| Age | Commit message (Collapse) | Author |
|---|
|
A new liara specific VBIOS updating eDP power sequence is available now,
Change Kconfig to use it if board is google liara.
BUG=b:120534087
TEST=Build liara, booted, tested eDP test compliance.
Change-Id: I444cfa0bd755480e006f11c0d692b25b96129c29
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/c/30090
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
A liara specific VBIOS was released and merged to blobs. Now coreboot
need to point to the updated blob, so it can use liara specific VBIOS.
Liara Chromebook Stoney VBIOS BRT39865
BRT39865.001 12/05/18,01:13:54 CL#1716128 @ 15.49.0.18 ATOMBuild#436504
Major Changes included:
1. First Stoney VBIOS released to Liara update eDP power up sequence.
BUG=b:120534087
TEST=none
Change-Id: I3b060b1ccfb311584afd0fb66258eb7cc942408d
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/c/30089
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
Recently there has been a change to print ME version. But the stage at
which the version is printed causes the HECI device to remain in D0 state.
This in turn prevents the SoC from entering S0ix state.
This change moves printing ME version a little earlier so that the HECI
device is put into D0i3 state by FSP and the SoC can enter S0ix state
successfully.
BRANCH=octopus
BUG=b:120571529
TEST=Ensure that the ME version gets printed in BIOS logs. Ensure that
the device boots to ChromeOS. Ensure that the device enters S0ix
successfully(using suspend_stress_test -c 25).
Change-Id: I85bc45003a040c8347f929457792d78a9a077c6c
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/30074
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Use CONFIG_CPU_MAX which defaults to 1 instead of CONFIG_RISCV_HART_NUM.
The default value of CONFIG_RISCV_HART_NUM was 0 and cause a jump to address 0.
Add a die() call to fail gracefully.
Change-Id: I4e3aa09b787ae0f26a4aae375f4e5fcd745a0a1e
Signed-off-by: Philipp Hug <philipp@hug.cx>
Reviewed-on: https://review.coreboot.org/c/29993
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Xiang Wang <wxjstz@126.com>
Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
|
|
Change-Id: I5a3cb41b3a7ff2aa527cc2b40c9d7438474c2f93
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/c/30084
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Correct a build error that occurs when HUDSON_UART is selected.
Replace sizeof() of a nonexistent variable with the intended type.
This was introduced in
bd48b23 "southbridge//hudson: Get rid of void pointer math".
BUG=b:118484178
TEST=Build Bettong with Chipset/"UART controller for Kern"
Change-Id: Icc0ff9d80c3f5cab9ab837cf1cd0cd8eb0753284
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/c/30072
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
The code annotated by the comment is dealing with root port 7, so update
the comment to reflect that. It looks like the comment was copied from
the root port 3 case, but not updated.
Change-Id: I0e27e4453f4c3b2b1b9dffb0c89b71373c6b303e
Signed-off-by: Tristan Corrick <tristan@corrick.kiwi>
Reviewed-on: https://review.coreboot.org/c/30078
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Use of device_t is deprecated.
Change-Id: Ib4db9c263ff156966926f9576eed7e3cfb02e78a
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/30045
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
The code is based on autoport and that for T430s
Tested:
- CPU i5-3337U
- Slotted DIMM 2GiB
- Soldered RAM 4GiB from samsung (There may be more models here)
- Camera
- pci-e and usb2 on M.2 slot with A key for wlan
- sata and usb2 (no superspeed components) on M.2 slot with B key for wwan
- On board SDHCI connected to pci-e
- USB3 ports
- libgfxinit-based graphic init
- NVRAM options for North and South bridges
- Sound
- Thinkpad EC
- S3
- TPM1 on LPC
- EHCI debug on SSP2 (USB3 port on the left)
- Linux 4.9.110-3 within Debian GNU/Linux stable, loaded from
Linux payload (Heads), Seabios may also work.
Not tested:
- Fingerprint reader on USB2 (not present on mine)
- Keyboard backlight (not present on mine)
- "sticky_fn" flag in nvram
Not implemented yet:
- Fn locking in nvram (may not be identical to "sticky_fn")
- C-based native graphic init (since T431s has eDP instead of LVDS)
- Detecting the model of Soldered RAM at runtime, and loading the
corresponding SPD datum (3 observed) from CBFS (the mechanism may be
similar to that on x1_carbon_gen1 and s230u, but I do not know how
to find gpio ports for that, and SPD data stored in vendor firmware.)
Change-Id: Ic8062cacf5e8232405bb5757e1b1d063541f354a
Signed-off-by: Bill XIE <persmule@gmail.com>
Reviewed-on: https://review.coreboot.org/c/30021
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
Provide rise/fall times as measured on existing boards. This will
need adjusted for new boards but provides a starting point that
makes I2C clocks look reasonable.
Tested by measuring I2C bus speed and rise/fall times with a scope.
Change-Id: Ic18010f5efc41dcee8925d696767ba2c44e3df4b
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/30069
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
|
|
Add an entry to the soc_clock table for a 216MHz clock so that
the I2C controller clock is calculated correctly when the I2C
bus is used in coreboot.
This was tested by measuring the I2C clock speed on H1 I2C bus
on a sarien board in coreboot and ensuring it is ~400KHz.
Change-Id: I6c3cacdad318a5ce41bc41e3ac81385c2d4f396c
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/30068
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
The input clock for the I2C controllers was set at 133MHz but should
really be 216MHz according to the kernel:
https://patchwork.kernel.org/patch/10408729/
"Intel Cannon Lake PCH has much higher 216 MHz input clock to LPSS I2C
than Sunrisepoint which uses 120 MHz. Preliminary information was that
both share the same clock rate but actual silicon implements elevated
rate for better support for 3.4 MHz high-speed I2C."
This change was tested on a sarien board where an I2C trackpad that was
measuring ~700MHz on I2C and is now measuring ~380MHz.
Change-Id: I792d1f013da5538a2b8157e2f99b754ca7b6bf70
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/30061
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
According to issue tracker b:119899090.
https://partnerissuetracker.corp.google.com/issues/119899090
We modify rammus devicetree.cb .i2c[1] configuration to meet ELAN touchpad I2C special timing requirement.
BUG=b:119899090
BRANCH=firmware-rammus-11275.B
TEST=emerge-rammus coreboot chromeos-ec chromeos-bootimage
Flash FW to DUT, and check touchpad I2C characteristics meet requirement
Signed-off-by: YanRu chen <kane_chen@pegatron.corp-partner.google.com>
Change-Id: Ifeb08c2530e6a7674f23f7d48cefa16cfc59cb13
Reviewed-on: https://review.coreboot.org/c/29922
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
As part of the memory mapped BIOS region is covered by SRAM, check
that CBFS always fits the effectively mapped region of flash. This
is usually taken care of by reserving the SRAM range in the FMAP
(e.g. as BIOS_UNUSABLE), but can be missed.
Change-Id: If5a5b553ad4853723bf13349c809c4f6154aa5f2
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/c/30055
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
BUG=b:119799550
BRANCH=master
TEST=Verify touchscreen on sarien works with this change.
Change-Id: I926c988c141628ae2d98206f9eb615d06357a366
Signed-off-by: Chris Zhou <chris_zhou@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/29830
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
ISA timer is not configured.
Add call setup_i8254().
BUG=N/A
TEST=Intel CherryHill CRB
Change-Id: If45c4975d147f28a456198ea290efba1c8b0464b
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/29416
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
Re-write the UAO handling code as it had stopped working (#171)
(the flag was not getting read from the RTC properly in SMM)
Remove the SMM code as it's not needed (but EC flag won't be set
upon entering S3 now)
Set the EC flags on boot the same way other flags are set
Document bitwise operators for clarity
Propagate changes to other Thinkpads
(updated X201 to have 2 bits for the flag as it only had 1)
Per Nicola Corna's previous commits, 0x0d is set for "AC only"
"AC only" does exhibit different behaviour - the USB port is
turned on a few seconds after entering S3, rather than < 1 sec,
regardless of AC status
Tested on X220
Change-Id: If812cd1ef8fb1a24d7fadbe834f574b40cbcd56a
Signed-off-by: Nathaniel Roach <nroach44@gmail.com>
Reviewed-on: https://review.coreboot.org/c/29565
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
|
|
Change-Id: I41363685bb5c84ce15698f96e58f6a5da9bd2ba2
Signed-off-by: Tristan Corrick <tristan@corrick.kiwi>
Reviewed-on: https://review.coreboot.org/c/30075
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Tested - Lenovo t520 still builds fine with this patch.
Change-Id: I82492c071ca760f0790b992acbdb86021f470cfe
Signed-off-by: Peter Lemenkov <lemenkov@gmail.com>
Reviewed-on: https://review.coreboot.org/c/30043
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
Turn on the ISH in the device tree.
BUG=b:120295222
Change-Id: I0ba08c245d050aebc6eb06055690c422ab9b51c6
Signed-off-by: Jett Rink <jettrink@chromium.org>
Reviewed-on: https://review.coreboot.org/c/30034
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Required to compile the code in x86_64, even though it's never used.
Change-Id: I2be8ad8805804e4da52bdb02ab43cb833402f999
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/c/29876
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Fix some compiler warnings due to pointer to integer conversions
with different size.
Required for 64bit ramstage.
Change-Id: Ibfb3cacf25adfb4a242d38e4ea290fdc3929a684
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/c/29875
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
The gerrit docs aren't very explicit about it, but file:"^foo$" is more
robust than file:^foo$.
Change-Id: I16c7d972d365cd04ca5fbb78012ad4eaad667be6
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/29781
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
I fried my mainboard because I tried to orient my chip by lining a blue dot on
the corner of my chip with a dot depicted on the chip datasheet. They
apparently have nothing to do with each other, and this is normal. Add
warning about this to the docs to hopefully spare others from a similar fate.
Signed-off-by: Michael Bacarella <michael.bacarella@gmail.com>
Change-Id: Ib634589aaa11f75bde2ef2e13d2cacc4cae19a3f
Signed-off-by: Michael Bacarella <michael.bacarella@gmail.com>
Reviewed-on: https://review.coreboot.org/c/30028
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
|
|
TEST=build & run
Change-Id: Ie404faf37617d2ad792310709ca2063f9a372076
Signed-off-by: Mukesh Savaliya <msavaliy@codeaurora.org>
Reviewed-on: https://review.coreboot.org/c/25392
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Move the backlight initialization from bootblock to romstage
BUG=b:120436919
TEST=Careena backlight is enabled
Change-Id: Ia4993b993d37afaf9e23d6f3316ba91053732f1d
Signed-off-by: Martin Roth <martinroth@chromium.org>
Reviewed-on: https://review.coreboot.org/c/30039
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Daniel Kurtz <djkurtz@google.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
This is needed so the next patch can set up GPIOs before
AGESA runs.
BUG=b:120436919
TEST=Verified romstage mainboard code runs before AGESA
Change-Id: I76c035e166cd64382b52dff5ae00a6f115cbac9b
Signed-off-by: Martin Roth <martinroth@chromium.org>
Reviewed-on: https://review.coreboot.org/c/30038
Reviewed-by: Daniel Kurtz <djkurtz@google.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Platform have a 32MB SPI chip, so we can increase the bios region from
16MB to 28MB.
BUG=b:119267832
TEST=Build and boot fine on sarien platform.
Change-Id: I9bc0fa0f662e5ec64e77f2005dbb2e7edb8b2524
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/c/29945
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
This patch removes several timer and serial drivers (and configs) that
were specific to platforms which have been dropped in coreboot.
Change-Id: I589ca7f1a3b479f1c2b1b668a175a71583441ac9
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/30029
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
|
|
AMD traditionally claims the resource at I/O port 61 for the onboard
PC-AT speaker. In later designs, the speaker may be omitted in favor
of routing the SPKR signal to the codec.
Some systems implement neither, and for those it is not correct to
identify the resource as a speaker. Modify the EISAID reported to
the OS depending on the system design. The default is that port 61
is reported as reserved. In order to report a speaker, add #define
in mainboard//dsdt.asl.
TEST=check /proc/ioports and iasl -d for both ways using a Grunt
BUG=b:117818432
Change-Id: I33aafb187f9fea7b38aae43c399292c7521fcfc4
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/c/30037
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
|
|
When building grunt with flags set to detect variables that get a value but
then are unused, there are 5 instances that causes error (unused variable).
In most cases it's enough to simply remove the variable. Other instances,
is better to simply use the variables (one instance it's a return value, on
the other instance using the variables makes code more readable).
BUG=b:120260448
TEST=Build and boot grunt.
Change-Id: I0d00fb6a42db20afb34c76b9445a741a57096ead
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/c/29985
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Change-Id: Ifb08c903e19ef4e93bdc9cbc9844cb1888a8d2fa
Signed-off-by: Peter Lemenkov <lemenkov@gmail.com>
Reviewed-on: https://review.coreboot.org/c/29811
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Sort mainboard-specific defines in the same order as in all other Lenovo
boards. This is a purely cosmetic change which just makes diff between
boards smaller.
Change-Id: I4e379bb727b356fc6010e93de492f6d73f97a750
Signed-off-by: Peter Lemenkov <lemenkov@gmail.com>
Reviewed-on: https://review.coreboot.org/c/29544
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Most Lenovo mainboards define their own specific defines in dsdt.asl.
Let's make it consistent across all Lenovo mainboards.
Tested - builds fine.
Change-Id: I03fbeb09b25e42af2dfbb220c0f726e6abb73673
Signed-off-by: Peter Lemenkov <lemenkov@gmail.com>
Reviewed-on: https://review.coreboot.org/c/29543
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
|
|
Now that all targets featuring these southbridges use SMM_TSEG these
files are unused.
Change-Id: Ic3a1d790f3595e98a8d33e6e8274cb72ad356a89
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/30018
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
tlclk is not specific to the UART block in the FU540, so let's calculate
its frequency in clock.c.
Change-Id: I270920027f1132253e413a1bf9feb4fe279b651a
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/c/29335
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Philipp Hug <philipp@hug.cx>
|
|
This patch lets spike boot to "Payload not loaded" again.
Because soc/ucb/riscv/ does not represent a real SoC, but is a dummy
directory for emulators, and different emulators might have different
memory maps, I moved mtime_init to the mainboard-specific directories
for Spike and QEMU.
Change-Id: I080f7f81df752e25478bd277637bf894bbee4cb2
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/c/28873
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philipp Hug <philipp@hug.cx>
|
|
Init SPI bus 0 to connect TPM, configure interrupt type of GPIO CR50_IRQ,
implement tis_plat_irq_status(), and set up chromeos GPIO table for TPM
interrupt.
BUG=b:80501386
BRANCH=none
Test=Boots correctly on Kukui.
Change-Id: Ieaa6ae65fbfb5ab6323e226e8171dd7a992c3a39
Signed-off-by: Tristan Shieh <tristan.shieh@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/29192
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Refactor GPIO EINT code which can be reused among similar SoCs.
BUG=b:80501386
BRANCH=none
TEST=emerge-elm coreboot; emerge-kukui coreboot
Change-Id: Ib01b43cf1aa4082d7d968fe1ef82f75e8cf05b8b
Signed-off-by: Chuanjia Liu <Chuanjia.Liu@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/29837
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
Use common code to tear down CAR.
Change-Id: I62a70ae35fe92808f180f2b5f21c5899a96c2c16
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/29930
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Change-Id: I77e375a2ff2fbf1be4ded922195b80b49ffa4cc5
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/29929
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This patch does the following:
- improve the style by removing tabs in front of jmp addresses
- Make the code for zeroing variable MTRR more readable (copied from
cpu/intel/car)
- Fetch PHYSMASK high from cpuid instead of Kconfig
Change-Id: I6ba67bb8b049c3f25b856f6ebb1399d275764f54
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/29928
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
This does the following:
- Reuse the cpu/intel/car/non-evict CAR setup and exit.
- Use postcar_frame functions to set up the postcar frame
Change-Id: I428832a2d7e46ce61a7f9bd498b609feb4518eb0
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/29927
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Instead of SMMSTORE_APM_CNT use APM_CNT_SMMSTORE and define it in
cpu/x86/smm.h
Change-Id: Iabc0c9662284ed3ac2933001e64524011a5bf420
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/30023
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Instead of ELOG_GSMI_APM_CNT use APM_CNT_ELOG_GSMI and define it in
cpu/x86/smm.h
Change-Id: I3a3e2f823c91b475d1e15b8c20e9cf5f3fd9de83
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/30022
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Use a raw fmap region SMMSTORE for the SMMSTORE mechanism, while
keeping the initial option to use a cbfsfile.
TESTED on Asus P5QC, (although it looks like the tianocore patches
using it might need some love as they can't seem to save properly).
Change-Id: I8c2b9b3a0ed16b2d37e6a97e33c671fb54df8de0
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/29991
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
|
|
Needed to fix up FSP-S bug on Apollo Lake.
Change-Id: If09fee07debb1f0de840b0c0bd7a65d338665f7c
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/c/29898
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
We alwas define uint64_t as unsigned long long, even on x86_64.
Fix PRIu64 to match the definition of the datatype, to prevent
compilation errors when compiling for x86_64.
Change-Id: I7b10a18eab492f02d39fc2074b47f5fdc7209f3d
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/c/30002
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
|
|
Provide pic of the flash IC with pinouts labeled, as well
as additional text about the chip.
Signed-off-by: Michael Bacarella <michael.bacarella@gmail.com>
Change-Id: I9046fa63dcd4d192836417efac68ca7587ac1c91
Signed-off-by: Michael Bacarella <michael.bacarella@gmail.com>
Reviewed-on: https://review.coreboot.org/c/30027
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
Set GPIO D22 low to get WWAN_PERST#_R asserted.
BUG=N/A
TEST=Boot up with Arcada board, check WWAN get detected as USB devices
through lsusb command.
Change-Id: Ie848cd19fdf3b6c4b6abeb5fa3f566e5e4e7e928
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/c/30030
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Bora Guvendik <bora.guvendik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Cache BIOS region can boost boot performance, however it can't be over
16MB, according to processor EDS vol1(Apollolake/Skylake/WhiskeyLake),
FLASH+APIC LT will be less than 20MB under 4G. Set the maxiam to 16GB
to save numbers of mtrr entries.
BUG=b:119267832
TEST=Build and boot up fine on whiskeylake rvp platform.
Change-Id: I46a47c8bf66b14fb2fcb7b6b1d30d02886c450a4
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/c/29944
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
BUG=b:111812662
TEST=flash to nocturne, boot nocturne, run "memtester 1g" and
verify it passes.
Change-Id: Iefc3957f915a39a47ad6018459e65b70d1b34091
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/29361
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Add the USB device information for the sarien/arcada variants.
This includes the ACPI _PLD group definitions for the external
ports that indicate which USB2 and USB3 ports share the same
physical interface.
Change-Id: I0b936127954ba09c61ccb871bfc62ee7d99da263
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/30000
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Add ACPI _PLD group definitions for the external ports
that indicate which USB2 and USB3 ports share the same
physical interface.
Change-Id: I7f85720a878a3774d453a9adb82518722f7ba23d
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/29999
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
The Linux kernel can use the ACPI _PLD group information to
determine peer ports. Currently to define the group information
the devicetree must provide a complete _PLD structure. This
change pulls the group information into a separate structure that
can be defined in devicetree. This makes it easier to set for
USB devices in devicetree that do not need a full custom PLD.
This was tested on a sarien board with the USB devices defined
by verifying that the USB 2/3 ports are correctly identified
with their peer in sysfs.
Change-Id: Ifd4cadf0f6c901eb3832ad4e1395904f99c2f5a0
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/29998
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Add the ACPI device names for the USB ports to match what
is in the DSDT so USB ports can be defined in the SSDT.
Change-Id: Ibb323bbd324811fa3178b0cba3d7f0a315169486
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/29997
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Increase the bootblock size to 48K to match skylake. With UART
enabled we are very near the 32K limit, and with upcoming changes
to add USB devices in devicetree for a cannonlake board it is over
the current 32K limit.
Change-Id: I155cb0a6af1746af6833fa9f35c2ea6fe0bc709f
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/29996
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Send the EC command required to turn the camera power on
and verify that it shows up on the USB bus.
Change-Id: I9e9ba712a11cef85cde91ac21a4b6b5090ef58dc
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/29987
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Enable DPTF support for sarien/arcada boards. This is currently
using placeholder values that are identical that will be updated
after thermal tuning is done.
Change-Id: I7d51c3b38068fc25927c8dafc0bd9069b29d77f5
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/29762
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
There is a dependency issue with the EC DPTF code accessing
methods that are external, but once the mainboard includes the
relevant code they become internal and the current version of
IASL used by jenkins will fail to compile it.
Until the new IASL is deployed everywhere wrap the EC DPTF code
and expect that the mainboard will explicitly enable it.
Change-Id: I612ad8f86d424060ca0303d267d7c2915c760173
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/30036
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Add the support needed for DPTF. This includes the methods to
write trip point values, read temperatures, and handle events.
This was tested on a sarien board by inspecting AML debug output
with the kernel while monitoring temperatures and trip points in
sysfs and controlling temperatures with a fan to ensure that when
a trip point is crossed an SCI is generated and the event is
handled properly.
Change-Id: I8d8570d176c0896fa709a6c782b319f58d3c1e52
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/29761
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The user needs to pass the original firmware image to create
a layout file, not the newly compiled coreboot image.
Signed-off-by: Michael Bacarella <michael.bacarella@gmail.com>
Change-Id: If47a88f06076da12d8da7a873c3e5ef64fc1f877
Reviewed-on: https://review.coreboot.org/c/30024
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Documentation that was there seems to reference and older version.
Signed-off-by: Michael Bacarella <michael.bacarella@gmail.com>
Change-Id: I3709613ae065153123d00801ea1b4ff86b100264
Reviewed-on: https://review.coreboot.org/c/30025
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Signed-off-by: Michael Bacarella <michael.bacarella@gmail.com>
Change-Id: I781e2d78c0525da74dd77f572839d746d3eeb3ce
Signed-off-by: Michael Bacarella <michael.bacarella@gmail.com>
Reviewed-on: https://review.coreboot.org/c/30026
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
- Disable debug output from read/write methods by default
- Use argument to _REG to disable SCI when EC is unregistered
- Change read/write macros to sync level 2 so they can be called
when a mutex is already held
- Define some missing events
Change-Id: Ic65ebbb6a6151444c47b4aeff7429e186856c49a
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/29760
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Define the constants that DPTF expects from the SOC in order to
use the common DPTF ACPI code. For cannonlake this indicates
the CPU device is called B0D4 and is at PCI address 00:04.0.
Change-Id: I43c2f8dd7281d3e9f791ab01478ee7823fd6b128
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/29759
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add a method to convert from 1/10 Kelvin to Celsius. This
is useful for EC devices where the sensor temperature are
stored in Celsius instead of Kelvin.
Change-Id: I6b1154f5ba13416131a029966d6d5c1598904881
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/29758
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
In order to support using the common ACPI code on more platforms
than just Apollo Lake the DPTF code needs to be told what the
PCI address is for the CPU thermal device.
Change-Id: I638f2387330bbc42f64eb0fb676ee32c5df6572e
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/29757
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Extended events will be handled by the OS kernel driver, but that
driver needs a method exposed by ACPI to read the event data from
the EC and into a buffer.
Tested by generating a hotkey event and reading the buffer from
the Linux kernel driver with acpi_evaluate_object().
Change-Id: Ic8510e38d777a5dd31a5237867313efefeb2b48e
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/29674
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add EC command to enable WiFi radio and send that command at
startup. Tested to ensure WiFi is functional on a sarien board.
Change-Id: Iac46895c7118567e1eb55ea33051a1662103b563
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/29673
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Enable the COM1 ACPI device based on the existing Kconfig option
CONFIG_DRIVERS_UART_8250IO instead of expecting the mainboard to
also define another value for ACPI.
Change-Id: I69361cc2c245cfcad3e4f57567bf56d5a26f0b06
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/29672
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Set WWAN_GPIO_PERST#(GPP_D22) to low at bootblock stage to meet
the logic output for WWAN_PERST#_R to high.
BUG=120004153
TEST=Boot up Sarien board, check WWAN get detected as USB
devices through lsusb.
Change-Id: I16f1101c64dfd4dcb5e8342fdb925951f6f2f90b
Signed-off-by: Amanda Huang <amanda_hwang@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/30017
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
The different PLLs in the fu540 use the same register layout, so use one
function (configure_pll) to program a PLL and wait for it to lock. This
also makes it possible to dynamically calculate the PLL settings later.
TEST=Boot until "Payload not loaded" on HiFive Unleashed
Change-Id: I5c0cee886bad5758c70f967d2bb998c1e1a736ab
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/c/29356
Reviewed-by: Philipp Hug <philipp@hug.cx>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Correct typo of 'Initialize'
BUG=N/A
TEST=N/A
Change-Id: I94cfd9c41bb5f9751ef4a18beaeba05108220bc8
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/30016
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
* Verify the flash write protection on each boot
* Program non-volatile write protection on first boot
Tested using I715791b8ae5d1db1ef587321ae5c9daa10eb7dbc.
The bootblock is write-protected as long as the #WP pin is asserted low:
* Reprogramming of the status register fails.
* Trying to write to WP_RO region fails.
Programming the WP_RO is only possible if #WP pin is high.
Change-Id: I6a940c69ecb1dfd9704b2101c263570bebc5540e
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/29532
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
|
|
The TB has to be inverted to actually protected the correct region.
Tested on elgon using I67eb4ee8e0ad297a8d1984d55102146688c291fc.
Change-Id: I715791b8ae5d1db1ef587321ae5c9daa10eb7dbc
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/30014
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
Reviewed-by: Julius Werner <jwerner@chromium.org>
|
|
update the new sku ids of bard/ekko
BUG=b:120257865
BRANCH=Nami
TEST=emerge-nami coreboot chromeos-bootimage
write the new sku id in cbi and verify the fw to
check it can get the correct settings by the sku id
Change-Id: I3579d3d8042a270d8ea8e2f7b5612ff8e2cdfa7b
Signed-off-by: Ren Kuo <ren.kuo@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/30031
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This change enables mode change as a wake source from S3 and
S0ix. Thus, any time the device switches between clamshell and tablet
mode while it is suspended, it will be treated as a valid user event
and hence wake source.
BUG=b:120349473
BRANCH=octopus
TEST=Verified that octopus wakes up on mode transitions.
Change-Id: Ib224df434730f873ce5514303e5d043cbc85a9a4
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/30001
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
|
|
Backlight control of internal panels likely won't work as configuration
for that seems absent in coreboot. Also, libgfxinit doesn't support any
MIPI/DSI connections, yet, and neither Gemini Lake.
TEST=Booted work-in-progress port kontron/mal10 with VGA text and
linear framebuffer modes. DP display came up.
Change-Id: I7b111f1cdac4d18f2fc3089f57aebf3ad1739e5d
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/c/29903
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
The referenced Kconfig symbols don't exist (anymore?).
Change-Id: Ia724262a526fe960c17ae4b248acfa42fc342331
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/c/29931
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: David Guckian
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
Removes a warning in Linux about FACP.
Change-Id: Ia12302a4dcd34eacdcc8ae16bd39e951e616c6ea
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/30011
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
This change adds support to print ME version if UART_DEBUG is
enabled. Check for UART_DEBUG is necessary because talking to ME to
get the firmware version adds ~0.6 seconds to boot time.
TEST=Verified on octopus that ME version printed is correct.
Change-Id: I41217371558da1af694a2705e005429155d62838
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/29989
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Rename "smm store" to "smm_store".
BUG=b:120060878
TEST=None
Signed-off-by: Joel Kitching <kitching@google.com>
Change-Id: If70772e17cc1668a28b376eeccfde0424e637b1a
Reviewed-on: https://review.coreboot.org/c/29854
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Replace IO access to ACPI registers with the new MMIO access functions.
BUG=b:118049037
TEST=Build and boot grunt. Test ACPI related functionality.
Change-Id: I7544169bb21982fcf7b1c07ab7c19c6f5e65ad56
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/c/29296
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
ACPI registers can be accessed through IO or through MMIO. However, the
offset relationship is not one to one. Therefore, definitions with the
correct offset for MMIO access are needed.
BUG=b:118049037
TEST=Use Chrome OS IOTOOLS io_readxx and mem_readxx to find the correct
relationship between ACPI IO and ACPI MMIO.
Change-Id: Id20754c0fc0af35bc9eb1a4b40c62fbf9ed6304d
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/c/29294
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
|
This makes the mainboard able to boot again.
Change-Id: Id96fbfd5c815431dba2f030fca62a5ea16b97393
Signed-off-by: Kevin Cody-Little <kcodyjr@gmail.com>
Reviewed-on: https://review.coreboot.org/c/29994
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
Add myself as a maintainer of the four mainboards I ported. For those
which were added as a variant, add myself as a maintainer of the whole
mainboard group.
Change-Id: I0e1b54279027fae82ea9f2825e6f27d38ef3c746
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/29995
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
"if" is preferable over "#if", because it lets the compiler perform
syntax and type checks even if CONFIG_CONSOLE_SERIAL is disabled.
Change-Id: I45a763f2d854fbe9082795bc74de7a9d0fded3c9
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/c/29336
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philipp Hug <philipp@hug.cx>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
|
|
clock_get_coreclk_khz() already detects whether the PLL or the input
clock (hfclk) is used.
Tested on HiFive Unleashed.
Change-Id: I264977b0de0b81ef74a014984b6d33638ab33f4b
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/c/29334
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philipp Hug <philipp@hug.cx>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
|
|
Philipp has been reviewing and writing RISC-V-related code for a while.
Change-Id: I3f2d3a61f66343a6e0350909edfe466d2ee6c089
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/c/29980
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Reviewed-by: Philipp Hug <philipp@hug.cx>
|
|
All Lynx Point board select this, and none build without it.
Change-Id: I4b59b10ee985cff5a8e1442677d36b0be88cf437
Signed-off-by: Tristan Corrick <tristan@corrick.kiwi>
Reviewed-on: https://review.coreboot.org/c/29992
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
The common finalise code is used by bd82x6x, Lynx Point, and Ibex Peak.
Lynx Point now benefits from being able to write-protect the flash chip.
For Lynx Point, writing the SPI OPMENU now happens in ramstage, as done
in bd82x6x.
Tested on an ASRock H81M-HDS (Lynx Point). When write-protection is
configured, flashrom reports all flash regions as read-only, and does
not manage to alter the contents of the flash chip.
Also tested on an ASUS P8H61-M LX (Cougar Point). Everything seems to
work as before.
Change-Id: I781082b1ed507b00815d1e85aec3e56ae5a4bef2
Signed-off-by: Tristan Corrick <tristan@corrick.kiwi>
Reviewed-on: https://review.coreboot.org/c/29977
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
The finalise handler is not called during S3 resume when using the
`BS_PAYLOAD_BOOT` approach. So, adopt the `lpc_final` approach used by
bd82x6x and others.
Tested on an ASRock H81M-HDS. The finalise handler is now called on
the normal boot path, and during S3 resume.
Change-Id: I9766a8dcbcb38420e937c810d252fef071851e92
Signed-off-by: Tristan Corrick <tristan@corrick.kiwi>
Reviewed-on: https://review.coreboot.org/c/29976
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
The ASRock H81M-HDS doesn't implement a finalise handler. To fix
this, and reduce code duplication in the process, make a common
implementation. There should be no functional change to boards with
existing finalise handlers, since the code is identical among them and
the new, common implementation.
Tested on an ASRock H81M-HDS. The finalise handler works.
Change-Id: I13b581a2219288019a4e0c9e618db3ac7c3c15ab
Signed-off-by: Tristan Corrick <tristan@corrick.kiwi>
Reviewed-on: https://review.coreboot.org/c/29975
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
|
|
The WACOM 5C01 touch panel power-up delay of 10mS is too aggressive
and causes "failed to change power setting" errors in the kernel, so
this change increases the power-up delay to 20mS which allows enough
time for the WACOM device's i2c controller to wake up.
BUG=b:120090384
BRANCH=none
TEST=flash and boot nocturne, log into kernel, execute the following
command and make sure the string is not found :
dmesg | grep "failed to change power setting"
Change-Id: I1db0b3f5ce666b79d8ada2939ec865233ce52a56
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/29988
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
We discovered that the gpios previously used for FPMCU_INT_L were in
two different groups with two different voltages (C group was at 3.3V
and D group was at 1.8V). Moving both to B group which is at 3.3V.
BUG=b:119447525
BRANCH=Nami
TEST=unlock OS with fingerprint
register fingerprint
run powerd_dbus_suspend and see if it goes int s0ix
Change-Id: I2332b0eb7a2f74e8178b95a23c8ac2091027a071
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/29872
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Ren Kuo <ren.kuo@quanta.corp-partner.google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Update USB port info according to the schematic file.
BUG=none
BRANCH=master
TEST=Compiles successfully and boot on DUT.
Change-Id: I7383b3d676fd7c775a6d749c70af65b28cf941eb
Signed-off-by: David Wu <David_Wu@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/29912
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
This change selects Kconfig option to disable native SD card
controller in ACPI tables.
BUG=b:119798840
BRANCH=master
TEST=Compiles successfully and boot on DUT.
Change-Id: I68dc9be511a370d882e4656c165efbe5dc6ee52e
Signed-off-by: David Wu <David_Wu@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/29918
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
|
|
Make build still pass in case of no FsptUpd.h available.
BUG=N/A
TEST=Delete FsptUpd.h and build pass wihtout FSP_CAR set.
Change-Id: I3936d3deb8b079bd4db11e444f6bb7f9605520dc
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/c/29907
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
|
|
Now that the relationship between IO access and MMIO access has been
established, create read/write functions to access ACPI standard registers
through MMIO.
BUG=b:118049037
TEST=Build grunt
Change-Id: I32c26f342885c0d99b082be98730edcf16ab5dfc
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/c/29295
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
|
