diff options
Diffstat (limited to 'src/mainboard')
15 files changed, 562 insertions, 1475 deletions
diff --git a/src/mainboard/google/glados/Kconfig b/src/mainboard/google/glados/Kconfig index d0ff3776e0..5e3545a85c 100644 --- a/src/mainboard/google/glados/Kconfig +++ b/src/mainboard/google/glados/Kconfig @@ -60,9 +60,9 @@ config VARIANT_DIR default "lars" if BOARD_GOOGLE_LARS default "sentry" if BOARD_GOOGLE_SENTRY -config DEVICETREE +config OVERRIDE_DEVICETREE string - default "variants/$(CONFIG_VARIANT_DIR)/devicetree.cb" + default "variants/$(CONFIG_VARIANT_DIR)/overridetree.cb" config MAX_CPUS int diff --git a/src/mainboard/google/glados/variants/lars/devicetree.cb b/src/mainboard/google/glados/devicetree.cb index 35ce9a0294..e9c1cac69c 100644 --- a/src/mainboard/google/glados/variants/lars/devicetree.cb +++ b/src/mainboard/google/glados/devicetree.cb @@ -77,18 +77,6 @@ chip soc/intel/skylake # RP 1 uses SRCCLKREQ1# register "PcieRpClkReqNumber[0]" = "1" - register "usb2_ports[0]" = "USB2_PORT_TYPE_C(OC0)" # Type-C Port 1 - register "usb2_ports[1]" = "USB2_PORT_FLEX(OC_SKIP)" # Camera - register "usb2_ports[2]" = "USB2_PORT_MID(OC_SKIP)" # Bluetooth - register "usb2_ports[4]" = "USB2_PORT_MID(OC2)" # Type-A Port (card) - register "usb2_ports[5]" = "USB2_PORT_MID(OC_SKIP)" # SD - register "usb2_ports[8]" = "USB2_PORT_LONG(OC3)" # Type-A Port (board) - - register "usb3_ports[0]" = "USB3_PORT_DEFAULT(OC0)" # Type-C Port 1 - register "usb3_ports[1]" = "USB3_PORT_DEFAULT(OC_SKIP)" # SD - register "usb3_ports[2]" = "USB3_PORT_DEFAULT(OC2)" # Type-A Port (card) - register "usb3_ports[3]" = "USB3_PORT_DEFAULT(OC3)" # Type-A Port (board) - # Must leave UART0 enabled or SD/eMMC will not work as PCI register "SerialIoDevMode" = "{ [PchSerialIoIndexI2C0] = PchSerialIoPci, @@ -127,23 +115,8 @@ chip soc/intel/skylake device pci 14.0 on end # USB xHCI device pci 14.1 off end # USB xDCI (OTG) device pci 14.2 on end # Thermal Subsystem - device pci 15.0 on - chip drivers/i2c/generic - register "hid" = ""ELAN0001"" - register "desc" = ""ELAN Touchscreen"" - register "irq" = "ACPI_IRQ_EDGE_LOW(GPP_E7_IRQ)" - device i2c 10 on end - end - end # I2C #0 - device pci 15.1 on - chip drivers/i2c/generic - register "hid" = ""ELAN0000"" - register "desc" = ""ELAN Touchpad"" - register "irq" = "ACPI_IRQ_LEVEL_LOW(GPP_B3_IRQ)" - register "wake" = "GPE0_DW0_05" - device i2c 15 on end - end - end # I2C #1 + device pci 15.0 on end # I2C #0 + device pci 15.1 on end # I2C #1 device pci 15.2 off end # I2C #2 device pci 15.3 off end # I2C #3 device pci 16.0 on end # Management Engine Interface 1 @@ -154,30 +127,7 @@ chip soc/intel/skylake device pci 17.0 off end # SATA device pci 19.0 on end # UART #2 device pci 19.1 off end # I2C #5 - device pci 19.2 on - chip drivers/i2c/nau8825 - register "irq" = "ACPI_IRQ_LEVEL_LOW(GPP_F10_IRQ)" - register "jkdet_enable" = "1" - register "jkdet_pull_enable" = "1" - register "jkdet_pull_up" = "1" - register "jkdet_polarity" = "1" # ActiveLow - register "vref_impedance" = "2" # 125kOhm - register "micbias_voltage" = "6" # 2.754 - register "sar_threshold_num" = "4" - register "sar_threshold[0]" = "0x08" - register "sar_threshold[1]" = "0x12" - register "sar_threshold[2]" = "0x26" - register "sar_threshold[3]" = "0x73" - register "sar_hysteresis" = "0" - register "sar_voltage" = "6" - register "sar_compare_time" = "1" # 1us - register "sar_sampling_time" = "1" # 4us - register "short_key_debounce" = "3" # 30ms - register "jack_insert_debounce" = "7" # 512ms - register "jack_eject_debounce" = "0" - device i2c 1a on end - end - end # I2C #4 + device pci 19.2 on end # I2C #4 device pci 1c.0 on chip drivers/intel/wifi register "wake" = "GPE0_DW0_16" @@ -201,7 +151,7 @@ chip soc/intel/skylake device pci 1e.3 off end # GSPI #1 device pci 1e.4 on end # eMMC device pci 1e.5 off end # SDIO - device pci 1e.6 off end # SDCard + device pci 1e.6 off end # SDCard device pci 1f.0 on chip drivers/pc80/tpm device pnp 0c31.0 on end @@ -212,14 +162,7 @@ chip soc/intel/skylake end # LPC Interface device pci 1f.1 on end # P2SB device pci 1f.2 on end # Power Management Controller - device pci 1f.3 on - chip drivers/generic/max98357a - register "hid" = ""MX98357A"" - register "sdmode_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_B2)" - register "sdmode_delay" = "5" - device generic 0 on end - end - end # Intel HDA + device pci 1f.3 on end # Intel HDA device pci 1f.4 on end # SMBus device pci 1f.5 on end # PCH SPI device pci 1f.6 off end # GbE diff --git a/src/mainboard/google/glados/variants/asuka/devicetree.cb b/src/mainboard/google/glados/variants/asuka/devicetree.cb deleted file mode 100644 index 395b5728b7..0000000000 --- a/src/mainboard/google/glados/variants/asuka/devicetree.cb +++ /dev/null @@ -1,227 +0,0 @@ -chip soc/intel/skylake - - register "gpu_pp_up_delay_ms" = "200" - register "gpu_pp_down_delay_ms" = " 50" - register "gpu_pp_cycle_delay_ms" = "500" - register "gpu_pp_backlight_on_delay_ms" = " 1" - register "gpu_pp_backlight_off_delay_ms" = "200" - - register "gpu_pch_backlight_pwm_hz" = "1000" - - # Enable deep Sx states - register "deep_s3_enable_ac" = "0" - register "deep_s3_enable_dc" = "0" - register "deep_s5_enable_ac" = "1" - register "deep_s5_enable_dc" = "1" - register "deep_sx_config" = "DSX_EN_LAN_WAKE_PIN" - - # GPE configuration - # Note that GPE events called out in ASL code rely on this - # route. i.e. If this route changes then the affected GPE - # offset bits also need to be changed. - register "gpe0_dw0" = "GPP_B" - register "gpe0_dw1" = "GPP_D" - register "gpe0_dw2" = "GPP_E" - - # EC host command ranges are in 0x800-0x8ff & 0x200-0x20f - register "gen1_dec" = "0x00fc0801" - register "gen2_dec" = "0x000c0201" - - # Enable "Intel Speed Shift Technology" - register "speed_shift_enable" = "1" - - # Enable DPTF - register "dptf_enable" = "1" - - # FSP Configuration - register "ProbelessTrace" = "0" - register "EnableLan" = "0" - register "EnableSata" = "0" - register "SataSalpSupport" = "0" - register "SataMode" = "0" - register "SataPortsEnable[0]" = "0" - register "EnableAzalia" = "1" - register "DspEnable" = "1" - register "IoBufferOwnership" = "3" - register "EnableTraceHub" = "0" - register "SsicPortEnable" = "0" - register "SmbusEnable" = "1" - register "Cio2Enable" = "0" - register "ScsEmmcEnabled" = "1" - register "ScsEmmcHs400Enabled" = "1" - register "ScsSdCardEnabled" = "0" - register "PttSwitch" = "0" - register "SkipExtGfxScan" = "1" - register "Device4Enable" = "1" - register "HeciEnabled" = "0" - register "SaGv" = "3" - register "PmConfigSlpS3MinAssert" = "2" # 50ms - register "PmConfigSlpS4MinAssert" = "4" # 4s - register "PmConfigSlpSusMinAssert" = "3" # 4s - register "PmConfigSlpAMinAssert" = "3" # 2s - register "PmTimerDisabled" = "1" - - register "pirqa_routing" = "PCH_IRQ11" - register "pirqb_routing" = "PCH_IRQ10" - register "pirqc_routing" = "PCH_IRQ11" - register "pirqd_routing" = "PCH_IRQ11" - register "pirqe_routing" = "PCH_IRQ11" - register "pirqf_routing" = "PCH_IRQ11" - register "pirqg_routing" = "PCH_IRQ11" - register "pirqh_routing" = "PCH_IRQ11" - - # Enable Root port 1 - register "PcieRpEnable[0]" = "1" - # Enable CLKREQ# - register "PcieRpClkReqSupport[0]" = "1" - # RP 1 uses SRCCLKREQ1# - register "PcieRpClkReqNumber[0]" = "1" - - register "usb2_ports[0]" = "USB2_PORT_TYPE_C(OC0)" # Type-C Port 1 - register "usb2_ports[1]" = "USB2_PORT_MID(OC2)" # Card Reader - register "usb2_ports[2]" = "USB2_PORT_MID(OC_SKIP)" # Bluetooth - register "usb2_ports[4]" = "USB2_PORT_MID(OC2)" # Type-A Port (board) - register "usb2_ports[6]" = "USB2_PORT_FLEX(OC_SKIP)" # Camera - register "usb2_ports[7]" = "USB2_PORT_MID(OC_SKIP)" # PIC MCU - register "usb2_ports[8]" = "USB2_PORT_LONG(OC3)" # Type-A Port (board) - - register "usb3_ports[0]" = "USB3_PORT_DEFAULT(OC0)" # Type-C Port 1 - register "usb3_ports[1]" = "USB3_PORT_DEFAULT(OC_SKIP)" # Card Reader - register "usb3_ports[2]" = "USB3_PORT_DEFAULT(OC2)" # Type-A Port (board) - register "usb3_ports[3]" = "USB3_PORT_DEFAULT(OC3)" # Type-A Port (board) - - # Must leave UART0 enabled or SD/eMMC will not work as PCI - register "SerialIoDevMode" = "{ - [PchSerialIoIndexI2C0] = PchSerialIoPci, - [PchSerialIoIndexI2C1] = PchSerialIoPci, - [PchSerialIoIndexI2C2] = PchSerialIoDisabled, - [PchSerialIoIndexI2C3] = PchSerialIoDisabled, - [PchSerialIoIndexI2C4] = PchSerialIoPci, - [PchSerialIoIndexI2C5] = PchSerialIoDisabled, - [PchSerialIoIndexSpi0] = PchSerialIoDisabled, - [PchSerialIoIndexSpi1] = PchSerialIoDisabled, - [PchSerialIoIndexUart0] = PchSerialIoPci, - [PchSerialIoIndexUart1] = PchSerialIoDisabled, - [PchSerialIoIndexUart2] = PchSerialIoSkipInit, - }" - - # I2C4 is 1.8V - register "i2c_voltage[4]" = "I2C_VOLTAGE_1V8" - - # PL2 override 25W - register "tdp_pl2_override" = "25" - - # Send an extra VR mailbox command for the PS4 exit issue - register "SendVrMbxCmd" = "2" - - # Lock Down - register "common_soc_config" = "{ - .chipset_lockdown = CHIPSET_LOCKDOWN_COREBOOT, - }" - - device cpu_cluster 0 on - device lapic 0 on end - end - device domain 0 on - device pci 00.0 on end # Host Bridge - device pci 02.0 on end # Integrated Graphics Device - device pci 14.0 on end # USB xHCI - device pci 14.1 off end # USB xDCI (OTG) - device pci 14.2 on end # Thermal Subsystem - device pci 15.0 on - chip drivers/i2c/generic - register "hid" = ""ELAN0001"" - register "desc" = ""ELAN Touchscreen"" - register "irq" = "ACPI_IRQ_EDGE_LOW(GPP_E7_IRQ)" - device i2c 10 on end - end - end # I2C #0 - device pci 15.1 on - chip drivers/i2c/generic - register "hid" = ""ELAN0000"" - register "desc" = ""ELAN Touchpad"" - register "irq" = "ACPI_IRQ_LEVEL_LOW(GPP_B3_IRQ)" - register "wake" = "GPE0_DW0_05" - device i2c 15 on end - end - end # I2C #1 - device pci 15.2 off end # I2C #2 - device pci 15.3 off end # I2C #3 - device pci 16.0 on end # Management Engine Interface 1 - device pci 16.1 off end # Management Engine Interface 2 - device pci 16.2 off end # Management Engine IDE-R - device pci 16.3 off end # Management Engine KT Redirection - device pci 16.4 off end # Management Engine Interface 3 - device pci 17.0 off end # SATA - device pci 19.0 on end # UART #2 - device pci 19.1 off end # I2C #5 - device pci 19.2 on - chip drivers/i2c/nau8825 - register "irq" = "ACPI_IRQ_LEVEL_LOW(GPP_F10_IRQ)" - register "jkdet_enable" = "1" - register "jkdet_pull_enable" = "0" # R389 - register "jkdet_polarity" = "1" # ActiveLow - register "vref_impedance" = "2" # 125kOhm - register "micbias_voltage" = "6" # 2.754 - register "sar_threshold_num" = "4" - register "sar_threshold[0]" = "0x08" - register "sar_threshold[1]" = "0x12" - register "sar_threshold[2]" = "0x26" - register "sar_threshold[3]" = "0x73" - register "sar_hysteresis" = "0" - register "sar_voltage" = "6" - register "sar_compare_time" = "1" # 1us - register "sar_sampling_time" = "1" # 4us - register "short_key_debounce" = "3" # 30ms - register "jack_insert_debounce" = "7" # 512ms - register "jack_eject_debounce" = "0" - device i2c 1a on end - end - end # I2C #4 - device pci 1c.0 on - chip drivers/intel/wifi - register "wake" = "GPE0_DW0_16" - device pci 00.0 on end - end - end # PCI Express Port 1 - device pci 1c.1 off end # PCI Express Port 2 - device pci 1c.2 off end # PCI Express Port 3 - device pci 1c.3 off end # PCI Express Port 4 - device pci 1c.4 off end # PCI Express Port 5 - device pci 1c.5 off end # PCI Express Port 6 - device pci 1c.6 off end # PCI Express Port 7 - device pci 1c.7 off end # PCI Express Port 8 - device pci 1d.0 off end # PCI Express Port 9 - device pci 1d.1 off end # PCI Express Port 10 - device pci 1d.2 off end # PCI Express Port 11 - device pci 1d.3 off end # PCI Express Port 12 - device pci 1e.0 on end # UART #0 - device pci 1e.1 off end # UART #1 - device pci 1e.2 off end # GSPI #0 - device pci 1e.3 off end # GSPI #1 - device pci 1e.4 on end # eMMC - device pci 1e.5 off end # SDIO - device pci 1e.6 off end # SDCard - device pci 1f.0 on - chip drivers/pc80/tpm - device pnp 0c31.0 on end - end - chip ec/google/chromeec - device pnp 0c09.0 on end - end - end # LPC Interface - device pci 1f.1 on end # P2SB - device pci 1f.2 on end # Power Management Controller - device pci 1f.3 on - chip drivers/generic/max98357a - register "hid" = ""MX98357A"" - register "sdmode_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_E3)" - register "sdmode_delay" = "5" - device generic 0 on end - end - end # Intel HDA - device pci 1f.4 on end # SMBus - device pci 1f.5 on end # PCH SPI - device pci 1f.6 off end # GbE - end -end diff --git a/src/mainboard/google/glados/variants/asuka/overridetree.cb b/src/mainboard/google/glados/variants/asuka/overridetree.cb new file mode 100644 index 0000000000..4be1fc6ae3 --- /dev/null +++ b/src/mainboard/google/glados/variants/asuka/overridetree.cb @@ -0,0 +1,66 @@ +chip soc/intel/skylake + + register "usb2_ports[0]" = "USB2_PORT_TYPE_C(OC0)" # Type-C Port 1 + register "usb2_ports[1]" = "USB2_PORT_MID(OC2)" # Card Reader + register "usb2_ports[2]" = "USB2_PORT_MID(OC_SKIP)" # Bluetooth + register "usb2_ports[4]" = "USB2_PORT_MID(OC2)" # Type-A Port (board) + register "usb2_ports[6]" = "USB2_PORT_FLEX(OC_SKIP)" # Camera + register "usb2_ports[7]" = "USB2_PORT_MID(OC_SKIP)" # PIC MCU + register "usb2_ports[8]" = "USB2_PORT_LONG(OC3)" # Type-A Port (board) + + register "usb3_ports[0]" = "USB3_PORT_DEFAULT(OC0)" # Type-C Port 1 + register "usb3_ports[1]" = "USB3_PORT_DEFAULT(OC_SKIP)" # Card Reader + register "usb3_ports[2]" = "USB3_PORT_DEFAULT(OC2)" # Type-A Port (board) + register "usb3_ports[3]" = "USB3_PORT_DEFAULT(OC3)" # Type-A Port (board) + + device domain 0 on + device pci 15.0 on + chip drivers/i2c/generic + register "hid" = ""ELAN0001"" + register "desc" = ""ELAN Touchscreen"" + register "irq" = "ACPI_IRQ_EDGE_LOW(GPP_E7_IRQ)" + device i2c 10 on end + end + end # I2C #0 + device pci 15.1 on + chip drivers/i2c/generic + register "hid" = ""ELAN0000"" + register "desc" = ""ELAN Touchpad"" + register "irq" = "ACPI_IRQ_LEVEL_LOW(GPP_B3_IRQ)" + register "wake" = "GPE0_DW0_05" + device i2c 15 on end + end + end # I2C #1 + device pci 19.2 on + chip drivers/i2c/nau8825 + register "irq" = "ACPI_IRQ_LEVEL_LOW(GPP_F10_IRQ)" + register "jkdet_enable" = "1" + register "jkdet_pull_enable" = "0" # R389 + register "jkdet_polarity" = "1" # ActiveLow + register "vref_impedance" = "2" # 125kOhm + register "micbias_voltage" = "6" # 2.754 + register "sar_threshold_num" = "4" + register "sar_threshold[0]" = "0x08" + register "sar_threshold[1]" = "0x12" + register "sar_threshold[2]" = "0x26" + register "sar_threshold[3]" = "0x73" + register "sar_hysteresis" = "0" + register "sar_voltage" = "6" + register "sar_compare_time" = "1" # 1us + register "sar_sampling_time" = "1" # 4us + register "short_key_debounce" = "3" # 30ms + register "jack_insert_debounce" = "7" # 512ms + register "jack_eject_debounce" = "0" + device i2c 1a on end + end + end # I2C #4 + device pci 1f.3 on + chip drivers/generic/max98357a + register "hid" = ""MX98357A"" + register "sdmode_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_E3)" + register "sdmode_delay" = "5" + device generic 0 on end + end + end # Intel HDA + end +end diff --git a/src/mainboard/google/glados/variants/caroline/devicetree.cb b/src/mainboard/google/glados/variants/caroline/devicetree.cb deleted file mode 100644 index 3e733d6b1c..0000000000 --- a/src/mainboard/google/glados/variants/caroline/devicetree.cb +++ /dev/null @@ -1,241 +0,0 @@ -chip soc/intel/skylake - - register "gpu_pp_up_delay_ms" = "200" - register "gpu_pp_down_delay_ms" = " 50" - register "gpu_pp_cycle_delay_ms" = "500" - register "gpu_pp_backlight_on_delay_ms" = " 1" - register "gpu_pp_backlight_off_delay_ms" = "200" - - register "gpu_pch_backlight_pwm_hz" = "1000" - - # Enable deep Sx states - register "deep_s3_enable_ac" = "0" - register "deep_s3_enable_dc" = "0" - register "deep_s5_enable_ac" = "1" - register "deep_s5_enable_dc" = "1" - register "deep_sx_config" = "DSX_EN_LAN_WAKE_PIN" - - # GPE configuration - # Note that GPE events called out in ASL code rely on this - # route. i.e. If this route changes then the affected GPE - # offset bits also need to be changed. - register "gpe0_dw0" = "GPP_B" - register "gpe0_dw1" = "GPP_D" - register "gpe0_dw2" = "GPP_E" - - # EC host command ranges are in 0x800-0x8ff & 0x200-0x20f - register "gen1_dec" = "0x00fc0801" - register "gen2_dec" = "0x000c0201" - - # Enable "Intel Speed Shift Technology" - register "speed_shift_enable" = "1" - - # Enable DPTF - register "dptf_enable" = "1" - - # FSP Configuration - register "ProbelessTrace" = "0" - register "EnableLan" = "0" - register "EnableSata" = "0" - register "SataSalpSupport" = "0" - register "SataMode" = "0" - register "SataPortsEnable[0]" = "0" - register "EnableAzalia" = "1" - register "DspEnable" = "1" - register "IoBufferOwnership" = "3" - register "EnableTraceHub" = "0" - register "SsicPortEnable" = "0" - register "SmbusEnable" = "1" - register "Cio2Enable" = "0" - register "ScsEmmcEnabled" = "1" - register "ScsEmmcHs400Enabled" = "1" - register "ScsSdCardEnabled" = "2" - register "PttSwitch" = "0" - register "SkipExtGfxScan" = "1" - register "Device4Enable" = "1" - register "HeciEnabled" = "0" - register "SaGv" = "3" - register "PmConfigSlpS3MinAssert" = "2" # 50ms - register "PmConfigSlpS4MinAssert" = "1" # 1s - register "PmConfigSlpSusMinAssert" = "1" # 500ms - register "PmConfigSlpAMinAssert" = "3" # 2s - register "PmTimerDisabled" = "1" - - register "pirqa_routing" = "PCH_IRQ11" - register "pirqb_routing" = "PCH_IRQ10" - register "pirqc_routing" = "PCH_IRQ11" - register "pirqd_routing" = "PCH_IRQ11" - register "pirqe_routing" = "PCH_IRQ11" - register "pirqf_routing" = "PCH_IRQ11" - register "pirqg_routing" = "PCH_IRQ11" - register "pirqh_routing" = "PCH_IRQ11" - - # VR Slew rate setting for improving audible noise - register "AcousticNoiseMitigation" = "1" - register "SlowSlewRateForIa" = "3" # Fast/16 - register "SlowSlewRateForGt" = "3" # Fast/16 - register "SlowSlewRateForSa" = "0" # Fast/2 - register "FastPkgCRampDisable" = "0" - - # Enable Root port 1 - register "PcieRpEnable[0]" = "1" - # Enable CLKREQ# - register "PcieRpClkReqSupport[0]" = "1" - # RP 1 uses SRCCLKREQ1# - register "PcieRpClkReqNumber[0]" = "1" - - register "usb2_ports[0]" = "USB2_PORT_MID(OC_SKIP)" # Type-C Port (main) - register "usb2_ports[1]" = "USB2_PORT_MAX(OC_SKIP)" # Type-C Port (sub) - register "usb2_ports[2]" = "USB2_PORT_MID(OC_SKIP)" # Bluetooth - register "usb2_ports[4]" = "USB2_PORT_EMPTY" # Empty - register "usb2_ports[6]" = "USB2_PORT_FLEX(OC_SKIP)" # Camera - register "usb2_ports[8]" = "USB2_PORT_EMPTY" # Empty - - register "usb3_ports[0]" = "USB3_PORT_DEFAULT(OC_SKIP)" # Type-C Port (main) - register "usb3_ports[1]" = "USB3_PORT_DEFAULT(OC_SKIP)" # Type-C Port (sub) - register "usb3_ports[2]" = "USB3_PORT_EMPTY" # Empty - register "usb3_ports[3]" = "USB3_PORT_EMPTY" # Empty - - # Must leave UART0 enabled or SD/eMMC will not work as PCI - register "SerialIoDevMode" = "{ - [PchSerialIoIndexI2C0] = PchSerialIoPci, - [PchSerialIoIndexI2C1] = PchSerialIoPci, - [PchSerialIoIndexI2C2] = PchSerialIoDisabled, - [PchSerialIoIndexI2C3] = PchSerialIoDisabled, - [PchSerialIoIndexI2C4] = PchSerialIoPci, - [PchSerialIoIndexI2C5] = PchSerialIoDisabled, - [PchSerialIoIndexSpi0] = PchSerialIoDisabled, - [PchSerialIoIndexSpi1] = PchSerialIoDisabled, - [PchSerialIoIndexUart0] = PchSerialIoPci, - [PchSerialIoIndexUart1] = PchSerialIoDisabled, - [PchSerialIoIndexUart2] = PchSerialIoSkipInit, - }" - - # I2C4 is 1.8V - register "i2c_voltage[4]" = "I2C_VOLTAGE_1V8" - - # PL2 override 15W - register "tdp_pl2_override" = "15" - - # Send an extra VR mailbox command for the supported MPS IMVP8 model - register "SendVrMbxCmd" = "1" - - # TCC of 90C - register "tcc_offset" = "10" - - # Lock Down - register "common_soc_config" = "{ - .chipset_lockdown = CHIPSET_LOCKDOWN_COREBOOT, - }" - - device cpu_cluster 0 on - device lapic 0 on end - end - device domain 0 on - device pci 00.0 on end # Host Bridge - device pci 02.0 on end # Integrated Graphics Device - device pci 14.0 on end # USB xHCI - device pci 14.1 off end # USB xDCI (OTG) - device pci 14.2 on end # Thermal Subsystem - device pci 15.0 on - chip drivers/i2c/generic - register "hid" = ""ATML0001"" - register "desc" = ""Atmel Touchscreen"" - register "irq" = "ACPI_IRQ_EDGE_LOW(GPP_E7_IRQ)" - device i2c 4b on end - end - end # I2C #0 - device pci 15.1 on - chip drivers/i2c/generic - register "hid" = ""ATML0000"" - register "desc" = ""Atmel Touchpad"" - register "irq" = "ACPI_IRQ_LEVEL_LOW(GPP_B3_IRQ)" - register "wake" = "GPE0_DW0_05" - device i2c 4a on end - end - end # I2C #1 - device pci 15.2 off end # I2C #2 - device pci 15.3 off end # I2C #3 - device pci 16.0 on end # Management Engine Interface 1 - device pci 16.1 off end # Management Engine Interface 2 - device pci 16.2 off end # Management Engine IDE-R - device pci 16.3 off end # Management Engine KT Redirection - device pci 16.4 off end # Management Engine Interface 3 - device pci 17.0 off end # SATA - device pci 19.0 on end # UART #2 - device pci 19.1 off end # I2C #5 - device pci 19.2 on - chip drivers/i2c/nau8825 - register "irq" = "ACPI_IRQ_LEVEL_LOW(GPP_F10_IRQ)" - register "jkdet_enable" = "1" - register "jkdet_pull_enable" = "0" # R389 - register "jkdet_polarity" = "1" # ActiveLow - register "vref_impedance" = "2" # 125kOhm - register "micbias_voltage" = "6" # 2.754 - register "sar_threshold_num" = "4" - register "sar_threshold[0]" = "0x0c" - register "sar_threshold[1]" = "0x1c" - register "sar_threshold[2]" = "0x38" - register "sar_threshold[3]" = "0x60" - register "sar_hysteresis" = "1" - register "sar_voltage" = "0" # VDDA - register "sar_compare_time" = "0" # 500ns - register "sar_sampling_time" = "0" # 2us - register "short_key_debounce" = "2" # 100ms - register "jack_insert_debounce" = "4" # 64ms - register "jack_eject_debounce" = "4" # 64ms - device i2c 1a on end - end - chip drivers/i2c/generic - register "hid" = ""INT343B"" - register "desc" = ""SSM4567 Left Speaker Amp"" - register "uid" = "0" - device i2c 34 on end - end - chip drivers/i2c/generic - register "hid" = ""INT343B"" - register "desc" = ""SSM4567 Right Speaker Amp"" - register "uid" = "1" - device i2c 35 on end - end - end # I2C #4 - device pci 1c.0 on - chip drivers/intel/wifi - register "wake" = "GPE0_DW0_16" - device pci 00.0 on end - end - end # PCI Express Port 1 - device pci 1c.1 off end # PCI Express Port 2 - device pci 1c.2 off end # PCI Express Port 3 - device pci 1c.3 off end # PCI Express Port 4 - device pci 1c.4 off end # PCI Express Port 5 - device pci 1c.5 off end # PCI Express Port 6 - device pci 1c.6 off end # PCI Express Port 7 - device pci 1c.7 off end # PCI Express Port 8 - device pci 1d.0 off end # PCI Express Port 9 - device pci 1d.1 off end # PCI Express Port 10 - device pci 1d.2 off end # PCI Express Port 11 - device pci 1d.3 off end # PCI Express Port 12 - device pci 1e.0 on end # UART #0 - device pci 1e.1 off end # UART #1 - device pci 1e.2 off end # GSPI #0 - device pci 1e.3 off end # GSPI #1 - device pci 1e.4 on end # eMMC - device pci 1e.5 off end # SDIO - device pci 1e.6 on end # SDCard - device pci 1f.0 on - chip drivers/pc80/tpm - device pnp 0c31.0 on end - end - chip ec/google/chromeec - device pnp 0c09.0 on end - end - end # LPC Interface - device pci 1f.1 on end # P2SB - device pci 1f.2 on end # Power Management Controller - device pci 1f.3 on end # Intel HDA - device pci 1f.4 on end # SMBus - device pci 1f.5 on end # PCH SPI - device pci 1f.6 off end # GbE - end -end diff --git a/src/mainboard/google/glados/variants/caroline/overridetree.cb b/src/mainboard/google/glados/variants/caroline/overridetree.cb new file mode 100644 index 0000000000..ce364801ca --- /dev/null +++ b/src/mainboard/google/glados/variants/caroline/overridetree.cb @@ -0,0 +1,91 @@ +chip soc/intel/skylake + + register "ScsSdCardEnabled" = "2" + + register "PmConfigSlpS4MinAssert" = "1" # 1s + register "PmConfigSlpSusMinAssert" = "1" # 500ms + + # VR Slew rate setting for improving audible noise + register "AcousticNoiseMitigation" = "1" + register "SlowSlewRateForIa" = "3" # Fast/16 + register "SlowSlewRateForGt" = "3" # Fast/16 + register "SlowSlewRateForSa" = "0" # Fast/2 + register "FastPkgCRampDisable" = "0" + + register "usb2_ports[0]" = "USB2_PORT_MID(OC_SKIP)" # Type-C Port (main) + register "usb2_ports[1]" = "USB2_PORT_MAX(OC_SKIP)" # Type-C Port (sub) + register "usb2_ports[2]" = "USB2_PORT_MID(OC_SKIP)" # Bluetooth + register "usb2_ports[4]" = "USB2_PORT_EMPTY" # Empty + register "usb2_ports[6]" = "USB2_PORT_FLEX(OC_SKIP)" # Camera + register "usb2_ports[8]" = "USB2_PORT_EMPTY" # Empty + + register "usb3_ports[0]" = "USB3_PORT_DEFAULT(OC_SKIP)" # Type-C Port (main) + register "usb3_ports[1]" = "USB3_PORT_DEFAULT(OC_SKIP)" # Type-C Port (sub) + register "usb3_ports[2]" = "USB3_PORT_EMPTY" # Empty + register "usb3_ports[3]" = "USB3_PORT_EMPTY" # Empty + + # PL2 override 15W + register "tdp_pl2_override" = "15" + + # Send an extra VR mailbox command for the supported MPS IMVP8 model + register "SendVrMbxCmd" = "1" + + # TCC of 90C + register "tcc_offset" = "10" + + device domain 0 on + device pci 15.0 on + chip drivers/i2c/generic + register "hid" = ""ATML0001"" + register "desc" = ""Atmel Touchscreen"" + register "irq" = "ACPI_IRQ_EDGE_LOW(GPP_E7_IRQ)" + device i2c 4b on end + end + end # I2C #0 + device pci 15.1 on + chip drivers/i2c/generic + register "hid" = ""ATML0000"" + register "desc" = ""Atmel Touchpad"" + register "irq" = "ACPI_IRQ_LEVEL_LOW(GPP_B3_IRQ)" + register "wake" = "GPE0_DW0_05" + device i2c 4a on end + end + end # I2C #1 + device pci 19.2 on + chip drivers/i2c/nau8825 + register "irq" = "ACPI_IRQ_LEVEL_LOW(GPP_F10_IRQ)" + register "jkdet_enable" = "1" + register "jkdet_pull_enable" = "0" # R389 + register "jkdet_polarity" = "1" # ActiveLow + register "vref_impedance" = "2" # 125kOhm + register "micbias_voltage" = "6" # 2.754 + register "sar_threshold_num" = "4" + register "sar_threshold[0]" = "0x0c" + register "sar_threshold[1]" = "0x1c" + register "sar_threshold[2]" = "0x38" + register "sar_threshold[3]" = "0x60" + register "sar_hysteresis" = "1" + register "sar_voltage" = "0" # VDDA + register "sar_compare_time" = "0" # 500ns + register "sar_sampling_time" = "0" # 2us + register "short_key_debounce" = "2" # 100ms + register "jack_insert_debounce" = "4" # 64ms + register "jack_eject_debounce" = "4" # 64ms + device i2c 1a on end + end + chip drivers/i2c/generic + register "hid" = ""INT343B"" + register "desc" = ""SSM4567 Left Speaker Amp"" + register "uid" = "0" + device i2c 34 on end + end + chip drivers/i2c/generic + register "hid" = ""INT343B"" + register "desc" = ""SSM4567 Right Speaker Amp"" + register "uid" = "1" + device i2c 35 on end + end + end # I2C #4 + device pci 1e.6 on end # SDCard + end +end diff --git a/src/mainboard/google/glados/variants/cave/devicetree.cb b/src/mainboard/google/glados/variants/cave/devicetree.cb deleted file mode 100644 index ccc2302a58..0000000000 --- a/src/mainboard/google/glados/variants/cave/devicetree.cb +++ /dev/null @@ -1,232 +0,0 @@ -chip soc/intel/skylake - - register "gpu_pp_up_delay_ms" = "200" - register "gpu_pp_down_delay_ms" = " 50" - register "gpu_pp_cycle_delay_ms" = "500" - register "gpu_pp_backlight_on_delay_ms" = " 1" - register "gpu_pp_backlight_off_delay_ms" = "200" - - register "gpu_pch_backlight_pwm_hz" = "1000" - - # Enable deep Sx states - register "deep_s3_enable_ac" = "0" - register "deep_s3_enable_dc" = "0" - register "deep_s5_enable_ac" = "1" - register "deep_s5_enable_dc" = "1" - register "deep_sx_config" = "DSX_EN_LAN_WAKE_PIN" - - # GPE configuration - # Note that GPE events called out in ASL code rely on this - # route. i.e. If this route changes then the affected GPE - # offset bits also need to be changed. - register "gpe0_dw0" = "GPP_B" - register "gpe0_dw1" = "GPP_D" - register "gpe0_dw2" = "GPP_E" - - # EC host command ranges are in 0x800-0x8ff & 0x200-0x20f - register "gen1_dec" = "0x00fc0801" - register "gen2_dec" = "0x000c0201" - - # Enable "Intel Speed Shift Technology" - register "speed_shift_enable" = "1" - - # Enable DPTF - register "dptf_enable" = "1" - - # FSP Configuration - register "ProbelessTrace" = "0" - register "EnableLan" = "0" - register "EnableSata" = "0" - register "SataSalpSupport" = "0" - register "SataMode" = "0" - register "SataPortsEnable[0]" = "0" - register "EnableAzalia" = "1" - register "DspEnable" = "1" - register "IoBufferOwnership" = "3" - register "EnableTraceHub" = "0" - register "SsicPortEnable" = "0" - register "SmbusEnable" = "1" - register "Cio2Enable" = "0" - register "ScsEmmcEnabled" = "1" - register "ScsEmmcHs400Enabled" = "1" - register "ScsSdCardEnabled" = "2" - register "PttSwitch" = "0" - register "SkipExtGfxScan" = "1" - register "Device4Enable" = "1" - register "HeciEnabled" = "0" - register "SaGv" = "3" - register "PmConfigSlpS3MinAssert" = "2" # 50ms - register "PmConfigSlpS4MinAssert" = "1" # 1s - register "PmConfigSlpSusMinAssert" = "1" # 500ms - register "PmConfigSlpAMinAssert" = "3" # 2s - register "PmTimerDisabled" = "1" - - register "pirqa_routing" = "PCH_IRQ11" - register "pirqb_routing" = "PCH_IRQ10" - register "pirqc_routing" = "PCH_IRQ11" - register "pirqd_routing" = "PCH_IRQ11" - register "pirqe_routing" = "PCH_IRQ11" - register "pirqf_routing" = "PCH_IRQ11" - register "pirqg_routing" = "PCH_IRQ11" - register "pirqh_routing" = "PCH_IRQ11" - - # Enable Root port 1 - register "PcieRpEnable[0]" = "1" - # Enable CLKREQ# - register "PcieRpClkReqSupport[0]" = "1" - # RP 1 uses SRCCLKREQ1# - register "PcieRpClkReqNumber[0]" = "1" - - register "usb2_ports[0]" = "USB2_PORT_TYPE_C(OC_SKIP)" # Type-C Port (board) - register "usb2_ports[1]" = "USB2_PORT_MAX(OC_SKIP)" # Type-C Port (flex) - register "usb2_ports[2]" = "USB2_PORT_MID(OC_SKIP)" # Bluetooth - register "usb2_ports[4]" = "USB2_PORT_EMPTY" # Type-A Port 1 - register "usb2_ports[6]" = "USB2_PORT_FLEX(OC_SKIP)" # Camera - register "usb2_ports[8]" = "USB2_PORT_EMPTY" # Type-A Port 2 - - register "usb3_ports[0]" = "USB3_PORT_DEFAULT(OC_SKIP)" # Type-C Port (board) - register "usb3_ports[1]" = "USB3_PORT_DEFAULT(OC_SKIP)" # Type-C Port (flex) - register "usb3_ports[2]" = "USB3_PORT_EMPTY" # Type-A Port 1 - register "usb3_ports[3]" = "USB3_PORT_EMPTY" # Type-A Port 2 - - # Must leave UART0 enabled or SD/eMMC will not work as PCI - register "SerialIoDevMode" = "{ - [PchSerialIoIndexI2C0] = PchSerialIoPci, - [PchSerialIoIndexI2C1] = PchSerialIoPci, - [PchSerialIoIndexI2C2] = PchSerialIoDisabled, - [PchSerialIoIndexI2C3] = PchSerialIoDisabled, - [PchSerialIoIndexI2C4] = PchSerialIoPci, - [PchSerialIoIndexI2C5] = PchSerialIoDisabled, - [PchSerialIoIndexSpi0] = PchSerialIoDisabled, - [PchSerialIoIndexSpi1] = PchSerialIoDisabled, - [PchSerialIoIndexUart0] = PchSerialIoPci, - [PchSerialIoIndexUart1] = PchSerialIoDisabled, - [PchSerialIoIndexUart2] = PchSerialIoSkipInit, - }" - - # I2C4 is 1.8V - register "i2c_voltage[4]" = "I2C_VOLTAGE_1V8" - - # PL2 override 15W - register "tdp_pl2_override" = "15" - - # Send an extra VR mailbox command for the supported MPS IMVP8 model - register "SendVrMbxCmd" = "1" - - # TCC of 90C - register "tcc_offset" = "10" - - # Use default SD card detect GPIO configuration - register "sdcard_cd_gpio_default" = "GPP_A7" - - # Lock Down - register "common_soc_config" = "{ - .chipset_lockdown = CHIPSET_LOCKDOWN_COREBOOT, - }" - - device cpu_cluster 0 on - device lapic 0 on end - end - device domain 0 on - device pci 00.0 on end # Host Bridge - device pci 02.0 on end # Integrated Graphics Device - device pci 14.0 on end # USB xHCI - device pci 14.1 off end # USB xDCI (OTG) - device pci 14.2 on end # Thermal Subsystem - device pci 15.0 on - chip drivers/i2c/generic - register "hid" = ""ELAN0001"" - register "desc" = ""ELAN Touchscreen"" - register "irq" = "ACPI_IRQ_EDGE_LOW(GPP_E7_IRQ)" - device i2c 10 on end - end - end # I2C #0 - device pci 15.1 on - chip drivers/i2c/generic - register "hid" = ""ELAN0000"" - register "desc" = ""ELAN Touchpad"" - register "irq" = "ACPI_IRQ_LEVEL_LOW(GPP_B3_IRQ)" - register "wake" = "GPE0_DW0_05" - device i2c 15 on end - end - end # I2C #1 - device pci 15.2 off end # I2C #2 - device pci 15.3 off end # I2C #3 - device pci 16.0 on end # Management Engine Interface 1 - device pci 16.1 off end # Management Engine Interface 2 - device pci 16.2 off end # Management Engine IDE-R - device pci 16.3 off end # Management Engine KT Redirection - device pci 16.4 off end # Management Engine Interface 3 - device pci 17.0 off end # SATA - device pci 19.0 on end # UART #2 - device pci 19.1 off end # I2C #5 - device pci 19.2 on - chip drivers/i2c/nau8825 - register "irq" = "ACPI_IRQ_LEVEL_LOW(GPP_F10_IRQ)" - register "jkdet_enable" = "1" - register "jkdet_pull_enable" = "0" # R389 - register "jkdet_polarity" = "1" # ActiveLow - register "vref_impedance" = "2" # 125kOhm - register "micbias_voltage" = "6" # 2.754 - register "sar_threshold_num" = "4" - register "sar_threshold[0]" = "0x0c" - register "sar_threshold[1]" = "0x1e" - register "sar_threshold[2]" = "0x38" - register "sar_threshold[3]" = "0x60" - register "sar_hysteresis" = "1" - register "sar_voltage" = "0" # VDDA - register "sar_compare_time" = "0" # 500ns - register "sar_sampling_time" = "0" # 2us - register "short_key_debounce" = "2" # 100ms - register "jack_insert_debounce" = "7" # 512ms - register "jack_eject_debounce" = "7" # 512ms - device i2c 1a on end - end - end # I2C #4 - device pci 1c.0 on - chip drivers/intel/wifi - register "wake" = "GPE0_DW0_16" - device pci 00.0 on end - end - end # PCI Express Port 1 - device pci 1c.1 off end # PCI Express Port 2 - device pci 1c.2 off end # PCI Express Port 3 - device pci 1c.3 off end # PCI Express Port 4 - device pci 1c.4 off end # PCI Express Port 5 - device pci 1c.5 off end # PCI Express Port 6 - device pci 1c.6 off end # PCI Express Port 7 - device pci 1c.7 off end # PCI Express Port 8 - device pci 1d.0 off end # PCI Express Port 9 - device pci 1d.1 off end # PCI Express Port 10 - device pci 1d.2 off end # PCI Express Port 11 - device pci 1d.3 off end # PCI Express Port 12 - device pci 1e.0 on end # UART #0 - device pci 1e.1 off end # UART #1 - device pci 1e.2 off end # GSPI #0 - device pci 1e.3 off end # GSPI #1 - device pci 1e.4 on end # eMMC - device pci 1e.5 off end # SDIO - device pci 1e.6 on end # SDCard - device pci 1f.0 on - chip drivers/pc80/tpm - device pnp 0c31.0 on end - end - chip ec/google/chromeec - device pnp 0c09.0 on end - end - end # LPC Interface - device pci 1f.1 on end # P2SB - device pci 1f.2 on end # Power Management Controller - device pci 1f.3 on - chip drivers/generic/max98357a - register "hid" = ""MX98357A"" - register "sdmode_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_E3)" - register "sdmode_delay" = "5" - device generic 0 on end - end - end # Intel HDA - device pci 1f.4 on end # SMBus - device pci 1f.5 on end # PCH SPI - device pci 1f.6 off end # GbE - end -end diff --git a/src/mainboard/google/glados/variants/cave/overridetree.cb b/src/mainboard/google/glados/variants/cave/overridetree.cb new file mode 100644 index 0000000000..ae32b3dabf --- /dev/null +++ b/src/mainboard/google/glados/variants/cave/overridetree.cb @@ -0,0 +1,83 @@ +chip soc/intel/skylake + + register "ScsSdCardEnabled" = "2" + + register "PmConfigSlpS4MinAssert" = "1" # 1s + register "PmConfigSlpSusMinAssert" = "1" # 500ms + + register "usb2_ports[0]" = "USB2_PORT_TYPE_C(OC_SKIP)" # Type-C Port (board) + register "usb2_ports[1]" = "USB2_PORT_MAX(OC_SKIP)" # Type-C Port (flex) + register "usb2_ports[2]" = "USB2_PORT_MID(OC_SKIP)" # Bluetooth + register "usb2_ports[4]" = "USB2_PORT_EMPTY" # Type-A Port 1 + register "usb2_ports[6]" = "USB2_PORT_FLEX(OC_SKIP)" # Camera + register "usb2_ports[8]" = "USB2_PORT_EMPTY" # Type-A Port 2 + + register "usb3_ports[0]" = "USB3_PORT_DEFAULT(OC_SKIP)" # Type-C Port (board) + register "usb3_ports[1]" = "USB3_PORT_DEFAULT(OC_SKIP)" # Type-C Port (flex) + register "usb3_ports[2]" = "USB3_PORT_EMPTY" # Type-A Port 1 + register "usb3_ports[3]" = "USB3_PORT_EMPTY" # Type-A Port 2 + + # PL2 override 15W + register "tdp_pl2_override" = "15" + + # Send an extra VR mailbox command for the supported MPS IMVP8 model + register "SendVrMbxCmd" = "1" + + # TCC of 90C + register "tcc_offset" = "10" + + # Use default SD card detect GPIO configuration + register "sdcard_cd_gpio_default" = "GPP_A7" + + device domain 0 on + device pci 15.0 on + chip drivers/i2c/generic + register "hid" = ""ELAN0001"" + register "desc" = ""ELAN Touchscreen"" + register "irq" = "ACPI_IRQ_EDGE_LOW(GPP_E7_IRQ)" + device i2c 10 on end + end + end # I2C #0 + device pci 15.1 on + chip drivers/i2c/generic + register "hid" = ""ELAN0000"" + register "desc" = ""ELAN Touchpad"" + register "irq" = "ACPI_IRQ_LEVEL_LOW(GPP_B3_IRQ)" + register "wake" = "GPE0_DW0_05" + device i2c 15 on end + end + end # I2C #1 + device pci 19.2 on + chip drivers/i2c/nau8825 + register "irq" = "ACPI_IRQ_LEVEL_LOW(GPP_F10_IRQ)" + register "jkdet_enable" = "1" + register "jkdet_pull_enable" = "0" # R389 + register "jkdet_polarity" = "1" # ActiveLow + register "vref_impedance" = "2" # 125kOhm + register "micbias_voltage" = "6" # 2.754 + register "sar_threshold_num" = "4" + register "sar_threshold[0]" = "0x0c" + register "sar_threshold[1]" = "0x1e" + register "sar_threshold[2]" = "0x38" + register "sar_threshold[3]" = "0x60" + register "sar_hysteresis" = "1" + register "sar_voltage" = "0" # VDDA + register "sar_compare_time" = "0" # 500ns + register "sar_sampling_time" = "0" # 2us + register "short_key_debounce" = "2" # 100ms + register "jack_insert_debounce" = "7" # 512ms + register "jack_eject_debounce" = "7" # 512ms + device i2c 1a on end + end + end # I2C #4 + device pci 1e.6 on end # SDCard + device pci 1f.3 on + chip drivers/generic/max98357a + register "hid" = ""MX98357A"" + register "sdmode_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_E3)" + register "sdmode_delay" = "5" + device generic 0 on end + end + end # Intel HDA + end +end diff --git a/src/mainboard/google/glados/variants/chell/devicetree.cb b/src/mainboard/google/glados/variants/chell/devicetree.cb deleted file mode 100644 index bbc74f8d97..0000000000 --- a/src/mainboard/google/glados/variants/chell/devicetree.cb +++ /dev/null @@ -1,228 +0,0 @@ -chip soc/intel/skylake - - register "gpu_pp_up_delay_ms" = "200" - register "gpu_pp_down_delay_ms" = " 50" - register "gpu_pp_cycle_delay_ms" = "500" - register "gpu_pp_backlight_on_delay_ms" = " 1" - register "gpu_pp_backlight_off_delay_ms" = "200" - - register "gpu_pch_backlight_pwm_hz" = "1000" - - # Enable deep Sx states - register "deep_s3_enable_ac" = "0" - register "deep_s3_enable_dc" = "0" - register "deep_s5_enable_ac" = "1" - register "deep_s5_enable_dc" = "1" - register "deep_sx_config" = "DSX_EN_LAN_WAKE_PIN" - - # GPE configuration - # Note that GPE events called out in ASL code rely on this - # route. i.e. If this route changes then the affected GPE - # offset bits also need to be changed. - register "gpe0_dw0" = "GPP_B" - register "gpe0_dw1" = "GPP_D" - register "gpe0_dw2" = "GPP_E" - - # EC host command ranges are in 0x800-0x8ff & 0x200-0x20f - register "gen1_dec" = "0x00fc0801" - register "gen2_dec" = "0x000c0201" - - # Enable "Intel Speed Shift Technology" - register "speed_shift_enable" = "1" - - # Enable DPTF - register "dptf_enable" = "1" - - # FSP Configuration - register "ProbelessTrace" = "0" - register "EnableLan" = "0" - register "EnableSata" = "0" - register "SataSalpSupport" = "0" - register "SataMode" = "0" - register "SataPortsEnable[0]" = "0" - register "EnableAzalia" = "1" - register "DspEnable" = "1" - register "IoBufferOwnership" = "3" - register "EnableTraceHub" = "0" - register "SsicPortEnable" = "0" - register "SmbusEnable" = "1" - register "Cio2Enable" = "0" - register "ScsEmmcEnabled" = "1" - register "ScsEmmcHs400Enabled" = "1" - register "ScsSdCardEnabled" = "0" - register "PttSwitch" = "0" - register "SkipExtGfxScan" = "1" - register "Device4Enable" = "1" - register "HeciEnabled" = "0" - register "SaGv" = "3" - register "PmConfigSlpS3MinAssert" = "2" # 50ms - register "PmConfigSlpS4MinAssert" = "1" # 1s - register "PmConfigSlpSusMinAssert" = "1" # 500ms - register "PmConfigSlpAMinAssert" = "3" # 2s - register "PmTimerDisabled" = "1" - - register "pirqa_routing" = "PCH_IRQ11" - register "pirqb_routing" = "PCH_IRQ10" - register "pirqc_routing" = "PCH_IRQ11" - register "pirqd_routing" = "PCH_IRQ11" - register "pirqe_routing" = "PCH_IRQ11" - register "pirqf_routing" = "PCH_IRQ11" - register "pirqg_routing" = "PCH_IRQ11" - register "pirqh_routing" = "PCH_IRQ11" - - # Enable Root port 1 - register "PcieRpEnable[0]" = "1" - # Enable CLKREQ# - register "PcieRpClkReqSupport[0]" = "1" - # RP 1 uses SRCCLKREQ1# - register "PcieRpClkReqNumber[0]" = "1" - - register "usb2_ports[0]" = "USB2_PORT_LONG(OC2)" # Type-C Port 1 - register "usb2_ports[1]" = "USB2_PORT_LONG(OC3)" # Type-C Port 2 - register "usb2_ports[2]" = "USB2_PORT_MID(OC_SKIP)" # Bluetooth - register "usb2_ports[4]" = "USB2_PORT_MID(OC0)" # Type-A Port - register "usb2_ports[6]" = "USB2_PORT_FLEX(OC_SKIP)" # Camera - register "usb2_ports[8]" = "USB2_PORT_MID(OC_SKIP)" # SD - - register "usb3_ports[0]" = "USB3_PORT_DEFAULT(OC2)" # Type-C Port 1 - register "usb3_ports[1]" = "USB3_PORT_DEFAULT(OC3)" # Type-C Port 2 - register "usb3_ports[2]" = "USB3_PORT_DEFAULT(OC0)" # Type-A Port - register "usb3_ports[3]" = "USB3_PORT_DEFAULT(OC_SKIP)" # SD - - - # Must leave UART0 enabled or SD/eMMC will not work as PCI - register "SerialIoDevMode" = "{ - [PchSerialIoIndexI2C0] = PchSerialIoPci, - [PchSerialIoIndexI2C1] = PchSerialIoPci, - [PchSerialIoIndexI2C2] = PchSerialIoDisabled, - [PchSerialIoIndexI2C3] = PchSerialIoDisabled, - [PchSerialIoIndexI2C4] = PchSerialIoPci, - [PchSerialIoIndexI2C5] = PchSerialIoDisabled, - [PchSerialIoIndexSpi0] = PchSerialIoDisabled, - [PchSerialIoIndexSpi1] = PchSerialIoDisabled, - [PchSerialIoIndexUart0] = PchSerialIoPci, - [PchSerialIoIndexUart1] = PchSerialIoDisabled, - [PchSerialIoIndexUart2] = PchSerialIoSkipInit, - }" - - # I2C4 is 1.8V - register "i2c_voltage[4]" = "I2C_VOLTAGE_1V8" - - # PL2 override 15W - register "tdp_pl2_override" = "15" - - # Send an extra VR mailbox command for the supported MPS IMVP8 model - register "SendVrMbxCmd" = "1" - - # TCC of 90C - register "tcc_offset" = "10" - - # Lock Down - register "common_soc_config" = "{ - .chipset_lockdown = CHIPSET_LOCKDOWN_COREBOOT, - }" - - device cpu_cluster 0 on - device lapic 0 on end - end - device domain 0 on - device pci 00.0 on end # Host Bridge - device pci 02.0 on end # Integrated Graphics Device - device pci 14.0 on end # USB xHCI - device pci 14.1 off end # USB xDCI (OTG) - device pci 14.2 on end # Thermal Subsystem - device pci 15.0 on end # I2C #0 - device pci 15.1 on - chip drivers/i2c/generic - register "hid" = ""ELAN0000"" - register "desc" = ""ELAN Touchpad"" - register "irq" = "ACPI_IRQ_LEVEL_LOW(GPP_B3_IRQ)" - register "wake" = "GPE0_DW0_05" - device i2c 15 on end - end - end # I2C #1 - device pci 15.2 off end # I2C #2 - device pci 15.3 off end # I2C #3 - device pci 16.0 on end # Management Engine Interface 1 - device pci 16.1 off end # Management Engine Interface 2 - device pci 16.2 off end # Management Engine IDE-R - device pci 16.3 off end # Management Engine KT Redirection - device pci 16.4 off end # Management Engine Interface 3 - device pci 17.0 off end # SATA - device pci 19.0 on end # UART #2 - device pci 19.1 off end # I2C #5 - device pci 19.2 on - chip drivers/i2c/nau8825 - register "irq" = "ACPI_IRQ_LEVEL_LOW(GPP_F10_IRQ)" - register "jkdet_enable" = "1" - register "jkdet_pull_enable" = "0" # R389 - register "jkdet_polarity" = "1" # ActiveLow - register "vref_impedance" = "2" # 125kOhm - register "micbias_voltage" = "6" # 2.754 - register "sar_threshold_num" = "4" - register "sar_threshold[0]" = "0x0c" - register "sar_threshold[1]" = "0x1c" - register "sar_threshold[2]" = "0x38" - register "sar_threshold[3]" = "0x60" - register "sar_hysteresis" = "1" - register "sar_voltage" = "0" # VDDA - register "sar_compare_time" = "0" # 500ns - register "sar_sampling_time" = "0" # 2us - register "short_key_debounce" = "2" # 100ms - register "jack_insert_debounce" = "7" # 512ms - register "jack_eject_debounce" = "7" # 512ms - device i2c 1a on end - end - chip drivers/i2c/generic - register "hid" = ""INT343B"" - register "desc" = ""SSM4567 Left Speaker Amp"" - register "uid" = "0" - device i2c 34 on end - end - chip drivers/i2c/generic - register "hid" = ""INT343B"" - register "desc" = ""SSM4567 Right Speaker Amp"" - register "uid" = "1" - device i2c 35 on end - end - end # I2C #4 - device pci 1c.0 on - chip drivers/intel/wifi - register "wake" = "GPE0_DW0_16" - device pci 00.0 on end - end - end # PCI Express Port 1 - device pci 1c.1 off end # PCI Express Port 2 - device pci 1c.2 off end # PCI Express Port 3 - device pci 1c.3 off end # PCI Express Port 4 - device pci 1c.4 off end # PCI Express Port 5 - device pci 1c.5 off end # PCI Express Port 6 - device pci 1c.6 off end # PCI Express Port 7 - device pci 1c.7 off end # PCI Express Port 8 - device pci 1d.0 off end # PCI Express Port 9 - device pci 1d.1 off end # PCI Express Port 10 - device pci 1d.2 off end # PCI Express Port 11 - device pci 1d.3 off end # PCI Express Port 12 - device pci 1e.0 on end # UART #0 - device pci 1e.1 off end # UART #1 - device pci 1e.2 off end # GSPI #0 - device pci 1e.3 off end # GSPI #1 - device pci 1e.4 on end # eMMC - device pci 1e.5 off end # SDIO - device pci 1e.6 off end # SDCard - device pci 1f.0 on - chip drivers/pc80/tpm - device pnp 0c31.0 on end - end - chip ec/google/chromeec - device pnp 0c09.0 on end - end - end # LPC Interface - device pci 1f.1 on end # P2SB - device pci 1f.2 on end # Power Management Controller - device pci 1f.3 on end # Intel HDA - device pci 1f.4 on end # SMBus - device pci 1f.5 on end # PCH SPI - device pci 1f.6 off end # GbE - end -end diff --git a/src/mainboard/google/glados/variants/chell/overridetree.cb b/src/mainboard/google/glados/variants/chell/overridetree.cb new file mode 100644 index 0000000000..c6ccd208aa --- /dev/null +++ b/src/mainboard/google/glados/variants/chell/overridetree.cb @@ -0,0 +1,73 @@ +chip soc/intel/skylake + + register "PmConfigSlpS4MinAssert" = "1" # 1s + register "PmConfigSlpSusMinAssert" = "1" # 500ms + + register "usb2_ports[0]" = "USB2_PORT_LONG(OC2)" # Type-C Port 1 + register "usb2_ports[1]" = "USB2_PORT_LONG(OC3)" # Type-C Port 2 + register "usb2_ports[2]" = "USB2_PORT_MID(OC_SKIP)" # Bluetooth + register "usb2_ports[4]" = "USB2_PORT_MID(OC0)" # Type-A Port + register "usb2_ports[6]" = "USB2_PORT_FLEX(OC_SKIP)" # Camera + register "usb2_ports[8]" = "USB2_PORT_MID(OC_SKIP)" # SD + + register "usb3_ports[0]" = "USB3_PORT_DEFAULT(OC2)" # Type-C Port 1 + register "usb3_ports[1]" = "USB3_PORT_DEFAULT(OC3)" # Type-C Port 2 + register "usb3_ports[2]" = "USB3_PORT_DEFAULT(OC0)" # Type-A Port + register "usb3_ports[3]" = "USB3_PORT_DEFAULT(OC_SKIP)" # SD + + # PL2 override 15W + register "tdp_pl2_override" = "15" + + # Send an extra VR mailbox command for the supported MPS IMVP8 model + register "SendVrMbxCmd" = "1" + + # TCC of 90C + register "tcc_offset" = "10" + + device domain 0 on + device pci 15.1 on + chip drivers/i2c/generic + register "hid" = ""ELAN0000"" + register "desc" = ""ELAN Touchpad"" + register "irq" = "ACPI_IRQ_LEVEL_LOW(GPP_B3_IRQ)" + register "wake" = "GPE0_DW0_05" + device i2c 15 on end + end + end # I2C #1 + device pci 19.2 on + chip drivers/i2c/nau8825 + register "irq" = "ACPI_IRQ_LEVEL_LOW(GPP_F10_IRQ)" + register "jkdet_enable" = "1" + register "jkdet_pull_enable" = "0" # R389 + register "jkdet_polarity" = "1" # ActiveLow + register "vref_impedance" = "2" # 125kOhm + register "micbias_voltage" = "6" # 2.754 + register "sar_threshold_num" = "4" + register "sar_threshold[0]" = "0x0c" + register "sar_threshold[1]" = "0x1c" + register "sar_threshold[2]" = "0x38" + register "sar_threshold[3]" = "0x60" + register "sar_hysteresis" = "1" + register "sar_voltage" = "0" # VDDA + register "sar_compare_time" = "0" # 500ns + register "sar_sampling_time" = "0" # 2us + register "short_key_debounce" = "2" # 100ms + register "jack_insert_debounce" = "7" # 512ms + register "jack_eject_debounce" = "7" # 512ms + device i2c 1a on end + end + chip drivers/i2c/generic + register "hid" = ""INT343B"" + register "desc" = ""SSM4567 Left Speaker Amp"" + register "uid" = "0" + device i2c 34 on end + end + chip drivers/i2c/generic + register "hid" = ""INT343B"" + register "desc" = ""SSM4567 Right Speaker Amp"" + register "uid" = "1" + device i2c 35 on end + end + end # I2C #4 + end +end diff --git a/src/mainboard/google/glados/variants/glados/devicetree.cb b/src/mainboard/google/glados/variants/glados/devicetree.cb deleted file mode 100644 index 9cd5ac986f..0000000000 --- a/src/mainboard/google/glados/variants/glados/devicetree.cb +++ /dev/null @@ -1,234 +0,0 @@ -chip soc/intel/skylake - - register "gpu_pp_up_delay_ms" = "200" - register "gpu_pp_down_delay_ms" = " 50" - register "gpu_pp_cycle_delay_ms" = "500" - register "gpu_pp_backlight_on_delay_ms" = " 1" - register "gpu_pp_backlight_off_delay_ms" = "200" - - register "gpu_pch_backlight_pwm_hz" = "1000" - - # Enable deep Sx states - register "deep_s3_enable_ac" = "0" - register "deep_s3_enable_dc" = "0" - register "deep_s5_enable_ac" = "1" - register "deep_s5_enable_dc" = "1" - register "deep_sx_config" = "DSX_EN_LAN_WAKE_PIN" - - # GPE configuration - # Note that GPE events called out in ASL code rely on this - # route. i.e. If this route changes then the affected GPE - # offset bits also need to be changed. - register "gpe0_dw0" = "GPP_B" - register "gpe0_dw1" = "GPP_D" - register "gpe0_dw2" = "GPP_E" - - # EC host command ranges are in 0x800-0x8ff & 0x200-0x20f - register "gen1_dec" = "0x00fc0801" - register "gen2_dec" = "0x000c0201" - - # Enable "Intel Speed Shift Technology" - register "speed_shift_enable" = "1" - - # Enable DPTF - register "dptf_enable" = "1" - - # FSP Configuration - register "ProbelessTrace" = "0" - register "EnableLan" = "0" - register "EnableSata" = "0" - register "SataSalpSupport" = "0" - register "SataMode" = "0" - register "SataPortsEnable[0]" = "0" - register "EnableAzalia" = "1" - register "DspEnable" = "1" - register "IoBufferOwnership" = "3" - register "EnableTraceHub" = "0" - register "SsicPortEnable" = "0" - register "SmbusEnable" = "1" - register "Cio2Enable" = "0" - register "ScsEmmcEnabled" = "1" - register "ScsEmmcHs400Enabled" = "1" - register "ScsSdCardEnabled" = "2" - register "PttSwitch" = "0" - register "SkipExtGfxScan" = "1" - register "Device4Enable" = "1" - register "HeciEnabled" = "0" - register "SaGv" = "3" - register "PmConfigSlpS3MinAssert" = "2" # 50ms - register "PmConfigSlpS4MinAssert" = "1" # 1s - register "PmConfigSlpSusMinAssert" = "1" # 500ms - register "PmConfigSlpAMinAssert" = "3" # 2s - register "PmTimerDisabled" = "1" - - register "pirqa_routing" = "PCH_IRQ11" - register "pirqb_routing" = "PCH_IRQ10" - register "pirqc_routing" = "PCH_IRQ11" - register "pirqd_routing" = "PCH_IRQ11" - register "pirqe_routing" = "PCH_IRQ11" - register "pirqf_routing" = "PCH_IRQ11" - register "pirqg_routing" = "PCH_IRQ11" - register "pirqh_routing" = "PCH_IRQ11" - - # Enable Root port 1 - register "PcieRpEnable[0]" = "1" - # Enable CLKREQ# - register "PcieRpClkReqSupport[0]" = "1" - # RP 1 uses SRCCLKREQ1# - register "PcieRpClkReqNumber[0]" = "1" - - register "usb2_ports[0]" = "USB2_PORT_TYPE_C(OC2)" # Type-C Port (board) - register "usb2_ports[1]" = "USB2_PORT_MAX(OC3)" # Type-C Port (flex) - register "usb2_ports[2]" = "USB2_PORT_MID(OC_SKIP)" # Bluetooth - register "usb2_ports[4]" = "USB2_PORT_MID(OC0)" # Type-A Port 1 - register "usb2_ports[6]" = "USB2_PORT_FLEX(OC_SKIP)" # Camera - register "usb2_ports[8]" = "USB2_PORT_MID(OC1)" # Type-A Port 2 - - register "usb3_ports[0]" = "USB3_PORT_DEFAULT(OC2)" # Type-C Port (board) - register "usb3_ports[1]" = "USB3_PORT_DEFAULT(OC3)" # Type-C Port (flex) - register "usb3_ports[2]" = "USB3_PORT_DEFAULT(OC0)" # Type-A Port 1 - register "usb3_ports[3]" = "USB3_PORT_DEFAULT(OC1)" # Type-A Port 2 - - # Must leave UART0 enabled or SD/eMMC will not work as PCI - register "SerialIoDevMode" = "{ - [PchSerialIoIndexI2C0] = PchSerialIoPci, - [PchSerialIoIndexI2C1] = PchSerialIoPci, - [PchSerialIoIndexI2C2] = PchSerialIoDisabled, - [PchSerialIoIndexI2C3] = PchSerialIoDisabled, - [PchSerialIoIndexI2C4] = PchSerialIoPci, - [PchSerialIoIndexI2C5] = PchSerialIoDisabled, - [PchSerialIoIndexSpi0] = PchSerialIoDisabled, - [PchSerialIoIndexSpi1] = PchSerialIoDisabled, - [PchSerialIoIndexUart0] = PchSerialIoPci, - [PchSerialIoIndexUart1] = PchSerialIoDisabled, - [PchSerialIoIndexUart2] = PchSerialIoSkipInit, - }" - - # I2C4 is 1.8V - register "i2c_voltage[4]" = "I2C_VOLTAGE_1V8" - - # PL2 override 15W - register "tdp_pl2_override" = "15" - - # Send an extra VR mailbox command for the supported MPS IMVP8 model - register "SendVrMbxCmd" = "1" - - # TCC of 90C - register "tcc_offset" = "10" - - # Lock Down - register "common_soc_config" = "{ - .chipset_lockdown = CHIPSET_LOCKDOWN_COREBOOT, - }" - - device cpu_cluster 0 on - device lapic 0 on end - end - device domain 0 on - device pci 00.0 on end # Host Bridge - device pci 02.0 on end # Integrated Graphics Device - device pci 14.0 on end # USB xHCI - device pci 14.1 off end # USB xDCI (OTG) - device pci 14.2 on end # Thermal Subsystem - device pci 15.0 on - chip drivers/i2c/generic - register "hid" = ""ELAN0001"" - register "desc" = ""ELAN Touchscreen"" - register "irq" = "ACPI_IRQ_EDGE_LOW(GPP_E7_IRQ)" - device i2c 10 on end - end - end # I2C #0 - device pci 15.1 on - chip drivers/i2c/generic - register "hid" = ""ELAN0000"" - register "desc" = ""ELAN Touchpad"" - register "irq" = "ACPI_IRQ_LEVEL_LOW(GPP_B3_IRQ)" - register "wake" = "GPE0_DW0_05" - device i2c 15 on end - end - end # I2C #1 - device pci 15.2 off end # I2C #2 - device pci 15.3 off end # I2C #3 - device pci 16.0 on end # Management Engine Interface 1 - device pci 16.1 off end # Management Engine Interface 2 - device pci 16.2 off end # Management Engine IDE-R - device pci 16.3 off end # Management Engine KT Redirection - device pci 16.4 off end # Management Engine Interface 3 - device pci 17.0 off end # SATA - device pci 19.0 on end # UART #2 - device pci 19.1 off end # I2C #5 - device pci 19.2 on - chip drivers/i2c/nau8825 - register "irq" = "ACPI_IRQ_LEVEL_LOW(GPP_F10_IRQ)" - register "jkdet_enable" = "1" - register "jkdet_pull_enable" = "0" # R389 - register "jkdet_polarity" = "1" # ActiveLow - register "vref_impedance" = "2" # 125kOhm - register "micbias_voltage" = "6" # 2.754 - register "sar_threshold_num" = "4" - register "sar_threshold[0]" = "0x0c" - register "sar_threshold[1]" = "0x1e" - register "sar_threshold[2]" = "0x38" - register "sar_threshold[3]" = "0x60" - register "sar_hysteresis" = "1" - register "sar_voltage" = "0" # VDDA - register "sar_compare_time" = "0" # 500ns - register "sar_sampling_time" = "0" # 2us - register "short_key_debounce" = "2" # 100ms - register "jack_insert_debounce" = "7" # 512ms - register "jack_eject_debounce" = "7" # 512ms - device i2c 1a on end - end - chip drivers/i2c/generic - register "hid" = ""INT343B"" - register "desc" = ""SSM4567 Left Speaker Amp"" - register "uid" = "0" - device i2c 34 on end - end - chip drivers/i2c/generic - register "hid" = ""INT343B"" - register "desc" = ""SSM4567 Right Speaker Amp"" - register "uid" = "1" - device i2c 35 on end - end - end # I2C #4 - device pci 1c.0 on - chip drivers/intel/wifi - register "wake" = "GPE0_DW0_16" - device pci 00.0 on end - end - end # PCI Express Port 1 - device pci 1c.1 off end # PCI Express Port 2 - device pci 1c.2 off end # PCI Express Port 3 - device pci 1c.3 off end # PCI Express Port 4 - device pci 1c.4 off end # PCI Express Port 5 - device pci 1c.5 off end # PCI Express Port 6 - device pci 1c.6 off end # PCI Express Port 7 - device pci 1c.7 off end # PCI Express Port 8 - device pci 1d.0 off end # PCI Express Port 9 - device pci 1d.1 off end # PCI Express Port 10 - device pci 1d.2 off end # PCI Express Port 11 - device pci 1d.3 off end # PCI Express Port 12 - device pci 1e.0 on end # UART #0 - device pci 1e.1 off end # UART #1 - device pci 1e.2 off end # GSPI #0 - device pci 1e.3 off end # GSPI #1 - device pci 1e.4 on end # eMMC - device pci 1e.5 off end # SDIO - device pci 1e.6 on end # SDCard - device pci 1f.0 on - chip drivers/pc80/tpm - device pnp 0c31.0 on end - end - chip ec/google/chromeec - device pnp 0c09.0 on end - end - end # LPC Interface - device pci 1f.1 on end # P2SB - device pci 1f.2 on end # Power Management Controller - device pci 1f.3 on end # Intel HDA - device pci 1f.4 on end # SMBus - device pci 1f.5 on end # PCH SPI - device pci 1f.6 off end # GbE - end -end diff --git a/src/mainboard/google/glados/variants/glados/overridetree.cb b/src/mainboard/google/glados/variants/glados/overridetree.cb new file mode 100644 index 0000000000..1bc69abb17 --- /dev/null +++ b/src/mainboard/google/glados/variants/glados/overridetree.cb @@ -0,0 +1,84 @@ +chip soc/intel/skylake + + register "ScsSdCardEnabled" = "2" + + register "PmConfigSlpS4MinAssert" = "1" # 1s + register "PmConfigSlpSusMinAssert" = "1" # 500ms + + register "usb2_ports[0]" = "USB2_PORT_TYPE_C(OC2)" # Type-C Port (board) + register "usb2_ports[1]" = "USB2_PORT_MAX(OC3)" # Type-C Port (flex) + register "usb2_ports[2]" = "USB2_PORT_MID(OC_SKIP)" # Bluetooth + register "usb2_ports[4]" = "USB2_PORT_MID(OC0)" # Type-A Port 1 + register "usb2_ports[6]" = "USB2_PORT_FLEX(OC_SKIP)" # Camera + register "usb2_ports[8]" = "USB2_PORT_MID(OC1)" # Type-A Port 2 + + register "usb3_ports[0]" = "USB3_PORT_DEFAULT(OC2)" # Type-C Port (board) + register "usb3_ports[1]" = "USB3_PORT_DEFAULT(OC3)" # Type-C Port (flex) + register "usb3_ports[2]" = "USB3_PORT_DEFAULT(OC0)" # Type-A Port 1 + register "usb3_ports[3]" = "USB3_PORT_DEFAULT(OC1)" # Type-A Port 2 + + # PL2 override 15W + register "tdp_pl2_override" = "15" + + # Send an extra VR mailbox command for the supported MPS IMVP8 model + register "SendVrMbxCmd" = "1" + + # TCC of 90C + register "tcc_offset" = "10" + + device domain 0 on + device pci 15.0 on + chip drivers/i2c/generic + register "hid" = ""ELAN0001"" + register "desc" = ""ELAN Touchscreen"" + register "irq" = "ACPI_IRQ_EDGE_LOW(GPP_E7_IRQ)" + device i2c 10 on end + end + end # I2C #0 + device pci 15.1 on + chip drivers/i2c/generic + register "hid" = ""ELAN0000"" + register "desc" = ""ELAN Touchpad"" + register "irq" = "ACPI_IRQ_LEVEL_LOW(GPP_B3_IRQ)" + register "wake" = "GPE0_DW0_05" + device i2c 15 on end + end + end # I2C #1 + device pci 19.2 on + chip drivers/i2c/nau8825 + register "irq" = "ACPI_IRQ_LEVEL_LOW(GPP_F10_IRQ)" + register "jkdet_enable" = "1" + register "jkdet_pull_enable" = "0" # R389 + register "jkdet_polarity" = "1" # ActiveLow + register "vref_impedance" = "2" # 125kOhm + register "micbias_voltage" = "6" # 2.754 + register "sar_threshold_num" = "4" + register "sar_threshold[0]" = "0x0c" + register "sar_threshold[1]" = "0x1e" + register "sar_threshold[2]" = "0x38" + register "sar_threshold[3]" = "0x60" + register "sar_hysteresis" = "1" + register "sar_voltage" = "0" # VDDA + register "sar_compare_time" = "0" # 500ns + register "sar_sampling_time" = "0" # 2us + register "short_key_debounce" = "2" # 100ms + register "jack_insert_debounce" = "7" # 512ms + register "jack_eject_debounce" = "7" # 512ms + device i2c 1a on end + end + chip drivers/i2c/generic + register "hid" = ""INT343B"" + register "desc" = ""SSM4567 Left Speaker Amp"" + register "uid" = "0" + device i2c 34 on end + end + chip drivers/i2c/generic + register "hid" = ""INT343B"" + register "desc" = ""SSM4567 Right Speaker Amp"" + register "uid" = "1" + device i2c 35 on end + end + end # I2C #4 + device pci 1e.6 on end # SDCard + end +end diff --git a/src/mainboard/google/glados/variants/lars/overridetree.cb b/src/mainboard/google/glados/variants/lars/overridetree.cb new file mode 100644 index 0000000000..ce32b6b0c9 --- /dev/null +++ b/src/mainboard/google/glados/variants/lars/overridetree.cb @@ -0,0 +1,67 @@ +chip soc/intel/skylake + + register "usb2_ports[0]" = "USB2_PORT_TYPE_C(OC0)" # Type-C Port 1 + register "usb2_ports[1]" = "USB2_PORT_FLEX(OC_SKIP)" # Camera + register "usb2_ports[2]" = "USB2_PORT_MID(OC_SKIP)" # Bluetooth + register "usb2_ports[4]" = "USB2_PORT_MID(OC2)" # Type-A Port (card) + register "usb2_ports[5]" = "USB2_PORT_MID(OC_SKIP)" # SD + register "usb2_ports[8]" = "USB2_PORT_LONG(OC3)" # Type-A Port (board) + + register "usb3_ports[0]" = "USB3_PORT_DEFAULT(OC0)" # Type-C Port 1 + register "usb3_ports[1]" = "USB3_PORT_DEFAULT(OC_SKIP)" # SD + register "usb3_ports[2]" = "USB3_PORT_DEFAULT(OC2)" # Type-A Port (card) + register "usb3_ports[3]" = "USB3_PORT_DEFAULT(OC3)" # Type-A Port (board) + + device domain 0 on + device pci 15.0 on + chip drivers/i2c/generic + register "hid" = ""ELAN0001"" + register "desc" = ""ELAN Touchscreen"" + register "irq" = "ACPI_IRQ_EDGE_LOW(GPP_E7_IRQ)" + device i2c 10 on end + end + end # I2C #0 + device pci 15.1 on + chip drivers/i2c/generic + register "hid" = ""ELAN0000"" + register "desc" = ""ELAN Touchpad"" + register "irq" = "ACPI_IRQ_LEVEL_LOW(GPP_B3_IRQ)" + register "wake" = "GPE0_DW0_05" + device i2c 15 on end + end + end # I2C #1 + device pci 19.2 on + chip drivers/i2c/nau8825 + register "irq" = "ACPI_IRQ_LEVEL_LOW(GPP_F10_IRQ)" + register "jkdet_enable" = "1" + register "jkdet_pull_enable" = "1" + register "jkdet_pull_up" = "1" + register "jkdet_polarity" = "1" # ActiveLow + register "vref_impedance" = "2" # 125kOhm + register "micbias_voltage" = "6" # 2.754 + register "sar_threshold_num" = "4" + register "sar_threshold[0]" = "0x08" + register "sar_threshold[1]" = "0x12" + register "sar_threshold[2]" = "0x26" + register "sar_threshold[3]" = "0x73" + register "sar_hysteresis" = "0" + register "sar_voltage" = "6" + register "sar_compare_time" = "1" # 1us + register "sar_sampling_time" = "1" # 4us + register "short_key_debounce" = "3" # 30ms + register "jack_insert_debounce" = "7" # 512ms + register "jack_eject_debounce" = "0" + device i2c 1a on end + end + end # I2C #4 + device pci 1e.6 off end # SDCard + device pci 1f.3 on + chip drivers/generic/max98357a + register "hid" = ""MX98357A"" + register "sdmode_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_B2)" + register "sdmode_delay" = "5" + device generic 0 on end + end + end # Intel HDA + end +end diff --git a/src/mainboard/google/glados/variants/sentry/devicetree.cb b/src/mainboard/google/glados/variants/sentry/devicetree.cb deleted file mode 100644 index 502aad04ea..0000000000 --- a/src/mainboard/google/glados/variants/sentry/devicetree.cb +++ /dev/null @@ -1,249 +0,0 @@ -chip soc/intel/skylake - - register "gpu_pp_up_delay_ms" = "200" - register "gpu_pp_down_delay_ms" = " 50" - register "gpu_pp_cycle_delay_ms" = "500" - register "gpu_pp_backlight_on_delay_ms" = " 1" - register "gpu_pp_backlight_off_delay_ms" = "200" - - register "gpu_pch_backlight_pwm_hz" = "1000" - - # Enable deep Sx states - register "deep_s3_enable_ac" = "0" - register "deep_s3_enable_dc" = "0" - register "deep_s5_enable_ac" = "1" - register "deep_s5_enable_dc" = "1" - register "deep_sx_config" = "DSX_EN_LAN_WAKE_PIN" - - # GPE configuration - # Note that GPE events called out in ASL code rely on this - # route. i.e. If this route changes then the affected GPE - # offset bits also need to be changed. - register "gpe0_dw0" = "GPP_B" - register "gpe0_dw1" = "GPP_D" - register "gpe0_dw2" = "GPP_E" - - # EC host command ranges are in 0x800-0x8ff & 0x200-0x20f - register "gen1_dec" = "0x00fc0801" - register "gen2_dec" = "0x000c0201" - - # Enable "Intel Speed Shift Technology" - register "speed_shift_enable" = "1" - - # Enable DPTF - register "dptf_enable" = "1" - - # FSP Configuration - register "ProbelessTrace" = "0" - register "EnableLan" = "0" - register "EnableSata" = "0" - register "SataSalpSupport" = "0" - register "SataMode" = "0" - register "SataPortsEnable[0]" = "0" - register "EnableAzalia" = "1" - register "DspEnable" = "1" - register "IoBufferOwnership" = "3" - register "EnableTraceHub" = "0" - register "SsicPortEnable" = "0" - register "SmbusEnable" = "1" - register "Cio2Enable" = "0" - register "ScsEmmcEnabled" = "1" - register "ScsEmmcHs400Enabled" = "1" - register "ScsSdCardEnabled" = "2" - register "PttSwitch" = "0" - register "SkipExtGfxScan" = "1" - register "Device4Enable" = "1" - register "HeciEnabled" = "0" - register "SaGv" = "3" - register "PmConfigSlpS3MinAssert" = "2" # 50ms - register "PmConfigSlpS4MinAssert" = "4" # 4s - register "PmConfigSlpSusMinAssert" = "3" # 4s - register "PmConfigSlpAMinAssert" = "3" # 2s - register "PmTimerDisabled" = "1" - - register "pirqa_routing" = "PCH_IRQ11" - register "pirqb_routing" = "PCH_IRQ10" - register "pirqc_routing" = "PCH_IRQ11" - register "pirqd_routing" = "PCH_IRQ11" - register "pirqe_routing" = "PCH_IRQ11" - register "pirqf_routing" = "PCH_IRQ11" - register "pirqg_routing" = "PCH_IRQ11" - register "pirqh_routing" = "PCH_IRQ11" - - # Enable Root port 1 - register "PcieRpEnable[0]" = "1" - # Enable CLKREQ# - register "PcieRpClkReqSupport[0]" = "1" - # RP 1 uses SRCCLKREQ1# - register "PcieRpClkReqNumber[0]" = "1" - - register "usb2_ports[0]" = "USB2_PORT_TYPE_C(OC0)" # Type-C Port 1 - register "usb2_ports[1]" = "USB2_PORT_TYPE_C(OC1)" # Type-C Port 2 - register "usb2_ports[2]" = "USB2_PORT_MID(OC_SKIP)" # Bluetooth - register "usb2_ports[4]" = "USB2_PORT_MID(OC2)" # Type-A Port (card) - register "usb2_ports[6]" = "USB2_PORT_FLEX(OC_SKIP)" # Camera - register "usb2_ports[8]" = "USB2_PORT_LONG(OC3)" # Type-A Port (board) - - register "usb3_ports[0]" = "USB3_PORT_DEFAULT(OC0)" # Type-C Port 1 - register "usb3_ports[1]" = "USB3_PORT_DEFAULT(OC1)" # Type-C Port 2 - register "usb3_ports[2]" = "USB3_PORT_DEFAULT(OC2)" # Type-A Port (card) - register "usb3_ports[3]" = "USB3_PORT_DEFAULT(OC3)" # Type-A Port (board) - - # Must leave UART0 enabled or SD/eMMC will not work as PCI - register "SerialIoDevMode" = "{ - [PchSerialIoIndexI2C0] = PchSerialIoPci, - [PchSerialIoIndexI2C1] = PchSerialIoPci, - [PchSerialIoIndexI2C2] = PchSerialIoDisabled, - [PchSerialIoIndexI2C3] = PchSerialIoDisabled, - [PchSerialIoIndexI2C4] = PchSerialIoPci, - [PchSerialIoIndexI2C5] = PchSerialIoDisabled, - [PchSerialIoIndexSpi0] = PchSerialIoDisabled, - [PchSerialIoIndexSpi1] = PchSerialIoDisabled, - [PchSerialIoIndexUart0] = PchSerialIoPci, - [PchSerialIoIndexUart1] = PchSerialIoDisabled, - [PchSerialIoIndexUart2] = PchSerialIoSkipInit, - }" - - # I2C0 is 3.3V - register "i2c_voltage[0]" = "I2C_VOLTAGE_3V3" - - # I2C4 is 1.8V - register "i2c_voltage[4]" = "I2C_VOLTAGE_1V8" - - # PL2 override 25W - register "tdp_pl2_override" = "25" - - # Send an extra VR mailbox command for the PS4 exit issue - register "SendVrMbxCmd" = "2" - - # Use default SD card detect GPIO configuration - register "sdcard_cd_gpio_default" = "GPP_A7" - - # Lock Down - register "common_soc_config" = "{ - .chipset_lockdown = CHIPSET_LOCKDOWN_COREBOOT, - }" - - device cpu_cluster 0 on - device lapic 0 on end - end - device domain 0 on - device pci 00.0 on end # Host Bridge - device pci 02.0 on end # Integrated Graphics Device - device pci 14.0 on end # USB xHCI - device pci 14.1 off end # USB xDCI (OTG) - device pci 14.2 on end # Thermal Subsystem - device pci 15.0 on - chip drivers/i2c/generic - register "hid" = ""RAYD0001"" - register "desc" = ""Raydium Touchscreen"" - register "irq" = "ACPI_IRQ_EDGE_LOW(GPP_E7_IRQ)" - device i2c 39 on end - end - end # I2C #0 - device pci 15.1 on - chip drivers/i2c/generic - register "hid" = ""ELAN0000"" - register "desc" = ""ELAN Touchpad"" - register "irq" = "ACPI_IRQ_LEVEL_LOW(GPP_B3_IRQ)" - register "wake" = "GPE0_DW0_05" - device i2c 15 on end - end - end # I2C #1 - device pci 15.2 off end # I2C #2 - device pci 15.3 off end # I2C #3 - device pci 16.0 on end # Management Engine Interface 1 - device pci 16.1 off end # Management Engine Interface 2 - device pci 16.2 off end # Management Engine IDE-R - device pci 16.3 off end # Management Engine KT Redirection - device pci 16.4 off end # Management Engine Interface 3 - device pci 17.0 off end # SATA - device pci 19.0 on end # UART #2 - device pci 19.1 off end # I2C #5 - device pci 19.2 on - chip drivers/i2c/nau8825 - register "irq" = "ACPI_IRQ_LEVEL_LOW(GPP_F10_IRQ)" - register "jkdet_enable" = "1" - register "jkdet_pull_enable" = "1" - register "jkdet_pull_up" = "1" - register "jkdet_polarity" = "1" # ActiveLow - register "vref_impedance" = "2" # 125kOhm - register "micbias_voltage" = "6" # 2.754 - register "sar_threshold_num" = "4" - register "sar_threshold[0]" = "0x08" - register "sar_threshold[1]" = "0x12" - register "sar_threshold[2]" = "0x26" - register "sar_threshold[3]" = "0x73" - register "sar_hysteresis" = "0" - register "sar_voltage" = "6" - register "sar_compare_time" = "1" # 1us - register "sar_sampling_time" = "1" # 4us - register "short_key_debounce" = "3" # 30ms - register "jack_insert_debounce" = "7" # 512ms - register "jack_eject_debounce" = "0" - device i2c 1a on end - end - chip drivers/i2c/generic - register "hid" = ""INT343B"" - register "desc" = ""SSM4567 Left Speaker Amp"" - register "uid" = "0" - register "device_present_gpio" = "GPP_E3" - device i2c 34 on end - end - chip drivers/i2c/generic - register "hid" = ""INT343B"" - register "desc" = ""SSM4567 Right Speaker Amp"" - register "uid" = "1" - register "device_present_gpio" = "GPP_E3" - device i2c 35 on end - end - end # I2C #4 - device pci 1c.0 on - chip drivers/intel/wifi - register "wake" = "GPE0_DW0_16" - device pci 00.0 on end - end - end # PCI Express Port 1 - device pci 1c.1 off end # PCI Express Port 2 - device pci 1c.2 off end # PCI Express Port 3 - device pci 1c.3 off end # PCI Express Port 4 - device pci 1c.4 off end # PCI Express Port 5 - device pci 1c.5 off end # PCI Express Port 6 - device pci 1c.6 off end # PCI Express Port 7 - device pci 1c.7 off end # PCI Express Port 8 - device pci 1d.0 off end # PCI Express Port 9 - device pci 1d.1 off end # PCI Express Port 10 - device pci 1d.2 off end # PCI Express Port 11 - device pci 1d.3 off end # PCI Express Port 12 - device pci 1e.0 on end # UART #0 - device pci 1e.1 off end # UART #1 - device pci 1e.2 off end # GSPI #0 - device pci 1e.3 off end # GSPI #1 - device pci 1e.4 on end # eMMC - device pci 1e.5 off end # SDIO - device pci 1e.6 on end # SDCard - device pci 1f.0 on - chip drivers/pc80/tpm - device pnp 0c31.0 on end - end - chip ec/google/chromeec - device pnp 0c09.0 on end - end - end # LPC Interface - device pci 1f.1 on end # P2SB - device pci 1f.2 on end # Power Management Controller - device pci 1f.3 on - chip drivers/generic/max98357a - register "hid" = ""MX98357A"" - register "sdmode_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_E3)" - register "device_present_gpio" = "GPP_E3" - register "device_present_gpio_invert" = "1" - register "sdmode_delay" = "5" - device generic 0 on end - end - end # Intel HDA - device pci 1f.4 on end # SMBus - device pci 1f.5 on end # PCH SPI - device pci 1f.6 off end # GbE - end -end diff --git a/src/mainboard/google/glados/variants/sentry/overridetree.cb b/src/mainboard/google/glados/variants/sentry/overridetree.cb new file mode 100644 index 0000000000..08d3dd3aba --- /dev/null +++ b/src/mainboard/google/glados/variants/sentry/overridetree.cb @@ -0,0 +1,91 @@ +chip soc/intel/skylake + + register "ScsSdCardEnabled" = "2" + + register "usb2_ports[0]" = "USB2_PORT_TYPE_C(OC0)" # Type-C Port 1 + register "usb2_ports[1]" = "USB2_PORT_TYPE_C(OC1)" # Type-C Port 2 + register "usb2_ports[2]" = "USB2_PORT_MID(OC_SKIP)" # Bluetooth + register "usb2_ports[4]" = "USB2_PORT_MID(OC2)" # Type-A Port (card) + register "usb2_ports[6]" = "USB2_PORT_FLEX(OC_SKIP)" # Camera + register "usb2_ports[8]" = "USB2_PORT_LONG(OC3)" # Type-A Port (board) + + register "usb3_ports[0]" = "USB3_PORT_DEFAULT(OC0)" # Type-C Port 1 + register "usb3_ports[1]" = "USB3_PORT_DEFAULT(OC1)" # Type-C Port 2 + register "usb3_ports[2]" = "USB3_PORT_DEFAULT(OC2)" # Type-A Port (card) + register "usb3_ports[3]" = "USB3_PORT_DEFAULT(OC3)" # Type-A Port (board) + + # I2C0 is 3.3V + register "i2c_voltage[0]" = "I2C_VOLTAGE_3V3" + + # Use default SD card detect GPIO configuration + register "sdcard_cd_gpio_default" = "GPP_A7" + + device domain 0 on + device pci 15.0 on + chip drivers/i2c/generic + register "hid" = ""RAYD0001"" + register "desc" = ""Raydium Touchscreen"" + register "irq" = "ACPI_IRQ_EDGE_LOW(GPP_E7_IRQ)" + device i2c 39 on end + end + end # I2C #0 + device pci 15.1 on + chip drivers/i2c/generic + register "hid" = ""ELAN0000"" + register "desc" = ""ELAN Touchpad"" + register "irq" = "ACPI_IRQ_LEVEL_LOW(GPP_B3_IRQ)" + register "wake" = "GPE0_DW0_05" + device i2c 15 on end + end + end # I2C #1 + device pci 19.2 on + chip drivers/i2c/nau8825 + register "irq" = "ACPI_IRQ_LEVEL_LOW(GPP_F10_IRQ)" + register "jkdet_enable" = "1" + register "jkdet_pull_enable" = "1" + register "jkdet_pull_up" = "1" + register "jkdet_polarity" = "1" # ActiveLow + register "vref_impedance" = "2" # 125kOhm + register "micbias_voltage" = "6" # 2.754 + register "sar_threshold_num" = "4" + register "sar_threshold[0]" = "0x08" + register "sar_threshold[1]" = "0x12" + register "sar_threshold[2]" = "0x26" + register "sar_threshold[3]" = "0x73" + register "sar_hysteresis" = "0" + register "sar_voltage" = "6" + register "sar_compare_time" = "1" # 1us + register "sar_sampling_time" = "1" # 4us + register "short_key_debounce" = "3" # 30ms + register "jack_insert_debounce" = "7" # 512ms + register "jack_eject_debounce" = "0" + device i2c 1a on end + end + chip drivers/i2c/generic + register "hid" = ""INT343B"" + register "desc" = ""SSM4567 Left Speaker Amp"" + register "uid" = "0" + register "device_present_gpio" = "GPP_E3" + device i2c 34 on end + end + chip drivers/i2c/generic + register "hid" = ""INT343B"" + register "desc" = ""SSM4567 Right Speaker Amp"" + register "uid" = "1" + register "device_present_gpio" = "GPP_E3" + device i2c 35 on end + end + end # I2C #4 + device pci 1e.6 on end # SDCard + device pci 1f.3 on + chip drivers/generic/max98357a + register "hid" = ""MX98357A"" + register "sdmode_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_E3)" + register "device_present_gpio" = "GPP_E3" + register "device_present_gpio_invert" = "1" + register "sdmode_delay" = "5" + device generic 0 on end + end + end # Intel HDA + end +end |