot.org/18502
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Change-Id: I304467353bb9989f0d7e0ad7d1b632081f66b1af
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/18482
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
|
|
struct dimm_info has all the parameter types defined in stdint.h
file. So including it.
BUG=none
BRANCH=none
TEST=Build and boot KBLRVP
Change-Id: I707523749ecf415e993b460f9613eae7be859c34
Signed-off-by: Barnali Sarkar <barnali.sarkar@intel.com>
Reviewed-on: https://review.coreboot.org/18471
Tested-by: build bot (Jenkins)
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Save SMBIOS memory information from FSP MEM_INFO_DATA_HOB in CBMEM.
Add function dimm_info_fill() which populates SMBIOS memory
information from FSP MEM_INFO_DATA_HOB data.
BUG=chrome-os-partner:61729
BRANCH=none
TEST=Build and boot KBLRVP to verify the type 17 DIMM info coming in
SMBIOS table from Kernel command "dmidecode".
Change-Id: I0fd7c9887076d3fdd320fcbdcc873cb1965b950c
Signed-off-by: Barnali Sarkar <barnali.sarkar@intel.com>
Reviewed-on: https://review.coreboot.org/18418
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Add the MemInfoHob.h provided by FSP v1.6.0 for aid in parsing the
MEM_INFO_DATA_HOB.
BUG=chrome-os-partner:61729
BRANCH=none
TEST=Build and boot KBLRVP
Change-Id: Ia2b528ba4d9f093006cc12ee317d02e7f3e83166
Signed-off-by: Barnali Sarkar <barnali.sarkar@intel.com>
Reviewed-on: https://review.coreboot.org/18326
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
thinkpad_acpi expects a SSMS method to turn on/off the mute LED
and a MMTS method to turn on/off the microphone mute LED. With
these methods implemented the driver can correctly sync the LEDs
with the corresponding statuses.
There seems to be two different bits to mute the audio in the
Lenovo H8 EC:
* AMUT, used internally (for example to disable the audio before
entering S3).
* ALMT, controllable by the OS, which also toggles the mute LED
(if present).
Tested on a X220T and on a X201.
Change-Id: I578f95f9619a53fd35f8a8bfe5564aeb6c789212
Signed-off-by: Nicola Corna <nicola@corna.info>
Reviewed-on: https://review.coreboot.org/18329
Reviewed-by: Alexander Couzens <lynxis@fe80.eu>
Tested-by: build bot (Jenkins)
|
|
Currently, the USB ports are still powered during S3, so turning
them off may reduce the power consumption.
Note that, when the USB Always on feature is enabled, the USB
ports are always powered, regardless of the USBP state.
This patch also disables the audio, as it might consume some
power or generate some noise.
Both the USB power and the audio are reenabled by coreboot during
the poweron.
Change-Id: If0431b1315fffef2e372e7023f830a66bb7fddae
Signed-off-by: Nicola Corna <nicola@corna.info>
Reviewed-on: https://review.coreboot.org/18464
Tested-by: build bot (Jenkins)
Reviewed-by: Alexander Couzens <lynxis@fe80.eu>
|
|
On the models that support it (like the X220) the LED pulses, on
the others (like the X201) the LED powers off.
Change-Id: I2ac7dbc30609179e4ca5fc0a7b06763431fe3344
Signed-off-by: Nicola Corna <nicola@corna.info>
Reviewed-on: https://review.coreboot.org/18325
Tested-by: build bot (Jenkins)
Reviewed-by: Alexander Couzens <lynxis@fe80.eu>
|
|
thinkpad_acpi expects a MHKG method which returns the current
state of the tablet mode switch shifted left by 3. If such
method is not found, subsequent laptop/tablet mode events are
ignored.
Tested on a X220T.
Change-Id: Ic9ffea2ffe507b3692d1dd7411c52b813ec32146
Signed-off-by: Nicola Corna <nicola@corna.info>
Reviewed-on: https://review.coreboot.org/18328
Tested-by: build bot (Jenkins)
Reviewed-by: Alexander Couzens <lynxis@fe80.eu>
|
|
This timeout is probably needed on all devices with Lenovo H8 embedded
controllers so set the default there.
Change-Id: I830ab1894f7c0f10f55c82e398becf44d810852d
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/18274
Tested-by: build bot (Jenkins)
Reviewed-by: Alexander Couzens <lynxis@fe80.eu>
|
|
Since version 9332965 "serialio: Support for mmap serial ports", SeaBIOS
supports memory mapped serial ports. This patch automatically configures
SeaBIOS when the Hudson UART is enabled.
Change-Id: I072f6a957df7e143d790783546b0725bcd597d9c
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Reviewed-on: https://review.coreboot.org/18025
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
The cr50 part on reef is connected to the SoC's UART lines. However,
when the tx signal is low it causes an interrupt to fire on cr50.
Therefore, keep the tx signal high in suspend state so that it doesn't
cause an interrupt storm on cr50 which prevents cr50 from sleeping.
BUG=chrome-os-partner:63283
BRANCH=reef
TEST=s0ix no longer causes interrupt storm on cr50. Power consumption
normal.
Change-Id: Idaeb8e4427c1cec651122de76a43daa15dc54d0f
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/18491
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Apply tuning for the PCH I2C buses on Eve based on rise/fall time
measurements that were done with a scope.
BUG=chrome-os-partner:59686
BRANCH=none
TEST=Manual testing on Eve P1 to verify that all devices on I2C
buses are still functional. Post-tuning measurement will be done
once a new firmware is released.
Change-Id: I3d70ff455a20ecda374d7e7fa6cd3ab15e7f2621
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/18487
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This patch tries to clean the code by:
o removing duplication of LPC GPIO pads
o removing incorrect definitions from devicetree
o removing irrelevant entries from FMD file
Also adds vital defaults in Kconfig so it is possible to build an image.
Change-Id: Id9913f3b053189166392271152ce5300d82a7de8
Signed-off-by: Andrey Petrov <andrey.petrov@intel.com>
Reviewed-on: https://review.coreboot.org/18479
Tested-by: build bot (Jenkins)
|
|
This fixes a warning that the new toolchain generates.
Change-Id: Idf46026729a474323e74a5cf7a156bf5bc8cf026
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/18485
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
BUG=chrome-os-partner:62967
BRANCH=None
TEST=Verified that touchscreen works on power-on and after
suspend-resume as well.
Change-Id: Id674cbcc2d524a6ed2883bf9f0e9e076890f9a85
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/18466
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Change-Id: Ie0d35c693ed5cc3e890279eda289bd6d4416d9e6
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/18376
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
This change is based on the following commit:
3aa91dc payloads/seabios: Add "git revision" to the SeaBIOS version menu
Change-Id: I9987e3673e70b5cb20173d1ddff6060f42a5374a
Signed-off-by: Denis 'GNUtoo' Carikli <GNUtoo@no-log.org>
Reviewed-on: https://review.coreboot.org/18352
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
On my Thinkpad with an H8-compatible ENE KB9012 EC (GDHT92WW 1.52), when
the battery is nearly full and we switch from battery to AC by plugging
in the cable, the current rate will not drop to 0 immediately, but the
discharging state is cleared immediately.
This leads to the code trying to process an invalid rate value >0x8000,
leading to a displayed rate of >1000W.
This patch changes the logic to deal with these corner cases.
Change-Id: Ideb588d00757f259792e5ae97729e371b63a096c
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Reviewed-on: https://review.coreboot.org/18349
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
- Remove warnings about code using deprecated declarations such as:
plat/mediatek/mt8173/bl31_plat_setup.c: In function 'bl31_platform_setup':
plat/mediatek/mt8173/bl31_plat_setup.c:175:2: warning:
'arm_gic_setup' is deprecated [-Wdeprecated-declarations]
include/drivers/arm/arm_gic.h:44:6: note: declared here:
void arm_gic_setup(void) __deprecated;
- Disable pedantic warnings to get rid of these warnings:
In file included from plat/mediatek/mt8173/bl31_plat_setup.c:36:0:
plat/mediatek/mt8173/include/mcucfg.h:134:21: error:
enumerator value for 'MP1_CPUCFG_64BIT' is not an integer constant
expression [-Werror=pedantic]
MP1_CPUCFG_64BIT = 0xf << MP1_CPUCFG_64BIT_SHIFT
Change-Id: Ibf2c4972232b2ad743ba689825cfe8440d63e828
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/17995
Tested-by: build bot (Jenkins)
Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
This fixes warnings that the new toolchain generates.
Change-Id: I83d2c4c4651a89b443121312a5f36adfc1e4bc48
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/18308
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
It's already selected by SOC_UCB_RISCV.
Change-Id: Ic8a14300cdea2a4ab763b2746434891b72843604
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/18390
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Follow up to https://review.coreboot.org/#/c/18460/
Change-Id: Ic3aada2acf3051622698e10d2e764050e16480d5
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Reviewed-on: https://review.coreboot.org/18475
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
According to USB 2.0 Spec Table 7-7, the High-speed squelch
detection threshold Min 100mV and Max 150mV, and we set USB
2.0 PHY0 and PHY1 squelch detection threshold to 150mV by
default, so if the amplitude of differential voltage envelope
is < 150 mV, the USB 2.0 PHYs envelope detector will indicate
it as squelch.
On Kevin board, if we connect usb device with Samsung U2 cable,
we can see that the impedance of U2 cable is too big according
to the eye-diagram test report, and this cause serious signal
attenuation at the end of receiver, the amplitude of differential
voltage falls below 150mV.
This patch aims to reduce the PHY0 and PHY1 otg-ports squelch
detection threshold to 125mV (host-ports still use 150mV by
default), this is helpful to increase USB 2.0 PHY compatibility.
BRANCH=gru
BUG=chrome-os-partner:62320
TEST=Plug Samsung U2 cable + SEC P3 HDD 500GB/Galaxy S3 into
Type-C port, check if the USB device can be detected.
Change-Id: Ia0a2d354781c2ac757938409490f7c4eecdffe61
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 7d74311c25762668386061234df0562f84b7203e
Original-Change-Id: Ib20772f8fc2484d34c69f5938818aaa81ded7ed8
Original-Signed-off-by: William wu <wulf@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/431015
Original-Commit-Ready: Caesar Wang <wxt@rock-chips.com>
Original-Tested-by: Inno Park <ih.yoo.park@samsung.com>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/18462
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins)
|
|
As David commented the "Bob and other follow-ons match Gru, Kevin should
be the special case here", and update the calculations value for gru/bob
board.
From the actual tests, some regulator voltage than the actual set of less
than 20mv on bob board. (e.g: little-cpus and Center-logic) Update the
{min, max} regulator voltage for Bob board. Make sure we get the accurate
voltage.
BUG=chrome-os-partner:61497
BRANCH=none
TEST=boot up Bob, measure the voltage for little cpu and C-logic.
Change-Id: Iad881b41d67708776bfb681487cf8cec8518064e
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 25e133815f49018e7496c75077b8559c207350a4
Original-Change-Id: I3098c742c7ec355c88f45bd1d93f878a7976a6b4
Original-Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Original-Signed-off-by: Shasha Zhao <Sarah_Zhao@asus.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/424523
Original-Reviewed-by: David Schneider <dnschneid@chromium.org>
Original-Reviewed-by: Brian Norris <briannorris@chromium.org>
Original-Signed-off-by: Shasha Zhao <Sarah_Zhao@asus.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/430403
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/18460
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
This patch adds the DPTF settings specfic to the mainboard and enables
the CPU and other thermal sensors as participant device for poppy.
It enables the DPTF flag in the device tree for poppy. It also includes
the DPTF specific ASL file in the main DSDT definition.
BUG=None
BRANCH=None
TEST=Built for poppy.
Change-Id: If44b01dd3c17fea06681ccf50e8e9f406e642e36
Signed-off-by: Naresh G Solanki <naresh.solanki@intel.com>
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/17926
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Once the PCI command register is written the bridge forwards
future IO and memory regions, as programmed in the respective base
and limit registers, to the secondary PCI bus.
It was previously argumented this is copy-paste and never known
to be required for these more recent platforms:
https://review.coreboot.org/#/c/2706/
Change-Id: Ic8911500a30bc83587af8d4b393b66783fa52e18
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/18330
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
minnow3 doesn't build right now due to API divergence on master branch.
Follow up with recent changes.
Change-Id: Iee84750292f22aa040127bcbfe523a0b9eaa8176
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Reviewed-on: https://review.coreboot.org/18476
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins)
|
|
Update GPIO controls and mainboard configurations for Rowan.
[pg: use the opportunity to clean-up the gerrit-rebase task list with
the entirely unrelated Ignore-CL-Reviewed-on lines]
BUG=chrome-os-partner:62672
BRANCH=none
TEST=emerge-rowan coreboot
Change-Id: I110fb368b3d9fa9dfb2bf091342dfb511ff7c09c
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: f4252cbe94a7456108aaa522e170bca5dcb1fdd1
Original-Change-Id: I18ebc3ccf4c7d051839d7c50e9b0682ef8f09830
Original-Signed-off-by: Yidi Lin <yidi.lin@mediatek.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/430557
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/341513
Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/327003
Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/355221
Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/354670
Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/361360
Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/361361
Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/361362
Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/361363
Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/382320
Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/405110
Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/405130
Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/419795
Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/424139
Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/430293
Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/430294
Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/430295
Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/427820
Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/427821
Ignore-CL-Reviewed-on: https://chromium-review.googlesource.com/427822
Reviewed-on: https://review.coreboot.org/18463
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
The children of Gru should share the benefits. In the real world, Bob can't
pass the eye diagram tests.
BUG=chrome-os-partner:62714
BRANCH=firmware-gru-8785.B
TEST=build coreboot
Change-Id: I2470bbc81acdaf2458d660dca5dc307cc3038f83
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: d0cb3e718a7571f602a00c08a42019851634e7fd
Original-Change-Id: I0ccb48bb52eb770ccc9c8c265b07df46b0308dd3
Original-Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/440745
Original-Reviewed-by: Douglas Anderson <dianders@chromium.org>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/441468
Reviewed-on: https://review.coreboot.org/18461
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Camera and Imaging device should be enabled for camera usecase,
FSP provides a UPD to enable/disable the SA IMGU (Imaging Unit)
expose the same as a config option in devicetree.cb
Also remove a redundant assignment for PchCio2Enable.
BUG=None
BRANCH=None
TEST=lspci should list 00:05:00
Change-Id: I4cf7daf41bfaf4dcba414921cac2e7e12bf89f37
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/18365
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
This enables some required Kconfig options when CONFIG_CHROMEOS is set.
Change-Id: I290902746c1ea19c8bcb69540e34fde09abb9adf
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-on: https://review.coreboot.org/18448
Tested-by: build bot (Jenkins)
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
This adds an oak libpayload config, that should fit all oak-based
devices such as elm.
Change-Id: Iabb71404ff84029a5976371a353e8c92e781ca1f
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-on: https://review.coreboot.org/18447
Tested-by: build bot (Jenkins)
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
These parameters are probably the result of copying from the Thinkpad
X60 code.
Change-Id: I29763b38618d4b306c37424c5c4b57dfcf69424b
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/18290
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Copy GPIO table implementation from the google/reef board except
with board variant features removed. Also exlcude CrOS GPIO functions.
Remove previous romstage GPIO implementation in brd_gpio.h and romstage.c.
Configure GPIO settings for MinnowBoard 3.
Change-Id: Id2817dcf2f8f196ecd13c810f7f0010a115db566
Signed-off-by: Brenton Dong <brenton.m.dong@intel.com>
Reviewed-on: https://review.coreboot.org/18375
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Set the proper memory configuration for the MinnowBoard 3. The current
values are copied from intel/leafhill. Set the proper values for
MinnowBoard 3.
Change-Id: Ie37842f5ce2cabaa892f42ee945c91fe3ace527a
Signed-off-by: Brenton Dong <brenton.m.dong@intel.com>
Reviewed-on: https://review.coreboot.org/18374
Tested-by: build bot (Jenkins)
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
|
|
This commit adds the initial scaffolding for the MinnowBoard 3
with Apollo Lake silicon.
This mainboard is based on Intel's Leafhill CRB with Apollo Lake
silicon. In a first step, it concerns only a copy of intel/leafhill
directory with name changes. Special adaptations for MinnowBoard 3
mainboard will follow in separate commits.
Change-Id: I7563fe37c89511c7035c5bffc9b034b379cfcaf4
Signed-off-by: Brenton Dong <brenton.m.dong@intel.com>
Reviewed-on: https://review.coreboot.org/18298
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
This file reportedly didn't compile on SUSE Linux with gcc 4.3.4:
[...]
> HOSTCC cbfstool/fsp_relocate.o
> In file included from coreboot/src/commonlib/fsp_relocate.c:18:
> coreboot/src/commonlib/include/commonlib/fsp.h:26: error:
> expected '=', ',', ';', 'asm' or '__attribute__' before
> 'fsp_component_relocate'
[...]
According to POSIX-2008[1], sys/types.h defines ssize_t, so include it.
This should not break coreboot code (as opposed to utils code), as we
have a sys/types.h in src/include.
[1]: http://pubs.opengroup.org/onlinepubs/9699919799/basedefs/sys_types.h.html
Change-Id: Id3694dc76c41d800ba09183e4b039b0719ac3d93
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/18417
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Fix up the whitespace issues introduced in commit 39bfc6cb
(nb/i945/raminit.c: Fix dll timings on 945GC).
Change-Id: I3a4152866226401bc51c7fb1752aab541a4c72b0
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: https://review.coreboot.org/18465
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
|
