summaryrefslogtreecommitdiff
path: root/src/southbridge/intel/bd82x6x/smihandler.c
diff options
context:
space:
mode:
Diffstat (limited to 'src/southbridge/intel/bd82x6x/smihandler.c')
-rw-r--r--src/southbridge/intel/bd82x6x/smihandler.c682
1 files changed, 23 insertions, 659 deletions
diff --git a/src/southbridge/intel/bd82x6x/smihandler.c b/src/southbridge/intel/bd82x6x/smihandler.c
index bf72b5e324..e2ff851e42 100644
--- a/src/southbridge/intel/bd82x6x/smihandler.c
+++ b/src/southbridge/intel/bd82x6x/smihandler.c
@@ -33,214 +33,14 @@
#include <southbridge/intel/bd82x6x/me.h>
#include <southbridge/intel/common/gpio.h>
#include <cpu/intel/model_206ax/model_206ax.h>
+#include <southbridge/intel/common/pmutil.h>
-/* While we read PMBASE dynamically in case it changed, let's
- * initialize it with a sane value
- */
-static u16 pmbase = DEFAULT_PMBASE;
-u16 smm_get_pmbase(void)
-{
- return pmbase;
-}
-
-static u8 smm_initialized = 0;
-
-/* GNVS needs to be updated by an 0xEA PM Trap (B2) after it has been located
- * by coreboot.
- */
static global_nvs_t *gnvs;
global_nvs_t *smm_get_gnvs(void)
{
return gnvs;
}
-static void alt_gpi_mask(u16 clr, u16 set)
-{
- u16 alt_gp = inw(pmbase + ALT_GP_SMI_EN);
- alt_gp &= ~clr;
- alt_gp |= set;
- outw(alt_gp, pmbase + ALT_GP_SMI_EN);
-}
-
-static void gpe0_mask(u32 clr, u32 set)
-{
- u32 gpe0 = inl(pmbase + GPE0_EN);
- gpe0 &= ~clr;
- gpe0 |= set;
- outl(gpe0, pmbase + GPE0_EN);
-}
-
-void gpi_route_interrupt(u8 gpi, u8 mode)
-{
- u32 gpi_rout;
- if (gpi >= 16)
- return;
-
- alt_gpi_mask(1 << gpi, 0);
- gpe0_mask(1 << (gpi+16), 0);
-
- gpi_rout = pci_read_config32(PCI_DEV(0, 0x1f, 0), GPIO_ROUT);
- gpi_rout &= ~(3 << (2 * gpi));
- gpi_rout |= ((mode & 3) << (2 * gpi));
- pci_write_config32(PCI_DEV(0, 0x1f, 0), GPIO_ROUT, gpi_rout);
-
- if (mode == GPI_IS_SCI)
- gpe0_mask(0, 1 << (gpi+16));
- else if (mode == GPI_IS_SMI)
- alt_gpi_mask(0, 1 << gpi);
-}
-
-/**
- * @brief read and clear PM1_STS
- * @return PM1_STS register
- */
-static u16 reset_pm1_status(void)
-{
- u16 reg16;
-
- reg16 = inw(pmbase + PM1_STS);
- /* set status bits are cleared by writing 1 to them */
- outw(reg16, pmbase + PM1_STS);
-
- return reg16;
-}
-
-static void dump_pm1_status(u16 pm1_sts)
-{
- printk(BIOS_SPEW, "PM1_STS: ");
- if (pm1_sts & (1 << 15)) printk(BIOS_SPEW, "WAK ");
- if (pm1_sts & (1 << 14)) printk(BIOS_SPEW, "PCIEXPWAK ");
- if (pm1_sts & (1 << 11)) printk(BIOS_SPEW, "PRBTNOR ");
- if (pm1_sts & (1 << 10)) printk(BIOS_SPEW, "RTC ");
- if (pm1_sts & (1 << 8)) printk(BIOS_SPEW, "PWRBTN ");
- if (pm1_sts & (1 << 5)) printk(BIOS_SPEW, "GBL ");
- if (pm1_sts & (1 << 4)) printk(BIOS_SPEW, "BM ");
- if (pm1_sts & (1 << 0)) printk(BIOS_SPEW, "TMROF ");
- printk(BIOS_SPEW, "\n");
- int reg16 = inw(pmbase + PM1_EN);
- printk(BIOS_SPEW, "PM1_EN: %x\n", reg16);
-}
-
-/**
- * @brief read and clear SMI_STS
- * @return SMI_STS register
- */
-static u32 reset_smi_status(void)
-{
- u32 reg32;
-
- reg32 = inl(pmbase + SMI_STS);
- /* set status bits are cleared by writing 1 to them */
- outl(reg32, pmbase + SMI_STS);
-
- return reg32;
-}
-
-static void dump_smi_status(u32 smi_sts)
-{
- printk(BIOS_DEBUG, "SMI_STS: ");
- if (smi_sts & (1 << 26)) printk(BIOS_DEBUG, "SPI ");
- if (smi_sts & (1 << 21)) printk(BIOS_DEBUG, "MONITOR ");
- if (smi_sts & (1 << 20)) printk(BIOS_DEBUG, "PCI_EXP_SMI ");
- if (smi_sts & (1 << 18)) printk(BIOS_DEBUG, "INTEL_USB2 ");
- if (smi_sts & (1 << 17)) printk(BIOS_DEBUG, "LEGACY_USB2 ");
- if (smi_sts & (1 << 16)) printk(BIOS_DEBUG, "SMBUS_SMI ");
- if (smi_sts & (1 << 15)) printk(BIOS_DEBUG, "SERIRQ_SMI ");
- if (smi_sts & (1 << 14)) printk(BIOS_DEBUG, "PERIODIC ");
- if (smi_sts & (1 << 13)) printk(BIOS_DEBUG, "TCO ");
- if (smi_sts & (1 << 12)) printk(BIOS_DEBUG, "DEVMON ");
- if (smi_sts & (1 << 11)) printk(BIOS_DEBUG, "MCSMI ");
- if (smi_sts & (1 << 10)) printk(BIOS_DEBUG, "GPI ");
- if (smi_sts & (1 << 9)) printk(BIOS_DEBUG, "GPE0 ");
- if (smi_sts & (1 << 8)) printk(BIOS_DEBUG, "PM1 ");
- if (smi_sts & (1 << 6)) printk(BIOS_DEBUG, "SWSMI_TMR ");
- if (smi_sts & (1 << 5)) printk(BIOS_DEBUG, "APM ");
- if (smi_sts & (1 << 4)) printk(BIOS_DEBUG, "SLP_SMI ");
- if (smi_sts & (1 << 3)) printk(BIOS_DEBUG, "LEGACY_USB ");
- if (smi_sts & (1 << 2)) printk(BIOS_DEBUG, "BIOS ");
- printk(BIOS_DEBUG, "\n");
-}
-
-
-/**
- * @brief read and clear GPE0_STS
- * @return GPE0_STS register
- */
-static u32 reset_gpe0_status(void)
-{
- u32 reg32;
-
- reg32 = inl(pmbase + GPE0_STS);
- /* set status bits are cleared by writing 1 to them */
- outl(reg32, pmbase + GPE0_STS);
-
- return reg32;
-}
-
-static void dump_gpe0_status(u32 gpe0_sts)
-{
- int i;
- printk(BIOS_DEBUG, "GPE0_STS: ");
- for (i=31; i>= 16; i--) {
- if (gpe0_sts & (1 << i)) printk(BIOS_DEBUG, "GPIO%d ", (i-16));
- }
- if (gpe0_sts & (1 << 14)) printk(BIOS_DEBUG, "USB4 ");
- if (gpe0_sts & (1 << 13)) printk(BIOS_DEBUG, "PME_B0 ");
- if (gpe0_sts & (1 << 12)) printk(BIOS_DEBUG, "USB3 ");
- if (gpe0_sts & (1 << 11)) printk(BIOS_DEBUG, "PME ");
- if (gpe0_sts & (1 << 10)) printk(BIOS_DEBUG, "BATLOW ");
- if (gpe0_sts & (1 << 9)) printk(BIOS_DEBUG, "PCI_EXP ");
- if (gpe0_sts & (1 << 8)) printk(BIOS_DEBUG, "RI ");
- if (gpe0_sts & (1 << 7)) printk(BIOS_DEBUG, "SMB_WAK ");
- if (gpe0_sts & (1 << 6)) printk(BIOS_DEBUG, "TCO_SCI ");
- if (gpe0_sts & (1 << 5)) printk(BIOS_DEBUG, "AC97 ");
- if (gpe0_sts & (1 << 4)) printk(BIOS_DEBUG, "USB2 ");
- if (gpe0_sts & (1 << 3)) printk(BIOS_DEBUG, "USB1 ");
- if (gpe0_sts & (1 << 2)) printk(BIOS_DEBUG, "SWGPE ");
- if (gpe0_sts & (1 << 1)) printk(BIOS_DEBUG, "HOTPLUG ");
- if (gpe0_sts & (1 << 0)) printk(BIOS_DEBUG, "THRM ");
- printk(BIOS_DEBUG, "\n");
-}
-
-
-/**
- * @brief read and clear TCOx_STS
- * @return TCOx_STS registers
- */
-static u32 reset_tco_status(void)
-{
- u32 tcobase = pmbase + 0x60;
- u32 reg32;
-
- reg32 = inl(tcobase + 0x04);
- /* set status bits are cleared by writing 1 to them */
- outl(reg32 & ~(1<<18), tcobase + 0x04); // Don't clear BOOT_STS before SECOND_TO_STS
- if (reg32 & (1 << 18))
- outl(reg32 & (1<<18), tcobase + 0x04); // clear BOOT_STS
-
- return reg32;
-}
-
-
-static void dump_tco_status(u32 tco_sts)
-{
- printk(BIOS_DEBUG, "TCO_STS: ");
- if (tco_sts & (1 << 20)) printk(BIOS_DEBUG, "SMLINK_SLV ");
- if (tco_sts & (1 << 18)) printk(BIOS_DEBUG, "BOOT ");
- if (tco_sts & (1 << 17)) printk(BIOS_DEBUG, "SECOND_TO ");
- if (tco_sts & (1 << 16)) printk(BIOS_DEBUG, "INTRD_DET ");
- if (tco_sts & (1 << 12)) printk(BIOS_DEBUG, "DMISERR ");
- if (tco_sts & (1 << 10)) printk(BIOS_DEBUG, "DMISMI ");
- if (tco_sts & (1 << 9)) printk(BIOS_DEBUG, "DMISCI ");
- if (tco_sts & (1 << 8)) printk(BIOS_DEBUG, "BIOSWR ");
- if (tco_sts & (1 << 7)) printk(BIOS_DEBUG, "NEWCENTURY ");
- if (tco_sts & (1 << 3)) printk(BIOS_DEBUG, "TIMEOUT ");
- if (tco_sts & (1 << 2)) printk(BIOS_DEBUG, "TCO_INT ");
- if (tco_sts & (1 << 1)) printk(BIOS_DEBUG, "SW_TCO ");
- if (tco_sts & (1 << 0)) printk(BIOS_DEBUG, "NMI2SMI ");
- printk(BIOS_DEBUG, "\n");
-}
-
int southbridge_io_trap_handler(int smif)
{
switch (smif) {
@@ -258,53 +58,6 @@ int southbridge_io_trap_handler(int smif)
return 0;
}
-/**
- * @brief Set the EOS bit
- */
-void southbridge_smi_set_eos(void)
-{
- u8 reg8;
-
- reg8 = inb(pmbase + SMI_EN);
- reg8 |= EOS;
- outb(reg8, pmbase + SMI_EN);
-}
-
-static void busmaster_disable_on_bus(int bus)
-{
- int slot, func;
- unsigned int val;
- unsigned char hdr;
-
- for (slot = 0; slot < 0x20; slot++) {
- for (func = 0; func < 8; func++) {
- u32 reg32;
- pci_devfn_t dev = PCI_DEV(bus, slot, func);
-
- val = pci_read_config32(dev, PCI_VENDOR_ID);
-
- if (val == 0xffffffff || val == 0x00000000 ||
- val == 0x0000ffff || val == 0xffff0000)
- continue;
-
- /* Disable Bus Mastering for this one device */
- reg32 = pci_read_config32(dev, PCI_COMMAND);
- reg32 &= ~PCI_COMMAND_MASTER;
- pci_write_config32(dev, PCI_COMMAND, reg32);
-
- /* If this is a bridge, then follow it. */
- hdr = pci_read_config8(dev, PCI_HEADER_TYPE);
- hdr &= 0x7f;
- if (hdr == PCI_HEADER_TYPE_BRIDGE ||
- hdr == PCI_HEADER_TYPE_CARDBUS) {
- unsigned int buses;
- buses = pci_read_config32(dev, PCI_PRIMARY_BUS);
- busmaster_disable_on_bus((buses >> 8) & 0xff);
- }
- }
- }
-}
-
static void southbridge_gate_memory_reset_real(int offset,
u16 use, u16 io, u16 lvl)
{
@@ -336,7 +89,7 @@ static void southbridge_gate_memory_reset_real(int offset,
* Intel reference designs all use GPIO 60 but it is
* not a requirement and boards could use a different pin.
*/
-static void southbridge_gate_memory_reset(void)
+void southbridge_gate_memory_reset(void)
{
u16 gpiobase;
@@ -401,348 +154,7 @@ static void xhci_sleep(u8 slp_typ)
}
}
-
-static void southbridge_smi_sleep(void)
-{
- u8 reg8;
- u32 reg32;
- u8 slp_typ;
- u8 s5pwr = CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL;
-
- // save and recover RTC port values
- u8 tmp70, tmp72;
- tmp70 = inb(0x70);
- tmp72 = inb(0x72);
- get_option(&s5pwr, "power_on_after_fail");
- outb(tmp70, 0x70);
- outb(tmp72, 0x72);
-
- /* First, disable further SMIs */
- reg8 = inb(pmbase + SMI_EN);
- reg8 &= ~SLP_SMI_EN;
- outb(reg8, pmbase + SMI_EN);
-
- /* Figure out SLP_TYP */
- reg32 = inl(pmbase + PM1_CNT);
- printk(BIOS_SPEW, "SMI#: SLP = 0x%08x\n", reg32);
- slp_typ = acpi_sleep_from_pm1(reg32);
-
- if (smm_get_gnvs()->xhci)
- xhci_sleep(slp_typ);
-
- /* Do any mainboard sleep handling */
- mainboard_smi_sleep(slp_typ);
-
-#if IS_ENABLED(CONFIG_ELOG_GSMI)
- /* Log S3, S4, and S5 entry */
- if (slp_typ >= ACPI_S3)
- elog_add_event_byte(ELOG_TYPE_ACPI_ENTER, slp_typ);
-#endif
-
- /* Next, do the deed.
- */
-
- switch (slp_typ) {
- case ACPI_S0: printk(BIOS_DEBUG, "SMI#: Entering S0 (On)\n"); break;
- case ACPI_S1: printk(BIOS_DEBUG, "SMI#: Entering S1 (Assert STPCLK#)\n"); break;
- case ACPI_S3:
- printk(BIOS_DEBUG, "SMI#: Entering S3 (Suspend-To-RAM)\n");
-
- /* Gate memory reset */
- southbridge_gate_memory_reset();
-
- /* Invalidate the cache before going to S3 */
- wbinvd();
- break;
- case ACPI_S4: printk(BIOS_DEBUG, "SMI#: Entering S4 (Suspend-To-Disk)\n"); break;
- case ACPI_S5:
- printk(BIOS_DEBUG, "SMI#: Entering S5 (Soft Power off)\n");
-
- outl(0, pmbase + GPE0_EN);
-
- /* Always set the flag in case CMOS was changed on runtime. For
- * "KEEP", switch to "OFF" - KEEP is software emulated
- */
- reg8 = pci_read_config8(PCI_DEV(0, 0x1f, 0), GEN_PMCON_3);
- if (s5pwr == MAINBOARD_POWER_ON) {
- reg8 &= ~1;
- } else {
- reg8 |= 1;
- }
- pci_write_config8(PCI_DEV(0, 0x1f, 0), GEN_PMCON_3, reg8);
-
- /* also iterates over all bridges on bus 0 */
- busmaster_disable_on_bus(0);
- break;
- default: printk(BIOS_DEBUG, "SMI#: ERROR: SLP_TYP reserved\n"); break;
- }
-
- /* Write back to the SLP register to cause the originally intended
- * event again. We need to set BIT13 (SLP_EN) though to make the
- * sleep happen.
- */
- outl(reg32 | SLP_EN, pmbase + PM1_CNT);
-
- /* Make sure to stop executing code here for S3/S4/S5 */
- if (slp_typ >= ACPI_S3)
- halt();
-
- /* In most sleep states, the code flow of this function ends at
- * the line above. However, if we entered sleep state S1 and wake
- * up again, we will continue to execute code in this function.
- */
- reg32 = inl(pmbase + PM1_CNT);
- if (reg32 & SCI_EN) {
- /* The OS is not an ACPI OS, so we set the state to S0 */
- reg32 &= ~(SLP_EN | SLP_TYP);
- outl(reg32, pmbase + PM1_CNT);
- }
-}
-
-/*
- * Look for Synchronous IO SMI and use save state from that
- * core in case we are not running on the same core that
- * initiated the IO transaction.
- */
-static em64t101_smm_state_save_area_t *smi_apmc_find_state_save(u8 cmd)
-{
- em64t101_smm_state_save_area_t *state;
- int node;
-
- /* Check all nodes looking for the one that issued the IO */
- for (node = 0; node < CONFIG_MAX_CPUS; node++) {
- state = smm_get_save_state(node);
-
- /* Check for Synchronous IO (bit0==1) */
- if (!(state->io_misc_info & (1 << 0)))
- continue;
-
- /* Make sure it was a write (bit4==0) */
- if (state->io_misc_info & (1 << 4))
- continue;
-
- /* Check for APMC IO port */
- if (((state->io_misc_info >> 16) & 0xff) != APM_CNT)
- continue;
-
- /* Check AX against the requested command */
- if ((state->rax & 0xff) != cmd)
- continue;
-
- return state;
- }
-
- return NULL;
-}
-
-#if IS_ENABLED(CONFIG_ELOG_GSMI)
-static void southbridge_smi_gsmi(void)
-{
- u32 *ret, *param;
- u8 sub_command;
- em64t101_smm_state_save_area_t *io_smi =
- smi_apmc_find_state_save(ELOG_GSMI_APM_CNT);
-
- if (!io_smi)
- return;
-
- /* Command and return value in EAX */
- ret = (u32*)&io_smi->rax;
- sub_command = (u8)(*ret >> 8);
-
- /* Parameter buffer in EBX */
- param = (u32*)&io_smi->rbx;
-
- /* drivers/elog/gsmi.c */
- *ret = gsmi_exec(sub_command, param);
-}
-#endif
-
-static int mainboard_finalized = 0;
-
-static void southbridge_smi_apmc(void)
-{
- u32 pmctrl;
- u8 reg8;
- em64t101_smm_state_save_area_t *state;
-
- /* Emulate B2 register as the FADT / Linux expects it */
-
- reg8 = inb(APM_CNT);
- switch (reg8) {
- case APM_CNT_CST_CONTROL:
- /* Calling this function seems to cause
- * some kind of race condition in Linux
- * and causes a kernel oops
- */
- printk(BIOS_DEBUG, "C-state control\n");
- break;
- case APM_CNT_PST_CONTROL:
- /* Calling this function seems to cause
- * some kind of race condition in Linux
- * and causes a kernel oops
- */
- printk(BIOS_DEBUG, "P-state control\n");
- break;
- case APM_CNT_ACPI_DISABLE:
- pmctrl = inl(pmbase + PM1_CNT);
- pmctrl &= ~SCI_EN;
- outl(pmctrl, pmbase + PM1_CNT);
- printk(BIOS_DEBUG, "SMI#: ACPI disabled.\n");
- break;
- case APM_CNT_ACPI_ENABLE:
- pmctrl = inl(pmbase + PM1_CNT);
- pmctrl |= SCI_EN;
- outl(pmctrl, pmbase + PM1_CNT);
- printk(BIOS_DEBUG, "SMI#: ACPI enabled.\n");
- break;
- case APM_CNT_GNVS_UPDATE:
- if (smm_initialized) {
- printk(BIOS_DEBUG, "SMI#: SMM structures already initialized!\n");
- return;
- }
- state = smi_apmc_find_state_save(reg8);
- if (state) {
- /* EBX in the state save contains the GNVS pointer */
- gnvs = (global_nvs_t *)((u32)state->rbx);
- smm_initialized = 1;
- printk(BIOS_DEBUG, "SMI#: Setting GNVS to %p\n", gnvs);
- }
- break;
- case APM_CNT_FINALIZE:
- if (mainboard_finalized) {
- printk(BIOS_DEBUG, "SMI#: Already finalized\n");
- return;
- }
-
- intel_me_finalize_smm();
- intel_pch_finalize_smm();
- intel_sandybridge_finalize_smm();
- intel_model_206ax_finalize_smm();
-
- mainboard_finalized = 1;
- break;
-#if IS_ENABLED(CONFIG_ELOG_GSMI)
- case ELOG_GSMI_APM_CNT:
- southbridge_smi_gsmi();
- break;
-#endif
- }
-
- mainboard_smi_apmc(reg8);
-}
-
-static void southbridge_smi_pm1(void)
-{
- u16 pm1_sts;
-
- pm1_sts = reset_pm1_status();
- dump_pm1_status(pm1_sts);
-
- /* While OSPM is not active, poweroff immediately
- * on a power button event.
- */
- if (pm1_sts & PWRBTN_STS) {
- // power button pressed
- u32 reg32;
- reg32 = (7 << 10) | (1 << 13);
-#if IS_ENABLED(CONFIG_ELOG_GSMI)
- elog_add_event(ELOG_TYPE_POWER_BUTTON);
-#endif
- outl(reg32, pmbase + PM1_CNT);
- }
-}
-
-static void southbridge_smi_gpe0(void)
-{
- u32 gpe0_sts;
-
- gpe0_sts = reset_gpe0_status();
- dump_gpe0_status(gpe0_sts);
-}
-
-static void southbridge_smi_gpi(void)
-{
- u16 reg16;
- reg16 = inw(pmbase + ALT_GP_SMI_STS);
- outw(reg16, pmbase + ALT_GP_SMI_STS);
-
- reg16 &= inw(pmbase + ALT_GP_SMI_EN);
-
- mainboard_smi_gpi(reg16);
-
- if (reg16)
- printk(BIOS_DEBUG, "GPI (mask %04x)\n", reg16);
-
- outw(reg16, pmbase + ALT_GP_SMI_STS);
-}
-
-static void southbridge_smi_mc(void)
-{
- u32 reg32;
-
- reg32 = inl(pmbase + SMI_EN);
-
- /* Are periodic SMIs enabled? */
- if ((reg32 & MCSMI_EN) == 0)
- return;
-
- printk(BIOS_DEBUG, "Microcontroller SMI.\n");
-}
-
-
-
-static void southbridge_smi_tco(void)
-{
- u32 tco_sts;
-
- tco_sts = reset_tco_status();
-
- /* Any TCO event? */
- if (!tco_sts)
- return;
-
- if (tco_sts & (1 << 8)) { // BIOSWR
- u8 bios_cntl;
-
- bios_cntl = pci_read_config16(PCI_DEV(0, 0x1f, 0), 0xdc);
-
- if (bios_cntl & 1) {
- /* BWE is RW, so the SMI was caused by a
- * write to BWE, not by a write to the BIOS
- */
-
- /* This is the place where we notice someone
- * is trying to tinker with the BIOS. We are
- * trying to be nice and just ignore it. A more
- * resolute answer would be to power down the
- * box.
- */
- printk(BIOS_DEBUG, "Switching back to RO\n");
- pci_write_config32(PCI_DEV(0, 0x1f, 0), 0xdc, (bios_cntl & ~1));
- } /* No else for now? */
- } else if (tco_sts & (1 << 3)) { /* TIMEOUT */
- /* Handle TCO timeout */
- printk(BIOS_DEBUG, "TCO Timeout.\n");
- } else if (!tco_sts) {
- dump_tco_status(tco_sts);
- }
-}
-
-static void southbridge_smi_periodic(void)
-{
- u32 reg32;
-
- reg32 = inl(pmbase + SMI_EN);
-
- /* Are periodic SMIs enabled? */
- if ((reg32 & PERIODIC_EN) == 0)
- return;
-
- printk(BIOS_DEBUG, "Periodic SMI.\n");
-}
-
-static void southbridge_smi_monitor(void)
+void southbridge_smi_monitor(void)
{
#define IOTRAP(x) (trap_sts & (1 << x))
u32 trap_sts, trap_cycle;
@@ -796,76 +208,28 @@ static void southbridge_smi_monitor(void)
#undef IOTRAP
}
-typedef void (*smi_handler_t)(void);
-
-static smi_handler_t southbridge_smi[32] = {
- NULL, // [0] reserved
- NULL, // [1] reserved
- NULL, // [2] BIOS_STS
- NULL, // [3] LEGACY_USB_STS
- southbridge_smi_sleep, // [4] SLP_SMI_STS
- southbridge_smi_apmc, // [5] APM_STS
- NULL, // [6] SWSMI_TMR_STS
- NULL, // [7] reserved
- southbridge_smi_pm1, // [8] PM1_STS
- southbridge_smi_gpe0, // [9] GPE0_STS
- southbridge_smi_gpi, // [10] GPI_STS
- southbridge_smi_mc, // [11] MCSMI_STS
- NULL, // [12] DEVMON_STS
- southbridge_smi_tco, // [13] TCO_STS
- southbridge_smi_periodic, // [14] PERIODIC_STS
- NULL, // [15] SERIRQ_SMI_STS
- NULL, // [16] SMBUS_SMI_STS
- NULL, // [17] LEGACY_USB2_STS
- NULL, // [18] INTEL_USB2_STS
- NULL, // [19] reserved
- NULL, // [20] PCI_EXP_SMI_STS
- southbridge_smi_monitor, // [21] MONITOR_STS
- NULL, // [22] reserved
- NULL, // [23] reserved
- NULL, // [24] reserved
- NULL, // [25] EL_SMI_STS
- NULL, // [26] SPI_STS
- NULL, // [27] reserved
- NULL, // [28] reserved
- NULL, // [29] reserved
- NULL, // [30] reserved
- NULL // [31] reserved
-};
-
-/**
- * @brief Interrupt handler for SMI#
- * @param node
- * @param state_save
- */
-void southbridge_smi_handler(void)
+void southbridge_smm_xhci_sleep(u8 slp_type)
{
- int i, dump = 0;
- u32 smi_sts;
-
- /* Update global variable pmbase */
- pmbase = pci_read_config16(PCI_DEV(0, 0x1f, 0), 0x40) & 0xfffc;
-
- /* We need to clear the SMI status registers, or we won't see what's
- * happening in the following calls.
- */
- smi_sts = reset_smi_status();
-
- /* Call SMI sub handler for each of the status bits */
- for (i = 0; i < 31; i++) {
- if (smi_sts & (1 << i)) {
- if (southbridge_smi[i]) {
- southbridge_smi[i]();
- } else {
- printk(BIOS_DEBUG, "SMI_STS[%d] occurred, but no "
- "handler available.\n", i);
- dump = 1;
- }
- }
- }
+ if (smm_get_gnvs()->xhci)
+ xhci_sleep(slp_type);
+}
- if (dump) {
- dump_smi_status(smi_sts);
+void southbridge_update_gnvs(u8 apm_cnt, int *smm_done)
+{
+ em64t101_smm_state_save_area_t *state =
+ smi_apmc_find_state_save(apm_cnt);
+ if (state) {
+ /* EBX in the state save contains the GNVS pointer */
+ gnvs = (global_nvs_t *)((u32)state->rbx);
+ *smm_done = 1;
+ printk(BIOS_DEBUG, "SMI#: Setting GNVS to %p\n", gnvs);
}
+}
+void southbridge_finalize_all(void)
+{
+ intel_me_finalize_smm();
+ intel_pch_finalize_smm();
+ intel_sandybridge_finalize_smm();
+ intel_model_206ax_finalize_smm();
}
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-14 03:35:39 +0000