diff options
Diffstat (limited to 'src/mainboard')
25 files changed, 1897 insertions, 0 deletions
diff --git a/src/mainboard/dell/Kconfig b/src/mainboard/dell/Kconfig new file mode 100644 index 0000000000..298c62b52b --- /dev/null +++ b/src/mainboard/dell/Kconfig @@ -0,0 +1,16 @@ +if VENDOR_DELL + +choice + prompt "Mainboard model" + +source "src/mainboard/dell/*/Kconfig.name" + +endchoice + +source "src/mainboard/dell/*/Kconfig" + +config MAINBOARD_VENDOR + string + default "Dell Inc." + +endif # VENDOR_DELL diff --git a/src/mainboard/dell/Kconfig.name b/src/mainboard/dell/Kconfig.name new file mode 100644 index 0000000000..3d2fefd11d --- /dev/null +++ b/src/mainboard/dell/Kconfig.name @@ -0,0 +1,2 @@ +config VENDOR_DELL + bool "Dell Inc." diff --git a/src/mainboard/dell/optiplex_9010/Kconfig b/src/mainboard/dell/optiplex_9010/Kconfig new file mode 100644 index 0000000000..6a3feb3751 --- /dev/null +++ b/src/mainboard/dell/optiplex_9010/Kconfig @@ -0,0 +1,69 @@ +if BOARD_DELL_OPTIPLEX_9010 + +config BOARD_SPECIFIC_OPTIONS + def_bool y + select BOARD_ROMSIZE_KB_12288 + select HAVE_ACPI_RESUME + select HAVE_ACPI_TABLES + select INTEL_INT15 + select NORTHBRIDGE_INTEL_SANDYBRIDGE + select SERIRQ_CONTINUOUS_MODE + select SOUTHBRIDGE_INTEL_C216 + select USE_NATIVE_RAMINIT + select MAINBOARD_HAS_LPC_TPM + select MAINBOARD_HAS_TPM1 + select MAINBOARD_USES_IFD_GBE_REGION + select SUPERIO_SMSC_SCH5545 + select MAINBOARD_HAS_LIBGFXINIT + select INTEL_GMA_HAVE_VBT + select HAVE_OPTION_TABLE + select HAVE_CMOS_DEFAULT + select PCIEXP_L1_SUB_STATE + +config MAINBOARD_DIR + string + default dell/optiplex_9010 + +config MAINBOARD_PART_NUMBER + string + default "OptiPlex 9010" + +config VGA_BIOS_FILE + string + default "pci8086,0162.rom" + +config VGA_BIOS_ID + string + default "8086,0162" + +config DRAM_RESET_GATE_GPIO + int + default 60 + +config MAX_CPUS + int + default 8 + +config USBDEBUG_HCD_INDEX + int + default 2 + +config CBFS_SIZE + hex + default 0x600000 + +config INCLUDE_SMSC_SCH5545_EC_FW + bool "Include SMSC SCH5545 EC firmware binary" + default n + help + This option allows to add the SMSC SCH5545 Environmental Controller + firmware binary. The firmware must be loaded after each power failure + in order to properly initialize the fan control, because EC loses its + configuration when power is cut off. Otherwise the fans will keep + running at full speed after power failure. + +config SMSC_SCH5545_EC_FW_FILE + string "File path to the SMSC SCH5545 EC firmware binary" + depends on INCLUDE_SMSC_SCH5545_EC_FW + +endif diff --git a/src/mainboard/dell/optiplex_9010/Kconfig.name b/src/mainboard/dell/optiplex_9010/Kconfig.name new file mode 100644 index 0000000000..96707c2890 --- /dev/null +++ b/src/mainboard/dell/optiplex_9010/Kconfig.name @@ -0,0 +1,2 @@ +config BOARD_DELL_OPTIPLEX_9010 + bool "OptiPlex 9010 SFF" diff --git a/src/mainboard/dell/optiplex_9010/Makefile.inc b/src/mainboard/dell/optiplex_9010/Makefile.inc new file mode 100644 index 0000000000..7a8a68423a --- /dev/null +++ b/src/mainboard/dell/optiplex_9010/Makefile.inc @@ -0,0 +1,22 @@ +# SPDX-License-Identifier: GPL-2.0-only + +smm-y += smihandler.c + +bootblock-y += gpio.c +romstage-y += gpio.c + +bootblock-y += early_init.c +romstage-y += early_init.c + +bootblock-y += sch5545_ec_early.c + +romstage-y += sch5545_ec.c + +ramstage-y += sch5545_ec.c +ramstage-$(CONFIG_MAINBOARD_USE_LIBGFXINIT) += gma-mainboard.ads + +ifeq ($(CONFIG_INCLUDE_SMSC_SCH5545_EC_FW),y) +cbfs-files-y += sch5545_ecfw.bin +sch5545_ecfw.bin-file := $(call strip_quotes,$(CONFIG_SMSC_SCH5545_EC_FW_FILE)) +sch5545_ecfw.bin-type := raw +endif diff --git a/src/mainboard/dell/optiplex_9010/acpi/ec.asl b/src/mainboard/dell/optiplex_9010/acpi/ec.asl new file mode 100644 index 0000000000..e69de29bb2 --- /dev/null +++ b/src/mainboard/dell/optiplex_9010/acpi/ec.asl diff --git a/src/mainboard/dell/optiplex_9010/acpi/platform.asl b/src/mainboard/dell/optiplex_9010/acpi/platform.asl new file mode 100644 index 0000000000..f890b5af54 --- /dev/null +++ b/src/mainboard/dell/optiplex_9010/acpi/platform.asl @@ -0,0 +1,54 @@ +/* SPDX-License-Identifier: GPL-2.0-only */ + +Method(_WAK,1) +{ + \_SB.PCI0.LPCB.SIO1.SIOW (Arg0) + + Return(Package(){0,0}) +} + +Method(_PTS,1) +{ + \_SB.PCI0.LPCB.SIO1.SIOS (Arg0) +} + +Scope (\_SB) +{ + Device (PWRB) + { + Name (_HID, EisaId ("PNP0C0C")) + Name (_UID, 0xAA) + Name (_STA, 0x0B) + + Name (_PRW, Package() { 8, 3}) + } +} + +Scope (\_GPE) +{ + Method (_L08, 0, NotSerialized) + { + \_SB.PCI0.LPCB.SIO1.SIOH () + Notify (\_SB.PWRB, 0x02) + } + + Method (_L0D, 0, NotSerialized) + { + Notify (\_SB.PCI0.EHC1, 0x02) + Notify (\_SB.PCI0.EHC2, 0x02) + Notify (\_SB.PCI0.GLAN, 0x02) + } + + Method (_L09, 0, NotSerialized) + { + Notify (\_SB.PCI0.RP01, 0x02) + Notify (\_SB.PCI0.RP02, 0x02) + Notify (\_SB.PCI0.RP03, 0x02) + Notify (\_SB.PCI0.RP04, 0x02) + Notify (\_SB.PCI0.RP05, 0x02) + Notify (\_SB.PCI0.RP06, 0x02) + Notify (\_SB.PCI0.RP07, 0x02) + Notify (\_SB.PCI0.RP08, 0x02) + Notify (\_SB.PCI0.PEGP, 0x02) + } +} diff --git a/src/mainboard/dell/optiplex_9010/acpi/superio.asl b/src/mainboard/dell/optiplex_9010/acpi/superio.asl new file mode 100644 index 0000000000..fa1dfcf726 --- /dev/null +++ b/src/mainboard/dell/optiplex_9010/acpi/superio.asl @@ -0,0 +1,13 @@ +/* SPDX-License-Identifier: GPL-2.0-only */ + +#undef SUPERIO_DEV +#undef SUPERIO_PNP_BASE +#define SUPERIO_DEV SIO1 +#define SUPERIO_PNP_BASE 0x2e + +#define SCH5545_RUNTIME_BASE 0xa00 +#define SCH5545_EMI_BASE 0xa40 +#define SCH5545_SHOW_UARTA +#define SCH5545_SHOW_KBC + +#include <superio/smsc/sch5545/acpi/superio.asl> diff --git a/src/mainboard/dell/optiplex_9010/acpi_tables.c b/src/mainboard/dell/optiplex_9010/acpi_tables.c new file mode 100644 index 0000000000..33feed2a98 --- /dev/null +++ b/src/mainboard/dell/optiplex_9010/acpi_tables.c @@ -0,0 +1,9 @@ +/* SPDX-License-Identifier: GPL-2.0-only */ + +#include <southbridge/intel/bd82x6x/nvs.h> + +void acpi_create_gnvs(global_nvs_t *gnvs) +{ + gnvs->tcrt = 100; + gnvs->tpsv = 90; +} diff --git a/src/mainboard/dell/optiplex_9010/board_info.txt b/src/mainboard/dell/optiplex_9010/board_info.txt new file mode 100644 index 0000000000..f49f3ba416 --- /dev/null +++ b/src/mainboard/dell/optiplex_9010/board_info.txt @@ -0,0 +1,6 @@ +Category: desktop +ROM protocol: SPI +ROM package: SOIC-8, SOIC-16 +ROM socketed: n +Flashrom support: y +Release year: 2012 diff --git a/src/mainboard/dell/optiplex_9010/cmos.default b/src/mainboard/dell/optiplex_9010/cmos.default new file mode 100644 index 0000000000..ccc7e64625 --- /dev/null +++ b/src/mainboard/dell/optiplex_9010/cmos.default @@ -0,0 +1,7 @@ +boot_option=Fallback +debug_level=Debug +power_on_after_fail=Disable +nmi=Enable +sata_mode=AHCI +gfx_uma_size=128M +fan_full_speed=Disable diff --git a/src/mainboard/dell/optiplex_9010/cmos.layout b/src/mainboard/dell/optiplex_9010/cmos.layout new file mode 100644 index 0000000000..dcf9639d3f --- /dev/null +++ b/src/mainboard/dell/optiplex_9010/cmos.layout @@ -0,0 +1,95 @@ +## SPDX-License-Identifier: GPL-2.0-only + +# ----------------------------------------------------------------- +entries + +# ----------------------------------------------------------------- +# Status Register A +# ----------------------------------------------------------------- +# Status Register B +# ----------------------------------------------------------------- +# Status Register C +#96 4 r 0 status_c_rsvd +#100 1 r 0 uf_flag +#101 1 r 0 af_flag +#102 1 r 0 pf_flag +#103 1 r 0 irqf_flag +# ----------------------------------------------------------------- +# Status Register D +#104 7 r 0 status_d_rsvd +#111 1 r 0 valid_cmos_ram +# ----------------------------------------------------------------- +# Diagnostic Status Register +#112 8 r 0 diag_rsvd1 + +# ----------------------------------------------------------------- +0 120 r 0 reserved_memory + +# ----------------------------------------------------------------- +# RTC_BOOT_BYTE (coreboot hardcoded) +384 1 e 4 boot_option +388 4 h 0 reboot_counter + +# ----------------------------------------------------------------- +# coreboot config options: console +395 4 e 6 debug_level + +#400 8 r 0 reserved for century byte + +# coreboot config options: southbridge +408 1 e 1 nmi +409 2 e 7 power_on_after_fail +411 1 e 8 sata_mode + +# coreboot config options: EC +412 1 e 1 fan_full_speed + +# coreboot config options: northbridge +432 3 e 9 gfx_uma_size + +# SandyBridge MRC Scrambler Seed values +896 32 r 0 mrc_scrambler_seed +928 32 r 0 mrc_scrambler_seed_s3 +960 16 r 0 mrc_scrambler_seed_chk + +# coreboot config options: check sums +984 16 h 0 check_sum + +# ----------------------------------------------------------------- + +enumerations + +#ID value text +1 0 Disable +1 1 Enable +2 0 Enable +2 1 Disable +4 0 Fallback +4 1 Normal +6 0 Emergency +6 1 Alert +6 2 Critical +6 3 Error +6 4 Warning +6 5 Notice +6 6 Info +6 7 Debug +6 8 Spew +7 0 Disable +7 1 Enable +7 2 Keep +8 0 AHCI +8 1 Compatible +9 0 32M +9 1 64M +9 2 96M +9 3 128M +9 4 160M +9 5 192M +9 6 224M + + +# ----------------------------------------------------------------- +checksums + +checksum 392 447 984 diff --git a/src/mainboard/dell/optiplex_9010/data.vbt b/src/mainboard/dell/optiplex_9010/data.vbt Binary files differnew file mode 100644 index 0000000000..d1a95e8632 --- /dev/null +++ b/src/mainboard/dell/optiplex_9010/data.vbt diff --git a/src/mainboard/dell/optiplex_9010/devicetree.cb b/src/mainboard/dell/optiplex_9010/devicetree.cb new file mode 100644 index 0000000000..6a21d20b74 --- /dev/null +++ b/src/mainboard/dell/optiplex_9010/devicetree.cb @@ -0,0 +1,99 @@ +chip northbridge/intel/sandybridge + device cpu_cluster 0 on + chip cpu/intel/model_206ax + register "c1_acpower" = "1" + register "c1_battery" = "1" + register "c2_acpower" = "3" + register "c2_battery" = "3" + register "c3_acpower" = "5" + register "c3_battery" = "5" + register "tcc_offset" = "5" # TCC of 95C + device lapic 0 on end + device lapic 0xacac off end + end + end + device domain 0x0 on + subsystemid 0x1028 0x052c inherit + + device pci 00.0 on end # Host bridge Host bridge + device pci 01.0 on # PEG1 (blue slot1) + smbios_slot_desc "0xB6" "4" "SLOT1" "0x0D" + end + device pci 02.0 on end # Internal graphics VGA controller + device pci 06.0 off end # PEG2 + + chip southbridge/intel/bd82x6x # Intel Series 7 Panther Point PCH + register "gpe0_en" = "0x00000146" + register "alt_gp_smi_en" = "0x0004" + register "gpi2_routing" = "1" + register "gpi12_routing" = "2" + register "c2_latency" = "0x0065" + register "gen1_dec" = "0x007c0a01" + register "gen2_dec" = "0x007c0901" + register "gen3_dec" = "0x003c07e1" + register "gen4_dec" = "0x001c0901" + register "pcie_port_coalesce" = "1" + register "sata_interface_speed_support" = "0x3" + register "sata_port_map" = "0x7" + register "spi_lvscc" = "0x2005" + register "spi_uvscc" = "0x2005" + register "superspeed_capable_ports" = "0x0000000f" + register "xhci_overcurrent_mapping" = "0x08040201" + register "xhci_switchable_ports" = "0x0000000f" + device pci 14.0 on end # USB 3.0 Controller + device pci 16.0 off end # Management Engine Interface 1 + device pci 16.1 off end # Management Engine Interface 2 + device pci 16.2 off end # Management Engine IDE-R + device pci 16.3 off end # Management Engine KT + device pci 19.0 on end # Intel Gigabit Ethernet + device pci 1a.0 on end # USB2 EHCI #2 + device pci 1b.0 on end # High Definition Audio controller + device pci 1c.0 off end # PCIe Port #1 + device pci 1c.1 off end # PCIe Port #2 + device pci 1c.2 off end # PCIe Port #3 + device pci 1c.3 off end # PCIe Port #4 + device pci 1c.4 on # PCIe Port #5 + smbios_slot_desc "0xB6" "4" "SLOT2" "0x0A" + end + device pci 1c.5 on end # PCIe Port #6 + device pci 1c.6 on end # PCIe Port #7 + device pci 1c.7 on end # PCIe Port #8 + device pci 1d.0 on end # USB2 EHCI #1 + device pci 1e.0 off end # PCI bridge + device pci 1f.0 on # LPC bridge + chip drivers/pc80/tpm + device pnp 0c31.0 on end + end + chip superio/smsc/sch5545 + device pnp 2e.c on # LPC + io 0x60 = 0x2e + end + device pnp 2e.0 on # EMI + io 0x60 = 0xa40 + end + device pnp 2e.1 on # KBC/PS2M + io 0x60 = 0x60 + irq 0x70 = 1 + irq 0x72 = 12 + end + device pnp 2e.7 on # UART1 + io 0x60 = 0x3f8 + irq 0x70 = 4 + irq 0xf0 = 0x02 + end + device pnp 2e.8 off end # UART2 + device pnp 2e.a on # Runtime registers + io 0x60 = 0xa00 + irq 0x70 = 9 # PME + end + device pnp 2e.b off end # Floppy + device pnp 2e.11 off end # PP + end + end + device pci 1f.2 on end # SATA Controller 1 + device pci 1f.3 on end # SMBus + device pci 1f.5 off end # SATA Controller 2 + device pci 1f.6 on end # Thermal + end + end +end diff --git a/src/mainboard/dell/optiplex_9010/dsdt.asl b/src/mainboard/dell/optiplex_9010/dsdt.asl new file mode 100644 index 0000000000..6a6dcb4c36 --- /dev/null +++ b/src/mainboard/dell/optiplex_9010/dsdt.asl @@ -0,0 +1,32 @@ +/* SPDX-License-Identifier: GPL-2.0-only */ + +#include <acpi/acpi.h> +DefinitionBlock( + "dsdt.aml", + "DSDT", + 0x02, /* DSDT revision: ACPI 2.0 and up */ + OEM_ID, + ACPI_TABLE_CREATOR, + 0x20141018 /* OEM revision */ +) +{ + #include "acpi/platform.asl" + #include <cpu/intel/common/acpi/cpu.asl> + #include <southbridge/intel/common/acpi/platform.asl> + #include <southbridge/intel/bd82x6x/acpi/globalnvs.asl> + #include <southbridge/intel/common/acpi/sleepstates.asl> + + Scope (\_SB) + { + Device (PCI0) + { + #include <northbridge/intel/sandybridge/acpi/sandybridge.asl> + #include <southbridge/intel/bd82x6x/acpi/pch.asl> + Device (GLAN) + { + Name (_ADR, 0x00190000) + Name (_PRW, Package() { 13, 4 }) + } + } + } +} diff --git a/src/mainboard/dell/optiplex_9010/early_init.c b/src/mainboard/dell/optiplex_9010/early_init.c new file mode 100644 index 0000000000..5469c94f15 --- /dev/null +++ b/src/mainboard/dell/optiplex_9010/early_init.c @@ -0,0 +1,47 @@ +/* SPDX-License-Identifier: GPL-2.0-only */ + +#include <bootblock_common.h> +#include <device/pci_ops.h> +#include <northbridge/intel/sandybridge/sandybridge.h> +#include <southbridge/intel/bd82x6x/pch.h> +#include <superio/smsc/sch5545/sch5545.h> +#include <superio/smsc/sch5545/sch5545_emi.h> + +#include "sch5545_ec.h" + +const struct southbridge_usb_port mainboard_usb_ports[] = { + { 1, 6, 0 }, + { 1, 6, 0 }, + { 1, 1, 1 }, + { 1, 1, 1 }, + { 1, 1, 2 }, + { 1, 1, 2 }, + { 1, 6, 3 }, + { 1, 6, 3 }, + { 1, 6, 4 }, + { 1, 6, 4 }, + { 1, 6, 5 }, + { 1, 1, 5 }, + { 1, 1, 6 }, + { 1, 6, 6 }, +}; + +void bootblock_mainboard_early_init(void) +{ + /* + * FIXME: the board gets stuck in reset loop in + * mainboard_romstage_entry. Avoid that by clearing SSKPD + */ + pci_write_config32(HOST_BRIDGE, MCHBAR, (uintptr_t)DEFAULT_MCHBAR | 1); + pci_write_config32(HOST_BRIDGE, MCHBAR + 4, (0LL + (uintptr_t)DEFAULT_MCHBAR) >> 32); + MCHBAR16(SSKPD_HI) = 0; + + sch5545_early_init(0x2e); + /* Bare EC and SIO GPIO initialization which allows to enable serial port */ + sch5545_emi_init(0x2e); + sch5545_emi_disable_interrupts(); + sch5545_ec_early_init(); + + if (CONFIG(CONSOLE_SERIAL)) + sch5545_enable_uart(0x2e, 0); +} diff --git a/src/mainboard/dell/optiplex_9010/gma-mainboard.ads b/src/mainboard/dell/optiplex_9010/gma-mainboard.ads new file mode 100644 index 0000000000..74b50645e6 --- /dev/null +++ b/src/mainboard/dell/optiplex_9010/gma-mainboard.ads @@ -0,0 +1,19 @@ +-- SPDX-License-Identifier: GPL-2.0-or-later + +with HW.GFX.GMA; +with HW.GFX.GMA.Display_Probing; + +use HW.GFX.GMA; +use HW.GFX.GMA.Display_Probing; + +private package GMA.Mainboard is + + ports : constant Port_List := + (DP1, + DP2, + HDMI1, + HDMI2, + Analog, + others => Disabled); + +end GMA.Mainboard; diff --git a/src/mainboard/dell/optiplex_9010/gpio.c b/src/mainboard/dell/optiplex_9010/gpio.c new file mode 100644 index 0000000000..d01e6221a6 --- /dev/null +++ b/src/mainboard/dell/optiplex_9010/gpio.c @@ -0,0 +1,208 @@ +/* SPDX-License-Identifier: GPL-2.0-only */ + +#include <southbridge/intel/common/gpio.h> + +static const struct pch_gpio_set1 pch_gpio_set1_mode = { + .gpio0 = GPIO_MODE_NATIVE, + .gpio1 = GPIO_MODE_GPIO, /* CHASSIS_ID0 */ + .gpio2 = GPIO_MODE_GPIO, + .gpio3 = GPIO_MODE_GPIO, + .gpio4 = GPIO_MODE_GPIO, /* VGA_CBL_DET# */ + .gpio5 = GPIO_MODE_GPIO, + .gpio6 = GPIO_MODE_GPIO, /* PCH_HS_DET# (unused?) */ + .gpio7 = GPIO_MODE_GPIO, /* SKU2 */ + .gpio8 = GPIO_MODE_GPIO, + .gpio9 = GPIO_MODE_NATIVE, + .gpio10 = GPIO_MODE_NATIVE, + .gpio11 = GPIO_MODE_GPIO, /* PCIE_X4_WAKE*/ + .gpio12 = GPIO_MODE_NATIVE, + .gpio13 = GPIO_MODE_GPIO, /* PCIE_X1_WAKE (MT/DT only)*/ + .gpio14 = GPIO_MODE_GPIO, + .gpio15 = GPIO_MODE_GPIO, + .gpio16 = GPIO_MODE_GPIO, + .gpio17 = GPIO_MODE_GPIO, /* CHASSIS_ID1 */ + .gpio18 = GPIO_MODE_NATIVE, + .gpio19 = GPIO_MODE_NATIVE, + .gpio20 = GPIO_MODE_GPIO, /* FLEXBAY_HDR_CBL_DET# */ + .gpio21 = GPIO_MODE_GPIO, /* BOARD_REV0 */ + .gpio22 = GPIO_MODE_GPIO, + .gpio23 = GPIO_MODE_GPIO, + .gpio24 = GPIO_MODE_GPIO, + .gpio25 = GPIO_MODE_NATIVE, + .gpio26 = GPIO_MODE_NATIVE, + .gpio27 = GPIO_MODE_GPIO, + .gpio28 = GPIO_MODE_GPIO, + .gpio29 = GPIO_MODE_GPIO, + .gpio30 = GPIO_MODE_NATIVE, + .gpio31 = GPIO_MODE_GPIO, /* Password Clear Jumper */ +}; + +static const struct pch_gpio_set1 pch_gpio_set1_direction = { + .gpio1 = GPIO_DIR_INPUT, + .gpio2 = GPIO_DIR_INPUT, + .gpio3 = GPIO_DIR_INPUT, + .gpio4 = GPIO_DIR_INPUT, + .gpio5 = GPIO_DIR_INPUT, + .gpio6 = GPIO_DIR_INPUT, + .gpio7 = GPIO_DIR_INPUT, + .gpio8 = GPIO_DIR_OUTPUT, + .gpio11 = GPIO_DIR_INPUT, + .gpio13 = GPIO_DIR_INPUT, + .gpio14 = GPIO_DIR_OUTPUT, + .gpio15 = GPIO_DIR_OUTPUT, + .gpio16 = GPIO_DIR_INPUT, + .gpio17 = GPIO_DIR_INPUT, + .gpio20 = GPIO_DIR_INPUT, + .gpio21 = GPIO_DIR_INPUT, + .gpio22 = GPIO_DIR_INPUT, + .gpio23 = GPIO_DIR_INPUT, + .gpio24 = GPIO_DIR_INPUT, + .gpio27 = GPIO_DIR_OUTPUT, + .gpio28 = GPIO_DIR_OUTPUT, + .gpio29 = GPIO_DIR_OUTPUT, + .gpio31 = GPIO_DIR_INPUT, +}; + +static const struct pch_gpio_set1 pch_gpio_set1_level = { + .gpio8 = GPIO_LEVEL_HIGH, + .gpio14 = GPIO_LEVEL_HIGH, + .gpio15 = GPIO_LEVEL_LOW, + .gpio27 = GPIO_LEVEL_LOW, + .gpio28 = GPIO_LEVEL_LOW, + .gpio29 = GPIO_LEVEL_HIGH, +}; + +static const struct pch_gpio_set1 pch_gpio_set1_reset = { +}; + +static const struct pch_gpio_set1 pch_gpio_set1_invert = { + .gpio2 = GPIO_INVERT, + .gpio5 = GPIO_INVERT, + .gpio6 = GPIO_INVERT, + .gpio11 = GPIO_INVERT, + .gpio13 = GPIO_INVERT, +}; + +static const struct pch_gpio_set1 pch_gpio_set1_blink = { +}; + +static const struct pch_gpio_set2 pch_gpio_set2_mode = { + .gpio32 = GPIO_MODE_GPIO, /* SKU0 */ + .gpio33 = GPIO_MODE_GPIO, + .gpio34 = GPIO_MODE_GPIO, + .gpio35 = GPIO_MODE_GPIO, /* SKU1 */ + .gpio36 = GPIO_MODE_NATIVE, + .gpio37 = GPIO_MODE_NATIVE, + .gpio38 = GPIO_MODE_GPIO, /* CHASSIS_ID2 */ + .gpio39 = GPIO_MODE_GPIO, /* FP_PRESENCE# */ + .gpio40 = GPIO_MODE_NATIVE, + .gpio41 = GPIO_MODE_NATIVE, + .gpio42 = GPIO_MODE_NATIVE, + .gpio43 = GPIO_MODE_NATIVE, + .gpio44 = GPIO_MODE_GPIO, /* INTRUD_CBL_DET# */ + .gpio45 = GPIO_MODE_GPIO, /* COM_SER2_DET# (unused?) */ + .gpio46 = GPIO_MODE_GPIO, /* BOARD_REV1 */ + .gpio47 = GPIO_MODE_NATIVE, + .gpio48 = GPIO_MODE_GPIO, + .gpio49 = GPIO_MODE_GPIO, + .gpio50 = GPIO_MODE_NATIVE, + .gpio51 = GPIO_MODE_NATIVE, + .gpio52 = GPIO_MODE_NATIVE, + .gpio53 = GPIO_MODE_NATIVE, + .gpio54 = GPIO_MODE_NATIVE, + .gpio55 = GPIO_MODE_NATIVE, + .gpio56 = GPIO_MODE_NATIVE, + .gpio57 = GPIO_MODE_GPIO, + .gpio58 = GPIO_MODE_NATIVE, + .gpio59 = GPIO_MODE_NATIVE, + .gpio60 = GPIO_MODE_GPIO, + .gpio61 = GPIO_MODE_NATIVE, + .gpio62 = GPIO_MODE_NATIVE, + .gpio63 = GPIO_MODE_NATIVE, +}; + +static const struct pch_gpio_set2 pch_gpio_set2_direction = { + .gpio32 = GPIO_DIR_INPUT, + .gpio33 = GPIO_DIR_OUTPUT, + .gpio34 = GPIO_DIR_OUTPUT, + .gpio35 = GPIO_DIR_INPUT, + .gpio38 = GPIO_DIR_INPUT, + .gpio39 = GPIO_DIR_INPUT, + .gpio44 = GPIO_DIR_INPUT, + .gpio45 = GPIO_DIR_INPUT, + .gpio46 = GPIO_DIR_INPUT, + .gpio48 = GPIO_DIR_INPUT, + .gpio49 = GPIO_DIR_OUTPUT, + .gpio57 = GPIO_DIR_OUTPUT, + .gpio60 = GPIO_DIR_OUTPUT, + .gpio63 = GPIO_DIR_OUTPUT, +}; + +static const struct pch_gpio_set2 pch_gpio_set2_level = { + .gpio33 = GPIO_LEVEL_HIGH, + .gpio34 = GPIO_LEVEL_HIGH, + .gpio49 = GPIO_LEVEL_HIGH, + .gpio57 = GPIO_LEVEL_LOW, + .gpio60 = GPIO_LEVEL_HIGH, +}; + +static const struct pch_gpio_set2 pch_gpio_set2_reset = { +}; + +static const struct pch_gpio_set3 pch_gpio_set3_mode = { + .gpio64 = GPIO_MODE_NATIVE, + .gpio65 = GPIO_MODE_NATIVE, + .gpio66 = GPIO_MODE_NATIVE, + .gpio67 = GPIO_MODE_NATIVE, + .gpio68 = GPIO_MODE_GPIO, /* BOARD_REV2 */ + .gpio69 = GPIO_MODE_GPIO, /* USB_HDR_DET# */ + .gpio70 = GPIO_MODE_GPIO, /* FP_CHAS_DET# */ + .gpio71 = GPIO_MODE_GPIO, + .gpio72 = GPIO_MODE_GPIO, + .gpio73 = GPIO_MODE_GPIO, + .gpio74 = GPIO_MODE_GPIO, /* ME_MFG_MODE */ + .gpio75 = GPIO_MODE_NATIVE, +}; + +static const struct pch_gpio_set3 pch_gpio_set3_direction = { + .gpio68 = GPIO_DIR_INPUT, + .gpio69 = GPIO_DIR_INPUT, + .gpio70 = GPIO_DIR_INPUT, + .gpio71 = GPIO_DIR_OUTPUT, + .gpio72 = GPIO_DIR_OUTPUT, + .gpio73 = GPIO_DIR_INPUT, + .gpio74 = GPIO_DIR_OUTPUT, +}; + +static const struct pch_gpio_set3 pch_gpio_set3_level = { + .gpio71 = GPIO_LEVEL_HIGH, + .gpio72 = GPIO_LEVEL_HIGH, + .gpio74 = GPIO_LEVEL_HIGH, +}; + +static const struct pch_gpio_set3 pch_gpio_set3_reset = { + .gpio74 = GPIO_RESET_RSMRST, +}; + +const struct pch_gpio_map mainboard_gpio_map = { + .set1 = { + .mode = &pch_gpio_set1_mode, + .direction = &pch_gpio_set1_direction, + .level = &pch_gpio_set1_level, + .blink = &pch_gpio_set1_blink, + .invert = &pch_gpio_set1_invert, + .reset = &pch_gpio_set1_reset, + }, + .set2 = { + .mode = &pch_gpio_set2_mode, + .direction = &pch_gpio_set2_direction, + .level = &pch_gpio_set2_level, + .reset = &pch_gpio_set2_reset, + }, + .set3 = { + .mode = &pch_gpio_set3_mode, + .direction = &pch_gpio_set3_direction, + .level = &pch_gpio_set3_level, + .reset = &pch_gpio_set3_reset, + }, +}; diff --git a/src/mainboard/dell/optiplex_9010/hda_verb.c b/src/mainboard/dell/optiplex_9010/hda_verb.c new file mode 100644 index 0000000000..eab4ba9053 --- /dev/null +++ b/src/mainboard/dell/optiplex_9010/hda_verb.c @@ -0,0 +1,36 @@ +/* SPDX-License-Identifier: GPL-2.0-only */ + +#include <device/azalia_device.h> + +const u32 cim_verb_data[] = { + 0x10ec0269, /* Codec Vendor / Device ID: Realtek */ + 0x1028052c, /* Subsystem ID */ + + 11, /* Number of 4 dword sets */ + + AZALIA_SUBVENDOR(0, 0x1028052c), + AZALIA_PIN_CFG(0, 0x12, 0x411111f0), + AZALIA_PIN_CFG(0, 0x14, 0x99130110), + AZALIA_PIN_CFG(0, 0x17, 0x411111f0), + AZALIA_PIN_CFG(0, 0x18, 0x02a19830), + AZALIA_PIN_CFG(0, 0x19, 0x01a19840), + AZALIA_PIN_CFG(0, 0x1a, 0x411111f0), + AZALIA_PIN_CFG(0, 0x1b, 0x01014020), + AZALIA_PIN_CFG(0, 0x1d, 0x411111f0), + AZALIA_PIN_CFG(0, 0x1e, 0x411111f0), + AZALIA_PIN_CFG(0, 0x21, 0x0221402f), + + 0x80862806, /* Codec Vendor / Device ID: Intel */ + 0x80860101, /* Subsystem ID */ + + 4, /* Number of 4 dword sets */ + + AZALIA_SUBVENDOR(3, 0x80860101), + AZALIA_PIN_CFG(3, 0x05, 0x18560010), + AZALIA_PIN_CFG(3, 0x06, 0x18560020), + AZALIA_PIN_CFG(3, 0x07, 0x58560030), +}; + +const u32 pc_beep_verbs[0] = {}; + +AZALIA_ARRAY_SIZES; diff --git a/src/mainboard/dell/optiplex_9010/mainboard.c b/src/mainboard/dell/optiplex_9010/mainboard.c new file mode 100644 index 0000000000..4490c14a0d --- /dev/null +++ b/src/mainboard/dell/optiplex_9010/mainboard.c @@ -0,0 +1,191 @@ +/* SPDX-License-Identifier: GPL-2.0-only */ + +#include <bootstate.h> +#include <console/console.h> +#include <device/device.h> +#include <device/pci_ops.h> +#include <drivers/intel/gma/int15.h> +#include <southbridge/intel/bd82x6x/pch.h> +#include <southbridge/intel/common/gpio.h> +#include <superio/smsc/sch5545/sch5545.h> + +#include "sch5545_ec.h" + +#define SIO_PORT 0x2e + +#define GPIO_CHASSIS_ID0 1 +#define GPIO_VGA_CABLE_DET_L 4 +#define GPIO_SKU2 7 +#define GPIO_CHASSIS_ID1 17 +/* Internal USB header on mainboard */ +#define FLEXBAY_HEADER_CABLE_DET_L 20 +#define GPIO_BOARD_REV0 21 +/* Password clear jumper */ +#define GPIO_PSWD_CLR 31 +#define GPIO_SKU0 32 +#define GPIO_SKU1 35 +#define GPIO_CHASSIS_ID2 37 +/* Front panel presence */ +#define GPIO_FRONT_PANEL_PRESENT_L 39 +#define GPIO_INTRUDER_CABLE_DET_L 44 +#define GPIO_BOARD_REV1 46 +#define GPIO_BOARD_REV2 68 +/* Front USB 3.0 ports */ +#define GPIO_USB_HEADER_DET_L 69 +/* Differentiate between MT/DT on the Medium Tower and Desktop variants */ +#define GPIO_FRONT_PANEL_CHASSIS_DET_L 70 +/* + * This GPIO is connected to the transistor gate. If high, it will pull the + * HDA_SDO high. When strapped at PCH_PWROK it will enable the Flash Descriptor + * Security Override and disable ME after chipset bringup. Alternative method + * is to use the service jumper on the mainboard. + */ +#define GPIO_ME_MFG_MODE 74 + +/* These GPIOs are on SCH5545 */ + +/* Detect if the power switch cable is connected */ +#define SIO_GPIO_FP_CBL_DET_L 25 +/* Detect internal speaker connected to front cover */ +#define SIO_GPIO_PCSPKR_DET_L 31 + +static void mainboard_enable(struct device *dev) +{ + int pin_sts; + install_intel_vga_int15_handler(GMA_INT15_ACTIVE_LFP_NONE, + GMA_INT15_PANEL_FIT_DEFAULT, + GMA_INT15_BOOT_DISPLAY_DEFAULT, 0); + + pin_sts = get_gpio(GPIO_CHASSIS_ID0); + pin_sts |= get_gpio(GPIO_CHASSIS_ID1) << 1; + pin_sts |= get_gpio(GPIO_CHASSIS_ID2) << 2; + pin_sts |= get_gpio(GPIO_FRONT_PANEL_CHASSIS_DET_L) << 3; + + printk(BIOS_DEBUG, "Chassis type:"); + switch (pin_sts) { + case 0: + printk(BIOS_DEBUG, "MT\n"); + break; + case 3: + case 11: + printk(BIOS_DEBUG, "USFF\n"); + break; + case 4: + /* As per table in schematics, but don't know what this is */ + printk(BIOS_DEBUG, "Comoros\n"); + break; + case 1: + case 9: + case 5: + case 13: + printk(BIOS_DEBUG, "SFF\n"); + break; + case 8: + printk(BIOS_DEBUG, "DT\n"); + break; + default: + printk(BIOS_DEBUG, "Unknown chassis type %u\n", pin_sts); + break; + } + + pin_sts = get_gpio(GPIO_BOARD_REV0); + pin_sts |= get_gpio(GPIO_BOARD_REV1) << 1; + pin_sts |= get_gpio(GPIO_BOARD_REV2) << 2; + + printk(BIOS_DEBUG, "Board revision: %d\n", pin_sts); + + pin_sts = get_gpio(GPIO_SKU0); + pin_sts |= get_gpio(GPIO_SKU1) << 1; + pin_sts |= get_gpio(GPIO_SKU2) << 2; + + printk(BIOS_DEBUG, "SKU ID is %d:", pin_sts); + switch (pin_sts) { + case 0: + printk(BIOS_DEBUG, "TPM\n"); + break; + case 1: + printk(BIOS_DEBUG, "TCM\n"); + break; + case 2: + printk(BIOS_DEBUG, "Non TPM/TCM\n"); + break; + default: + printk(BIOS_DEBUG, "Unknown/reserved\n"); + break; + } + + printk(BIOS_DEBUG, "VGA cable %sconnected\n", + get_gpio(GPIO_VGA_CABLE_DET_L) ? "dis" : ""); + + printk(BIOS_DEBUG, "Flexbay %sattached to internal USB 2.0 header\n", + get_gpio(FLEXBAY_HEADER_CABLE_DET_L) ? "not " : ""); + + printk(BIOS_DEBUG, "Password clear jumper %sactive\n", + get_gpio(GPIO_PSWD_CLR) ? "in" : ""); + + if (!get_gpio(GPIO_FRONT_PANEL_PRESENT_L)) { + printk(BIOS_DEBUG, "Front panel cable connected\n"); + } else { + printk(BIOS_WARNING, "Front panel cable not connected!\n"); + printk(BIOS_WARNING, "Front USB 2.0 ports, SATA LED, microphone" + " and speaker jacks will not work!\n"); + printk(BIOS_WARNING, "Check the front panel cable!\n"); + } + + if (!get_gpio(GPIO_INTRUDER_CABLE_DET_L)) { + printk(BIOS_DEBUG, "Intruder cable connected\n"); + } else { + printk(BIOS_WARNING, "Intruder cable not connected!\n"); + printk(BIOS_WARNING, "Intrusion detection will not work!\n"); + printk(BIOS_WARNING, "Check the intruder cable!\n"); + } + + if (!get_gpio(GPIO_USB_HEADER_DET_L)) { + printk(BIOS_DEBUG, "Front USB 3.0 cable connected\n"); + } else { + printk(BIOS_WARNING, "Front USB 3.0 cable not connected!\n"); + printk(BIOS_WARNING, "Front USB 3.0 ports will not work!\n"); + printk(BIOS_WARNING, "Check the front USB 3.0 cable!\n"); + } +} + +static void mainboard_final(void *chip_info) +{ + int pin_sts; + struct device *dev = pcidev_on_root(0x1f, 0); + const u8 pirq_routing = 11; + + pci_write_config8(dev, PIRQA_ROUT, pirq_routing); + pci_write_config8(dev, PIRQB_ROUT, pirq_routing); + pci_write_config8(dev, PIRQC_ROUT, pirq_routing); + pci_write_config8(dev, PIRQD_ROUT, pirq_routing); + + pci_write_config8(dev, PIRQE_ROUT, pirq_routing); + pci_write_config8(dev, PIRQF_ROUT, pirq_routing); + pci_write_config8(dev, PIRQG_ROUT, pirq_routing); + pci_write_config8(dev, PIRQH_ROUT, pirq_routing); + + pin_sts = sch5545_get_gpio(SIO_PORT, SIO_GPIO_FP_CBL_DET_L); + + if (pin_sts != -1) { + if (pin_sts) { + printk(BIOS_WARNING, "Power switch cable not connected!\n"); + printk(BIOS_WARNING, "Check power switch cable!\n"); + } else { + printk(BIOS_DEBUG, "Power switch cable connected\n"); + } + } + + pin_sts = sch5545_get_gpio(SIO_PORT, SIO_GPIO_PCSPKR_DET_L); + + if (pin_sts != -1) + printk(BIOS_DEBUG, "Internal chassis PC speaker %sconnected\n", + pin_sts ? "not " : ""); +} + +struct chip_operations mainboard_ops = { + .enable_dev = mainboard_enable, + .final = mainboard_final, +}; + +BOOT_STATE_INIT_ENTRY(BS_POST_DEVICE, BS_ON_EXIT, sch5545_ec_hwm_init, NULL); diff --git a/src/mainboard/dell/optiplex_9010/romstage.c b/src/mainboard/dell/optiplex_9010/romstage.c new file mode 100644 index 0000000000..36af6e49c0 --- /dev/null +++ b/src/mainboard/dell/optiplex_9010/romstage.c @@ -0,0 +1,53 @@ +/* SPDX-License-Identifier: GPL-2.0-only */ + +#include <stdint.h> +#include <arch/io.h> +#include <console/console.h> +#include <northbridge/intel/sandybridge/sandybridge.h> +#include <northbridge/intel/sandybridge/raminit_native.h> +#include <southbridge/intel/bd82x6x/pch.h> +#include <superio/smsc/sch5545/sch5545.h> +#include <superio/smsc/sch5545/sch5545_emi.h> + +#include "sch5545_ec.h" + +void mainboard_early_init(int s3resume) +{ + uint16_t ec_fw_version; + + /* + * We do EC initialization in romstage, because it makes no sense to + * bloat the bootblock any more. Secondly, the EC expects to receive + * correct initialization sequence from the host in the time window of + * about 3-5 seconds since system reset. If it doesn't receive the + * initialization sequence, it enters an error path which results in + * fans spinned up to high speed. In this state EC doesn't respond to + * further messages sent over EMI. The issue appears after power + * failure, where EC loses its configuration. For this particular + * reasons we do the initialization in romstage instead of ramstage. + */ + sch5545_emi_init(0x2e); + if (sch5545_emi_get_int_mask_high()) + printk(BIOS_SPEW, "EC interrupt mask MSB is not 0\n"); + + sch5545_ec_hwm_early_init(); + + if (!s3resume) { + ec_fw_version = sch5545_get_ec_fw_version(); + printk(BIOS_DEBUG, "SCH5545 EC firmware version %04x\n", ec_fw_version); + sch5545_update_ec_firmware(ec_fw_version); + } + printk(BIOS_DEBUG, "EC early init complete.\n"); + + /* Disable SMIs and clear SMI status */ + outb(0, SCH5545_RUNTIME_REG_BASE + SCH5545_RR_SMI_EN); + outb(SCH5545_SMI_GLOBAL_STS, SCH5545_RUNTIME_REG_BASE + SCH5545_RR_SMI_STS); +} + +void mainboard_get_spd(spd_raw_data *spd, bool id_only) +{ + read_spd(&spd[0], 0x50, id_only); + read_spd(&spd[1], 0x51, id_only); + read_spd(&spd[2], 0x52, id_only); + read_spd(&spd[3], 0x53, id_only); +} diff --git a/src/mainboard/dell/optiplex_9010/sch5545_ec.c b/src/mainboard/dell/optiplex_9010/sch5545_ec.c new file mode 100644 index 0000000000..401345254d --- /dev/null +++ b/src/mainboard/dell/optiplex_9010/sch5545_ec.c @@ -0,0 +1,726 @@ +/* SPDX-License-Identifier: GPL-2.0-only */ + +#include <cbfs.h> +#include <cf9_reset.h> +#include <string.h> +#include <option.h> +#include <arch/io.h> +#include <cpu/x86/msr.h> +#include <console/console.h> +#include <cpu/intel/model_206ax/model_206ax.h> +#include <southbridge/intel/common/gpio.h> +#include <superio/smsc/sch5545/sch5545.h> +#include <superio/smsc/sch5545/sch5545_emi.h> + +#include "sch5545_ec.h" + +#define GPIO_CHASSIS_ID0 1 +#define GPIO_CHASSIS_ID1 17 +#define GPIO_CHASSIS_ID2 37 +#define GPIO_FRONT_PANEL_CHASSIS_DET_L 70 + +enum { + TDP_16 = 0x10, + TDP_32 = 0x20, + TDP_COMMON = 0xff, +}; + +typedef struct ec_val_reg_tdp { + uint8_t val; + uint16_t reg; + uint8_t tdp; +} ec_chassis_tdp_t; + +static const struct ec_val_reg ec_hwm_init_seq[] = { + { 0xa0, 0x02fc }, + { 0x32, 0x02fd }, + { 0x77, 0x0005 }, + { 0x0f, 0x0018 }, + { 0x2f, 0x0019 }, + { 0x2f, 0x001a }, + { 0x33, 0x008a }, + { 0x33, 0x008b }, + { 0x33, 0x008c }, + { 0x10, 0x00ba }, + { 0xff, 0x00d1 }, + { 0xff, 0x00d6 }, + { 0xff, 0x00db }, + { 0x00, 0x0048 }, + { 0x00, 0x0049 }, + { 0x00, 0x007a }, + { 0x00, 0x007b }, + { 0x00, 0x007c }, + { 0x00, 0x0080 }, + { 0x00, 0x0081 }, + { 0x00, 0x0082 }, + { 0xbb, 0x0083 }, + { 0xb0, 0x0084 }, + { 0x88, 0x01a1 }, + { 0x80, 0x01a4 }, + { 0x00, 0x0088 }, + { 0x00, 0x0089 }, + { 0x02, 0x00a0 }, + { 0x02, 0x00a1 }, + { 0x02, 0x00a2 }, + { 0x04, 0x00a4 }, + { 0x04, 0x00a5 }, + { 0x04, 0x00a6 }, + { 0x00, 0x00ab }, + { 0x3f, 0x00ad }, + { 0x07, 0x00b7 }, + { 0x50, 0x0062 }, + { 0x46, 0x0063 }, + { 0x50, 0x0064 }, + { 0x46, 0x0065 }, + { 0x50, 0x0066 }, + { 0x46, 0x0067 }, + { 0x98, 0x0057 }, + { 0x98, 0x0059 }, + { 0x7c, 0x0061 }, + { 0x00, 0x01bc }, + { 0x00, 0x01bd }, + { 0x00, 0x01bb }, + { 0xdd, 0x0085 }, + { 0xdd, 0x0086 }, + { 0x07, 0x0087 }, + { 0x5e, 0x0090 }, + { 0x5e, 0x0091 }, + { 0x5d, 0x0095 }, + { 0x00, 0x0096 }, + { 0x00, 0x0097 }, + { 0x00, 0x009b }, + { 0x86, 0x00ae }, + { 0x86, 0x00af }, + { 0x67, 0x00b3 }, + { 0xff, 0x00c4 }, + { 0xff, 0x00c5 }, + { 0xff, 0x00c9 }, + { 0x01, 0x0040 }, + { 0x00, 0x02fc }, + { 0x9a, 0x02b3 }, + { 0x05, 0x02b4 }, + { 0x01, 0x02cc }, + { 0x4c, 0x02d0 }, + { 0x01, 0x02d2 }, + { 0x01, 0x006f }, + { 0x02, 0x0070 }, + { 0x03, 0x0071 }, +}; + + +static const ec_chassis_tdp_t ec_hwm_chassis3[] = { + { 0x33, 0x0005, TDP_COMMON }, + { 0x2f, 0x0018, TDP_COMMON }, + { 0x2f, 0x0019, TDP_COMMON }, + { 0x2f, 0x001a, TDP_COMMON }, + { 0x00, 0x0080, TDP_COMMON }, + { 0x00, 0x0081, TDP_COMMON }, + { 0xbb, 0x0083, TDP_COMMON }, + { 0x8a, 0x0085, TDP_16 }, + { 0x2c, 0x0086, TDP_16 }, + { 0x66, 0x008a, TDP_16 }, + { 0x5b, 0x008b, TDP_16 }, + { 0x65, 0x0090, TDP_COMMON }, + { 0x70, 0x0091, TDP_COMMON }, + { 0x86, 0x0092, TDP_COMMON }, + { 0xa4, 0x0096, TDP_COMMON }, + { 0xa4, 0x0097, TDP_COMMON }, + { 0xa4, 0x0098, TDP_COMMON }, + { 0xa4, 0x009b, TDP_COMMON }, + { 0x0e, 0x00a0, TDP_COMMON }, + { 0x0e, 0x00a1, TDP_COMMON }, + { 0x7c, 0x00ae, TDP_COMMON }, + { 0x86, 0x00af, TDP_COMMON }, + { 0x95, 0x00b0, TDP_COMMON }, + { 0x9a, 0x00b3, TDP_COMMON }, + { 0x08, 0x00b6, TDP_COMMON }, + { 0x08, 0x00b7, TDP_COMMON }, + { 0x64, 0x00ea, TDP_COMMON }, + { 0xff, 0x00ef, TDP_COMMON }, + { 0x15, 0x00f8, TDP_COMMON }, + { 0x00, 0x00f9, TDP_COMMON }, + { 0x30, 0x00f0, TDP_COMMON }, + { 0x01, 0x00fd, TDP_COMMON }, + { 0x88, 0x01a1, TDP_COMMON }, + { 0x08, 0x01a2, TDP_COMMON }, + { 0x08, 0x01b1, TDP_COMMON }, + { 0x94, 0x01be, TDP_COMMON }, + { 0x94, 0x0280, TDP_16 }, + { 0x11, 0x0281, TDP_16 }, + { 0x03, 0x0282, TDP_COMMON }, + { 0x0a, 0x0283, TDP_COMMON }, + { 0x80, 0x0284, TDP_COMMON }, + { 0x03, 0x0285, TDP_COMMON }, + { 0x68, 0x0288, TDP_16 }, + { 0x10, 0x0289, TDP_16 }, + { 0x03, 0x028a, TDP_COMMON }, + { 0x0a, 0x028b, TDP_COMMON }, + { 0x80, 0x028c, TDP_COMMON }, + { 0x03, 0x028d, TDP_COMMON }, +}; + +static const ec_chassis_tdp_t ec_hwm_chassis4[] = { + { 0x33, 0x0005, TDP_COMMON }, + { 0x2f, 0x0018, TDP_COMMON }, + { 0x2f, 0x0019, TDP_COMMON }, + { 0x2f, 0x001a, TDP_COMMON }, + { 0x00, 0x0080, TDP_COMMON }, + { 0x00, 0x0081, TDP_COMMON }, + { 0xbb, 0x0083, TDP_COMMON }, + { 0x99, 0x0085, TDP_32 }, + { 0x98, 0x0085, TDP_16 }, + { 0xbc, 0x0086, TDP_32 }, + { 0x1c, 0x0086, TDP_16 }, + { 0x39, 0x008a, TDP_32 }, + { 0x3d, 0x008a, TDP_16 }, + { 0x40, 0x008b, TDP_32 }, + { 0x43, 0x008b, TDP_16 }, + { 0x68, 0x0090, TDP_COMMON }, + { 0x5e, 0x0091, TDP_COMMON }, + { 0x86, 0x0092, TDP_COMMON }, + { 0xa4, 0x0096, TDP_COMMON }, + { 0xa4, 0x0097, TDP_COMMON }, + { 0xa4, 0x0098, TDP_COMMON }, + { 0xa4, 0x009b, TDP_COMMON }, + { 0x0c, 0x00a0, TDP_COMMON }, + { 0x0c, 0x00a1, TDP_COMMON }, + { 0x72, 0x00ae, TDP_COMMON }, + { 0x7c, 0x00af, TDP_COMMON }, + { 0x9a, 0x00b0, TDP_COMMON }, + { 0x7c, 0x00b3, TDP_COMMON }, + { 0x08, 0x00b6, TDP_COMMON }, + { 0x08, 0x00b7, TDP_COMMON }, + { 0x64, 0x00ea, TDP_COMMON }, + { 0xff, 0x00ef, TDP_COMMON }, + { 0x15, 0x00f8, TDP_COMMON }, + { 0x00, 0x00f9, TDP_COMMON }, + { 0x30, 0x00f0, TDP_COMMON }, + { 0x01, 0x00fd, TDP_COMMON }, + { 0x88, 0x01a1, TDP_COMMON }, + { 0x08, 0x01a2, TDP_COMMON }, + { 0x08, 0x01b1, TDP_COMMON }, + { 0x90, 0x01be, TDP_COMMON }, + { 0x94, 0x0280, TDP_32 }, + { 0x11, 0x0281, TDP_32 }, + { 0x68, 0x0280, TDP_16 }, + { 0x10, 0x0281, TDP_16 }, + { 0x03, 0x0282, TDP_COMMON }, + { 0x0a, 0x0283, TDP_COMMON }, + { 0x80, 0x0284, TDP_COMMON }, + { 0x03, 0x0285, TDP_COMMON }, + { 0xa0, 0x0288, TDP_32 }, + { 0x0f, 0x0289, TDP_32 }, + { 0xd8, 0x0288, TDP_16 }, + { 0x0e, 0x0289, TDP_16 }, + { 0x03, 0x028a, TDP_COMMON }, + { 0x0a, 0x028b, TDP_COMMON }, + { 0x80, 0x028c, TDP_COMMON }, + { 0x03, 0x028d, TDP_COMMON }, +}; + +static const ec_chassis_tdp_t ec_hwm_chassis5[] = { + { 0x33, 0x0005, TDP_COMMON }, + { 0x2f, 0x0018, TDP_COMMON }, + { 0x2f, 0x0019, TDP_COMMON }, + { 0x2f, 0x001a, TDP_COMMON }, + { 0x00, 0x0080, TDP_COMMON }, + { 0x00, 0x0081, TDP_COMMON }, + { 0xbb, 0x0083, TDP_COMMON }, + { 0x89, 0x0085, TDP_32 }, + { 0x99, 0x0085, TDP_16 }, + { 0x9c, 0x0086, TDP_COMMON }, + { 0x39, 0x008a, TDP_32 }, + { 0x42, 0x008a, TDP_16 }, + { 0x6b, 0x008b, TDP_32 }, + { 0x74, 0x008b, TDP_16 }, + { 0x5e, 0x0091, TDP_COMMON }, + { 0x86, 0x0092, TDP_COMMON }, + { 0xa4, 0x0096, TDP_COMMON }, + { 0xa4, 0x0097, TDP_COMMON }, + { 0xa4, 0x0098, TDP_COMMON }, + { 0xa4, 0x009b, TDP_COMMON }, + { 0x0c, 0x00a0, TDP_COMMON }, + { 0x0c, 0x00a1, TDP_COMMON }, + { 0x7c, 0x00ae, TDP_COMMON }, + { 0x7c, 0x00af, TDP_COMMON }, + { 0x9a, 0x00b0, TDP_COMMON }, + { 0x7c, 0x00b3, TDP_COMMON }, + { 0x08, 0x00b6, TDP_COMMON }, + { 0x08, 0x00b7, TDP_COMMON }, + { 0x64, 0x00ea, TDP_COMMON }, + { 0xff, 0x00ef, TDP_COMMON }, + { 0x15, 0x00f8, TDP_COMMON }, + { 0x00, 0x00f9, TDP_COMMON }, + { 0x30, 0x00f0, TDP_COMMON }, + { 0x01, 0x00fd, TDP_COMMON }, + { 0x88, 0x01a1, TDP_COMMON }, + { 0x08, 0x01a2, TDP_COMMON }, + { 0x08, 0x01b1, TDP_COMMON }, + { 0x90, 0x01be, TDP_COMMON }, + { 0x94, 0x0280, TDP_32 }, + { 0x11, 0x0281, TDP_32 }, + { 0x3c, 0x0280, TDP_16 }, + { 0x0f, 0x0281, TDP_16 }, + { 0x03, 0x0282, TDP_COMMON }, + { 0x0a, 0x0283, TDP_COMMON }, + { 0x80, 0x0284, TDP_COMMON }, + { 0x03, 0x0285, TDP_COMMON }, + { 0x60, 0x0288, TDP_32 }, + { 0x09, 0x0289, TDP_32 }, + { 0x98, 0x0288, TDP_16 }, + { 0x08, 0x0289, TDP_16 }, + { 0x03, 0x028a, TDP_COMMON }, + { 0x0a, 0x028b, TDP_COMMON }, + { 0x80, 0x028c, TDP_COMMON }, + { 0x03, 0x028d, TDP_COMMON }, +}; + +static const ec_chassis_tdp_t ec_hwm_chassis6[] = { + { 0x33, 0x0005, TDP_COMMON }, + { 0x2f, 0x0018, TDP_COMMON }, + { 0x2f, 0x0019, TDP_COMMON }, + { 0x2f, 0x001a, TDP_COMMON }, + { 0x00, 0x0080, TDP_COMMON }, + { 0x00, 0x0081, TDP_COMMON }, + { 0xbb, 0x0083, TDP_COMMON }, + { 0x99, 0x0085, TDP_32 }, + { 0x98, 0x0085, TDP_16 }, + { 0xdc, 0x0086, TDP_32 }, + { 0x9c, 0x0086, TDP_16 }, + { 0x3d, 0x008a, TDP_32 }, + { 0x43, 0x008a, TDP_16 }, + { 0x4e, 0x008b, TDP_32 }, + { 0x47, 0x008b, TDP_16 }, + { 0x6d, 0x0090, TDP_COMMON }, + { 0x5f, 0x0091, TDP_32 }, + { 0x61, 0x0091, TDP_16 }, + { 0x86, 0x0092, TDP_COMMON }, + { 0xa4, 0x0096, TDP_COMMON }, + { 0xa4, 0x0097, TDP_COMMON }, + { 0xa4, 0x0098, TDP_COMMON }, + { 0xa4, 0x009b, TDP_COMMON }, + { 0x0e, 0x00a0, TDP_COMMON }, + { 0x0e, 0x00a1, TDP_COMMON }, + { 0x7c, 0x00ae, TDP_COMMON }, + { 0x7c, 0x00af, TDP_COMMON }, + { 0x98, 0x00b0, TDP_32 }, + { 0x9a, 0x00b0, TDP_16 }, + { 0x9a, 0x00b3, TDP_COMMON }, + { 0x08, 0x00b6, TDP_COMMON }, + { 0x08, 0x00b7, TDP_COMMON }, + { 0x64, 0x00ea, TDP_COMMON }, + { 0xff, 0x00ef, TDP_COMMON }, + { 0x15, 0x00f8, TDP_COMMON }, + { 0x00, 0x00f9, TDP_COMMON }, + { 0x30, 0x00f0, TDP_COMMON }, + { 0x01, 0x00fd, TDP_COMMON }, + { 0x88, 0x01a1, TDP_COMMON }, + { 0x08, 0x01a2, TDP_COMMON }, + { 0x08, 0x01b1, TDP_COMMON }, + { 0x97, 0x01be, TDP_32 }, + { 0x95, 0x01be, TDP_16 }, + { 0x68, 0x0280, TDP_32 }, + { 0x10, 0x0281, TDP_32 }, + { 0xd8, 0x0280, TDP_16 }, + { 0x0e, 0x0281, TDP_16 }, + { 0x03, 0x0282, TDP_COMMON }, + { 0x0a, 0x0283, TDP_COMMON }, + { 0x80, 0x0284, TDP_COMMON }, + { 0x03, 0x0285, TDP_COMMON }, + { 0xe4, 0x0288, TDP_32 }, + { 0x0c, 0x0289, TDP_32 }, + { 0x10, 0x0288, TDP_16 }, + { 0x0e, 0x0289, TDP_16 }, + { 0x03, 0x028a, TDP_COMMON }, + { 0x0a, 0x028b, TDP_COMMON }, + { 0x80, 0x028c, TDP_COMMON }, + { 0x03, 0x028d, TDP_COMMON }, +}; + + + +static uint8_t send_mbox_msg_with_int(uint8_t mbox_message) +{ + uint8_t int_sts, int_cond; + + sch5545_emi_h2ec_mbox_write(mbox_message); + + do { + int_sts = sch5545_emi_get_int_src_low(); + int_cond = int_sts & 0x71; + } while (int_cond == 0); + + sch5545_emi_set_int_src_low(int_cond); + + if ((int_sts & 1) == 0) + return 0; + + if (sch5545_emi_ec2h_mbox_read() == mbox_message) + return 1; + + return 0; +} + +static uint8_t send_mbox_msg_simple(uint8_t mbox_message) +{ + uint8_t int_sts; + + sch5545_emi_h2ec_mbox_write(mbox_message); + + do { + int_sts = sch5545_emi_get_int_src_low(); + if ((int_sts & 70) != 0) + return 0; + } while ((int_sts & 1) == 0); + + if (sch5545_emi_ec2h_mbox_read() == mbox_message) + return 1; + + return 0; +} + +static void ec_check_mbox_and_int_status(uint8_t int_src, uint8_t mbox_msg) +{ + uint8_t val; + + val = sch5545_emi_ec2h_mbox_read(); + if (val != mbox_msg) + printk(BIOS_SPEW, "EC2H mailbox should be %02x, is %02x\n", mbox_msg, val); + + val = sch5545_emi_get_int_src_low(); + if (val != int_src) + printk(BIOS_SPEW, "EC INT SRC should be %02x, is %02x\n", int_src, val); + + sch5545_emi_set_int_src_low(val); +} + +static uint8_t ec_read_write_reg(uint8_t ldn, uint16_t reg, uint8_t *value, uint8_t rw_bit) +{ + uint8_t int_mask_bckup, ret = 0; + rw_bit &= 1; + + int_mask_bckup = sch5545_emi_get_int_mask_low(); + sch5545_emi_set_int_mask_low(0); + + sch5545_emi_ec_write16(0x8000, (ldn << 1) | 0x100 | rw_bit); + if (rw_bit) + sch5545_emi_ec_write32(0x8004, (reg << 16) | *value); + else + sch5545_emi_ec_write32(0x8004, reg << 16); + + ret = send_mbox_msg_with_int(1); + if (ret && !rw_bit) + *value = sch5545_emi_ec_read8(0x8004); + else if (ret != 1 && rw_bit) + printk(BIOS_WARNING, "EC mailbox returned unexpected value " + "when writing %02x to %04x\n", *value, reg); + else if (ret != 1 && !rw_bit) + printk(BIOS_WARNING, "EC mailbox returned unexpected value " + "when reading %04x\n", reg); + + sch5545_emi_set_int_mask_low(int_mask_bckup); + + return ret; +} + +uint16_t sch5545_get_ec_fw_version(void) +{ + uint8_t val; + uint16_t ec_fw_version; + + /* Read the FW version currently loaded used by EC */ + ec_read_write_reg(EC_HWM_LDN, 0x2ad, &val, READ_OP); + ec_fw_version = (val << 8); + ec_read_write_reg(EC_HWM_LDN, 0x2ae, &val, READ_OP); + ec_fw_version |= val; + ec_read_write_reg(EC_HWM_LDN, 0x2ac, &val, READ_OP); + ec_read_write_reg(EC_HWM_LDN, 0x2fd, &val, READ_OP); + ec_read_write_reg(EC_HWM_LDN, 0x2b0, &val, READ_OP); + + return ec_fw_version; +} + +void sch5545_update_ec_firmware(uint16_t ec_version) +{ + uint8_t status; + uint16_t ec_fw_version; + uint32_t *ec_fw_file; + size_t ec_fw_file_size; + + ec_fw_file = cbfs_boot_map_with_leak("sch5545_ecfw.bin", CBFS_TYPE_RAW, + &ec_fw_file_size); + + if (!ec_fw_file || ec_fw_file_size != 0x1750) { + printk(BIOS_ERR, "EC firmware file not found in CBFS!\n"); + printk(BIOS_ERR, "The fans will keep running at maximum speed.\n"); + return; + } + + ec_fw_version = ec_fw_file[3] & 0xffff; + + /* + * After power failure EC loses its configuration. The currently used firmware version + * by EC will be reported as 0x0000. In such case EC firmware needs to be uploaded. + */ + if (ec_version != ec_fw_version) { + printk(BIOS_INFO, "SCH5545 EC is not functional, probably due to power " + "failure\n"); + printk(BIOS_INFO, "Uploading EC firmware (version %04x) to SCH5545\n", + ec_fw_version); + + if (!send_mbox_msg_simple(0x03)) { + printk(BIOS_WARNING, "EC didn't accept FW upload start signal\n"); + printk(BIOS_WARNING, "EC firmware update failed!\n"); + return; + } + + sch5545_emi_ec_write32_bulk(0x8100, ec_fw_file, ec_fw_file_size); + + status = send_mbox_msg_simple(0x04); + status += send_mbox_msg_simple(0x06); + + if (status != 2) + printk(BIOS_WARNING, "EC firmware update failed!\n"); + + if (ec_fw_version != sch5545_get_ec_fw_version()) { + printk(BIOS_ERR, "EC firmware update failed!\n"); + printk(BIOS_ERR, "The fans will keep running at maximum speed\n"); + } else { + printk(BIOS_INFO, "EC firmware update success\n"); + /* + * The vendor BIOS does a full reset after EC firmware update. Most + * likely because the fans are adapting very slowly after automatic fan + * control is enabled. This makes huge noise. To avoid it, also do the + * full reset. On next boot, it will not be necessary. + */ + full_reset(); + } + } else { + printk(BIOS_INFO, "SCH5545 EC firmware up to date (version %04x)\n", + ec_version); + } +} + +void sch5545_ec_hwm_early_init(void) +{ + uint8_t val; + int i; + + printk(BIOS_DEBUG, "%s\n", __func__); + + ec_check_mbox_and_int_status(0x20, 0x01); + + ec_read_write_reg(2, 0xcb, &val, READ_OP); + ec_read_write_reg(2, 0xb8, &val, READ_OP); + + for (i = 0; i < ARRAY_SIZE(ec_hwm_init_seq); i++) { + val = ec_hwm_init_seq[i].val; + ec_read_write_reg(EC_HWM_LDN, ec_hwm_init_seq[i].reg, &val, + WRITE_OP); + } + + ec_check_mbox_and_int_status(0x01, 0x01); +} + +static uint8_t get_sku_tdp_config(void) +{ + msr_t msr; + uint32_t power_unit, tdp; + /* Get units */ + msr = rdmsr(MSR_PKG_POWER_SKU_UNIT); + power_unit = msr.lo & 0xf; + + /* Get power defaults for this SKU */ + msr = rdmsr(MSR_PKG_POWER_SKU); + tdp = msr.lo & 0x7fff; + + /* These numbers will determine which settings to use to init EC */ + if ((tdp >> power_unit) < 66) + return 16; + else + return 32; +} + +static uint8_t get_chassis_type(void) +{ + uint8_t chassis_id; + + chassis_id = get_gpio(GPIO_CHASSIS_ID0); + chassis_id |= get_gpio(GPIO_CHASSIS_ID1) << 1; + chassis_id |= get_gpio(GPIO_CHASSIS_ID2) << 2; + chassis_id |= get_gpio(GPIO_FRONT_PANEL_CHASSIS_DET_L) << 3; + + /* This mapping will determine which EC init sequence to use */ + switch (chassis_id) { + case 0x0: + return 5; + case 0x8: + return 4; + case 0x3: + case 0xb: + return 3; + case 0x1: + case 0x9: + case 0x5: + case 0xd: + return 6; + default: + printk(BIOS_DEBUG, "Unknown chassis ID %x\n", chassis_id); + break; + } + + return 0xff; +} + +static void ec_hwm_init_late(const ec_chassis_tdp_t *ec_hwm_sequence, size_t size) +{ + unsigned int i; + uint8_t val; + uint8_t tdp_config = get_sku_tdp_config(); + + for (i = 0; i < size; i++) { + if (ec_hwm_sequence[i].tdp == tdp_config || + ec_hwm_sequence[i].tdp == TDP_COMMON) { + val = ec_hwm_sequence[i].val; + ec_read_write_reg(EC_HWM_LDN, ec_hwm_sequence[i].reg, &val, WRITE_OP); + } + } +} + +static void prepare_for_hwm_ec_sequence(uint8_t write_only, uint8_t *value) +{ + uint16_t reg; + uint8_t val; + + if (write_only == 1) { + val = *value; + reg = 0x02fc; + } else { + if (value != NULL) + ec_read_write_reg(EC_HWM_LDN, 0x02fc, value, READ_OP); + val = 0xa0; + ec_read_write_reg(EC_HWM_LDN, 0x2fc, &val, WRITE_OP); + val = 0x32; + reg = 0x02fd; + } + + ec_read_write_reg(1, reg, &val, WRITE_OP); +} + +void sch5545_ec_hwm_init(void *unused) +{ + uint8_t val, val_2fc, chassis_type, fan_speed_full = 0; + + printk(BIOS_DEBUG, "%s\n", __func__); + sch5545_emi_init(0x2e); + + chassis_type = get_chassis_type(); + + ec_read_write_reg(EC_HWM_LDN, 0x0048, &val, READ_OP); + ec_read_write_reg(EC_HWM_LDN, 0x0048, &val, WRITE_OP); + ec_read_write_reg(EC_HWM_LDN, 0x0042, &val, READ_OP); + ec_read_write_reg(EC_HWM_LDN, 0x0048, &val, READ_OP); + val |= 0x02; + ec_read_write_reg(EC_HWM_LDN, 0x0048, &val, WRITE_OP); + ec_read_write_reg(EC_HWM_LDN, 0x0048, &val, READ_OP); + ec_read_write_reg(EC_HWM_LDN, 0x0048, &val, WRITE_OP); + ec_read_write_reg(EC_HWM_LDN, 0x0042, &val, READ_OP); + ec_read_write_reg(EC_HWM_LDN, 0x0048, &val, READ_OP); + val |= 0x04; + ec_read_write_reg(EC_HWM_LDN, 0x0048, &val, WRITE_OP); + ec_read_write_reg(EC_HWM_LDN, 0x0081, &val, READ_OP); + ec_read_write_reg(EC_HWM_LDN, 0x0027, &val, READ_OP); + + ec_check_mbox_and_int_status(0x00, 0x01); + + prepare_for_hwm_ec_sequence(0, &val_2fc); + + if (chassis_type != 0xff) { + printk(BIOS_DEBUG, "Performing HWM init for chassis %d\n", chassis_type); + switch (chassis_type) { + case 3: + ec_hwm_init_late(ec_hwm_chassis3, ARRAY_SIZE(ec_hwm_chassis3)); + break; + case 4: + ec_hwm_init_late(ec_hwm_chassis4, ARRAY_SIZE(ec_hwm_chassis4)); + break; + case 5: + ec_hwm_init_late(ec_hwm_chassis6, ARRAY_SIZE(ec_hwm_chassis5)); + break; + case 6: + ec_hwm_init_late(ec_hwm_chassis6, ARRAY_SIZE(ec_hwm_chassis6)); + break; + } + } + + if (CONFIG_MAX_CPUS > 2) { + val = 0x30; + ec_read_write_reg(EC_HWM_LDN, 0x009e, &val, WRITE_OP); + ec_read_write_reg(EC_HWM_LDN, 0x00ea, &val, READ_OP); + ec_read_write_reg(EC_HWM_LDN, 0x00eb, &val, WRITE_OP); + } + + ec_read_write_reg(EC_HWM_LDN, 0x02fc, &val_2fc, WRITE_OP); + + if (get_option(&fan_speed_full, "fan_full_speed") != CB_SUCCESS) + printk(BIOS_INFO, "fan_full_speed CMOS option not found. " + "Fans will be set up for automatic control\n"); + + if (fan_speed_full) { + ec_read_write_reg(EC_HWM_LDN, 0x0080, &val, READ_OP); + val |= 0x60; + ec_read_write_reg(EC_HWM_LDN, 0x0080, &val, WRITE_OP); + ec_read_write_reg(EC_HWM_LDN, 0x0081, &val, READ_OP); + val |= 0x60; + ec_read_write_reg(EC_HWM_LDN, 0x0081, &val, WRITE_OP); + } + + ec_read_write_reg(EC_HWM_LDN, 0x00b8, &val, READ_OP); + + if (chassis_type == 4 || chassis_type == 5) { + ec_read_write_reg(EC_HWM_LDN, 0x00a0, &val, READ_OP); + val &= 0xfb; + ec_read_write_reg(EC_HWM_LDN, 0x00a0, &val, WRITE_OP); + ec_read_write_reg(EC_HWM_LDN, 0x00a1, &val, READ_OP); + val &= 0xfb; + ec_read_write_reg(EC_HWM_LDN, 0x00a1, &val, WRITE_OP); + ec_read_write_reg(EC_HWM_LDN, 0x00a2, &val, READ_OP); + val &= 0xfb; + ec_read_write_reg(EC_HWM_LDN, 0x00a2, &val, WRITE_OP); + val = 0x99; + ec_read_write_reg(EC_HWM_LDN, 0x008a, &val, WRITE_OP); + val = 0x47; + ec_read_write_reg(EC_HWM_LDN, 0x008b, &val, WRITE_OP); + val = 0x91; + ec_read_write_reg(EC_HWM_LDN, 0x008c, &val, WRITE_OP); + } + + ec_read_write_reg(EC_HWM_LDN, 0x0049, &val, READ_OP); + val &= 0xf7; + ec_read_write_reg(EC_HWM_LDN, 0x0049, &val, WRITE_OP); + + val = 0x6a; + if (chassis_type != 3) + ec_read_write_reg(EC_HWM_LDN, 0x0059, &val, WRITE_OP); + else + ec_read_write_reg(EC_HWM_LDN, 0x0057, &val, WRITE_OP); + + ec_read_write_reg(EC_HWM_LDN, 0x0041, &val, READ_OP); + val |= 0x40; + ec_read_write_reg(EC_HWM_LDN, 0x0041, &val, WRITE_OP); + + if (chassis_type == 3) { + ec_read_write_reg(EC_HWM_LDN, 0x0049, &val, READ_OP); + val |= 0x04; + } else { + ec_read_write_reg(EC_HWM_LDN, 0x0049, &val, READ_OP); + val |= 0x08; + } + ec_read_write_reg(EC_HWM_LDN, 0x0049, &val, WRITE_OP); + + val = 0x0e; + ec_read_write_reg(EC_HWM_LDN, 0x007b, &val, WRITE_OP); + ec_read_write_reg(EC_HWM_LDN, 0x007c, &val, WRITE_OP); + val = 0x01; + ec_read_write_reg(EC_HWM_LDN, 0x007a, &val, WRITE_OP); +} diff --git a/src/mainboard/dell/optiplex_9010/sch5545_ec.h b/src/mainboard/dell/optiplex_9010/sch5545_ec.h new file mode 100644 index 0000000000..0ca589f9eb --- /dev/null +++ b/src/mainboard/dell/optiplex_9010/sch5545_ec.h @@ -0,0 +1,28 @@ +/* SPDX-License-Identifier: GPL-2.0-only */ + +#include <stdint.h> + +#define READ_OP 0 +#define WRITE_OP 1 + +#define EC_HWM_LDN 1 +#define EC_GPIO_LDN 2 + +/* EC GPIO configuration */ +#define EC_GPIO_PP (0 << 0) +#define EC_GPIO_OD (1 << 0) +#define EC_GPIO_FUNC0 (0 << 4) +#define EC_GPIO_FUNC1 (1 << 4) +#define EC_GPIO_FUNC2 (2 << 4) +#define EC_GPIO_FUNC3 (3 << 4) + +struct ec_val_reg { + uint8_t val; + uint16_t reg; +}; + +uint16_t sch5545_get_ec_fw_version(void); +void sch5545_update_ec_firmware(uint16_t ec_version); +void sch5545_ec_early_init(void); +void sch5545_ec_hwm_early_init(void); +void sch5545_ec_hwm_init(void *unused); diff --git a/src/mainboard/dell/optiplex_9010/sch5545_ec_early.c b/src/mainboard/dell/optiplex_9010/sch5545_ec_early.c new file mode 100644 index 0000000000..70b7de6064 --- /dev/null +++ b/src/mainboard/dell/optiplex_9010/sch5545_ec_early.c @@ -0,0 +1,116 @@ +/* SPDX-License-Identifier: GPL-2.0-only */ + +#include <arch/io.h> +#include <superio/smsc/sch5545/sch5545.h> +#include <superio/smsc/sch5545/sch5545_emi.h> + +#include "sch5545_ec.h" + +static uint16_t emi_bar; + +static const struct ec_val_reg ec_gpio_init_table[] = { + /* + * Probably some early GPIO initialization, setting GPIO functions. + * The LSBs in third column match the GPIO config registers offsets for + * non-default GPIOs. + */ + { EC_GPIO_PP | EC_GPIO_FUNC1, 0x08cc }, /* GP063 (def) / KBDRST# */ + { EC_GPIO_PP | EC_GPIO_FUNC1, 0x08d0 }, /* GP064 (def) / A20M */ + { EC_GPIO_PP | EC_GPIO_FUNC1, 0x089c }, /* GP047 / TXD1 (def) */ + { EC_GPIO_PP | EC_GPIO_FUNC1, 0x0878 }, /* GP036 (def) / SMBCLK1 */ + { EC_GPIO_PP | EC_GPIO_FUNC1, 0x0880 }, /* GP040 (def) / SMBDAT1 */ + { EC_GPIO_OD | EC_GPIO_FUNC1, 0x0884 }, /* GP041 (def) / IO_PME# */ + { EC_GPIO_PP | EC_GPIO_FUNC1, 0x08e4 }, /* GP071 (def) / IO_SMI# */ + { EC_GPIO_PP | EC_GPIO_FUNC1, 0x08e0 }, /* GP070 (def) / SPEAKER */ + { EC_GPIO_PP | EC_GPIO_FUNC1, 0x0848 }, /* GP022 (def) / PWM1 */ + { EC_GPIO_PP | EC_GPIO_FUNC1, 0x084c }, /* GP023 (def) / PWM2 */ + { EC_GPIO_PP | EC_GPIO_FUNC1, 0x0850 }, /* GP024 (def) / PWM3 */ + { EC_GPIO_PP | EC_GPIO_FUNC1, 0x083c }, /* GP017 / TACH1 (def) */ + { EC_GPIO_PP | EC_GPIO_FUNC1, 0x0840 }, /* GP020 / TACH2 (def) */ + { EC_GPIO_PP | EC_GPIO_FUNC1, 0x0844 }, /* GP021 / TACH3 (def) */ + { EC_GPIO_PP | EC_GPIO_FUNC1, 0x0814 }, /* GP005 (def) / PECI_REQ# */ +}; + +static const struct ec_val_reg ec_hwm_early_init_table[] = { + /* Probably some early hardware monitor initialization */ + { 0xff, 0x0005 }, + { 0x30, 0x00f0 }, + { 0x10, 0x00f8 }, + { 0x00, 0x00f9 }, + { 0x00, 0x00fa }, + { 0x00, 0x00fb }, + { 0x00, 0x00ea }, + { 0x00, 0x00eb }, + { 0x7c, 0x00ef }, + { 0x03, 0x006e }, + { 0x51, 0x02d0 }, + { 0x01, 0x02d2 }, + { 0x12, 0x059a }, + { 0x11, 0x059e }, + { 0x14, 0x05a2 }, + { 0x55, 0x05a3 }, + { 0x01, 0x02db }, + { 0x01, 0x0040 }, +}; + +static void ec_read_write_reg_timeout(uint16_t ldn, uint8_t *val, uint16_t reg, + uint8_t rw_bit) +{ + uint16_t timeout = 0; + rw_bit &= 1; + sch5545_emi_ec2h_mailbox_clear(); + sch5545_emi_ec_write16(0x8000, (ldn << 1) | 0x100 | rw_bit); + + sch5545_emi_set_ec_addr(0x8004); + + if (rw_bit) + outb(*val, emi_bar + SCH5545_EMI_EC_DATA); + + outb(reg & 0xff, emi_bar + SCH5545_EMI_EC_DATA + 2); + outb((reg >> 8) & 0xff, emi_bar + SCH5545_EMI_EC_DATA + 3); + sch5545_emi_h2ec_mbox_write(1); + + do { + timeout++; + if ((sch5545_emi_ec2h_mbox_read() & 1) != 0) + break; + } while (timeout < 0xfff); + + sch5545_emi_set_int_src(0x11); + sch5545_emi_h2ec_mbox_write(0xc0); + + if (!rw_bit) + *val = inb(emi_bar + SCH5545_EMI_EC_DATA); +} + +static void ec_init_gpios(void) +{ + unsigned int i; + uint8_t val; + + for (i = 0; i < ARRAY_SIZE(ec_gpio_init_table); i++) { + val = ec_gpio_init_table[i].val; + ec_read_write_reg_timeout(EC_GPIO_LDN, &val, ec_gpio_init_table[i].reg, + WRITE_OP); + } +} + +static void ec_early_hwm_init(void) +{ + unsigned int i; + uint8_t val; + + for (i = 0; i < ARRAY_SIZE(ec_hwm_early_init_table); i++) { + val = ec_hwm_early_init_table[i].val; + ec_read_write_reg_timeout(EC_HWM_LDN, &val, ec_hwm_early_init_table[i].reg, + WRITE_OP); + } +} + +void sch5545_ec_early_init(void) +{ + emi_bar = sch5545_read_emi_bar(0x2e); + + ec_init_gpios(); + ec_early_hwm_init(); +} diff --git a/src/mainboard/dell/optiplex_9010/smihandler.c b/src/mainboard/dell/optiplex_9010/smihandler.c new file mode 100644 index 0000000000..d3c83ef5e7 --- /dev/null +++ b/src/mainboard/dell/optiplex_9010/smihandler.c @@ -0,0 +1,47 @@ +/* SPDX-License-Identifier: GPL-2.0-only */ + +#include <stdint.h> +#include <arch/io.h> +#include <console/console.h> +#include <cpu/x86/smm.h> +#include <superio/smsc/sch5545/sch5545.h> + +void mainboard_smi_gpi(u32 gpi_sts) +{ + printk(BIOS_SPEW, "%s: gpi_sts: %08x\n", __func__, gpi_sts); +} + +int mainboard_smi_apmc(u8 data) +{ + u8 val; + switch (data) { + case APM_CNT_ACPI_ENABLE: + printk(BIOS_SPEW, "%s: APM CNT EN: %02x\n", __func__, data); + /* Enable wake on PS2 */ + val = inb(SCH5545_RUNTIME_REG_BASE + SCH5545_RR_PME_EN1); + val |= (SCH5545_KBD_PME_EN | SCH5545_MOUSE_PME_EN); + outb(val, SCH5545_RUNTIME_REG_BASE + SCH5545_RR_PME_EN1); + /* Clear pending and enable PMEs */ + outb(SCH5545_GLOBAL_PME_STS, SCH5545_RUNTIME_REG_BASE + SCH5545_RR_PME_STS); + outb(SCH5545_GLOBAL_PME_EN, SCH5545_RUNTIME_REG_BASE + SCH5545_RR_PME_EN); + break; + case APM_CNT_ACPI_DISABLE: + printk(BIOS_SPEW, "%s: APM CNT DIS: %02x\n", __func__, data); + /* Disable wake on PS2 */ + val = inb(SCH5545_RUNTIME_REG_BASE + SCH5545_RR_PME_EN1); + val &= ~(SCH5545_KBD_PME_EN | SCH5545_MOUSE_PME_EN); + outb(val, SCH5545_RUNTIME_REG_BASE + SCH5545_RR_PME_EN1); + /* Clear pending and disable PMEs */ + outb(SCH5545_GLOBAL_PME_STS, SCH5545_RUNTIME_REG_BASE + SCH5545_RR_PME_STS); + outb(0, SCH5545_RUNTIME_REG_BASE + SCH5545_RR_PME_EN); + break; + default: + break; + } + return 0; +} + +void mainboard_smi_sleep(u8 slp_typ) +{ + printk(BIOS_SPEW, "%s: SMI sleep: %02x\n", __func__, slp_typ); +} |