diff options
Diffstat (limited to 'src')
-rw-r--r-- | src/soc/amd/stoneyridge/include/soc/southbridge.h | 252 |
1 files changed, 130 insertions, 122 deletions
diff --git a/src/soc/amd/stoneyridge/include/soc/southbridge.h b/src/soc/amd/stoneyridge/include/soc/southbridge.h index 0aeb0fc12e..d25c90ba68 100644 --- a/src/soc/amd/stoneyridge/include/soc/southbridge.h +++ b/src/soc/amd/stoneyridge/include/soc/southbridge.h @@ -26,10 +26,10 @@ #include "chip.h" #include <rules.h> -/* PSP at D8F0 */ -#define PSP_MAILBOX_BAR PCI_BASE_ADDRESS_4 /* BKDG: "BAR3" */ -#define PSP_BAR_ENABLES 0x48 -#define PSP_MAILBOX_BAR_EN 0x10 +/* + * AcpiMmio Region + * - fixed addresses offset from 0xfed80000 + */ /* Power management registers: 0xfed80300 or index/data at IO 0xcd6/cd7 */ #define PM_DECODE_EN 0x00 @@ -40,6 +40,10 @@ #define PM_PCI_CTRL 0x08 #define FORCE_SLPSTATE_RETRY BIT(25) #define FORCE_STPCLK_RETRY BIT(24) + +#define PWR_RESET_CFG 0x10 +#define TOGGLE_ALL_PWR_GOOD BIT(1) + #define PM_SERIRQ_CONF 0x54 #define PM_SERIRQ_NUM_BITS_17 0x0000 #define PM_SERIRQ_NUM_BITS_18 0x0004 @@ -105,6 +109,114 @@ #define SPI_ROM_ALT_ENABLE BIT(0) #define SPI_PRESERVE_BITS (BIT(0) | BIT(1) | BIT(2) | BIT(3)) +/* FCH MISC Registers 0xfed80e00 */ +#define GPP_CLK_CNTRL 0 +#define GPP_CLK2_CLOCK_REQ_MAP_SHIFT 8 +#define GPP_CLK2_CLOCK_REQ_MAP_MASK (0xf << GPP_CLK2_CLOCK_REQ_MAP_SHIFT) +#define GPP_CLK2_CLOCK_REQ_MAP_CLK_REQ2 3 + +#define GPP_CLK0_CLOCK_REQ_MAP_SHIFT 0 +#define GPP_CLK0_CLOCK_REQ_MAP_MASK (0xf << GPP_CLK0_CLOCK_REQ_MAP_SHIFT) +#define GPP_CLK0_CLOCK_REQ_MAP_CLK_REQ0 1 + +#define MISC_CGPLL_CONFIG1 0x08 +#define CG1PLL_SPREAD_SPECTRUM_ENABLE BIT(0) +#define MISC_CGPLL_CONFIG3 0x10 +#define CG1PLL_REFDIV_SHIFT 0 +#define CG1PLL_REFDIV_MASK (0x3ff << CG1PLL_REFDIV_SHIFT) +#define CG1PLL_FBDIV_SHIFT 10 +#define CG1PLL_FBDIV_MASK (0xfff << CG1PLL_FBDIV_SHIFT) +#define MISC_CGPLL_CONFIG4 0x14 +#define CG1PLL_SS_STEP_SIZE_DSFRAC_SHIFT 0 +#define CG1PLL_SS_STEP_SIZE_DSFRAC_MASK (0xffff << CG1PLL_SS_STEP_SIZE_DSFRAC_SHIFT) +#define CG1PLL_SS_AMOUNT_DSFRAC_SHIFT 16 +#define CG1PLL_SS_AMOUNT_DSFRAC_MASK (0xffff << CG1PLL_SS_AMOUNT_DSFRAC_SHIFT) +#define MISC_CGPLL_CONFIG5 0x18 +#define CG1PLL_SS_AMOUNT_NFRAC_SLIP_SHIFT 8 +#define CG1PLL_SS_AMOUNT_NFRAC_SLIP_MASK (0xf << CG1PLL_SS_AMOUNT_NFRAC_SLIP_SHIFT) +#define MISC_CGPLL_CONFIG6 0x1c +#define CG1PLL_LF_MODE_SHIFT 9 +#define CG1PLL_LF_MODE_MASK (0x1ff << CG1PLL_LF_MODE_SHIFT) +#define MISC_CLK_CNTL1 0x40 +#define CG1PLL_FBDIV_TEST BIT(26) + +/* XHCI_PM Registers: 0xfed81c00 */ +#define XHCI_PM_INDIRECT_INDEX 0x48 +#define XHCI_PM_INDIRECT_DATA 0x4c +#define XHCI_OVER_CURRENT_CONTROL 0x30 +#define USB_OC0 0 +#define USB_OC1 1 +#define USB_OC2 2 +#define USB_OC3 3 +#define USB_OC4 4 +#define USB_OC5 5 +#define USB_OC6 6 +#define USB_OC7 7 +#define USB_OC_DISABLE 0xf +#define USB_OC_DISABLE_ALL 0xffff +#define OC_PORT0_SHIFT 0 +#define OC_PORT1_SHIFT 4 +#define OC_PORT2_SHIFT 8 +#define OC_PORT3_SHIFT 12 + +#define EHCI_OVER_CURRENT_CONTROL 0x70 +#define EHCI_HUB_CONFIG4 0x90 +#define DEBUG_PORT_SELECT_SHIFT 16 +#define DEBUG_PORT_ENABLE BIT(18) +#define DEBUG_PORT_MASK (BIT(16) | BIT(17) | (BIT(18)) + +#define WIDEIO_RANGE_ERROR -1 +#define TOTAL_WIDEIO_PORTS 3 + +/* FCH AOAC Registers 0xfed81e00 */ +#define FCH_AOAC_D3_CONTROL_CLK_GEN 0x40 +#define FCH_AOAC_D3_CONTROL_I2C0 0x4a +#define FCH_AOAC_D3_CONTROL_I2C1 0x4c +#define FCH_AOAC_D3_CONTROL_I2C2 0x4e +#define FCH_AOAC_D3_CONTROL_I2C3 0x50 +#define FCH_AOAC_D3_CONTROL_UART0 0x56 +#define FCH_AOAC_D3_CONTROL_UART1 0x58 +#define FCH_AOAC_D3_CONTROL_AMBA 0x62 +#define FCH_AOAC_D3_CONTROL_USB2 0x64 +#define FCH_AOAC_D3_CONTROL_USB3 0x6e +/* Bit definitions for all FCH_AOAC_D3_CONTROL_* Registers */ +#define FCH_AOAC_TARGET_DEVICE_STATE (BIT(0) + BIT(1)) +#define FCH_AOAC_DEVICE_STATE BIT(2) +#define FCH_AOAC_PWR_ON_DEV BIT(3) +#define FCH_AOAC_SW_PWR_ON_RSTB BIT(4) +#define FCH_AOAC_SW_REF_CLK_OK BIT(5) +#define FCH_AOAC_SW_RST_B BIT(6) +#define FCH_AOAC_IS_SW_CONTROL BIT(7) + +#define FCH_AOAC_D3_STATE_CLK_GEN 0x41 +#define FCH_AOAC_D3_STATE_I2C0 0x4b +#define FCH_AOAC_D3_STATE_I2C1 0x4d +#define FCH_AOAC_D3_STATE_I2C2 0x4f +#define FCH_AOAC_D3_STATE_I2C3 0x51 +#define FCH_AOAC_D3_STATE_UART0 0x57 +#define FCH_AOAC_D3_STATE_UART1 0x59 +#define FCH_AOAC_D3_STATE_AMBA 0x63 +#define FCH_AOAC_D3_STATE_USB2 0x65 +#define FCH_AOAC_D3_STATE_USB3 0x6f +/* Bit definitions for all FCH_AOAC_D3_STATE_* Registers */ +#define FCH_AOAC_PWR_RST_STATE BIT(0) +#define FCH_AOAC_RST_CLK_OK_STATE BIT(1) +#define FCH_AOAC_RST_B_STATE BIT(2) +#define FCH_AOAC_DEV_OFF_GATING_STATE BIT(3) +#define FCH_AOAC_D3COLD BIT(4) +#define FCH_AOAC_CLK_OK_STATE BIT(5) +#define FCH_AOAC_STAT0 BIT(6) +#define FCH_AOAC_STAT1 BIT(7) + +#define PM1_LIMIT 16 +#define GPE0_LIMIT 28 +#define TOTAL_BITS(a) (8 * sizeof(a)) + +/* + * PCI Config Space Definitions + */ + +/* ISA Bridge D14F3 */ #define LPC_PCI_CONTROL 0x40 #define LEGACY_DMA_EN BIT(2) @@ -159,6 +271,9 @@ #define LPC_WIDEIO0_ENABLE BIT(2) #define DECODE_ALTERNATE_SIO_ENABLE BIT(1) #define DECODE_SIO_ENABLE BIT(0) +#define WIDEIO_RANGE_ERROR -1 +#define TOTAL_WIDEIO_PORTS 3 + /* Assuming word access to higher word (register 0x4a) */ #define LPC_IO_OR_MEM_DEC_EN_HIGH 0x4a #define LPC_WIDEIO2_ENABLE_H BIT(9) @@ -174,10 +289,8 @@ #define LPC_MEM_PORT1 0x4c #define LPC_MEM_PORT0 0x60 -/* - * Register 0x64 is 32-bit, composed by two 16-bit sub-registers. - * For ease of access, each sub-register is declared separetely. - */ +/* Register 0x64 is 32-bit, composed by two 16-bit sub-registers. + For ease of access, each sub-register is declared separetely. */ #define LPC_WIDEIO_GENERIC_PORT 0x64 #define LPC_WIDEIO1_GENERIC_PORT 0x66 #define ROM_ADDRESS_RANGE1_START 0x68 @@ -199,11 +312,9 @@ #define LPC_WIDEIO2_GENERIC_PORT 0x90 -/* - * LPC register 0xb8 is DWORD, here there are definitions for byte - * access. For example, bits 31-24 are accessed through byte access - * at register 0xbb (). - */ +/* LPC register 0xb8 is DWORD, here there are definitions for byte + access. For example, bits 31-24 are accessed through byte access + at register 0xbb. */ #define LPC_ROM_DMA_EC_HOST_CONTROL 0xb8 #define SPI_FROM_HOST_PREFETCH_EN BIT(24) #define SPI_FROM_USB_PREFETCH_EN BIT(23) @@ -212,7 +323,7 @@ #define PREFETCH_EN_SPI_FROM_HOST BIT(0) #define T_START_ENH BIT(3) -/* SPI Controller */ +/* SPI Controller (base address in D14F3xA0) */ #define SPI_CNTRL0 0x00 #define SPI_BUSY BIT(31) #define SPI_READ_MODE_MASK (BIT(30) | BIT(29) | BIT(18)) @@ -270,119 +381,16 @@ #define MISC_MISC_CLK_CNTL_1 0x40 #define OSCOUT1_CLK_OUTPUT_ENB BIT(2) /* 0 = Enabled, 1 = Disabled */ +/* Platform Security Processor D8F0 */ +#define PSP_MAILBOX_BAR PCI_BASE_ADDRESS_4 /* BKDG: "BAR3" */ +#define PSP_BAR_ENABLES 0x48 +#define PSP_MAILBOX_BAR_EN 0x10 + /* IO 0xcf9 - Reset control port*/ #define FULL_RST BIT(3) #define RST_CMD BIT(2) #define SYS_RST BIT(1) -/* PMx10 - Power Reset Config */ -#define PWR_RESET_CFG 0x10 -#define TOGGLE_ALL_PWR_GOOD BIT(1) - -/* XHCI_PM Registers: 0xfed81c00 */ -#define XHCI_PM_INDIRECT_INDEX 0x48 -#define XHCI_PM_INDIRECT_DATA 0x4c -#define XHCI_OVER_CURRENT_CONTROL 0x30 -#define USB_OC0 0 -#define USB_OC1 1 -#define USB_OC2 2 -#define USB_OC3 3 -#define USB_OC4 4 -#define USB_OC5 5 -#define USB_OC6 6 -#define USB_OC7 7 -#define USB_OC_DISABLE 0xf -#define USB_OC_DISABLE_ALL 0xffff -#define OC_PORT0_SHIFT 0 -#define OC_PORT1_SHIFT 4 -#define OC_PORT2_SHIFT 8 -#define OC_PORT3_SHIFT 12 - -#define EHCI_OVER_CURRENT_CONTROL 0x70 -#define EHCI_HUB_CONFIG4 0x90 -#define DEBUG_PORT_SELECT_SHIFT 16 -#define DEBUG_PORT_ENABLE BIT(18) -#define DEBUG_PORT_MASK (BIT(16) | BIT(17) | (BIT(18)) - -#define WIDEIO_RANGE_ERROR -1 -#define TOTAL_WIDEIO_PORTS 3 - -/* FCH AOAC Registers 0xfed81e00 */ -#define FCH_AOAC_D3_CONTROL_CLK_GEN 0x40 -#define FCH_AOAC_D3_CONTROL_I2C0 0x4a -#define FCH_AOAC_D3_CONTROL_I2C1 0x4c -#define FCH_AOAC_D3_CONTROL_I2C2 0x4e -#define FCH_AOAC_D3_CONTROL_I2C3 0x50 -#define FCH_AOAC_D3_CONTROL_UART0 0x56 -#define FCH_AOAC_D3_CONTROL_UART1 0x58 -#define FCH_AOAC_D3_CONTROL_AMBA 0x62 -#define FCH_AOAC_D3_CONTROL_USB2 0x64 -#define FCH_AOAC_D3_CONTROL_USB3 0x6e -/* Bit definitions for all FCH_AOAC_D3_CONTROL_* Registers */ -#define FCH_AOAC_TARGET_DEVICE_STATE (BIT(0) + BIT(1)) -#define FCH_AOAC_DEVICE_STATE BIT(2) -#define FCH_AOAC_PWR_ON_DEV BIT(3) -#define FCH_AOAC_SW_PWR_ON_RSTB BIT(4) -#define FCH_AOAC_SW_REF_CLK_OK BIT(5) -#define FCH_AOAC_SW_RST_B BIT(6) -#define FCH_AOAC_IS_SW_CONTROL BIT(7) - -#define FCH_AOAC_D3_STATE_CLK_GEN 0x41 -#define FCH_AOAC_D3_STATE_I2C0 0x4b -#define FCH_AOAC_D3_STATE_I2C1 0x4d -#define FCH_AOAC_D3_STATE_I2C2 0x4f -#define FCH_AOAC_D3_STATE_I2C3 0x51 -#define FCH_AOAC_D3_STATE_UART0 0x57 -#define FCH_AOAC_D3_STATE_UART1 0x59 -#define FCH_AOAC_D3_STATE_AMBA 0x63 -#define FCH_AOAC_D3_STATE_USB2 0x65 -#define FCH_AOAC_D3_STATE_USB3 0x6f -/* Bit definitions for all FCH_AOAC_D3_STATE_* Registers */ -#define FCH_AOAC_PWR_RST_STATE BIT(0) -#define FCH_AOAC_RST_CLK_OK_STATE BIT(1) -#define FCH_AOAC_RST_B_STATE BIT(2) -#define FCH_AOAC_DEV_OFF_GATING_STATE BIT(3) -#define FCH_AOAC_D3COLD BIT(4) -#define FCH_AOAC_CLK_OK_STATE BIT(5) -#define FCH_AOAC_STAT0 BIT(6) -#define FCH_AOAC_STAT1 BIT(7) - -#define PM1_LIMIT 16 -#define GPE0_LIMIT 28 -#define TOTAL_BITS(a) (8 * sizeof(a)) - -/* Bit definitions for MISC_MMIO_BASE register GPPClkCntrl */ -#define GPP_CLK_CNTRL 0 -#define GPP_CLK2_CLOCK_REQ_MAP_SHIFT 8 -#define GPP_CLK2_CLOCK_REQ_MAP_MASK (0xf << GPP_CLK2_CLOCK_REQ_MAP_SHIFT) -#define GPP_CLK2_CLOCK_REQ_MAP_CLK_REQ2 3 - -#define GPP_CLK0_CLOCK_REQ_MAP_SHIFT 0 -#define GPP_CLK0_CLOCK_REQ_MAP_MASK (0xf << GPP_CLK0_CLOCK_REQ_MAP_SHIFT) -#define GPP_CLK0_CLOCK_REQ_MAP_CLK_REQ0 1 - -/* Bit definitions for MISC_MMIO_BASE register MiscClkCntl1 */ -#define MISC_CGPLL_CONFIG1 0x08 -#define CG1PLL_SPREAD_SPECTRUM_ENABLE BIT(0) -#define MISC_CGPLL_CONFIG3 0x10 -#define CG1PLL_REFDIV_SHIFT 0 -#define CG1PLL_REFDIV_MASK (0x3ff << CG1PLL_REFDIV_SHIFT) -#define CG1PLL_FBDIV_SHIFT 10 -#define CG1PLL_FBDIV_MASK (0xfff << CG1PLL_FBDIV_SHIFT) -#define MISC_CGPLL_CONFIG4 0x14 -#define CG1PLL_SS_STEP_SIZE_DSFRAC_SHIFT 0 -#define CG1PLL_SS_STEP_SIZE_DSFRAC_MASK (0xffff << CG1PLL_SS_STEP_SIZE_DSFRAC_SHIFT) -#define CG1PLL_SS_AMOUNT_DSFRAC_SHIFT 16 -#define CG1PLL_SS_AMOUNT_DSFRAC_MASK (0xffff << CG1PLL_SS_AMOUNT_DSFRAC_SHIFT) -#define MISC_CGPLL_CONFIG5 0x18 -#define CG1PLL_SS_AMOUNT_NFRAC_SLIP_SHIFT 8 -#define CG1PLL_SS_AMOUNT_NFRAC_SLIP_MASK (0xf << CG1PLL_SS_AMOUNT_NFRAC_SLIP_SHIFT) -#define MISC_CGPLL_CONFIG6 0x1c -#define CG1PLL_LF_MODE_SHIFT 9 -#define CG1PLL_LF_MODE_MASK (0x1ff << CG1PLL_LF_MODE_SHIFT) -#define MISC_CLK_CNTL1 0x40 -#define CG1PLL_FBDIV_TEST BIT(26) - struct stoneyridge_aoac { int enable; int status; |