summaryrefslogtreecommitdiff
path: root/src/mainboard
diff options
context:
space:
mode:
Diffstat (limited to 'src/mainboard')
-rw-r--r--src/mainboard/google/brya/variants/glassway/overridetree.cb494
1 files changed, 492 insertions, 2 deletions
diff --git a/src/mainboard/google/brya/variants/glassway/overridetree.cb b/src/mainboard/google/brya/variants/glassway/overridetree.cb
index 4f2c04a57a..ddeff20e51 100644
--- a/src/mainboard/google/brya/variants/glassway/overridetree.cb
+++ b/src/mainboard/google/brya/variants/glassway/overridetree.cb
@@ -1,6 +1,496 @@
+fw_config
+ field THERMAL_SOLUTION 0
+ option THERMAL_SOLUTION_PASSIVE 0
+ option THERMAL_SOLUTION_ACTIVE 1
+ end
+ field DB_USB 5 7
+ option DB_NONE 0
+ option DB_1C 1
+ option DB_1A 2
+ option DB_1C_1A 3
+ end
+ field SD_CARD 8
+ option SD_ABSENT 0
+ option SD_GL9750S 1
+ end
+ field TOUCHSCREEN_SOURCE 32 33
+ option TOUCHSCREEN_UNPROVISIONED 0
+ option TOUCHSCREEN_ELAN0001 1
+ option TOUCHSCREEN_ELAN9008 2
+ end
+end
+
chip soc/intel/alderlake
+ register "sagv" = "SaGv_Enabled"
+
+ # SOC Aux orientation override:
+ # This is a bitfield that corresponds to up to 4 TCSS ports.
+ # Bits (0,1) allocated for TCSS Port1 configuration and Bits (2,3)for TCSS Port2.
+ # TcssAuxOri = 0101b
+ # Bit0,Bit2 set to "1" indicates no retimer on USBC Ports
+ # Bit1,Bit3 set to "0" indicates Aux lines are not swapped on the
+ # motherboard to USBC connector
+ register "tcss_aux_ori" = "5"
+
+ register "typec_aux_bias_pads[0]" = "{.pad_auxp_dc = GPP_E22, .pad_auxn_dc = GPP_E23}"
+ register "typec_aux_bias_pads[1]" = "{.pad_auxp_dc = GPP_A21, .pad_auxn_dc = GPP_A22}"
+
+ register "usb2_ports[9]" = "USB2_PORT_MID(OC_SKIP)" # Bluetooth port for CNVi WLAN
+
+ # Configure external V1P05/Vnn/VnnSx Rails
+ register "ext_fivr_settings" = "{
+ .configure_ext_fivr = 1,
+ .v1p05_enable_bitmap = FIVR_ENABLE_ALL_SX & ~FIVR_ENABLE_S0,
+ .vnn_enable_bitmap = FIVR_ENABLE_ALL_SX,
+ .vnn_sx_enable_bitmap = FIVR_ENABLE_ALL_SX,
+ .v1p05_supported_voltage_bitmap = FIVR_VOLTAGE_NORMAL,
+ .vnn_supported_voltage_bitmap = FIVR_VOLTAGE_MIN_ACTIVE,
+ .v1p05_voltage_mv = 1050,
+ .vnn_voltage_mv = 780,
+ .vnn_sx_voltage_mv = 1050,
+ .v1p05_icc_max_ma = 500,
+ .vnn_icc_max_ma = 500,
+ }"
+
+ # Enable the Cnvi BT Audio Offload
+ register "cnvi_bt_audio_offload" = "1"
+
+ # Intel Common SoC Config
+ #+-------------------+---------------------------+
+ #| Field | Value |
+ #+-------------------+---------------------------+
+ #| I2C0 | TPM. Early init is |
+ #| | required to set up a BAR |
+ #| | for TPM communication |
+ #| I2C1 | Touchscreen |
+ #| I2C2 | Sub-board(PSensor)/WCAM |
+ #| I2C3 | Audio |
+ #| I2C5 | Trackpad |
+ #+-------------------+---------------------------+
+ register "common_soc_config" = "{
+ .i2c[0] = {
+ .early_init = 1,
+ .speed = I2C_SPEED_FAST_PLUS,
+ .speed_config[0] = {
+ .speed = I2C_SPEED_FAST_PLUS,
+ .scl_lcnt = 55,
+ .scl_hcnt = 30,
+ .sda_hold = 7,
+ }
+ },
+ .i2c[1] = {
+ .speed = I2C_SPEED_FAST,
+ .speed_config[0] = {
+ .speed = I2C_SPEED_FAST,
+ .scl_lcnt = 157,
+ .scl_hcnt = 79,
+ .sda_hold = 7,
+ }
+ },
+ .i2c[2] = {
+ .speed = I2C_SPEED_FAST,
+ .speed_config[0] = {
+ .speed = I2C_SPEED_FAST,
+ .scl_lcnt = 157,
+ .scl_hcnt = 79,
+ .sda_hold = 7,
+ }
+ },
+ .i2c[3] = {
+ .speed = I2C_SPEED_FAST,
+ .speed_config[0] = {
+ .speed = I2C_SPEED_FAST,
+ .scl_lcnt = 158,
+ .scl_hcnt = 79,
+ .sda_hold = 7,
+ }
+ },
+ .i2c[5] = {
+ .speed = I2C_SPEED_FAST,
+ .speed_config[0] = {
+ .speed = I2C_SPEED_FAST,
+ .scl_lcnt = 158,
+ .scl_hcnt = 79,
+ .sda_hold = 7,
+ }
+ },
+ }"
+
+ device domain 0 on
+ device ref dtt on
+ chip drivers/intel/dptf
+ ## sensor information
+ register "options.tsr[0].desc" = ""Memory""
+ register "options.tsr[1].desc" = ""Charger""
+ register "options.tsr[2].desc" = ""Ambient""
+
+ # TODO: below values are initial reference values only
+ ## Passive Policy
+ register "policies.passive" = "{
+ [0] = DPTF_PASSIVE(CPU, CPU, 95, 5000),
+ [1] = DPTF_PASSIVE(CPU, TEMP_SENSOR_0, 75, 5000),
+ [2] = DPTF_PASSIVE(CHARGER, TEMP_SENSOR_1, 75, 5000),
+ [3] = DPTF_PASSIVE(CPU, TEMP_SENSOR_2, 75, 5000),
+ }"
+
+ ## Critical Policy
+ register "policies.critical" = "{
+ [0] = DPTF_CRITICAL(CPU, 105, SHUTDOWN),
+ [1] = DPTF_CRITICAL(TEMP_SENSOR_0, 85, SHUTDOWN),
+ [2] = DPTF_CRITICAL(TEMP_SENSOR_1, 85, SHUTDOWN),
+ [3] = DPTF_CRITICAL(TEMP_SENSOR_2, 85, SHUTDOWN),
+ }"
+
+ register "controls.power_limits" = "{
+ .pl1 = {
+ .min_power = 3000,
+ .max_power = 6000,
+ .time_window_min = 28 * MSECS_PER_SEC,
+ .time_window_max = 32 * MSECS_PER_SEC,
+ .granularity = 200
+ },
+ .pl2 = {
+ .min_power = 25000,
+ .max_power = 25000,
+ .time_window_min = 1,
+ .time_window_max = 1,
+ .granularity = 1000
+ }
+ }"
+
+ ## Charger Performance Control (Control, mA)
+ register "controls.charger_perf" = "{
+ [0] = { 255, 1700 },
+ [1] = { 24, 1500 },
+ [2] = { 16, 1000 },
+ [3] = { 8, 500 }
+ }"
+
+ device generic 0 on
+ probe THERMAL_SOLUTION THERMAL_SOLUTION_PASSIVE
+ end
+ end
+ chip drivers/intel/dptf
+ ## sensor information
+ register "options.tsr[0].desc" = ""Memory""
+ register "options.tsr[1].desc" = ""Charger""
+ register "options.tsr[2].desc" = ""Ambient""
+
+ # TODO: below values are initial reference values only
+ ## Active Policy
+ register "policies.active" = "{
+ [0] = {
+ .target = DPTF_CPU,
+ .thresholds = {
+ TEMP_PCT(85, 90),
+ TEMP_PCT(80, 80),
+ TEMP_PCT(75, 70),
+ TEMP_PCT(70, 50),
+ TEMP_PCT(65, 30),
+ }
+ },
+ [1] = {
+ .target = DPTF_TEMP_SENSOR_2,
+ .thresholds = {
+ TEMP_PCT(50, 90),
+ TEMP_PCT(48, 70),
+ TEMP_PCT(46, 60),
+ TEMP_PCT(43, 40),
+ TEMP_PCT(40, 30),
+ }
+ }
+ }"
+
+ # TODO: below values are initial reference values only
+ ## Passive Policy
+ register "policies.passive" = "{
+ [0] = DPTF_PASSIVE(CPU, CPU, 95, 5000),
+ [1] = DPTF_PASSIVE(CPU, TEMP_SENSOR_0, 75, 5000),
+ [2] = DPTF_PASSIVE(CHARGER, TEMP_SENSOR_1, 75, 5000),
+ [3] = DPTF_PASSIVE(CPU, TEMP_SENSOR_2, 75, 5000),
+ }"
+
+ ## Critical Policy
+ register "policies.critical" = "{
+ [0] = DPTF_CRITICAL(CPU, 105, SHUTDOWN),
+ [1] = DPTF_CRITICAL(TEMP_SENSOR_0, 85, SHUTDOWN),
+ [2] = DPTF_CRITICAL(TEMP_SENSOR_1, 85, SHUTDOWN),
+ [3] = DPTF_CRITICAL(TEMP_SENSOR_2, 85, SHUTDOWN),
+ }"
+
+ register "controls.power_limits" = "{
+ .pl1 = {
+ .min_power = 12000,
+ .max_power = 15000,
+ .time_window_min = 28 * MSECS_PER_SEC,
+ .time_window_max = 32 * MSECS_PER_SEC,
+ .granularity = 200
+ },
+ .pl2 = {
+ .min_power = 35000,
+ .max_power = 35000,
+ .time_window_min = 1,
+ .time_window_max = 1,
+ .granularity = 1000
+ }
+ }"
+
+ ## Charger Performance Control (Control, mA)
+ register "controls.charger_perf" = "{
+ [0] = { 255, 1700 },
+ [1] = { 24, 1500 },
+ [2] = { 16, 1000 },
+ [3] = { 8, 500 }
+ }"
+
+ ## Fan Performance Control (Percent, Speed, Noise, Power)
+ register "controls.fan_perf" = "{
+ [0] = { 100, 6000, 220, 2200, },
+ [1] = { 92, 5500, 180, 1800, },
+ [2] = { 85, 5000, 145, 1450, },
+ [3] = { 70, 4400, 115, 1150, },
+ [4] = { 56, 3900, 90, 900, },
+ [5] = { 45, 3300, 55, 550, },
+ [6] = { 38, 3000, 30, 300, },
+ [7] = { 33, 2900, 15, 150, },
+ [8] = { 10, 800, 10, 100, },
+ [9] = { 0, 0, 0, 50, }
+ }"
- device domain 0 on
- end
+ ## Fan options
+ register "options.fan.fine_grained_control" = "1"
+ register "options.fan.step_size" = "2"
+ device generic 1 on
+ probe THERMAL_SOLUTION THERMAL_SOLUTION_ACTIVE
+ end
+ end
+ end
+ device ref cnvi_wifi on
+ chip drivers/wifi/generic
+ register "enable_cnvi_ddr_rfim" = "true"
+ device generic 0 on end
+ end
+ end
+ device ref i2c1 on
+ chip drivers/i2c/generic
+ register "hid" = ""ELAN0001""
+ register "desc" = ""ELAN Touchscreen""
+ register "irq" = "ACPI_IRQ_LEVEL_LOW(GPP_C7_IRQ)"
+ register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C1)"
+ register "reset_delay_ms" = "25"
+ register "reset_off_delay_ms" = "4"
+ register "stop_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C6)"
+ register "stop_delay_ms" = "25"
+ register "stop_off_delay_ms" = "2"
+ register "enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_C0)"
+ register "enable_delay_ms" = "7"
+ register "has_power_resource" = "1"
+ device i2c 10 on
+ probe TOUCHSCREEN_SOURCE TOUCHSCREEN_UNPROVISIONED
+ probe TOUCHSCREEN_SOURCE TOUCHSCREEN_ELAN0001
+ end
+ end
+ chip drivers/i2c/hid
+ register "generic.hid" = ""ELAN9008""
+ register "generic.desc" = ""ELAN Touchscreen""
+ register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPP_C7_IRQ)"
+ register "generic.detect" = "1"
+ register "generic.reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C1)"
+ register "generic.reset_delay_ms" = "20"
+ register "generic.reset_off_delay_ms" = "2"
+ register "generic.stop_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C6)"
+ register "generic.stop_delay_ms" = "280"
+ register "generic.stop_off_delay_ms" = "2"
+ register "generic.enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_C0)"
+ register "generic.enable_delay_ms" = "1"
+ register "generic.has_power_resource" = "1"
+ register "hid_desc_reg_offset" = "0x01"
+ device i2c 10 on
+ probe TOUCHSCREEN_SOURCE TOUCHSCREEN_ELAN9008
+ end
+ end
+ end #I2C1
+ device ref i2c3 on
+ chip drivers/i2c/generic
+ register "hid" = ""RTL5682""
+ register "name" = ""RT58""
+ register "desc" = ""Headset Codec""
+ register "irq_gpio" = "ACPI_GPIO_IRQ_EDGE_BOTH(GPP_A23)"
+ # Set the jd_src to RT5668_JD1 for jack detection
+ register "property_count" = "1"
+ register "property_list[0].type" = "ACPI_DP_TYPE_INTEGER"
+ register "property_list[0].name" = ""realtek,jd-src""
+ register "property_list[0].integer" = "1"
+ device i2c 1a on end
+ end
+ chip drivers/generic/alc1015
+ register "hid" = ""RTL1019""
+ register "sdb" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_A11)"
+ device generic 1 on end
+ end
+ end #I2C3
+ device ref i2c5 on
+ chip drivers/i2c/generic
+ register "hid" = ""ELAN0000""
+ register "desc" = ""ELAN Touchpad""
+ register "irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_F14_IRQ)"
+ register "wake" = "GPE0_DW2_14"
+ register "detect" = "1"
+ device i2c 15 on end
+ end
+ end #I2C5
+ device ref pcie_rp4 on
+ # Enable wlan PCIe 4 using clk 2
+ register "pch_pcie_rp[PCH_RP(4)]" = "{
+ .clk_src = 2,
+ .clk_req = 2,
+ .flags = PCIE_RP_LTR | PCIE_RP_AER,
+ }"
+ chip drivers/wifi/generic
+ register "add_acpi_dma_property" = "true"
+ device pci 00.0 on end
+ end
+ end
+ device ref pcie_rp7 on
+ # Enable SD Card PCIe 7 using clk 3
+ register "pch_pcie_rp[PCH_RP(7)]" = "{
+ .clk_src = 3,
+ .clk_req = 3,
+ .flags = PCIE_RP_HOTPLUG | PCIE_RP_LTR | PCIE_RP_AER,
+ }"
+ chip soc/intel/common/block/pcie/rtd3
+ register "enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_H13)"
+ register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_H12)"
+ register "srcclk_pin" = "3"
+ device generic 0 on end
+ end
+ probe SD_CARD SD_GL9750S
+ end
+ device ref emmc on
+ probe STORAGE STORAGE_EMMC
+ end
+ device ref ish on
+ chip drivers/intel/ish
+ register "add_acpi_dma_property" = "true"
+ device generic 0 on end
+ end
+ probe STORAGE STORAGE_UFS
+ end
+ device ref ufs on
+ probe STORAGE STORAGE_UFS
+ end
+ device ref pch_espi on
+ chip ec/google/chromeec
+ use conn0 as mux_conn[0]
+ use conn1 as mux_conn[1]
+ device pnp 0c09.0 on end
+ end
+ end
+ device ref pmc hidden
+ chip drivers/intel/pmc_mux
+ device generic 0 on
+ chip drivers/intel/pmc_mux/conn
+ use usb2_port1 as usb2_port
+ use tcss_usb3_port1 as usb3_port
+ device generic 0 alias conn0 on end
+ end
+ chip drivers/intel/pmc_mux/conn
+ use usb2_port2 as usb2_port
+ use tcss_usb3_port2 as usb3_port
+ device generic 1 alias conn1 on end
+ end
+ end
+ end
+ end
+ device ref tcss_xhci on
+ chip drivers/usb/acpi
+ device ref tcss_root_hub on
+ chip drivers/usb/acpi
+ register "desc" = ""USB3 Type-C Port C0 (MLB)""
+ register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
+ register "use_custom_pld" = "true"
+ register "custom_pld" = "ACPI_PLD_TYPE_C(LEFT, LEFT, ACPI_PLD_GROUP(1, 1))"
+ device ref tcss_usb3_port1 on end
+ end
+ chip drivers/usb/acpi
+ register "desc" = ""USB3 Type-C Port C1 (DB)""
+ register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
+ register "use_custom_pld" = "true"
+ register "custom_pld" = "ACPI_PLD_TYPE_C(RIGHT, RIGHT, ACPI_PLD_GROUP(2, 1))"
+ device ref tcss_usb3_port2 on end
+ end
+ end
+ end
+ end
+ device ref xhci on
+ chip drivers/usb/acpi
+ device ref xhci_root_hub on
+ chip drivers/usb/acpi
+ register "desc" = ""USB2 Type-C Port C0 (MLB)""
+ register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
+ register "use_custom_pld" = "true"
+ register "custom_pld" = "ACPI_PLD_TYPE_C(LEFT, LEFT, ACPI_PLD_GROUP(1, 1))"
+ device ref usb2_port1 on end
+ end
+ chip drivers/usb/acpi
+ register "desc" = ""USB2 Type-C Port C1 (DB)""
+ register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
+ register "use_custom_pld" = "true"
+ register "custom_pld" = "ACPI_PLD_TYPE_C(RIGHT, RIGHT, ACPI_PLD_GROUP(2, 1))"
+ device ref usb2_port2 on end
+ end
+ chip drivers/usb/acpi
+ register "desc" = ""USB2 Type-A Port A0 (MLB)""
+ register "type" = "UPC_TYPE_A"
+ register "use_custom_pld" = "true"
+ register "custom_pld" = "ACPI_PLD_TYPE_A(LEFT, RIGHT, ACPI_PLD_GROUP(3, 1))"
+ device ref usb2_port3 on end
+ end
+ chip drivers/usb/acpi
+ register "desc" = ""USB2 Type-A Port A1 (DB)""
+ register "type" = "UPC_TYPE_A"
+ register "use_custom_pld" = "true"
+ register "custom_pld" = "ACPI_PLD_TYPE_A(RIGHT, LEFT, ACPI_PLD_GROUP(4, 1))"
+ device ref usb2_port4 on
+ probe DB_USB DB_1C_1A
+ end
+ end
+ chip drivers/usb/acpi
+ register "desc" = ""USB2 Camera""
+ register "type" = "UPC_TYPE_INTERNAL"
+ device ref usb2_port6 on end
+ end
+ chip drivers/usb/acpi
+ register "desc" = ""USB2 Camera""
+ register "type" = "UPC_TYPE_INTERNAL"
+ device ref usb2_port7 on end
+ end
+ chip drivers/usb/acpi
+ register "desc" = ""USB2 Bluetooth""
+ register "type" = "UPC_TYPE_INTERNAL"
+ register "reset_gpio" =
+ "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D4)"
+ device ref usb2_port8 on end
+ end
+ chip drivers/usb/acpi
+ register "desc" = ""USB3 Type-A Port A0 (MLB)""
+ register "type" = "UPC_TYPE_USB3_A"
+ register "use_custom_pld" = "true"
+ register "custom_pld" = "ACPI_PLD_TYPE_A(LEFT, RIGHT, ACPI_PLD_GROUP(3, 1))"
+ device ref usb3_port1 on end
+ end
+ chip drivers/usb/acpi
+ register "desc" = ""USB3 Type-A Port A1 (DB)""
+ register "type" = "UPC_TYPE_USB3_A"
+ register "use_custom_pld" = "true"
+ register "custom_pld" = "ACPI_PLD_TYPE_A(RIGHT, LEFT, ACPI_PLD_GROUP(4, 1))"
+ device ref usb3_port2 on
+ probe DB_USB DB_1C_1A
+ end
+ end
+ end
+ end
+ end
+ end
end
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-10 14:02:28 +0000