diff options
Diffstat (limited to 'src/vendorcode/cavium/include/bdk/libbdk-hal/bdk-mpi.h')
-rw-r--r-- | src/vendorcode/cavium/include/bdk/libbdk-hal/bdk-mpi.h | 105 |
1 files changed, 105 insertions, 0 deletions
diff --git a/src/vendorcode/cavium/include/bdk/libbdk-hal/bdk-mpi.h b/src/vendorcode/cavium/include/bdk/libbdk-hal/bdk-mpi.h new file mode 100644 index 0000000000..46da75b019 --- /dev/null +++ b/src/vendorcode/cavium/include/bdk/libbdk-hal/bdk-mpi.h @@ -0,0 +1,105 @@ +/***********************license start*********************************** +* Copyright (c) 2003-2017 Cavium Inc. (support@cavium.com). All rights +* reserved. +* +* +* Redistribution and use in source and binary forms, with or without +* modification, are permitted provided that the following conditions are +* met: +* +* * Redistributions of source code must retain the above copyright +* notice, this list of conditions and the following disclaimer. +* +* * Redistributions in binary form must reproduce the above +* copyright notice, this list of conditions and the following +* disclaimer in the documentation and/or other materials provided +* with the distribution. +* +* * Neither the name of Cavium Inc. nor the names of +* its contributors may be used to endorse or promote products +* derived from this software without specific prior written +* permission. +* +* This Software, including technical data, may be subject to U.S. export +* control laws, including the U.S. Export Administration Act and its +* associated regulations, and may be subject to export or import +* regulations in other countries. +* +* TO THE MAXIMUM EXTENT PERMITTED BY LAW, THE SOFTWARE IS PROVIDED "AS IS" +* AND WITH ALL FAULTS AND CAVIUM INC. MAKES NO PROMISES, REPRESENTATIONS OR +* WARRANTIES, EITHER EXPRESS, IMPLIED, STATUTORY, OR OTHERWISE, WITH RESPECT +* TO THE SOFTWARE, INCLUDING ITS CONDITION, ITS CONFORMITY TO ANY +* REPRESENTATION OR DESCRIPTION, OR THE EXISTENCE OF ANY LATENT OR PATENT +* DEFECTS, AND CAVIUM SPECIFICALLY DISCLAIMS ALL IMPLIED (IF ANY) WARRANTIES +* OF TITLE, MERCHANTABILITY, NONINFRINGEMENT, FITNESS FOR A PARTICULAR +* PURPOSE, LACK OF VIRUSES, ACCURACY OR COMPLETENESS, QUIET ENJOYMENT, +* QUIET POSSESSION OR CORRESPONDENCE TO DESCRIPTION. THE ENTIRE RISK +* ARISING OUT OF USE OR PERFORMANCE OF THE SOFTWARE LIES WITH YOU. +***********************license end**************************************/ + +/** + * @file + * + * Interface to the SPI / MPI bus + * + * <hr>$Revision: 49448 $<hr> + * + * @addtogroup hal + * @{ + */ + +typedef enum +{ + BDK_MPI_FLAGS_ENABLE_CS0 = 1<<0, /**< Chip select 0 will be needed */ + BDK_MPI_FLAGS_ENABLE_CS1 = 1<<1, /**< Chip select 1 will be needed */ + BDK_MPI_FLAGS_ENABLE_CS2 = 1<<2, /**< Chip select 2 will be needed */ + BDK_MPI_FLAGS_ENABLE_CS3 = 1<<3, /**< Chip select 3 will be needed */ + BDK_MPI_FLAGS_CS_ACTIVE_HI = 1<<4, /**< Chip select is active high, else active low */ + BDK_MPI_FLAGS_ONE_WIRE = 1<<5, /**< Input and output are multiplexed over SPI_DO */ + BDK_MPI_FLAGS_IDLE_CLOCKS = 1<<7, /**< Continue to clock between commands */ + BDK_MPI_FLAGS_IDLE_LOW = 1<<8, /**< Clear the clock is idle high, Set the clock is idle low */ + BDK_MPI_FLAGS_LSB_FIRST = 1<<9, /**< Set to shift the LSB first, otherwise MSB will shift first */ +} bdk_mpi_flags_t; + +/** + * Initialize MPI/SPI for use. The different configuration + * options are encoded as bitmask inside the flags parameter. + * + * @param node Numa node to use + * @param clock_rate_hz + * Clock rate in Hz (1-16M) + * @param flags Setup flags ORed together + * + * @return Zero on success, negative on failure + */ +extern int bdk_mpi_initialize(bdk_node_t node, int clock_rate_hz, bdk_mpi_flags_t flags); + +/** + * Perform a SPI/MPI transfer. The transfer can contain tx_count + * bytes that are transferred out, followed by rx_count bytes + * that are read in. Both tx_count and rx_count may be zero if + * no transfer is needed. Transmit data is sent most significant + * byte first, unless BDK_MPI_FLAGS_LSB_FIRST is set. Receive data + * is in the return value with the last byte in the least + * signnificant byte. + * + * @param node Numa node to use + * @param chip_select + * Which chip select to enable during the transfer + * @param leave_cs_enabled + * Leave the chip select assert after the transaction. Normally can + * be zero. Set to non zero if you want to perform repeated + * transactions. + * @param tx_count Number of bytes to transfer before startng the rx/shift data. + * Can be zero. + * @param tx_data Data to transmit. The low order bytes are used for the data. Order + * of shift out is controlled by BDK_MPI_FLAGS_LSB_FIRST + * @param rx_count Number of bytes to read. These bytes will be in the return value + * least significant bytes + * + * @return Read data + */ +extern uint64_t bdk_mpi_transfer(bdk_node_t node, int chip_select, + int leave_cs_enabled, int tx_count, uint64_t tx_data, int rx_count); + +/** @} */ |