summaryrefslogtreecommitdiff
path: root/src
diff options
context:
space:
mode:
Diffstat (limited to 'src')
-rw-r--r--src/mainboard/google/hatch/variants/duffy/mainboard.c55
-rw-r--r--src/mainboard/google/hatch/variants/kaisa/mainboard.c55
2 files changed, 74 insertions, 36 deletions
diff --git a/src/mainboard/google/hatch/variants/duffy/mainboard.c b/src/mainboard/google/hatch/variants/duffy/mainboard.c
index 3f74c968b1..ceeb0c5aba 100644
--- a/src/mainboard/google/hatch/variants/duffy/mainboard.c
+++ b/src/mainboard/google/hatch/variants/duffy/mainboard.c
@@ -31,23 +31,6 @@ static void wait_for_hpd(gpio_t gpio, long timeout)
stopwatch_duration_msecs(&sw));
}
-void variant_ramstage_init(void)
-{
- static const long display_timeout_ms = 3000;
-
- /* This is reconfigured back to whatever FSP-S expects by
- gpio_configure_pads. */
- gpio_input(GPIO_HDMI_HPD);
- gpio_input(GPIO_DP_HPD);
- if (display_init_required()
- && !gpio_get(GPIO_HDMI_HPD)
- && !gpio_get(GPIO_DP_HPD)) {
- /* This has to be done before FSP-S runs. */
- if (google_chromeec_wait_for_displayport(display_timeout_ms))
- wait_for_hpd(GPIO_DP_HPD, display_timeout_ms);
- }
-}
-
/*
* For type-C chargers, set PL2 to 90% of max power to account for
* cable loss and FET Rdson loss in the path from the source.
@@ -86,6 +69,24 @@ void variant_ramstage_init(void)
* | n (U22) | 29 | .9n | .9n | x(43) |
* +-------------+-----+---------+---------+-------+
*/
+
+/*
+ * Psys_pmax considerations
+ *
+ * Given the hardware design in puff, the serial shunt resistor is 0.01ohm.
+ * The full scale of hardware PSYS signal 0.8v maps to system current 9.6A
+ * instead of real system power. The equation is shown below:
+ * PSYS = 0.8v = (0.01ohm x Iinput) x 50 (INA213, gain 50V/V) x 15k/(15k + 75k)
+ * Hence, Iinput (Amps) = 9.6A
+ * Since there is no voltage information from PSYS, different voltage input
+ * would map to different Psys_pmax settings:
+ * For Type-C 15V, the Psys_pmax sholud be 15v x 9.6A = 144W
+ * For Type-C 20V, the Psys_pmax should be 20v x 9.6A = 192W
+ * For a barral jack, the Psys_pmax should be 19v x 9.6A = 182.4W
+ */
+#define PSYS_IMAX 9600
+#define BJ_VOLTS_MV 19000
+
static void mainboard_set_power_limits(config_t *conf)
{
enum usb_chg_type type;
@@ -108,15 +109,33 @@ static void mainboard_set_power_limits(config_t *conf)
/* set minimum duty cycle */
conf->tdp_psyspl3_dutycycle = PUFF_MIN_DUTYCYCLE;
conf->tdp_pl4 = SET_PSYSPL2(psyspl2);
+ } else {
+ /* Input type is barrel jack */
+ volts_mv = BJ_VOLTS_MV;
}
+ /* voltage unit is milliVolts and current is in milliAmps */
+ conf->psys_pmax = (u16)(((u32)PSYS_IMAX * volts_mv) / 1000000);
conf->tdp_pl2_override = PUFF_PL2;
/* set psyspl2 to 90% of max adapter power */
conf->tdp_psyspl2 = SET_PSYSPL2(psyspl2);
}
-void variant_mainboard_enable(struct device *dev)
+void variant_ramstage_init(void)
{
+ static const long display_timeout_ms = 3000;
config_t *conf = config_of_soc();
+
+ /* This is reconfigured back to whatever FSP-S expects by gpio_configure_pads. */
+ gpio_input(GPIO_HDMI_HPD);
+ gpio_input(GPIO_DP_HPD);
+ if (display_init_required()
+ && !gpio_get(GPIO_HDMI_HPD)
+ && !gpio_get(GPIO_DP_HPD)) {
+ /* This has to be done before FSP-S runs. */
+ if (google_chromeec_wait_for_displayport(display_timeout_ms))
+ wait_for_hpd(GPIO_DP_HPD, display_timeout_ms);
+ }
+ /* Psys_pmax needs to be setup before FSP-S */
mainboard_set_power_limits(conf);
}
diff --git a/src/mainboard/google/hatch/variants/kaisa/mainboard.c b/src/mainboard/google/hatch/variants/kaisa/mainboard.c
index 3f74c968b1..ceeb0c5aba 100644
--- a/src/mainboard/google/hatch/variants/kaisa/mainboard.c
+++ b/src/mainboard/google/hatch/variants/kaisa/mainboard.c
@@ -31,23 +31,6 @@ static void wait_for_hpd(gpio_t gpio, long timeout)
stopwatch_duration_msecs(&sw));
}
-void variant_ramstage_init(void)
-{
- static const long display_timeout_ms = 3000;
-
- /* This is reconfigured back to whatever FSP-S expects by
- gpio_configure_pads. */
- gpio_input(GPIO_HDMI_HPD);
- gpio_input(GPIO_DP_HPD);
- if (display_init_required()
- && !gpio_get(GPIO_HDMI_HPD)
- && !gpio_get(GPIO_DP_HPD)) {
- /* This has to be done before FSP-S runs. */
- if (google_chromeec_wait_for_displayport(display_timeout_ms))
- wait_for_hpd(GPIO_DP_HPD, display_timeout_ms);
- }
-}
-
/*
* For type-C chargers, set PL2 to 90% of max power to account for
* cable loss and FET Rdson loss in the path from the source.
@@ -86,6 +69,24 @@ void variant_ramstage_init(void)
* | n (U22) | 29 | .9n | .9n | x(43) |
* +-------------+-----+---------+---------+-------+
*/
+
+/*
+ * Psys_pmax considerations
+ *
+ * Given the hardware design in puff, the serial shunt resistor is 0.01ohm.
+ * The full scale of hardware PSYS signal 0.8v maps to system current 9.6A
+ * instead of real system power. The equation is shown below:
+ * PSYS = 0.8v = (0.01ohm x Iinput) x 50 (INA213, gain 50V/V) x 15k/(15k + 75k)
+ * Hence, Iinput (Amps) = 9.6A
+ * Since there is no voltage information from PSYS, different voltage input
+ * would map to different Psys_pmax settings:
+ * For Type-C 15V, the Psys_pmax sholud be 15v x 9.6A = 144W
+ * For Type-C 20V, the Psys_pmax should be 20v x 9.6A = 192W
+ * For a barral jack, the Psys_pmax should be 19v x 9.6A = 182.4W
+ */
+#define PSYS_IMAX 9600
+#define BJ_VOLTS_MV 19000
+
static void mainboard_set_power_limits(config_t *conf)
{
enum usb_chg_type type;
@@ -108,15 +109,33 @@ static void mainboard_set_power_limits(config_t *conf)
/* set minimum duty cycle */
conf->tdp_psyspl3_dutycycle = PUFF_MIN_DUTYCYCLE;
conf->tdp_pl4 = SET_PSYSPL2(psyspl2);
+ } else {
+ /* Input type is barrel jack */
+ volts_mv = BJ_VOLTS_MV;
}
+ /* voltage unit is milliVolts and current is in milliAmps */
+ conf->psys_pmax = (u16)(((u32)PSYS_IMAX * volts_mv) / 1000000);
conf->tdp_pl2_override = PUFF_PL2;
/* set psyspl2 to 90% of max adapter power */
conf->tdp_psyspl2 = SET_PSYSPL2(psyspl2);
}
-void variant_mainboard_enable(struct device *dev)
+void variant_ramstage_init(void)
{
+ static const long display_timeout_ms = 3000;
config_t *conf = config_of_soc();
+
+ /* This is reconfigured back to whatever FSP-S expects by gpio_configure_pads. */
+ gpio_input(GPIO_HDMI_HPD);
+ gpio_input(GPIO_DP_HPD);
+ if (display_init_required()
+ && !gpio_get(GPIO_HDMI_HPD)
+ && !gpio_get(GPIO_DP_HPD)) {
+ /* This has to be done before FSP-S runs. */
+ if (google_chromeec_wait_for_displayport(display_timeout_ms))
+ wait_for_hpd(GPIO_DP_HPD, display_timeout_ms);
+ }
+ /* Psys_pmax needs to be setup before FSP-S */
mainboard_set_power_limits(conf);
}
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-27 15:12:58 +0000