diff options
Diffstat (limited to 'src/southbridge')
| -rw-r--r-- | src/southbridge/amd/sb600/sb600_early_setup.c | 56 |
1 files changed, 41 insertions, 15 deletions
diff --git a/src/southbridge/amd/sb600/sb600_early_setup.c b/src/southbridge/amd/sb600/sb600_early_setup.c index 3ed9f53ac5..e63e8e930e 100644 --- a/src/southbridge/amd/sb600/sb600_early_setup.c +++ b/src/southbridge/amd/sb600/sb600_early_setup.c @@ -53,11 +53,17 @@ static u8 get_sb600_revision() /*************************************** * Legacy devices are mapped to LPC space. -* serial port 0 +* Serial port 0 * KBC Port * ACPI Micro-controller port -* LPC ROM size, +* LPC ROM size +* This function does not change port 0x80 decoding. +* Console output through any port besides 0x3f8 is unsupported. +* If you use FWH ROMs, you have to setup IDSEL. * NOTE: Call me ASAP, because I will reset LPC ROM size! +* Reviewed-by: Carl-Daniel Hailfinger +* Reviewed against AMD SB600 Register Reference Manual rev. 3.03, section 3.1 +* (LPC ISA Bridge) ***************************************/ static void sb600_lpc_init(void) { @@ -68,32 +74,42 @@ static void sb600_lpc_init(void) /* Enable lpc controller */ dev = pci_locate_device(PCI_ID(0x1002, 0x4385), 0); /* SMBUS controller */ reg32 = pci_read_config32(dev, 0x64); - reg32 |= 0x00100000; + reg32 |= 1 << 20; pci_write_config32(dev, 0x64, reg32); dev = pci_locate_device(PCI_ID(0x1002, 0x438d), 0); /* LPC Controller */ - /* Serial 0 */ + /* Decode port 0x3f8-0x3ff (Serial 0) */ +#warning Serial port decode on LPC is hardcoded to 0x3f8 reg8 = pci_read_config8(dev, 0x44); - reg8 |= (1 << 6); + reg8 |= 1 << 6; pci_write_config8(dev, 0x44, reg8); - /* PS/2 keyboard, ACPI */ + /* Decode port 0x60 & 0x64 (PS/2 keyboard) and port 0x62 & 0x66 (ACPI)*/ reg8 = pci_read_config8(dev, 0x47); reg8 |= (1 << 5) | (1 << 6); pci_write_config8(dev, 0x47, reg8); /* SuperIO, LPC ROM */ reg8 = pci_read_config8(dev, 0x48); - reg8 |= (1 << 1) | (1 << 0); /* enable Super IO config port 2e-2h, 4e-4f */ - reg8 |= (1 << 3) | (1 << 4); /* enable for LPC ROM address range1&2, Enable 512KB rom access at 0xFFF80000 - 0xFFFFFFFF */ - reg8 |= 1 << 6; /* enable for RTC I/O range */ + /* Decode ports 0x2e-0x2f, 0x4e-0x4f (SuperI/O configuration) */ + reg8 |= (1 << 1) | (1 << 0); + /* Decode variable LPC ROM address ranges 1&2 (see register 0x68-0x6b, 0x6c-0x6f) */ + reg8 |= (1 << 3) | (1 << 4); + /* Decode port 0x70-0x73 (RTC) */ + reg8 |= 1 << 6; pci_write_config8(dev, 0x48, reg8); - /* hardware should enable LPC ROM by pin strapes */ - /* rom access at 0xFFF80000/0xFFF00000 - 0xFFFFFFFF */ + /* hardware should enable LPC ROM by pin straps */ + /* ROM access at 0xFFF80000/0xFFF00000 - 0xFFFFFFFF */ /* See detail in BDG-215SB600-03.pdf page 15. */ - pci_write_config16(dev, 0x68, 0x000e); /* enable LPC ROM range, 0xfff8: 512KB, 0xfff0: 1MB; */ - pci_write_config16(dev, 0x6c, 0xfff0); /* enable LPC ROM range, 0xfff8: 512KB, 0xfff0: 1MB */ + /* enable LPC ROM range mirroring start 0x000e(0000) */ + pci_write_config16(dev, 0x68, 0x000e); + /* enable LPC ROM range mirroring end 0x000f(ffff) */ + pci_write_config16(dev, 0x6a, 0x000f); + /* enable LPC ROM range start, 0xfff8(0000): 512KB, 0xfff0(0000): 1MB */ + pci_write_config16(dev, 0x6c, 0xfff0); + /* enable LPC ROM range end at 0xffff(ffff) */ + pci_write_config16(dev, 0x6e, 0xffff); } /* what is its usage? */ @@ -201,26 +217,36 @@ static void sb600_pci_port80() /* P2P Bridge */ dev = pci_locate_device(PCI_ID(0x1002, 0x4384), 0); + /* Chip Control: Enable subtractive decoding */ byte = pci_read_config8(dev, 0x40); byte |= 1 << 5; pci_write_config8(dev, 0x40, byte); + /* Misc Control: Enable subtractive decoding if 0x40 bit 5 is set */ byte = pci_read_config8(dev, 0x4B); byte |= 1 << 7; pci_write_config8(dev, 0x4B, byte); + /* The same IO Base and IO Limit here is meaningful because we set the + * bridge to be subtractive. During early setup stage, we have to make + * sure that data can go through port 0x80. + */ + /* IO Base: 0xf000 */ byte = pci_read_config8(dev, 0x1C); byte |= 0xF << 4; pci_write_config8(dev, 0x1C, byte); + /* IO Limit: 0xf000 */ byte = pci_read_config8(dev, 0x1D); byte |= 0xF << 4; pci_write_config8(dev, 0x1D, byte); + /* PCI Command: Enable IO response */ byte = pci_read_config8(dev, 0x04); byte |= 1 << 0; pci_write_config8(dev, 0x04, byte); + /* LPC controller */ dev = pci_locate_device(PCI_ID(0x1002, 0x438D), 0); byte = pci_read_config8(dev, 0x4A); @@ -234,13 +260,13 @@ static void sb600_lpc_port80(void) device_t dev; u32 reg32; - /* enable lpc controller */ + /* Enable LPC controller */ dev = pci_locate_device(PCI_ID(0x1002, 0x4385), 0); reg32 = pci_read_config32(dev, 0x64); reg32 |= 0x00100000; /* lpcEnable */ pci_write_config32(dev, 0x64, reg32); - /* enable prot80 LPC decode in pci function 3 configuration space. */ + /* Enable port 80 LPC decode in pci function 3 configuration space. */ dev = pci_locate_device(PCI_ID(0x1002, 0x438d), 0); byte = pci_read_config8(dev, 0x4a); byte |= 1 << 5; /* enable port 80 */ |