diff options
Diffstat (limited to 'targets/tyan/s2875')
| -rw-r--r-- | targets/tyan/s2875/Config.lb | 253 |
1 files changed, 22 insertions, 231 deletions
diff --git a/targets/tyan/s2875/Config.lb b/targets/tyan/s2875/Config.lb index 42a0b99b50..cb4138064e 100644 --- a/targets/tyan/s2875/Config.lb +++ b/targets/tyan/s2875/Config.lb @@ -2,251 +2,42 @@ # the Tyan s2875 # This will make a target directory of ./s2875 -loadoptions - target s2875 +mainboard tyan/s2875 -uses ARCH -uses CONFIG_COMPRESS -uses CONFIG_IOAPIC -uses CONFIG_ROM_STREAM -uses CONFIG_ROM_STREAM_START -uses CONFIG_SMP -uses CONFIG_UDELAY_TSC -uses CPU_FIXUP -uses FALLBACK_SIZE -uses HAVE_FALLBACK_BOOT -uses HAVE_MP_TABLE -uses HAVE_PIRQ_TABLE -uses i586 -uses i686 -uses INTEL_PPRO_MTRR -uses HEAP_SIZE -uses IRQ_SLOT_COUNT -uses k7 -uses k8 -uses MAINBOARD -uses MAINBOARD_PART_NUMBER -uses MAINBOARD_VENDOR -#uses MEMORY_HOLE -uses PAYLOAD_SIZE -uses _RAMBASE -uses _ROMBASE -uses ROM_IMAGE_SIZE -uses ROM_SECTION_OFFSET -uses ROM_SECTION_SIZE -uses ROM_SIZE -uses STACK_SIZE -uses USE_FALLBACK_IMAGE -uses USE_OPTION_TABLE -uses HAVE_OPTION_TABLE -uses CONFIG_CHIP_CONFIGURE - -#uses CONFIG_CONSOLE_BTEXT -uses CONFIG_CONSOLE_SERIAL8250 -uses TTYS0_BAUD -uses DEFAULT_CONSOLE_LOGLEVEL -uses MAXIMUM_CONSOLE_LOGLEVEL -uses DEBUG -uses CONFIG_MAX_CPUS -uses CONFIG_LOGICAL_CPUS -uses CONFIG_MAX_PHYSICAL_CPUS -uses LINUXBIOS_EXTRA_VERSION -uses XIP_ROM_SIZE -uses XIP_ROM_BASE -uses HAVE_HARD_RESET - -#uses CONFIG_VGABIOS -#uses CONFIG_REALMODE_IDT -#uses CONFIG_PCIBIOS -#uses VGABIOS_START -#uses SCSIFW_START - -# -#uses CONFIG_LSI_SCSI_FW_FIXUP - -option HAVE_OPTION_TABLE=1 -option HAVE_MP_TABLE=1 -option CPU_FIXUP=1 -option CONFIG_UDELAY_TSC=0 -option i686=1 -option i586=1 -option INTEL_PPRO_MTRR=1 -option k7=1 -option k8=1 -option ROM_SIZE=524288 - -#option CONFIG_CONSOLE_BTEXT=1 -#option CONFIG_VGABIOS=1 -#option CONFIG_REALMODE_IDT=1 -#option CONFIG_PCIBIOS=1 -#option VGABIOS_START=1 -#option SCSIFW_START=0xfff80000 - - -option HAVE_FALLBACK_BOOT=1 - -# use the new chip configure code. - -option CONFIG_CHIP_CONFIGURE=1 -#option CONFIG_LSI_SCSI_FW_FIXUP=1 - - -option HAVE_HARD_RESET=1 - -### -### Build code to export a programmable irq routing table -### -option HAVE_PIRQ_TABLE=1 -option IRQ_SLOT_COUNT=13 -# -### -### Build code for SMP support -### Only worry about 2 micro processors -### -option CONFIG_SMP=1 -option CONFIG_MAX_CPUS=2 -option CONFIG_LOGICAL_CPUS=0 -option CONFIG_MAX_PHYSICAL_CPUS=2 -# -### -### Build code to setup a generic IOAPIC -### -option CONFIG_IOAPIC=1 -# -### -### MEMORY_HOLE instructs earlymtrr.inc to -### enable caching from 0-640KB and to disable -### caching from 640KB-1MB using fixed MTRRs -### -### Enabling this option breaks SMP because secondary -### CPU identification depends on only variable MTRRs -### being enabled. -### -#option MEMORY_HOLE=0 -# -### -### Clean up the motherboard id strings -### -option MAINBOARD_PART_NUMBER="S2875" -option MAINBOARD_VENDOR="Tyan" -# -### -### Compute the location and size of where this firmware image -### (linuxBIOS plus bootloader) will live in the boot rom chip. -### -#option FALLBACK_SIZE=524288 -#option FALLBACK_SIZE=98304 -option FALLBACK_SIZE=131072 - -## ROM_IMAGE_SIZE is the amount of space to allow linuxBIOS to occupy. -option ROM_IMAGE_SIZE=65536 - - -### -### Compute where this copy of linuxBIOS will start in the boot rom -### -# -### - -## We do use compressed image -option CONFIG_COMPRESS=1 - -option CONFIG_CONSOLE_SERIAL8250=1 -option TTYS0_BAUD=115200 - -## -### Select the linuxBIOS loglevel -## -## EMERG 1 system is unusable -## ALERT 2 action must be taken immediately -## CRIT 3 critical conditions -## ERR 4 error conditions -## WARNING 5 warning conditions -## NOTICE 6 normal but significant condition -## INFO 7 informational -## DEBUG 8 debug-level messages -## SPEW 9 Way too many details - -## Request this level of debugging output -option DEFAULT_CONSOLE_LOGLEVEL=8 -## At a maximum only compile in this level of debugging -option MAXIMUM_CONSOLE_LOGLEVEL=8 - -option DEBUG=1 - -# - -## LinuxBIOS C code runs at this location in RAM -option _RAMBASE=0x004000 - -## -## Use a 32K stack -## -option STACK_SIZE=0x8000 - -## -## Use a 56K heap -## -option HEAP_SIZE=0xe000 - -# -### -### Compute the start location and size size of -### The linuxBIOS bootloader. -### -option CONFIG_ROM_STREAM = 1 - -# -# +# Tyan s2895 romimage "normal" -# 48K for SCSI FW +# 48K for SCSI FW # option ROM_SIZE = 475136 -# 48K for SCSI FW and 48K for ATI ROM -# option ROM_SIZE = 425984 - option LINUXBIOS_EXTRA_VERSION="$(shell cat ../../VERSION)_Normal" - option USE_FALLBACK_IMAGE=0 - option ROM_SECTION_SIZE = (ROM_SIZE - FALLBACK_SIZE) - option ROM_SECTION_OFFSET= 0 - - option PAYLOAD_SIZE = (ROM_SECTION_SIZE - ROM_IMAGE_SIZE) - option CONFIG_ROM_STREAM_START = (0xffffffff - ROM_SIZE + ROM_SECTION_OFFSET + 1) - option _ROMBASE = (CONFIG_ROM_STREAM_START + PAYLOAD_SIZE) - -# option XIP_ROM_SIZE = FALLBACK_SIZE - option XIP_ROM_SIZE = 65536 - option XIP_ROM_BASE = (_ROMBASE + ROM_IMAGE_SIZE - XIP_ROM_SIZE) - - mainboard tyan/s2875 -# payload ../../../payloads/e1000--ide_disk.zelf +# 48K for SCSI FW and 48K for ATI ROM +# option ROM_SIZE = 425984 +# 64K for Etherboot +# option ROM_SIZE = 458752 + option USE_FALLBACK_IMAGE=0 + option ROM_IMAGE_SIZE=0x10000 + option LINUXBIOS_EXTRA_VERSION="$(shell cat ../../VERSION)_Normal" +# payload ../../../payloads/tg3--ide_disk.zelf # payload ../../../payloads/filo.elf # payload ../../../payloads/filo_mem.elf -# payload ../../../payloads/filo_mem_btext.elf # payload ../../../payloads/filo.zelf - payload ../../../payloads/e1000--filo.zelf +# payload ../../../payloads/tg3--filo.zelf +# payload ../../../payloads/e1000--filo.zelf +# payload ../../../payloads/tg3--e1000--filo.zelf + payload ../../../payloads/tg3--eepro100--e1000--filo_hda2.zelf end romimage "fallback" - option LINUXBIOS_EXTRA_VERSION="$(shell cat ../../VERSION)_Fallback" option USE_FALLBACK_IMAGE=1 - option ROM_SECTION_SIZE = FALLBACK_SIZE - option ROM_SECTION_OFFSET= (ROM_SIZE - FALLBACK_SIZE) - - option PAYLOAD_SIZE = (ROM_SECTION_SIZE - ROM_IMAGE_SIZE) - option CONFIG_ROM_STREAM_START = (0xffffffff - ROM_SIZE + ROM_SECTION_OFFSET + 1) - option _ROMBASE = (CONFIG_ROM_STREAM_START + PAYLOAD_SIZE) - -# option XIP_ROM_SIZE = FALLBACK_SIZE - option XIP_ROM_SIZE = 65536 - option XIP_ROM_BASE = (_ROMBASE + ROM_IMAGE_SIZE - XIP_ROM_SIZE) - - mainboard tyan/s2875 -# payload ../../../payloads/e1000--ide_disk.zelf + option ROM_IMAGE_SIZE=0x10000 + option LINUXBIOS_EXTRA_VERSION="$(shell cat ../../VERSION)_Fallback" +# payload ../../../payloads/tg3--ide_disk.zelf # payload ../../../payloads/filo.elf # payload ../../../payloads/filo_mem.elf -# payload ../../../payloads/filo_mem_btext.elf # payload ../../../payloads/filo.zelf - payload ../../../payloads/e1000--filo.zelf +# payload ../../../payloads/tg3--filo.zelf +# payload ../../../payloads/e1000--filo.zelf +# payload ../../../payloads/tg3--e1000--filo.zelf + payload ../../../payloads/tg3--eepro100--e1000--filo_hda2.zelf end buildrom ./linuxbios.rom ROM_SIZE "normal" "fallback" |