summaryrefslogtreecommitdiff
path: root/src/mainboard
diff options
context:
space:
mode:
Diffstat (limited to 'src/mainboard')
-rw-r--r--src/mainboard/asus/m2v-mx_se/Options.lb2
-rw-r--r--src/mainboard/dell/s1850/irq_tables.c96
-rw-r--r--src/mainboard/msi/ms9185/Options.lb2
-rw-r--r--src/mainboard/msi/ms9282/Options.lb4
-rw-r--r--src/mainboard/rca/rm4100/gpio.c286
-rw-r--r--src/mainboard/thomson/ip1000/gpio.c286
6 files changed, 338 insertions, 338 deletions
diff --git a/src/mainboard/asus/m2v-mx_se/Options.lb b/src/mainboard/asus/m2v-mx_se/Options.lb
index 93c1bd32e6..5d74fbce22 100644
--- a/src/mainboard/asus/m2v-mx_se/Options.lb
+++ b/src/mainboard/asus/m2v-mx_se/Options.lb
@@ -94,7 +94,7 @@ uses SB_HT_CHAIN_UNITID_OFFSET_ONLY
uses SB_HT_CHAIN_ON_BUS0
uses CONFIG_COMPRESSED_PAYLOAD_NRV2B
uses CONFIG_COMPRESSED_PAYLOAD_LZMA
-uses CONFIG_USE_PRINTK_IN_CAR
+uses CONFIG_USE_PRINTK_IN_CAR
default ROM_SIZE = 512 * 1024
default FALLBACK_SIZE = 256 * 1024
diff --git a/src/mainboard/dell/s1850/irq_tables.c b/src/mainboard/dell/s1850/irq_tables.c
index d0e7be1cd9..dc5514bbac 100644
--- a/src/mainboard/dell/s1850/irq_tables.c
+++ b/src/mainboard/dell/s1850/irq_tables.c
@@ -1,48 +1,48 @@
-/* This file was generated by getpir.c, do not modify!
- (but if you do, please run checkpir on it to verify)
- * Contains the IRQ Routing Table dumped directly from your memory, which BIOS sets up
- *
- * Documentation at : http://www.microsoft.com/hwdev/busbios/PCIIRQ.HTM
-*/
-
-#include <arch/pirq_routing.h>
-
-const struct irq_routing_table intel_irq_routing_table = {
- PIRQ_SIGNATURE, /* u32 signature */
- PIRQ_VERSION, /* u16 version */
- 32+16*17, /* there can be total 17 devices on the bus */
- 0x00, /* Where the interrupt router lies (bus) */
- (0x1f<<3)|0x0, /* Where the interrupt router lies (dev) */
- 0, /* IRQs devoted exclusively to PCI usage */
- 0x8086, /* Vendor */
- 0x24d0, /* Device */
- 0, /* Crap (miniport) */
- { 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 }, /* u8 rfu[11] */
- 0xc4, /* u8 checksum , this hase to set to some value that would give 0 after the sum of all bytes for this structure (including checksum) */
- {
- /* bus, dev|fn, {link, bitmap}, {link, bitmap}, {link, bitmap}, {link, bitmap}, slot, rfu */
- {0x00,(0x02<<3)|0x0, {{0x60, 0xccf8}, {0x00, 0x0000}, {0x00, 0x0000}, {0x00, 0x00000}}, 0x0, 0x0},
- {0x00,(0x04<<3)|0x0, {{0x60, 0xccf8}, {0x00, 0x0000}, {0x00, 0x0000}, {0x00, 0x00000}}, 0x0, 0x0},
- {0x00,(0x05<<3)|0x0, {{0x60, 0xccf8}, {0x00, 0x0000}, {0x00, 0x0000}, {0x00, 0x00000}}, 0x0, 0x0},
- {0x00,(0x06<<3)|0x0, {{0x60, 0xccf8}, {0x00, 0x0000}, {0x00, 0x0000}, {0x00, 0x00000}}, 0x0, 0x0},
- {0x05,(0x00<<3)|0x0, {{0x60, 0xccf8}, {0x61, 0xccf8}, {0x62, 0xccf8}, {0x63, 0x0ccf8}}, 0x0, 0x0},
- {0x01,(0x00<<3)|0x0, {{0x60, 0xccf8}, {0x61, 0xccf8}, {0x62, 0xccf8}, {0x63, 0x0ccf8}}, 0x0, 0x0},
- {0x00,(0x1d<<3)|0x0, {{0x60, 0xccf8}, {0x63, 0xccf8}, {0x62, 0xccf8}, {0x6b, 0x0ccf8}}, 0x0, 0x0},
- {0x09,(0x05<<3)|0x0, {{0x68, 0xccf8}, {0x69, 0xccf8}, {0x00, 0x0000}, {0x00, 0x00000}}, 0x0, 0x0},
- {0x09,(0x06<<3)|0x0, {{0x6b, 0xccf8}, {0x00, 0x0000}, {0x00, 0x0000}, {0x00, 0x00000}}, 0x0, 0x0},
- {0x09,(0x0d<<3)|0x0, {{0x62, 0xccf8}, {0x00, 0x0000}, {0x00, 0x0000}, {0x00, 0x00000}}, 0x0, 0x0},
- {0x09,(0x03<<3)|0x0, {{0x63, 0xccf8}, {0x63, 0xccf8}, {0x63, 0xccf8}, {0x63, 0x0ccf8}}, 0x0, 0x0},
- {0x06,(0x07<<3)|0x0, {{0x60, 0xccf8}, {0x00, 0x0000}, {0x00, 0x0000}, {0x00, 0x00000}}, 0x0, 0x0},
- {0x07,(0x08<<3)|0x0, {{0x61, 0xccf8}, {0x00, 0x0000}, {0x00, 0x0000}, {0x00, 0x00000}}, 0x0, 0x0},
- {0x02,(0x05<<3)|0x0, {{0x62, 0xccf8}, {0x00, 0x0000}, {0x00, 0x0000}, {0x00, 0x00000}}, 0x0, 0x0},
- {0x04,(0x00<<3)|0x0, {{0x60, 0xccf8}, {0x61, 0xccf8}, {0x62, 0xccf8}, {0x63, 0x0ccf8}}, 0x1, 0x0},
- {0x08,(0x00<<3)|0x0, {{0x60, 0xccf8}, {0x61, 0xccf8}, {0x62, 0xccf8}, {0x63, 0x0ccf8}}, 0x2, 0x0},
- {0x02,(0x0e<<3)|0x0, {{0x62, 0xccf8}, {0x00, 0x0000}, {0x00, 0x0000}, {0x00, 0x00000}}, 0x0, 0x0},
- }
-};
-
-unsigned long write_pirq_routing_table(unsigned long addr)
-{
- return copy_pirq_routing_table(addr);
-}
-
+/* This file was generated by getpir.c, do not modify!
+ (but if you do, please run checkpir on it to verify)
+ * Contains the IRQ Routing Table dumped directly from your memory, which BIOS sets up
+ *
+ * Documentation at : http://www.microsoft.com/hwdev/busbios/PCIIRQ.HTM
+*/
+
+#include <arch/pirq_routing.h>
+
+const struct irq_routing_table intel_irq_routing_table = {
+ PIRQ_SIGNATURE, /* u32 signature */
+ PIRQ_VERSION, /* u16 version */
+ 32+16*17, /* there can be total 17 devices on the bus */
+ 0x00, /* Where the interrupt router lies (bus) */
+ (0x1f<<3)|0x0, /* Where the interrupt router lies (dev) */
+ 0, /* IRQs devoted exclusively to PCI usage */
+ 0x8086, /* Vendor */
+ 0x24d0, /* Device */
+ 0, /* Crap (miniport) */
+ { 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 }, /* u8 rfu[11] */
+ 0xc4, /* u8 checksum , this hase to set to some value that would give 0 after the sum of all bytes for this structure (including checksum) */
+ {
+ /* bus, dev|fn, {link, bitmap}, {link, bitmap}, {link, bitmap}, {link, bitmap}, slot, rfu */
+ {0x00,(0x02<<3)|0x0, {{0x60, 0xccf8}, {0x00, 0x0000}, {0x00, 0x0000}, {0x00, 0x00000}}, 0x0, 0x0},
+ {0x00,(0x04<<3)|0x0, {{0x60, 0xccf8}, {0x00, 0x0000}, {0x00, 0x0000}, {0x00, 0x00000}}, 0x0, 0x0},
+ {0x00,(0x05<<3)|0x0, {{0x60, 0xccf8}, {0x00, 0x0000}, {0x00, 0x0000}, {0x00, 0x00000}}, 0x0, 0x0},
+ {0x00,(0x06<<3)|0x0, {{0x60, 0xccf8}, {0x00, 0x0000}, {0x00, 0x0000}, {0x00, 0x00000}}, 0x0, 0x0},
+ {0x05,(0x00<<3)|0x0, {{0x60, 0xccf8}, {0x61, 0xccf8}, {0x62, 0xccf8}, {0x63, 0x0ccf8}}, 0x0, 0x0},
+ {0x01,(0x00<<3)|0x0, {{0x60, 0xccf8}, {0x61, 0xccf8}, {0x62, 0xccf8}, {0x63, 0x0ccf8}}, 0x0, 0x0},
+ {0x00,(0x1d<<3)|0x0, {{0x60, 0xccf8}, {0x63, 0xccf8}, {0x62, 0xccf8}, {0x6b, 0x0ccf8}}, 0x0, 0x0},
+ {0x09,(0x05<<3)|0x0, {{0x68, 0xccf8}, {0x69, 0xccf8}, {0x00, 0x0000}, {0x00, 0x00000}}, 0x0, 0x0},
+ {0x09,(0x06<<3)|0x0, {{0x6b, 0xccf8}, {0x00, 0x0000}, {0x00, 0x0000}, {0x00, 0x00000}}, 0x0, 0x0},
+ {0x09,(0x0d<<3)|0x0, {{0x62, 0xccf8}, {0x00, 0x0000}, {0x00, 0x0000}, {0x00, 0x00000}}, 0x0, 0x0},
+ {0x09,(0x03<<3)|0x0, {{0x63, 0xccf8}, {0x63, 0xccf8}, {0x63, 0xccf8}, {0x63, 0x0ccf8}}, 0x0, 0x0},
+ {0x06,(0x07<<3)|0x0, {{0x60, 0xccf8}, {0x00, 0x0000}, {0x00, 0x0000}, {0x00, 0x00000}}, 0x0, 0x0},
+ {0x07,(0x08<<3)|0x0, {{0x61, 0xccf8}, {0x00, 0x0000}, {0x00, 0x0000}, {0x00, 0x00000}}, 0x0, 0x0},
+ {0x02,(0x05<<3)|0x0, {{0x62, 0xccf8}, {0x00, 0x0000}, {0x00, 0x0000}, {0x00, 0x00000}}, 0x0, 0x0},
+ {0x04,(0x00<<3)|0x0, {{0x60, 0xccf8}, {0x61, 0xccf8}, {0x62, 0xccf8}, {0x63, 0x0ccf8}}, 0x1, 0x0},
+ {0x08,(0x00<<3)|0x0, {{0x60, 0xccf8}, {0x61, 0xccf8}, {0x62, 0xccf8}, {0x63, 0x0ccf8}}, 0x2, 0x0},
+ {0x02,(0x0e<<3)|0x0, {{0x62, 0xccf8}, {0x00, 0x0000}, {0x00, 0x0000}, {0x00, 0x00000}}, 0x0, 0x0},
+ }
+};
+
+unsigned long write_pirq_routing_table(unsigned long addr)
+{
+ return copy_pirq_routing_table(addr);
+}
+
diff --git a/src/mainboard/msi/ms9185/Options.lb b/src/mainboard/msi/ms9185/Options.lb
index efd5dc95bc..5c3073e2d2 100644
--- a/src/mainboard/msi/ms9185/Options.lb
+++ b/src/mainboard/msi/ms9185/Options.lb
@@ -220,7 +220,7 @@ default USE_DCACHE_RAM=1
default DCACHE_RAM_BASE=0xcc000
default DCACHE_RAM_SIZE=0x04000
default DCACHE_RAM_GLOBAL_VAR_SIZE=0x01000
-default CONFIG_USE_INIT=0
+default CONFIG_USE_INIT=0
##
## Build code to setup a generic IOAPIC
diff --git a/src/mainboard/msi/ms9282/Options.lb b/src/mainboard/msi/ms9282/Options.lb
index a666a8c61e..1a686826cd 100644
--- a/src/mainboard/msi/ms9282/Options.lb
+++ b/src/mainboard/msi/ms9282/Options.lb
@@ -100,7 +100,7 @@ uses SB_HT_CHAIN_ON_BUS0
uses CONFIG_COMPRESSED_PAYLOAD_LZMA
uses CONFIG_COMPRESSED_PAYLOAD_NRV2B
uses CONFIG_PRECOMPRESSED_PAYLOAD
-uses CONFIG_USE_PRINTK_IN_CAR
+uses CONFIG_USE_PRINTK_IN_CAR
## ROM_SIZE is the size of boot ROM that this board will use.
#512K bytes
@@ -265,7 +265,7 @@ default CONFIG_GDB_STUB=0
## The Serial Console
##
default CONFIG_USE_PRINTK_IN_CAR=1
-
+
# To Enable the Serial Console
default CONFIG_CONSOLE_SERIAL8250=1
diff --git a/src/mainboard/rca/rm4100/gpio.c b/src/mainboard/rca/rm4100/gpio.c
index 97231e52a0..d51bc90e78 100644
--- a/src/mainboard/rca/rm4100/gpio.c
+++ b/src/mainboard/rca/rm4100/gpio.c
@@ -1,143 +1,143 @@
-/*
- * This file is part of the coreboot project.
- *
- * Copyright (C) 2008 Joseph Smith <joe@settoplinux.org>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
- */
-
-#define PME_DEV PNP_DEV(0x2e, 0x0a)
-#define PME_IO_BASE_ADDR 0x800 /* Runtime register base address */
-#define ICH_IO_BASE_ADDR 0x00000500 /* GPIO base address register */
-
-/* Early mainboard specific GPIO setup. */
-static void mb_gpio_init(void)
-{
- device_t dev;
- uint16_t port;
- uint32_t set_gpio;
-
- /* Southbridge GPIOs. */
- /* Set the LPC device statically. */
- dev = PCI_DEV(0x0, 0x1f, 0x0);
-
- /* Set the value for GPIO base address register and enable GPIO. */
- pci_write_config32(dev, GPIO_BASE_ICH0_5, (ICH_IO_BASE_ADDR | 1));
- pci_write_config8(dev, GPIO_CNTL_ICH0_5, 0x10);
-
- /* Set GPIO23 to high, this enables the LAN controller. */
- udelay(10);
- set_gpio = inl(ICH_IO_BASE_ADDR + 0x0c);
- set_gpio |= 1 << 23;
- outl(set_gpio, ICH_IO_BASE_ADDR + 0x0c);
-
- /* Super I/O GPIOs. */
- dev = PME_DEV;
- port = dev >> 8;
-
- /* Enter the configuration state. */
- outb(0x55, port);
- pnp_set_logical_device(dev);
- pnp_set_enable(dev, 0);
- pnp_set_iobase(dev, PNP_IDX_IO0, PME_IO_BASE_ADDR);
- pnp_set_enable(dev, 1);
-
- /* GP21 - LED_RED */
- outl(0x01, PME_IO_BASE_ADDR + 0x2c);
-
- /* GP30 - FAN2_TACH */
- outl(0x05, PME_IO_BASE_ADDR + 0x33);
-
- /* GP31 - FAN1_TACH */
- outl(0x05, PME_IO_BASE_ADDR + 0x34);
-
- /* GP32 - FAN2_CTRL */
- outl(0x04, PME_IO_BASE_ADDR + 0x35);
-
- /* GP33 - FAN1_CTRL */
- outl(0x04, PME_IO_BASE_ADDR + 0x36);
-
- /* GP34 - AUD_MUTE_OUT_R */
- outl(0x00, PME_IO_BASE_ADDR + 0x37);
-
- /* GP36 - KBRST */
- outl(0x00, PME_IO_BASE_ADDR + 0x39);
-
- /* GP37 - A20GATE */
- outl(0x00, PME_IO_BASE_ADDR + 0x3a);
-
- /* GP42 - GPIO_PME_OUT */
- outl(0x00, PME_IO_BASE_ADDR + 0x3d);
-
- /* GP50 - SER2_RI */
- outl(0x05, PME_IO_BASE_ADDR + 0x3f);
-
- /* GP51 - SER2_DCD */
- outl(0x05, PME_IO_BASE_ADDR + 0x40);
-
- /* GP52 - SER2_RX */
- outl(0x05, PME_IO_BASE_ADDR + 0x41);
-
- /* GP53 - SER2_TX */
- outl(0x04, PME_IO_BASE_ADDR + 0x42);
-
- /* GP55 - SER2_RTS */
- outl(0x04, PME_IO_BASE_ADDR + 0x44);
-
- /* GP56 - SER2_CTS */
- outl(0x05, PME_IO_BASE_ADDR + 0x45);
-
- /* GP57 - SER2_DTR */
- outl(0x04, PME_IO_BASE_ADDR + 0x46);
-
- /* GP60 - LED_GREEN */
- outl(0x01, PME_IO_BASE_ADDR + 0x47);
-
- /* GP61 - LED_YELLOW */
- outl(0x01, PME_IO_BASE_ADDR + 0x48);
-
- /* GP3 */
- outl(0xc0, PME_IO_BASE_ADDR + 0x4d);
-
- /* GP4 */
- outl(0x04, PME_IO_BASE_ADDR + 0x4e);
-
- /* FAN1 */
- outl(0x01, PME_IO_BASE_ADDR + 0x56);
-
- /* FAN2 */
- outl(0x01, PME_IO_BASE_ADDR + 0x57);
-
- /* Fan Control */
- outl(0x50, PME_IO_BASE_ADDR + 0x58);
-
- /* Fan1 Tachometer */
- outl(0xff, PME_IO_BASE_ADDR + 0x59);
-
- /* Fan2 Tachometer */
- outl(0xff, PME_IO_BASE_ADDR + 0x5a);
-
- /* LED1 */
- outl(0x00, PME_IO_BASE_ADDR + 0x5d);
-
- /* LED2 */
- outl(0x00, PME_IO_BASE_ADDR + 0x5e);
-
- /* Keyboard Scan Code */
- outl(0x00, PME_IO_BASE_ADDR + 0x5f);
-
- /* Exit the configuration state. */
- outb(0xaa, port);
-}
+/*
+ * This file is part of the coreboot project.
+ *
+ * Copyright (C) 2008 Joseph Smith <joe@settoplinux.org>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+#define PME_DEV PNP_DEV(0x2e, 0x0a)
+#define PME_IO_BASE_ADDR 0x800 /* Runtime register base address */
+#define ICH_IO_BASE_ADDR 0x00000500 /* GPIO base address register */
+
+/* Early mainboard specific GPIO setup. */
+static void mb_gpio_init(void)
+{
+ device_t dev;
+ uint16_t port;
+ uint32_t set_gpio;
+
+ /* Southbridge GPIOs. */
+ /* Set the LPC device statically. */
+ dev = PCI_DEV(0x0, 0x1f, 0x0);
+
+ /* Set the value for GPIO base address register and enable GPIO. */
+ pci_write_config32(dev, GPIO_BASE_ICH0_5, (ICH_IO_BASE_ADDR | 1));
+ pci_write_config8(dev, GPIO_CNTL_ICH0_5, 0x10);
+
+ /* Set GPIO23 to high, this enables the LAN controller. */
+ udelay(10);
+ set_gpio = inl(ICH_IO_BASE_ADDR + 0x0c);
+ set_gpio |= 1 << 23;
+ outl(set_gpio, ICH_IO_BASE_ADDR + 0x0c);
+
+ /* Super I/O GPIOs. */
+ dev = PME_DEV;
+ port = dev >> 8;
+
+ /* Enter the configuration state. */
+ outb(0x55, port);
+ pnp_set_logical_device(dev);
+ pnp_set_enable(dev, 0);
+ pnp_set_iobase(dev, PNP_IDX_IO0, PME_IO_BASE_ADDR);
+ pnp_set_enable(dev, 1);
+
+ /* GP21 - LED_RED */
+ outl(0x01, PME_IO_BASE_ADDR + 0x2c);
+
+ /* GP30 - FAN2_TACH */
+ outl(0x05, PME_IO_BASE_ADDR + 0x33);
+
+ /* GP31 - FAN1_TACH */
+ outl(0x05, PME_IO_BASE_ADDR + 0x34);
+
+ /* GP32 - FAN2_CTRL */
+ outl(0x04, PME_IO_BASE_ADDR + 0x35);
+
+ /* GP33 - FAN1_CTRL */
+ outl(0x04, PME_IO_BASE_ADDR + 0x36);
+
+ /* GP34 - AUD_MUTE_OUT_R */
+ outl(0x00, PME_IO_BASE_ADDR + 0x37);
+
+ /* GP36 - KBRST */
+ outl(0x00, PME_IO_BASE_ADDR + 0x39);
+
+ /* GP37 - A20GATE */
+ outl(0x00, PME_IO_BASE_ADDR + 0x3a);
+
+ /* GP42 - GPIO_PME_OUT */
+ outl(0x00, PME_IO_BASE_ADDR + 0x3d);
+
+ /* GP50 - SER2_RI */
+ outl(0x05, PME_IO_BASE_ADDR + 0x3f);
+
+ /* GP51 - SER2_DCD */
+ outl(0x05, PME_IO_BASE_ADDR + 0x40);
+
+ /* GP52 - SER2_RX */
+ outl(0x05, PME_IO_BASE_ADDR + 0x41);
+
+ /* GP53 - SER2_TX */
+ outl(0x04, PME_IO_BASE_ADDR + 0x42);
+
+ /* GP55 - SER2_RTS */
+ outl(0x04, PME_IO_BASE_ADDR + 0x44);
+
+ /* GP56 - SER2_CTS */
+ outl(0x05, PME_IO_BASE_ADDR + 0x45);
+
+ /* GP57 - SER2_DTR */
+ outl(0x04, PME_IO_BASE_ADDR + 0x46);
+
+ /* GP60 - LED_GREEN */
+ outl(0x01, PME_IO_BASE_ADDR + 0x47);
+
+ /* GP61 - LED_YELLOW */
+ outl(0x01, PME_IO_BASE_ADDR + 0x48);
+
+ /* GP3 */
+ outl(0xc0, PME_IO_BASE_ADDR + 0x4d);
+
+ /* GP4 */
+ outl(0x04, PME_IO_BASE_ADDR + 0x4e);
+
+ /* FAN1 */
+ outl(0x01, PME_IO_BASE_ADDR + 0x56);
+
+ /* FAN2 */
+ outl(0x01, PME_IO_BASE_ADDR + 0x57);
+
+ /* Fan Control */
+ outl(0x50, PME_IO_BASE_ADDR + 0x58);
+
+ /* Fan1 Tachometer */
+ outl(0xff, PME_IO_BASE_ADDR + 0x59);
+
+ /* Fan2 Tachometer */
+ outl(0xff, PME_IO_BASE_ADDR + 0x5a);
+
+ /* LED1 */
+ outl(0x00, PME_IO_BASE_ADDR + 0x5d);
+
+ /* LED2 */
+ outl(0x00, PME_IO_BASE_ADDR + 0x5e);
+
+ /* Keyboard Scan Code */
+ outl(0x00, PME_IO_BASE_ADDR + 0x5f);
+
+ /* Exit the configuration state. */
+ outb(0xaa, port);
+}
diff --git a/src/mainboard/thomson/ip1000/gpio.c b/src/mainboard/thomson/ip1000/gpio.c
index 97231e52a0..d51bc90e78 100644
--- a/src/mainboard/thomson/ip1000/gpio.c
+++ b/src/mainboard/thomson/ip1000/gpio.c
@@ -1,143 +1,143 @@
-/*
- * This file is part of the coreboot project.
- *
- * Copyright (C) 2008 Joseph Smith <joe@settoplinux.org>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
- */
-
-#define PME_DEV PNP_DEV(0x2e, 0x0a)
-#define PME_IO_BASE_ADDR 0x800 /* Runtime register base address */
-#define ICH_IO_BASE_ADDR 0x00000500 /* GPIO base address register */
-
-/* Early mainboard specific GPIO setup. */
-static void mb_gpio_init(void)
-{
- device_t dev;
- uint16_t port;
- uint32_t set_gpio;
-
- /* Southbridge GPIOs. */
- /* Set the LPC device statically. */
- dev = PCI_DEV(0x0, 0x1f, 0x0);
-
- /* Set the value for GPIO base address register and enable GPIO. */
- pci_write_config32(dev, GPIO_BASE_ICH0_5, (ICH_IO_BASE_ADDR | 1));
- pci_write_config8(dev, GPIO_CNTL_ICH0_5, 0x10);
-
- /* Set GPIO23 to high, this enables the LAN controller. */
- udelay(10);
- set_gpio = inl(ICH_IO_BASE_ADDR + 0x0c);
- set_gpio |= 1 << 23;
- outl(set_gpio, ICH_IO_BASE_ADDR + 0x0c);
-
- /* Super I/O GPIOs. */
- dev = PME_DEV;
- port = dev >> 8;
-
- /* Enter the configuration state. */
- outb(0x55, port);
- pnp_set_logical_device(dev);
- pnp_set_enable(dev, 0);
- pnp_set_iobase(dev, PNP_IDX_IO0, PME_IO_BASE_ADDR);
- pnp_set_enable(dev, 1);
-
- /* GP21 - LED_RED */
- outl(0x01, PME_IO_BASE_ADDR + 0x2c);
-
- /* GP30 - FAN2_TACH */
- outl(0x05, PME_IO_BASE_ADDR + 0x33);
-
- /* GP31 - FAN1_TACH */
- outl(0x05, PME_IO_BASE_ADDR + 0x34);
-
- /* GP32 - FAN2_CTRL */
- outl(0x04, PME_IO_BASE_ADDR + 0x35);
-
- /* GP33 - FAN1_CTRL */
- outl(0x04, PME_IO_BASE_ADDR + 0x36);
-
- /* GP34 - AUD_MUTE_OUT_R */
- outl(0x00, PME_IO_BASE_ADDR + 0x37);
-
- /* GP36 - KBRST */
- outl(0x00, PME_IO_BASE_ADDR + 0x39);
-
- /* GP37 - A20GATE */
- outl(0x00, PME_IO_BASE_ADDR + 0x3a);
-
- /* GP42 - GPIO_PME_OUT */
- outl(0x00, PME_IO_BASE_ADDR + 0x3d);
-
- /* GP50 - SER2_RI */
- outl(0x05, PME_IO_BASE_ADDR + 0x3f);
-
- /* GP51 - SER2_DCD */
- outl(0x05, PME_IO_BASE_ADDR + 0x40);
-
- /* GP52 - SER2_RX */
- outl(0x05, PME_IO_BASE_ADDR + 0x41);
-
- /* GP53 - SER2_TX */
- outl(0x04, PME_IO_BASE_ADDR + 0x42);
-
- /* GP55 - SER2_RTS */
- outl(0x04, PME_IO_BASE_ADDR + 0x44);
-
- /* GP56 - SER2_CTS */
- outl(0x05, PME_IO_BASE_ADDR + 0x45);
-
- /* GP57 - SER2_DTR */
- outl(0x04, PME_IO_BASE_ADDR + 0x46);
-
- /* GP60 - LED_GREEN */
- outl(0x01, PME_IO_BASE_ADDR + 0x47);
-
- /* GP61 - LED_YELLOW */
- outl(0x01, PME_IO_BASE_ADDR + 0x48);
-
- /* GP3 */
- outl(0xc0, PME_IO_BASE_ADDR + 0x4d);
-
- /* GP4 */
- outl(0x04, PME_IO_BASE_ADDR + 0x4e);
-
- /* FAN1 */
- outl(0x01, PME_IO_BASE_ADDR + 0x56);
-
- /* FAN2 */
- outl(0x01, PME_IO_BASE_ADDR + 0x57);
-
- /* Fan Control */
- outl(0x50, PME_IO_BASE_ADDR + 0x58);
-
- /* Fan1 Tachometer */
- outl(0xff, PME_IO_BASE_ADDR + 0x59);
-
- /* Fan2 Tachometer */
- outl(0xff, PME_IO_BASE_ADDR + 0x5a);
-
- /* LED1 */
- outl(0x00, PME_IO_BASE_ADDR + 0x5d);
-
- /* LED2 */
- outl(0x00, PME_IO_BASE_ADDR + 0x5e);
-
- /* Keyboard Scan Code */
- outl(0x00, PME_IO_BASE_ADDR + 0x5f);
-
- /* Exit the configuration state. */
- outb(0xaa, port);
-}
+/*
+ * This file is part of the coreboot project.
+ *
+ * Copyright (C) 2008 Joseph Smith <joe@settoplinux.org>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+#define PME_DEV PNP_DEV(0x2e, 0x0a)
+#define PME_IO_BASE_ADDR 0x800 /* Runtime register base address */
+#define ICH_IO_BASE_ADDR 0x00000500 /* GPIO base address register */
+
+/* Early mainboard specific GPIO setup. */
+static void mb_gpio_init(void)
+{
+ device_t dev;
+ uint16_t port;
+ uint32_t set_gpio;
+
+ /* Southbridge GPIOs. */
+ /* Set the LPC device statically. */
+ dev = PCI_DEV(0x0, 0x1f, 0x0);
+
+ /* Set the value for GPIO base address register and enable GPIO. */
+ pci_write_config32(dev, GPIO_BASE_ICH0_5, (ICH_IO_BASE_ADDR | 1));
+ pci_write_config8(dev, GPIO_CNTL_ICH0_5, 0x10);
+
+ /* Set GPIO23 to high, this enables the LAN controller. */
+ udelay(10);
+ set_gpio = inl(ICH_IO_BASE_ADDR + 0x0c);
+ set_gpio |= 1 << 23;
+ outl(set_gpio, ICH_IO_BASE_ADDR + 0x0c);
+
+ /* Super I/O GPIOs. */
+ dev = PME_DEV;
+ port = dev >> 8;
+
+ /* Enter the configuration state. */
+ outb(0x55, port);
+ pnp_set_logical_device(dev);
+ pnp_set_enable(dev, 0);
+ pnp_set_iobase(dev, PNP_IDX_IO0, PME_IO_BASE_ADDR);
+ pnp_set_enable(dev, 1);
+
+ /* GP21 - LED_RED */
+ outl(0x01, PME_IO_BASE_ADDR + 0x2c);
+
+ /* GP30 - FAN2_TACH */
+ outl(0x05, PME_IO_BASE_ADDR + 0x33);
+
+ /* GP31 - FAN1_TACH */
+ outl(0x05, PME_IO_BASE_ADDR + 0x34);
+
+ /* GP32 - FAN2_CTRL */
+ outl(0x04, PME_IO_BASE_ADDR + 0x35);
+
+ /* GP33 - FAN1_CTRL */
+ outl(0x04, PME_IO_BASE_ADDR + 0x36);
+
+ /* GP34 - AUD_MUTE_OUT_R */
+ outl(0x00, PME_IO_BASE_ADDR + 0x37);
+
+ /* GP36 - KBRST */
+ outl(0x00, PME_IO_BASE_ADDR + 0x39);
+
+ /* GP37 - A20GATE */
+ outl(0x00, PME_IO_BASE_ADDR + 0x3a);
+
+ /* GP42 - GPIO_PME_OUT */
+ outl(0x00, PME_IO_BASE_ADDR + 0x3d);
+
+ /* GP50 - SER2_RI */
+ outl(0x05, PME_IO_BASE_ADDR + 0x3f);
+
+ /* GP51 - SER2_DCD */
+ outl(0x05, PME_IO_BASE_ADDR + 0x40);
+
+ /* GP52 - SER2_RX */
+ outl(0x05, PME_IO_BASE_ADDR + 0x41);
+
+ /* GP53 - SER2_TX */
+ outl(0x04, PME_IO_BASE_ADDR + 0x42);
+
+ /* GP55 - SER2_RTS */
+ outl(0x04, PME_IO_BASE_ADDR + 0x44);
+
+ /* GP56 - SER2_CTS */
+ outl(0x05, PME_IO_BASE_ADDR + 0x45);
+
+ /* GP57 - SER2_DTR */
+ outl(0x04, PME_IO_BASE_ADDR + 0x46);
+
+ /* GP60 - LED_GREEN */
+ outl(0x01, PME_IO_BASE_ADDR + 0x47);
+
+ /* GP61 - LED_YELLOW */
+ outl(0x01, PME_IO_BASE_ADDR + 0x48);
+
+ /* GP3 */
+ outl(0xc0, PME_IO_BASE_ADDR + 0x4d);
+
+ /* GP4 */
+ outl(0x04, PME_IO_BASE_ADDR + 0x4e);
+
+ /* FAN1 */
+ outl(0x01, PME_IO_BASE_ADDR + 0x56);
+
+ /* FAN2 */
+ outl(0x01, PME_IO_BASE_ADDR + 0x57);
+
+ /* Fan Control */
+ outl(0x50, PME_IO_BASE_ADDR + 0x58);
+
+ /* Fan1 Tachometer */
+ outl(0xff, PME_IO_BASE_ADDR + 0x59);
+
+ /* Fan2 Tachometer */
+ outl(0xff, PME_IO_BASE_ADDR + 0x5a);
+
+ /* LED1 */
+ outl(0x00, PME_IO_BASE_ADDR + 0x5d);
+
+ /* LED2 */
+ outl(0x00, PME_IO_BASE_ADDR + 0x5e);
+
+ /* Keyboard Scan Code */
+ outl(0x00, PME_IO_BASE_ADDR + 0x5f);
+
+ /* Exit the configuration state. */
+ outb(0xaa, port);
+}
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-01 15:59:34 +0000