diff options
Diffstat (limited to 'src/southbridge/amd/rs780/gfx.c')
| -rw-r--r-- | src/southbridge/amd/rs780/gfx.c | 16 |
1 files changed, 8 insertions, 8 deletions
diff --git a/src/southbridge/amd/rs780/gfx.c b/src/southbridge/amd/rs780/gfx.c index 2825925534..30a5c69a10 100644 --- a/src/southbridge/amd/rs780/gfx.c +++ b/src/southbridge/amd/rs780/gfx.c @@ -19,7 +19,7 @@ /* * for rs780 internal graphics device - * device id of internal grphics: + * device id of internal graphics: * RS780: 0x9610 * RS780C: 0x9611 * RS780M: 0x9612 @@ -355,7 +355,7 @@ static void internal_gfx_pci_dev_init(struct device *dev) static const u16 memclk_lookup_fam0F [] = {100, 0, 133, 0, 0, 166, 0, 200}; static const u16 memclk_lookup_fam10 [] = {200, 266, 333, 400, 533, 667, 800, 800}; - /* We definetely will use this in future. Just leave it here. */ + /* We definitely will use this in future. Just leave it here. */ /*struct southbridge_amd_rs780_config *cfg = (struct southbridge_amd_rs780_config *)dev->chip_info;*/ @@ -961,7 +961,7 @@ static void rs780_internal_gfx_enable(device_t dev) set_nbmc_enable_bits(nb_dev, 0xa1, 0x0ff, 0x044); set_nbmc_enable_bits(nb_dev, 0xb4, 0xf00, 0xb00); #if 0 - /* Controller Termation. */ + /* Controller Termination. */ set_nbmc_enable_bits(nb_dev, 0xb1, 0x77770000, 0x77770000); #endif @@ -1124,8 +1124,8 @@ static void dual_port_configuration(device_t nb_dev, device_t dev) if (!result) { /* Powers down all lanes for port A */ /* nbpcie_ind_write_index(nb_dev, 0x65, 0x0f0f); */ - /* Note: I have to disable the slot where there isnt a device, - * otherwise the system will hang. I dont know why. */ + /* Note: I have to disable the slot where there isn't a device, + * otherwise the system will hang. I don't know why. */ set_nbmisc_enable_bits(nb_dev, 0x0c, 1 << dev_ind, 1 << dev_ind); } else { /* step 16.b Link Training was successful */ @@ -1423,7 +1423,7 @@ void rs780_gfx_init(device_t nb_dev, device_t dev, u32 port) /* done by enable_pci_bar3() before */ /* step 7 compliance state, (only need if CMOS option is enabled) */ - /* the compliance stete is just for test. refer to 4.2.5.2 of PCIe specification */ + /* the compliance state is just for test. refer to 4.2.5.2 of PCIe specification */ if (cfg->gfx_compliance) { /* force compliance */ set_nbmisc_enable_bits(nb_dev, 0x32, 1 << 6, 1 << 6); @@ -1452,7 +1452,7 @@ void rs780_gfx_init(device_t nb_dev, device_t dev, u32 port) /* 5.9.12.6. Disables RC ordering logic */ set_pcie_enable_bits(nb_dev, 0x20, 1 << 9, 1 << 9); - /* Enabels TLP flushing. */ + /* Enables TLP flushing. */ /* Note: It is got from RS690. The system will hang without this action. */ set_pcie_enable_bits(dev, 0x20, 1 << 19, 0 << 19); @@ -1530,7 +1530,7 @@ void rs780_gfx_init(device_t nb_dev, device_t dev, u32 port) 1 << 0 | 0x1F << 1 | 0x1F << 6, 1 << 0 | 0x04 << 1 | 0x04 << 6); - /* Single-port/Dual-port configureation. */ + /* Single-port/Dual-port configuration. */ switch (cfg->gfx_dual_slot) { case 0: /* step 1, lane reversal (only need if build config option is enabled) */ |