diff options
Diffstat (limited to 'src/soc/intel/baytrail')
| -rw-r--r-- | src/soc/intel/baytrail/baytrail/gpio.h | 113 |
1 files changed, 86 insertions, 27 deletions
diff --git a/src/soc/intel/baytrail/baytrail/gpio.h b/src/soc/intel/baytrail/baytrail/gpio.h index 32b991edd9..aae41a4bce 100644 --- a/src/soc/intel/baytrail/baytrail/gpio.h +++ b/src/soc/intel/baytrail/baytrail/gpio.h @@ -27,9 +27,9 @@ /* #define GPIO_DEBUG */ /* Pad base, ex. PAD_CONF0[n]= PAD_BASE+16*n */ -#define GPSCORE_PAD_BASE IO_BASE_ADDRESS + 0x0000 -#define GPNCORE_PAD_BASE IO_BASE_ADDRESS + 0x1000 -#define GPSSUS_PAD_BASE IO_BASE_ADDRESS + 0x2000 +#define GPSCORE_PAD_BASE (IO_BASE_ADDRESS + 0x0000) +#define GPNCORE_PAD_BASE (IO_BASE_ADDRESS + 0x1000) +#define GPSSUS_PAD_BASE (IO_BASE_ADDRESS + 0x2000) /* Pad register offset */ #define PAD_CONF0_REG 0x0 @@ -37,8 +37,8 @@ #define PAD_VAL_REG 0x8 /* Legacy IO register base */ -#define GPSCORE_LEGACY_BASE GPIO_BASE_ADDRESS + 0x00 -#define GPSSUS_LEGACY_BASE GPIO_BASE_ADDRESS + 0x80 +#define GPSCORE_LEGACY_BASE (GPIO_BASE_ADDRESS + 0x00) +#define GPSSUS_LEGACY_BASE (GPIO_BASE_ADDRESS + 0x80) /* Some banks have no legacy GPIO interface */ #define GP_LEGACY_BASE_NONE 0xFFFF @@ -71,19 +71,45 @@ #define GPIO_NEDGE_DISABLE 0 #define GPIO_NEDGE_ENABLE 1 -/* PAD_CONF0 settings */ +/* config0[29] - Disable second mask */ +#define PAD_MASK2_DISABLE (1 << 29) + +/* config0[27] - Direct Irq En */ #define PAD_IRQ_EN (1 << 27) + +/* config0[24] - Gd Level */ #define PAD_LEVEL_IRQ (1 << 24) +#define PAD_EDGE_IRQ (0 << 24) + +/* config0[17] - Slow clkgate / glitch filter */ +#define PAD_SLOWGF_ENABLE (1 << 17) + +/* config0[16] - Fast clkgate / glitch filter */ +#define PAD_FASTGF_ENABLE (1 << 16) +/* config0[15] - Hysteresis enable (inverted) */ +#define PAD_HYST_DISABLE (1 << 15) +#define PAD_HYST_ENABLE (0 << 15) + +/* config0[14:13] - Hysteresis control */ +#define PAD_HYST_CTRL_DEFAULT (2 << 13) + +/* config0[11] - Bypass Flop */ +#define PAD_FLOP_BYPASS (1 << 11) +#define PAD_FLOP_ENABLE (0 << 11) + +/* config0[10:9] - Pull str */ #define PAD_PU_2K (0 << 9) #define PAD_PU_10K (1 << 9) #define PAD_PU_20K (2 << 9) #define PAD_PU_40K (3 << 9) +/* config0[8:7] - Pull assign */ #define PAD_PU_DISABLE (0 << 7) #define PAD_PU_UP (1 << 7) #define PAD_PU_DOWN (2 << 7) +/* config0[2:0] - Func. pin mux */ #define PAD_FUNC0 0x0 #define PAD_FUNC1 0x1 #define PAD_FUNC2 0x2 @@ -92,68 +118,101 @@ #define PAD_FUNC5 0x5 #define PAD_FUNC6 0x6 -/* PAD_VAL settings */ -#define PAD_INPUT_ENABLE (1 << 2) -#define PAD_OUTPUT_ENABLE (1 << 1) +/* pad config0 power-on values - We will not often want to change these */ +#define PAD_CONFIG0_DEFAULT (PAD_MASK2_DISABLE | PAD_SLOWGF_ENABLE | \ + PAD_FASTGF_ENABLE | PAD_HYST_DISABLE | \ + PAD_HYST_CTRL_DEFAULT | PAD_FLOP_BYPASS) -/* End marker */ -#define GPIO_LIST_END 0xffffffff +/* pad config1 reg power-on values - Shouldn't need to change this */ +#define PAD_CONFIG1_DEFAULT 0x8000 + +/* pad_val[2] - Iinenb - active low */ +#define PAD_VAL_INPUT_DISABLE (1 << 2) +#define PAD_VAL_INPUT_ENABLE (0 << 2) + +/* pad_val[1] - Ioutenb - active low */ +#define PAD_VAL_OUTPUT_DISABLE (1 << 1) +#define PAD_VAL_OUTPUT_ENABLE (0 << 1) + +/* pad_val reg power-on default varies by pad, and apparently can cause issues + * if not set correctly, even if the pin isn't configured as GPIO. */ +#define PAD_VAL_DEFAULT (PAD_VAL_INPUT_ENABLE | PAD_VAL_OUTPUT_DISABLE) #define GPIO_INPUT_PU_10K \ - { .pad_conf0 = PAD_PU_10K | PAD_PU_UP, \ - .pad_val = PAD_INPUT_ENABLE, \ + { .pad_conf0 = PAD_PU_10K | PAD_PU_UP | PAD_CONFIG0_DEFAULT, \ + .pad_conf1 = PAD_CONFIG1_DEFAULT, \ + .pad_val = PAD_VAL_INPUT_ENABLE, \ .use_sel = GPIO_USE_LEGACY, \ .io_sel = GPIO_DIR_INPUT } #define GPIO_OUT_LOW \ - { .pad_conf0 = PAD_PU_DISABLE, \ - .pad_val = PAD_OUTPUT_ENABLE, \ + { .pad_conf0 = PAD_PU_DISABLE | PAD_CONFIG0_DEFAULT, \ + .pad_conf1 = PAD_CONFIG1_DEFAULT, \ + .pad_val = PAD_VAL_OUTPUT_ENABLE, \ .use_sel = GPIO_USE_LEGACY, \ .io_sel = GPIO_DIR_OUTPUT, \ .gp_lvl = GPIO_LEVEL_LOW } #define GPIO_OUT_HIGH \ - { .pad_conf0 = PAD_PU_DISABLE, \ - .pad_val = PAD_OUTPUT_ENABLE, \ + { .pad_conf0 = PAD_PU_DISABLE | PAD_CONFIG0_DEFAULT, \ + .pad_conf1 = PAD_CONFIG1_DEFAULT, \ + .pad_val = PAD_VAL_OUTPUT_ENABLE, \ .use_sel = GPIO_USE_LEGACY, \ .io_sel = GPIO_DIR_OUTPUT, \ .gp_lvl = GPIO_LEVEL_HIGH } #define GPIO_FUNC0 \ { .use_sel = GPIO_USE_PAD, \ - .pad_conf0 = PAD_FUNC0 } + .pad_conf0 = PAD_FUNC0 | PAD_CONFIG0_DEFAULT, \ + .pad_conf1 = PAD_CONFIG1_DEFAULT, \ + .pad_val = PAD_VAL_DEFAULT } #define GPIO_FUNC1 \ { .use_sel = GPIO_USE_PAD, \ - .pad_conf0 = PAD_FUNC1 } + .pad_conf0 = PAD_FUNC1 | PAD_CONFIG0_DEFAULT, \ + .pad_conf1 = PAD_CONFIG1_DEFAULT, \ + .pad_val = PAD_VAL_DEFAULT } #define GPIO_FUNC2 \ { .use_sel = GPIO_USE_PAD, \ - .pad_conf0 = PAD_FUNC2 } + .pad_conf0 = PAD_FUNC2 | PAD_CONFIG0_DEFAULT, \ + .pad_conf1 = PAD_CONFIG1_DEFAULT, \ + .pad_val = PAD_VAL_DEFAULT } #define GPIO_FUNC3 \ { .use_sel = GPIO_USE_PAD, \ - .pad_conf0 = PAD_FUNC3 } + .pad_conf0 = PAD_FUNC3 | PAD_CONFIG0_DEFAULT, \ + .pad_conf1 = PAD_CONFIG1_DEFAULT, \ + .pad_val = PAD_VAL_DEFAULT } #define GPIO_FUNC4 \ { .use_sel = GPIO_USE_PAD, \ - .pad_conf0 = PAD_FUNC4 } + .pad_conf0 = PAD_FUNC4 | PAD_CONFIG0_DEFAULT, \ + .pad_conf1 = PAD_CONFIG1_DEFAULT, \ + .pad_val = PAD_VAL_DEFAULT } #define GPIO_FUNC5 \ { .use_sel = GPIO_USE_PAD, \ - .pad_conf0 = PAD_FUNC5 } + .pad_conf0 = PAD_FUNC5 | PAD_CONFIG0_DEFAULT, \ + .pad_conf1 = PAD_CONFIG1_DEFAULT, \ + .pad_val = PAD_VAL_DEFAULT } #define GPIO_FUNC6 \ { .use_sel = GPIO_USE_PAD, \ - .pad_conf0 = PAD_FUNC6 } + .pad_conf0 = PAD_FUNC6 | PAD_CONFIG0_DEFAULT, \ + .pad_conf1 = PAD_CONFIG1_DEFAULT, \ + .pad_val = PAD_VAL_DEFAULT } + +/* End marker */ +#define GPIO_LIST_END 0xffffffff #define GPIO_END \ { .pad_conf0 = GPIO_LIST_END } /* Common default GPIO settings */ -#define GPIO_INPUT GPIO_INPUT_PU_10K -#define GPIO_UNUSED GPIO_INPUT_PU_10K -#define GPIO_DEFAULT GPIO_FUNC0 +#define GPIO_INPUT GPIO_INPUT_PU_10K +#define GPIO_UNUSED GPIO_INPUT_PU_10K +#define GPIO_DEFAULT GPIO_FUNC0 struct soc_gpio_map { u32 pad_conf0; |