aboutsummaryrefslogtreecommitdiff
path: root/src/soc/dmp/vortex86ex
diff options
context:
space:
mode:
Diffstat (limited to 'src/soc/dmp/vortex86ex')
-rw-r--r--src/soc/dmp/vortex86ex/ide_sd_sata.c8
-rw-r--r--src/soc/dmp/vortex86ex/raminit.c2
-rw-r--r--src/soc/dmp/vortex86ex/southbridge.c78
3 files changed, 44 insertions, 44 deletions
diff --git a/src/soc/dmp/vortex86ex/ide_sd_sata.c b/src/soc/dmp/vortex86ex/ide_sd_sata.c
index 936505e436..c60018ab49 100644
--- a/src/soc/dmp/vortex86ex/ide_sd_sata.c
+++ b/src/soc/dmp/vortex86ex/ide_sd_sata.c
@@ -80,20 +80,20 @@ static void init_ide_ata_timing(struct device *dev)
u16 ata_timing_pri, ata_timing_sec;
u32 ata_timing_reg32;
/* Primary channel is SD. */
-#if CONFIG_IDE1_ENABLE
+#if IS_ENABLED(CONFIG_IDE1_ENABLE)
ata_timing_pri = 0x8000;
#else
ata_timing_pri = 0x0000; // Disable this channel.
#endif
/* Secondary channel is SATA. */
-#if CONFIG_IDE2_ENABLE
+#if IS_ENABLED(CONFIG_IDE2_ENABLE)
ata_timing_sec = 0xa30f; // This setting value works well.
#else
ata_timing_sec = 0x0000; // Disable this channel.
#endif
ata_timing_reg32 = (ata_timing_sec << 16) | ata_timing_pri;
pci_write_config32(dev, 0x40, ata_timing_reg32);
-#if CONFIG_IDE_NATIVE_MODE
+#if IS_ENABLED(CONFIG_IDE_NATIVE_MODE)
/* Set both IDE channels to native mode. */
u8 prog_if;
prog_if = pci_read_config8(dev, 0x09);
@@ -110,7 +110,7 @@ static void init_ide_ata_timing(struct device *dev)
static void setup_std_ide_compatible(struct device *dev)
{
-#if CONFIG_IDE_STANDARD_COMPATIBLE
+#if IS_ENABLED(CONFIG_IDE_STANDARD_COMPATIBLE)
// Misc Control Register (MCR) Offset 90h
// bit 0 = Vendor ID Access, bit 1 = Device ID Access.
u8 mcr;
diff --git a/src/soc/dmp/vortex86ex/raminit.c b/src/soc/dmp/vortex86ex/raminit.c
index 1ccdb27e7e..0d4b5b56b3 100644
--- a/src/soc/dmp/vortex86ex/raminit.c
+++ b/src/soc/dmp/vortex86ex/raminit.c
@@ -253,7 +253,7 @@ static u8 detect_ddr3_dram_size(void)
static void print_ddr3_memory_setup(void)
{
-#if CONFIG_DEBUG_RAM_SETUP
+#if IS_ENABLED(CONFIG_DEBUG_RAM_SETUP)
printk(BIOS_DEBUG, "DDR3 Timing Reg 0-3:\n");
printk(BIOS_DEBUG, "NB 6e : ");
print_debug_hex16(pci_read_config16(NB, 0x6e));
diff --git a/src/soc/dmp/vortex86ex/southbridge.c b/src/soc/dmp/vortex86ex/southbridge.c
index 05702d1eb6..451aea67c0 100644
--- a/src/soc/dmp/vortex86ex/southbridge.c
+++ b/src/soc/dmp/vortex86ex/southbridge.c
@@ -207,7 +207,7 @@ static void pci_routing_fixup(struct device *dev)
ext_int_routing |= irq_to_int_routing[CAN_IRQ] << CAN_IRQ_SHIFT;
ext_int_routing |= irq_to_int_routing[HDA_IRQ] << HDA_IRQ_SHIFT;
ext_int_routing |= irq_to_int_routing[USBD_IRQ] << USBD_IRQ_SHIFT;
-#if CONFIG_IDE_NATIVE_MODE
+#if IS_ENABLED(CONFIG_IDE_NATIVE_MODE)
/* IDE in native mode, only uses one IRQ. */
ext_int_routing |= irq_to_int_routing[0] << SIDE_IRQ_SHIFT;
ext_int_routing |= irq_to_int_routing[PIDE_IRQ] << PIDE_IRQ_SHIFT;
@@ -250,21 +250,21 @@ static void vortex_sb_init(struct device *dev)
{
u32 lpt_reg = 0;
-#if CONFIG_LPT_ENABLE
+#if IS_ENABLED(CONFIG_LPT_ENABLE)
int ppmod = 0;
-#if CONFIG_LPT_MODE_BPP
+#if IS_ENABLED(CONFIG_LPT_MODE_BPP)
ppmod = 0;
-#elif CONFIG_LPT_MODE_EPP_19_AND_SPP
+#elif IS_ENABLED(CONFIG_LPT_MODE_EPP_19_AND_SPP)
ppmod = 1;
-#elif CONFIG_LPT_MODE_ECP
+#elif IS_ENABLED(CONFIG_LPT_MODE_ECP)
ppmod = 2;
-#elif CONFIG_LPT_MODE_ECP_AND_EPP_19
+#elif IS_ENABLED(CONFIG_LPT_MODE_ECP_AND_EPP_19)
ppmod = 3;
-#elif CONFIG_LPT_MODE_SPP
+#elif IS_ENABLED(CONFIG_LPT_MODE_SPP)
ppmod = 4;
-#elif CONFIG_LPT_MODE_EPP_17_AND_SPP
+#elif IS_ENABLED(CONFIG_LPT_MODE_EPP_17_AND_SPP)
ppmod = 5;
-#elif CONFIG_LPT_MODE_ECP_AND_EPP_17
+#elif IS_ENABLED(CONFIG_LPT_MODE_ECP_AND_EPP_17)
ppmod = 7;
#else
#error CONFIG_LPT_MODE error.
@@ -303,67 +303,67 @@ static void ex_sb_gpio_init(struct device *dev)
* Bit 31-16 : DBA, GPIO direction base address.
* Bit 15-0 : DPBA, GPIO data port base address.
* */
-#if CONFIG_GPIO_P0_ENABLE
+#if IS_ENABLED(CONFIG_GPIO_P0_ENABLE)
SETUP_GPIO_ADDR(0)
#endif
-#if CONFIG_GPIO_P1_ENABLE
+#if IS_ENABLED(CONFIG_GPIO_P1_ENABLE)
SETUP_GPIO_ADDR(1)
#endif
-#if CONFIG_GPIO_P2_ENABLE
+#if IS_ENABLED(CONFIG_GPIO_P2_ENABLE)
SETUP_GPIO_ADDR(2)
#endif
-#if CONFIG_GPIO_P3_ENABLE
+#if IS_ENABLED(CONFIG_GPIO_P3_ENABLE)
SETUP_GPIO_ADDR(3)
#endif
-#if CONFIG_GPIO_P4_ENABLE
+#if IS_ENABLED(CONFIG_GPIO_P4_ENABLE)
SETUP_GPIO_ADDR(4)
#endif
-#if CONFIG_GPIO_P5_ENABLE
+#if IS_ENABLED(CONFIG_GPIO_P5_ENABLE)
SETUP_GPIO_ADDR(5)
#endif
-#if CONFIG_GPIO_P6_ENABLE
+#if IS_ENABLED(CONFIG_GPIO_P6_ENABLE)
SETUP_GPIO_ADDR(6)
#endif
-#if CONFIG_GPIO_P7_ENABLE
+#if IS_ENABLED(CONFIG_GPIO_P7_ENABLE)
SETUP_GPIO_ADDR(7)
#endif
-#if CONFIG_GPIO_P8_ENABLE
+#if IS_ENABLED(CONFIG_GPIO_P8_ENABLE)
SETUP_GPIO_ADDR(8)
#endif
-#if CONFIG_GPIO_P9_ENABLE
+#if IS_ENABLED(CONFIG_GPIO_P9_ENABLE)
SETUP_GPIO_ADDR(9)
#endif
/* Enable GPIO port 0~9. */
outl(gpio_enable_mask, base);
/* Set GPIO port 0-9 initial dir and data. */
-#if CONFIG_GPIO_P0_ENABLE
+#if IS_ENABLED(CONFIG_GPIO_P0_ENABLE)
INIT_GPIO(0)
#endif
-#if CONFIG_GPIO_P1_ENABLE
+#if IS_ENABLED(CONFIG_GPIO_P1_ENABLE)
INIT_GPIO(1)
#endif
-#if CONFIG_GPIO_P2_ENABLE
+#if IS_ENABLED(CONFIG_GPIO_P2_ENABLE)
INIT_GPIO(2)
#endif
-#if CONFIG_GPIO_P3_ENABLE
+#if IS_ENABLED(CONFIG_GPIO_P3_ENABLE)
INIT_GPIO(3)
#endif
-#if CONFIG_GPIO_P4_ENABLE
+#if IS_ENABLED(CONFIG_GPIO_P4_ENABLE)
INIT_GPIO(4)
#endif
-#if CONFIG_GPIO_P5_ENABLE
+#if IS_ENABLED(CONFIG_GPIO_P5_ENABLE)
INIT_GPIO(5)
#endif
-#if CONFIG_GPIO_P6_ENABLE
+#if IS_ENABLED(CONFIG_GPIO_P6_ENABLE)
INIT_GPIO(6)
#endif
-#if CONFIG_GPIO_P7_ENABLE
+#if IS_ENABLED(CONFIG_GPIO_P7_ENABLE)
INIT_GPIO(7)
#endif
-#if CONFIG_GPIO_P8_ENABLE
+#if IS_ENABLED(CONFIG_GPIO_P8_ENABLE)
INIT_GPIO(8)
#endif
-#if CONFIG_GPIO_P9_ENABLE
+#if IS_ENABLED(CONFIG_GPIO_P9_ENABLE)
INIT_GPIO(9)
#endif
/* Disable GPIO Port Config IO Base Address. */
@@ -391,34 +391,34 @@ static void ex_sb_uart_init(struct device *dev)
/* S/B register 61h - 60h : UART Config IO Base Address */
pci_write_config16(dev, SB_REG_UART_CFG_IO_BASE, base | 1);
/* setup UART */
-#if CONFIG_UART1_ENABLE
+#if IS_ENABLED(CONFIG_UART1_ENABLE)
SETUP_UART(1)
#endif
-#if CONFIG_UART2_ENABLE
+#if IS_ENABLED(CONFIG_UART2_ENABLE)
SETUP_UART(2)
#endif
-#if CONFIG_UART3_ENABLE
+#if IS_ENABLED(CONFIG_UART3_ENABLE)
SETUP_UART(3)
#endif
-#if CONFIG_UART4_ENABLE
+#if IS_ENABLED(CONFIG_UART4_ENABLE)
SETUP_UART(4)
#endif
-#if CONFIG_UART5_ENABLE
+#if IS_ENABLED(CONFIG_UART5_ENABLE)
SETUP_UART(5)
#endif
-#if CONFIG_UART6_ENABLE
+#if IS_ENABLED(CONFIG_UART6_ENABLE)
SETUP_UART(6)
#endif
-#if CONFIG_UART7_ENABLE
+#if IS_ENABLED(CONFIG_UART7_ENABLE)
SETUP_UART(7)
#endif
-#if CONFIG_UART8_ENABLE
+#if IS_ENABLED(CONFIG_UART8_ENABLE)
SETUP_UART(8)
#endif
-#if CONFIG_UART9_ENABLE
+#if IS_ENABLED(CONFIG_UART9_ENABLE)
SETUP_UART(9)
#endif
-#if CONFIG_UART10_ENABLE
+#if IS_ENABLED(CONFIG_UART10_ENABLE)
SETUP_UART(10)
#endif
/* Keep UART Config I/O base address */
generated by cgit v1.2.3 (git 2.39.1) at 2024-07-08 15:36:24 +0000