summaryrefslogtreecommitdiff
path: root/src
diff options
context:
space:
mode:
Diffstat (limited to 'src')
-rw-r--r--src/mainboard/google/brya/Kconfig.name1
-rw-r--r--src/mainboard/google/brya/variants/joxer/gpio.c5
-rw-r--r--src/mainboard/google/brya/variants/joxer/overridetree.cb286
3 files changed, 290 insertions, 2 deletions
diff --git a/src/mainboard/google/brya/Kconfig.name b/src/mainboard/google/brya/Kconfig.name
index f2f3082657..7384a95f7d 100644
--- a/src/mainboard/google/brya/Kconfig.name
+++ b/src/mainboard/google/brya/Kconfig.name
@@ -246,6 +246,7 @@ config BOARD_GOOGLE_KULDAX
config BOARD_GOOGLE_JOXER
bool "-> Joxer"
select BOARD_GOOGLE_BASEBOARD_NISSA
+ select DRIVERS_GENESYSLOGIC_GL9750
config BOARD_GOOGLE_PUJJO
bool "-> Pujjo"
diff --git a/src/mainboard/google/brya/variants/joxer/gpio.c b/src/mainboard/google/brya/variants/joxer/gpio.c
index d1837e5d21..ec7ef795f9 100644
--- a/src/mainboard/google/brya/variants/joxer/gpio.c
+++ b/src/mainboard/google/brya/variants/joxer/gpio.c
@@ -7,6 +7,11 @@
/* Pad configuration in ramstage */
static const struct pad_config override_gpio_table[] = {
+ /* A21 : GPP_A21 ==> USB_C1_AUX_DC_P */
+ PAD_CFG_GPO(GPP_A21, 0, DEEP),
+ /* A22 : GPP_A22 ==> USB_C1_AUX_DC_N */
+ PAD_CFG_GPO(GPP_A22, 1, DEEP),
+
/* B5 : SOC_I2C_SUB_SDA ==> NC */
PAD_NC_LOCK(GPP_B5, NONE, LOCK_CONFIG),
/* B6 : SOC_I2C_SUB_SCL ==> NC */
diff --git a/src/mainboard/google/brya/variants/joxer/overridetree.cb b/src/mainboard/google/brya/variants/joxer/overridetree.cb
index 4f2c04a57a..70021f7cb3 100644
--- a/src/mainboard/google/brya/variants/joxer/overridetree.cb
+++ b/src/mainboard/google/brya/variants/joxer/overridetree.cb
@@ -1,6 +1,288 @@
chip soc/intel/alderlake
+ register "sagv" = "SaGv_Enabled"
- device domain 0 on
- end
+ # Bit 0 - C0 has no redriver, so enable SBU muxing in the SoC.
+ # Bit 2 - C1 has a redriver which does SBU muxing.
+ # Bit 1,3 - AUX lines are not swapped on the motherboard for either C0 or C1.
+ register "tcss_aux_ori" = "1"
+ register "typec_aux_bias_pads[0]" = "{.pad_auxp_dc = GPP_E22, .pad_auxn_dc = GPP_E23}"
+
+ register "usb2_ports[6]" = "USB2_PORT_MID(OC_SKIP)" # UFC
+ register "usb2_ports[7]" = "USB2_PORT_MID(OC_SKIP)" # Bluetooth port for PCIe WLAN
+ register "usb2_ports[9]" = "USB2_PORT_MID(OC_SKIP)" # Bluetooth port for CNVi WLAN
+
+ # Intel Common SoC Config
+ #+-------------------+---------------------------+
+ #| Field | Value |
+ #+-------------------+---------------------------+
+ #| I2C0 | TPM. Early init is |
+ #| | required to set up a BAR |
+ #| | for TPM communication |
+ #| I2C1 | Touchscreen |
+ #| I2C2 | Sub-board(PSensor)/WCAM |
+ #| I2C3 | Audio |
+ #| I2C5 | Trackpad |
+ #+-------------------+---------------------------+
+ register "common_soc_config" = "{
+ .i2c[0] = {
+ .early_init = 1,
+ .speed = I2C_SPEED_FAST,
+ .speed_config[0] = {
+ .speed = I2C_SPEED_FAST,
+ .scl_lcnt = 158,
+ .scl_hcnt = 79,
+ .sda_hold = 7,
+ }
+ },
+ .i2c[1] = {
+ .speed = I2C_SPEED_FAST,
+ .speed_config[0] = {
+ .speed = I2C_SPEED_FAST,
+ .scl_lcnt = 160,
+ .scl_hcnt = 79,
+ .sda_hold = 7,
+ }
+ },
+ .i2c[3] = {
+ .speed = I2C_SPEED_FAST,
+ .speed_config[0] = {
+ .speed = I2C_SPEED_FAST,
+ .scl_lcnt = 157,
+ .scl_hcnt = 79,
+ .sda_hold = 7,
+ }
+ },
+ .i2c[5] = {
+ .speed = I2C_SPEED_FAST,
+ .speed_config[0] = {
+ .speed = I2C_SPEED_FAST,
+ .scl_lcnt = 152,
+ .scl_hcnt = 79,
+ .sda_hold = 7,
+ }
+ },
+ }"
+
+ device domain 0 on
+ device ref dtt on
+ chip drivers/intel/dptf
+ ## sensor information
+ register "options.tsr[0].desc" = ""Memory""
+ register "options.tsr[1].desc" = ""Charger""
+ register "options.tsr[2].desc" = ""Ambient""
+
+ # TODO: below values are initial reference values only
+ ## Passive Policy
+ register "policies.passive" = "{
+ [0] = DPTF_PASSIVE(CPU, CPU, 95, 5000),
+ [1] = DPTF_PASSIVE(CPU, TEMP_SENSOR_0, 75, 5000),
+ [2] = DPTF_PASSIVE(CHARGER, TEMP_SENSOR_1, 75, 5000),
+ [3] = DPTF_PASSIVE(CPU, TEMP_SENSOR_2, 75, 5000),
+ }"
+
+ ## Critical Policy
+ register "policies.critical" = "{
+ [0] = DPTF_CRITICAL(CPU, 105, SHUTDOWN),
+ [1] = DPTF_CRITICAL(TEMP_SENSOR_0, 85, SHUTDOWN),
+ [2] = DPTF_CRITICAL(TEMP_SENSOR_1, 85, SHUTDOWN),
+ [3] = DPTF_CRITICAL(TEMP_SENSOR_2, 85, SHUTDOWN),
+ }"
+
+ register "controls.power_limits" = "{
+ .pl1 = {
+ .min_power = 3000,
+ .max_power = 6000,
+ .time_window_min = 28 * MSECS_PER_SEC,
+ .time_window_max = 32 * MSECS_PER_SEC,
+ .granularity = 200
+ },
+ .pl2 = {
+ .min_power = 25000,
+ .max_power = 25000,
+ .time_window_min = 28 * MSECS_PER_SEC,
+ .time_window_max = 32 * MSECS_PER_SEC,
+ .granularity = 1000
+ }
+ }"
+
+ ## Charger Performance Control (Control, mA)
+ register "controls.charger_perf" = "{
+ [0] = { 255, 1700 },
+ [1] = { 24, 1500 },
+ [2] = { 16, 1000 },
+ [3] = { 8, 500 }
+ }"
+
+ device generic 0 on end
+ end
+ end
+ device ref i2c1 on
+ chip drivers/i2c/hid
+ register "generic.hid" = ""GDIX0000""
+ register "generic.desc" = ""Goodix Touchscreen""
+ register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPP_C7_IRQ)"
+ register "generic.probed" = "1"
+ register "generic.enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_C0)"
+ register "generic.enable_delay_ms" = "20"
+ register "generic.reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C1)"
+ register "generic.reset_delay_ms" = "180"
+ register "generic.reset_off_delay_ms" = "3"
+ register "generic.stop_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C6)"
+ register "generic.stop_off_delay_ms" = "1"
+ register "generic.has_power_resource" = "1"
+ register "hid_desc_reg_offset" = "0x01"
+ device i2c 5d on end
+ end
+ end
+ device ref i2c3 on
+ chip drivers/i2c/generic
+ register "hid" = ""RTL5682""
+ register "name" = ""RT58""
+ register "desc" = ""Headset Codec""
+ register "irq_gpio" = "ACPI_GPIO_IRQ_EDGE_BOTH(GPP_A23)"
+ # Set the jd_src to RT5668_JD1 for jack detection
+ register "property_count" = "1"
+ register "property_list[0].type" = "ACPI_DP_TYPE_INTEGER"
+ register "property_list[0].name" = ""realtek,jd-src""
+ register "property_list[0].integer" = "1"
+ device i2c 1a on end
+ end
+ end
+ device ref i2c5 on
+ chip drivers/i2c/generic
+ register "hid" = ""ELAN0000""
+ register "desc" = ""ELAN Touchpad""
+ register "irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_F14_IRQ)"
+ register "wake" = "GPE0_DW2_14"
+ register "probed" = "1"
+ device i2c 15 on end
+ end
+ end
+ device ref hda on
+ chip drivers/generic/max98357a
+ register "hid" = ""MX98360A""
+ register "sdmode_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_A11)"
+ register "sdmode_delay" = "5"
+ device generic 0 on end
+ end
+ end
+ device ref pcie_rp4 on
+ # PCIe 4 WLAN
+ register "pch_pcie_rp[PCH_RP(4)]" = "{
+ .clk_src = 2,
+ .clk_req = 2,
+ .flags = PCIE_RP_LTR | PCIE_RP_AER,
+ }"
+ chip drivers/wifi/generic
+ register "wake" = "GPE0_DW1_03"
+ device pci 00.0 on end
+ end
+ end
+ device ref emmc on
+ probe STORAGE STORAGE_EMMC
+ end
+ device ref ish on
+ probe STORAGE STORAGE_UFS
+ end
+ device ref ufs on
+ probe STORAGE STORAGE_UFS
+ end
+ device ref pch_espi on
+ chip ec/google/chromeec
+ use conn0 as mux_conn[0]
+ use conn1 as mux_conn[1]
+ device pnp 0c09.0 on end
+ end
+ end
+ device ref pmc hidden
+ chip drivers/intel/pmc_mux
+ device generic 0 on
+ chip drivers/intel/pmc_mux/conn
+ use usb2_port1 as usb2_port
+ use tcss_usb3_port1 as usb3_port
+ device generic 0 alias conn0 on end
+ end
+ chip drivers/intel/pmc_mux/conn
+ use usb2_port2 as usb2_port
+ use tcss_usb3_port2 as usb3_port
+ device generic 1 alias conn1 on end
+ end
+ end
+ end
+ end
+ device ref tcss_xhci on
+ chip drivers/usb/acpi
+ device ref tcss_root_hub on
+ chip drivers/usb/acpi
+ register "desc" = ""USB3 Type-C Port C0 (MLB)""
+ register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
+ register "use_custom_pld" = "true"
+ register "custom_pld" = "ACPI_PLD_TYPE_C(LEFT, LEFT, ACPI_PLD_GROUP(1, 1))"
+ device ref tcss_usb3_port1 on end
+ end
+ chip drivers/usb/acpi
+ register "desc" = ""USB3 Type-C Port C1 (DB)""
+ register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
+ register "use_custom_pld" = "true"
+ register "custom_pld" = "ACPI_PLD_TYPE_C(RIGHT, RIGHT, ACPI_PLD_GROUP(2, 1))"
+ device ref tcss_usb3_port2 on end
+ end
+ end
+ end
+ end
+ device ref xhci on
+ chip drivers/usb/acpi
+ device ref xhci_root_hub on
+ chip drivers/usb/acpi
+ register "desc" = ""USB2 Type-C Port C0 (MLB)""
+ register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
+ register "use_custom_pld" = "true"
+ register "custom_pld" = "ACPI_PLD_TYPE_C(LEFT, LEFT, ACPI_PLD_GROUP(1, 1))"
+ device ref usb2_port1 on end
+ end
+ chip drivers/usb/acpi
+ register "desc" = ""USB2 Type-C Port C1 (DB)""
+ register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
+ register "use_custom_pld" = "true"
+ register "custom_pld" = "ACPI_PLD_TYPE_C(RIGHT, RIGHT, ACPI_PLD_GROUP(2, 1))"
+ device ref usb2_port2 on end
+ end
+ chip drivers/usb/acpi
+ register "desc" = ""USB2 Type-A Port A0 (MLB)""
+ register "type" = "UPC_TYPE_A"
+ register "use_custom_pld" = "true"
+ register "custom_pld" = "ACPI_PLD_TYPE_A(LEFT, RIGHT, ACPI_PLD_GROUP(3, 1))"
+ device ref usb2_port3 on end
+ end
+ chip drivers/usb/acpi
+ register "desc" = ""USB2 UFC""
+ register "type" = "UPC_TYPE_INTERNAL"
+ device ref usb2_port7 on end
+ end
+ chip drivers/usb/acpi
+ register "desc" = ""USB2 Bluetooth""
+ register "type" = "UPC_TYPE_INTERNAL"
+ register "reset_gpio" =
+ "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D4)"
+ device ref usb2_port8 on end
+ end
+ chip drivers/usb/acpi
+ register "desc" = ""CNVi Bluetooth""
+ register "type" = "UPC_TYPE_INTERNAL"
+ register "reset_gpio" =
+ "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D4)"
+ device ref usb2_port10 on end
+ end
+ chip drivers/usb/acpi
+ register "desc" = ""USB3 Type-A Port A0 (MLB)""
+ register "type" = "UPC_TYPE_USB3_A"
+ register "use_custom_pld" = "true"
+ register "custom_pld" = "ACPI_PLD_TYPE_A(LEFT, RIGHT, ACPI_PLD_GROUP(3, 1))"
+ device ref usb3_port1 on end
+ end
+ end
+ end
+ end
+ end
end
generated by cgit v1.2.3 (git 2.25.1) at 2024-12-03 06:53:50 +0000