diff options
Diffstat (limited to 'src/northbridge/intel/e7505/raminit.c')
-rw-r--r-- | src/northbridge/intel/e7505/raminit.c | 266 |
1 files changed, 135 insertions, 131 deletions
diff --git a/src/northbridge/intel/e7505/raminit.c b/src/northbridge/intel/e7505/raminit.c index 46c1903975..21ffba22b5 100644 --- a/src/northbridge/intel/e7505/raminit.c +++ b/src/northbridge/intel/e7505/raminit.c @@ -30,7 +30,7 @@ Definitions: #define RAM_DEBUG_MESSAGE(x) print_debug(x) #define RAM_DEBUG_HEX32(x) print_debug_hex32(x) #define RAM_DEBUG_HEX8(x) print_debug_hex8(x) -#define DUMPNORTH() dump_pci_device(PCI_DEV(0, 0, 0)) +#define DUMPNORTH() dump_pci_device(MCHDEV) #else #define RAM_DEBUG_MESSAGE(x) #define RAM_DEBUG_HEX32(x) @@ -41,6 +41,10 @@ Definitions: #define E7501_SDRAM_MODE (SDRAM_BURST_INTERLEAVED | SDRAM_BURST_4) #define SPD_ERROR "Error reading SPD info\n" +#define MCHDEV PCI_DEV(0,0,0) +#define RASDEV PCI_DEV(0,0,1) +#define D060DEV PCI_DEV(0,6,0) + // NOTE: This used to be 0x100000. // That doesn't work on systems where A20M# is asserted, because // attempts to access 0x1000NN end up accessing 0x0000NN. @@ -438,20 +442,20 @@ static const long constant_register_values[] = { /* DDR RECOMP tables */ #if 0 // Slew table for 1x drive? -static const uint32_t maybe_1x_slew_table[] = { +static const uint32_t 1x_slew_table[] = { 0x44332211, 0xc9776655, 0xffffffff, 0xffffffff, 0x22111111, 0x55444332, 0xfffca876, 0xffffffff, }; #endif // Slew table for 2x drive? -static const uint32_t maybe_2x_slew_table[] = { +static const uint32_t slew_2x[] = { 0x00000000, 0x76543210, 0xffffeca8, 0xffffffff, 0x21000000, 0xa8765432, 0xffffffec, 0xffffffff, }; // Pull Up / Pull Down offset table, if analogous to IXP2800? -static const uint32_t maybe_pull_updown_offset_table[] = { +static const uint32_t pull_updown_offset_table[] = { 0xffffffff, 0xffffffff, 0xffffffff, 0xffffffff, 0x88888888, 0x88888888, 0x88888888, 0x88888888, }; @@ -494,17 +498,17 @@ static void ram_handle_d060_1(void) { uint32_t dword; - dword = pci_read_config32(PCI_DEV(0,0,0), MAYBE_MCHTST); + dword = pci_read_config32(MCHDEV, MCHTST); dword |= 0x02; - pci_write_config32(PCI_DEV(0,0,0), MAYBE_MCHTST, dword); + pci_write_config32(MCHDEV, MCHTST, dword); - dword = pci_read_config32(PCI_DEV(0,6,0), 0xf0); + dword = pci_read_config32(D060DEV, 0xf0); dword |= 0x04; - pci_write_config32(PCI_DEV(0,6,0), 0xf0, dword); + pci_write_config32(D060DEV, 0xf0, dword); - dword = pci_read_config32(PCI_DEV(0,0,0), MAYBE_MCHTST); + dword = pci_read_config32(MCHDEV, MCHTST); dword &= ~0x02; - pci_write_config32(PCI_DEV(0,0,0), MAYBE_MCHTST, dword); + pci_write_config32(MCHDEV, MCHTST, dword); } /** @@ -515,19 +519,19 @@ static void ram_handle_d060_2(void) uint32_t dword; uint8_t revision; - revision = pci_read_config8(PCI_DEV(0,0,0), 0x08); + revision = pci_read_config8(MCHDEV, 0x08); if (revision >= 3) { - dword = pci_read_config32(PCI_DEV(0,0,0), MAYBE_MCHTST); + dword = pci_read_config32(MCHDEV, MCHTST); dword |= 0x02; - pci_write_config32(PCI_DEV(0,0,0), MAYBE_MCHTST, dword); + pci_write_config32(MCHDEV, MCHTST, dword); - dword = pci_read_config32(PCI_DEV(0,6,0), 0xf0); + dword = pci_read_config32(D060DEV, 0xf0); dword |= 0x18000000; - pci_write_config32(PCI_DEV(0,6,0), 0xf0, dword); + pci_write_config32(D060DEV, 0xf0, dword); - dword = pci_read_config32(PCI_DEV(0,0,0), MAYBE_MCHTST); + dword = pci_read_config32(MCHDEV, MCHTST); dword &= ~0x02; - pci_write_config32(PCI_DEV(0,0,0), MAYBE_MCHTST, dword); + pci_write_config32(MCHDEV, MCHTST, dword); } } @@ -902,10 +906,10 @@ static void do_ram_command(uint8_t command, uint16_t jedec_mode_bits) uint8_t i; // Configure the RAM command - dram_controller_mode = pci_read_config32(PCI_DEV(0, 0, 0), DRC); + dram_controller_mode = pci_read_config32(MCHDEV, DRC); dram_controller_mode &= 0xFFFFFF8F; dram_controller_mode |= command; - pci_write_config32(PCI_DEV(0, 0, 0), DRC, dram_controller_mode); + pci_write_config32(MCHDEV, DRC, dram_controller_mode); // RAM_COMMAND_NORMAL is an exception. // It affects only the memory controller and does not need to be "sent" to the DIMMs. @@ -935,7 +939,7 @@ static void do_ram_command(uint8_t command, uint16_t jedec_mode_bits) for (i = 0; i < (MAX_NUM_CHANNELS * MAX_DIMM_SOCKETS_PER_CHANNEL); ++i) { - uint8_t dimm_end_64M_multiple = pci_read_config8(PCI_DEV(0, 0, 0), DRB_ROW_0 + i); + uint8_t dimm_end_64M_multiple = pci_read_config8(MCHDEV, DRB_ROW_0 + i); if (dimm_end_64M_multiple > dimm_start_64M_multiple) { dimm_start_address &= 0x3ffffff; @@ -962,7 +966,7 @@ static void set_ram_mode(uint16_t jedec_mode_bits) ASSERT(!(jedec_mode_bits & SDRAM_CAS_MASK)); uint32_t dram_cas_latency = - pci_read_config32(PCI_DEV(0, 0, 0), DRT) & DRT_CAS_MASK; + pci_read_config32(MCHDEV, DRT) & DRT_CAS_MASK; switch (dram_cas_latency) { case DRT_CAS_2_5: @@ -1024,7 +1028,7 @@ static uint8_t configure_dimm_row_boundaries(struct dimm_size dimm_log2_num_bits total_dram_64M_multiple += (1 << (dimm_log2_num_bits.side1 - 29)); // Configure the boundary address for the row on side 1 - pci_write_config8(PCI_DEV(0, 0, 0), DRB_ROW_0 + (dimm_index << 1), + pci_write_config8(MCHDEV, DRB_ROW_0 + (dimm_index << 1), total_dram_64M_multiple); // If the DIMMs are double-sided, add the capacity of side 2 this DIMM pair @@ -1034,16 +1038,16 @@ static uint8_t configure_dimm_row_boundaries(struct dimm_size dimm_log2_num_bits (1 << (dimm_log2_num_bits.side2 - 29)); // Configure the boundary address for the row (if any) on side 2 - pci_write_config8(PCI_DEV(0, 0, 0), DRB_ROW_1 + (dimm_index << 1), + pci_write_config8(MCHDEV, DRB_ROW_1 + (dimm_index << 1), total_dram_64M_multiple); // Update boundaries for rows subsequent to these. // These settings will be overridden by a subsequent call if a populated physical slot exists for (i = dimm_index + 1; i < MAX_DIMM_SOCKETS_PER_CHANNEL; i++) { - pci_write_config8(PCI_DEV(0, 0, 0), DRB_ROW_0 + (i << 1), + pci_write_config8(MCHDEV, DRB_ROW_0 + (i << 1), total_dram_64M_multiple); - pci_write_config8(PCI_DEV(0, 0, 0), DRB_ROW_1 + (i << 1), + pci_write_config8(MCHDEV, DRB_ROW_1 + (i << 1), total_dram_64M_multiple); } @@ -1068,8 +1072,8 @@ static void configure_e7501_ram_addresses(const struct mem_controller // Configure the E7501's DRAM row boundaries // Start by zeroing out the temporary initial configuration - pci_write_config32(PCI_DEV(0, 0, 0), DRB_ROW_0, 0); - pci_write_config32(PCI_DEV(0, 0, 0), DRB_ROW_4, 0); + pci_write_config32(MCHDEV, DRB_ROW_0, 0); + pci_write_config32(MCHDEV, DRB_ROW_4, 0); for (i = 0; i < MAX_DIMM_SOCKETS_PER_CHANNEL; i++) { @@ -1127,7 +1131,7 @@ static void configure_e7501_ram_addresses(const struct mem_controller uint16_t top_of_low_memory = total_dram_128M_multiple << 11; - pci_write_config16(PCI_DEV(0, 0, 0), TOLM, + pci_write_config16(MCHDEV, TOLM, top_of_low_memory); } else { @@ -1140,7 +1144,7 @@ static void configure_e7501_ram_addresses(const struct mem_controller // Put TOLM at 3 GB - pci_write_config16(PCI_DEV(0, 0, 0), TOLM, 0xc000); + pci_write_config16(MCHDEV, TOLM, 0xc000); // Define a remap window to make the RAM that would appear from 3 GB - 4 GB // visible just beyond 4 GB or the end of physical memory, whichever is larger @@ -1154,9 +1158,9 @@ static void configure_e7501_ram_addresses(const struct mem_controller 0x40 + (total_dram_64M_multiple - 0x30) - 1; } - pci_write_config16(PCI_DEV(0, 0, 0), REMAPBASE, + pci_write_config16(MCHDEV, REMAPBASE, remap_base); - pci_write_config16(PCI_DEV(0, 0, 0), REMAPLIMIT, + pci_write_config16(MCHDEV, REMAPLIMIT, remap_limit); } } @@ -1170,31 +1174,31 @@ static void initialize_ecc(void) uint32_t dram_controller_mode; /* Test to see if ECC support is enabled */ - dram_controller_mode = pci_read_config32(PCI_DEV(0, 0, 0), DRC); + dram_controller_mode = pci_read_config32(MCHDEV, DRC); dram_controller_mode >>= 20; dram_controller_mode &= 3; if (dram_controller_mode == 2) { uint8_t byte; RAM_DEBUG_MESSAGE("Initializing ECC state...\n"); - pci_write_config8(PCI_DEV(0, 0, 0), MCHCFGNS, 0x01); + pci_write_config8(MCHDEV, MCHCFGNS, 0x01); // Wait for scrub cycle to complete do { byte = - pci_read_config8(PCI_DEV(0, 0, 0), MCHCFGNS); + pci_read_config8(MCHDEV, MCHCFGNS); } while ((byte & 0x08) == 0); - pci_write_config8(PCI_DEV(0, 0, 0), MCHCFGNS, (byte & 0xfc) | 0x04); + pci_write_config8(MCHDEV, MCHCFGNS, (byte & 0xfc) | 0x04); RAM_DEBUG_MESSAGE("ECC state initialized.\n"); /* Clear the ECC error bits */ - pci_write_config8(PCI_DEV(0, 0, 1), DRAM_FERR, 0x03); - pci_write_config8(PCI_DEV(0, 0, 1), DRAM_NERR, 0x03); + pci_write_config8(RASDEV, DRAM_FERR, 0x03); + pci_write_config8(RASDEV, DRAM_NERR, 0x03); // Clear DRAM Interface error bits (write-one-clear) - pci_write_config32(PCI_DEV(0, 0, 1), FERR_GLOBAL, 1 << 18); - pci_write_config32(PCI_DEV(0, 0, 1), NERR_GLOBAL, 1 << 18); + pci_write_config32(RASDEV, FERR_GLOBAL, 1 << 18); + pci_write_config32(RASDEV, NERR_GLOBAL, 1 << 18); } } @@ -1218,7 +1222,7 @@ static void configure_e7501_dram_timing(const struct mem_controller *ctrl, uint8_t slowest_ras_cas_delay = 0; uint8_t slowest_active_to_precharge_delay = 0; uint32_t current_cas_latency = - pci_read_config32(PCI_DEV(0, 0, 0), DRT) & DRT_CAS_MASK; + pci_read_config32(MCHDEV, DRT) & DRT_CAS_MASK; // CAS# latency must be programmed beforehand ASSERT((current_cas_latency == DRT_CAS_2_0) @@ -1267,7 +1271,7 @@ static void configure_e7501_dram_timing(const struct mem_controller *ctrl, // At 133 MHz, 1 clock == 7.52 ns /* Read the initial state */ - dram_timing = pci_read_config32(PCI_DEV(0, 0, 0), DRT); + dram_timing = pci_read_config32(MCHDEV, DRT); /* Trp */ @@ -1326,7 +1330,7 @@ static void configure_e7501_dram_timing(const struct mem_controller *ctrl, if (current_cas_latency == DRT_CAS_2_0) dram_timing |= (1 << 28); // 4 clocks - pci_write_config32(PCI_DEV(0, 0, 0), DRT, dram_timing); + pci_write_config32(MCHDEV, DRT, dram_timing); return; @@ -1348,7 +1352,7 @@ static void configure_e7501_cas_latency(const struct mem_controller *ctrl, int i; int value; uint32_t dram_timing; - uint16_t maybe_dram_read_timing; + uint16_t dram_read_timing; uint32_t dword; // CAS# latency bitmasks in SPD_ACCEPTABLE_CAS_LATENCIES format @@ -1430,20 +1434,20 @@ static void configure_e7501_cas_latency(const struct mem_controller *ctrl, * cas latency I can use. */ - dram_timing = pci_read_config32(PCI_DEV(0, 0, 0), DRT); + dram_timing = pci_read_config32(MCHDEV, DRT); dram_timing &= ~(DRT_CAS_MASK); - maybe_dram_read_timing = - pci_read_config16(PCI_DEV(0, 0, 0), MAYBE_DRDCTL); - maybe_dram_read_timing &= 0xF000; + dram_read_timing = + pci_read_config16(MCHDEV, DRDCTL); + dram_read_timing &= 0xF000; if (system_compatible_cas_latencies & SPD_CAS_LATENCY_2_0) { dram_timing |= DRT_CAS_2_0; - maybe_dram_read_timing |= 0x0222; + dram_read_timing |= 0x0222; } else if (system_compatible_cas_latencies & SPD_CAS_LATENCY_2_5) { uint32_t dram_row_attributes = - pci_read_config32(PCI_DEV(0, 0, 0), DRA); + pci_read_config32(MCHDEV, DRA); dram_timing |= DRT_CAS_2_5; @@ -1456,32 +1460,32 @@ static void configure_e7501_cas_latency(const struct mem_controller *ctrl, && (dram_row_attributes & 0xff000000)) { // All slots populated - maybe_dram_read_timing |= 0x0882; + dram_read_timing |= 0x0882; } else { // Some unpopulated slots - maybe_dram_read_timing |= 0x0662; + dram_read_timing |= 0x0662; } } else die("No CAS# latencies compatible with all DIMMs!!\n"); - pci_write_config32(PCI_DEV(0, 0, 0), DRT, dram_timing); + pci_write_config32(MCHDEV, DRT, dram_timing); /* set master DLL reset */ - dword = pci_read_config32(PCI_DEV(0, 0, 0), 0x88); + dword = pci_read_config32(MCHDEV, 0x88); dword |= (1 << 26); - pci_write_config32(PCI_DEV(0, 0, 0), 0x88, dword); + pci_write_config32(MCHDEV, 0x88, dword); /* patch try register 88 is undocumented tnz */ dword &= 0x0ca17fff; dword |= 0xd14a5000; - pci_write_config32(PCI_DEV(0, 0, 0), 0x88, dword); + pci_write_config32(MCHDEV, 0x88, dword); - pci_write_config16(PCI_DEV(0, 0, 0), MAYBE_DRDCTL, - maybe_dram_read_timing); + pci_write_config16(MCHDEV, DRDCTL, + dram_read_timing); /* clear master DLL reset */ - dword = pci_read_config32(PCI_DEV(0, 0, 0), 0x88); + dword = pci_read_config32(MCHDEV, 0x88); dword &= ~(1 << 26); - pci_write_config32(PCI_DEV(0, 0, 0), 0x88, dword); + pci_write_config32(MCHDEV, 0x88, dword); return; @@ -1506,7 +1510,7 @@ static void configure_e7501_dram_controller_mode(const struct // Initial settings uint32_t controller_mode = - pci_read_config32(PCI_DEV(0, 0, 0), DRC); + pci_read_config32(MCHDEV, DRC); uint32_t system_refresh_mode = (controller_mode >> 8) & 7; // Code below assumes that most aggressive settings are in @@ -1592,7 +1596,7 @@ static void configure_e7501_dram_controller_mode(const struct controller_mode |= (system_refresh_mode << 8); // Configure the E7501 - pci_write_config32(PCI_DEV(0, 0, 0), DRC, controller_mode); + pci_write_config32(MCHDEV, DRC, controller_mode); } /** @@ -1645,7 +1649,7 @@ static void configure_e7501_row_attributes(const struct mem_controller } /* Write the new row attributes register */ - pci_write_config32(PCI_DEV(0, 0, 0), DRA, row_attributes); + pci_write_config32(MCHDEV, DRA, row_attributes); } /* @@ -1657,9 +1661,9 @@ static void configure_e7501_row_attributes(const struct mem_controller static void enable_e7501_clocks(uint8_t dimm_mask) { int i; - uint8_t clock_disable = pci_read_config8(PCI_DEV(0, 0, 0), CKDIS); + uint8_t clock_disable = pci_read_config8(MCHDEV, CKDIS); - pci_write_config8(PCI_DEV(0,0,0), 0x8e, 0xb0); + pci_write_config8(MCHDEV, 0x8e, 0xb0); for (i = 0; i < MAX_DIMM_SOCKETS_PER_CHANNEL; i++) { @@ -1671,7 +1675,7 @@ static void enable_e7501_clocks(uint8_t dimm_mask) clock_disable |= socket_mask; // DIMM absent, disable clock } - pci_write_config8(PCI_DEV(0, 0, 0), CKDIS, clock_disable); + pci_write_config8(MCHDEV, CKDIS, clock_disable); } /* DIMM-dedependent configuration functions */ @@ -1682,13 +1686,13 @@ static void enable_e7501_clocks(uint8_t dimm_mask) static void RAM_RESET_DDR_PTR(void) { uint8_t byte; - byte = pci_read_config8(PCI_DEV(0, 0, 0), 0x88); + byte = pci_read_config8(MCHDEV, 0x88); byte |= (1 << 4); - pci_write_config8(PCI_DEV(0, 0, 0), 0x88, byte); + pci_write_config8(MCHDEV, 0x88, byte); - byte = pci_read_config8(PCI_DEV(0, 0, 0), 0x88); + byte = pci_read_config8(MCHDEV, 0x88); byte &= ~(1 << 4); - pci_write_config8(PCI_DEV(0, 0, 0), 0x88, byte); + pci_write_config8(MCHDEV, 0x88, byte); } /** @@ -1723,11 +1727,11 @@ static void ram_set_d0f0_regs(void) ASSERT((bits_to_mask & bits_to_set) == 0); register_value = - pci_read_config32(PCI_DEV(0, 0, 0), register_offset); + pci_read_config32(MCHDEV, register_offset); register_value &= bits_to_mask; register_value |= bits_to_set; - pci_write_config32(PCI_DEV(0, 0, 0), register_offset, + pci_write_config32(MCHDEV, register_offset, register_value); } } @@ -1761,87 +1765,87 @@ static void write_8dwords(const uint32_t *src_addr, uint32_t dst_addr) static void ram_set_rcomp_regs(void) { uint32_t dword; - uint8_t maybe_strength_control, revision; + uint8_t strength_control, revision; RAM_DEBUG_MESSAGE("Setting RCOMP registers.\n"); /*enable access to the rcomp bar */ - dword = pci_read_config32(PCI_DEV(0, 0, 0), MAYBE_MCHTST); + dword = pci_read_config32(MCHDEV, MCHTST); dword |= (1 << 22); - pci_write_config32(PCI_DEV(0, 0, 0), MAYBE_MCHTST, dword); + pci_write_config32(MCHDEV, MCHTST, dword); // Set the RCOMP MMIO base address - pci_write_config32(PCI_DEV(0, 0, 0), MAYBE_SMRBASE, RCOMP_MMIO); + pci_write_config32(MCHDEV, SMRBASE, RCOMP_MMIO); // Block RCOMP updates while we configure the registers - dword = read32(RCOMP_MMIO + MAYBE_SMRCTL); + dword = read32(RCOMP_MMIO + SMRCTL); dword |= (1 << 9); - write32(RCOMP_MMIO + MAYBE_SMRCTL, dword); + write32(RCOMP_MMIO + SMRCTL, dword); /* Begin to write the RCOMP registers */ write8(RCOMP_MMIO + 0x2c, 0x0); // Set CMD and DQ/DQS strength to 2x (?) - maybe_strength_control = read8(RCOMP_MMIO + MAYBE_DQCMDSTR) & 0x88; - maybe_strength_control |= 0x40; - write8(RCOMP_MMIO + MAYBE_DQCMDSTR, maybe_strength_control); - write_8dwords(maybe_2x_slew_table, RCOMP_MMIO + 0x80); + strength_control = read8(RCOMP_MMIO + DQCMDSTR) & 0x88; + strength_control |= 0x40; + write8(RCOMP_MMIO + DQCMDSTR, strength_control); + write_8dwords(slew_2x, RCOMP_MMIO + 0x80); write16(RCOMP_MMIO + 0x42, 0); // Set CMD and DQ/DQS strength to 2x (?) - maybe_strength_control = read8(RCOMP_MMIO + MAYBE_DQCMDSTR) & 0xF8; - maybe_strength_control |= 0x04; - write8(RCOMP_MMIO + MAYBE_DQCMDSTR, maybe_strength_control); - write_8dwords(maybe_2x_slew_table, RCOMP_MMIO + 0x60); + strength_control = read8(RCOMP_MMIO + DQCMDSTR) & 0xF8; + strength_control |= 0x04; + write8(RCOMP_MMIO + DQCMDSTR, strength_control); + write_8dwords(slew_2x, RCOMP_MMIO + 0x60); write16(RCOMP_MMIO + 0x40, 0); // Set RCVEnOut# strength to 2x (?) - maybe_strength_control = read8(RCOMP_MMIO + MAYBE_RCVENSTR) & 0xF8; - maybe_strength_control |= 0x04; - write8(RCOMP_MMIO + MAYBE_RCVENSTR, maybe_strength_control); - write_8dwords(maybe_2x_slew_table, RCOMP_MMIO + 0x1c0); + strength_control = read8(RCOMP_MMIO + RCVENSTR) & 0xF8; + strength_control |= 0x04; + write8(RCOMP_MMIO + RCVENSTR, strength_control); + write_8dwords(slew_2x, RCOMP_MMIO + 0x1c0); write16(RCOMP_MMIO + 0x50, 0); // Set CS# strength for x4 SDRAM to 2x (?) - maybe_strength_control = read8(RCOMP_MMIO + MAYBE_CSBSTR) & 0x88; - maybe_strength_control |= 0x04; - write8(RCOMP_MMIO + MAYBE_CSBSTR, maybe_strength_control); - write_8dwords(maybe_2x_slew_table, RCOMP_MMIO + 0x140); + strength_control = read8(RCOMP_MMIO + CSBSTR) & 0x88; + strength_control |= 0x04; + write8(RCOMP_MMIO + CSBSTR, strength_control); + write_8dwords(slew_2x, RCOMP_MMIO + 0x140); write16(RCOMP_MMIO + 0x48, 0); // Set CS# strength for x4 SDRAM to 2x (?) - maybe_strength_control = read8(RCOMP_MMIO + MAYBE_CSBSTR) & 0x8F; - maybe_strength_control |= 0x40; - write8(RCOMP_MMIO + MAYBE_CSBSTR, maybe_strength_control); - write_8dwords(maybe_2x_slew_table, RCOMP_MMIO + 0x160); + strength_control = read8(RCOMP_MMIO + CSBSTR) & 0x8F; + strength_control |= 0x40; + write8(RCOMP_MMIO + CSBSTR, strength_control); + write_8dwords(slew_2x, RCOMP_MMIO + 0x160); write16(RCOMP_MMIO + 0x4a, 0); // Set CKE strength for x4 SDRAM to 2x (?) - maybe_strength_control = read8(RCOMP_MMIO + MAYBE_CKESTR) & 0x88; - maybe_strength_control |= 0x04; - write8(RCOMP_MMIO + MAYBE_CKESTR, maybe_strength_control); - write_8dwords(maybe_2x_slew_table, RCOMP_MMIO + 0xa0); + strength_control = read8(RCOMP_MMIO + CKESTR) & 0x88; + strength_control |= 0x04; + write8(RCOMP_MMIO + CKESTR, strength_control); + write_8dwords(slew_2x, RCOMP_MMIO + 0xa0); write16(RCOMP_MMIO + 0x44, 0); // Set CKE strength for x4 SDRAM to 2x (?) - maybe_strength_control = read8(RCOMP_MMIO + MAYBE_CKESTR) & 0x8F; - maybe_strength_control |= 0x40; - write8(RCOMP_MMIO + MAYBE_CKESTR, maybe_strength_control); - write_8dwords(maybe_2x_slew_table, RCOMP_MMIO + 0xc0); + strength_control = read8(RCOMP_MMIO + CKESTR) & 0x8F; + strength_control |= 0x40; + write8(RCOMP_MMIO + CKESTR, strength_control); + write_8dwords(slew_2x, RCOMP_MMIO + 0xc0); write16(RCOMP_MMIO + 0x46, 0); // Set CK strength for x4 SDRAM to 1x (?) - maybe_strength_control = read8(RCOMP_MMIO + MAYBE_CKSTR) & 0x88; - maybe_strength_control |= 0x01; - write8(RCOMP_MMIO + MAYBE_CKSTR, maybe_strength_control); - write_8dwords(maybe_pull_updown_offset_table, RCOMP_MMIO + 0x180); + strength_control = read8(RCOMP_MMIO + CKSTR) & 0x88; + strength_control |= 0x01; + write8(RCOMP_MMIO + CKSTR, strength_control); + write_8dwords(pull_updown_offset_table, RCOMP_MMIO + 0x180); write16(RCOMP_MMIO + 0x4c, 0); // Set CK strength for x4 SDRAM to 1x (?) - maybe_strength_control = read8(RCOMP_MMIO + MAYBE_CKSTR) & 0x8F; - maybe_strength_control |= 0x10; - write8(RCOMP_MMIO + MAYBE_CKSTR, maybe_strength_control); - write_8dwords(maybe_pull_updown_offset_table, RCOMP_MMIO + 0x1a0); + strength_control = read8(RCOMP_MMIO + CKSTR) & 0x8F; + strength_control |= 0x10; + write8(RCOMP_MMIO + CKSTR, strength_control); + write_8dwords(pull_updown_offset_table, RCOMP_MMIO + 0x1a0); write16(RCOMP_MMIO + 0x4e, 0); @@ -1855,33 +1859,33 @@ static void ram_set_rcomp_regs(void) ram_handle_d060_1(); - dword = pci_read_config32(PCI_DEV(0,0,0), MAYBE_MCHTST); + dword = pci_read_config32(MCHDEV, MCHTST); dword &= 0x3fffffff; - pci_write_config32(PCI_DEV(0,0,0), MAYBE_MCHTST, dword); + pci_write_config32(MCHDEV, MCHTST, dword); - revision = pci_read_config8(PCI_DEV(0,0,0), 0x08); + revision = pci_read_config8(MCHDEV, 0x08); if (revision >= 3) { - dword = read32(RCOMP_MMIO + MAYBE_SMRCTL); + dword = read32(RCOMP_MMIO + SMRCTL); dword &= ~0x100; - write32(RCOMP_MMIO + MAYBE_SMRCTL, dword); - dword = read32(RCOMP_MMIO + MAYBE_SMRCTL); + write32(RCOMP_MMIO + SMRCTL, dword); + dword = read32(RCOMP_MMIO + SMRCTL); dword |= 0x500; - write32(RCOMP_MMIO + MAYBE_SMRCTL, dword); + write32(RCOMP_MMIO + SMRCTL, dword); } - dword = read32(RCOMP_MMIO + MAYBE_SMRCTL); + dword = read32(RCOMP_MMIO + SMRCTL); dword &= ~0x203; dword |= 0x401; - write32(RCOMP_MMIO + MAYBE_SMRCTL, dword); + write32(RCOMP_MMIO + SMRCTL, dword); /* Wait 40 usec */ SLOW_DOWN_IO; // Clear the RCOMP MMIO base address - pci_write_config32(PCI_DEV(0, 0, 0), MAYBE_SMRBASE, 0); + pci_write_config32(MCHDEV, SMRBASE, 0); /*disable access to the rcomp bar */ - dword = pci_read_config32(PCI_DEV(0, 0, 0), MAYBE_MCHTST); + dword = pci_read_config32(MCHDEV, MCHTST); dword &= ~(1 << 22); - pci_write_config32(PCI_DEV(0, 0, 0), MAYBE_MCHTST, dword); + pci_write_config32(MCHDEV, MCHTST, dword); } @@ -1901,7 +1905,7 @@ Public interface: static void sdram_enable(int controllers, const struct mem_controller *ctrl) { - uint8_t dimm_mask = pci_read_config16(PCI_DEV(0, 0, 0), SKPD); + uint8_t dimm_mask = pci_read_config16(MCHDEV, SKPD); uint32_t dram_controller_mode; if (dimm_mask == 0) @@ -1988,15 +1992,15 @@ static void sdram_enable(int controllers, configure_e7501_ram_addresses(ctrl, dimm_mask); /* Finally enable refresh */ - dram_controller_mode = pci_read_config32(PCI_DEV(0, 0, 0), DRC); + dram_controller_mode = pci_read_config32(MCHDEV, DRC); dram_controller_mode |= (1 << 29); - pci_write_config32(PCI_DEV(0, 0, 0), DRC, dram_controller_mode); + pci_write_config32(MCHDEV, DRC, dram_controller_mode); EXTRA_DELAY; initialize_ecc(); - dram_controller_mode = pci_read_config32(PCI_DEV(0, 0, 0), DRC); /* FCS_EN */ + dram_controller_mode = pci_read_config32(MCHDEV, DRC); /* FCS_EN */ dram_controller_mode |= (1 << 17); // NOTE: undocumented reserved bit - pci_write_config32(PCI_DEV(0, 0, 0), DRC, dram_controller_mode); + pci_write_config32(MCHDEV, DRC, dram_controller_mode); RAM_DEBUG_MESSAGE("Northbridge following SDRAM init:\n"); DUMPNORTH(); @@ -2045,7 +2049,7 @@ static void sdram_set_spd_registers(const struct mem_controller *ctrl) * configure_e7501_ram_addresses() without having to regenerate the bitmask * of usable DIMMs. */ - pci_write_config16(PCI_DEV(0, 0, 0), SKPD, dimm_mask); + pci_write_config16(MCHDEV, SKPD, dimm_mask); } /** |