| Age | Commit message (Collapse) | Author |
|---|
|
When booting kahlee, there's an error message: "Warning: Can't write PCI
IRQ assignments because 'mainboard_pirq_data' structure does not exist".
This is generated by write_pci_cfg_irqs due to missing mainboard_pirq_data.
BUG=b:70788755
TEST=Build and boot kahlee. Warning message must be gone.
Change-Id: If07d2f54f06f6cf77566c43eddc8ee8a314e7a3a
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/22940
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Change-Id: I6dfef118dc2fecf2a8f2f3401c779a3becfb71a9
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/23522
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
Change-Id: I8c49853a54fc301d39dc7c362f2085c25fad7fbd
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/23433
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
The designware i2c controller indicates that the slave address
shouldn't be programmed while the controller is enabled. Therefore,
switch the ordering of the slave target address and the enable.
Additionally, ensure the controller is disabled prior to the
start of the slave programming sequence.
Lastly, chunk up the i2c_msg segments at differing slave address
boundaries. That allows for simpler programming for the controller
by only doing one slave address transaction chunk at a time.
BUG=b:70232394,b:69250772
Change-Id: Iebc08e2db847cb182fad98e0ff3d799b9a64aca7
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/23513
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Part of the original patch, commit 85a90e1, reverted edk2 commit:
1d7258f [CorebootModulePkg:Removing EFI_RESOURCE_ATTRIBUTE_TESTED]
which had the unintended effect of causing memory above 2GiB
from being unavailable (marked reserved) when booting without a
connected display (aka headles mode).
This commit strips the patch to only the component needed to fix
reading of the coreboot table low memory pointer.
TEST: boot 4GB google/panther without connected display, verify
memory above 2GB available via 'dmesg | grep BIOS-e820' and 'free -m'
Change-Id: I39327929f9b0b940fc12cdca1d744456fdc097e0
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/23483
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
This fixes tianocore garbled framebuffer when 'x_resolution *
bits_per_pixel / 8' is not equal to 'bytes_per_line'.
This patch was also send to the edk2-devel mailing list:
https://lists.01.org/pipermail/edk2-devel/2018-January/020436.html
Tested on Thinkpad X220 with libgfxinit on 1366x768 display.
Change-Id: Ib9eaf692f86d416cd4ec3cc73a8b0aa0a28a38dd
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/23403
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
|
|
FSP_GOP needs a vbt.bin to work but before this patch it was able to
build with the default configuration which was an empty path for
vbt.bin.
To make Jenkins happy don't select FSP_GOP by default, at least until
all boards have the proper vbt blobs in the blobs repo.
Change-Id: Ibc36d6d4dd1a56c53819b169e6f4799ce3c23e03
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/23290
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
Update the shared AGESA headers to 1.3.0.9.
This depends on 3rdparty/blobs/pi/amd/00670F00/ binaries updated
to the same version.
BUG=b:72679320
TEST=build and boot Grunt
Change-Id: I783b7318e8273913f753b70f12bfe8b71274e27f
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/23547
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Communicate additional status to the console when the save and load
functions do not function as expected. The most likely scenario for
an error is when using a cache that is external to cbmem, and restricted
in size.
Change-Id: Ic9a709c11152b3b9cb40abfc204151f9636b5a4c
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/23517
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Revert most of 4f3f47b "amd/common: Define regions in cbmem". This
puts the management of the heap space back to its traditional
methodology. Subsequent patches that were to have used these
subregions have been reworked.
BUG=b:69614064
Change-Id: Ib3d40bcf61c50dbc481b60e7b5286f65a529b912
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/23516
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
To set address on AMD, IC_ENABLE == 0.
BUG=b:69416132
BRANCH=none
TEST=Test communication with i2c TPM on grunt and coral
Change-Id: I7faee8e11439deceab946cc82d30d274b529b90d
Signed-off-by: Chris Ching <chingcodes@chromium.org>
Reviewed-on: https://review.coreboot.org/23293
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
|
|
The kernel requires the display oprom is loaded *and* ran
in order for the kernel to not panic. Therefore, select the
correct settings such that normal mode works for Chrome OS.
BUG=b:72400950
Change-Id: Ibae5bc6b382cbe71a55c2386a24bb420cb8f313f
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/23506
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Certain platforms require that the option rom always needs to be
ran in order for display to work correctly. Therefore, provide
this ability for the platform to select such that we force option
rom loading.
BUG=b:72400950
Change-Id: I597bc8af7ac8b68fe8505aac5f1c7e1ccd34ac27
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/23505
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Use C if conditions instead of preprocessor macros.
BUG=b:72400950
Change-Id: I8107f94b9ecb6f32c569cad0bcb3d51ab39aa35c
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/23504
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Delay making TSEG valid until the end of POST. After the CPU setup,
there are times where coreboot needs to access the SMRAM from outside
of SMM. Also relocate locking of the SMM settings from the CPU init
to the end of POST (or just before resuming).
Change-Id: I70b7e33e7045d397e41f571caff6a2acbb64eaab
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/23437
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Extend the values reserved for AGESA to include the Entry Points used
for S3 Resume.
BUG=b:69614064
Change-Id: I6b50e76a0c49c1f317f9294c5f95735e7aa5d95c
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/23439
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This commit adds an entry for H1/Cr50 into the devicetree for setting up
ACPI entries for H1 communication.
BUG=b:69250772
TEST=See probe messages in dmesg
Change-Id: Id55ce3364ea4acdb62782758e5bcb2a167286cb9
Signed-off-by: Justin TerAvest <teravest@chromium.org>
Reviewed-on: https://review.coreboot.org/23514
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This commit removes a manually written asl file in favor of configuring
the trackpad through devicetree.
BUG=b:72121803
TEST=cat /proc/interrupts with trackpad connected
Change-Id: I38afcf89ea64ffaf6a10bb317c41154feda57e50
Signed-off-by: Justin TerAvest <teravest@chromium.org>
Reviewed-on: https://review.coreboot.org/23508
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
chromeec uses libftdi1-dev, so add it to the image.
Change-Id: I517e3f073062dcc6b0b8e3adaf7b0123290a1698
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/23482
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
The code has been moved into drivers folder.
Change-Id: I122affffd5108052ed7a95b34d0d66a6d3279d41
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/23487
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Provide the PM1_TMR information in the FADT even if PmTimerDisabled is
set because PM timer emulation is enabled via MSR 121h so the timer will
still work and can be used by things like Tianocore and Windows.
Change-Id: I78e435c34dd4e6241d345c4d07470621ea051fb8
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/23510
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
The calculation to set up the PM timer emulation is using an
incorrect common timer clock value that was copied from Apollolake.
According to the PDG Skylake and Kabylake clocks are derived from a
24MHz XTAL, not 19.2MHz like Apollolake.
Fixing this value results in the proper "correction value" to be
programmed into the PM timer emulation MSR that matches the raw value
that would be programmed by FSP. (if it were doing MpInit)
Old PM timer correction value: 0x2fba2e25
New PM timer correction value: 0x262e8b51
Change-Id: Ib2bb3cb1938ae34cfa7aef177bef6fc24da73335
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/23509
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Write _ROM method and store PCI Option ROM in CBMEM.
Allows an EFI compatible OS to retrieve the Option ROM without the need
to access the PCI BAR. As the Option ROM is no longer present in the
legacy VGA area it's required for mobile platforms. On hybrid devices,
like Lenovo Thinkpads supporting NVIDIA Optimus it's the only way to
retrieve the Option ROM, even with legacy BIOS, as there's no PCI BAR to
map.
Tested on:
* Lenovo T530
* Linux Kernel 4.13.7
* nouveau
Change-Id: I548b730fb64833083cc05af5b21dd6959804224b
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/20548
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Generate ACPI AML code for _ROM method.
This function takes as input ROM data and ROM length.
Arguments passed into _DSM method:
Arg0 = Offset in Bytes
Arg1 = Bytes to return
Example:
acpigen_write_rom(0xdeadbeef, 0x10000)
AML code generated would look like:
Method (_ROM, 2, NotSerialized) // _ROM: Read-Only Memory
{
OperationRegion (ROMS, SystemMemory, 0xdeadbeef, 0x00010000)
Field (ROMS, AnyAcc, NoLock, Preserve)
{
Offset (0x00),
RBF0, 524288
}
Local0 = Arg0
Local1 = Arg1
If (Local1 > 0x1000)
{
Local1 = 0x1000
}
If (Local0 > 0x00010000)
{
Return (Buffer (Local1)
{
0x00
})
}
If (Local0 > 0x0f000)
{
Local2 = 0x10000 - Local0
If (Local1 > Local2)
{
Local1 = Local2
}
}
Name (ROM1, Buffer (Local1)
{
0x00
})
Local1 *= 0x08
Local0 *= 0x08
CreateField (RBF0, Local0, Local1, TMPB)
ROM1 = TMPB /* \_SB_.PCI0.GFX0._ROM.TMPB */
Return (ROM1) /* \_SB_.PCI0.GFX0._ROM.ROM1 */
}
Change-Id: Ie118b15257295b7133c8e585c0fd5218249dec8d
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/20547
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Select DISPLAY_FSP_VERSION_INFO Kconfig to get all required
firmware information right after FSP-S.
TEST=Display FW information as below
>> Display FSP Version Info HOB
Reference Code - CPU = 7.1.20.52
uCode Version = 0.0.0.16
Reference Code - ME 11.0 = 7.1.20.52
MEBx version = 0.0.0.0
ME Firmware Version = Consumer SKU
Reference Code - CNL PCH = 7.1.20.52
PCH-CRID Status = Disabled
CNL PCH H A0 Hsio Version = 2.0.0.0
CNL PCH H Ax Hsio Version = 9.0.0.0
CNL PCH H Bx Hsio Version = 5.0.0.0
CNL PCH LP Ax Hsio Version = 13.0.0.0
CNL PCH LP B0 Hsio Version = 7.0.0.0
CNL PCH LP Bx Hsio Version = 6.0.0.0
CNL PCH LP Dx Hsio Version = 2.0.0.0
Reference Code - SA - System Agent = 7.1.20.52
Reference Code - MRC = 0.5.1.19
SA - PCIe Version = 7.1.20.52
SA-CRID Status = Disabled
SA-CRID Original Value = 0.0.0.0
SA-CRID New Value = 0.0.0.0
Change-Id: Ibfcac0002998e8a6594bb6dfc68b2577f62ddbff
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/23387
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch locates FSP FVI hob in order to extract all firmware
ingredient version information.
So far this feature is only supported for CannonLake SoC onwards.
Change-Id: Ib749e49a9f263d85947b60d4c445faf8c37f5931
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/23386
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Base patch to create Firmware Version Info (FVI) for CannonLake coreboot
platform using CannonLake FSP new feature.
Expectation is that, FSP will provide version information of all Firmware
ingredient its equip with (i.e. CPU Ref Code, uCode version, MCH Ref Code,
CSE Sku type, CSE version, System Agent Ref Code, OpRom Version, GOP version,
PCH Ref Code version etc.)
Change-Id: Ic388e036709190e8d5c5010f4ea87223291f21d0
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/23385
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Update Cannonlake FSP header to revision 7.x.20.52. Following changes
had been made:
1. Hide internal EV related options.
2. Add GT voltage override options.
3. Add PEG IMR selection.
4. Add PCH DMI ASPM options.
TEST=NONE
Change-Id: If186a1eb440266f1eaeb03505fe0ff4c6a521be6
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/23351
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
|
|
This patch ensures MemInfoHob.h file can make use of existing UEFI
headers as is rather than redefining the same structure locally.
TEST=Download BIOS_Version_122.3 from external github and
build MemInfoHob.h without any compilation error.
Change-Id: Ic1e0ad94d8e40ac2aefe9fbcea7d684a97c864b4
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/23355
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Users are getting build error due to duplicate macro definitions
of same resource type between fsp driver code and UEFI headers.
Hence this patch ensures to refer a single source location for
macro definitions to avoid compilation error.
Change-Id: If022eb29550a9310b095bff6130b02fb0a25ef7a
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/23356
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This patch ensures if required SoC/FSP driver code can retrieve
UDK version for a platform.
Change-Id: I3120ce512255ed6f2a40413e8e6d8000c7285b39
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/23374
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Now SOC code can select the require UDK support package for any
platform going forward with FSP2.0 model.
Change-Id: Ie6d1b9133892c59210a659ef0ad4b59ebf9f1e45
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/23426
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This patch includes (edk2/UDK2017) all required headers for UDK2017
from EDK2 github project using below command
>> git clone https://github.com/tianocore/edk2.git vUDK2017
commit hash: 66833b2a87d98be8d81d1337c193bcbf0de47d47
Change-Id: If0d5a3fef016c67e9eed6aed9b698b3b13b930c4
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/23425
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This change uses gpio_keys driver to add ACPI node for pen eject event.
BUG=b:71329519
TEST=Verified using evtest that pen eject event results in events as
expected.
Change-Id: Ib293c2ca532c8ed9e2587143b1a69300cd9fa4e9
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/23238
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
This change adds the required device node in SSDT for defining
gpio-keys/gpio-keys-polled. Currently, it supports only one gpio-key
per device node.
BUG=b:71329519
TEST=Verified by adding details to devicetree that device node is
added to SSDT:
Device (PENH)
{
Name (_HID, "PRP0001") // _HID: Hardware ID
Name (_CRS, ResourceTemplate () // _CRS: Current Resource Settings
{
GpioIo (Exclusive, PullDefault, 0x0000, 0x0000, IoRestrictionInputOnly,
"\\_SB.PCI0.GPIO", 0x00, ResourceConsumer, ,
)
{ // Pin list
0x002B
}
})
Name (_DSD, Package (0x04) // _DSD: Device-Specific Data
{
ToUUID ("daffd814-6eba-4d8c-8a91-bc9bbf4aa301") /* Device Properties for _DSD */,
Package (0x01)
{
Package (0x02)
{
"compatible",
"gpio-keys"
}
},
ToUUID ("dbb8e3e6-5886-4ba6-8795-1319f52a966b"),
Package (0x01)
{
Package (0x02)
{
"button-0",
"EJCT"
}
}
})
Name (EJCT, Package (0x02)
{
ToUUID ("daffd814-6eba-4d8c-8a91-bc9bbf4aa301") /* Device Properties for _DSD */,
Package (0x04)
{
Package (0x02)
{
"linux,code",
0x0F
},
Package (0x02)
{
"linux,input-type",
0x05
},
Package (0x02)
{
"label",
"pen_eject"
},
Package (0x02)
{
"gpios",
Package (0x04)
{
\_SB.PCI0.I2C0.PENH,
Zero,
Zero,
One
}
}
}
})
}
Change-Id: I6f11397b17d9de1c87d56f6a61669ef4052ec27b
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/23236
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
ff4025c5f "sb/intel/bd82x6x: Reduce function-disable mess"
Removed most of the writes to RCBA(FD) and renamed the function to
mainboard_rcba_config.
Writes to FD are properly handled in ramstage, so no need to do it in
romstage.
Change-Id: I4edb75569ceec2d2f1308755a66d286202ca0ae6
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/23486
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
Turn on power for front camera at startup in coreboot (needs
to be set for factory scan).
BUG=b:69011806
BRANCH=master
TEST=none
Change-Id: I2f31b19dfef5fe386b485dd675f0ff981288acf4
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/23503
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Fix incorrect settings in the Hynix 4GB and Samsung 2GB SPD files
for meowth.
BUG=b:69011806
BRANCH=none
TEST=Confirm meowth with Hynix 16GB and meowth with Samsung 8GB
solutions boot.
Change-Id: Ia2ac564541b57647c3b605ce3389d74251490ca0
Signed-off-by: Nick Vaccaro <nvaccaro@chromium.org>
Reviewed-on: https://review.coreboot.org/23388
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Enable I2C #2 for display backlight controller.
BUG=b:69011806
BRANCH=none
TEST=none
Change-Id: I5440bd4265414c55458a73e293a9931145a158cc
Signed-off-by: Nick Vaccaro <nvaccaro@chromium.org>
Reviewed-on: https://review.coreboot.org/23392
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Change GPIO settings for meowth rev 2 boards.
Changes include:
- GPP_B7 set to no-connect
- GPP_C1 set to no-connect
- GPP_D8 set to no-connect
- GPP_D9 (PP3300_WLAN_EN) set as output with initial value high
- GPP_E9 (DCI_CLK) set to no-connect
- GPP_E10 (DCI_DATA) set to no-connect
BUG=b:72202352
BRANCH=none
TEST=none
Change-Id: I2e6d049faaa0a70b40ceb47aaf81a81d820dd4c1
Signed-off-by: Nick Vaccaro <nvaccaro@chromium.org>
Reviewed-on: https://review.coreboot.org/23391
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Set USB2 port 0 & 1 to use OC2 and OC3 respectively. Previous settings
were causing false overcurrent conditions as OC0 and OC1 were used for
other purposes.
Remove initialization of unused usb3 ports, and configure the ports we
use (usb3 ports 0 & 1) to use OC2 and OC3, respectively.
BUG=b:72250084
BRANCH=none
TEST=Verify meowth can recognize and boot off a kernel on USB drive.
Change-Id: I528b67d80a1da84e5307facb40de545089979f57
Signed-off-by: Nick Vaccaro <nvaccaro@chromium.org>
Reviewed-on: https://review.coreboot.org/23390
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This change updates the passive setting for TCPU as per factory team
recommendation.
BUG=b:65467566
Change-Id: I081f63bdf811ff021c398f60efec9e6cccf462d5
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/23494
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change selects EC tablet event and provides trip point
temperatures for tablet and non-tablet mode so that DPTF can
be supported depending upon device mode.
BUG=b:65467566
TEST=Verified by changing modes that the trip point temperatures are
updated in the
OS (/sys/devices/virtual/thermal/thermal_zone{2,3,4,5}).
Change-Id: I071868982fa87821550b870a6d8050cf2a030b49
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/23463
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
|
|
This change adds support for:
1. Handling thermal trip points change event handler based on device
mode.
2. Returning thermal trip point temperatures based on the device mode.
BUG=b:72554519
Change-Id: Ife48af76ceb7a39abd1fac8ef1f77db7e65ab43e
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/23462
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
|
|
This change decouples EC tablet event and TBMC device by guarding
TBMC definition and notification using EC_ENABLE_TBMC_DEVICE. It
allows mainboards to use tablet events without having to define a TBMC
device.
BUG=b:72554519
Change-Id: Ie38b6d68486e8e644dd0d6d406def3ae7fdb5152
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/23461
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
|
|
Grunt (a amd-stoneyridge based platform) uses a GPIO to interface with
the tpm. This change allows devicetree entries to use a irq_gpio entry
to describe the interface with the TPM.
BUG=b:72655090
Change-Id: I08289891408d7176f68eb9c67f7a417a2448c2de
Signed-off-by: Justin TerAvest <teravest@chromium.org>
Reviewed-on: https://review.coreboot.org/23500
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
The gpios for 147 and 148 are connected to PCH_I2C_HUB_SCL and
PCH_I2C_H1_TPM_SDA, respectively. Fix the comment.
BUG=b:64140392
Change-Id: Ibebf6ce7d9fb26276b12b9c9844c260413f0337e
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/23499
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
|
|
Since the h1 i2c bus is required for verstage mark the bus
as needing to be initialized early. That way, the bus is initialized
in bootblock prior to verstage.
BUG=b:70232394,b:69250772
Change-Id: Ice8525e08ccb438bc468d4c8bd311f72eddc7eb6
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/23498
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
|
|
Initialize the i2c buses that are marked as early init in the device
tree.
BUG=b:70232394,b:69250772
Change-Id: Iced1797f3bb4765646736c423b081cdc33c12a48
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/23497
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
|
|
The path for the GPIO devices needs to be '\_SB', not '\SB'. Fix
the path so that it references the system bus.
BUG=b:72121803
Change-Id: I7c6c38ecea0f8f95ff52b3390f92c5b7e79bcd6d
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/23501
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The SPI controller on stoneyridge apparently has a large fifo
and an alternate method for programming the controller. The
fifo is directly accessible as well as the rx and tx pointer
in addition to the execute bit. Remove the unneeded #defines
and program the host controller with the above changes in mind.
In addition, add debug hooks to the driver so one can dump the
state of the controller when in operation.
The time it took to read 4KiB of flash in the elog driver went
from 20593 microseconds to 5693 microseconds on cdx03/kahlee.
BUG=b:65485690
Change-Id: Ie7ea9d18cef5511686700ad9b2b9fdfeb6d5685b
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/23493
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The spi flash host controller has a dedicated register for the
opcode. Therefore, indicate to the spi subsystem that the opcode
size should not be taken into account when determining maximum
payload size in spi_crop_chunk(). This allows the full use of
the fifo when doing transfers.
BUG=b:65485690
Change-Id: Iab27a69ca72fd02bc443f0673983f3b22ffca0f5
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/23492
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
|
|
spi_crop_chunk() currently supports deducting the command length
when determining maximum payload size in a transaction. Add support
for deducting just the opcode part of the command by replacing
deduct_cmd_len field to generic flags field. The two enums supported
drive the logic within spi_crop_chunk():
SPI_CNTRLR_DEDUCT_CMD_LEN
SPI_CNTRLR_DEDUCT_OPCODE_LEN
All existing users of deduct_cmd_len were converted to using the
flags field.
BUG=b:65485690
Change-Id: I771fba684f0ed76ffdc8573aa10f775070edc691
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/23491
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Innolux didn't deliver a working init sequence yet for devices without
OTP programming. The sequence in this change has been derived from a
register dump of a mostly working panel with OTP. It is not meant to
be final, but to make devices with unprogrammed OTP work, while Innolux
is figuring out a proper sequence. There is a known issue with an
artifact line in the lower third of the display.
Change-Id: I7096506208e4cb29c5f31a7ac502231a6c23ac92
Signed-off-by: Lin Huang <hl@rock-chips.com>
Reviewed-on: https://review.coreboot.org/23311
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Some panels need to transfer initial code, and some of them will be
over 3 bytes, so support LONG_WRITE type in driver. Refactor mipi
dsi transfer function to support it.
Change-Id: I212c14165e074c40a4a1a25140d9e8dfdfba465f
Signed-off-by: Lin Huang <hl@rock-chips.com>
Reviewed-on: https://review.coreboot.org/23299
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Set PsysPl2 values to 90% of max adapter power for all types of
adapters (typeC and barrel jack) to account for a 10% power loss from
the adapter to the soc.
BUG=b:71594855
BRANCH=None
TEST=reboot device and make sure Pl2 and PsysPl2 MSRs are properly set
with iotools rdmsr command on both U42 and U22 skus with both
typeC and barrel jack power adapters.
Change-Id: I8425c6d4d669449eccb9324ff58ff6d1662c5c43
Signed-off-by: Shelley Chen <shchen@chromium.org>
Reviewed-on: https://review.coreboot.org/23457
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
I measured the rise and fall times for I2C bus 1 from userspace
manually, using "i2cdetect 1" called from userspace and an oscilloscope.
This commit fixes the values there to reflect reality.
BUG=b:72442912,b:70232394
Change-Id: I4f593cb2674006060cad9a77753c23f7d9828c9b
Signed-off-by: Justin TerAvest <teravest@chromium.org>
Reviewed-on: https://review.coreboot.org/23459
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Chris Ching <chingcodes@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The filelist target has been around for a while, but was never added
to the help. Add it now.
Change-Id: Idc24ecc8028fc61c6b798c0c81431b05dfa25b0e
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/23472
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
This fixes the warning that is seen on the jenkins server:
Insecure dependency in piped open while running setgid at
util/lint/checkpatch.pl line 958.
Change-Id: I476efa76ef6a275584a47ec0ecf2315948d53e9d
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/23473
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Change-Id: I12ebed30de4df9814ccb62341c7715fc62c7f5b9
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Signed-off-by: Pratik Prajapati <pratikkumar.v.prajapati@intel.com>
Reviewed-on: https://review.coreboot.org/23431
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
|
|
Harcuvar is the board name, Denverton is the SoC. So macros in files under
soc/ should be named after the SoC not the board.
Change-Id: I1c7d5b93fba386b8e9bd86cf599508e642e21a75
Signed-off-by: Julien Viard de Galbert <jviarddegalbert@online.net>
Reviewed-on: https://review.coreboot.org/23404
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Shine Liu <shine.liu@intel.com>
Reviewed-by: Vanny E <vanessa.f.eusebio@intel.com>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
The scratch registers in northbridge used for storing the top of
cacheable memory are volatile. Use the BiosRam storage in the FCH
instead.
TEST=Suspend and resume Kahlee with complete S3 patch stack
BUG=b:69614064
Change-Id: Ieb3cfd173c70bf899a6391d62d1df87b38485f30
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/22726
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
The spi_flash_cmd_read_fast() and spi_flash_cmd_read_slow() were just
passing full size buffers to the spi controller ops. However, the
code wasn't honoring what the spi controller can actually perform.
This would cause failures to read on controllers when large requests
were sent in. Fix this by introducing a
spi_flash_cmd_read_array_wrapped() function that calls
spi_flash_cmd_read_array() in a loop once the maximum transfer size is
calculated based on the spi controller's settings.
BUG=b:65485690
Change-Id: I442d6e77a93fda411cb289b606189e490a4e464e
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/23444
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
|
|
Both early platform information reporting in bootblock and common code
CPU driver will add support for cannonlake D0 stepping processor.
BUG=None
TEST=Boot up system with D0 stepping CPU installed, check serial log
that can display as D0 stepping.
Change-Id: I76ee974ee027100d7853a110f95b1601987492e4
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/23350
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Pratikkumar V Prajapati <pratikkumar.v.prajapati@intel.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
If not, legacy COM ports will be enumerated by kernel and console will
not work.
localhost ~ # cat /proc/tty/driver/serial
serinfo:1.0 driver revision:
0: uart:16550A port:000003F8 irq:4 tx:0 rx:0
1: uart:16550A mmio:0xC112D000 irq:4 tx:764 rx:0 RTS|DTR
2: uart:16550A mmio:0xC112F000 irq:6 tx:0 rx:0
3: uart:unknown port:000002E8 irq:3
With this fix:
0: uart:16550A mmio:0xC112D000 irq:4 tx:0 rx:0
1: uart:16550A mmio:0xC112F000 irq:6 tx:858 rx:42 RTS|DTR
2: uart:unknown port:000003E8 irq:4
3: uart:unknown port:000002E8 irq:3
Change-Id: Iac5bf65900e090d4e785e0cd828272ebff209458
Signed-off-by: Ravi Sarawadi <ravishankar.sarawadi@intel.com>
Reviewed-on: https://review.coreboot.org/23219
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Change the BiosRam read/write functions to use the fixed MMIO range at
0xfed80500. This is faster than two accesses per byte when using I/O
0xcd4/0xcd5.
Note that BiosRam may only be accessed byte-by-byte. It does not decode
normally.
Change-Id: I9d8baf2bd5d9d48a87bddfb6a0b86e292a8fdf7d
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/23436
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
|
|
This uses the functions in include/mrc_cache.h instead of
northbidge/intel/common/mrc_cache.h
Tested working on Lenovo Thinkpad x220, mrc_cache region gets written
and S3 resume still works fine.
Change-Id: I46002c0b19a55d855286eb8b0ca934ef7ca7fe09
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/22982
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This change adds _PRW property to CREC device that allows Linux kernel
to identify CREC as a wakeup source.
BUG=b:69118395
TEST=Verified following steps:
1. Under sys devices for CREC: "echo enabled > wakeup"
2. Lid close/Lid open -- Verified that wakeup_count increases
3. Mode change -- Verified that wakeup_count increases
Change-Id: Ib0a687e171c7e5c81325b39f47c9a2462553fe3e
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/23399
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Fix the values that were off by one.
This was discovered when using postcar stage that prints with
debuglevel BIOS_NEVER.
Change-Id: I73a077950ed0dc735d89c9747a8da0a25f30822d
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/23186
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
The `lint-extended-015-final-newlines` script skips over executable
files and thus leaves script files unchecked.
Use `file` to find scripts and include them in the `final newlines`
checks. Whitelisting is used including bash, perl, python and sh
scripts.
Change-Id: I8649b261b7e2cbbac7f9b90a9ace3f1c7b0eedeb
Signed-off-by: Alex Thiessen <alex.thiessen.de+coreboot@gmail.com>
Reviewed-on: https://review.coreboot.org/23325
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
According to SMBIOS Reference Specification (1)
section 7.18.5 Memory Device — Extended Size
When the size cannot be represented in the size field, it must be set to
0x7fff and the real size stored in the extended_size field.
1: https://www.dmtf.org/sites/default/files/standards/documents/DSP0134_3.1.1.pdf
Change-Id: Idc559454c16ccd685aaaed0d60f1af69b634ea2e
Signed-off-by: Julien Viard de Galbert <jviarddegalbert@online.net>
Reviewed-on: https://review.coreboot.org/23396
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
This change configures unused pins as not connected.
Change-Id: I6779d9fba73da8fb2faa08ad5d2236b813105720
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/23416
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change updates the camera power enable GPIOs as per the latest
schematics. With this update, since one of the enable GPIOs is using a
UART0 pin, set UART0 to PchSerialIoSkipInit in devicetree so that
FSP-S does not re-configure the UART0 GPIOs.
BUG=b:68964831
Change-Id: I5d9126ed8ca2b714f6276f4d3a24c243d7654774
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/23414
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Configure GPP_H12 as an input for PCH_WP_OD.
BUG=b:72202352
BRANCH=none
TEST=none
Change-Id: Ie5b60644a24d745add4d0d38c1421974b8a0017b
Signed-off-by: Nick Vaccaro <nvaccaro@chromium.org>
Reviewed-on: https://review.coreboot.org/23389
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
The following two patches were independent, but they were
merged together. However, the first one changed the API
that the second was originally was written against. Fix build.
b94a2750 (i2c/designware: reduce API complication for bus config)
13101a7b (soc/amd/stoneyridge: Add I2C devicetree support)
BUG=b:72121803
Change-Id: I3678a8f414572dd2227c42ce5585daf6bc933df5
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/23445
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Make is so that a different timer source can be provided instead
of TSC on x86 platforms.
BUG=b:72378235,b:72170796
Change-Id: I6faeecf7624a5aa4e1af8862036f1fbd2f54eb51
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/23435
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
The TSC rate is empirically swinging during early boot. That
leaves timestamps and udelay()s to not be correct. To rectify this
stop using TSC for all of these time sources. Instead use the
performance TSC which is at a fixed 100MHz clock. That provides
stable time sources and legit timestamps.
BUG=b:72378235,b:72170796
Change-Id: Ia2693c415c557aac687bcb48ee69358ea1c53d67
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/23424
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Some x86 platforms don't have a TSC that is invariant w.r.t.
rate to get accurate timestamps. As such a different timestamp
is required. Therefore, allow one to specify non-TSC timestamp
source and not compile in the default x86 TSC code.
BUG=b:72378235,b:72170796
Change-Id: I737fcbba60665b3bc2b5864269536fda78b44d90
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/23423
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
|
|
If GENERIC_UDELAY is selected don't try to use UDELAY_IO as there
will be a udelay() conflict at link time.
BUG=b:72378235,b:72170796
Change-Id: I9e01c9daddd0629ecc38a809889b39a505c0e203
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/23422
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
In order to fully utilize GENERIC_UDELAY in smm and postcar
the udelay() implementation needs to be included. Do that.
BUG=b:72378235,b:72170796
Change-Id: Ia20c1ed41ee439bb079e00fb7bd9c1855e31e349
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/23421
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Right now dw_i2c_get_soc_cfg() is expecting the SoC to implement
that callback for obtaining the bus config. However, we're currently
forcing another parameter of struct device so one can do the lookup.
This works for Intel-based systems since the struct device was needed
to program the BAR, etc. However, from an API standpoint, it just
complicates matters by needing to obtain the struct device. The SoC
already has knowlege of its own devices so it can get the config
itself by bus number. Therefore, remove that contraint from the API.
BUG=b:70232394
Change-Id: Id8558f5deedda0963a46a532a7bf984e168fb270
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/23420
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This commit adds support for an Elan touchscreen device connected over
I2C via devicetree.
BUG=b:72121803
TEST=Confirm the device is probed for.
Change-Id: Ia9e427dbeab9088f77e3cd751b561f7b9a8cb400
Signed-off-by: Justin TerAvest <teravest@chromium.org>
Reviewed-on: https://review.coreboot.org/23408
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
I2C bus configuration is generally set up in devicetree.cb. This change
establishes listings for the buses so that they can be used (though
followup changes should update the buses to have correct timings).
BUG=b:72121803
Change-Id: I2b12c82d2bab42ab470aa207880be8876e7cb75f
Signed-off-by: Justin TerAvest <teravest@chromium.org>
Reviewed-on: https://review.coreboot.org/23407
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This is required to add support for I2C devices on Kahlee to ACPI tables
via devicetree.cb. Without this, operations are not emitted for I2C
devices and the proper ACPI table entries are not generated.
BUG=b:72121803
Change-Id: I1cfe12f3cc23e90ec74b739678f5a5a73257c2c2
Signed-off-by: Justin TerAvest <teravest@chromium.org>
Reviewed-on: https://review.coreboot.org/23406
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
This commit establishes the stoneyridge implementation for i2c entries
in the devicetree.cb file.
BUG=b:72121803
Change-Id: I0d923609bd8fce94c9aee401a5ae2811281b60e5
Signed-off-by: Justin TerAvest <teravest@chromium.org>
Reviewed-on: https://review.coreboot.org/23405
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This commit adds device name to ACPI name bindings for various entries
in the devicetree.
BUG=b:72121803
Change-Id: I5564e4a7e56fdd1bc9f34497bdb78383093a2ba3
Signed-off-by: Justin TerAvest <teravest@chromium.org>
Reviewed-on: https://review.coreboot.org/23417
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Chrome OS reports that "GRUNT TEST XXXX" is an invalid hwid. The 8296
comes from the lower four numbers from running:
$ printf "%d\n" 0x$(crc32 <(echo -n 'GRUNT TEST'))
BUG=b:72436450
Change-Id: Ib0044442396cad65c25c107feb35a30a2f70b769
Signed-off-by: Justin TerAvest <teravest@chromium.org>
Reviewed-on: https://review.coreboot.org/23411
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Add support for a mmio resource in the devicetree to allow
memory-mapped IO addresses to be assigned to given values.
AMD platforms perform a significant amount of configuration through
these MMIO addresses, including I2C bus configuration.
BUG=b:72121803
Change-Id: I5608721c22c1b229f527815b5f17fff3a080c3c8
Signed-off-by: Justin TerAvest <teravest@chromium.org>
Reviewed-on: https://review.coreboot.org/23319
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
3rdparty/blobs was updated to move northbridge/amd/00670F00 contents into
soc/amd/stoneyridge. Now soc/amd/stoneyridge/Kconfig needs to be updated
to use VBIOS.bin new location.
BUG=b:70785272
TEST=Update 3rdparty/blobs master branch, try to build kahlee. It should
fail. Update soc/amd/stoneyridge/Kconfig, try to build kahlee again, it
should work (need to rebuild .config first).
CQ-DEPEND=CL:881709
Change-Id: I8cb9874eedc4a5d41d42b3f727c6d3cb9b920b5a
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/23398
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
Rename the device ID macros as per the skylake PCH H external design
specification.
Change-Id: I4e80d41380dc1973d02bc69ac32aad5c4741a976
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Reviewed-on: https://review.coreboot.org/23381
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This change disables SATA controller in order to make SATA IP enter
low power status.
BUG=b:72332817
TEST=cat /sys/kernel/debug/pmc_core/pch_ip_power_gating_status
and verify SATA IP enters low power state
Change-Id: I72a98bc3d0b47aebc0d7be534f4a7503084b257f
Signed-off-by: Kane Chen <kane.chen@intel.com>
Reviewed-on: https://review.coreboot.org/23354
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add config option SOC_ESPI in glkrvp Kconfig. This is to disable LPC
and enable eSPI instead.
TEST=Boot to OS
Change-Id: I3116b656d41d1d7719c254888d1e3640628a97ca
Signed-off-by: Shaunak Saha <shaunak.saha@intel.com>
Reviewed-on: https://review.coreboot.org/22626
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hannah Williams <hannah.williams@intel.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
|
|
This moves the call to pch_enable_lpc() from romstage to bootblock.
In other words, it happens earlier in the boot process. Turns out, we
need this to talk to the EC to determine if we're in recovery mode or
not.
BUG=b:69011806
TEST=boots to linux
Change-Id: I899bf343d705fe19a2978917bc88990495ebb5a3
Signed-off-by: Caveh Jalali <caveh@google.com>
Reviewed-on: https://review.coreboot.org/23401
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This adds coreboot device tree entries on zoombini & meowth for the
cr50. Also, fixes the GPIO pin IRQ settings to be falling edge. This
is based on what we do for fizz.
BUG=b:71722449
TEST=booted to linux on meowth: tpm_version command now sees the cr50.
localhost ~ # tpm_version
TPM 2.0 Version Info:
Chip Version: 2.0.0.0
Spec Family: 322e3000
Spec Family String: 2.0
Spec Level: 0
Spec Revision: 116
Manufacturer Info: 43524f53
Manufacturer String: CROS
Vendor ID: xCG fTPM
TPM Model: 00000001
Firmware Version: 0ad551830bcf7a82
localhost ~ # uname -a
Linux localhost 4.14.13 #3 SMP PREEMPT Sat Jan 13 02:55:45 PST 2018 x86_64 Genuine Intel(R) CPU 0000 @ 1.00GHz GenuineIntel GNU/Linux
localhost ~ #
and we see interrupts when talking to the cr50:
localhost ~ # grep cr50 /proc/interrupts ; tpm_version ; grep cr50 /proc/interru
pts
84: 4687 IO-APIC 84-edge cr50_spi
TPM 2.0 Version Info:
Chip Version: 2.0.0.0
Spec Family: 322e3000
Spec Family String: 2.0
Spec Level: 0
Spec Revision: 116
Manufacturer Info: 43524f53
Manufacturer String: CROS
Vendor ID: xCG fTPM
TPM Model: 00000001
Firmware Version: 0ad551830bcf7a82
84: 4799 IO-APIC 84-edge cr50_spi
localhost ~ #
Change-Id: I9d503334502503ef49515e4a8736d967bc454a98
Signed-off-by: Caveh Jalali <caveh@google.com>
Reviewed-on: https://review.coreboot.org/23310
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
|
|
BUG=b:71839089
TEST=
1. emerge-nami coreboot chromeos-bootimage
2. powerd_dbus_suspend
3. touch touchpad to wakeup system
4. localhost ~ # cat /var/log/eventlog.txt
| 2018-01-21 17:01:59 | S0ix Enter
| 2018-01-21 17:02:04 | S0ix Exit
| 2018-01-21 17:02:04 | Wake Source | GPIO | 80
Change-Id: Ie550cfa3f7b5fd105f89c16076d428743392d0e4
Signed-off-by: Van Chen <van_chen@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/23363
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The FSP 2.0 Memory_Info_HOB for KBL is not sending
"MemoryType" value as what is required for SMBIOS Table
according to SMBIOS Spec. Thus, converting the value
retrieved from FSP HOB to the correct value.
This change will not be required for upcoming SOCs since
FSP have fixed this issue in its next platforms and thus it
will take care and send the correct value in "MemoryType"
field based on SMBIOS spec. Thus this conversion from coreboot
will not be required in the next platfoms. "MemoryType" value
can be directly passed to dimm_info_fill() function.
BUG=none
BRANCH=none
TEST=Tested in Soraka, and getting the value as 0x1D for
LPDDR3 memory. dmidecode (latest version 3.1) Command Type 17
will also show correct information. Currently, it was showing
"Unknown".
Change-Id: I75d6cca464680a88bf836e25bf5440a9cdbc738e
Signed-off-by: Barnali Sarkar <barnali.sarkar@intel.com>
Reviewed-on: https://review.coreboot.org/23384
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
In payloads/nvramcui/payload.sh line 5:
DIR=`dirname $0`
^-- SC2006: Use $(..) instead of deprecated `..`
^-- SC2086: Double quote to prevent globbing and word \
splitting.
In payloads/nvramcui/payload.sh line 6:
lpgcc -o $DIR/nvramcui.elf $DIR/nvramcui.c 2>&1 >/dev/null || exit 1
^-- SC2086: Double quote to prevent globbing and word \
splitting.
^-- SC2086: Double quote to prevent \
globbing and word splitting.
^-- SC2069: The order of \
of the 2>&1 and the \
redirect matters. The \
2>&1 has to be last.
Change-Id: Iceab2d0df49c642f54e6b911793aa1479f542644
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/23373
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
|
The CAR APIs already exist to deal with proper type useage.
Don't open code things that already exist.
BUG=b:65485690
Change-Id: I09593401513f6060a30cf5c02c94d14afbe8f4fd
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/23412
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
|
|
Clean up the extra DRIVERS_I2C_GENERIC
BUG=None
TEST=None
Change-Id: Ida32b6f99c40c022aa8548f7353abf1d60ba4ddf
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/23380
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
- The em100 project needs msitools.
- Flashrom uses rsync.
Change-Id: Ie01064adede25471a860bc22c0a59b31202b56c2
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/23369
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
|
