| Age | Commit message (Collapse) | Author |
|---|
|
Add configuration for all the PCIe Root ports and Clock Source.
Configure the Root Ports as disabled and clock sources as not used.
BUG=None
TEST=Build the mainboard.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: I0a1ad7e056907e454a93f51c84e1d99f08b7bdef
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39166
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This enables display for use by payload.
TEST=Build and boot the mainboard. Ensure that the screens displayed by
payload are visible.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: I5fcd70623b15ae39954242605e75b2c5ce02ff14
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39347
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
BUG=b:150869661
TEST=Build and boot the mainboard. Trigger apreset from EC console.
Trigger reboot from AP console.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: I0d6dd0b4264c11f7ee0ef436cc819b0bb92974f7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39325
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Leave all the GPIOs in not connected state so that they can be
configured depending on the use-case. This is done to park the GPIOs in
a known safe state. This will also help to ensure that the required
GPIOs are configured when the concerned use-cases are enabled.
Below GPIOs are configured in Native Function 1 and are required for
boot-up.
* VCCIN_AUX_VID0
* VCCIN_AUX_VID1
* AP_SLP_S0_L
* PLT_RST_L
* CPU_C10_GATE_L
* GPDs
BUG=None
TEST=Build and boot the mainboard.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Change-Id: I5293536f66a6b08c9c2d2a6281684755a0c0b1b3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39114
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BUG=b:147500717
TEST=none
Change-Id: I32fa27b399127dbf8608e0556c77431d2dad652d
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39358
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
- declare the FPMCU interrupt to be level-triggered
- change EC_PCH_WAKE_ODL gpio to native function mode
- corrected spelling of a signal name in a comment
BUG=b:144933687, b:148179954
BRANCH=none
TEST=none
Change-Id: I62da900d0b71139e55b52d06ec09ca25106f73cd
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39337
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Change-Id: I553fd3a89299314a855f055014ca7645100e12e7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32076
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
|
|
This mainboard has the FSB BSEL straps wired to SuperIO GPIOs. They are
set up in romstage, so it makes no sense to clobber the registers with
garbage in ramstage.
Tested, my Asus P5G41T-M LX still boots and it does not need a full
reset on almost every reboot.
Change-Id: I6ea498119df44243ec42e3cb5c2903de32a17373
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39384
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Not all GPIO4 pins on the SuperIO are configured as outputs.
Change-Id: Idf6350551a91c4c1a25a83e3fb9b1a6722a81c36
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39386
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
This mainboard has the FSB BSEL straps wired to SuperIO GPIOs. They are
set up in romstage, so it makes no sense to rewrite their values in
ramstage.
Tested, my Asus P5QPL-AM still boots.
Change-Id: Ic47f96d12420ebcc70ab5cea940c4c09620c03ca
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39385
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
In order to add the smbios_slot_desc for the SMBIOS Type9 entries into
the devicetree, and not use numbers but strings like
"SlotTypePciExpressGen3X4", smbios.h needs to be included in the
static.c.
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Change-Id: Id15fe4101d14479b02e536fdf63748a241c02bd3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39351
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
|
|
If reading the data for the asset_tag fails, that buffer should be
freed, not the one for serial_number.
Change-Id: I2ecaf7fd0f23f2fb5a6aa0961c7e17fff04847f4
Signed-off-by: Jacob Garber <jgarber1@ualberta.ca>
Found-by: Coverity CID 1419481, 1419485
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39378
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Changes allow to use the integrated panel logic (power sequen-
cing and backlight control) for more connectors. The Kconfigs
GFX_GMA_PANEL_1_PORT and GFX_GMA_PANEL_2_PORT can now be set
to any port, e.g.
config GFX_GMA_PANEL_1_PORT
default "DP3"
Now that the panel logic is not tied to the `Internal` port
choice anymore, we can properly split it into `LVDS` and `eDP`.
This also adds Comet Lake PCI IDs which should still work the
same as Kaby and Coffee Lake.
Change-Id: I78b1b458ca00714dcbe7753a7beb4fb05d69986b
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38921
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
On Lenovo T500 the RTC readings where wrong, as RTC has
different encodings, depending on the statusB register.
Support BCD vs binary RTC format and AM/PM vs 24h RTC format.
Fixes wrong date and time on Lenovo 500.
Change-Id: Id773c33e228973e190a7e14c3d11979678b1a619
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/18498
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
- Add a common page about Montevina ThinkPads.
- Describe how to disable ME and remove its firmware on these models.
- Describe vendor flash layouts.
Thanks to swiftgeek for his help when writing this, especially the last
paragraph and flash layouts.
Change-Id: I85917821efe63fff4b933b6226e99c17b63eb1b9
Signed-off-by: Evgeny Zinoviev <me@ch1p.io>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38926
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
This makes payloads which are hardcoded to a 80x25 console look much
better, e.g. FILO with its "GRUB" user interface.
Change-Id: I9f4752328d85d148cd40a0c2337c7191e1d6a586
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38538
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Keeping a local copy of the framebuffer info allows us to make changes,
e.g. add offsets. It also avoids trouble with relocation.
Change-Id: I852c4eb229dd0724114acb302ab2ed7164712b64
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38537
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
The SCH5317 can have either 0x85 or 0x8c as device ID. However, the
former results in false positives on any ITE IT85xx series embedded
controller, which has led some people to think that chip was actually in
their laptops. Moreover, there is no register dump for the SCH5317.
Since nobody has touched this in over a decade, avoid further confusion
by dropping the misleading definition.
Change-Id: I4d1d34d1b88b878461499e52f1a916ee1e33210d
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39376
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Add LPDDR4 memory configuration for Tiger Lake UP4 platform which
includes
1. DQ/DQs Mapping
2. Board id Support
3. SPD indexing
BUG=none
BRANCH=none
TEST= Build TGL UP4 successfully
Signed-off-by: Srinidhi N Kaushik <srinidhi.n.kaushik@intel.com>
Change-Id: Ibbd7036919c1a91ef12049d2af657f0a3597b57e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39365
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add initial TGL UP4 RVP build enviorment
BUG=none
BRANCH=none
TEST= Build TGL UP4 successfully
Signed-off-by: Wonkyu Kim <wonkyu.kim@intel.com>
Change-Id: Iab7ada0746394539586e7cc159112dc8208fdd7c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39363
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Update FSPS header to include HybridStorageMode Upd for Tiger Lake platform
version 2457.
Signed-off-by: Srinidhi N Kaushik <srinidhi.n.kaushik@intel.com>
Change-Id: Ib6ac89163c0f7a11910e56b9804e386f8bcf355d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39364
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
|
|
For some reason, this symbol gets redefined, which causes a warning.
Hide the warning by checking whether it is already defined.
Change-Id: I70ffc9a799e0b536d6aba7d00f828bd6d915d94c
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39183
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
This change uses drivers/intel/wifi chip for CNVi device and
adds dynamic SSDT entires for CNVi also export wake gpio for CNVi.
BUG=none
BRANCH=none
TEST=Build and boot volteer
Signed-off-by: Srinidhi N Kaushik <srinidhi.n.kaushik@intel.com>
Change-Id: Ia8baf1c7b770db23f31383bda46ae8d090468560
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39333
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
Correct the missing log. Should be the part number not just part.
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I17ac9c6f9545d84645665d3abe1d1613baef4e14
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39353
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Follow JEDEC 21-C to extend LPDDR4 SPD information.
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I68c9782c543afab4423296fa7ac1c078db5649c3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39352
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Add additional pin mux for I2C3, I2C5 for Camera.
These pin muxes were done in FSPs, these pin muxes are for bypassing
pin muxes in FSPs.
BUG=none
BRANCH=none
TEST=Build with pin mux bypass FSP and boot tigerlake rvp board and check camera
Simple test method to check camera: capture image by below commands from
OS console
>media-ctl -V "\"Intel IPU6 CSI-2 5\":0 [fmt:SGRBG10/3280x2464]"
>media-ctl -V "\"Intel IPU6 CSI-2 5\":1 [fmt:SGRBG10/3280x2464]"
>media-ctl -l "\"ov8856 18-0010\":0 -> \"Intel IPU6 CSI-2 5\":0[1]"
>media-ctl -V "\"Intel IPU6 CSI2 BE\":0 [fmt:SGRBG10/3280x2464]"
>media-ctl -V "\"Intel IPU6 CSI2 BE\":1 [crop:(0,0)/3280x2464]"
>media-ctl -V "\"Intel IPU6 CSI2 BE\":1 [fmt:SGRBG10/3280x2464]"
>media-ctl -l "\"Intel IPU6 CSI-2 5\":1 -> \"Intel IPU6 CSI2 BE\":0[1]"
>media-ctl -l "\"Intel IPU6 CSI2 BE\":1 -> \"Intel IPU6 CSI2 BE capture\":0[1]"
>yavta -u -c5 -n5 -I -s 3280x2464 --file=/tmp/frame-#.bin -f SGRBG10
$(media-ctl -e "Intel IPU6 CSI2 BE capture")
Signed-off-by: Wonkyu Kim <wonkyu.kim@intel.com>
Change-Id: I9ad0e5ed452d2b2e8c674abe2a647a0a9c59188e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39201
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Srinidhi N Kaushik <srinidhi.n.kaushik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
To mitigate against sinkhole in software which is required on
pre-sandybridge hardware, the smm entry point needs to check if the
LAPIC base is between smbase and smbase + smmsize. The size needs to
be available early so add them to the relocatable module parameters.
When the smmstub is used to relocate SMM the default SMM size 0x10000
is provided. On the permanent handler the size provided by
get_smm_info() is used.
Change-Id: I0df6e51bcba284350f1c849ef3d012860757544b
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37288
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Change-Id: I7dd6dd8e8debe1b6419625fca38670be375ef581
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39328
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Change-Id: I4fa89dc1ad4196a61bb0cdfaa0d59dfe4c6fff12
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39231
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: Id90496ba54d861157343302c2600adf3b4ccd811
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39230
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Coverity detects pointer dev as FORWARD_NULL. Add sanity check
for dev to prevent NULL pointer dereference if dev did not point
to the audio device.
BUG=CID 1420208
TEST=Built image successfully.
Change-Id: I2a62da44c7044f9dc281eae0949f7f7b612ab238
Signed-off-by: John Zhao <john.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39261
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
This patch upgrades the kernel space to v1.0 to accommodate EC hash,
which is used for CrOS EC's early firmware selection.
BUG=chromium:1045217
BRANCH=none
TEST=Boot Helios. Verify software sync works.
Cq-Depend: chromium:2041695
Change-Id: I525f1551afd1853cae826e87198057410167b239
Signed-off-by: dnojiri <dnojiri@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39137
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Joel Kitching <kitching@google.com>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Updating from commit id 8b9732f5:
2020-01-28 02:32:08 +0000 - (2lib: Fix struct vb2_hash the way it was
meant to be)
to commit id 5059062d:
2020-03-05 02:40:39 (EFS: Implement EFS2 and NO_BOOT mode)
This brings in 19 new commits.
Change-Id: Ic33500921e2c1a6109c24ad36713b41ab6e43de9
Signed-off-by: dnojiri <dnojiri@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39324
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Joel Kitching <kitching@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable DdiPortBHpd and additional pin muxes for DPs. These pin muxes
were done in FSPs, these pin muxes are for bypassing pin muxes in FSPs.
BUG=none
BRANCH=none
TEST=Build and boot tigerlake rvp board and check FSP log or DP port
pin mux from pinctl driver.
Signed-off-by: Wonkyu Kim <wonkyu.kim@intel.com>
Change-Id: Id44cfba696b1a21296278f4de2ad6de8f6bbd63b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39229
Reviewed-by: Shaunak Saha <shaunak.saha@intel.com>
Reviewed-by: Srinidhi N Kaushik <srinidhi.n.kaushik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add samsung K4UBE3D4AA-MGCR SPD as memory sku id 1.
BUG=b:148182234
BRANCH=none
TEST=none
Change-Id: Ie00c45de4d31856109cda13051a75cfa2c2548f7
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39336
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Change-Id: I708281f7861110e4abc02948c74affad9fa37053
Signed-off-by: Peter Lemenkov <lemenkov@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38732
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Add registers that are relevant for the case intrusion detection
functionality.
Intel documents: 332691-003EN, 335193-006, 341081-001, ...
Change-Id: If12d21e8e6721abb877cbbfbbba8f0127a86d96b
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39263
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Enable TCO SMIs in common code, if selected by Kconfig. This is needed
for the follow-up commits regarding INTRUDER interrupt.
Tested on X11SSM-F.
Change-Id: If63effe74ac59b5d051a6454bc6375bb89605215
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39262
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Allow the user to select if TCO shall issue SMIs or not.
Change-Id: Id22777e9573376e5a079a375400caa687bc41afb
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39326
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
These constants are not used in coreboot. They can still be found in:
depthcharge: src/vboot/util/acpi.h
vboot_reference: host/arch/x86/lib/crossystem_arch.c.
BUG=b:124141368
TEST=make clean && make test-abuild
BRANCH=none
Change-Id: I40ad35235c87662a6bcbe6320974a626c6db059e
Signed-off-by: Joel Kitching <kitching@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39319
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
wpsw_boot is deprecated in favour of wpsw_cur. As such,
coreboot no longer needs to share "write protect" GPIO
with depthcharge.
BUG=b:124141368, chromium:950273
TEST=make clean && make test-abuild
BRANCH=none
Change-Id: I2fcb7f82aa063fd72928171af5cbef0356ba620c
Signed-off-by: Joel Kitching <kitching@google.com>
Cq-Depend: chromium:2088434
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39318
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Took less than 30 minutes, and booted on the first try :)
Working:
- Native raminit, using two 2GB DDR3-1333 DIMMs
- S3 suspend/resume
- USB ports and headers
- EHCI Debug with an FT2232H
- Gigabit Ethernet
- Integrated DVI/VGA outputs (libgfxinit)
- PCIe x16 for a graphics card
- PCIe x1 ports
- PS/2 port with a keyboard
- SATA controller
- Audio outputs, both front and rear
- flashrom, using the internal programmer. Tested with coreboot,
as well as with the vendor firmware. Backup chip is untested.
Untested:
- VGA BIOS for integrated graphics init
- Audio inputs
- Non-Linux OSes
- ACPI thermal zone and OS-independent fan control
Not working:
- Default IFD defines the BIOS region as the entire flash chip.
Using 'flashrom --ifd -i bios' is asking for a failed flash!
Change-Id: I467f586530e4a3b53a24b66565b5dcab5e33cf46
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37483
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
This is an ATX mainboard with a LGA1155 socket and four DDR3 DIMM slots.
Porting was done using autoport and then doing a bunch of manual edits.
Working:
- All four DIMM slots
- Serial port to emit spam
- PS/2 keyboard
- S3 suspend/resume
- Rear USB ports
- Integrated graphics (libgfxinit)
- HDMI and VGA
- All PCIe ports
- Realtek GbE (coreboot must set the MAC address)
- Both PCI ports behind the ASM1083 PCI bridge
- SATA ports
- Native raminit
- Flashing with flashrom
- Rear audio output
- VBT
- SeaBIOS to boot Arch Linux
Untested:
- PS/2 mouse
- The other audio jacks
- EHCI debug
- Front USB headers
- Non-Linux OSes
Change-Id: Ia5d9176b6f435977ecdd4fc82fc4bc0974d8d6a4
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39299
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Report fixed SKUID (255) to support mosys.
BUG=none
BRANCH=none
TEST=boot tigerlake rvp board and check mosys and SKUID from smbios
Signed-off-by: Wonkyu Kim <wonkyu.kim@intel.com>
Change-Id: I7a5beed307fd7880a6af127b2dcd06e93e50547d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39269
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Srinidhi N Kaushik <srinidhi.n.kaushik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Automatically add microcode binaries from intel-microcode 3rdparty
respository for Braswell processors using Makefile.
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Change-Id: Iec57e4d5cd63b9bccc869bf178053f1c99b81b9d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39320
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
|
|
Change-Id: I0a9ec0f9605282cbf4fd0ac05070278a3331b6fa
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39361
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
I received feedback that people were confused by "Error: foo", so
replace it with something more user friendly that serves the same
purpose.
Change-Id: I17b902a62020109e079437c8d9ffd7ea5979a3a1
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39274
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Nobody needs "LPC bridge PCI-LPC bridge".
Change-Id: Iac833d4fa34b00d89bdfc9aeb06a96583840b900
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39298
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
The Broadcom BCM5751 NIC on a PCIe card will make the computer hang if
ASPM gets enabled. Blacklist it.
Change-Id: I2cf8d56e9139928a6acfd1d09e47a96b9554fb06
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39193
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Change-Id: I942457a820a59428f7ae302262c4891a4c5ef1a6
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37520
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add configs to enable CNVi mode and CNViBtCore.
BUG=none
BRANCH=none
TEST=Build and boot tglrvp
Signed-off-by: Srinidhi N Kaushik <srinidhi.n.kaushik@intel.com>
Change-Id: Ic372348a1409b2594a85b71b2fc742be96b84b87
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39317
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: caveh jalali <caveh@chromium.org>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This commit creates a nuwani variant for Grunt. The initial settings
override the baseboard was copied from variant treeya.
BUG=b:144890301
TEST=emerge-grunt coreboot
Signed-off-by: Peichao Wang <peichao.wang@bitland.corp-partner.google.com>
Change-Id: Id3a7fc890340e5a88ebc4b516dc2c0b085654999
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39316
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Mathew King <mathewk@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
OCP platform Tiogapass is a 2-socket server platform, which
is based on a chipset including Intel Skylake-SP processors
and a Lewisburg PCH. Skylake-SP is a processor in Intel Xeon
Scalable Processor family.
Following ACPI tables are added:
DSDT/SSDT, MADT, FACP, FACS, HPET, MCFG, SLIT, SRAT, DMAR
This patchset is tested on a Tiogapass board. It booted with
Linux kernel 4.16.0; lscpu command shows all 72 cpus (2 sockets,
18 cores, 2 thread per core); ssh command shows
networking is up from Mellanox ConnectX-4 PCIe NIC card.
Towards successful gerrit buildbot build, note that:
* microcode is in coreboot intel-microcode submodule repo.
* IFD binary is included in this patch.
* Dummy ME binary is used, as it may take long time for Intel
ME binary to be available in public domain.
* Fake FSP binary is used, as at this moment the SKX-SP
FSP binary is not going to be available in public domain.
Known issues (Not intend to address in this initial support for
Xeon-SP processors):
* c6 state is not supported.
* dsdt table is not fully populated, such as processor/socket
devices, some PCIe devices.
* SMM handlers are not added.
Following are some command execution with CentOS booted from
local SATA disk:
[root@localhost ~]# lscpu
Architecture: x86_64
CPU op-mode(s): 32-bit, 64-bit
Byte Order: Little Endian
CPU(s): 72
On-line CPU(s) list: 0-71
Thread(s) per core: 2
Core(s) per socket: 18
Socket(s): 2
NUMA node(s): 2
Vendor ID: GenuineIntel
CPU family: 6
Model: 85
Model name: Intel(R) Xeon(R) Gold 6139 CPU @ 2.30GHz
Stepping: 4
CPU MHz: 140.415
BogoMIPS: 4626.46
Virtualization: VT-x
L1d cache: 32K
L1i cache: 32K
L2 cache: 1024K
L3 cache: 25344K
NUMA node0 CPU(s): 0-17,36-53
NUMA node1 CPU(s): 18-35,54-71
[root@localhost ~]# ifconfig
eth0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet 172.23.68.190 netmask 255.255.0.0 broadcast 172.23.255.255
inet6 2620:10d:c082:9063:268a:7ff:fe57:5af0 prefixlen 64 //cut
inet6 fe80::268a:7ff:fe57:5af0 prefixlen 64 scopeid 0x20<link>
inet6 2620:10d:c082:9063::5d2 prefixlen 128 scopeid 0x0<global>
ether 24:8a:07:57:5a:f0 txqueuelen 1000 (Ethernet)
RX packets 84249 bytes 6371591 (6.0 MiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 8418 bytes 748781 (731.2 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536
inet 127.0.0.1 netmask 255.0.0.0
inet6 ::1 prefixlen 128 scopeid 0x10<host>
loop txqueuelen 1000 (Local Loopback)
RX packets 613 bytes 63906 (62.4 KiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 613 bytes 63906 (62.4 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
[root@localhost ~]# cbmem
36 entries total:
// Lines were cut to avoid checkpatch.pl warnings
Total Time: 96,243,882,140,175,829
Signed-off-by: Jonathan Zhang <jonzhang@fb.com>
Signed-off-by: Reddy Chagam <anjaneya.chagam@intel.com>
Tested-by: johnny_lin@wiwynn.com
Change-Id: I29868f03037d1887b90dfb19d15aee83c456edce
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38549
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
|
|
This patch adds support for Intel Xeon-SP.
This patch is developed and verified with Skylake Scalable
Processor, which is a processor in Xeon-SP family. The code
is expected to be reusable for future geneations of Xeon-SP
processors, and will be updated with smaller targeted
patches accordingly, to add support for additional Xeon-SP
processors, to add features, and to improve the code base.
The Skylake-SP FSP is based on FSP 2.0. The FSP is a
proof-of-concept build. The binary is not shared in public,
when this patch is upstreamed.
Signed-off-by: Jonathan Zhang <jonzhang@fb.com>
Signed-off-by: Reddy Chagam <anjaneya.chagam@intel.com>
Tested-by: johnny_lin@wiwynn.com
Change-Id: Idc9c3bee17caf8b4841f0bc190cb1aa9d38fc23e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38548
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
|
|
Added definitions in FspmUpd.h.
Added gpio_fsp.h file which has definitions needed by mainboard gpio
header file, to set gpio configuration through FSP-M UPD.
Signed-off-by: Jonathan Zhang <jonzhang@fb.com>
Signed-off-by: Reddy Chagam <anjaneya.chagam@intel.com>
Tested-by: johnny_lin@wiwynn.com
Change-Id: I72727952685b5e453f4cde6c2e7e7fc7114c6884
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39287
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Andrey Petrov <anpetrov@fb.com>
|
|
CB:38541 ("ec/google/chromeec: Add SSDT generator for ChromeOS EC")
added a new device_operations structure for chromeec for handling ACPI
SSDT generation. However, this resulted in the original
device_operations which handled lpc read resources to be skipped. This
change fixes the above regression by combining the device operations
for reading resources and ACPI SSDT generation into a single structure
and retains the old logic for enabling of pnp devices.
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: I3a242f4b15603f957e0e81d121e5766fccf3c28d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39321
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
The register TCO1_STS is never cleared, which will cause SMIs to either
retrigger over and over again (e.g. TIMEOUT) or prevent concurrent
interrupt events, depending on which event triggered.
Clear both TCO2_STS and TCO1_STS.
This also fixes the issue where SECOND_TO_STS will always end up set in
the SMI handler by unconditionally (re)setting it.
Tested on X11SSM-F, where enabling TCO caused the terminal to get
flooded with SMI debug messages. With this patch, a message gets written
every ~1 second.
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: Ia57c203a672fdd0095355a7e2a0e01aaa6657968
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39259
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Andrey Petrov <anpetrov@fb.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Lenovo ThinkPad X230t Convertible Laptop works well with X230 default
image (see CB:34361).
Change-Id: Ib0a73fd551f0d26c789d3fd13541b2d1571742cb
Signed-off-by: Peter Lemenkov <lemenkov@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38482
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
We include it only in one file. So let's simplify everything and do like
autoport does.
Change-Id: I71f092ed7582b4931122d72f41d0b42a7569b96e
Signed-off-by: Peter Lemenkov <lemenkov@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38781
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Add support for Max98373 speaker amp & ALC5682 headset codec
BUG=none
BRANCH=none
TEST=Build and boot tigerlake rvp board
Signed-off-by: Srinidhi N Kaushik <srinidhi.n.kaushik@intel.com>
Change-Id: I013dbc6246b07a501f9bff80c2bca3594e6cc146
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38561
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
|
|
Move channel loop at the top level to deduplicate the logic.
BUG=none
BRANCH=kukui
TEST=Boots correctly on Kukui
Change-Id: Iea623d1bd1f7d736e81f66f191a1bf8476d30404
Signed-off-by: Huayang Duan <huayang.duan@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38490
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
|
|
The TX window will offset to edge during DVFS switch, which may cause
TX data transmission error and random kernel crash. Therefore, use the
standard dqsosc (DQS Oscillator) for TX window tracking.
BUG=b:142358843
BRANCH=kukui
TEST=Boots correctly on Kukui
Change-Id: Idcf9213a488e795df3faf64b03588cfe55cb2f81
Signed-off-by: Huayang Duan <huayang.duan@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37996
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
|
|
Because eMCP and discrete DDR devices have different DVFS tables, their
EMI bandwidth thresholds should also be different. When the EMI total
bandwidth reaches the threshold, the system will notify DVFS module to
perform DVFS switch for system performance in low power states.
This patch increases the threshold from 0xa to 0xd for eMCP DDR devices
so that DVFS switch will be less likely to happen.
The register table of EMI_BWCT0 is incorrect in the datasheet. According
to the hardware design, BW_2ND_INT_BW_THR should be in bits [30:24]
instead of [22:16]. However, the logic in DRAM driver is correct,
aligned with the hardware design, so we don't need to correct it.
BRANCH=kukui
BUG=b:142358843
TEST=bootup pass
Change-Id: I82c3c70bcd90df3fdd613c0353aba0f176bc82bc
Signed-off-by: Huayang Duan <huayang.duan@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39034
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: Ic4db37112e7b2329f9e4885139deca12557ffe3a
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39134
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
There is no need to set the NpkEn option to disable the NPK device,
since it has already been done in the devicetree.
Change-Id: I429f1129dc4149067503cd2ff9fb4c76cdc919f0
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39120
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Allows to override the PortUsb20Enable and PortUsb30Enable FSP options
(which are set to 1 by default) to enable/disable USB ports if the
usb_config_override flag is set to "1". Therefore, these changes will
not affect other boards with an Apollo Lake processor.
Change-Id: Ia94a2be1647f7743ef0c918ae3b34437a179261c
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38815
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Add a new ripto variant based off of the volteer baseboard design.
BUG=b:148385924, b:150810535
TEST="emerge-volteer coreboot chromeos-bootimage", flash ripto image
and verify ripto boots to the kernel.
Change-Id: If7606588147500a465f16c7846e2c8429ece93ec
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39301
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: caveh jalali <caveh@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Srinidhi N Kaushik <srinidhi.n.kaushik@intel.com>
|
|
Declare variant_early_gpio_table() weak to allow override by variants.
BUG=b:148385924, b:150810535
TEST=none
Change-Id: Ife5e3b75256f71ecd763c4000fd2c7d7c927bb64
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39300
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: caveh jalali <caveh@chromium.org>
Reviewed-by: Srinidhi N Kaushik <srinidhi.n.kaushik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable VBOOT support on all devices that have a 12 MiB flash, using
RW_MAIN_A + RW_MAIN_B partition, allowing the use of tianocore payload
in both RW_MAIN_A, RW_MAIN_B and WP_RO.
* Add VBNV section to cmos.layout
* Add FMAP for VBOOT
* Select Kconfigs for VBOOT
* Enable VBOOT_SLOTS_RW_AB by default
The VBNV is intentionally not covered by the CMOS checksum.
Tested on x230 and T440p.
Change-Id: I8a35a06ece1e9d57a2ef23970e61ae26fafce543
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Signed-off-by: Jonas Moehle <ad-min@mailbox.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/32617
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Peter Lemenkov <lemenkov@gmail.com>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
|
|
This is a port of https://review.coreboot.org/c/coreboot/+/22337 to the
Haswell northbridge. This code is necessary to support the dGPU of the
t440p. Code was cut and pasted from Sandy Bridge with vendor IDs updated
to the correct Haswell values. Tested on t440p with dGPU on Ubuntu
18.04.4 with 5.3.0-28 kernel. Without patches dmesg reports Nouveau is
unable to read the VBIOS of the dGPU as it has an invalid checksum (I
checked that the ROM in CBFS is correct). With this patch DRM works
correctly with both the Nouveau driver and the Nvidia proprietary
driver. Windows 10 1909 also tested but generates bluescreen once GPU
driver is loaded.
Change-Id: Ie5f089fb6fd774e6c61f4f9281e2945bd44edf27
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38743
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
Use the ifdtool --output flag to modify coreboot.pre inplace, instead
of using the `mv` command to get the same result. In this way the stdout
will make more sense in the build context.
Change-Id: I6dacc8b39052801c770c02fa2aa1b526747ae496
Signed-off-by: Marcello Sylvester Bauer <sylv@sylv.io>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39275
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Coverity detects pointer dev as FORWARD_NULL. Add sanity check
for dev to prevent NULL pointer dereference.
BUG=CID 1353148
TEST=Built and boot up to kernel.
Change-Id: Ic0ad1ec79c950a3c17feccdde4f87f4a107fe8c0
Signed-off-by: John Zhao <john.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39260
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
This reverts commit 2b9004de602f98a404b17584ab3e1451f165c1f4.
Reason for revert: QEMU emulates that chipset and with that commit a Linux guest kernel can't find IDE devices anymore.
Change-Id: Iad75af4ea9993d6a2ec5433ad30d39900dab874e
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39238
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Keith Hui <buurin@gmail.com>
|
|
This also drops individual copyright notices, all mentioned authors in
that part of the tree are listed in AUTHORS.
Change-Id: Ib5a92bb46ff2b9d2928aae3763daec71747044c2
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39284
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
|
|
This also drops individual copyright notices, all mentioned authors in
that part of the tree are listed in AUTHORS.
Change-Id: I770c1afd9b68a40ec0e69818f24b5ef3ad4f1d35
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39283
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
|
|
While a 4 clause BSD license "with advertising" is incompatible to the
GPL, the University of California declared the problematic clause null
and void.
See ftp://ftp.cs.berkeley.edu/pub/4bsd/README.Impt.License.Change
Change-Id: I4ebb822f64989a5fc8f686e548a94653508d1113
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39282
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
This also drops individual copyright notices, all mentioned authors in
that part of the tree are already listed in AUTHORS.
Change-Id: I19b1c379b474dd011e2d0f8c8202ff1351c9290d
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39281
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
This also drops individual copyright notices, all mentioned authors in
that part of the tree are already listed in AUTHORS.
Change-Id: Ic5eddc961d015328e5a90994b7963e7af83cddd3
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39279
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
This also drops individual copyright notices, all mentioned authors in
that part of the tree are already listed in AUTHORS.
Change-Id: Ic2bab77edaf7ad97b7f3278cb108226a18cf3791
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39278
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
|
|
If the ChromeOS EC uses EC early firmware selection (EFS), the AP vboot
build must also enable EC EFS. Puff EC uses EFS, so enable it in the AP
vboot build.
BUG=b:150742950
TEST=Puff can boot with EC EFS with hardware write protect enabled
BRANCH=none
Signed-off-by: Sam McNally <sammc@chromium.org>
Change-Id: I0877000b7d277106436831f2d69775c25299da9e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39273
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
If the ChromeOS EC uses EC early firmware selection (EFS), the AP vboot
build must also enable EC EFS. Add an option to control this, passing it
through to vboot.
BUG=b:150742950
TEST=none
BRANCH=none
Signed-off-by: Sam McNally <sammc@chromium.org>
Change-Id: I697e90748e19d15af154011413b30c0f2a0bf52e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39272
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
|
|
This reverts commit c8b0f31ca1b6cae993736d47d919080b6c186c6f.
Bumping the FADT table version from 3 to 6 causes
Windows 10 to BSOD with an ACPI BIOS error or simply
fail to boot on multiple platforms (Haswell, Broadwell,
Braswell, Skylake). Revert until the issue can be properly
identified and corrected.
Change-Id: I261d953321df2616a3f1c3460a535b57a8848315
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39307
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Change-Id: Iaa295c74e9c470d5830e22d0b0c73013c7333293
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39266
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Michael Niewöhner
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The cache as ram code will use one form of a non-eviction mode.
Change-Id: I418eb48434aa3da3bf5ca65315bb8c9077523966
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/36239
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Otherwise there will, after make gitconfig,
be (hidden) shell command failures with 'git commit -s':
gmake: util/lint/check-style: Command not found
gmake: *** [Makefile.inc:632: check-style] Error 127
Change-Id: I3891dee53702ee10e5e44dae408193e49d7a89f1
Signed-off-by: Idwer Vollering <vidwer@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38227
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
BSD grep (on macOS) doesn't like repeated repetition operators, it
throws the error
grep: repetition-operator operand invalid
This removes the superfluous repetition operator to make the commit-msg
hook work on macOS and other platforms not using GNU grep.
Change-Id: Id0f57d0f14634f7844b889d71342b2982fcadeb2
Signed-off-by: Patrick Elsen <pelsen@xfbs.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38205
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
The memNTrainFlowControl array is generating Coverity warnings
in multiple places in code where it attempts to write to index 1.
The array is defined as either 2 elements or 1 of NULL depending
on #if (AGESA_ENTRY_INIT_POST == TRUE). This is likely a false
alarm from Coverity (memory should not be training outside of a
POST), but adding a second NULL element for the
AGESA_ENTRY_INIT_POST == FALSE case. Tested on Lenovo G505s.
Change-Id: Iaebe0830471e1854d6191c69cdaa552f900ba7a6
Signed-off-by: Joe Moore <awokd@danwin1210.me>
Found-by: Coverity CID 1357451, 1357452, 1357453
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38176
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Potential for out-of-bounds read. However, this code is not
used on F14, F15tn, or F16kb platforms. As can be seen in
vc/amd/agesa/f15tn/Config/PlatformInstall.h only multiple
socket F10 is supported. Tested on Lenovo G505s.
Change-Id: Ib71fe32d89840b9f25619d74980e562fd626952b
Signed-off-by: Joe Moore <awokd@danwin1210.me>
Found-by: Coverity CID 1241831
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38035
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
AllocParams.Persist is used uninitialized when calling
HeapAllocateBuffer. This could lead to unpredictable or
unintended results. The f15tn and f16 versions of
AmdS3Save.c have already addressed this by initializing
AllocParams.Persist=0 in the same location in the code,
so adding to f14 only.
Change-Id: I2cbfbc4ad14a861e0cd92f130209b3b0f5b76a17
Signed-off-by: Joe Moore <awokd@danwin1210.me>
Found-by: Coverity CID 1241806
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37194
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
|
|
Uninitialized variable will contain an arbitrary value left from
earlier computations. This issue has already been addressed
in the f15tn and f16kb versions of this same file, so am
backporting the fix.
Change-Id: Id876107265689e08ad6760e514a4911f32b53da7
Signed-off-by: Joe Moore <awokd@danwin1210.me>
Found-by: Coverity CID 1241856
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38048
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The generic MemNProgramNbPstateDependentRegistersUnb function is unused,
and generates a Coverity warning of an unused switch case. Only family
specific versions of this function are called elsewhere. Delete unused
function.
Change-Id: I2afc83861f4b3a13bfc1eef4920cd3023e608e94
Signed-off-by: Joe Moore <awokd@danwin1210.me>
Found-by: Coverity CID 1241810
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38493
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Both T530 and W530 share the same PCI device id of 0166 for the iGPU.
Change-Id: Idce809e3820a653144db424aff1c55b70c4c693a
Signed-off-by: Prasun Gera <prasun.gera@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/35431
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Peter Lemenkov <lemenkov@gmail.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Looks like it should select it like any other Lenovo xx20/xx30 boards
around.
UNTESTED.
Change-Id: Iaa4983c0a6365d77ac647f68d112a405d782d501
Signed-off-by: Peter Lemenkov <lemenkov@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38710
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
These two variables are initialized to zero by default.
Change-Id: I590f601b5297a9bfa93607442d7e0b8d79f1ab51
Signed-off-by: Peter Lemenkov <lemenkov@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38709
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Change-Id: I3323e713970041b0665ca17bbcad985cba600687
Signed-off-by: Peter Lemenkov <lemenkov@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38708
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Only whitespace changes, minor comments. This helps making diff between
devicetrees shorter.
Change-Id: Ia1a84728abbece96a3d05b3b1616ac58535845bc
Signed-off-by: Peter Lemenkov <lemenkov@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37601
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Some local functions need renaming to avoid name collision.
Change-Id: I0ca311c12f013e54e23ff0427421bfad0b747ea6
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/37195
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
GNU Make 4.3 doesn't propagate a global .SILENT to sub-processes
anymore. Let's make it explicit to maintain the behaviour we are
used to.
From the changelog:
[SV 54740] Ensure .SILENT settings do not leak into sub-makes
Change-Id: I3de51c245d3344b062dc0fe9c62b8d5c0ac5e67d
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38931
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
It somehow creeps into `make clean`, but is not used at all. Since no
VIA platform remains in coreboot, drop the utility as well.
Change-Id: Ia7e11379a6db650b5190a056226a9101c2be7dec
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38853
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
"amdfam10" is no more.
Change-Id: Ibf4892bb4076eb88b864fc0e894b986bf6f6e5bf
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/38054
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
