summaryrefslogtreecommitdiff
path: root/src
diff options
context:
space:
mode:
Diffstat (limited to 'src')
-rw-r--r--src/mainboard/google/brya/variants/gothrax/gpio.c8
-rw-r--r--src/mainboard/google/brya/variants/gothrax/overridetree.cb418
2 files changed, 424 insertions, 2 deletions
diff --git a/src/mainboard/google/brya/variants/gothrax/gpio.c b/src/mainboard/google/brya/variants/gothrax/gpio.c
index cc2ee736d6..ab3b641f8c 100644
--- a/src/mainboard/google/brya/variants/gothrax/gpio.c
+++ b/src/mainboard/google/brya/variants/gothrax/gpio.c
@@ -26,6 +26,9 @@ static const struct pad_config override_gpio_table[] = {
/* B6 : SOC_I2C_SUB_SCL */
PAD_NC_LOCK(GPP_B6, NONE, LOCK_CONFIG),
+ /* C1 : SMBDATA ==> TCHSCR_RST_L */
+ PAD_CFG_GPO(GPP_C1, 1, DEEP),
+
/* D3 : WCAM_RST_L */
PAD_NC_LOCK(GPP_D3, NONE, LOCK_CONFIG),
/* D15 : EN_PP2800_WCAM_X */
@@ -69,6 +72,11 @@ static const struct pad_config early_gpio_table[] = {
};
static const struct pad_config romstage_gpio_table[] = {
+ /* Enable touchscreen, hold in reset */
+ /* C0 : SMBCLK ==> EN_PP3300_TCHSCR_X */
+ PAD_CFG_GPO(GPP_C0, 1, DEEP),
+ /* C1 : SMBDATA ==> TCHSCR_RST_L */
+ PAD_CFG_GPO(GPP_C1, 0, DEEP),
/* H12 : UART0_RTS# ==> SD_PERST_L */
PAD_CFG_GPO(GPP_H12, 1, DEEP),
/* H20 : IMGCLKOUT1 ==> WLAN_PERST_L */
diff --git a/src/mainboard/google/brya/variants/gothrax/overridetree.cb b/src/mainboard/google/brya/variants/gothrax/overridetree.cb
index 52956e63cd..0cc0954ae9 100644
--- a/src/mainboard/google/brya/variants/gothrax/overridetree.cb
+++ b/src/mainboard/google/brya/variants/gothrax/overridetree.cb
@@ -1,4 +1,28 @@
+fw_config
+ field DB_USB 0 1
+ option DB_NONE 0
+ option DB_C_A 1
+ option DB_C_LTE 2
+ end
+ field THERMAL_SOLUTION 2
+ option THERMAL_SOLUTION_PASSIVE 0
+ option THERMAL_SOLUTION_ACTIVE 1
+ end
+ field WLAN 3 4
+ option WLAN_MT7921_AZUREWAVE 0
+ option WLAN_AX211_Intel 1
+ end
+ field AUDIO 5 6
+ option AUDIO_ALC1019_ALC5682IVS 0
+ end
+ field STYLUS 7
+ option STYLUS_ABSENT 0
+ option STYLUS_PRESENT 1
+ end
+end
+
chip soc/intel/alderlake
+ register "sagv" = "SaGv_Enabled"
# EMMC Tx CMD Delay
# Refer to EDS-Vol2-42.3.7.
@@ -45,7 +69,397 @@ chip soc/intel/alderlake
# [6:0] Rx Strobe Delay DLL 2(HS400 Mode), each 125ps, range: 0 - 39.
register "common_soc_config.emmc_dll.emmc_rx_strobe_cntl" = "0x01515"
- device domain 0 on
- end
+ # Bit 0 - C0 has no redriver, so enable SBU muxing in the SoC.
+ # Bit 2 - C1 has a redriver which does SBU muxing.
+ # Bit 1,3 - AUX lines are not swapped on the motherboard for either C0 or C1.
+ register "tcss_aux_ori" = "5"
+
+ register "typec_aux_bias_pads[0]" = "{.pad_auxp_dc = GPP_E22, .pad_auxn_dc = GPP_E23}"
+ register "typec_aux_bias_pads[1]" = "{.pad_auxp_dc = GPP_A21, .pad_auxn_dc = GPP_A22}"
+
+ # Configure external V1P05/Vnn/VnnSx Rails
+ register "ext_fivr_settings" = "{
+ .configure_ext_fivr = 1,
+ .v1p05_enable_bitmap = FIVR_ENABLE_ALL_SX & ~FIVR_ENABLE_S0,
+ .vnn_enable_bitmap = FIVR_ENABLE_ALL_SX,
+ .vnn_sx_enable_bitmap = FIVR_ENABLE_ALL_SX,
+ .v1p05_supported_voltage_bitmap = FIVR_VOLTAGE_NORMAL,
+ .vnn_supported_voltage_bitmap = FIVR_VOLTAGE_MIN_ACTIVE,
+ .v1p05_voltage_mv = 1050,
+ .vnn_voltage_mv = 780,
+ .vnn_sx_voltage_mv = 1050,
+ .v1p05_icc_max_ma = 500,
+ .vnn_icc_max_ma = 500,
+ }"
+
+ # Intel Common SoC Config
+ #+-------------------+---------------------------+
+ #| Field | Value |
+ #+-------------------+---------------------------+
+ #| I2C0 | TPM. Early init is |
+ #| | required to set up a BAR |
+ #| | for TPM communication |
+ #| I2C1 | Touchscreen |
+ #| I2C2 | Sub-board(PSensor)/WCAM |
+ #| I2C3 | Audio |
+ #| I2C5 | Trackpad |
+ #+-------------------+---------------------------+
+ register "common_soc_config" = "{
+ .i2c[0] = {
+ .early_init = 1,
+ .speed = I2C_SPEED_FAST_PLUS,
+ .speed_config[0] = {
+ .speed = I2C_SPEED_FAST_PLUS,
+ .scl_lcnt = 55,
+ .scl_hcnt = 30,
+ .sda_hold = 7,
+ }
+ },
+ .i2c[1] = {
+ .speed = I2C_SPEED_FAST,
+ .speed_config[0] = {
+ .speed = I2C_SPEED_FAST,
+ .scl_lcnt = 160,
+ .scl_hcnt = 79,
+ .sda_hold = 7,
+ }
+ },
+ .i2c[2] = {
+ .speed = I2C_SPEED_FAST,
+ .speed_config[0] = {
+ .speed = I2C_SPEED_FAST,
+ .scl_lcnt = 157,
+ .scl_hcnt = 79,
+ .sda_hold = 7,
+ }
+ },
+ .i2c[3] = {
+ .speed = I2C_SPEED_FAST,
+ .speed_config[0] = {
+ .speed = I2C_SPEED_FAST,
+ .scl_lcnt = 157,
+ .scl_hcnt = 79,
+ .sda_hold = 7,
+ }
+ },
+ .i2c[5] = {
+ .speed = I2C_SPEED_FAST,
+ .speed_config[0] = {
+ .speed = I2C_SPEED_FAST,
+ .scl_lcnt = 152,
+ .scl_hcnt = 79,
+ .sda_hold = 7,
+ }
+ },
+ }"
+
+ device domain 0 on
+ device ref dtt on
+ chip drivers/intel/dptf
+ ## sensor information
+ register "options.tsr[0].desc" = ""Memory""
+ register "options.tsr[1].desc" = ""Charger""
+ register "options.tsr[2].desc" = ""Ambient""
+
+ # TODO: below values are initial reference values only
+ ## Passive Policy
+ register "policies.passive" = "{
+ [0] = DPTF_PASSIVE(CPU, CPU, 95, 5000),
+ [1] = DPTF_PASSIVE(CPU, TEMP_SENSOR_0, 75, 5000),
+ [2] = DPTF_PASSIVE(CHARGER, TEMP_SENSOR_1, 75, 5000),
+ [3] = DPTF_PASSIVE(CPU, TEMP_SENSOR_2, 75, 5000),
+ }"
+
+ ## Critical Policy
+ register "policies.critical" = "{
+ [0] = DPTF_CRITICAL(CPU, 105, SHUTDOWN),
+ [1] = DPTF_CRITICAL(TEMP_SENSOR_0, 85, SHUTDOWN),
+ [2] = DPTF_CRITICAL(TEMP_SENSOR_1, 85, SHUTDOWN),
+ [3] = DPTF_CRITICAL(TEMP_SENSOR_2, 85, SHUTDOWN),
+ }"
+
+ register "controls.power_limits" = "{
+ .pl1 = {
+ .min_power = 3000,
+ .max_power = 6000,
+ .time_window_min = 28 * MSECS_PER_SEC,
+ .time_window_max = 32 * MSECS_PER_SEC,
+ .granularity = 200
+ },
+ .pl2 = {
+ .min_power = 25000,
+ .max_power = 25000,
+ .time_window_min = 28 * MSECS_PER_SEC,
+ .time_window_max = 32 * MSECS_PER_SEC,
+ .granularity = 1000
+ }
+ }"
+
+ ## Charger Performance Control (Control, mA)
+ register "controls.charger_perf" = "{
+ [0] = { 255, 1700 },
+ [1] = { 24, 1500 },
+ [2] = { 16, 1000 },
+ [3] = { 8, 500 }
+ }"
+
+ device generic 0 on end
+ end
+ end
+ device ref i2c1 on
+ chip drivers/i2c/generic
+ register "hid" = ""ELAN0001""
+ register "desc" = ""ELAN Touchscreen""
+ register "irq" = "ACPI_IRQ_LEVEL_LOW(GPP_C7_IRQ)"
+ register "detect" = "1"
+ register "reset_gpio" =
+ "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C1)"
+ register "reset_delay_ms" = "20"
+ register "enable_gpio" =
+ "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_C0)"
+ register "enable_delay_ms" = "1"
+ register "has_power_resource" = "1"
+ device i2c 0x10 on end
+ end
+ end
+ device ref i2c2 on
+ chip drivers/i2c/sx9324
+ register "desc" = ""SAR2 Proximity Sensor""
+ register "irq" = "ACPI_IRQ_LEVEL_LOW(GPP_H19_IRQ)"
+ register "speed" = "I2C_SPEED_FAST"
+ register "uid" = "2"
+ register "reg_gnrl_ctrl0" = "0x16"
+ register "reg_gnrl_ctrl1" = "0x21"
+ register "reg_afe_ctrl0" = "0x00"
+ register "reg_afe_ctrl1" = "0x10"
+ register "reg_afe_ctrl2" = "0x00"
+ register "reg_afe_ctrl3" = "0x00"
+ register "reg_afe_ctrl4" = "0x07"
+ register "reg_afe_ctrl5" = "0x00"
+ register "reg_afe_ctrl6" = "0x00"
+ register "reg_afe_ctrl7" = "0x07"
+ register "reg_afe_ctrl8" = "0x12"
+ register "reg_afe_ctrl9" = "0x0f"
+ register "reg_prox_ctrl0" = "0x12"
+ register "reg_prox_ctrl1" = "0x12"
+ register "reg_prox_ctrl2" = "0x90"
+ register "reg_prox_ctrl3" = "0x60"
+ register "reg_prox_ctrl4" = "0x0c"
+ register "reg_prox_ctrl5" = "0x12"
+ register "reg_prox_ctrl6" = "0x3c"
+ register "reg_prox_ctrl7" = "0x58"
+ register "reg_adv_ctrl0" = "0x00"
+ register "reg_adv_ctrl1" = "0x00"
+ register "reg_adv_ctrl2" = "0x00"
+ register "reg_adv_ctrl3" = "0x00"
+ register "reg_adv_ctrl4" = "0x00"
+ register "reg_adv_ctrl5" = "0x05"
+ register "reg_adv_ctrl6" = "0x00"
+ register "reg_adv_ctrl7" = "0x00"
+ register "reg_adv_ctrl8" = "0x00"
+ register "reg_adv_ctrl9" = "0x00"
+ register "reg_adv_ctrl10" = "0x5c"
+ register "reg_adv_ctrl11" = "0x52"
+ register "reg_adv_ctrl12" = "0xb5"
+ register "reg_adv_ctrl13" = "0x00"
+ register "reg_adv_ctrl14" = "0x80"
+ register "reg_adv_ctrl15" = "0x0c"
+ register "reg_adv_ctrl16" = "0x38"
+ register "reg_adv_ctrl17" = "0x56"
+ register "reg_adv_ctrl18" = "0x33"
+ register "reg_adv_ctrl19" = "0xf0"
+ register "reg_adv_ctrl20" = "0xf0"
+ device i2c 28 on end
+ end
+ end
+ device ref i2c3 on
+ chip drivers/i2c/generic
+ register "hid" = ""RTL5682""
+ register "name" = ""RT58""
+ register "desc" = ""Headset Codec""
+ register "irq_gpio" = "ACPI_GPIO_IRQ_EDGE_BOTH(GPP_A23)"
+ # Set the jd_src to RT5668_JD1 for jack detection
+ register "property_count" = "1"
+ register "property_list[0].type" = "ACPI_DP_TYPE_INTEGER"
+ register "property_list[0].name" = ""realtek,jd-src""
+ register "property_list[0].integer" = "1"
+ device i2c 1a on end
+ end
+ chip drivers/generic/alc1015
+ register "hid" = ""RTL1019""
+ register "sdb" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_A11)"
+ device generic 0 on end
+ end
+ end
+
+ device ref i2c5 on
+ chip drivers/i2c/hid
+ register "generic.hid" = ""PNP0C50""
+ register "generic.desc" = ""PIXART Touchpad""
+ register "generic.irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_F14_IRQ)"
+ register "generic.wake" = "GPE0_DW2_14"
+ register "generic.detect" = "1"
+ register "hid_desc_reg_offset" = "0x01"
+ device i2c 15 on end
+ end
+ end
+ device ref pcie_rp4 on
+ # PCIe 4 WLAN
+ register "pch_pcie_rp[PCH_RP(4)]" = "{
+ .clk_src = 2,
+ .clk_req = 2,
+ .flags = PCIE_RP_LTR | PCIE_RP_AER,
+ }"
+ chip drivers/wifi/generic
+ register "wake" = "GPE0_DW1_03"
+ register "add_acpi_dma_property" = "true"
+ device pci 00.0 on end
+ end
+ end
+ device ref pcie_rp7 on
+ # Enable SD Card PCIe 7 using clk 3
+ register "pch_pcie_rp[PCH_RP(7)]" = "{
+ .clk_src = 3,
+ .clk_req = 3,
+ .flags = PCIE_RP_HOTPLUG | PCIE_RP_LTR | PCIE_RP_AER,
+ }"
+ chip soc/intel/common/block/pcie/rtd3
+ register "enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_H13)"
+ register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_H12)"
+ register "srcclk_pin" = "3"
+ device generic 0 on end
+ end
+ end
+ device ref pch_espi on
+ chip ec/google/chromeec
+ use conn0 as mux_conn[0]
+ use conn1 as mux_conn[1]
+ device pnp 0c09.0 on end
+ end
+ end
+ device ref pmc hidden
+ chip drivers/intel/pmc_mux
+ device generic 0 on
+ chip drivers/intel/pmc_mux/conn
+ use usb2_port1 as usb2_port
+ use tcss_usb3_port1 as usb3_port
+ device generic 0 alias conn0 on end
+ end
+ chip drivers/intel/pmc_mux/conn
+ use usb2_port2 as usb2_port
+ use tcss_usb3_port2 as usb3_port
+ device generic 1 alias conn1 on end
+ end
+ end
+ end
+ end
+ device ref tcss_xhci on
+ chip drivers/usb/acpi
+ device ref tcss_root_hub on
+ chip drivers/usb/acpi
+ register "desc" = ""USB3 Type-C Port C0 (MLB)""
+ register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
+ register "use_custom_pld" = "true"
+ register "custom_pld" = "ACPI_PLD_TYPE_C(LEFT, LEFT, ACPI_PLD_GROUP(1, 1))"
+ device ref tcss_usb3_port1 on end
+ end
+ chip drivers/usb/acpi
+ register "desc" = ""USB3 Type-C Port C1 (DB)""
+ register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
+ register "use_custom_pld" = "true"
+ register "custom_pld" = "ACPI_PLD_TYPE_C(RIGHT, RIGHT, ACPI_PLD_GROUP(2, 1))"
+ device ref tcss_usb3_port2 on end
+ end
+ end
+ end
+ end
+ device ref xhci on
+ register "usb2_ports[4]" = "USB2_PORT_MID(OC_SKIP)" # USB2_A1
+ register "usb2_ports[6]" = "USB2_PORT_MID(OC_SKIP)" # WFC
+ register "usb2_ports[7]" = "USB2_PORT_MID(OC_SKIP)" # Bluetooth port for PCIe WLAN
+ register "usb2_ports[9]" = "USB2_PORT_MID(OC_SKIP)" # Bluetooth port for CNVi WLAN
+ register "usb3_ports[2]" = "USB3_PORT_DEFAULT(OC_SKIP)" # USB3/3 Type A port A1
+ chip drivers/usb/acpi
+ device ref xhci_root_hub on
+ chip drivers/usb/acpi
+ register "desc" = ""USB2 Type-C Port C0 (MLB)""
+ register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
+ register "use_custom_pld" = "true"
+ register "custom_pld" = "ACPI_PLD_TYPE_C(LEFT, LEFT, ACPI_PLD_GROUP(1, 1))"
+ device ref usb2_port1 on end
+ end
+ chip drivers/usb/acpi
+ register "desc" = ""USB2 Type-C Port C1 (DB)""
+ register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
+ register "use_custom_pld" = "true"
+ register "custom_pld" = "ACPI_PLD_TYPE_C(RIGHT, RIGHT, ACPI_PLD_GROUP(2, 1))"
+ device ref usb2_port2 on end
+ end
+ chip drivers/usb/acpi
+ register "desc" = ""USB2 Type-A Port A0 (MLB)""
+ register "type" = "UPC_TYPE_A"
+ register "use_custom_pld" = "true"
+ register "custom_pld" = "ACPI_PLD_TYPE_A(LEFT, RIGHT, ACPI_PLD_GROUP(3, 1))"
+ device ref usb2_port3 on end
+ end
+ chip drivers/usb/acpi
+ register "desc" = ""USB2 Type-A Port A1 (DB)""
+ register "type" = "UPC_TYPE_A"
+ register "use_custom_pld" = "true"
+ register "custom_pld" = "ACPI_PLD_TYPE_A(RIGHT, LEFT, ACPI_PLD_GROUP(4, 1))"
+ device ref usb2_port4 on end
+ end
+ chip drivers/usb/acpi
+ register "desc" = ""USB2 WWAN""
+ register "type" = "UPC_TYPE_INTERNAL"
+ device ref usb2_port5 on end
+ end
+ chip drivers/usb/acpi
+ register "desc" = ""USB2 UFC""
+ register "type" = "UPC_TYPE_INTERNAL"
+ device ref usb2_port6 on end
+ end
+ chip drivers/usb/acpi
+ register "desc" = ""USB2 WFC""
+ register "type" = "UPC_TYPE_INTERNAL"
+ device ref usb2_port7 on end
+ end
+ chip drivers/usb/acpi
+ register "desc" = ""USB2 Bluetooth""
+ register "type" = "UPC_TYPE_INTERNAL"
+ register "reset_gpio" =
+ "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D4)"
+ device ref usb2_port8 on end
+ end
+ chip drivers/usb/acpi
+ register "desc" = ""CNVi Bluetooth""
+ register "type" = "UPC_TYPE_INTERNAL"
+ register "reset_gpio" =
+ "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D4)"
+ device ref usb2_port10 on end
+ end
+ chip drivers/usb/acpi
+ register "desc" = ""USB3 Type-A Port A0 (MLB)""
+ register "type" = "UPC_TYPE_USB3_A"
+ register "use_custom_pld" = "true"
+ register "custom_pld" = "ACPI_PLD_TYPE_A(LEFT, RIGHT, ACPI_PLD_GROUP(3, 1))"
+ device ref usb3_port1 on end
+ end
+ chip drivers/usb/acpi
+ register "desc" = ""USB3 Type-A Port A1 (DB)""
+ register "type" = "UPC_TYPE_USB3_A"
+ register "use_custom_pld" = "true"
+ register "custom_pld" = "ACPI_PLD_TYPE_A(RIGHT, LEFT, ACPI_PLD_GROUP(4, 1))"
+ device ref usb3_port2 on end
+ end
+ chip drivers/usb/acpi
+ register "desc" = ""USB3 WWAN""
+ register "type" = "UPC_TYPE_INTERNAL"
+ device ref usb3_port3 on end
+ end
+ end
+ end
+ end
+ end
end
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-28 13:14:33 +0000