| Age | Commit message (Collapse) | Author |
|---|
|
Give it somewhere to put the new info in sysinfo, and tell it how to parse
the new tables which it doesn't yet understand.
Change-Id: I01d3318138696e6407553c27c1814f79e3fbc4f8
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: http://review.coreboot.org/1718
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Read out the post code from the previous boot and
log it if the code is not one of the expected values.
Test:
1) interrupt the boot of the system, this is easiest
with warm reset button when servo is attached
2) check the event log with mosys
65 | 2012-09-09 12:32:11 | Last post code in previous boot | 0x9d
Change-Id: Id418f4c0cf005a3e97b8c63de67cb9a09bc57384
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1744
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
This will use 3 bytes of CMOS to keep track of the POST
code for the current boot while also leaving a record of
the previous boot.
The active bank is switched early in the bootblock.
Test:
1) clear cmos
2) reboot
3) use "mosys nvram dump" to verify that the first byte
contains 0x80 and the second byte contains 0xF8
4) powerd_suspend and then resume
5) use "mosys nvram dump" to verify that the first byte
contains 0x81 and the second byte contains 0xFD
Change-Id: I1ee6bb2dac053018f3042ab5a0b26c435dbfd151
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1743
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
This is a slight improvement over the rep movsb loop
Change-Id: Id71d9bfe5330b154a5c62fac85ce3955ae89b057
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1742
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
The linux kernel relies on the RTC reporting pending interrupts if
the RTC alarm was used to wake the system. If we clear these flags
here then the rtc-cmos driver in the kernel will think that no
interrupts are pending and will not re-start the timerqueue to
handle the alarm timerqueue node.
This flag doesn't exist in SMM but the rtc code is compiled there.
Since rtc_init() is not called by SMM it is guarded with an ifdef.
I performed several thousand suspend/resume cycles without seeing
an issue where hwclock was unable to read from /dev/rtc. There
still is a potential kernel issue where the timerqueue can stall
but this makes that much less likely to happen on resume.
Change-Id: I5a343da4ce5c4c8ec4783b4e503869ccfa5077f0
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1741
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
In case tseg_relocate() is called again on a pointer we should not
relocate it again.
Change-Id: Ida1f9c20dc94b448c773b14d8864afe585369119
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1740
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
We are seeing ME disabled and ME error events on some devices
and this extended info can help with debug.
Also fix a potential issue where if the log does manage to get
completely full it will never try to shrink it because the only
call to shrink the log happens after a successful event write.
Add a check at elog init time to shrink the log size.
Change-Id: Ib81dc231f6a004b341900374e6c07962cc292031
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1739
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
The handling of write enable was not entirely correct,
the opcode needs to be skipped when the controller is
locked down.
Addresses were not getting set properly for erase commands
which seemed to mostly work when the previous command had
set an address.
Tested by adding events to the event log at runtime on a
freslhy flashed device (with locked down SPI controller)
until the log log shrink happens to ensure it does not hang:
hexdump -C elog.event.kernel_clean
00000000 01 00 00 00 ad de 00 00 00 00
for x in $(seq 1 232); do
cat elog.event.kernel_clean > /sys/firmware/gsmi/append_to_eventlog
done
mosys eventlog list | tail -6
154 | 2012-09-01 13:54:43 | Kernel Event | Clean Shutdown
155 | 2012-09-01 13:54:43 | Kernel Event | Clean Shutdown
156 | 2012-09-01 13:54:43 | Kernel Event | Clean Shutdown
157 | 2012-09-01 13:54:43 | Kernel Event | Clean Shutdown
158 | 2012-09-01 13:54:43 | Log area cleared | 1030
159 | 2012-09-01 13:54:43 | Kernel Event | Clean Shutdown
Change-Id: I3a50dae54422a9ff37daefce3632f8bcbe4eb89f
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1717
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
This is a cosmetic change which formats timestamp information
retrieved by cbmem.py.
Instead of printing timestamps in a single line, print them one per
line and add time (in us) elapsed since the previous timestamp.
time base 4149594, total entries 18
1:56,928
2:58,851 (1,923)
3:175,230 (116,378)
4:175,340 (109)
8:177,199 (1,859)
9:214,368 (37,168)
10:214,450 (81)
30:214,462 (11)
40:215,205 (743)
50:217,180 (1,974)
60:217,312 (132)
70:436,984 (219,671)
75:436,993 (8)
80:441,424 (4,431)
90:442,487 (1,062)
99:553,777 (111,289)
1000:556,513 (2,736)
1100:824,621 (268,107)
Change-Id: I0d25cafe766c10377017697e6b206276e1a92992
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: http://review.coreboot.org/1716
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
For some reason which I fail to understand, specifying endiannes using
'@' (which means 'native' and should be the same as '<' on x86
platforms) causes cbmem.py to crash the machine on 64 bit systems.
What happens is that the addresses read from various table headers'
struct representations do not make sense, when bogus address gets
passed to get_phys_mem, the crash happens while that function is
executed.
dlaurie@ found out that replacing "@" with "<" in fact fixes the
issue. After some investigation I am just submitting this fix without
much understanding of the root cause.
Change-Id: Iaba9bc72a3f6b1d0407a5f1e3b459ccf5063969d
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: http://review.coreboot.org/1715
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
When bringing up VGA by running the option rom it's sometimes
useful to get more information about the mode that gets set,
or the reason why the mode could not be set or a picture could
not be displayed. Also prefix the output from VBE mode setting
with VBE:
Copying VGA ROM Image from fff0fd78 to 0xc0000, 0x10000 bytes
Real mode stub @00000600: 867 bytes
Calling Option ROM...
int15_handler: INT15 function 5fac!
... Option ROM returned.
VBE: Getting information about VESA mode 4161
VBE: resolution: 1280x1024@16
VBE: framebuffer: d0000000
VBE: Setting VESA mode 4161
VGA Option ROM has been loaded
Change-Id: I2be11f095dc62ed3c99e0d4272ad9d6521608a44
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1714
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
CBFS allows coreboot rom images that are only partially covered
by the filesystem itself. The intention of this feature was to
allow EC / ME / IMC firmware to be inserted easily at the beginning
of the image. However, this was never implemented in cbfstool.
This patch implements an additional parameter for cbfstool.
If you call cbfstool like this:
cbfstool coreboot.rom create 8192K bootblock.bin 64 0x700000
it will now create an 8M image with CBFS covering the last 1M of
that image.
Test:
cbfstool coreboot.rom create 8192K bootblock.bin 64 0x700000
creates an 8M image that is 7M of 0xff and 1M of CBFS.
Change-Id: I5c016b4bf32433f160b43f4df2dd768276f4c70b
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1708
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Now that we have FMAP support in coreboot use it to find the
offset in flash for ELOG to use.
If coreboot has elog configured with a smaller size then use
that over the FMAP size. This is because I set aside a 16KB
region in the FMAP but we only use 4KB of it to keep the impact
to boot/resume speed to a minimum.
FMAP: Found "FMAP" version 1.0 at ffe10000.
FMAP: base = 0 size = 800000 #areas = 32
FMAP: area RW_ELOG found
FMAP: offset: 3f0000
FMAP: size: 16384 bytes
FMAP: No valid base address, using 0xff800000
ELOG: base=0x003f0000 base_ptr=0xffbf0000
ELOG: MEM @0x00190ad8 FLASH @0xffbf0000
ELOG: areas are 4096 bytes, full threshold 3072, shrink size 1024
Change-Id: I3d826812c0f259d61f41b42797c58dd179f9f1c8
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1706
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
|
|
Now that WREN prefix is handled properly ELOG is able to write
when the SPI controller is locked down.
To test, ensure that runtime SPI write via ELOG is successful by
checking the event log for a kernel shutdown reason code:
5 | 2012-08-27 11:09:48 | Kernel Event | Clean Shutdown
6 | 2012-08-27 11:09:50 | System boot | 26
7 | 2012-08-27 11:09:50 | System Reset
Change-Id: If6d0dced7cb0f5ca7038b3d758f31b856826d30b
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1712
Reviewed-by: Marc Jones <marcj303@gmail.com>
Tested-by: build bot (Jenkins)
|
|
The code that attempts to use the opmenu needs to have a special
case for write enable now that it is handled as an atomic prefix
and not as a standalone opcode.
To test, ensure that runtime SPI write via ELOG is successful by
checking the event log for a kernel shutdown reason code:
5 | 2012-08-27 11:09:48 | Kernel Event | Clean Shutdown
6 | 2012-08-27 11:09:50 | System boot | 26
7 | 2012-08-27 11:09:50 | System Reset
Change-Id: I527638ef3e2a5ab100192c5be6e6b3b40916295a
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1710
Reviewed-by: Marc Jones <marcj303@gmail.com>
Tested-by: build bot (Jenkins)
|
|
Check the RTC on boot after RTC battery failure and ensure
that the reported build date matches what is reported:
> grep ^rtc /proc/driver/rtc
rtc_time : 01:00:21
rtc_date : 2012-08-16
Change-Id: If23f436796754c68ae6244ef7633ff4fa0a93603
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1709
Reviewed-by: Marc Jones <marcj303@gmail.com>
Tested-by: build bot (Jenkins)
|
|
The "debug" macro used internally in the libpayload USB subsystem was very
generically named and would leak into consumers of the library that included
usb.h directly or indirectly. This change turns that #define from a macro into
a static inline function to move away from the preprocessor, and also renames
it to usb_debug so it's less likely to collide with something unrelated.
Change-Id: I18717df111aa9671495f8a2a5bdb2c6311fa7acf
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: http://review.coreboot.org/1738
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Tested-by: build bot (Jenkins)
|
|
While it might be slightly more convenient to not have to call usb_poll
manually after calling usb_initialize, you'll still likely want to call it
before trying to use a USB device since one have have been hotplugged since
you last looked. By not calling usb_poll, usb_initialize completes quickly and
can be called unconditionally without a long delay. The delay can be put off
until later when we're sure it's necessary.
Change-Id: Ib8b1bdea996702c42d1b7021f492d9f8e174d304
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: http://review.coreboot.org/1737
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Tested-by: build bot (Jenkins)
|
|
The usb_initialize function would scan for USB host controllers by brute force
iterating over all possible busses, devices, and functions. This change makes
it recursively scan busses only if it finds them on the other side of a bridge,
and only scan for functions beyond function 0 if the device claims to be
multifunction.
This change also takes the opportunity to clean up some style problems
throughout the file.
Change-Id: I0f5e8b9a454a42a76d30bccca898c8e1af770b2b
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: http://review.coreboot.org/1736
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Tested-by: build bot (Jenkins)
|
|
Change-Id: I02cf353ce7c955cb11ca11c0d5b8aa630cf15fdb
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: http://review.coreboot.org/1735
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
gcc recognizes the format function attribute which tells the compiler to expect
the format string to look a certain way and for its arguments to be of
appropriate types. This helps to prevent errors like the one that was recently
fixed in libpayload's assert.
Change-Id: I284ae8bff32f72cfd2d1a250d126c729b38a5730
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: http://review.coreboot.org/1731
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
The assert macro in libpayload was using a format string which printed the
line number with %s. The line number came from the __LINE__ predefined macro
which resolves to an integer constant.
Change-Id: I0e00d42a1569802137cf440af3061d7f397fdd27
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: http://review.coreboot.org/1730
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Change-Id: I0f3a82de860fd3afa10a557b37fb90fe6b06ae90
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: http://review.coreboot.org/1726
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Tested-by: build bot (Jenkins)
|
|
The implementations for various stdlib functions in libc/memory.c are very
generic and should work under just about any circumstances. They are
unfortunately also very slow. This change makes them weak symbols so that
faster versions can be defined on a per architecture basis which will
automatically take the place of the slow versions.
Change-Id: Ia1ac90d9dcd45962b2a15f61ecc74b0a4676048d
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: http://review.coreboot.org/1725
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Tested-by: build bot (Jenkins)
|
|
This information is now stored in a structure instead of in a few seperate
fields. libpayload hadn't been updated to reflect the new layout or to consume
the new information intelligently.
Change-Id: Ice3486ffcdcdbe1f16f9c84515120c591d8dc882
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: http://review.coreboot.org/1724
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Tested-by: build bot (Jenkins)
|
|
Change-Id: Ifb7c18f9ca566bd50ca138ffd8af951375089537
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: http://review.coreboot.org/1722
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Tested-by: build bot (Jenkins)
|
|
These end up being loaded at 0 otherwise and overwrite some coreboot tables.
Built and booted on Stumpy. Saw that the coreboot tables were no longer
overwritten.
Change-Id: Ia9f521d976d0ad544a8205323ae0ddfa8d253d29
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: http://review.coreboot.org/1721
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
This file uses uint*_t types but hadn't included stdint.h itself.
Change-Id: Ib883f62951bae1ece5134c6bd0f4799a80740e8e
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: http://review.coreboot.org/1720
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Tested-by: build bot (Jenkins)
|
|
cbfstool was not looking at any dependencies when building
by running make in util/cbfstool. By fixing this it's not
required to make clean every time you edit a file in there.
Change-Id: I544fd54d4b9dd3b277996c21ade56dc086b84800
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1707
Reviewed-by: Marc Jones <marcj303@gmail.com>
Tested-by: build bot (Jenkins)
|
|
This appears to fix an infrequent resume hang on Ivybridge.
Tested on 2 devices with 15k suspend/resume cycles each
Change-Id: I53618bc7966824413f1720a2be3cbd2550e29473
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1704
Reviewed-by: Marc Jones <marcj303@gmail.com>
Tested-by: build bot (Jenkins)
|
|
(elog portion, support in EC code pending)
- Use a new EC command to read the last post code
from the previous boot
- If the post code is not well-known final boot
or resume code then log it
Change-Id: Id6249e9a182243eb87c777edd56f48de72125e77
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1703
Reviewed-by: Marc Jones <marcj303@gmail.com>
Tested-by: build bot (Jenkins)
|
|
Until now, the MRC cache position and size was hard coded in Kconfig.
However, on ChromeOS devices, it should be determined by reading the
FMAP.
This patch provides a minimalistic FMAP parser (libflashmap was too
complex and OS centered) to allow reading the in-ROM flash map and
look for sections.
This will also be needed on some partner devices where coreboot will
have to find the VPD in order to set up the device's mac address
correctly.
The MRC cache implementation demonstrates how to use the FMAP parser.
Change-Id: I34964b72587443a6ca4f27407d778af8728565f8
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1701
Reviewed-by: Marc Jones <marcj303@gmail.com>
Tested-by: build bot (Jenkins)
|
|
Otherwise object paths will look like build/cbfs/"fallback"/...
Change-Id: I3e60f90f7490e71b0da075d3ea8fc847abc07938
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1700
Reviewed-by: Marc Jones <marcj303@gmail.com>
Tested-by: build bot (Jenkins)
|
|
This is purely cosmetic. All error messages in the Sandybridge raminit
code printed a newline at the end.
Change-Id: I880d291928291d487039850a2a3d53a1101124ba
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1699
Reviewed-by: Marc Jones <marcj303@gmail.com>
Tested-by: build bot (Jenkins)
|
|
build.h is generated at build time,
with highly parallel builds, we might try to compile the rtc driver too
early.
Change-Id: I9a2681484d58b67ed3061669fbdf52ac5ad14dab
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Reviewed-on: http://review.coreboot.org/1698
Reviewed-by: Marc Jones <marcj303@gmail.com>
Tested-by: build bot (Jenkins)
|
|
When a power failure happens on the RTC rail, the CMOS memory (including
the RTC registers) is filled with garbage.
So, we erase the full first bank (112 bytes) and we reset the RTC date
to the build date.
To test, disconnect the CMOS battery to produce an RTC power
failure, then boot the machine and observe the RTC date is the build
date using "cat /sys/class/rtc/rtc0/date"
Change-Id: I684bb3ad5079f96825555d4ed84dc0f7914e9884
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Reviewed-on: http://review.coreboot.org/1697
Reviewed-by: Marc Jones <marcj303@gmail.com>
Tested-by: build bot (Jenkins)
|
|
Each G34 socket has two node. Previous lapic algorithm is written for
the CPU which has one node per socket. I test the code on h8qgi with
4 family 15 CPUs(8 cores per CPU). The topology is:
socket 0 --> Node 0, Node 1
socket 2 --> Node 2, Node 3
socket 1 --> Node 4, Node 5
socket 3 --> Node 6, Node 7
Each node has 4 cores.
I change the code according to this topology.
Change-Id: I45f242e0dfc61bd9b18afc952d7a0ad6a0fc3855
Signed-off-by: Siyuan Wang <SiYuan.Wang@amd.com>
Signed-off-by: Siyuan Wang <wangsiyuanbuaa@gmail.com>
Reviewed-on: http://review.coreboot.org/1659
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
|
|
This will allow the lower bank to be cleared without impacting the
ability to suspend/resume.
Change-Id: Iaec3c9e7e40c334053c814eaddd1f614df245a73
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1696
Reviewed-by: Marc Jones <marcj303@gmail.com>
Tested-by: build bot (Jenkins)
|
|
On Panther Point PCH (and maybe cougar point), when some of the register
D reserved bits are set, the RTC starts misbehaving (e.g. incrementing
the year byte every second).
There are probably undocumented features implemented behind those bits.
Let's reset register D to a known state to ensure we get the expected
RTC behavior.
Change-Id: I7e2c2a2c6130a974bccb3d760b41eaa579a58b67
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Reviewed-on: http://review.coreboot.org/1695
Reviewed-by: Marc Jones <marcj303@gmail.com>
Tested-by: build bot (Jenkins)
|
|
We always define CONFIG_ variables, even if they're not set.
Hence, remove the check whether CONFIG_UDELAY_TIMER2 is defined
Change-Id: Iefdf2389941f2cc63ae4f13ac6b213da4c96b201
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1694
Reviewed-by: Marc Jones <marcj303@gmail.com>
Tested-by: build bot (Jenkins)
|
|
Right now we only had a post code for "All devices enabled" which
was emitted at the wrong time (after the device initialize stage
rather than the device enable stage)
Change-Id: Iee82bff020de844c7095703f8d6521953003032c
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1693
Reviewed-by: Marc Jones <marcj303@gmail.com>
Tested-by: build bot (Jenkins)
|
|
Our linker script for romstage checks for global variables and
makes the build fail if there are any (on non-AMD systems).
This is great, but having the build fail without any indication
which variables are global is not very useful.
Moving the check to the Makefile allows us to let the linking stage
succeed and reveil which variable names end up in the data and bss
sections of the binary.
To test, add "int foo;" as the first line in src/mainboard/samsung/lumpy/romstage.c
and build coreboot for Lumpy. See the build break the following
way:
LINK cbfs/fallback/romstage_null.debug
Forbidden global variables in romstage:
00006a84 B foo
Change-Id: I3c8780888f46a6577ffd36bcea317997b4f84f6f
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1692
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
|
|
To allow easy experimentation with thermals, leave power control
registers unlocked.
Change-Id: Ia53065f3f220c2faed58e7d53e60c3f169ae58ec
Signed-off-by: Sameer Nanda <snanda@chromium.org>
Reviewed-on: http://review.coreboot.org/1688
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
|
|
Every line of text after a 'help' label in a Kconfig
file must have the same whitespace preceding it, otherwise
it's no longer considered help text.
Change-Id: I97093bee72b295b315d78d4c26d7186bf1017fda
Signed-off-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-on: http://review.coreboot.org/1687
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
|
|
PCIE devices are detected and initialized by the AMD PCIe init functions,
which is in cimx rd890. The parameters are read from devicetree.cb before PCIe init.
Now, all bridges and devices are trained on the device 0.0 enable.
After PCIe init, the PCIe ports with devices are on and the PCIe ports
without devices are off. so resources may be allocated correctly
during the rest of the PCI scan.
But if the devicetree was being used to enable/disable devices after initialization,
the problems would arise. Take a look at the serial log:
do_pci_scan_bridge for PCI: 00:02.0
PCI: pci_scan_bus for bus 01
PCI: pci_scan_bus returning with max=001
do_pci_scan_bridge returns max 1
do_pci_scan_bridge for PCI: 00:03.0
PCI: pci_scan_bus for bus 02
PCI: pci_scan_bus returning with max=002
do_pci_scan_bridge returns max 2
do_pci_scan_bridge for PCI: 00:04.0
PCI: pci_scan_bus for bus 03
PCI: pci_scan_bus returning with max=003
do_pci_scan_bridge returns max 3
PCI bridge 02.0, 03.0 and 04.0 are not inserted devices, but these bridges
are still scanned. This is not correct.
Change-Id: I87dac5f062c6926081970ed0c5f26a7e3f447395
Signed-off-by: Siyuan Wang <SiYuan.Wang@amd.com>
Signed-off-by: Siyuan Wang <wangsiyuanbuaa@gmail.com>
Reviewed-on: http://review.coreboot.org/1640
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
|
|
There are four mainboards using agesa family15 code:
Supermicro h8scm and h8qgi, Tyan s8226 and AMD dinar.
All of these boards' PCI domain starts from 0x18.0. Take h8scm as
an example, PCI devices from 0.0 to 0x14.5 is under 0x18.0.
Now, the PCI domain's scan bus function stats from 0.0. This would
result to the PCI devices be scanned twice. Because when the function
run to device 18.0, it would scan from 0.0 again.
This issue would result to 2 problems:
1) PCI device may be assigned two different PCI address.
If this happenned on VGA device, coreboot maybe not load
vga bios correctly.
2) coreboot initializes rd890's IO APIC twice.
So this patch scans from 0x18.0 and could resolve the problems above.
Change-Id: I90fbdf695413fd24c7a5e3e9b426dc7ca6e128b1
Signed-off-by: Siyuan Wang <SiYuan.Wang@amd.com>
Signed-off-by: Siyuan Wang <wangsiyuanbuaa@gmail.com>
Reviewed-on: http://review.coreboot.org/1639
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
|
|
Adds lowlevel handling of DMAR tables for use by mainboards'
ACPI code. Not much automagic (yet).
Change-Id: Ia86e950dfcc5b9994202ec0e2f6d9a2912c74ad8
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/1654
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Compose the name from Kconfig strings instead.
As the field is for debug print use only, a minor change in the output
should do no harm. The strings no longer include word "Mainboard".
Change-Id: Ifd24f408271eb5a5d1a08a317512ef00cb537ee2
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1635
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
This is the smallest possible change to make early_serial.c
compile when included from romstage.c.
early_serial could be reworked to be built as separate unit
(romstage-y), but that should be done for all SuperIOs,
not some individual outlier.
Change-Id: I90ee66b43c9677b86b1b5d6fcc8febfbe58d80dd
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/1686
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Change-Id: I853454e8f5617fb7af5dddd7288bdeeacc7b1b8e
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/1663
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
All of these capabilities exist on all CPUs supported on
this socket.
Change-Id: I54f34e48e34bb6ab5b9954ab7ece8c2c3a1a8e67
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/1664
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
The constant field "name" in chip_operations is common to multiple
different devices within a chip and cannot reflect the actual device
as found on the platform.
The intention is that a driver sets dev->name as part of the device
enumeration sequence with the detected hardware type and revision.
The field is for debug print use only.
Change-Id: Ib7bf90ba3c618ad0cb715d80d6a937ceaae0adcf
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1634
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
This adds proper support for turbo and super-low-frequency modes.
Calculation of the p-states has been rewritten and moved into an
extra file speedstep.c so it can be used for non-acpi stuff like
EMTTM table generation.
It has been tested with a Core2Duo T9400 (Penryn) and a Core Duo T2300
(Yonah) processor.
Change-Id: I5f7104fc921ba67d85794254f11d486b6688ecec
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1658
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Change-Id: I3efef6bc8f519382ffdd92eb10b4bcd1a4361ba9
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1657
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Because enable cache is added at the end of disable_cache_as_ram,
( http://review.coreboot.org/#/c/1662/2/src/cpu/amd/agesa/cache_as_ram.inc )
enable_cache() should be removed. The 3 mainboards are: amd parmer,
amd thatcher and tyan s8226
Change-Id: If870ca07d2e97b9e860a2e2315f551251c7a4ed2
Signed-off-by: Siyuan Wang <SiYuan.Wang@amd.com>
Signed-off-by: Siyuan Wang <wangsiyuanbuaa@gmail.com>
Reviewed-on: http://review.coreboot.org/1669
Reviewed-by: Marc Jones <marcj303@gmail.com>
Tested-by: build bot (Jenkins)
|
|
Change-Id: Ia3824059a38412896ed2be0c8714018b2291c9f8
Signed-off-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-on: http://review.coreboot.org/1660
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
|
|
add this code according to src/include/cpu/x86/cache.h ,line 92,
functin enable_cache()
Change-Id: Ida96a98397eeed98dd61ca979e8c5a33bf00f9e5
Signed-off-by: Siyuan Wang <SiYuan.Wang@amd.com>
Signed-off-by: Siyuan Wang <wangsiyuanbuaa@gmail.com>
Reviewed-on: http://review.coreboot.org/1662
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
|
|
We parsed the MSR the wrong way, and didn't support some valid values.
Change-Id: Ia42e3de05dd76b6830aaa310ec82031d36def3a0
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1656
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Don't let expat and/or python show the compile process on stdout.
Instead direct this output to crossgcc-build.log.
Fix the logfile path for python.
Change-Id: I431dabf6955d7eef3e54c96d0fb11b92d1cee96d
Signed-off-by: Idwer Vollering <vidwer@gmail.com>
Reviewed-on: http://review.coreboot.org/1667
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Unfortunately the reference tool chain was updated
without ever even testing it on an abuild run. This
broke a number of ports.
This change gets coreboot at least compiling again
for all supported systems.
Change-Id: I92c7cbc834de6d792fdab86b75df339e2874c52e
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1670
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
|
|
This adds a .gitreview file for use with the git-review tool. More
information is available at the URL below:
https://labsconsole.wikimedia.org/wiki/Git-review
Change-Id: I723d78bf7dd81c5756e684d5b166210246fe2daf
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/1665
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
We had only some MSR definitions in there, which are used in speedstep
related code. I think speedstep.h is the better and less confusing place
for these.
Change-Id: I1eddea72c1e2d3b2f651468b08b3c6f88b713149
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1655
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Change-Id: Ia7ef3a4cbc3638a9c9a48b297e392e4e655b6e6b
Signed-off-by: Stefan Tauner <stefan.tauner@gmx.at>
Reviewed-on: http://review.coreboot.org/1581
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Current ExecuteFinalHltInstruction function doesn't work well.
(at least in configuration
Supermicro board with Orochi AMD Opteron processors (model OS6234WKTCGGU))
System reboots when trying to halt core 2,4,6,8 or 10
(OS6234WKTCGGU is 12 core processor)
Based on this information, i think that code doesn't really work with
f15 compute unit (CU) system.
Replacing ExecuteFinalHltInstruction function with
analogous function from f15tn family code fix this problem.
Both functions written from the same cahalt.asm file, but f15tn version
seems more completed
Change-Id: I3942abcdf21f1b86a44c01cc477714e44a40b9cf
Signed-off-by: Kostr <aladyshev@nicevt.ru>
Reviewed-on: http://review.coreboot.org/1569
Tested-by: build bot (Jenkins)
Reviewed-by: Siyuan Wang <wangsiyuanbuaa@gmail.com>
Reviewed-by: Marc Jones <marcj303@gmail.com>
|
|
Enable the PCIE bridge which is connected to the PCIE slot.
Change-Id: I1b3fb59990e06d7bc7cf19639f2b93dbb7bf9b3e
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: zbao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/1098
Tested-by: build bot (Jenkins)
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-by: Marc Jones <marcj303@gmail.com>
|
|
We only want to add data once per device. Using the one in
chip_operations is not very usable anyway, as different
devices under the same chip directory would need to output
entirely different sets of data.
Change-Id: I96690c4c699667343ebef44a7f3de1f974cf6d6d
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1492
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins)
|
|
The number read from the io-apic register represents the index of the
highest interrupt redirection entry, i.e. the number of interrupts
minus one.
Change-Id: I54c992e4ff400de24bb9fef5d82251078f92c588
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1624
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
The options are shown regardless of payload if CONFIG_EXPERT is set.
Change-Id: I12c81ce41a0e300e852481424eadc83f281863bf
Signed-off-by: Peter Stuge <peter@stuge.se>
Reviewed-on: http://review.coreboot.org/1638
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Change-Id: I29fb86ff3a3187b720ce5ef246c4eeee696ab5cd
Signed-off-by: Peter Stuge <peter@stuge.se>
Reviewed-on: http://review.coreboot.org/1637
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Also clarify that enabling these options is generally not desirable if
using SeaBIOS as payload since the option ROMs are run by SeaBIOS with
more complete BIOS interrupt services available than coreboot.
Change-Id: Ic4a45c351a4933aedad08d70a088eab04ca35b05
Signed-off-by: Peter Stuge <peter@stuge.se>
Reviewed-on: http://review.coreboot.org/1636
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Details for this board are available at
http://usa.ieiworld.com/product_groups/industrial/content.aspx?gid=00001000010000000001&cid=09050662496936266123&id=09034367569861123956
Support for the IT8888 PCI to ISA bridge will be added in a later
patch.
Change-Id: Iaefe47f5ad405a56d230c929e5850156eb0f60ae
Signed-off-by: Ricardo Martins <rasmartins@gmail.com>
Reviewed-on: http://review.coreboot.org/1152
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
Output values of 64bit registers and fix settings for GPE0_EN for
ICH9/10.
Change-Id: I8ca6b32500331707670972b38466345f581844cd
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1625
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Peter Stuge <peter@stuge.se>
|
|
This adds a new interface for storage devices. A driver for ATA and
ATAPI drives on AHCI host controllers comes along.
The interface is very simple and was designed to match FILO's needs.
It consists of three functions:
void storage_initialize(void);
Initializes controllers. Should be called once at startup.
storage_poll_t storage_probe(size_t dev_num);
with typedef enum {
POLL_NO_DEVICE = -2,
POLL_ERROR = -1,
POLL_NO_MEDIUM = 0,
POLL_MEDIUM_PRESENT = 1,
} storage_poll_t;
Looks for a drive with number dev_num (drives are counted from
zero) and polls for a medium in the drive if appropriate.
int storage_read_blocks512(size_t dev_num,
u64 start, size_t count,
unsigned char *buf);
Reads count blocks of 512 bytes from block start of drive dev_num
into buf.
Change-Id: I1c85796b7f8e379ff3817a61b1837636b57e182b
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1622
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Peter Stuge <peter@stuge.se>
|
|
Change-Id: Ic44915cdb07e0d87962eff0744acefce2a4845a2
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1626
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-by: Peter Stuge <peter@stuge.se>
|
|
Change-Id: I7fcf190ef92b06b857d8b85c3d27da9cdee071b1
Signed-off-by: Stefan Tauner <stefan.tauner@gmx.at>
Reviewed-on: http://review.coreboot.org/1633
Tested-by: build bot (Jenkins)
Reviewed-by: Peter Stuge <peter@stuge.se>
|
|
This adds...
- generated documentation files
- all kinds of stuff in the util subdirectories
Change-Id: I47ab6d239aae725f54413f03424f40002ac5a275
Signed-off-by: Stefan Tauner <stefan.tauner@gmx.at>
Reviewed-on: http://review.coreboot.org/1572
Tested-by: build bot (Jenkins)
Reviewed-by: Peter Stuge <peter@stuge.se>
|
|
Change-Id: I9db10e8c7dcd693cc4ab935c587da02dd7eb2bc5
Signed-off-by: Idwer Vollering <vidwer@gmail.com>
Reviewed-on: http://review.coreboot.org/1621
Tested-by: build bot (Jenkins)
Reviewed-by: Peter Stuge <peter@stuge.se>
|
|
Change-Id: Id0b736d402b33138e27b18c74e5ed8ffab0bcccb
Signed-off-by: Idwer Vollering <vidwer@gmail.com>
Signed-off-by: Peter Stuge <peter@stuge.se>
Reviewed-on: http://review.coreboot.org/1620
Tested-by: build bot (Jenkins)
|
|
The PCI registers should be accessed aligned and 0x62 is not 32bit
aligned therefore this patch changes it to a 16bit access.
Change-Id: I00725a4569f471eedb061834f626911b42e734fb
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-on: http://review.coreboot.org/1631
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Tested-by: build bot (Jenkins)
|
|
Without this, the output of "Setting up ACPI…" continues right
after the output of stepping.
Change-Id: I2ad7cc3e55884ff509600b01274258b8e8250981
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-on: http://review.coreboot.org/1632
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Tested-by: build bot (Jenkins)
|
|
This is not available as a config option anymore.
Change-Id: Icac173d62928423a08671321ec21d4af82c5cded
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-on: http://review.coreboot.org/1630
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Tested-by: build bot (Jenkins)
|
|
I don't know if the size main memory supposed to be in PCI(0,0) reg 0x9c
but it is not written there. The size of memory is written in
src/northbridge/intel/sch/raminit.c to SCH port(2, 8, 4) (look for
"Setting up TOM").
Change-Id: Iea04a5185bda56f61d1c382533d5a0dac429ebbd
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-on: http://review.coreboot.org/1629
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
|
|
The GGC register which contains the size of memory that is used for GPU
is in PCI device 2,0 and not 0,0. It is set to to 4MiB in
src/mainboard/iwave/iWRainbowG6/romstage.c.
Change-Id: Ie9f1cc60544ecd9cad770f34c83c33564a6129d4
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-on: http://review.coreboot.org/1628
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
|
|
Without this, the hightables are placed just before the end of memory.
However we might have the GPU memory located at the exact same spot,
that is in the last 4 MiB. So without this patch, this area won't remain
marked as "CONFIGURATION TABLES" within coreboot's memory table but
becomes "RESERVED" because it is part of the PCI(2,0) device.
Change-Id: Ibd111c167c2f6ac03b0ba68581a74ecbd2c9c160
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-on: http://review.coreboot.org/1627
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
|
|
Correct the download URL of mingw's w32api.
Change-Id: I98fb43c121399c23f6693ade5cd3b42bc9463724
Signed-off-by: Idwer Vollering <vidwer@gmail.com>
Reviewed-on: http://review.coreboot.org/1619
Tested-by: build bot (Jenkins)
Reviewed-by: Peter Stuge <peter@stuge.se>
|
|
Change-Id: I7cd63248eb8abb711cecce41e3f8a282b34aa126
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/1548
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
This patch updates crossgcc to download and compile mingwrt 3.20-2
Change-Id: Ic5ed2df4c3643e469a62c51643d3fc756eb3e615
Signed-off-by: Idwer Vollering <vidwer@gmail.com>
Reviewed-on: http://review.coreboot.org/1617
Reviewed-by: Peter Stuge <peter@stuge.se>
Tested-by: build bot (Jenkins)
|
|
This patch updates crossgcc to download and compile binutils 2.23
Change-Id: I75a24ce6fb9f6ac7ae53671314c410b9b0d80aa8
Signed-off-by: Idwer Vollering <vidwer@gmail.com>
Reviewed-on: http://review.coreboot.org/1615
Tested-by: build bot (Jenkins)
Reviewed-by: Peter Stuge <peter@stuge.se>
|
|
This patch updates crossgcc to download and compile MPC 1.0.1
Change-Id: I7a2a21afc8c26e4fb7b6553c7fd98cc054d01570
Signed-off-by: Idwer Vollering <vidwer@gmail.com>
Reviewed-on: http://review.coreboot.org/1614
Tested-by: build bot (Jenkins)
Reviewed-by: Peter Stuge <peter@stuge.se>
|
|
This patch updates crossgcc to download and compile MPFR 3.1.1
Change-Id: I6c479db5d6d632dcc2201c3771b43e2b663877e1
Signed-off-by: Idwer Vollering <vidwer@gmail.com>
Reviewed-on: http://review.coreboot.org/1613
Tested-by: build bot (Jenkins)
Reviewed-by: Peter Stuge <peter@stuge.se>
|
|
This patch updates crossgcc to download and build GDB 7.5
Change-Id: I38fc3591396f072ead399b22f516ec765480ea40
Signed-off-by: Idwer Vollering <vidwer@gmail.com>
Reviewed-on: http://review.coreboot.org/1612
Tested-by: build bot (Jenkins)
Reviewed-by: Peter Stuge <peter@stuge.se>
|
|
Update crossgcc to use gcc 4.7.2.
This requires a minor change to util/crossgcc/buildgcc as well.
Tested on hardware with asus/p2b and lenovo/x60.
Change-Id: Ia3921844670ca99741e5715def14dd969f305ab7
Signed-off-by: Idwer Vollering <vidwer@gmail.com>
Reviewed-on: http://review.coreboot.org/1609
Tested-by: build bot (Jenkins)
Reviewed-by: Peter Stuge <peter@stuge.se>
|
|
Compilation of acpica-20120420 is broken (and old, but I'll take care
of that in a future patch),
let's fix that ("Building IASL 20120420 ... failed").
Change-Id: If5fd5cd93d748f78b7c059323f9f810666e32cc7
Signed-off-by: Idwer Vollering <vidwer@gmail.com>
Reviewed-on: http://review.coreboot.org/1607
Tested-by: build bot (Jenkins)
Reviewed-by: Peter Stuge <peter@stuge.se>
|
|
Change-Id: I2f10909a626fb64c7f95663ddd79a3b899f73bc4
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/1606
Tested-by: build bot (Jenkins)
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-by: Marc Jones <marcj303@gmail.com>
|
|
Change-Id: Ie4e4a2f0d68643a8f46d24ee7bd1b953e9fe14a5
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/1605
Tested-by: build bot (Jenkins)
Reviewed-by: Peter Stuge <peter@stuge.se>
|
|
regex, pdcurses, wsock(for itohl) are seperated libraries. mmap and unmmap are
ported from git.
Issues:
1. The length of command line is limited. That makes the Thather can not be built
because too many obj.o need to be built.
Change-Id: I1d60ec5c7720c1e712e246c4cd12e4b718fed05f
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/1604
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
The default gcc on mingw will process the __attribute__ ((packed)) in
a different way other than non-win system.
Change-Id: Iac9f4476c922472d0b447f1c3ef60e8e13bd902f
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/1603
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
make distclean causes error on mingw:
-------
rm: cannot lstat `build/util': Permission denied
make: *** [distclean] Error 1
-------
Guess, When the distclean is made by multi-process, the mkdir
in the Makefile will execute when build is removed. That causes
conflicts.
Change-Id: Ia41ecc5d1db2fa9d3328c81ac1d33fa94779492d
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/1602
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
Change-Id: Id5564bf7a12b3ea9a5e60bd9522466157ace8c65
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/1601
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
|
|
src/vendorcode/amd/agesa/f15/Porting.h has some conflicted typedef with
src/include/cpu/amd/common/cbtypes.h. These conflicted defines can lead to errors.
Change-Id: Idad0794018bf0bd0e4e52a5aa062a12766d56c8e
Signed-off-by: Siyuan Wang <SiYuan.Wang@amd.com>
Signed-off-by: Siyuan Wang <wangsiyuanbuaa@gmail.com>
Reviewed-on: http://review.coreboot.org/1592
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
