summaryrefslogtreecommitdiff
path: root/src/vendorcode
diff options
context:
space:
mode:
Diffstat (limited to 'src/vendorcode')
-rw-r--r--src/vendorcode/amd/agesa/f14/gcccar.inc110
-rw-r--r--src/vendorcode/amd/agesa/f15tn/gcccar.inc130
-rw-r--r--src/vendorcode/amd/agesa/f16kb/gcccar.inc69
-rw-r--r--src/vendorcode/amd/pi/00670F00/binaryPI/gcccar.inc70
-rw-r--r--src/vendorcode/amd/pi/00730F01/binaryPI/gcccar.inc76
5 files changed, 187 insertions, 268 deletions
diff --git a/src/vendorcode/amd/agesa/f14/gcccar.inc b/src/vendorcode/amd/agesa/f14/gcccar.inc
index 95dd74d6cb..ad9ff6ad34 100644
--- a/src/vendorcode/amd/agesa/f14/gcccar.inc
+++ b/src/vendorcode/amd/agesa/f14/gcccar.inc
@@ -245,7 +245,6 @@ MSR_MASK = ((1 << MTRR_DEF_TYPE_EN)+(1 << MTRR_DEF_TYPE_FIX_EN))
* SI[31:27]= reserved, =0
****************************************************************************/
.macro GET_NODE_ID_CORE_ID
- LOCAL node_core_exit
mov $-1, %si
GET_NODE_ID_CORE_ID_F10
@@ -256,16 +255,16 @@ MSR_MASK = ((1 << MTRR_DEF_TYPE_EN)+(1 << MTRR_DEF_TYPE_FIX_EN))
* Check for unrecognized Family
*/
cmp $-1, %si # Has family (node/core) already been discovered?
- jnz node_core_exit # Br if yes
+ jnz node_core_exit\@ # Br if yes
mov $((1 << FLAG_UNKNOWN_FAMILY)+(1 << FLAG_IS_PRIMARY)), %esi # No, Set error code, Only let BSP continue
mov $APIC_BASE_ADDRESS, %ecx # MSR:0000_001B
_RDMSR
bt $APIC_BSC, %eax # Is this the BSC?
- jc node_core_exit # Br if yes
+ jc node_core_exit\@ # Br if yes
hlt # Kill APs
-node_core_exit:
+node_core_exit\@:
.endm
@@ -297,12 +296,11 @@ node_core_exit:
# * No INVD or WBINVD, no exceptions, page faults or interrupts
****************************************************************************/
.macro AMD_ENABLE_STACK_FAMILY_HOOK_F10
- LOCAL fam10_enable_stack_hook_exit
AMD_CPUID $CPUID_MODEL
shr $20, %eax # AL = cpu extended family
cmp $0x01, %al # Is this family 10h?
- jnz fam10_enable_stack_hook_exit # Br if no
+ jnz fam10_enable_stack_hook_exit\@ # Br if no
mov $DC_CFG, %ecx # MSR:C001_1022
_RDMSR
@@ -333,7 +331,7 @@ node_core_exit:
fam10_skipClearingBit4:
mov %esi, %eax # load core#
or %al, %al # If (BSP)
- jne fam10_enable_stack_hook_exit
+ jne fam10_enable_stack_hook_exit\@
mov $PERF_COUNTER3, %ecx # Select performance counter three
# to count number of CAR evictions
xor %eax, %eax # Initialize the lower part of the counter to zero
@@ -350,7 +348,7 @@ fam10_skipClearingBit4:
bts $EVENT_ENABLE, %eax # Enable it
_WRMSR # Save it
-fam10_enable_stack_hook_exit:
+fam10_enable_stack_hook_exit\@:
.endm
/****************************************************************************
@@ -378,7 +376,6 @@ fam10_enable_stack_hook_exit:
*****************************************************************************/
.macro AMD_DISABLE_STACK_FAMILY_HOOK_F10
- LOCAL fam10_disable_stack_hook_exit
AMD_CPUID $CPUID_MODEL
shr $20, %eax # AL = cpu extended family
@@ -448,22 +445,20 @@ fam10_disable_stack_hook_exit:
*****************************************************************************/
.macro GET_NODE_ID_CORE_ID_F10
- LOCAL node_core_f10_exit
- LOCAL node_core_f10_AP
cmp $-1, %si # Has node/core already been discovered?
- jnz node_core_f10_exit # Br if yes
+ jnz node_core_f10_exit\@ # Br if yes
AMD_CPUID $CPUID_MODEL
shr $20, %eax # AL = cpu extended family
cmp $0x01, %al # Is this family 10h?
- jnz node_core_f10_exit # Br if no
+ jnz node_core_f10_exit\@ # Br if no
xor %esi, %esi # Assume BSC, clear flags
mov $APIC_BASE_ADDRESS, %ecx # MSR:0000_001B
_RDMSR
bt $APIC_BSC, %eax # Is this the BSC?
- jnc node_core_f10_AP # Br if no
+ jnc node_core_f10_AP\@ # Br if no
# This is the BSP.
# Enable routing tables on BSP (just in case the HT init code has not yet enabled them)
@@ -476,7 +471,7 @@ fam10_disable_stack_hook_exit:
out %eax, %dx
jmp 1f #
-node_core_f10_AP:
+node_core_f10_AP\@:
#
# This is an AP. Routing tables have been enabled by the HT Init process.
# Also, the MailBox register was set by the BSP during early init
@@ -532,7 +527,7 @@ node_core_f10_AP:
mov %eax, %esi # ESI = return value
1:
bts $FLAG_IS_PRIMARY, %esi # all Family 10h cores are primary
-node_core_f10_exit:
+node_core_f10_exit\@:
.endm
@@ -564,12 +559,11 @@ node_core_f10_exit:
* * No INVD or WBINVD, no exceptions, page faults or interrupts
*****************************************************************************/
.macro AMD_ENABLE_STACK_FAMILY_HOOK_F12
- LOCAL fam12_enable_stack_hook_exit
AMD_CPUID $CPUID_MODEL
shr $20, %eax # AL = cpu extended family
cmp $0x03, %al # Is this family 12h?
- jnz fam12_enable_stack_hook_exit # Br if no
+ jnz fam12_enable_stack_hook_exit\@ # Br if no
mov $DC_CFG, %ecx # MSR:C001_1022
_RDMSR
@@ -601,7 +595,7 @@ fam12_skipClearingBit4:
bts $CL_FLUSH_SERIALIZE, %eax # Serialize all CL Flush actions
_WRMSR
-fam12_enable_stack_hook_exit:
+fam12_enable_stack_hook_exit\@:
.endm
/*****************************************************************************
@@ -627,12 +621,11 @@ fam12_enable_stack_hook_exit:
* * MSRC001_1029[ClflushSerialize]=0
*****************************************************************************/
.macro AMD_DISABLE_STACK_FAMILY_HOOK_F12
- LOCAL fam12_disable_stack_hook_exit
AMD_CPUID $CPUID_MODEL
shr $20, %eax # AL = cpu extended family
cmp $0x03, %al # Is this family 12h?
- jnz fam12_disable_stack_hook_exit # Br if no
+ jnz fam12_disable_stack_hook_exit\@ # Br if no
mov $DC_CFG, %ecx # MSR:C001_1022
_RDMSR
@@ -673,7 +666,7 @@ fam12_enable_stack_hook_exit:
# End critical sequence in which EAX, BX, ECX, and EDX must be preserved.
#--------------------------------------------------------------------------
-fam12_disable_stack_hook_exit:
+fam12_disable_stack_hook_exit\@:
.endm
/*****************************************************************************
@@ -690,20 +683,19 @@ fam12_disable_stack_hook_exit:
*****************************************************************************/
.macro GET_NODE_ID_CORE_ID_F12
- LOCAL node_core_f12_exit
cmp $-1, %si # Has node/core already been discovered?
- jnz node_core_f12_exit # Br if yes
+ jnz node_core_f12_exit\@ # Br if yes
AMD_CPUID $CPUID_MODEL
shr $20, %eax # AL = cpu extended family
cmp $0x03, %al # Is this family 12h?
- jnz node_core_f12_exit # Br if no
+ jnz node_core_f12_exit\@ # Br if no
shr $24, %ebx # CPUID_0000_0001_EBX[31:24]: initial local APIC physical ID
bts $FLAG_IS_PRIMARY, %ebx # all family 12h cores are primary
mov %ebx, %esi # ESI = Node#=0, core number
-node_core_f12_exit:
+node_core_f12_exit\@:
.endm
/*****************************************************************************
@@ -730,12 +722,11 @@ node_core_f12_exit:
* * No INVD or WBINVD, no exceptions, page faults or interrupts
*****************************************************************************/
.macro AMD_ENABLE_STACK_FAMILY_HOOK_F14
- LOCAL fam14_enable_stack_hook_exit
AMD_CPUID $CPUID_MODEL
shr $20, %eax # AL = cpu extended family
cmp $0x05, %al # Is this family 14h?
- jnz fam14_enable_stack_hook_exit # Br if no
+ jnz fam14_enable_stack_hook_exit\@ # Br if no
mov $DC_CFG, %ecx # MSR:C001_1022
_RDMSR
@@ -760,7 +751,7 @@ node_core_f12_exit:
_WRMSR
fam14_skipClearingBit4: # Keeping this label
-fam14_enable_stack_hook_exit:
+fam14_enable_stack_hook_exit\@:
.endm
/*****************************************************************************
@@ -783,12 +774,11 @@ fam14_enable_stack_hook_exit:
* * MSRC001_1022[DIS_HW_PF]=0.
*****************************************************************************/
.macro AMD_DISABLE_STACK_FAMILY_HOOK_F14
- LOCAL fam14_disable_stack_hook_exit
AMD_CPUID $CPUID_MODEL
shr $20, %eax # AL = cpu extended family
cmp $0x05, %al # Is this family 14h?
- jnz fam14_disable_stack_hook_exit # Br if no
+ jnz fam14_disable_stack_hook_exit\@ # Br if no
mov $LS_CFG, %ecx # MSR:C001_1020
_RDMSR
@@ -821,7 +811,7 @@ fam14_enable_stack_hook_exit:
# End critical sequence in which EAX, BX, ECX, and EDX must be preserved.
#--------------------------------------------------------------------------
-fam14_disable_stack_hook_exit:
+fam14_disable_stack_hook_exit\@:
.endm
/*****************************************************************************
@@ -838,24 +828,23 @@ fam14_disable_stack_hook_exit:
*****************************************************************************/
.macro GET_NODE_ID_CORE_ID_F14
- LOCAL node_core_f14_exit
cmp $-1, %si # Has node/core already been discovered?
- jnz node_core_f14_exit # Br if yes
+ jnz node_core_f14_exit\@ # Br if yes
AMD_CPUID $CPUID_MODEL
shr $20, %eax # AL = cpu extended family
cmp $0x05, %al # Is this family 14h?
- jnz node_core_f14_exit # Br if no
+ jnz node_core_f14_exit\@ # Br if no
xor %esi, %esi # Node must be 0
bts $FLAG_IS_PRIMARY, %esi # all family 14h cores are primary
mov $APIC_BASE_ADDRESS, %ecx # MSR:0000_001B
_RDMSR
bt $APIC_BSC, %eax # Is this the BSC?
- jc node_core_f14_exit # Br if yes
+ jc node_core_f14_exit\@ # Br if yes
inc %si # Set core to 1
-node_core_f14_exit:
+node_core_f14_exit\@:
.endm
@@ -885,12 +874,11 @@ node_core_f14_exit:
* * No INVD or WBINVD, no exceptions, page faults or interrupts
*****************************************************************************/
.macro AMD_ENABLE_STACK_FAMILY_HOOK_F15
- LOCAL fam15_enable_stack_hook_exit
AMD_CPUID $CPUID_MODEL
shr $20, %eax # AL = cpu extended family
cmp $0x06, %al # Is this family 15h?
- jnz fam15_enable_stack_hook_exit # Br if no
+ jnz fam15_enable_stack_hook_exit\@ # Br if no
bt $FLAG_STACK_REENTRY , %esi # Check if stack has already been set
jc fam15_skipClearingBit4
@@ -921,7 +909,7 @@ fam15_skipClearingBit4:
btr $(COMBINE_CR0_CD - 32), %edx # Clear CombineCr0Cd bit
_WRMSR
-fam15_enable_stack_hook_exit:
+fam15_enable_stack_hook_exit\@:
.endm
@@ -946,13 +934,12 @@ fam15_enable_stack_hook_exit:
* * MSRC001_1022[DIS_HW_PF]=0
*****************************************************************************/
.macro AMD_DISABLE_STACK_FAMILY_HOOK_F15
- LOCAL fam15_disable_stack_hook_exit
AMD_CPUID $CPUID_MODEL
mov %eax, %ebx # Save revision info to EBX
shr $20, %eax # AL = cpu extended family
cmp $0x06, %al # Is this family 15h?
- jnz fam15_disable_stack_hook_exit # Br if no
+ jnz fam15_disable_stack_hook_exit\@ # Br if no
mov $LS_CFG, %ecx # MSR:C001_1020
#.if (ebx != 00600F00h) ; Is this rev A0?
@@ -1005,7 +992,7 @@ fam15_enable_stack_hook_exit:
bts $(COMBINE_CR0_CD - 32), %edx # Set CombineCr0Cd bit
_WRMSR
-fam15_disable_stack_hook_exit:
+fam15_disable_stack_hook_exit\@:
.endm
@@ -1023,23 +1010,20 @@ fam15_disable_stack_hook_exit:
*****************************************************************************/
.macro GET_NODE_ID_CORE_ID_F15
- LOCAL node_core_f15_exit
- LOCAL node_core_f15_AP
- LOCAL node_core_f15_shared
cmp $-1, %si # Has node/core already been discovered?
- jnz node_core_f15_exit # Br if yes
+ jnz node_core_f15_exit\@ # Br if yes
AMD_CPUID $CPUID_MODEL
shr $20, %eax # AL = cpu extended family
cmp $06, %al # Is this family 15h?
- jnz node_core_f15_exit # Br if no
+ jnz node_core_f15_exit\@ # Br if no
xor %esi, %esi # Assume BSC, clear local flags
mov $APIC_BASE_ADDRESS, %ecx # MSR:0000_001B
_RDMSR
bt $APIC_BSC, %eax # Is this the BSC?
- jnc node_core_f15_AP # Br if no
+ jnc node_core_f15_AP\@ # Br if no
# This is the BSP.
# Enable routing tables on BSP (just in case the HT init code has not yet enabled them)
@@ -1050,9 +1034,9 @@ fam15_disable_stack_hook_exit:
in %dx, %eax
btr $0, %eax # Set LinkInitializationControl[RouteTblDis] = 0
out %eax, %dx
- jmp node_core_f15_shared #
+ jmp node_core_f15_shared\@ #
-node_core_f15_AP:
+node_core_f15_AP\@:
#
# This is an AP. Routing tables have been enabled by the HT Init process.
# Also, the MailBox register was set by the BSP during early init
@@ -1110,7 +1094,7 @@ node_core_f15_AP:
#
# determine if this core shares MTRRs
#
-node_core_f15_shared:
+node_core_f15_shared\@:
mov $0x8000C580, %eax # Compute Unit Status
mov %si, %bx
shl $3, %bh # Move node# to PCI Dev# field
@@ -1173,7 +1157,7 @@ node_core_f15_shared:
#.endif
2:
-node_core_f15_exit:
+node_core_f15_exit\@:
.endm
@@ -1245,10 +1229,6 @@ node_core_f15_exit:
.macro AMD_ENABLE_STACK
# These are local labels. Declared so linker doesn't cause 'redefined label' errors
- LOCAL SetupStack
- LOCAL Real16bMode
- LOCAL Protected32Mode
- LOCAL ClearTheStack
# Note that SS:ESP will be default stack. Note that this stack
# routine will not be used after memory has been initialized. Because
@@ -1262,14 +1242,14 @@ node_core_f15_exit:
# It is =0 after reset; CAR setup sets it to enable the MTRRs
mov %cr0, %eax
test $CR0_MASK, %eax # Is cache disabled? (CD & NW bits)
- jnz SetupStack # Jump if yes
+ jnz SetupStack\@ # Jump if yes
mov $AMD_MTRR_DEFTYPE, %ecx # MSR:0000_02FF
_RDMSR
test $MSR_MASK, %eax # Are the default types enabled? (MTRR_DEF_TYPE_EN + MTRR_DEF_TYPE_FIX_EN)
- jz SetupStack # Jump if no
+ jz SetupStack\@ # Jump if no
or $FLAG_STACK_REENTRY, %esi # Bit25, indicate stack has already been initialized
-SetupStack:
+SetupStack\@:
# Set node to map the first 16MB to node 0# 0000_0000 to 00FF_FFFF as DRAM
mov %esi, %ebx # Get my Node/Core info
xor %bl, %bl
@@ -1500,12 +1480,12 @@ SetupStack:
mov %cr0, %ecx # Check for 32-bit protect mode
bt $CR0_PE, %ecx #
#.if (!carry?) # PE=0 means real mode
- jc Protected32Mode
+ jc Protected32Mode\@
mov %cs, %cx # PE=1
cmp $0x0D000, %cx # Check for CS
- jb Protected32Mode # If CS < D000, it is a selector instead of a segment
+ jb Protected32Mode\@ # If CS < D000, it is a selector instead of a segment
# alter SS:ESP for 16b Real Mode:
-Real16bMode:
+Real16bMode\@:
mov %edi, %eax
shr $4, %eax # Create a Real Mode segment for ss, ds, es
mov %ax, %ss
@@ -1520,7 +1500,7 @@ Real16bMode:
# Default is to use Protected 32b Mode
#.endif
;
-Protected32Mode:
+Protected32Mode\@:
#
# Clear The Stack
# Now that we have set the location and the MTRRs, initialize the cache by
@@ -1533,7 +1513,7 @@ Protected32Mode:
# edi - address of start of stack block
#
-ClearTheStack: # Stack base is in SS, stack pointer is in ESP
+ClearTheStack\@: # Stack base is in SS, stack pointer is in ESP
shr $2, %ebx # ebx = stack block size in dwords
mov %bx, %cx #
# Check our flags - Don't clear an existing stack
diff --git a/src/vendorcode/amd/agesa/f15tn/gcccar.inc b/src/vendorcode/amd/agesa/f15tn/gcccar.inc
index fb49c17c59..6a3ebaf7f8 100644
--- a/src/vendorcode/amd/agesa/f15tn/gcccar.inc
+++ b/src/vendorcode/amd/agesa/f15tn/gcccar.inc
@@ -286,7 +286,6 @@ MSR_MASK = ((1 << MTRR_DEF_TYPE_EN)+(1 << MTRR_DEF_TYPE_FIX_EN))
* SI[31:27]= reserved, =0
****************************************************************************/
.macro GET_NODE_ID_CORE_ID
- LOCAL node_core_exit
mov $-1, %si
GET_NODE_ID_CORE_ID_F10
@@ -297,16 +296,16 @@ MSR_MASK = ((1 << MTRR_DEF_TYPE_EN)+(1 << MTRR_DEF_TYPE_FIX_EN))
* Check for unrecognized Family
*/
cmp $-1, %si # Has family (node/core) already been discovered?
- jnz node_core_exit # Br if yes
+ jnz node_core_exit\@ # Br if yes
mov $((1 << FLAG_UNKNOWN_FAMILY)+(1 << FLAG_IS_PRIMARY)), %esi # No, Set error code, Only let BSP continue
mov $APIC_BASE_ADDRESS, %ecx # MSR:0000_001B
_RDMSR
bt $APIC_BSC, %eax # Is this the BSC?
- jc node_core_exit # Br if yes
+ jc node_core_exit\@ # Br if yes
hlt # Kill APs
-node_core_exit:
+node_core_exit\@:
.endm
@@ -338,12 +337,11 @@ node_core_exit:
# * No INVD or WBINVD, no exceptions, page faults or interrupts
****************************************************************************/
.macro AMD_ENABLE_STACK_FAMILY_HOOK_F10
- LOCAL fam10_enable_stack_hook_exit
AMD_CPUID $CPUID_MODEL
shr $20, %eax # AL = cpu extended family
cmp $0x01, %al # Is this family 10h?
- jnz fam10_enable_stack_hook_exit # Br if no
+ jnz fam10_enable_stack_hook_exit\@ # Br if no
mov $DC_CFG, %ecx # MSR:C001_1022
_RDMSR
@@ -374,7 +372,7 @@ node_core_exit:
fam10_skipClearingBit4:
mov %esi, %eax # load core#
or %al, %al # If (BSP)
- jne fam10_enable_stack_hook_exit
+ jne fam10_enable_stack_hook_exit\@
mov $PERF_COUNTER3, %ecx # Select performance counter three
# to count number of CAR evictions
xor %eax, %eax # Initialize the lower part of the counter to zero
@@ -391,7 +389,7 @@ fam10_skipClearingBit4:
bts $EVENT_ENABLE, %eax # Enable it
_WRMSR # Save it
-fam10_enable_stack_hook_exit:
+fam10_enable_stack_hook_exit\@:
.endm
/****************************************************************************
@@ -419,12 +417,11 @@ fam10_enable_stack_hook_exit:
*****************************************************************************/
.macro AMD_DISABLE_STACK_FAMILY_HOOK_F10
- LOCAL fam10_disable_stack_hook_exit
AMD_CPUID $CPUID_MODEL
shr $20, %eax # AL = cpu extended family
cmp $0x01, %al # Is this family 10h?
- jnz fam10_disable_stack_hook_exit # Br if no
+ jnz fam10_disable_stack_hook_exit\@ # Br if no
mov $DC_CFG, %ecx # MSR:C001_1022
_RDMSR
@@ -465,14 +462,14 @@ fam10_enable_stack_hook_exit:
mov $PERF_CONTROL3, %ecx # Select the event control three
_RDMSR # Retrieve the current value
btc $EVENT_ENABLE, %eax # Is event enable, complement it as well
- jnc fam10_disable_stack_hook_exit # No
+ jnc fam10_disable_stack_hook_exit\@ # No
cmp $CONFIG_EVENT_L, %ax # Is the lower part of event set to capture the CAR Corruption
- jne fam10_disable_stack_hook_exit # No
+ jne fam10_disable_stack_hook_exit\@ # No
cmp $CONFIG_EVENT_H, %dl # Is the upper part of event set to capture the CAR Corruption
- jne fam10_disable_stack_hook_exit # No
+ jne fam10_disable_stack_hook_exit\@ # No
_WRMSR # Disable the event
-fam10_disable_stack_hook_exit:
+fam10_disable_stack_hook_exit\@:
.endm
/****************************************************************************
@@ -489,22 +486,20 @@ fam10_disable_stack_hook_exit:
*****************************************************************************/
.macro GET_NODE_ID_CORE_ID_F10
- LOCAL node_core_f10_exit
- LOCAL node_core_f10_AP
cmp $-1, %si # Has node/core already been discovered?
- jnz node_core_f10_exit # Br if yes
+ jnz node_core_f10_exit\@ # Br if yes
AMD_CPUID $CPUID_MODEL
shr $20, %eax # AL = cpu extended family
cmp $0x01, %al # Is this family 10h?
- jnz node_core_f10_exit # Br if no
+ jnz node_core_f10_exit\@ # Br if no
xor %esi, %esi # Assume BSC, clear flags
mov $APIC_BASE_ADDRESS, %ecx # MSR:0000_001B
_RDMSR
bt $APIC_BSC, %eax # Is this the BSC?
- jnc node_core_f10_AP # Br if no
+ jnc node_core_f10_AP\@ # Br if no
# This is the BSP.
# Enable routing tables on BSP (just in case the HT init code has not yet enabled them)
@@ -517,7 +512,7 @@ fam10_disable_stack_hook_exit:
out %eax, %dx
jmp 1f #
-node_core_f10_AP:
+node_core_f10_AP\@:
#
# This is an AP. Routing tables have been enabled by the HT Init process.
# Also, the MailBox register was set by the BSP during early init
@@ -573,7 +568,7 @@ node_core_f10_AP:
mov %eax, %esi # ESI = return value
1:
bts $FLAG_IS_PRIMARY, %esi # all Family 10h cores are primary
-node_core_f10_exit:
+node_core_f10_exit\@:
.endm
/*****************************************************************************
@@ -604,12 +599,11 @@ node_core_f10_exit:
* * No INVD or WBINVD, no exceptions, page faults or interrupts
*****************************************************************************/
.macro AMD_ENABLE_STACK_FAMILY_HOOK_F12
- LOCAL fam12_enable_stack_hook_exit
AMD_CPUID $CPUID_MODEL
shr $20, %eax # AL = cpu extended family
cmp $0x03, %al # Is this family 12h?
- jnz fam12_enable_stack_hook_exit # Br if no
+ jnz fam12_enable_stack_hook_exit\@ # Br if no
mov $DC_CFG, %ecx # MSR:C001_1022
_RDMSR
@@ -641,7 +635,7 @@ fam12_skipClearingBit4:
bts $CL_FLUSH_SERIALIZE, %eax # Serialize all CL Flush actions
_WRMSR
-fam12_enable_stack_hook_exit:
+fam12_enable_stack_hook_exit\@:
.endm
/*****************************************************************************
@@ -667,12 +661,11 @@ fam12_enable_stack_hook_exit:
* * MSRC001_1029[ClflushSerialize]=0
*****************************************************************************/
.macro AMD_DISABLE_STACK_FAMILY_HOOK_F12
- LOCAL fam12_disable_stack_hook_exit
AMD_CPUID $CPUID_MODEL
shr $20, %eax # AL = cpu extended family
cmp $0x03, %al # Is this family 12h?
- jnz fam12_disable_stack_hook_exit # Br if no
+ jnz fam12_disable_stack_hook_exit\@ # Br if no
mov $DC_CFG, %ecx # MSR:C001_1022
_RDMSR
@@ -713,7 +706,7 @@ fam12_enable_stack_hook_exit:
# End critical sequence in which EAX, BX, ECX, and EDX must be preserved.
#--------------------------------------------------------------------------
-fam12_disable_stack_hook_exit:
+fam12_disable_stack_hook_exit\@:
.endm
/*****************************************************************************
@@ -730,20 +723,19 @@ fam12_disable_stack_hook_exit:
*****************************************************************************/
.macro GET_NODE_ID_CORE_ID_F12
- LOCAL node_core_f12_exit
cmp $-1, %si # Has node/core already been discovered?
- jnz node_core_f12_exit # Br if yes
+ jnz node_core_f12_exit\@ # Br if yes
AMD_CPUID $CPUID_MODEL
shr $20, %eax # AL = cpu extended family
cmp $0x03, %al # Is this family 12h?
- jnz node_core_f12_exit # Br if no
+ jnz node_core_f12_exit\@ # Br if no
shr $24, %ebx # CPUID_0000_0001_EBX[31:24]: initial local APIC physical ID
bts $FLAG_IS_PRIMARY, %ebx # all family 12h cores are primary
mov %ebx, %esi # ESI = Node#=0, core number
-node_core_f12_exit:
+node_core_f12_exit\@:
.endm
/*****************************************************************************
@@ -770,12 +762,11 @@ node_core_f12_exit:
* * No INVD or WBINVD, no exceptions, page faults or interrupts
*****************************************************************************/
.macro AMD_ENABLE_STACK_FAMILY_HOOK_F14
- LOCAL fam14_enable_stack_hook_exit
AMD_CPUID $CPUID_MODEL
shr $20, %eax # AL = cpu extended family
cmp $0x05, %al # Is this family 14h?
- jnz fam14_enable_stack_hook_exit # Br if no
+ jnz fam14_enable_stack_hook_exit\@ # Br if no
mov $DC_CFG, %ecx # MSR:C001_1022
_RDMSR
@@ -800,7 +791,7 @@ node_core_f12_exit:
_WRMSR
fam14_skipClearingBit4: # Keeping this label
-fam14_enable_stack_hook_exit:
+fam14_enable_stack_hook_exit\@:
.endm
/*****************************************************************************
@@ -823,12 +814,11 @@ fam14_enable_stack_hook_exit:
* * MSRC001_1022[DIS_HW_PF]=0.
*****************************************************************************/
.macro AMD_DISABLE_STACK_FAMILY_HOOK_F14
- LOCAL fam14_disable_stack_hook_exit
AMD_CPUID $CPUID_MODEL
shr $20, %eax # AL = cpu extended family
cmp $0x05, %al # Is this family 14h?
- jnz fam14_disable_stack_hook_exit # Br if no
+ jnz fam14_disable_stack_hook_exit\@ # Br if no
mov $LS_CFG, %ecx # MSR:C001_1020
_RDMSR
@@ -861,7 +851,7 @@ fam14_enable_stack_hook_exit:
# End critical sequence in which EAX, BX, ECX, and EDX must be preserved.
#--------------------------------------------------------------------------
-fam14_disable_stack_hook_exit:
+fam14_disable_stack_hook_exit\@:
.endm
/*****************************************************************************
@@ -878,24 +868,23 @@ fam14_disable_stack_hook_exit:
*****************************************************************************/
.macro GET_NODE_ID_CORE_ID_F14
- LOCAL node_core_f14_exit
cmp $-1, %si # Has node/core already been discovered?
- jnz node_core_f14_exit # Br if yes
+ jnz node_core_f14_exit\@ # Br if yes
AMD_CPUID $CPUID_MODEL
shr $20, %eax # AL = cpu extended family
cmp $0x05, %al # Is this family 14h?
- jnz node_core_f14_exit # Br if no
+ jnz node_core_f14_exit\@ # Br if no
xor %esi, %esi # Node must be 0
bts $FLAG_IS_PRIMARY, %esi # all family 14h cores are primary
mov $APIC_BASE_ADDRESS, %ecx # MSR:0000_001B
_RDMSR
bt $APIC_BSC, %eax # Is this the BSC?
- jc node_core_f14_exit # Br if yes
+ jc node_core_f14_exit\@ # Br if yes
inc %si # Set core to 1
-node_core_f14_exit:
+node_core_f14_exit\@:
.endm
/*****************************************************************************
@@ -923,13 +912,12 @@ node_core_f14_exit:
* * No INVD or WBINVD, no exceptions, page faults or interrupts
*****************************************************************************/
.macro AMD_ENABLE_STACK_FAMILY_HOOK_F15
- LOCAL fam15_enable_stack_hook_exit
AMD_CPUID $CPUID_MODEL
mov %eax, %ebx # Save revision info to EBX
shr $20, %eax # AL = cpu extended family
cmp $0x06, %al # Is this family 15h?
- jnz fam15_enable_stack_hook_exit # Br if no
+ jnz fam15_enable_stack_hook_exit\@ # Br if no
bt $FLAG_STACK_REENTRY , %esi # Check if stack has already been set
jc fam15_skipClearingBit4
@@ -1023,7 +1011,7 @@ fam15_skipClearingBit4:
btr $(COMBINE_CR0_CD - 32), %edx # Clear CombineCr0Cd bit
_WRMSR
-fam15_enable_stack_hook_exit:
+fam15_enable_stack_hook_exit\@:
.endm
/*****************************************************************************
@@ -1047,14 +1035,12 @@ fam15_enable_stack_hook_exit:
* * MSRC001_1022[DIS_HW_PF]=0
*****************************************************************************/
.macro AMD_DISABLE_STACK_FAMILY_HOOK_F15
- LOCAL fam15_disable_stack_hook_exit
- LOCAL fam15_disable_stack_remote_read_exit
AMD_CPUID $CPUID_MODEL
mov %eax, %ebx # Save revision info to EBX
shr $20, %eax # AL = cpu extended family
cmp $0x06, %al # Is this family 15h?
- jnz fam15_disable_stack_hook_exit # Br if no
+ jnz fam15_disable_stack_hook_exit\@ # Br if no
mov %ebx, %edi # Save revision info to EDI
AMD_CPUID $AMD_CPUID_APIC
@@ -1170,7 +1156,7 @@ fam15_enable_stack_hook_exit:
cmp $REMOTE_DELIVERY_PEND, %eax
jnz 8f
dec %ch # Check the timeout
- jz fam15_disable_stack_hook_exit # Branch if there is an unreponsive core
+ jz fam15_disable_stack_hook_exit\@ # Branch if there is an unreponsive core
stc
jmp 9f
8: #.else
@@ -1300,7 +1286,7 @@ fam15_disable_stack_remote_read_exit:
1: #.endif
-fam15_disable_stack_hook_exit:
+fam15_disable_stack_hook_exit\@:
.endm
/*****************************************************************************
@@ -1317,10 +1303,6 @@ fam15_disable_stack_hook_exit:
*****************************************************************************/
.macro GET_NODE_ID_CORE_ID_F15
- LOCAL node_core_f15_exit
- LOCAL node_core_f15_AP
- LOCAL node_core_f15_shared
- LOCAL node_core_f15_AP_not_TN
#define F15_L2Size 512
#define F15_ShareCores 2
@@ -1329,12 +1311,12 @@ fam15_disable_stack_hook_exit:
#define F15_SzAddrBus 48
#define F15_pad 0
cmp $-1, %si # Has node/core already been discovered?
- jnz node_core_f15_exit # Br if yes
+ jnz node_core_f15_exit\@ # Br if yes
AMD_CPUID $CPUID_MODEL
shr $12, %eax # AL = cpu extended family
cmp $06, %ah # Is this family 15h?
- jnz node_core_f15_exit # Br if no
+ jnz node_core_f15_exit\@ # Br if no
shr $4, %al # AL = cpu extended model
shr $16, %ebx # BH = LocalApicId
mov %al, %bl # BL = cpu extended model
@@ -1346,7 +1328,7 @@ fam15_disable_stack_hook_exit:
mov $APIC_BASE_ADDRESS, %ecx # MSR:0000_001B
_RDMSR
bt $APIC_BSC, %eax # Is this the BSC?
- jnc node_core_f15_AP # Br if no
+ jnc node_core_f15_AP\@ # Br if no
# This is the BSP.
# Enable routing tables on BSP (just in case the HT init code has not yet enabled them)
@@ -1357,17 +1339,17 @@ fam15_disable_stack_hook_exit:
in %dx, %eax
btr $0, %eax # Set LinkInitializationControl[RouteTblDis] = 0
out %eax, %dx
- jmp node_core_f15_shared #
+ jmp node_core_f15_shared\@ #
-node_core_f15_AP:
+node_core_f15_AP\@:
mov %bl, %al # AL = cpu extended model
shr $8, %bx # BL = CPUID Fn0000_0001_EBX[LocalApicId]
cmp $1, %al # Is This TN?
jz 4f
cmp $3, %al
- jnz node_core_f15_AP_not_TN
+ jnz node_core_f15_AP_not_TN\@
4: mov %bx, %si
- jmp node_core_f15_shared
+ jmp node_core_f15_shared\@
#
# This is an AP. Routing tables have been enabled by the HT Init process.
# Also, the MailBox register was set by the BSP during early init
@@ -1378,7 +1360,7 @@ node_core_f15_AP:
# UINT32 ModuleType:2; // Single Module = 0, Multi-module = 1.
# UINT32 :20; // Reserved
#
-node_core_f15_AP_not_TN:
+node_core_f15_AP_not_TN\@:
mov $0x0C0000408, %ecx # Read the family 15h mailbox
_RDMSR # MC4_MISC1[63:32]
mov %dx, %si # SI = raw mailbox contents (will extract node# from this)
@@ -1426,7 +1408,7 @@ node_core_f15_AP_not_TN:
#
# determine if this core shares MTRRs
#
-node_core_f15_shared:
+node_core_f15_shared\@:
mov $0x8000C580, %eax # Compute Unit Status
mov %si, %bx
shl $3, %bh # Move node# to PCI Dev# field
@@ -1489,7 +1471,7 @@ node_core_f15_shared:
#.endif
2:
-node_core_f15_exit:
+node_core_f15_exit\@:
.endm
@@ -1561,10 +1543,6 @@ node_core_f15_exit:
.macro AMD_ENABLE_STACK
# These are local labels. Declared so linker doesn't cause 'redefined label' errors
- LOCAL SetupStack
- LOCAL Real16bMode
- LOCAL Protected32Mode
- LOCAL ClearTheStack
# Note that SS:ESP will be default stack. Note that this stack
# routine will not be used after memory has been initialized. Because
@@ -1578,14 +1556,14 @@ node_core_f15_exit:
# It is =0 after reset; CAR setup sets it to enable the MTRRs
mov %cr0, %eax
test $CR0_MASK, %eax # Is cache disabled? (CD & NW bits)
- jnz SetupStack # Jump if yes
+ jnz SetupStack\@ # Jump if yes
mov $AMD_MTRR_DEFTYPE, %ecx # MSR:0000_02FF
_RDMSR
test $MSR_MASK, %eax # Are the default types enabled? (MTRR_DEF_TYPE_EN + MTRR_DEF_TYPE_FIX_EN)
- jz SetupStack # Jump if no
+ jz SetupStack\@ # Jump if no
or $FLAG_STACK_REENTRY, %esi # Bit25, indicate stack has already been initialized
-SetupStack:
+SetupStack\@:
# Set node to map the first 16MB to node 0# 0000_0000 to 00FF_FFFF as DRAM
mov %esi, %ebx # Get my Node/Core info
xor %bl, %bl
@@ -1816,12 +1794,12 @@ SetupStack:
mov %cr0, %ecx # Check for 32-bit protect mode
bt $CR0_PE, %ecx #
#.if (!carry?) # PE=0 means real mode
- jc Protected32Mode
+ jc Protected32Mode\@
mov %cs, %cx # PE=1
cmp $0x0D000, %cx # Check for CS
- jb Protected32Mode # If CS < D000, it is a selector instead of a segment
+ jb Protected32Mode\@ # If CS < D000, it is a selector instead of a segment
# alter SS:ESP for 16b Real Mode:
-Real16bMode:
+Real16bMode\@:
mov %edi, %eax
shr $4, %eax # Create a Real Mode segment for ss, ds, es
mov %ax, %ss
@@ -1836,7 +1814,7 @@ Real16bMode:
# Default is to use Protected 32b Mode
#.endif
;
-Protected32Mode:
+Protected32Mode\@:
#
# Clear The Stack
# Now that we have set the location and the MTRRs, initialize the cache by
@@ -1849,7 +1827,7 @@ Protected32Mode:
# edi - address of start of stack block
#
-ClearTheStack: # Stack base is in SS, stack pointer is in ESP
+ClearTheStack\@: # Stack base is in SS, stack pointer is in ESP
shr $2, %ebx # ebx = stack block size in dwords
mov %bx, %cx #
# Check our flags - Don't clear an existing stack
diff --git a/src/vendorcode/amd/agesa/f16kb/gcccar.inc b/src/vendorcode/amd/agesa/f16kb/gcccar.inc
index 9c7bf47f43..cffebffbe1 100644
--- a/src/vendorcode/amd/agesa/f16kb/gcccar.inc
+++ b/src/vendorcode/amd/agesa/f16kb/gcccar.inc
@@ -281,7 +281,6 @@ MSR_MASK = ((1 << MTRR_DEF_TYPE_EN)+(1 << MTRR_DEF_TYPE_FIX_EN))
* SI[31:27]= reserved, =0
****************************************************************************/
.macro GET_NODE_ID_CORE_ID
- LOCAL node_core_exit
mov $-1, %si
GET_NODE_ID_CORE_ID_F16
@@ -290,16 +289,16 @@ MSR_MASK = ((1 << MTRR_DEF_TYPE_EN)+(1 << MTRR_DEF_TYPE_FIX_EN))
* Check for unrecognized Family
*/
cmp $-1, %si # Has family (node/core) already been discovered?
- jnz node_core_exit # Br if yes
+ jnz node_core_exit\@ # Br if yes
mov $((1 << FLAG_UNKNOWN_FAMILY)+(1 << FLAG_IS_PRIMARY)), %esi # No, Set error code, Only let BSP continue
mov $APIC_BASE_ADDRESS, %ecx # MSR:0000_001B
_RDMSR
bt $APIC_BSC, %eax # Is this the BSC?
- jc node_core_exit # Br if yes
+ jc node_core_exit\@ # Br if yes
hlt # Kill APs
-node_core_exit:
+node_core_exit\@:
.endm
@@ -335,13 +334,12 @@ Family 16h requirements (BKDG #48751 section 2.3.3):
*/
.macro AMD_ENABLE_STACK_FAMILY_HOOK_F16
- LOCAL fam16_enable_stack_hook_exit
AMD_CPUID $CPUID_MODEL
mov %eax, %ebx # Save revision info to EBX
shr $20, %eax # AL = cpu extended family
cmp $0x07, %al # Is this family 16h?
- jnz fam16_enable_stack_hook_exit # Br if no
+ jnz fam16_enable_stack_hook_exit\@ # Br if no
bt $FLAG_STACK_REENTRY , %esi # Check if stack has already been set
jc fam16_skipClearingBit4
@@ -373,7 +371,7 @@ fam16_skipClearingBit4:
bts $CACHE_IC_ATTR_DIS, %eax
_WRMSR
-fam16_enable_stack_hook_exit:
+fam16_enable_stack_hook_exit\@:
.endm
/*
@@ -400,15 +398,12 @@ fam16_enable_stack_hook_exit:
;---------------------------------------------------
*/
.macro AMD_DISABLE_STACK_FAMILY_HOOK_F16
- LOCAL fam16_disable_stack_hook_exit
- LOCAL fam16_disable_stack_remote_read_exit
-# LOCAL fam16_invd_done_remote_read_exit
AMD_CPUID $CPUID_MODEL
mov %eax, %ebx # Save revision info to EBX
shr $20, %eax # AL = cpu extended family
cmp $0x07, %al # Is this family 16h?
- jnz fam16_disable_stack_hook_exit # Br if no
+ jnz fam16_disable_stack_hook_exit\@ # Br if no
mov %ebx, %edi # Save revision info to EDI
AMD_CPUID $AMD_CPUID_APIC
@@ -510,7 +505,7 @@ fam16_enable_stack_hook_exit:
#.while (carry?)
7: jnc 6f
dec %ch #Check the timeout
- jz fam16_disable_stack_remote_read_exit
+ jz fam16_disable_stack_remote_read_exit\@
mov %es:(%ebx), %eax # ax = 0000000000020338
bt $DELIVERY_STS_BIT, %eax
jmp 7b
@@ -524,7 +519,7 @@ fam16_enable_stack_hook_exit:
cmp $REMOTE_DELIVERY_PEND, %eax
jnz 8f
dec %ch # Check the timeout
- jz fam16_disable_stack_hook_exit # Branch if there is an unreponsive core
+ jz fam16_disable_stack_hook_exit\@ # Branch if there is an unreponsive core
stc
jmp 9f
8: #.else
@@ -549,13 +544,13 @@ fam16_enable_stack_hook_exit:
jmp 7f
6: #.else
dec %ch
- jz fam16_disable_stack_remote_read_exit
+ jz fam16_disable_stack_remote_read_exit\@
stc
7: #.endif
jmp 5b
4: #.endw
-fam16_disable_stack_remote_read_exit:
+fam16_disable_stack_remote_read_exit\@:
rol $8, %ecx # Restore ECX
1: #.endif
@@ -658,7 +653,7 @@ fam16_disable_stack_remote_read_exit:
#.while (carry?)
7: jnc 6f
dec %ch #Check the timeout
- jz fam16_invd_done_remote_read_exit
+ jz fam16_invd_done_remote_read_exit\@
mov %es:(%ebx), %eax # ax = 0000000000020338
bt $DELIVERY_STS_BIT, %eax
jmp 7b
@@ -672,7 +667,7 @@ fam16_disable_stack_remote_read_exit:
cmp $REMOTE_DELIVERY_PEND, %eax
jnz 8f
dec %ch # Check the timeout
- jz fam16_invd_done_remote_read_exit # Branch if there is an unreponsive core
+ jz fam16_invd_done_remote_read_exit\@ # Branch if there is an unreponsive core
stc
jmp 9f
8: #.else
@@ -697,14 +692,14 @@ fam16_disable_stack_remote_read_exit:
jmp 7f
6: #.else
dec %ch
- jz fam16_invd_done_remote_read_exit
+ jz fam16_invd_done_remote_read_exit\@
stc
7: #.endif
jmp 5b
4: #.endw
jmp 2f
-fam16_invd_done_remote_read_exit:
+fam16_invd_done_remote_read_exit\@:
1: #.else
mov $APIC_BASE_ADDRESS, %ecx
_RDMSR
@@ -715,17 +710,13 @@ fam16_invd_done_remote_read_exit:
mov %edi, %es:(%ebx)
2: #.endif
-fam16_disable_stack_hook_exit:
+fam16_disable_stack_hook_exit\@:
.endm
/*
*/
.macro GET_NODE_ID_CORE_ID_F16
- LOCAL node_core_f16_exit
- LOCAL node_core_f16_AP
- LOCAL node_core_f16_shared
- LOCAL node_core_f16_AP_not_TN
#define F16_L2Size 1024
#define F16_ShareCores 4
@@ -734,12 +725,12 @@ fam16_disable_stack_hook_exit:
#define F16_SzAddrBus 40
#define F16_pad 0
cmp $-1, %si # Has node/core already been discovered?
- jnz node_core_f16_exit # Br if yes
+ jnz node_core_f16_exit\@ # Br if yes
AMD_CPUID $CPUID_MODEL
shr $12, %eax # AL = cpu extended family
cmp $07, %ah # Is this family 16h?
- jnz node_core_f16_exit # Br if no
+ jnz node_core_f16_exit\@ # Br if no
shr $4, %al # AL = cpu extended model
shr $16, %ebx # BH = LocalApicId
mov %al, %bl # BL = cpu extended model
@@ -751,7 +742,7 @@ fam16_disable_stack_hook_exit:
mov $APIC_BASE_ADDRESS, %ecx # MSR:0000_001B
_RDMSR
bt $APIC_BSC, %eax # Is this the BSC?
- jnc node_core_f16_AP # Br if no
+ jnc node_core_f16_AP\@ # Br if no
# This is the BSP.
# Enable routing tables on BSP (just in case the HT init code has not yet enabled them)
@@ -764,7 +755,7 @@ fam16_disable_stack_hook_exit:
out %eax, %dx
jmp 6f #node_core_f16_shared #
-node_core_f16_AP:
+node_core_f16_AP\@:
mov %bl, %al # AL = cpu extended model
shr $8, %bx # BL = CPUID Fn0000_0001_EBX[LocalApicId]
#.if (al == 0)
@@ -853,7 +844,7 @@ node_core_f16_AP:
#.endif
2:
-node_core_f16_exit:
+node_core_f16_exit\@:
.endm
@@ -925,10 +916,6 @@ node_core_f16_exit:
.macro AMD_ENABLE_STACK
# These are local labels. Declared so linker doesn't cause 'redefined label' errors
- LOCAL SetupStack
- LOCAL Real16bMode
- LOCAL Protected32Mode
- LOCAL ClearTheStack
# Note that SS:ESP will be default stack. Note that this stack
# routine will not be used after memory has been initialized. Because
@@ -942,14 +929,14 @@ node_core_f16_exit:
# It is =0 after reset; CAR setup sets it to enable the MTRRs
mov %cr0, %eax
test $CR0_MASK, %eax # Is cache disabled? (CD & NW bits)
- jnz SetupStack # Jump if yes
+ jnz SetupStack\@ # Jump if yes
mov $AMD_MTRR_DEFTYPE, %ecx # MSR:0000_02FF
_RDMSR
test $MSR_MASK, %eax # Are the default types enabled? (MTRR_DEF_TYPE_EN + MTRR_DEF_TYPE_FIX_EN)
- jz SetupStack # Jump if no
+ jz SetupStack\@ # Jump if no
or $FLAG_STACK_REENTRY, %esi # Bit25, indicate stack has already been initialized
-SetupStack:
+SetupStack\@:
# Set node to map the first 16MB to node 0# 0000_0000 to 00FF_FFFF as DRAM
mov %esi, %ebx # Get my Node/Core info
xor %bl, %bl
@@ -1180,12 +1167,12 @@ SetupStack:
mov %cr0, %ecx # Check for 32-bit protect mode
bt $CR0_PE, %ecx #
#.if (!carry?) # PE=0 means real mode
- jc Protected32Mode
+ jc Protected32Mode\@
mov %cs, %cx # PE=1
cmp $0x0D000, %cx # Check for CS
- jb Protected32Mode # If CS < D000, it is a selector instead of a segment
+ jb Protected32Mode\@ # If CS < D000, it is a selector instead of a segment
# alter SS:ESP for 16b Real Mode:
-Real16bMode:
+Real16bMode\@:
mov %edi, %eax
shr $4, %eax # Create a Real Mode segment for ss, ds, es
mov %ax, %ss
@@ -1200,7 +1187,7 @@ Real16bMode:
# Default is to use Protected 32b Mode
#.endif
;
-Protected32Mode:
+Protected32Mode\@:
#
# Clear The Stack
# Now that we have set the location and the MTRRs, initialize the cache by
@@ -1213,7 +1200,7 @@ Protected32Mode:
# edi - address of start of stack block
#
-ClearTheStack: # Stack base is in SS, stack pointer is in ESP
+ClearTheStack\@: # Stack base is in SS, stack pointer is in ESP
shr $2, %ebx # ebx = stack block size in dwords
mov %bx, %cx #
# Check our flags - Don't clear an existing stack
diff --git a/src/vendorcode/amd/pi/00670F00/binaryPI/gcccar.inc b/src/vendorcode/amd/pi/00670F00/binaryPI/gcccar.inc
index 152e2799c6..ae0ad37d17 100644
--- a/src/vendorcode/amd/pi/00670F00/binaryPI/gcccar.inc
+++ b/src/vendorcode/amd/pi/00670F00/binaryPI/gcccar.inc
@@ -290,7 +290,6 @@ MSR_MASK = ((1 << MTRR_DEF_TYPE_EN)+(1 << MTRR_DEF_TYPE_FIX_EN))
* SI[31:27]= reserved, =0
****************************************************************************/
.macro GET_NODE_ID_CORE_ID
- LOCAL node_core_exit
mov $-1, %si
//GET_NODE_ID_CORE_ID_F10
@@ -301,16 +300,16 @@ MSR_MASK = ((1 << MTRR_DEF_TYPE_EN)+(1 << MTRR_DEF_TYPE_FIX_EN))
* Check for unrecognized Family
*/
cmp $-1, %si # Has family (node/core) already been discovered?
- jnz node_core_exit # Br if yes
+ jnz node_core_exit\@ # Br if yes
mov $((1 << FLAG_UNKNOWN_FAMILY)+(1 << FLAG_IS_PRIMARY)), %esi # No, Set error code, Only let BSP continue
mov $APIC_BASE_ADDRESS, %ecx # MSR:0000_001B
_RDMSR
bt $APIC_BSC, %eax # Is this the BSC?
- jc node_core_exit # Br if yes
+ jc node_core_exit\@ # Br if yes
hlt # Kill APs
-node_core_exit:
+node_core_exit\@:
.endm
@@ -340,13 +339,12 @@ node_core_exit:
* * No INVD or WBINVD, no exceptions, page faults or interrupts
*****************************************************************************/
.macro AMD_ENABLE_STACK_FAMILY_HOOK_F15
- LOCAL fam15_enable_stack_hook_exit
AMD_CPUID $CPUID_MODEL
mov %eax, %ebx # Save revision info to EBX
shr $20, %eax # AL = cpu extended family
cmp $0x06, %al # Is this family 15h?
- jnz fam15_enable_stack_hook_exit # Br if no
+ jnz fam15_enable_stack_hook_exit\@ # Br if no
bt $FLAG_STACK_REENTRY , %esi # Check if stack has already been set
jc fam15_skipClearingBit4
@@ -391,7 +389,7 @@ dofamily15w: # Do Standard Family 15 work
btr $(COMBINE_CR0_CD - 32), %edx # Clear CombineCr0Cd bit
_WRMSR
-fam15_enable_stack_hook_exit:
+fam15_enable_stack_hook_exit\@:
.endm
/*****************************************************************************
@@ -415,14 +413,12 @@ fam15_enable_stack_hook_exit:
* * MSRC001_1022[DIS_HW_PF]=0
*****************************************************************************/
.macro AMD_DISABLE_STACK_FAMILY_HOOK_F15
- LOCAL fam15_disable_stack_hook_exit
- LOCAL fam15_disable_stack_remote_read_exit
AMD_CPUID $CPUID_MODEL
mov %eax, %ebx # Save revision info to EBX
shr $20, %eax # AL = cpu extended family
cmp $0x06, %al # Is this family 15h?
- jnz fam15_disable_stack_hook_exit # Br if no
+ jnz fam15_disable_stack_hook_exit\@ # Br if no
mov %ebx, %edi # Save revision info to EDI
AMD_CPUID $AMD_CPUID_APIC
@@ -525,7 +521,7 @@ fam15_enable_stack_hook_exit:
#.while (carry?)
7: jnc 6f
dec %ch #Check the timeout
- jz fam15_disable_stack_remote_read_exit
+ jz fam15_disable_stack_remote_read_exit\@
mov %es:(%ebx), %eax # ax = 0000000000020338
bt $DELIVERY_STS_BIT, %eax
jmp 7b
@@ -539,7 +535,7 @@ fam15_enable_stack_hook_exit:
cmp $REMOTE_DELIVERY_PEND, %eax
jnz 8f
dec %ch # Check the timeout
- jz fam15_disable_stack_hook_exit # Branch if there is an unreponsive core
+ jz fam15_disable_stack_hook_exit\@ # Branch if there is an unreponsive core
stc
jmp 9f
8: #.else
@@ -564,13 +560,13 @@ fam15_enable_stack_hook_exit:
jmp 7f
6: #.else
dec %ch
- jz fam15_disable_stack_remote_read_exit
+ jz fam15_disable_stack_remote_read_exit\@
stc
7: #.endif
jmp 5b
4: #.endw
-fam15_disable_stack_remote_read_exit:
+fam15_disable_stack_remote_read_exit\@:
rol $8, %ecx # Restore ECX
1: #.endif
@@ -686,7 +682,7 @@ fam15_disable_stack_remote_read_exit:
1: #.endif
-fam15_disable_stack_hook_exit:
+fam15_disable_stack_hook_exit\@:
.endm
/*****************************************************************************
@@ -703,9 +699,6 @@ fam15_disable_stack_hook_exit:
*****************************************************************************/
.macro GET_NODE_ID_CORE_ID_F15
- LOCAL node_core_f15_exit
- LOCAL node_core_f15_AP
- LOCAL node_core_f15_shared
#define F15_L2Size 512
#define F15_ShareCores 2
@@ -714,12 +707,12 @@ fam15_disable_stack_hook_exit:
#define F15_SzAddrBus 48
#define F15_pad 0
cmp $-1, %si # Has node/core already been discovered?
- jnz node_core_f15_exit # Br if yes
+ jnz node_core_f15_exit\@ # Br if yes
AMD_CPUID $CPUID_MODEL
shr $12, %eax # AL = cpu extended family
cmp $06, %ah # Is this family 15h?
- jnz node_core_f15_exit # Br if no
+ jnz node_core_f15_exit\@ # Br if no
shr $4, %al # AL = cpu extended model
shr $16, %ebx # BH = LocalApicId
mov %al, %bl # BL = cpu extended model
@@ -731,7 +724,7 @@ fam15_disable_stack_hook_exit:
mov $APIC_BASE_ADDRESS, %ecx # MSR:0000_001B
_RDMSR
bt $APIC_BSC, %eax # Is this the BSC?
- jnc node_core_f15_AP # Br if no
+ jnc node_core_f15_AP\@ # Br if no
# This is the BSP.
# Enable routing tables on BSP (just in case the HT init code has not yet enabled them)
@@ -742,18 +735,18 @@ fam15_disable_stack_hook_exit:
in %dx, %eax
btr $0, %eax # Set LinkInitializationControl[RouteTblDis] = 0
out %eax, %dx
- jmp node_core_f15_shared #
+ jmp node_core_f15_shared\@ #
-node_core_f15_AP:
+node_core_f15_AP\@:
//1: jmp 1b # not crash
mov %bl, %al # AL = cpu extended model
shr $8, %bx # BL = CPUID Fn0000_0001_EBX[LocalApicId]
// cmp $1, %al # Is This TN?
// jz 4f
// cmp $3, %al
-// jnz node_core_f15_AP_not_TN
+// jnz node_core_f15_AP_not_TN\@
mov %bx, %si
- jmp node_core_f15_shared
+ jmp node_core_f15_shared\@
#
# This is an AP. Routing tables have been enabled by the HT Init process.
# Also, the MailBox register was set by the BSP during early init
@@ -764,7 +757,7 @@ node_core_f15_AP:
# UINT32 ModuleType:2; // Single Module = 0, Multi-module = 1.
# UINT32 :20; // Reserved
#
-#node_core_f15_AP_not_TN:
+#node_core_f15_AP_not_TN\@:
# mov $0x0C0000408, %ecx # Read the family 15h mailbox
# _RDMSR # MC4_MISC1[63:32]
# mov %dx, %si # SI = raw mailbox contents (will extract node# from this)
@@ -812,7 +805,7 @@ node_core_f15_AP:
#
# determine if this core shares MTRRs
#
-node_core_f15_shared:
+node_core_f15_shared\@:
mov $0x8000C580, %eax # Compute Unit Status
mov %si, %bx
shl $3, %bh # Move node# to PCI Dev# field
@@ -875,7 +868,7 @@ node_core_f15_shared:
#.endif
2:
-node_core_f15_exit:
+node_core_f15_exit\@:
.endm
@@ -947,10 +940,6 @@ node_core_f15_exit:
.macro AMD_ENABLE_STACK
# These are local labels. Declared so linker doesn't cause 'redefined label' errors
- LOCAL SetupStack
- LOCAL Real16bMode
- LOCAL Protected32Mode
- LOCAL ClearTheStack
# Note that SS:ESP will be default stack. Note that this stack
# routine will not be used after memory has been initialized. Because
@@ -964,14 +953,14 @@ node_core_f15_exit:
# It is =0 after reset; CAR setup sets it to enable the MTRRs
mov %cr0, %eax
test $CR0_MASK, %eax # Is cache disabled? (CD & NW bits)
- jnz SetupStack # Jump if yes
+ jnz SetupStack\@ # Jump if yes
mov $AMD_MTRR_DEFTYPE, %ecx # MSR:0000_02FF
_RDMSR
test $MSR_MASK, %eax # Are the default types enabled? (MTRR_DEF_TYPE_EN + MTRR_DEF_TYPE_FIX_EN)
- jz SetupStack # Jump if no
+ jz SetupStack\@ # Jump if no
or $FLAG_STACK_REENTRY, %esi # Bit25, indicate stack has already been initialized
-SetupStack:
+SetupStack\@:
# Set node to map the first 16MB to node 0# 0000_0000 to 00FF_FFFF as DRAM
mov %esi, %ebx # Get my Node/Core info
xor %bl, %bl
@@ -1214,12 +1203,12 @@ w64k_here:
mov %cr0, %ecx # Check for 32-bit protect mode
bt $CR0_PE, %ecx #
#.if (!carry?) # PE=0 means real mode
- jc Protected32Mode
+ jc Protected32Mode\@
mov %cs, %cx # PE=1
cmp $0x0D000, %cx # Check for CS
- jb Protected32Mode # If CS < D000, it is a selector instead of a segment
+ jb Protected32Mode\@ # If CS < D000, it is a selector instead of a segment
# alter SS:ESP for 16b Real Mode:
-Real16bMode:
+Real16bMode\@:
mov %edi, %eax
shr $4, %eax # Create a Real Mode segment for ss, ds, es
mov %ax, %ss
@@ -1234,7 +1223,7 @@ Real16bMode:
# Default is to use Protected 32b Mode
#.endif
;
-Protected32Mode:
+Protected32Mode\@:
#
# Clear The Stack
# Now that we have set the location and the MTRRs, initialize the cache by
@@ -1247,7 +1236,7 @@ Protected32Mode:
# edi - address of start of stack block
#
-ClearTheStack: # Stack base is in SS, stack pointer is in ESP
+ClearTheStack\@: # Stack base is in SS, stack pointer is in ESP
shr $2, %ebx # ebx = stack block size in dwords
mov %bx, %cx #
# Check our flags - Don't clear an existing stack
@@ -1322,4 +1311,3 @@ ClearTheStack: # Stack base is in SS, stack pointer is
AMD_DISABLE_STACK_FAMILY_HOOK # Re-Enable 'normal' cache operations
.endm
-
diff --git a/src/vendorcode/amd/pi/00730F01/binaryPI/gcccar.inc b/src/vendorcode/amd/pi/00730F01/binaryPI/gcccar.inc
index ef08c87761..3218a64265 100644
--- a/src/vendorcode/amd/pi/00730F01/binaryPI/gcccar.inc
+++ b/src/vendorcode/amd/pi/00730F01/binaryPI/gcccar.inc
@@ -281,7 +281,6 @@ MSR_MASK = ((1 << MTRR_DEF_TYPE_EN)+(1 << MTRR_DEF_TYPE_FIX_EN))
* SI[31:27]= reserved, =0
****************************************************************************/
.macro GET_NODE_ID_CORE_ID
- LOCAL node_core_exit
mov $-1, %si
GET_NODE_ID_CORE_ID_F16
@@ -290,16 +289,16 @@ MSR_MASK = ((1 << MTRR_DEF_TYPE_EN)+(1 << MTRR_DEF_TYPE_FIX_EN))
* Check for unrecognized Family
*/
cmp $-1, %si # Has family (node/core) already been discovered?
- jnz node_core_exit # Br if yes
+ jnz node_core_exit\@ # Br if yes
mov $((1 << FLAG_UNKNOWN_FAMILY)+(1 << FLAG_IS_PRIMARY)), %esi # No, Set error code, Only let BSP continue
mov $APIC_BASE_ADDRESS, %ecx # MSR:0000_001B
_RDMSR
bt $APIC_BSC, %eax # Is this the BSC?
- jc node_core_exit # Br if yes
+ jc node_core_exit\@ # Br if yes
hlt # Kill APs
-node_core_exit:
+node_core_exit\@:
.endm
@@ -335,13 +334,12 @@ Family 16h requirements (BKDG #48751 section 2.3.3):
*/
.macro AMD_ENABLE_STACK_FAMILY_HOOK_F16
- LOCAL fam16_enable_stack_hook_exit
AMD_CPUID $CPUID_MODEL
mov %eax, %ebx # Save revision info to EBX
shr $20, %eax # AL = cpu extended family
cmp $0x07, %al # Is this family 16h?
- jnz fam16_enable_stack_hook_exit # Br if no
+ jnz fam16_enable_stack_hook_exit\@ # Br if no
bt $FLAG_STACK_REENTRY , %esi # Check if stack has already been set
jc fam16_skipClearingBit4
@@ -373,7 +371,7 @@ fam16_skipClearingBit4:
bts $CACHE_IC_ATTR_DIS, %eax
_WRMSR
-fam16_enable_stack_hook_exit:
+fam16_enable_stack_hook_exit\@:
.endm
/*
@@ -400,15 +398,12 @@ fam16_enable_stack_hook_exit:
;---------------------------------------------------
*/
.macro AMD_DISABLE_STACK_FAMILY_HOOK_F16
- LOCAL fam16_disable_stack_hook_exit
- LOCAL fam16_disable_stack_remote_read_exit
-# LOCAL fam16_invd_done_remote_read_exit
AMD_CPUID $CPUID_MODEL
mov %eax, %ebx # Save revision info to EBX
shr $20, %eax # AL = cpu extended family
cmp $0x07, %al # Is this family 16h?
- jnz fam16_disable_stack_hook_exit # Br if no
+ jnz fam16_disable_stack_hook_exit\@ # Br if no
mov %ebx, %edi # Save revision info to EDI
AMD_CPUID $AMD_CPUID_APIC
@@ -510,7 +505,7 @@ fam16_enable_stack_hook_exit:
#.while (carry?)
7: jnc 6f
dec %ch #Check the timeout
- jz fam16_disable_stack_remote_read_exit
+ jz fam16_disable_stack_remote_read_exit\@
mov %es:(%ebx), %eax # ax = 0000000000020338
bt $DELIVERY_STS_BIT, %eax
jmp 7b
@@ -524,7 +519,7 @@ fam16_enable_stack_hook_exit:
cmp $REMOTE_DELIVERY_PEND, %eax
jnz 8f
dec %ch # Check the timeout
- jz fam16_disable_stack_hook_exit # Branch if there is an unreponsive core
+ jz fam16_disable_stack_hook_exit\@ # Branch if there is an unreponsive core
stc
jmp 9f
8: #.else
@@ -549,13 +544,13 @@ fam16_enable_stack_hook_exit:
jmp 7f
6: #.else
dec %ch
- jz fam16_disable_stack_remote_read_exit
+ jz fam16_disable_stack_remote_read_exit\@
stc
7: #.endif
jmp 5b
4: #.endw
-fam16_disable_stack_remote_read_exit:
+fam16_disable_stack_remote_read_exit\@:
rol $8, %ecx # Restore ECX
1: #.endif
@@ -660,7 +655,7 @@ fam16_disable_stack_remote_read_exit:
#.while (carry?)
7: jnc 6f
dec %ch #Check the timeout
- jz fam16_invd_done_remote_read_exit
+ jz fam16_invd_done_remote_read_exit\@
mov %es:(%ebx), %eax # ax = 0000000000020338
bt $DELIVERY_STS_BIT, %eax
jmp 7b
@@ -674,7 +669,7 @@ fam16_disable_stack_remote_read_exit:
cmp $REMOTE_DELIVERY_PEND, %eax
jnz 8f
dec %ch # Check the timeout
- jz fam16_invd_done_remote_read_exit # Branch if there is an unreponsive core
+ jz fam16_invd_done_remote_read_exit\@ # Branch if there is an unreponsive core
stc
jmp 9f
8: #.else
@@ -699,14 +694,14 @@ fam16_disable_stack_remote_read_exit:
jmp 7f
6: #.else
dec %ch
- jz fam16_invd_done_remote_read_exit
+ jz fam16_invd_done_remote_read_exit\@
stc
7: #.endif
jmp 5b
4: #.endw
jmp 2f
-fam16_invd_done_remote_read_exit:
+fam16_invd_done_remote_read_exit\@:
1: #.else
mov $APIC_BASE_ADDRESS, %ecx
_RDMSR
@@ -722,17 +717,13 @@ fam16_invd_done_remote_read_exit:
btr $30, %edx
_WRMSR
-fam16_disable_stack_hook_exit:
+fam16_disable_stack_hook_exit\@:
.endm
/*
*/
.macro GET_NODE_ID_CORE_ID_F16
- LOCAL node_core_f16_exit
- LOCAL node_core_f16_AP
- LOCAL node_core_f16_shared
- LOCAL node_core_f16_AP_not_TN
#define F16_L2Size 1024
#define F16_ShareCores 4
@@ -741,12 +732,12 @@ fam16_disable_stack_hook_exit:
#define F16_SzAddrBus 40
#define F16_pad 0
cmp $-1, %si # Has node/core already been discovered?
- jnz node_core_f16_exit # Br if yes
+ jnz node_core_f16_exit\@ # Br if yes
AMD_CPUID $CPUID_MODEL
shr $12, %eax # AL = cpu extended family
cmp $07, %ah # Is this family 16h?
- jnz node_core_f16_exit # Br if no
+ jnz node_core_f16_exit\@ # Br if no
shr $4, %al # AL = cpu extended model
shr $16, %ebx # BH = LocalApicId
mov %al, %bl # BL = cpu extended model
@@ -758,7 +749,7 @@ fam16_disable_stack_hook_exit:
mov $APIC_BASE_ADDRESS, %ecx # MSR:0000_001B
_RDMSR
bt $APIC_BSC, %eax # Is this the BSC?
- jnc node_core_f16_AP # Br if no
+ jnc node_core_f16_AP\@ # Br if no
# This is the BSP.
# Enable routing tables on BSP (just in case the HT init code has not yet enabled them)
@@ -769,9 +760,9 @@ fam16_disable_stack_hook_exit:
in %dx, %eax
btr $0, %eax # Set LinkInitializationControl[RouteTblDis] = 0
out %eax, %dx
- jmp 6f #node_core_f16_shared #
+ jmp 6f #node_core_f16_shared\@ #
-node_core_f16_AP:
+node_core_f16_AP\@:
mov %bl, %al # AL = cpu extended model
shr $8, %bx # BL = CPUID Fn0000_0001_EBX[LocalApicId]
#.if (al == 0)
@@ -780,14 +771,14 @@ node_core_f16_AP:
#.else
4: mov %bx, %si
jmp 6f
-5: #node_core_f16_AP_not_KB
+5: #node_core_f16_AP_not_KB\@
bts $FLAG_CORE_NOT_IDENTIFIED, %esi
#.endif
#.endif
#
# determine if this core shares MTRRs
#
-6: #node_core_f16_shared
+6: #node_core_f16_shared\@
mov $COMPUTE_UNIT_STATUS, %eax # Compute Unit Status
mov %si, %bx
shl $3, %bh # Move node# to PCI Dev# field
@@ -860,7 +851,7 @@ node_core_f16_AP:
#.endif
2:
-node_core_f16_exit:
+node_core_f16_exit\@:
.endm
@@ -932,10 +923,6 @@ node_core_f16_exit:
.macro AMD_ENABLE_STACK
# These are local labels. Declared so linker doesn't cause 'redefined label' errors
- LOCAL SetupStack
- LOCAL Real16bMode
- LOCAL Protected32Mode
- LOCAL ClearTheStack
# Note that SS:ESP will be default stack. Note that this stack
# routine will not be used after memory has been initialized. Because
@@ -949,14 +936,14 @@ node_core_f16_exit:
# It is =0 after reset; CAR setup sets it to enable the MTRRs
mov %cr0, %eax
test $CR0_MASK, %eax # Is cache disabled? (CD & NW bits)
- jnz SetupStack # Jump if yes
+ jnz SetupStack\@ # Jump if yes
mov $AMD_MTRR_DEFTYPE, %ecx # MSR:0000_02FF
_RDMSR
test $MSR_MASK, %eax # Are the default types enabled? (MTRR_DEF_TYPE_EN + MTRR_DEF_TYPE_FIX_EN)
- jz SetupStack # Jump if no
+ jz SetupStack\@ # Jump if no
or $FLAG_STACK_REENTRY, %esi # Bit25, indicate stack has already been initialized
-SetupStack:
+SetupStack\@:
# Set node to map the first 16MB to node 0# 0000_0000 to 00FF_FFFF as DRAM
mov %esi, %ebx # Get my Node/Core info
xor %bl, %bl
@@ -1194,12 +1181,12 @@ SetupStack:
mov %cr0, %ecx # Check for 32-bit protect mode
bt $CR0_PE, %ecx #
#.if (!carry?) # PE=0 means real mode
- jc Protected32Mode
+ jc Protected32Mode\@
mov %cs, %cx # PE=1
cmp $0x0D000, %cx # Check for CS
- jb Protected32Mode # If CS < D000, it is a selector instead of a segment
+ jb Protected32Mode\@ # If CS < D000, it is a selector instead of a segment
# alter SS:ESP for 16b Real Mode:
-Real16bMode:
+Real16bMode\@:
mov %edi, %eax
shr $4, %eax # Create a Real Mode segment for ss, ds, es
mov %ax, %ss
@@ -1214,7 +1201,7 @@ Real16bMode:
# Default is to use Protected 32b Mode
#.endif
;
-Protected32Mode:
+Protected32Mode\@:
#
# Clear The Stack
# Now that we have set the location and the MTRRs, initialize the cache by
@@ -1227,7 +1214,7 @@ Protected32Mode:
# edi - address of start of stack block
#
-ClearTheStack: # Stack base is in SS, stack pointer is in ESP
+ClearTheStack\@: # Stack base is in SS, stack pointer is in ESP
shr $2, %ebx # ebx = stack block size in dwords
mov %bx, %cx #
# Check our flags - Don't clear an existing stack
@@ -1303,4 +1290,3 @@ ClearTheStack: # Stack base is in SS, stack pointer is
AMD_DISABLE_STACK_FAMILY_HOOK # Re-Enable 'normal' cache operations
.endm
-
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-10 07:42:37 +0000