diff options
Diffstat (limited to 'src')
| -rw-r--r-- | src/mainboard/google/octopus/Kconfig | 1 | ||||
| -rw-r--r-- | src/mainboard/google/octopus/variants/bip/devicetree.cb | 194 |
2 files changed, 195 insertions, 0 deletions
diff --git a/src/mainboard/google/octopus/Kconfig b/src/mainboard/google/octopus/Kconfig index 3254ec6339..79af95c238 100644 --- a/src/mainboard/google/octopus/Kconfig +++ b/src/mainboard/google/octopus/Kconfig @@ -46,6 +46,7 @@ config VARIANT_DIR config DEVICETREE string + default "variants/bip/devicetree.cb" if BOARD_GOOGLE_BIP default "variants/baseboard/devicetree.cb" config MAINBOARD_PART_NUMBER diff --git a/src/mainboard/google/octopus/variants/bip/devicetree.cb b/src/mainboard/google/octopus/variants/bip/devicetree.cb new file mode 100644 index 0000000000..860ca7933a --- /dev/null +++ b/src/mainboard/google/octopus/variants/bip/devicetree.cb @@ -0,0 +1,194 @@ +chip soc/intel/apollolake + device cpu_cluster 0 on + device lapic 0 on end + end + + register "pcie_rp_clkreq_pin[2]" = "3" # wifi/bt + # Disable unused clkreq of PCIe root ports + register "pcie_rp_clkreq_pin[0]" = "CLKREQ_DISABLED" + register "pcie_rp_clkreq_pin[1]" = "CLKREQ_DISABLED" + register "pcie_rp_clkreq_pin[3]" = "CLKREQ_DISABLED" + register "pcie_rp_clkreq_pin[4]" = "CLKREQ_DISABLED" + register "pcie_rp_clkreq_pin[5]" = "CLKREQ_DISABLED" + + # Set de-emphasis to disabled for PCIE WiFI (Thunderpeak) + # as it is required for detection + register "pcie_rp_deemphasis_enable[2]" = "0" + # Set de-emphasis to default (enabled) for remaining ports + register "pcie_rp_deemphasis_enable[0]" = "1" + register "pcie_rp_deemphasis_enable[1]" = "1" + register "pcie_rp_deemphasis_enable[3]" = "1" + register "pcie_rp_deemphasis_enable[4]" = "1" + register "pcie_rp_deemphasis_enable[5]" = "1" + + # GPIO for PERST_0 (WLAN_PE_RST) + register "prt0_gpio" = "GPIO_164" + + # GPE configuration + # Note that GPE events called out in ASL code rely on this + # route, i.e., if this route changes then the affected GPE + # offset bits also need to be changed. This sets the PMC register + # GPE_CFG fields. + register "gpe0_dw1" = "PMC_GPE_NW_63_32" + register "gpe0_dw2" = "PMC_GPE_N_95_64" + register "gpe0_dw3" = "PMC_GPE_NW_31_0" + + # PL1 override 8000 mW: Due to error in the energy calculation for + # current VR solution. Experiments show that SoC TDP max (6W) can + # be reached when RAPL PL1 is set to 8W. + register "tdp_pl1_override_mw" = "8000" + # Set RAPL PL2 to 15W. + register "tdp_pl2_override_mw" = "15000" + + # Minimum SLP S3 assertion width 28ms. + register "slp_s3_assertion_width_usecs" = "28000" + + # Enable lpss s0ix + register "lpss_s0ix_enable" = "1" + + # Enable DPTF + register "dptf_enable" = "1" + + # Enable Audio Clock and Power gating + register "hdaudio_clk_gate_enable" = "1" + register "hdaudio_pwr_gate_enable" = "1" + register "hdaudio_bios_config_lockdown" = "1" + + # digitizer at 400kHz + register "i2c[0]" = "{ + .speed = I2C_SPEED_FAST, + .rise_time_ns = 152, + .fall_time_ns = 30, + }" + + # Enable I2C5 for audio codec at 400kHz + register "i2c[5]" = "{ + .speed = I2C_SPEED_FAST, + .rise_time_ns = 104, + .fall_time_ns = 52, + }" + + # trackpad at 400kHz + register "i2c[6]" = "{ + .speed = I2C_SPEED_FAST, + .rise_time_ns = 114, + .fall_time_ns = 164, + .data_hold_time_ns = 350, + }" + + # touchscreen at 400kHz + register "i2c[7]" = "{ + .speed = I2C_SPEED_FAST, + .rise_time_ns = 76, + .fall_time_ns = 164, + }" + + # Use GSPI0 for cr50 TPM. Early init is required to set up a BAR for TPM + # communication before memory is up. + register "gspi[0]" = "{ + .speed_mhz = 1, + .early_init = 1, + }" + + register "pnp_settings" = "PNP_PERF_POWER" + + device domain 0 on + device pci 00.0 on end # - Host Bridge + device pci 00.1 on end # - DPTF + device pci 00.2 off end # - NPK + device pci 02.0 on end # - Gen + device pci 03.0 on end # - Iunit + device pci 0c.0 on end # - CNVi + device pci 0d.0 on end # - P2SB + device pci 0d.1 on end # - PMC + device pci 0d.2 on end # - Fast SPI + device pci 0d.3 on end # - Shared SRAM + device pci 0e.0 on + chip drivers/generic/max98357a + register "sdmode_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPIO_91)" + register "sdmode_delay" = "5" + device generic 0 on end + end + end # - Audio + device pci 0f.0 on end # - Heci1 + device pci 0f.1 on end # - Heci2 + device pci 0f.2 on end # - Heci3 + device pci 11.0 off end # - ISH + device pci 12.0 off end # - SATA + device pci 13.0 on + chip drivers/intel/wifi + device pci 00.0 on end + end + end # - PCIe-A 0 Onboard M2 Slot(Wifi) + device pci 13.1 off end # - PCIe-A 1 + device pci 13.2 off end # - PCIe-A 2 + device pci 13.3 off end # - PCIe-A 3 + device pci 14.0 off end # - PCIe-B 0 + device pci 14.1 off end # - PCIe-B 1 + device pci 15.0 on end # - XHCI + device pci 15.1 off end # - XDCI + device pci 16.0 on + chip drivers/i2c/hid + register "generic.hid" = ""WCOM50C1"" + register "generic.desc" = ""WCOM Digitizer"" + register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPIO_139_IRQ)" + register "generic.reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPIO_140)" + register "generic.has_power_resource" = "1" + register "hid_desc_reg_offset" = "0x1" + device i2c 0x9 on end + end + end # - I2C 0 + device pci 16.1 on end # - I2C 1 + device pci 16.2 on end # - I2C 2 + device pci 16.3 on end # - I2C 3 + device pci 17.0 on end # - I2C 4 + device pci 17.1 on end # - I2C 5 + device pci 17.2 on + chip drivers/i2c/generic + register "hid" = ""ELAN0000"" + register "desc" = ""ELAN Touchpad"" + register "irq" = "ACPI_IRQ_EDGE_LOW(GPIO_135_IRQ)" + register "wake" = "GPE0_DW2_02" + register "probed" = "1" + device i2c 15 on end + end + end # - I2C 6 + device pci 17.3 on + chip drivers/i2c/generic + register "hid" = ""ELAN0001"" + register "desc" = ""ELAN Touchscreen"" + register "irq" = "ACPI_IRQ_EDGE_LOW(GPIO_212_IRQ)" + register "probed" = "1" + register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPIO_105)" + register "reset_delay_ms" = "20" + register "enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPIO_213)" + register "enable_delay_ms" = "1" + register "has_power_resource" = "1" + device i2c 10 on end + end + end # - I2C 7 + device pci 18.0 on end # - UART 0 + device pci 18.1 off end # - UART 1 + device pci 18.2 on end # - UART 2 + device pci 18.3 off end # - UART 3 + device pci 19.0 on + chip drivers/spi/acpi + register "hid" = "ACPI_DT_NAMESPACE_HID" + register "compat_string" = ""google,cr50"" + register "irq" = "ACPI_IRQ_EDGE_LOW(GPIO_63_IRQ)" + device spi 0 on end + end + end # - GSPI 0 + device pci 19.1 off end # - SPI 1 + device pci 19.2 on end # - SPI 2 + device pci 1a.0 on end # - PWM + device pci 1c.0 on end # - eMMC + device pci 1e.0 off end # - SDIO + device pci 1f.0 on + chip ec/google/chromeec + device pnp 0c09.0 on end + end + end # - ESPI + device pci 1f.1 on end # - SMBUS + end +end |