diff options
Diffstat (limited to 'src/southbridge/amd/cs5536/cs5536.c')
-rw-r--r-- | src/southbridge/amd/cs5536/cs5536.c | 689 |
1 files changed, 558 insertions, 131 deletions
diff --git a/src/southbridge/amd/cs5536/cs5536.c b/src/southbridge/amd/cs5536/cs5536.c index 47958dba6a..e5f9878ab7 100644 --- a/src/southbridge/amd/cs5536/cs5536.c +++ b/src/southbridge/amd/cs5536/cs5536.c @@ -1,3 +1,21 @@ +/* +* This file is part of the LinuxBIOS project. +* +* Copyright (C) 2007 Advanced Micro Devices +* +* This program is free software; you can redistribute it and/or modify +* it under the terms of the GNU General Public License version 2 as +* published by the Free Software Foundation. +* +* This program is distributed in the hope that it will be useful, +* but WITHOUT ANY WARRANTY; without even the implied warranty of +* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +* GNU General Public License for more details. +* +* You should have received a copy of the GNU General Public License +* along with this program; if not, write to the Free Software +* Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA +*/ #include <arch/io.h> #include <device/device.h> @@ -5,167 +23,575 @@ #include <device/pci_ops.h> #include <device/pci_ids.h> #include <console/console.h> -#include <cpu/amd/gx2def.h> +#include <stdint.h> +#include <pc80/isa-dma.h> +#include <pc80/mc146818rtc.h> #include <cpu/x86/msr.h> +#include <cpu/amd/vr.h> +#include <cpu/amd/geode_post_code.h> #include "chip.h" +#include "cs5536.h" +extern void setup_i8259(void); -#define PIN_OPT_IDE (1ULL<<0) /* 0 for flash, 1 for IDE */ +struct msrinit { + uint32_t msrnum; + msr_t msr; +}; -/* Intended value for LBAR_FLSH0: 4KiB, enabled, MMIO, NAND, @0x20000000 */ -/* NOTE: no longer used, prune at some point */ -/* OOPS: steve's changes don't work, so we have to keep this */ -msr_t flsh0 = { .hi=0xFFFFF007, .lo=0x20000000}; +/* Master Configuration Register for Bus Masters.*/ +struct msrinit SB_MASTER_CONF_TABLE[] = { + {USB2_SB_GLD_MSR_CONF, {.hi=0,.lo=0x00008f000}}, + {ATA_SB_GLD_MSR_CONF, {.hi=0,.lo=0x00048f000}}, + {AC97_SB_GLD_MSR_CONF, {.hi=0,.lo=0x00008f000}}, + {MDD_SB_GLD_MSR_CONF, {.hi=0,.lo=0x00000f000}}, + {0,{0,0}} +}; -static void -enable_ide_nand_flash(){ - msr_t msr; - printk_err("cs5536: %s\n", __FUNCTION__); -#if 1 - printk_err("WARNING: using deprecated flash enable mechanism\n"); - /* steve took this one out ... not sure if needed or not */ - msr = rdmsr(MDD_LBAR_FLSH0); - - if ( ((msr.hi) & 7) != 7) { - printk_err("MDD_LBAR_FLSH0 was 0x%08x%08x\n", msr.hi,msr.lo); - wrmsr(MDD_LBAR_FLSH0, flsh0); - } - msr = rdmsr(MDD_LBAR_FLSH0); - printk_err("MDD_LBAR_FLSH0 is 0x%08x%08x\n", msr.hi,msr.lo); -#endif - msr = rdmsr(MDD_PIN_OPT); - if (msr.lo & PIN_OPT_IDE) { - printk_err("MDD_PIN_OPT was 0x%08x%08x\n", msr.hi,msr.lo); - msr.lo &= ~PIN_OPT_IDE; - wrmsr(MDD_PIN_OPT, msr); - } - msr = rdmsr(MDD_PIN_OPT); - printk_err("MDD_PIN_OPT is 0x%08x%08x\n", msr.hi,msr.lo); - - msr = rdmsr(MDD_NANDF_DATA); - if (msr.lo != 0x00100010) { - printk_err("MDD_NANDF_DATA was 0x%08x%08x\n", msr.hi,msr.lo); - msr.lo = 0x00100010; - wrmsr(MDD_NANDF_DATA, msr); - } - msr = rdmsr(MDD_NANDF_DATA); - printk_err("MDD_NANDF_DATA is 0x%08x%08x\n", msr.hi,msr.lo); - - msr = rdmsr(MDD_NADF_CNTL); - if (msr.lo != 0x0010) { - printk_err("MDD_NADF_CNTL was 0x%08x%08x\n", msr.hi,msr.lo); - msr.lo = 0x0010; - wrmsr(MDD_NADF_CNTL, msr); - } - msr = rdmsr(MDD_NADF_CNTL); - printk_err("MDD_NADF_CNTL is 0x%08x%08x\n", msr.hi,msr.lo); - printk_err("cs5536: EXIT %s\n", __FUNCTION__); +/* 5536 Clock Gating*/ +struct msrinit CS5536_CLOCK_GATING_TABLE[] = { +/* MSR Setting*/ + {GLIU_SB_GLD_MSR_PM, {.hi=0,.lo=0x000000004}}, + {GLPCI_SB_GLD_MSR_PM, {.hi=0,.lo=0x000000005}}, + {GLCP_SB_GLD_MSR_PM, {.hi=0,.lo=0x000000004}}, + {MDD_SB_GLD_MSR_PM, {.hi=0,.lo=0x050554111}}, /* SMBus clock gating errata (PBZ 2226 & SiBZ 3977)*/ + {ATA_SB_GLD_MSR_PM, {.hi=0,.lo=0x000000005}}, + {AC97_SB_GLD_MSR_PM, {.hi=0,.lo=0x000000005}}, + {0,{0,0}} +}; + +struct acpiinit { + uint16_t ioreg; + uint32_t regdata; +}; + +struct acpiinit acpi_init_table[] = { + {ACPI_IO_BASE + 0x00, 0x01000000}, + {ACPI_IO_BASE + 0x08, 0}, + {ACPI_IO_BASE + 0x0C, 0}, + {ACPI_IO_BASE + 0x1C, 0}, + {ACPI_IO_BASE + 0x18, 0x0FFFFFFFF}, + {ACPI_IO_BASE + 0x00, 0x0000FFFF}, + {PMS_IO_BASE + PM_SCLK, 0x000000E00}, + {PMS_IO_BASE + PM_SED, 0x000004601}, + {PMS_IO_BASE + PM_SIDD, 0x000008C02}, + {PMS_IO_BASE + PM_WKD, 0x0000000A0}, + {PMS_IO_BASE + PM_WKXD, 0x0000000A0}, + {0,0,0} +}; + +struct FLASH_DEVICE { + unsigned char fType; /* Flash type: NOR or NAND */ + unsigned char fInterface; /* Flash interface: I/O or Memory */ + unsigned long fMask; /* Flash size/mask */ +}; + +struct FLASH_DEVICE FlashInitTable[] = { + { FLASH_TYPE_NAND, FLASH_IF_MEM, FLASH_MEM_4K }, /* CS0, or Flash Device 0 */ + { FLASH_TYPE_NONE, 0, 0 }, /* CS1, or Flash Device 1 */ + { FLASH_TYPE_NONE, 0, 0 }, /* CS2, or Flash Device 2 */ + { FLASH_TYPE_NONE, 0, 0 }, /* CS3, or Flash Device 3 */ +}; + +#define FlashInitTableLen (sizeof(FlashInitTable)/sizeof(FlashInitTable[0])) + +uint32_t FlashPort[] = { + MDD_LBAR_FLSH0, + MDD_LBAR_FLSH1, + MDD_LBAR_FLSH2, + MDD_LBAR_FLSH3 + }; + + +/* ***************************************************************************/ +/* **/ +/* * pmChipsetInit*/ +/* **/ +/* * Program ACPI LBAR and initialize ACPI registers.*/ +/* **/ +/* ***************************************************************************/ +static void pmChipsetInit(void) { + uint32_t val = 0; + uint16_t port; + + port = (PMS_IO_BASE + 0x010); + val = 0x0E00 ; /* 1ms*/ + outl(val, port); + + /* PM_WKXD*/ + /* Make sure bits[3:0]=0000b to clear the*/ + /* saved Sx state*/ + port = (PMS_IO_BASE + 0x034); + val = 0x0A0 ; /* 5ms*/ + outl(val, port); + + /* PM_WKD*/ + port = (PMS_IO_BASE + 0x030); + outl(val, port); + + /* PM_SED*/ + port = (PMS_IO_BASE + 0x014); +/* mov eax, 0x057642 ; 100ms, works*/ + val = 0x04601 ; /* 5ms*/ + outl(val, port); + + /* PM_SIDD*/ + port = (PMS_IO_BASE + 0x020); +/* mov eax, 0x0AEC84 ; 200ms, works*/ + val = 0x08C02 ; /* 10ms*/ + outl(val, port); } -#if 0 -/* note: this is a candidate for inclusion in src/devices/pci_device.c */ -void -setup_irq(unsigned irq, char *name, unsigned level, unsigned bus, unsigned device, unsigned fn){ - if (irq) { - unsigned devfn = PCI_DEVFN(device,fn); - device_t dev = dev_find_slot(bus, devfn); - if (dev) { - pci_write_config8(dev, PCI_INTERRUPT_LINE, irq); - if (level) - pci_level_irq(irq); + +/*************************************************************************** + * + * ChipsetFlashSetup + * + * Flash LBARs need to be setup before VSA init so the PCI BARs have + * correct size info. Call this routine only if flash needs to be + * configured (don't call it if you want IDE). + * + **************************************************************************/ +static void ChipsetFlashSetup(void){ + msr_t msr; + int i; + int numEnabled = 0; + + printk_debug("ChipsetFlashSetup: Start\n"); + for (i = 0; i < FlashInitTableLen; i++) { + if (FlashInitTable[i].fType != FLASH_TYPE_NONE) { + printk_debug("Enable CS%d\n", i); + /* we need to configure the memory/IO mask */ + msr = rdmsr(FlashPort[i]); + msr.hi = 0; /* start with the "enabled" bit clear */ + if (FlashInitTable[i].fType == FLASH_TYPE_NAND) + msr.hi |= 0x00000002; + else + msr.hi &= ~0x00000002; + if (FlashInitTable[i].fInterface == FLASH_IF_MEM) + msr.hi |= 0x00000004; + else + msr.hi &= ~0x00000004; + msr.hi |= FlashInitTable[i].fMask; + printk_debug("MSR(0x%08X, %08X_%08X)\n", FlashPort[i], msr.hi, msr.lo); + wrmsr(FlashPort[i], msr); + + /* now write-enable the device */ + msr = rdmsr(MDD_NORF_CNTRL); + msr.lo |= (1 << i); + printk_debug("MSR(0x%08X, %08X_%08X)\n", MDD_NORF_CNTRL, msr.hi, msr.lo); + wrmsr(MDD_NORF_CNTRL, msr); + + /* update the number enabled */ + numEnabled++; } - else - printk_err("%s: Can't find %s at 0x%x\n", __FUNCTION__, name, devfn); } + + printk_debug("ChipsetFlashSetup: Finish\n"); + +} +/* ***************************************************************************/ +/* **/ +/* * enable_ide_nand_flash_header */ +/* Run after VSA init to enable the flash PCI device header */ +/* **/ +/* ***************************************************************************/ +static void enable_ide_nand_flash_header(){ + /* Tell VSA to use FLASH PCI header. Not IDE header.*/ + outl(0x80007A40, 0xCF8); + outl(0xDEADBEEF, 0xCFC); } -#endif -static void southbridge_init(struct device *dev) -{ - struct southbridge_amd_cs5536_config *sb = (struct southbridge_amd_cs5536_config *)dev->chip_info; - const unsigned char slots_cpu[4] = {11, 0, 0, 0}; - const unsigned char slots_sb[4] = {11, 5, 10, 10}; - msr_t msr; - int i; - /* - * struct device *gpiodev; - * unsigned short gpiobase = MDD_GPIO; - */ - printk_err("cs5536: %s\n", __FUNCTION__); - setup_i8259(); +#define RTC_CENTURY 0x32 +#define RTC_DOMA 0x3D +#define RTC_MONA 0x3E + +static void lpc_init(struct southbridge_amd_cs5536_config *sb){ + msr_t msr; if (sb->lpc_serirq_enable) { msr.lo = sb->lpc_serirq_enable; - msr.hi = 0; - wrmsr(MDD_LPC_SIRQ, msr); - } - if (sb->lpc_irq) { - msr.lo = sb->lpc_irq; msr.hi = 0; wrmsr(MDD_IRQM_LPC, msr); + if (sb->lpc_serirq_polarity) { + msr.lo = sb->lpc_serirq_polarity << 16; + msr.lo |= (sb->lpc_serirq_mode << 6) | (1 << 7); /* enable */ + msr.hi = 0; + wrmsr(MDD_LPC_SIRQ, msr); + } + } + + /* Allow DMA from LPC */ + msr = rdmsr(MDD_DMA_MAP); + msr.lo = 0x7777; + wrmsr(MDD_DMA_MAP, msr); + + /* enable the RTC/CMOS century byte at address 32h */ + msr = rdmsr(MDD_RTC_CENTURY_OFFSET); + msr.lo = RTC_CENTURY; + wrmsr(MDD_RTC_CENTURY_OFFSET, msr); + + /* enable the RTC/CMOS day of month and month alarms */ + msr = rdmsr(MDD_RTC_DOMA_IND); + msr.lo = RTC_DOMA; + wrmsr(MDD_RTC_DOMA_IND, msr); + + msr = rdmsr(MDD_RTC_MONA_IND); + msr.lo = RTC_MONA; + wrmsr(MDD_RTC_MONA_IND, msr); + + rtc_init(0); + + isa_dma_init(); +} + + +static void uarts_init(struct southbridge_amd_cs5536_config *sb){ + msr_t msr; + uint16_t addr; + uint32_t gpio_addr; + device_t dev; + + dev = dev_find_device(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_CS5536_ISA, 0); + gpio_addr = pci_read_config32(dev, PCI_BASE_ADDRESS_1); + gpio_addr &= ~1; /* clear IO bit */ + printk_debug("GPIO_ADDR: %08X\n", gpio_addr); + + /* This could be extended to support IR modes */ + + /* COM1 */ + if (sb->com1_enable){ + /* Set the address */ + switch (sb->com1_address){ + case 0x3F8: + addr = 7; + break; + + case 0x3E8: + addr = 6; + break; + + case 0x2F8: + addr = 5; + break; + + case 0x2E8: + addr = 4; + break; + } + msr = rdmsr(MDD_LEG_IO); + msr.lo |= addr << 16; + wrmsr(MDD_LEG_IO,msr); + + /* Set the IRQ */ + msr = rdmsr(MDD_IRQM_YHIGH); + msr.lo |= sb->com1_irq << 24; + wrmsr(MDD_IRQM_YHIGH, msr); + + /* GPIO8 - UART1_TX */ + /* Set: Output Enable (0x4) */ + outl(GPIOL_8_SET, gpio_addr + GPIOL_OUTPUT_ENABLE); + /* Set: OUTAUX1 Select (0x10) */ + outl(GPIOL_8_SET, gpio_addr + GPIOL_OUT_AUX1_SELECT); + + /* GPIO8 - UART1_RX */ + /* Set: Input Enable (0x20) */ + outl(GPIOL_9_SET, gpio_addr + GPIOL_INPUT_ENABLE); + /* Set: INAUX1 Select (0x34) */ + outl(GPIOL_9_SET, gpio_addr + GPIOL_IN_AUX1_SELECT); + + /* Set: GPIO 8 + 9 Pull Up (0x18) */ + outl(GPIOL_8_SET | GPIOL_9_SET, gpio_addr + GPIOL_PULLUP_ENABLE); + + /* enable COM1 */ + /* Bit 1 = device enable Bit 4 = allow access to the upper banks */ + msr.lo = (1 << 4) | (1 << 1); + msr.hi = 0; + wrmsr(MDD_UART1_CONF, msr); + } + else{ + /* Reset and disable COM1 */ + msr = rdmsr(MDD_UART1_CONF); + msr.lo = 1; // reset + wrmsr(MDD_UART1_CONF, msr); + msr.lo = 0; // disabled + wrmsr(MDD_UART1_CONF, msr); - if (sb->enable_gpio0_inta){ - msr = rdmsr(MDD_IRQM_ZHIGH); - msr.lo |= 0x10; - wrmsr(MDD_IRQM_ZHIGH, msr); - /* todo: look the device up. But we know that gpiobase is 0x6100 */ - /* oh gosh, all the defines from AMD assume 6100. Don't bother looking up! */ - outl(GPIOL_0_SET|GPIOL_1_SET|GPIOL_3_SET, GPIOL_INPUT_ENABLE); - outl(GPIOL_0_SET,GPIOL_EVENTS_ENABLE); - /* magic stuff */ - outl(0x3081, GPIOL_INPUT_INVERT_ENABLE); - outl(GPIOL_0_SET, GPIO_MAPPER_X); + /* Disable the IRQ */ + msr = rdmsr(MDD_LEG_IO); + msr.lo |= ~(0xF << 16); + wrmsr(MDD_LEG_IO,msr); } - if (sb->enable_uarta){ - printk_err("cs5536: %s: enable uarta, msr MDD_IRQM_YHIGH(%x) \n", - __FUNCTION__, MDD_IRQM_YHIGH); + /* COM2 */ + if (sb->com2_enable){ + switch (sb->com2_address){ + case 0x3F8: + addr = 7; + break; + + case 0x3E8: + addr = 6; + break; + + case 0x2F8: + addr = 5; + break; + + case 0x2E8: + addr = 4; + break; + } + msr = rdmsr(MDD_LEG_IO); + msr.lo |= addr << 20; + wrmsr(MDD_LEG_IO,msr); + + + /* Set the IRQ */ msr = rdmsr(MDD_IRQM_YHIGH); - msr.lo |= 0x04000000; + msr.lo |= sb->com2_irq << 28; wrmsr(MDD_IRQM_YHIGH, msr); + + /* GPIO3 - UART2_RX */ + /* Set: Output Enable (0x4) */ + outl(GPIOL_3_SET, gpio_addr + GPIOL_OUTPUT_ENABLE); + /* Set: OUTAUX1 Select (0x10) */ + outl(GPIOL_3_SET,gpio_addr + GPIOL_OUT_AUX1_SELECT); + + /* GPIO4 - UART2_TX */ + /* Set: Input Enable (0x20) */ + outl(GPIOL_4_SET, gpio_addr + GPIOL_INPUT_ENABLE); + /* Set: INAUX1 Select (0x34) */ + outl(GPIOL_4_SET, gpio_addr + GPIOL_IN_AUX1_SELECT); + + /* Set: GPIO 3 + 3 Pull Up (0x18) */ + outl(GPIOL_3_SET | GPIOL_4_SET, gpio_addr + GPIOL_PULLUP_ENABLE); + + /* enable COM2 */ + /* Bit 1 = device enable Bit 4 = allow access to the upper banks */ + msr.lo = (1 << 4) | (1 << 1); + msr.hi = 0; + wrmsr(MDD_UART2_CONF, msr); + } + else{ + /* Reset and disable COM2 */ + msr = rdmsr(MDD_UART2_CONF); + msr.lo = 1; // reset + wrmsr(MDD_UART2_CONF, msr); + msr.lo = 0; // disabled + wrmsr(MDD_UART2_CONF, msr); - printk_err("cs5536: %s: enable_ide_nand_flash is %d\n", __FUNCTION__, sb->enable_ide_nand_flash); - if (sb->enable_ide_nand_flash) { - enable_ide_nand_flash(); + /* Disable the IRQ */ + msr = rdmsr(MDD_LEG_IO); + msr.lo |= ~(0xF << 20); + wrmsr(MDD_LEG_IO,msr); } +} + -#if 0 - /* irq handling */ - setup_irq(sb->audio_irq, "audio", 1, 0, 0xf, 2); - setup_irq(sb->usbf4_irq, "usb f4", 1, 0, 0xf, 4); - setup_irq(sb->usbf5_irq, "usb f5", 1, 0, 0xf, 5); - setup_irq(sb->usbf6_irq, "usb f6", 1, 0, 0xf, 6); - setup_irq(sb->usbf7_irq, "usb f7", 1, 0, 0xf, 7); -#else - /* CPU (80000800 = 00.01.00) */ - pci_assign_irqs(0, 0x01, slots_cpu); /* bus=0, device=0x01, slots={11,0,0,0} */ - - /* Southbridge (80007800 = 00.0F.00) */ - pci_assign_irqs(0, 0x0F, slots_sb); /* bus=0, device=0x0F, slots={11,5,10,10} */ -#endif - if (sb->enable_USBP4_host) { - unsigned long val; - unsigned long uocmux; +#define HCCPARAMS 0x08 +#define IPREG04 0xA0 + #define USB_HCCPW_SET (1 << 1) +#define UOCCAP 0x00 + #define APU_SET (1 << 15) +#define UOCMUX 0x04 + #define PMUX_HOST 0x02 + #define PMUX_DEVICE 0x03 + #define PUEN_SET (1 << 2) +#define UDCDEVCTL 0x404 + #define UDC_SD_SET (1 << 10) +#define UOCCTL 0x0C + #define PADEN_SET (1 << 7) - outl(0x80007F10, 0xCF8); - outl(0x0EFC00000, 0xCFC); - uocmux = *((unsigned long *) 0x0EFC00004); - uocmux &= ~3; - uocmux |= 2; +static void enable_USB_port4(struct southbridge_amd_cs5536_config *sb) +{ + uint32_t * bar; + msr_t msr; + device_t dev; + + + dev = dev_find_device(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_CS5536_EHCI, 0); + if(dev){ + + /* Serial Short Detect Enable */ + msr = rdmsr(USB2_SB_GLD_MSR_CONF); + msr.hi |= USB2_UPPER_SSDEN_SET; + wrmsr(USB2_SB_GLD_MSR_CONF, msr); - *((unsigned long *) 0x0EFC00004) = uocmux; + /* write to clear diag register */ + wrmsr(USB2_SB_GLD_MSR_DIAG,rdmsr(USB2_SB_GLD_MSR_DIAG)); + + bar = (uint32_t *) pci_read_config32(dev, PCI_BASE_ADDRESS_0); + + /* Make HCCPARAMS writeable */ + *(bar + IPREG04) |= USB_HCCPW_SET; + + /* ; EECP=50h, IST=01h, ASPC=1 */ + *(bar + HCCPARAMS) = 0x00005012; } + + dev = dev_find_device(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_CS5536_OTG, 0); + if(dev){ + bar = (uint32_t *) pci_read_config32(dev, PCI_BASE_ADDRESS_0); + + *(bar + UOCMUX) &= PUEN_SET; + + /* Host or Device? */ + if (sb->enable_USBP4_device) { + *(bar + UOCMUX) |= PMUX_DEVICE; + } + else{ + *(bar + UOCMUX) |= PMUX_HOST; + } + + /* Overcurrent configuration */ + if (sb->enable_USBP4_overcurrent) { + *(bar + UOCCAP) |= sb->enable_USBP4_overcurrent; + } + } + + /* PBz#6466: If the UOC(OTG) device, port 4, is configured as a device, + * then perform the following sequence: + * + * - set SD bit in DEVCTRL udc register + * - set PADEN (former OTGPADEN) bit in uoc register + * - set APU bit in uoc register */ + if (sb->enable_USBP4_device) { + dev = dev_find_device(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_CS5536_UDC, 0); + if(dev){ + bar = (uint32_t *) pci_read_config32(dev, PCI_BASE_ADDRESS_0); + *(bar + UDCDEVCTL) |= UDC_SD_SET; + + } + + dev = dev_find_device(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_CS5536_OTG, 0); + if(dev){ + bar = (uint32_t *) pci_read_config32(dev, PCI_BASE_ADDRESS_0); + *(bar + UOCCTL) |= PADEN_SET; + *(bar + UOCCAP) |= APU_SET; + } + } + + /* Disable virtual PCI UDC and OTG headers */ + dev = dev_find_device(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_CS5536_UDC, 0); + if(dev){ + pci_write_config8(dev, 0x7C, 0xDEADBEEF); + } + + dev = dev_find_device(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_CS5536_OTG, 0); + if(dev){ + pci_write_config8(dev, 0x7C, 0xDEADBEEF); + } +} + +/* ***************************************************************************/ +/* **/ +/* * ChipsetInit */ +/* Called from northbridge init (Pre-VSA). */ +/* **/ +/* ***************************************************************************/ +void chipsetinit (void){ + device_t dev; + msr_t msr; + uint32_t msrnum; + struct southbridge_amd_cs5536_config *sb = (struct southbridge_amd_cs5536_config *)dev->chip_info; + struct msrinit *csi; + + outb( P80_CHIPSET_INIT, 0x80); + + /* we hope NEVER to be in linuxbios when S3 resumes + if (! IsS3Resume()) */ + { + struct acpiinit *aci = acpi_init_table; + for(; aci->ioreg; aci++) { + outl(aci->regdata, aci->ioreg); + inl(aci->ioreg); + } + + pmChipsetInit(); + } + + + /* set hd IRQ */ + outl( GPIOL_2_SET, GPIO_IO_BASE + GPIOL_INPUT_ENABLE); + outl( GPIOL_2_SET, GPIO_IO_BASE + GPIOL_IN_AUX1_SELECT); + + /* Allow IO read and writes during a ATA DMA operation.*/ + /* This could be done in the HD rom but do it here for easier debugging.*/ + msrnum = ATA_SB_GLD_MSR_ERR; + msr = rdmsr(msrnum); + msr.lo &= ~0x100; + wrmsr(msrnum, msr); + + /* Enable Post Primary IDE.*/ + msrnum = GLPCI_SB_CTRL; + msr = rdmsr(msrnum); + msr.lo |= GLPCI_CRTL_PPIDE_SET; + wrmsr(msrnum, msr); + + + csi = SB_MASTER_CONF_TABLE; + for(; csi->msrnum; csi++){ + msr.lo = csi->msr.lo; + msr.hi = csi->msr.hi; + wrmsr(csi->msrnum, msr); // MSR - see table above + } + + /* Flash BAR size Setup*/ + printk_err("%sDoing ChipsetFlashSetup()\n", sb->enable_ide_nand_flash == 1 ? "" : "Not "); + if (sb->enable_ide_nand_flash == 1) + ChipsetFlashSetup(); + + /* */ + /* Set up Hardware Clock Gating*/ + /* */ + { + csi = CS5536_CLOCK_GATING_TABLE; + for(; csi->msrnum; csi++){ + msr.lo = csi->msr.lo; + msr.hi = csi->msr.hi; + wrmsr(csi->msrnum, msr); // MSR - see table above + } + } +} + +static void southbridge_init(struct device *dev) +{ + struct southbridge_amd_cs5536_config *sb = (struct southbridge_amd_cs5536_config *)dev->chip_info; + int i; + /* + * struct device *gpiodev; + * unsigned short gpiobase = MDD_GPIO; + */ + + printk_err("cs5536: %s\n", __FUNCTION__); + setup_i8259(); + lpc_init(sb); + uarts_init(sb); + + if (sb->enable_gpio_int_route){ + vrWrite((VRC_MISCELLANEOUS << 8) + PCI_INT_AB, (sb->enable_gpio_int_route & 0xFFFF)); + vrWrite((VRC_MISCELLANEOUS << 8) + PCI_INT_CD, (sb->enable_gpio_int_route >> 16)); + } + + printk_err("cs5536: %s: enable_ide_nand_flash is %d\n", __FUNCTION__, sb->enable_ide_nand_flash); + if (sb->enable_ide_nand_flash == 1) { + enable_ide_nand_flash_header(); + } + + enable_USB_port4(sb); + /* disable unwanted virtual PCI devices */ for (i = 0; (i < MAX_UNWANTED_VPCI) && (0 != sb->unwanted_vpci[i]); i++) { printk_debug("Disabling VPCI device: 0x%08X\n", sb->unwanted_vpci[i]); outl(sb->unwanted_vpci[i] + 0x7C, 0xCF8); - outl(0xDEADBEEF, 0xCFC); + outl(0xDEADBEEF, 0xCFC); } } @@ -173,7 +599,8 @@ static void southbridge_init(struct device *dev) static void southbridge_enable(struct device *dev) { printk_err("cs5536: %s: dev is %p\n", __FUNCTION__, dev); - } + +} static void cs5536_pci_dev_enable_resources(device_t dev) { @@ -183,23 +610,23 @@ static void cs5536_pci_dev_enable_resources(device_t dev) } static struct device_operations southbridge_ops = { - .read_resources = pci_dev_read_resources, - .set_resources = pci_dev_set_resources, + .read_resources = pci_dev_read_resources, + .set_resources = pci_dev_set_resources, .enable_resources = cs5536_pci_dev_enable_resources, - .init = southbridge_init, -// .enable = southbridge_enable, - .scan_bus = scan_static_bus, + .init = southbridge_init, +// .enable = southbridge_enable, + .scan_bus = scan_static_bus, }; static struct pci_driver cs5536_pci_driver __pci_driver = { - .ops = &southbridge_ops, + .ops = &southbridge_ops, .vendor = PCI_VENDOR_ID_AMD, .device = PCI_DEVICE_ID_AMD_CS5536_ISA }; struct chip_operations southbridge_amd_cs5536_ops = { CHIP_NAME("AMD Geode CS5536 Southbridge") - /* This only called when this device is listed in the + /* This is only called when this device is listed in the * static device tree. */ .enable_dev = southbridge_enable, |