summaryrefslogtreecommitdiff
path: root/src/southbridge
diff options
context:
space:
mode:
Diffstat (limited to 'src/southbridge')
-rw-r--r--src/southbridge/amd/sb600/sb600_early_setup.c56
1 files changed, 41 insertions, 15 deletions
diff --git a/src/southbridge/amd/sb600/sb600_early_setup.c b/src/southbridge/amd/sb600/sb600_early_setup.c
index 3ed9f53ac5..e63e8e930e 100644
--- a/src/southbridge/amd/sb600/sb600_early_setup.c
+++ b/src/southbridge/amd/sb600/sb600_early_setup.c
@@ -53,11 +53,17 @@ static u8 get_sb600_revision()
/***************************************
* Legacy devices are mapped to LPC space.
-* serial port 0
+* Serial port 0
* KBC Port
* ACPI Micro-controller port
-* LPC ROM size,
+* LPC ROM size
+* This function does not change port 0x80 decoding.
+* Console output through any port besides 0x3f8 is unsupported.
+* If you use FWH ROMs, you have to setup IDSEL.
* NOTE: Call me ASAP, because I will reset LPC ROM size!
+* Reviewed-by: Carl-Daniel Hailfinger
+* Reviewed against AMD SB600 Register Reference Manual rev. 3.03, section 3.1
+* (LPC ISA Bridge)
***************************************/
static void sb600_lpc_init(void)
{
@@ -68,32 +74,42 @@ static void sb600_lpc_init(void)
/* Enable lpc controller */
dev = pci_locate_device(PCI_ID(0x1002, 0x4385), 0); /* SMBUS controller */
reg32 = pci_read_config32(dev, 0x64);
- reg32 |= 0x00100000;
+ reg32 |= 1 << 20;
pci_write_config32(dev, 0x64, reg32);
dev = pci_locate_device(PCI_ID(0x1002, 0x438d), 0); /* LPC Controller */
- /* Serial 0 */
+ /* Decode port 0x3f8-0x3ff (Serial 0) */
+#warning Serial port decode on LPC is hardcoded to 0x3f8
reg8 = pci_read_config8(dev, 0x44);
- reg8 |= (1 << 6);
+ reg8 |= 1 << 6;
pci_write_config8(dev, 0x44, reg8);
- /* PS/2 keyboard, ACPI */
+ /* Decode port 0x60 & 0x64 (PS/2 keyboard) and port 0x62 & 0x66 (ACPI)*/
reg8 = pci_read_config8(dev, 0x47);
reg8 |= (1 << 5) | (1 << 6);
pci_write_config8(dev, 0x47, reg8);
/* SuperIO, LPC ROM */
reg8 = pci_read_config8(dev, 0x48);
- reg8 |= (1 << 1) | (1 << 0); /* enable Super IO config port 2e-2h, 4e-4f */
- reg8 |= (1 << 3) | (1 << 4); /* enable for LPC ROM address range1&2, Enable 512KB rom access at 0xFFF80000 - 0xFFFFFFFF */
- reg8 |= 1 << 6; /* enable for RTC I/O range */
+ /* Decode ports 0x2e-0x2f, 0x4e-0x4f (SuperI/O configuration) */
+ reg8 |= (1 << 1) | (1 << 0);
+ /* Decode variable LPC ROM address ranges 1&2 (see register 0x68-0x6b, 0x6c-0x6f) */
+ reg8 |= (1 << 3) | (1 << 4);
+ /* Decode port 0x70-0x73 (RTC) */
+ reg8 |= 1 << 6;
pci_write_config8(dev, 0x48, reg8);
- /* hardware should enable LPC ROM by pin strapes */
- /* rom access at 0xFFF80000/0xFFF00000 - 0xFFFFFFFF */
+ /* hardware should enable LPC ROM by pin straps */
+ /* ROM access at 0xFFF80000/0xFFF00000 - 0xFFFFFFFF */
/* See detail in BDG-215SB600-03.pdf page 15. */
- pci_write_config16(dev, 0x68, 0x000e); /* enable LPC ROM range, 0xfff8: 512KB, 0xfff0: 1MB; */
- pci_write_config16(dev, 0x6c, 0xfff0); /* enable LPC ROM range, 0xfff8: 512KB, 0xfff0: 1MB */
+ /* enable LPC ROM range mirroring start 0x000e(0000) */
+ pci_write_config16(dev, 0x68, 0x000e);
+ /* enable LPC ROM range mirroring end 0x000f(ffff) */
+ pci_write_config16(dev, 0x6a, 0x000f);
+ /* enable LPC ROM range start, 0xfff8(0000): 512KB, 0xfff0(0000): 1MB */
+ pci_write_config16(dev, 0x6c, 0xfff0);
+ /* enable LPC ROM range end at 0xffff(ffff) */
+ pci_write_config16(dev, 0x6e, 0xffff);
}
/* what is its usage? */
@@ -201,26 +217,36 @@ static void sb600_pci_port80()
/* P2P Bridge */
dev = pci_locate_device(PCI_ID(0x1002, 0x4384), 0);
+ /* Chip Control: Enable subtractive decoding */
byte = pci_read_config8(dev, 0x40);
byte |= 1 << 5;
pci_write_config8(dev, 0x40, byte);
+ /* Misc Control: Enable subtractive decoding if 0x40 bit 5 is set */
byte = pci_read_config8(dev, 0x4B);
byte |= 1 << 7;
pci_write_config8(dev, 0x4B, byte);
+ /* The same IO Base and IO Limit here is meaningful because we set the
+ * bridge to be subtractive. During early setup stage, we have to make
+ * sure that data can go through port 0x80.
+ */
+ /* IO Base: 0xf000 */
byte = pci_read_config8(dev, 0x1C);
byte |= 0xF << 4;
pci_write_config8(dev, 0x1C, byte);
+ /* IO Limit: 0xf000 */
byte = pci_read_config8(dev, 0x1D);
byte |= 0xF << 4;
pci_write_config8(dev, 0x1D, byte);
+ /* PCI Command: Enable IO response */
byte = pci_read_config8(dev, 0x04);
byte |= 1 << 0;
pci_write_config8(dev, 0x04, byte);
+ /* LPC controller */
dev = pci_locate_device(PCI_ID(0x1002, 0x438D), 0);
byte = pci_read_config8(dev, 0x4A);
@@ -234,13 +260,13 @@ static void sb600_lpc_port80(void)
device_t dev;
u32 reg32;
- /* enable lpc controller */
+ /* Enable LPC controller */
dev = pci_locate_device(PCI_ID(0x1002, 0x4385), 0);
reg32 = pci_read_config32(dev, 0x64);
reg32 |= 0x00100000; /* lpcEnable */
pci_write_config32(dev, 0x64, reg32);
- /* enable prot80 LPC decode in pci function 3 configuration space. */
+ /* Enable port 80 LPC decode in pci function 3 configuration space. */
dev = pci_locate_device(PCI_ID(0x1002, 0x438d), 0);
byte = pci_read_config8(dev, 0x4a);
byte |= 1 << 5; /* enable port 80 */