summaryrefslogtreecommitdiff
path: root/src/mainboard/supermicro
diff options
context:
space:
mode:
Diffstat (limited to 'src/mainboard/supermicro')
-rw-r--r--src/mainboard/supermicro/h8dme/Config.lb367
-rw-r--r--src/mainboard/supermicro/h8dme/Options.lb353
-rw-r--r--src/mainboard/supermicro/h8dme/apc_auto.c129
-rw-r--r--src/mainboard/supermicro/h8dme/cache_as_ram_auto.c433
-rw-r--r--src/mainboard/supermicro/h8dme/chip.h22
-rw-r--r--src/mainboard/supermicro/h8dme/cmos.layout119
-rw-r--r--src/mainboard/supermicro/h8dme/get_bus_conf.c155
-rw-r--r--src/mainboard/supermicro/h8dme/irq_tables.c119
-rw-r--r--src/mainboard/supermicro/h8dme/mainboard.c30
-rw-r--r--src/mainboard/supermicro/h8dme/mptable.c175
-rw-r--r--src/mainboard/supermicro/h8dme/resourcemap.c283
11 files changed, 2185 insertions, 0 deletions
diff --git a/src/mainboard/supermicro/h8dme/Config.lb b/src/mainboard/supermicro/h8dme/Config.lb
new file mode 100644
index 0000000000..820e0e3781
--- /dev/null
+++ b/src/mainboard/supermicro/h8dme/Config.lb
@@ -0,0 +1,367 @@
+##
+## This file is part of the coreboot project.
+##
+## This program is free software; you can redistribute it and/or modify
+## it under the terms of the GNU General Public License as published by
+## the Free Software Foundation; either version 2 of the License, or
+## (at your option) any later version.
+##
+## This program is distributed in the hope that it will be useful,
+## but WITHOUT ANY WARRANTY; without even the implied warranty of
+## MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+## GNU General Public License for more details.
+##
+## You should have received a copy of the GNU General Public License
+## along with this program; if not, write to the Free Software
+## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+##
+
+##
+## Compute the location and size of where this firmware image
+## (coreboot plus bootloader) will live in the boot rom chip.
+##
+if USE_FAILOVER_IMAGE
+ default ROM_SECTION_SIZE = FAILOVER_SIZE
+ default ROM_SECTION_OFFSET = ( ROM_SIZE - FAILOVER_SIZE )
+else
+ if USE_FALLBACK_IMAGE
+ default ROM_SECTION_SIZE = FALLBACK_SIZE
+ default ROM_SECTION_OFFSET = ( ROM_SIZE - FALLBACK_SIZE - FAILOVER_SIZE )
+ else
+ default ROM_SECTION_SIZE = ( ROM_SIZE - FALLBACK_SIZE - FAILOVER_SIZE )
+ default ROM_SECTION_OFFSET = 0
+ end
+end
+
+##
+## Compute the start location and size size of
+## The coreboot bootloader.
+##
+default PAYLOAD_SIZE = ( ROM_SECTION_SIZE - ROM_IMAGE_SIZE )
+default CONFIG_ROM_PAYLOAD_START = (0xffffffff - ROM_SIZE + ROM_SECTION_OFFSET + 1)
+
+##
+## Compute where this copy of coreboot will start in the boot rom
+##
+default _ROMBASE = ( CONFIG_ROM_PAYLOAD_START + PAYLOAD_SIZE )
+
+##
+## Compute a range of ROM that can cached to speed up coreboot,
+## execution speed.
+##
+## XIP_ROM_SIZE must be a power of 2.
+## XIP_ROM_BASE must be a multiple of XIP_ROM_SIZE
+##
+default XIP_ROM_SIZE=65536
+
+if USE_FAILOVER_IMAGE
+ default XIP_ROM_BASE = ( _ROMBASE - XIP_ROM_SIZE + ROM_IMAGE_SIZE)
+else
+ if USE_FALLBACK_IMAGE
+ default XIP_ROM_BASE = ( _ROMBASE - XIP_ROM_SIZE + ROM_IMAGE_SIZE + FAILOVER_SIZE)
+ else
+ default XIP_ROM_BASE = ( _ROMBASE - XIP_ROM_SIZE + ROM_IMAGE_SIZE)
+ end
+end
+
+arch i386 end
+
+##
+## Build the objects we have code for in this directory.
+##
+
+driver mainboard.o
+#needed by irq_tables and mptable and acpi_tables
+object get_bus_conf.o
+
+if HAVE_MP_TABLE object mptable.o end
+if HAVE_PIRQ_TABLE object irq_tables.o end
+#object reset.o
+if USE_DCACHE_RAM
+
+ if CONFIG_USE_INIT
+ makerule ./auto.o
+ depends "$(MAINBOARD)/cache_as_ram_auto.c option_table.h"
+ action "$(CC) $(DISTRO_CFLAGS) -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/cache_as_ram_auto.c -Os -nostdinc -nostdlib -fno-builtin -Wall -c -o auto.o"
+ end
+ else
+ makerule ./auto.inc
+ depends "$(MAINBOARD)/cache_as_ram_auto.c option_table.h"
+ action "$(CC) $(DISTRO_CFLAGS) -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/cache_as_ram_auto.c -Os -nostdinc -nostdlib -fno-builtin -Wall -g -dA -fverbose-asm -c -S -o $@"
+ action "perl -e 's/\.rodata/.rom.data/g' -pi $@"
+ action "perl -e 's/\.text/.section .rom.text/g' -pi $@"
+ end
+ end
+
+end
+
+if USE_FAILOVER_IMAGE
+else
+ if CONFIG_AP_CODE_IN_CAR
+ makerule ./apc_auto.o
+ depends "$(MAINBOARD)/apc_auto.c option_table.h"
+ action "$(CC) -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/apc_auto.c -Os -nostdinc -nostdlib -fno-builtin -Wall -c -o $@"
+ end
+ ldscript /arch/i386/init/ldscript_apc.lb
+ end
+end
+
+
+##
+## Build our 16 bit and 32 bit coreboot entry code
+##
+if HAVE_FAILOVER_BOOT
+ if USE_FAILOVER_IMAGE
+ mainboardinit cpu/x86/16bit/entry16.inc
+ ldscript /cpu/x86/16bit/entry16.lds
+ end
+else
+ if USE_FALLBACK_IMAGE
+ mainboardinit cpu/x86/16bit/entry16.inc
+ ldscript /cpu/x86/16bit/entry16.lds
+ end
+end
+
+mainboardinit cpu/x86/32bit/entry32.inc
+
+if USE_DCACHE_RAM
+ if CONFIG_USE_INIT
+ ldscript /cpu/x86/32bit/entry32.lds
+ end
+
+ if CONFIG_USE_INIT
+ ldscript /cpu/amd/car/cache_as_ram.lds
+ end
+end
+
+
+##
+## Build our reset vector (This is where coreboot is entered)
+##
+if HAVE_FAILOVER_BOOT
+ if USE_FAILOVER_IMAGE
+ mainboardinit cpu/x86/16bit/reset16.inc
+ ldscript /cpu/x86/16bit/reset16.lds
+ else
+ mainboardinit cpu/x86/32bit/reset32.inc
+ ldscript /cpu/x86/32bit/reset32.lds
+ end
+else
+ if USE_FALLBACK_IMAGE
+ mainboardinit cpu/x86/16bit/reset16.inc
+ ldscript /cpu/x86/16bit/reset16.lds
+ else
+ mainboardinit cpu/x86/32bit/reset32.inc
+ ldscript /cpu/x86/32bit/reset32.lds
+ end
+end
+
+##
+## Include an id string (For safe flashing)
+##
+mainboardinit southbridge/nvidia/mcp55/id.inc
+ldscript /southbridge/nvidia/mcp55/id.lds
+
+##
+## ROMSTRAP table for MCP55
+##
+if HAVE_FAILOVER_BOOT
+ if USE_FAILOVER_IMAGE
+ mainboardinit southbridge/nvidia/mcp55/romstrap.inc
+ ldscript /southbridge/nvidia/mcp55/romstrap.lds
+ end
+else
+ if USE_FALLBACK_IMAGE
+ mainboardinit southbridge/nvidia/mcp55/romstrap.inc
+ ldscript /southbridge/nvidia/mcp55/romstrap.lds
+ end
+end
+
+if USE_DCACHE_RAM
+ ##
+ ## Setup Cache-As-Ram
+ ##
+ mainboardinit cpu/amd/car/cache_as_ram.inc
+end
+
+###
+### This is the early phase of coreboot startup
+### Things are delicate and we test to see if we should
+### failover to another image.
+###
+if HAVE_FAILOVER_BOOT
+ if USE_FAILOVER_IMAGE
+ if USE_DCACHE_RAM
+ ldscript /arch/i386/lib/failover_failover.lds
+ end
+ end
+else
+ if USE_FALLBACK_IMAGE
+ if USE_DCACHE_RAM
+ ldscript /arch/i386/lib/failover.lds
+ end
+ end
+end
+
+##
+## Setup RAM
+##
+if USE_DCACHE_RAM
+
+ if CONFIG_USE_INIT
+ initobject auto.o
+ else
+ mainboardinit ./auto.inc
+ end
+end
+
+##
+## Include the secondary Configuration files
+##
+if CONFIG_CHIP_NAME
+ config chip.h
+end
+
+chip northbridge/amd/amdk8/root_complex
+ device apic_cluster 0 on
+ chip cpu/amd/socket_F
+ device apic 0 on end
+ end
+ end
+ device pci_domain 0 on
+ chip northbridge/amd/amdk8 #mc0
+ device pci 18.0 on end
+ device pci 18.0 on end
+ device pci 18.0 on
+ # devices on link 0, link 0 == LDT 0
+ chip southbridge/nvidia/mcp55
+ device pci 0.0 on end # HT
+ device pci 1.0 on # LPC
+ chip superio/winbond/w83627hf
+ device pnp 2e.0 off # Floppy
+ io 0x60 = 0x3f0
+ irq 0x70 = 6
+ drq 0x74 = 2
+ end
+ device pnp 2e.1 off # Parallel Port
+ io 0x60 = 0x378
+ irq 0x70 = 7
+ end
+ device pnp 2e.2 on # Com1
+ io 0x60 = 0x3f8
+ irq 0x70 = 4
+ end
+ device pnp 2e.3 off # Com2
+ io 0x60 = 0x2f8
+ irq 0x70 = 3
+ end
+ device pnp 2e.5 on # Keyboard
+ io 0x60 = 0x60
+ io 0x62 = 0x64
+ irq 0x70 = 1
+ irq 0x72 = 12
+ end
+ device pnp 2e.6 off # SFI
+ io 0x62 = 0x100
+ end
+ device pnp 2e.7 off # GPIO_GAME_MIDI
+ io 0x60 = 0x220
+ io 0x62 = 0x300
+ irq 0x70 = 9
+ end
+ device pnp 2e.8 off end # WDTO_PLED
+ device pnp 2e.9 off end # GPIO_SUSLED
+ device pnp 2e.a off end # ACPI
+ device pnp 2e.b on # HW Monitor
+ io 0x60 = 0x290
+ irq 0x70 = 5
+ end
+ end
+ end
+ device pci 1.1 on # SM 0
+ chip drivers/i2c/i2cmux2
+ device i2c 48 off end
+ device i2c 49 off end
+ end
+ end # SM
+ device pci 1.1 on # SM 1
+#PCI device smbus address will depend on addon pci device, do we need to scan_smbus_bus?
+# chip drivers/generic/generic #PCIXA Slot1
+# device i2c 50 on end
+# end
+# chip drivers/generic/generic #PCIXB Slot1
+# device i2c 51 on end
+# end
+# chip drivers/generic/generic #PCIXB Slot2
+# device i2c 52 on end
+# end
+# chip drivers/generic/generic #PCI Slot1
+# device i2c 53 on end
+# end
+# chip drivers/generic/generic #Master MCP55 PCI-E
+# device i2c 54 on end
+# end
+# chip drivers/generic/generic #Slave MCP55 PCI-E
+# device i2c 55 on end
+# end
+ chip drivers/generic/generic #MAC EEPROM
+ device i2c 51 on end
+ end
+
+ end # SM
+ device pci 2.0 on end # USB 1.1
+ device pci 2.1 on end # USB 2
+ device pci 4.0 on end # IDE
+ device pci 5.0 on end # SATA 0
+ device pci 5.1 on end # SATA 1
+ device pci 5.2 on end # SATA 2
+ device pci 6.0 on # PCI
+ chip drivers/pci/onboard
+ device pci 6.0 on end
+ register "rom_address" = "0xfff00000" #for 1M
+# register "rom_address" = "0xfff80000" #for 512K
+ end
+ end
+ device pci 6.1 on end # AZA
+ device pci 8.0 on end # NIC
+ device pci 9.0 on end # NIC
+ device pci a.0 on # PCI E 5
+ device pci 0.0 on #nec pci-x
+ end
+ device pci 0.1 on #nec pci-x
+ device pci 4.0 on end #scsi
+ device pci 4.1 on end #scsi
+ end
+ end
+ device pci b.0 on end # PCI E 4
+ device pci c.0 on end # PCI E 3
+ device pci d.0 on end # PCI E 2
+ device pci e.0 on end # PCI E 1
+ device pci f.0 on end # PCI E 0
+ register "ide0_enable" = "1"
+ register "sata0_enable" = "1"
+ register "sata1_enable" = "1"
+ register "mac_eeprom_smbus" = "3" # 1: smbus under 2e.8, 2: SM0 3: SM1
+ register "mac_eeprom_addr" = "0x51"
+ end
+ end # device pci 18.0
+ device pci 18.1 on end
+ device pci 18.2 on end
+ device pci 18.3 on end
+ end # mc0
+
+ end # PCI domain
+
+# chip drivers/generic/debug
+# device pnp 0.0 off end # chip name
+# device pnp 0.1 on end # pci_regs_all
+# device pnp 0.2 off end # mem
+# device pnp 0.3 off end # cpuid
+# device pnp 0.4 on end # smbus_regs_all
+# device pnp 0.5 off end # dual core msr
+# device pnp 0.6 off end # cache size
+# device pnp 0.7 off end # tsc
+# device pnp 0.8 off end # io
+# device pnp 0.9 on end # io
+# end
+end #root_complex
diff --git a/src/mainboard/supermicro/h8dme/Options.lb b/src/mainboard/supermicro/h8dme/Options.lb
new file mode 100644
index 0000000000..cec8a9651e
--- /dev/null
+++ b/src/mainboard/supermicro/h8dme/Options.lb
@@ -0,0 +1,353 @@
+##
+## This file is part of the coreboot project.
+##
+## Copyright (C) 2007 AMD
+## Written by Yinghai Lu <yinghailu@amd.com> for AMD.
+##
+## This program is free software; you can redistribute it and/or modify
+## it under the terms of the GNU General Public License as published by
+## the Free Software Foundation; either version 2 of the License, or
+## (at your option) any later version.
+##
+## This program is distributed in the hope that it will be useful,
+## but WITHOUT ANY WARRANTY; without even the implied warranty of
+## MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+## GNU General Public License for more details.
+##
+## You should have received a copy of the GNU General Public License
+## along with this program; if not, write to the Free Software
+## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+##
+
+uses HAVE_MP_TABLE
+uses HAVE_PIRQ_TABLE
+uses HAVE_ACPI_TABLES
+uses ACPI_SSDTX_NUM
+uses USE_FALLBACK_IMAGE
+uses USE_FAILOVER_IMAGE
+uses HAVE_FALLBACK_BOOT
+uses HAVE_FAILOVER_BOOT
+uses HAVE_HARD_RESET
+uses IRQ_SLOT_COUNT
+uses HAVE_OPTION_TABLE
+uses CONFIG_MAX_CPUS
+uses CONFIG_MAX_PHYSICAL_CPUS
+uses CONFIG_LOGICAL_CPUS
+uses CONFIG_IOAPIC
+uses CONFIG_SMP
+uses FALLBACK_SIZE
+uses FAILOVER_SIZE
+uses ROM_SIZE
+uses ROM_SECTION_SIZE
+uses ROM_IMAGE_SIZE
+uses ROM_SECTION_SIZE
+uses ROM_SECTION_OFFSET
+uses CONFIG_ROM_PAYLOAD
+uses CONFIG_ROM_PAYLOAD_START
+uses CONFIG_COMPRESSED_PAYLOAD_NRV2B
+uses CONFIG_COMPRESSED_PAYLOAD_LZMA
+uses CONFIG_PRECOMPRESSED_PAYLOAD
+uses PAYLOAD_SIZE
+uses _ROMBASE
+uses XIP_ROM_SIZE
+uses XIP_ROM_BASE
+uses STACK_SIZE
+uses HEAP_SIZE
+uses USE_OPTION_TABLE
+uses LB_CKS_RANGE_START
+uses LB_CKS_RANGE_END
+uses LB_CKS_LOC
+uses MAINBOARD_PART_NUMBER
+uses MAINBOARD_VENDOR
+uses MAINBOARD
+uses MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID
+uses MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID
+uses COREBOOT_EXTRA_VERSION
+uses _RAMBASE
+uses TTYS0_BAUD
+uses TTYS0_BASE
+uses TTYS0_LCS
+uses DEFAULT_CONSOLE_LOGLEVEL
+uses MAXIMUM_CONSOLE_LOGLEVEL
+uses MAINBOARD_POWER_ON_AFTER_POWER_FAIL
+uses CONFIG_CONSOLE_SERIAL8250
+uses HAVE_INIT_TIMER
+uses CONFIG_GDB_STUB
+uses CONFIG_GDB_STUB
+uses CROSS_COMPILE
+uses CC
+uses HOSTCC
+uses OBJCOPY
+uses CONFIG_CHIP_NAME
+uses CONFIG_CONSOLE_VGA
+uses CONFIG_PCI_ROM_RUN
+uses HW_MEM_HOLE_SIZEK
+uses HW_MEM_HOLE_SIZE_AUTO_INC
+uses K8_HT_FREQ_1G_SUPPORT
+
+uses HT_CHAIN_UNITID_BASE
+uses HT_CHAIN_END_UNITID_BASE
+uses SB_HT_CHAIN_ON_BUS0
+uses SB_HT_CHAIN_UNITID_OFFSET_ONLY
+
+uses USE_DCACHE_RAM
+uses DCACHE_RAM_BASE
+uses DCACHE_RAM_SIZE
+uses DCACHE_RAM_GLOBAL_VAR_SIZE
+uses CONFIG_USE_INIT
+
+uses SERIAL_CPU_INIT
+
+uses ENABLE_APIC_EXT_ID
+uses APIC_ID_OFFSET
+uses LIFT_BSP_APIC_ID
+
+uses CONFIG_PCI_64BIT_PREF_MEM
+
+uses CONFIG_LB_MEM_TOPK
+
+uses CONFIG_AP_CODE_IN_CAR
+
+uses MEM_TRAIN_SEQ
+
+uses WAIT_BEFORE_CPUS_INIT
+
+uses CONFIG_USE_PRINTK_IN_CAR
+
+###
+### Build options
+###
+
+##
+## ROM_SIZE is the size of boot ROM that this board will use.
+##
+#default ROM_SIZE=524288
+default ROM_SIZE=0x100000
+
+##
+## FALLBACK_SIZE is the amount of the ROM the complete fallback image will use
+##
+#default FALLBACK_SIZE=131072
+#default FALLBACK_SIZE=0x40000
+
+#FALLBACK: 256K-4K
+default FALLBACK_SIZE=0x3f000
+#FAILOVER: 4K
+default FAILOVER_SIZE=0x01000
+
+#more 1M for pgtbl
+default CONFIG_LB_MEM_TOPK=2048
+
+##
+## Build code for the fallback boot
+##
+default HAVE_FALLBACK_BOOT=1
+default HAVE_FAILOVER_BOOT=1
+
+##
+## Build code to reset the motherboard from coreboot
+##
+default HAVE_HARD_RESET=1
+
+##
+## Build code to export a programmable irq routing table
+##
+default HAVE_PIRQ_TABLE=1
+default IRQ_SLOT_COUNT=11
+
+##
+## Build code to export an x86 MP table
+## Useful for specifying IRQ routing values
+##
+default HAVE_MP_TABLE=1
+
+## ACPI tables will be included
+default HAVE_ACPI_TABLES=0
+
+##
+## Build code to export a CMOS option table
+##
+default HAVE_OPTION_TABLE=1
+
+##
+## Move the default coreboot cmos range off of AMD RTC registers
+##
+default LB_CKS_RANGE_START=49
+default LB_CKS_RANGE_END=122
+default LB_CKS_LOC=123
+
+##
+## Build code for SMP support
+## Only worry about 2 micro processors
+##
+default CONFIG_SMP=1
+default CONFIG_MAX_CPUS=4
+default CONFIG_MAX_PHYSICAL_CPUS=2
+default CONFIG_LOGICAL_CPUS=1
+
+default SERIAL_CPU_INIT=0
+
+default ENABLE_APIC_EXT_ID=0
+default APIC_ID_OFFSET=0x10
+default LIFT_BSP_APIC_ID=1
+
+#CHIP_NAME ?
+default CONFIG_CHIP_NAME=1
+
+#memory hole size, 0 mean disable, others will enable the hole, at that case if it is small than mmio_basek, it will use mmio_basek instead.
+#2G
+#default HW_MEM_HOLE_SIZEK=0x200000
+#1G
+default HW_MEM_HOLE_SIZEK=0x100000
+#512M
+#default HW_MEM_HOLE_SIZEK=0x80000
+
+#make auto increase hole size to avoid hole_startk equal to basek so as to make some kernel happy
+#default HW_MEM_HOLE_SIZE_AUTO_INC=1
+
+#Opteron K8 1G HT Support
+default K8_HT_FREQ_1G_SUPPORT=1
+
+#VGA Console
+default CONFIG_CONSOLE_VGA=1
+default CONFIG_PCI_ROM_RUN=1
+
+#HT Unit ID offset, default is 1, the typical one, 0 mean only one HT device
+default HT_CHAIN_UNITID_BASE=0
+
+#real SB Unit ID, default is 0x20, mean dont touch it at last
+#default HT_CHAIN_END_UNITID_BASE=0x6
+
+#make the SB HT chain on bus 0, default is not (0)
+default SB_HT_CHAIN_ON_BUS0=2
+
+#only offset for SB chain?, default is yes(1)
+default SB_HT_CHAIN_UNITID_OFFSET_ONLY=0
+
+#allow capable device use that above 4G
+#default CONFIG_PCI_64BIT_PREF_MEM=1
+
+##
+## enable CACHE_AS_RAM specifics
+##
+default USE_DCACHE_RAM=1
+default DCACHE_RAM_BASE=0xc8000
+default DCACHE_RAM_SIZE=0x08000
+default DCACHE_RAM_GLOBAL_VAR_SIZE=0x01000
+default CONFIG_USE_INIT=0
+
+default CONFIG_AP_CODE_IN_CAR=1
+default MEM_TRAIN_SEQ=1
+default WAIT_BEFORE_CPUS_INIT=1
+
+##
+## Build code to setup a generic IOAPIC
+##
+default CONFIG_IOAPIC=1
+
+##
+## Clean up the motherboard id strings
+##
+default MAINBOARD_PART_NUMBER="h8dmr"
+default MAINBOARD_VENDOR="Supermicro"
+default MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x15d9
+default MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x1511
+
+###
+### coreboot layout values
+###
+
+## ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy.
+default ROM_IMAGE_SIZE = 65536
+
+##
+## Use a small 8K stack
+##
+default STACK_SIZE=0x2000
+
+##
+## Use a small 32K heap
+##
+default HEAP_SIZE=0x8000
+
+##
+## Only use the option table in a normal image
+##
+default USE_OPTION_TABLE = (!USE_FALLBACK_IMAGE) && (!USE_FAILOVER_IMAGE )
+
+##
+## Coreboot C code runs at this location in RAM
+##
+default _RAMBASE=0x00100000
+
+##
+## Load the payload from the ROM
+##
+default CONFIG_ROM_PAYLOAD = 1
+
+#default CONFIG_COMPRESSED_PAYLOAD = 1
+
+###
+### Defaults of options that you may want to override in the target config file
+###
+
+##
+## The default compiler
+##
+default CC="$(CROSS_COMPILE)gcc -m32"
+default HOSTCC="gcc"
+
+##
+## Disable the gdb stub by default
+##
+default CONFIG_GDB_STUB=0
+
+##
+## The Serial Console
+##
+default CONFIG_USE_PRINTK_IN_CAR=1
+
+# To Enable the Serial Console
+default CONFIG_CONSOLE_SERIAL8250=1
+
+## Select the serial console baud rate
+default TTYS0_BAUD=115200
+#default TTYS0_BAUD=57600
+#default TTYS0_BAUD=38400
+#default TTYS0_BAUD=19200
+#default TTYS0_BAUD=9600
+#default TTYS0_BAUD=4800
+#default TTYS0_BAUD=2400
+#default TTYS0_BAUD=1200
+
+# Select the serial console base port
+default TTYS0_BASE=0x3f8
+
+# Select the serial protocol
+# This defaults to 8 data bits, 1 stop bit, and no parity
+default TTYS0_LCS=0x3
+
+##
+### Select the coreboot loglevel
+##
+## EMERG 1 system is unusable
+## ALERT 2 action must be taken immediately
+## CRIT 3 critical conditions
+## ERR 4 error conditions
+## WARNING 5 warning conditions
+## NOTICE 6 normal but significant condition
+## INFO 7 informational
+## DEBUG 8 debug-level messages
+## SPEW 9 Way too many details
+
+## Request this level of debugging output
+default DEFAULT_CONSOLE_LOGLEVEL=9
+## At a maximum only compile in this level of debugging
+default MAXIMUM_CONSOLE_LOGLEVEL=9
+
+##
+## Select power on after power fail setting
+default MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON"
+
+### End Options.lb
+end
diff --git a/src/mainboard/supermicro/h8dme/apc_auto.c b/src/mainboard/supermicro/h8dme/apc_auto.c
new file mode 100644
index 0000000000..b514715e3f
--- /dev/null
+++ b/src/mainboard/supermicro/h8dme/apc_auto.c
@@ -0,0 +1,129 @@
+/*
+ * This file is part of the coreboot project.
+ *
+ * Copyright (C) 2007 AMD
+ * Written by Yinghai Lu <yinghailu@amd.com> for AMD.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+#define ASSEMBLY 1
+#define __ROMCC__
+
+#define RAMINIT_SYSINFO 1
+#define CACHE_AS_RAM_ADDRESS_DEBUG 0
+
+#define SET_NB_CFG_54 1
+
+//used by raminit
+#define QRANK_DIMM_SUPPORT 1
+
+#define K8_REV_F_SUPPORT_F0_F1_WORKAROUND 0
+
+#include <stdint.h>
+#include <device/pci_def.h>
+#include <device/pci_ids.h>
+#include <arch/io.h>
+#include <device/pnp_def.h>
+#include <arch/romcc_io.h>
+#include <cpu/x86/lapic.h>
+#include "option_table.h"
+#include "pc80/mc146818rtc_early.c"
+#include "pc80/serial.c"
+
+#if CONFIG_USE_INIT == 0
+ #include "lib/memcpy.c"
+#endif
+
+#include "arch/i386/lib/console.c"
+
+#if 0
+static void post_code(uint8_t value) {
+#if 1
+ int i;
+ for(i=0;i<0x80000;i++) {
+ outb(value, 0x80);
+ }
+#endif
+}
+#endif
+
+#include <cpu/amd/model_fxx_rev.h>
+#include "northbridge/amd/amdk8/raminit.h"
+#include "cpu/amd/model_fxx/apic_timer.c"
+
+#include "lib/delay.c"
+
+//#include "cpu/x86/lapic/boot_cpu.c"
+#include "northbridge/amd/amdk8/reset_test.c"
+
+#include "northbridge/amd/amdk8/debug.c"
+
+#include "southbridge/nvidia/mcp55/mcp55_early_ctrl.c"
+
+#include "northbridge/amd/amdk8/amdk8_f.h"
+
+#include "cpu/x86/mtrr.h"
+#include "cpu/amd/mtrr.h"
+#include "cpu/x86/tsc.h"
+
+#include "northbridge/amd/amdk8/amdk8_f_pci.c"
+#include "northbridge/amd/amdk8/raminit_f_dqs.c"
+
+#include "cpu/amd/dualcore/dualcore.c"
+
+void hardwaremain(int ret_addr)
+{
+ struct sys_info *sysinfo = (DCACHE_RAM_BASE + DCACHE_RAM_SIZE - DCACHE_RAM_GLOBAL_VAR_SIZE); // in CACHE
+ struct sys_info *sysinfox = ((CONFIG_LB_MEM_TOPK<<10) - DCACHE_RAM_GLOBAL_VAR_SIZE); // in RAM
+
+ struct node_core_id id;
+
+ id = get_node_core_id_x();
+
+ print_debug("CODE IN CACHE ON NODE:"); print_debug_hex8(id.nodeid); print_debug("\r\n");
+
+ train_ram(id.nodeid, sysinfo, sysinfox);
+
+ /*
+ go back, but can not use stack any more, because we only keep ret_addr and can not restore esp, and ebp
+ */
+
+ __asm__ volatile (
+ "movl %0, %%edi\n\t"
+ "jmp *%%edi\n\t"
+ :: "a"(ret_addr)
+ );
+
+
+
+}
+struct eregs {
+ uint32_t eax, ecx, edx, ebx, esp, ebp, esi, edi;
+ uint32_t vector;
+ uint32_t error_code;
+ uint32_t eip;
+ uint32_t cs;
+ uint32_t eflags;
+};
+
+void x86_exception(struct eregs *info)
+{
+ do {
+ hlt();
+ } while(1);
+}
+
+
diff --git a/src/mainboard/supermicro/h8dme/cache_as_ram_auto.c b/src/mainboard/supermicro/h8dme/cache_as_ram_auto.c
new file mode 100644
index 0000000000..ed6be2c010
--- /dev/null
+++ b/src/mainboard/supermicro/h8dme/cache_as_ram_auto.c
@@ -0,0 +1,433 @@
+/*
+ * This file is part of the coreboot project.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+#define ASSEMBLY 1
+#define __ROMCC__
+
+#define RAMINIT_SYSINFO 1
+
+#define K8_ALLOCATE_IO_RANGE 1
+// #define K8_SCAN_PCI_BUS 1
+
+#define QRANK_DIMM_SUPPORT 1
+
+#if CONFIG_LOGICAL_CPUS==1
+#define SET_NB_CFG_54 1
+#endif
+
+// used by init_cpus and fidvid
+#define K8_SET_FIDVID 1
+//if we want to wait for core1 done before DQS training, set it to 0
+#define K8_SET_FIDVID_CORE0_ONLY 1
+
+#if K8_REV_F_SUPPORT == 1
+#define K8_REV_F_SUPPORT_F0_F1_WORKAROUND 0
+#endif
+
+#include <stdint.h>
+#include <device/pci_def.h>
+#include <device/pci_ids.h>
+#include <arch/io.h>
+#include <device/pnp_def.h>
+#include <arch/romcc_io.h>
+#include <cpu/x86/lapic.h>
+#include "option_table.h"
+#include "pc80/mc146818rtc_early.c"
+
+// for enable the FAN
+#include "southbridge/nvidia/mcp55/mcp55_early_smbus.c"
+
+#if USE_FAILOVER_IMAGE==0
+#include "pc80/serial.c"
+#include "arch/i386/lib/console.c"
+#include "ram/ramtest.c"
+
+#include <cpu/amd/model_fxx_rev.h>
+
+// #include "southbridge/nvidia/mcp55/mcp55_early_smbus.c"
+#include "northbridge/amd/amdk8/raminit.h"
+#include "cpu/amd/model_fxx/apic_timer.c"
+#include "lib/delay.c"
+
+#endif
+
+#include "cpu/x86/lapic/boot_cpu.c"
+#include "northbridge/amd/amdk8/reset_test.c"
+#include "superio/winbond/w83627hf/w83627hf_early_serial.c"
+#include "superio/winbond/w83627hf/w83627hf_early_init.c"
+
+#if USE_FAILOVER_IMAGE==0
+
+#include "cpu/x86/bist.h"
+
+#if CONFIG_USE_INIT == 0
+#include "lib/memcpy.c"
+#endif
+
+#include "northbridge/amd/amdk8/debug.c"
+
+#include "cpu/amd/mtrr/amd_earlymtrr.c"
+
+#include "northbridge/amd/amdk8/setup_resource_map.c"
+
+#define SERIAL_DEV PNP_DEV(0x2e, W83627HF_SP1)
+
+#include "southbridge/nvidia/mcp55/mcp55_early_ctrl.c"
+
+static void memreset_setup(void)
+{
+}
+
+static void memreset(int controllers, const struct mem_controller *ctrl)
+{
+}
+
+static int smbus_send_byte_one(unsigned device, unsigned char val)
+{
+ return do_smbus_send_byte(SMBUS1_IO_BASE, device, val);
+}
+
+static void dump_smbus_registers(void)
+{
+ u32 device;
+
+ print_debug("\r\n");
+ for (device = 1; device < 0x80; device++) {
+ int j;
+ if (smbus_read_byte(device, 0) < 0)
+ continue;
+ printk_debug("smbus: %02x", device);
+ for (j = 0; j < 256; j++) {
+ int status;
+ unsigned char byte;
+ status = smbus_read_byte(device, j);
+ if (status < 0) {
+ break;
+ }
+ if ((j & 0xf) == 0) {
+ printk_debug("\r\n%02x: ", j);
+ }
+ byte = status & 0xff;
+ printk_debug("%02x ", byte);
+ }
+ print_debug("\r\n");
+ }
+}
+
+static inline void activate_spd_rom(const struct mem_controller *ctrl)
+{
+/* We don't do any switching yet.
+#define SMBUS_SWITCH1 0x48
+#define SMBUS_SWITCH2 0x49
+ unsigned device=(ctrl->channel0[0])>>8;
+ smbus_send_byte(SMBUS_SWITCH1, device);
+ smbus_send_byte(SMBUS_SWITCH2, (device >> 4) & 0x0f);
+*/
+ /* nothing to do */
+}
+
+/*
+static inline void change_i2c_mux(unsigned device)
+{
+#define SMBUS_SWITCH1 0x48
+#define SMBUS_SWITHC2 0x49
+ smbus_send_byte(SMBUS_SWITCH1, device & 0x0f);
+ smbus_send_byte_one(SMBUS_SWITCH2, (device >> 4) & 0x0f);
+ int ret;
+ print_debug("change_i2c_mux i="); print_debug_hex8(device); print_debug("\r\n");
+ dump_smbus_registers();
+ ret = smbus_send_byte(SMBUS_SWITCH1, device);
+ print_debug("change_i2c_mux ret="); print_debug_hex32(ret); print_debug("\r\n");
+ dump_smbus_registers();
+ ret = smbus_send_byte_one(SMBUS_SWITCH2, device);
+ print_debug("change_i2c_mux ret="); print_debug_hex32(ret); print_debug("\r\n");
+ dump_smbus_registers();
+}
+*/
+
+static inline int spd_read_byte(unsigned device, unsigned address)
+{
+ return smbus_read_byte(device, address);
+}
+
+#include "northbridge/amd/amdk8/amdk8_f.h"
+#include "northbridge/amd/amdk8/coherent_ht.c"
+
+#include "northbridge/amd/amdk8/incoherent_ht.c"
+
+#include "northbridge/amd/amdk8/raminit_f.c"
+
+#include "sdram/generic_sdram.c"
+
+#include "resourcemap.c"
+
+#include "cpu/amd/dualcore/dualcore.c"
+
+#define MCP55_NUM 1
+#define MCP55_USE_NIC 1
+#define MCP55_USE_AZA 1
+
+#define MCP55_PCI_E_X_0 4
+
+#include "southbridge/nvidia/mcp55/mcp55_early_setup_ss.h"
+#include "southbridge/nvidia/mcp55/mcp55_early_setup_car.c"
+
+#include "cpu/amd/car/copy_and_run.c"
+
+#include "cpu/amd/car/post_cache_as_ram.c"
+
+#include "cpu/amd/model_fxx/init_cpus.c"
+
+#include "cpu/amd/model_fxx/fidvid.c"
+
+#endif
+
+#if ((HAVE_FAILOVER_BOOT==1) && (USE_FAILOVER_IMAGE == 1)) || ((HAVE_FAILOVER_BOOT==0) && (USE_FALLBACK_IMAGE == 1))
+
+#include "southbridge/nvidia/mcp55/mcp55_enable_rom.c"
+#include "northbridge/amd/amdk8/early_ht.c"
+
+static void sio_setup(void)
+{
+
+ u32 value;
+ uint32_t dword;
+ uint8_t byte;
+
+ enable_smbus();
+// smbusx_write_byte(1, (0x58>>1), 0, 0x80); /* select bank0 */
+ smbusx_write_byte(1, (0x58 >> 1), 0xb1, 0xff); /* set FAN ctrl to DC mode */
+
+ byte = pci_read_config8(PCI_DEV(0, MCP55_DEVN_BASE + 1, 0), 0x7b);
+ byte |= 0x20;
+ pci_write_config8(PCI_DEV(0, MCP55_DEVN_BASE + 1, 0), 0x7b, byte);
+
+ dword = pci_read_config32(PCI_DEV(0, MCP55_DEVN_BASE + 1, 0), 0xa0);
+ dword |= (1 << 0);
+ pci_write_config32(PCI_DEV(0, MCP55_DEVN_BASE + 1, 0), 0xa0, dword);
+
+ dword = pci_read_config32(PCI_DEV(0, MCP55_DEVN_BASE + 1, 0), 0xa4);
+ dword |= (1 << 16);
+ pci_write_config32(PCI_DEV(0, MCP55_DEVN_BASE + 1, 0), 0xa4, dword);
+
+}
+
+void failover_process(unsigned long bist, unsigned long cpu_init_detectedx)
+{
+ u32 last_boot_normal_x = last_boot_normal();
+
+ /* Is this a cpu only reset? or Is this a secondary cpu? */
+ if ((cpu_init_detectedx) || (!boot_cpu())) {
+ if (last_boot_normal_x) {
+ goto normal_image;
+ } else {
+ goto fallback_image;
+ }
+ }
+
+ /* Nothing special needs to be done to find bus 0 */
+ /* Allow the HT devices to be found */
+
+ enumerate_ht_chain();
+
+ sio_setup();
+
+ /* Setup the mcp55 */
+ mcp55_enable_rom();
+
+ /* Is this a deliberate reset by the bios */
+ if (bios_reset_detected() && last_boot_normal_x) {
+ goto normal_image;
+ }
+ /* This is the primary cpu how should I boot? */
+ else if (do_normal_boot()) {
+ goto normal_image;
+ } else {
+ goto fallback_image;
+ }
+normal_image:
+ __asm__ volatile ("jmp __normal_image": /* outputs */
+ :"a" (bist), "b"(cpu_init_detectedx) /* inputs */
+ );
+
+ fallback_image:
+#if HAVE_FAILOVER_BOOT==1
+ __asm__ volatile ("jmp __fallback_image": /* outputs */
+ :"a" (bist), "b"(cpu_init_detectedx) /* inputs */
+ )
+#endif
+ ;
+}
+#endif
+void real_main(unsigned long bist, unsigned long cpu_init_detectedx);
+
+void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
+{
+#if HAVE_FAILOVER_BOOT==1
+#if USE_FAILOVER_IMAGE==1
+ failover_process(bist, cpu_init_detectedx);
+#else
+ real_main(bist, cpu_init_detectedx);
+#endif
+#else
+#if USE_FALLBACK_IMAGE == 1
+ failover_process(bist, cpu_init_detectedx);
+#endif
+ real_main(bist, cpu_init_detectedx);
+#endif
+}
+
+/* We have no idea where the SMBUS switch is. This doesn't do anything ATM. */
+#define RC0 (2<<8)
+#define RC1 (1<<8)
+
+#if USE_FAILOVER_IMAGE==0
+
+void real_main(unsigned long bist, unsigned long cpu_init_detectedx)
+{
+/* The SPD is being read from the CPU1 (marked CPU2 on the board) and we
+ don't know how to switch the SMBus to decode the CPU0 SPDs. So, The
+ memory on each CPU must be an exact match.
+ */
+ static const uint16_t spd_addr[] = {
+ RC0 | (0xa << 3) | 0, RC0 | (0xa << 3) | 2,
+ RC0 | (0xa << 3) | 4, RC0 | (0xa << 3) | 6,
+ RC0 | (0xa << 3) | 1, RC0 | (0xa << 3) | 3,
+ RC0 | (0xa << 3) | 5, RC0 | (0xa << 3) | 7,
+#if CONFIG_MAX_PHYSICAL_CPUS > 1
+ RC1 | (0xa << 3) | 0, RC1 | (0xa << 3) | 2,
+ RC1 | (0xa << 3) | 4, RC1 | (0xa << 3) | 6,
+ RC1 | (0xa << 3) | 1, RC1 | (0xa << 3) | 3,
+ RC1 | (0xa << 3) | 5, RC1 | (0xa << 3) | 7,
+#endif
+ };
+
+ struct sys_info *sysinfo =
+ (DCACHE_RAM_BASE + DCACHE_RAM_SIZE - DCACHE_RAM_GLOBAL_VAR_SIZE);
+
+ int needs_reset = 0;
+ unsigned bsp_apicid = 0;
+
+ if (bist == 0) {
+ bsp_apicid = init_cpus(cpu_init_detectedx, sysinfo);
+ }
+
+ pnp_enter_ext_func_mode(SERIAL_DEV);
+ pnp_write_config(SERIAL_DEV, 0x24, 0x84 | (1 << 6));
+ w83627hf_enable_dev(SERIAL_DEV, TTYS0_BASE);
+ pnp_exit_ext_func_mode(SERIAL_DEV);
+
+ uart_init();
+ console_init();
+
+ /* Halt if there was a built in self test failure */
+ report_bist_failure(bist);
+
+ print_debug("*sysinfo range: [");
+ print_debug_hex32(sysinfo);
+ print_debug(",");
+ print_debug_hex32((unsigned long)sysinfo + sizeof(struct sys_info));
+ print_debug(")\r\n");
+
+ setup_mb_resource_map();
+
+ print_debug("bsp_apicid=");
+ print_debug_hex8(bsp_apicid);
+ print_debug("\r\n");
+
+#if MEM_TRAIN_SEQ == 1
+ set_sysinfo_in_ram(0); // in BSP so could hold all ap until sysinfo is in ram
+#endif
+/* dump_smbus_registers(); */
+ setup_coherent_ht_domain(); // routing table and start other core0
+
+ wait_all_core0_started();
+#if CONFIG_LOGICAL_CPUS==1
+ // It is said that we should start core1 after all core0 launched
+ /* becase optimize_link_coherent_ht is moved out from setup_coherent_ht_domain,
+ * So here need to make sure last core0 is started, esp for two way system,
+ * (there may be apic id conflicts in that case)
+ */
+ start_other_cores();
+ wait_all_other_cores_started(bsp_apicid);
+#endif
+
+ /* it will set up chains and store link pair for optimization later */
+ ht_setup_chains_x(sysinfo); // it will init sblnk and sbbusn, nodes, sbdn
+
+#if K8_SET_FIDVID == 1
+
+ {
+ msr_t msr;
+ msr = rdmsr(0xc0010042);
+ print_debug("begin msr fid, vid ");
+ print_debug_hex32(msr.hi);
+ print_debug_hex32(msr.lo);
+ print_debug("\r\n");
+
+ }
+
+ enable_fid_change();
+
+ enable_fid_change_on_sb(sysinfo->sbbusn, sysinfo->sbdn);
+
+ init_fidvid_bsp(bsp_apicid);
+
+ // show final fid and vid
+ {
+ msr_t msr;
+ msr = rdmsr(0xc0010042);
+ print_debug("end msr fid, vid ");
+ print_debug_hex32(msr.hi);
+ print_debug_hex32(msr.lo);
+ print_debug("\r\n");
+
+ }
+#endif
+
+#if 1
+ needs_reset |= optimize_link_coherent_ht();
+ needs_reset |= optimize_link_incoherent_ht(sysinfo);
+ needs_reset |= mcp55_early_setup_x();
+
+ // fidvid change will issue one LDTSTOP and the HT change will be effective too
+ if (needs_reset) {
+ print_info("ht reset -\r\n");
+ soft_reset();
+ }
+#endif
+ allow_all_aps_stop(bsp_apicid);
+
+ //It's the time to set ctrl in sysinfo now;
+ fill_mem_ctrl(sysinfo->nodes, sysinfo->ctrl, spd_addr);
+
+ enable_smbus(); /* enable in sio_setup */
+
+ memreset_setup();
+
+ //do we need apci timer, tsc...., only debug need it for better output
+ /* all ap stopped? */
+// init_timer(); // Need to use TMICT to synconize FID/VID
+
+ sdram_initialize(sysinfo->nodes, sysinfo->ctrl, sysinfo);
+
+ post_cache_as_ram(); // bsp swtich stack to ram and copy sysinfo ram now
+
+}
+
+#endif
diff --git a/src/mainboard/supermicro/h8dme/chip.h b/src/mainboard/supermicro/h8dme/chip.h
new file mode 100644
index 0000000000..6d7212fd2b
--- /dev/null
+++ b/src/mainboard/supermicro/h8dme/chip.h
@@ -0,0 +1,22 @@
+/*
+ * This file is part of the coreboot project.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+extern struct chip_operations mainboard_ops;
+
+struct mainboard_config {
+};
diff --git a/src/mainboard/supermicro/h8dme/cmos.layout b/src/mainboard/supermicro/h8dme/cmos.layout
new file mode 100644
index 0000000000..0621cfc2fd
--- /dev/null
+++ b/src/mainboard/supermicro/h8dme/cmos.layout
@@ -0,0 +1,119 @@
+##
+## This file is part of the coreboot project.
+##
+## Copyright (C) 2007 AMD
+## Written by Yinghai Lu <yinghailu@amd.com> for AMD.
+##
+## This program is free software; you can redistribute it and/or modify
+## it under the terms of the GNU General Public License as published by
+## the Free Software Foundation; either version 2 of the License, or
+## (at your option) any later version.
+##
+## This program is distributed in the hope that it will be useful,
+## but WITHOUT ANY WARRANTY; without even the implied warranty of
+## MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+## GNU General Public License for more details.
+##
+## You should have received a copy of the GNU General Public License
+## along with this program; if not, write to the Free Software
+## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+##
+
+entries
+
+#start-bit length config config-ID name
+#0 8 r 0 seconds
+#8 8 r 0 alarm_seconds
+#16 8 r 0 minutes
+#24 8 r 0 alarm_minutes
+#32 8 r 0 hours
+#40 8 r 0 alarm_hours
+#48 8 r 0 day_of_week
+#56 8 r 0 day_of_month
+#64 8 r 0 month
+#72 8 r 0 year
+#80 4 r 0 rate_select
+#84 3 r 0 REF_Clock
+#87 1 r 0 UIP
+#88 1 r 0 auto_switch_DST
+#89 1 r 0 24_hour_mode
+#90 1 r 0 binary_values_enable
+#91 1 r 0 square-wave_out_enable
+#92 1 r 0 update_finished_enable
+#93 1 r 0 alarm_interrupt_enable
+#94 1 r 0 periodic_interrupt_enable
+#95 1 r 0 disable_clock_updates
+#96 288 r 0 temporary_filler
+0 384 r 0 reserved_memory
+384 1 e 4 boot_option
+385 1 e 4 last_boot
+386 1 e 1 ECC_memory
+388 4 r 0 reboot_bits
+392 3 e 5 baud_rate
+395 1 e 1 hw_scrubber
+396 1 e 1 interleave_chip_selects
+397 2 e 8 max_mem_clock
+399 1 e 2 dual_core
+400 1 e 1 power_on_after_fail
+412 4 e 6 debug_level
+416 4 e 7 boot_first
+420 4 e 7 boot_second
+424 4 e 7 boot_third
+428 4 h 0 boot_index
+432 8 h 0 boot_countdown
+440 4 e 9 slow_cpu
+444 1 e 1 nmi
+445 1 e 1 iommu
+728 256 h 0 user_data
+984 16 h 0 check_sum
+# Reserve the extended AMD configuration registers
+1000 24 r 0 reserved_memory
+
+
+
+enumerations
+
+#ID value text
+1 0 Disable
+1 1 Enable
+2 0 Enable
+2 1 Disable
+4 0 Fallback
+4 1 Normal
+5 0 115200
+5 1 57600
+5 2 38400
+5 3 19200
+5 4 9600
+5 5 4800
+5 6 2400
+5 7 1200
+6 6 Notice
+6 7 Info
+6 8 Debug
+6 9 Spew
+7 0 Network
+7 1 HDD
+7 2 Floppy
+7 8 Fallback_Network
+7 9 Fallback_HDD
+7 10 Fallback_Floppy
+#7 3 ROM
+8 0 200Mhz
+8 1 166Mhz
+8 2 133Mhz
+8 3 100Mhz
+9 0 off
+9 1 87.5%
+9 2 75.0%
+9 3 62.5%
+9 4 50.0%
+9 5 37.5%
+9 6 25.0%
+9 7 12.5%
+
+checksums
+
+checksum 392 983 984
+
+
diff --git a/src/mainboard/supermicro/h8dme/get_bus_conf.c b/src/mainboard/supermicro/h8dme/get_bus_conf.c
new file mode 100644
index 0000000000..3402d9d5f6
--- /dev/null
+++ b/src/mainboard/supermicro/h8dme/get_bus_conf.c
@@ -0,0 +1,155 @@
+/*
+ * This file is part of the coreboot project.
+ *
+ * Copyright (C) 2007 AMD
+ * Written by Yinghai Lu <yinghailu@amd.com> for AMD.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+#include <console/console.h>
+#include <device/pci.h>
+#include <device/pci_ids.h>
+#include <string.h>
+#include <stdint.h>
+#if CONFIG_LOGICAL_CPUS==1
+#include <cpu/amd/dualcore.h>
+#endif
+
+#include <cpu/amd/amdk8_sysconf.h>
+#include <stdlib.h>
+
+
+// Global variables for MB layouts and these will be shared by irqtable mptable and acpi_tables
+//busnum is default
+ unsigned char bus_isa;
+ unsigned char bus_mcp55[8]; //1
+ unsigned apicid_mcp55;
+
+ unsigned char bus_pcix[3]; // under bus_mcp55_2
+
+unsigned pci1234x[] =
+{ //Here you only need to set value in pci1234 for HT-IO that could be installed or not
+ //You may need to preset pci1234 for HTIO board, please refer to src/northbridge/amd/amdk8/get_sblk_pci1234.c for detail
+ 0x0000ff0,
+ 0x0000ff0,
+// 0x0000ff0,
+// 0x0000ff0,
+// 0x0000ff0,
+// 0x0000ff0,
+// 0x0000ff0,
+// 0x0000ff0
+};
+unsigned hcdnx[] =
+{ //HT Chain device num, actually it is unit id base of every ht device in chain, assume every chain only have 4 ht device at most
+ 0x20202020,
+ 0x20202020,
+// 0x20202020,
+// 0x20202020,
+// 0x20202020,
+// 0x20202020,
+// 0x20202020,
+// 0x20202020,
+};
+unsigned sbdnb;
+
+extern void get_sblk_pci1234(void);
+
+static unsigned get_bus_conf_done = 0;
+
+void get_bus_conf(void)
+{
+
+ unsigned apicid_base;
+ unsigned sbdn;
+
+ device_t dev;
+ int i;
+
+ if(get_bus_conf_done==1) return; //do it only once
+
+ get_bus_conf_done = 1;
+
+ sysconf.hc_possible_num = ARRAY_SIZE(pci1234x);
+ for(i=0;i<sysconf.hc_possible_num; i++) {
+ sysconf.pci1234[i] = pci1234x[i];
+ sysconf.hcdn[i] = hcdnx[i];
+ }
+
+ get_sblk_pci1234();
+
+ sysconf.sbdn = (sysconf.hcdn[0] & 0xff); // first byte of first chain
+ sbdn = sysconf.sbdn;
+
+ sbdnb = (sysconf.hcdn[1] & 0xff); // first byte of second chain
+
+ for(i=0; i<8; i++) {
+ bus_mcp55[i] = 0;
+ }
+
+ for(i=0; i<3; i++) {
+ bus_pcix[i] = 0;
+ }
+
+
+ bus_mcp55[0] = (sysconf.pci1234[0] >> 16) & 0xff;
+
+ /* MCP55 */
+ dev = dev_find_slot(bus_mcp55[0], PCI_DEVFN(sbdn + 0x06,0));
+ if (dev) {
+ bus_mcp55[1] = pci_read_config8(dev, PCI_SECONDARY_BUS);
+ bus_mcp55[2] = pci_read_config8(dev, PCI_SUBORDINATE_BUS);
+ bus_mcp55[2]++;
+ }
+ else {
+ printk_debug("ERROR - could not find PCI 1:%02x.0, using defaults\n", sbdn + 0x06);
+
+ bus_mcp55[1] = 2;
+ bus_mcp55[2] = 3;
+ }
+
+ for(i=2; i<8;i++) {
+ dev = dev_find_slot(bus_mcp55[0], PCI_DEVFN(sbdn + 0x0a + i - 2 , 0));
+ if (dev) {
+ bus_mcp55[i] = pci_read_config8(dev, PCI_SECONDARY_BUS);
+ bus_isa = pci_read_config8(dev, PCI_SUBORDINATE_BUS);
+ bus_isa++;
+ }
+ else {
+ printk_debug("ERROR - could not find PCI %02x:%02x.0, using defaults\n", bus_mcp55[0], sbdn + 0x0a + i - 2 );
+ bus_isa = bus_mcp55[i-1]+1;
+ }
+ }
+
+ if(bus_mcp55[2]) {
+ for(i=0;i<2; i++) {
+ dev = dev_find_slot(bus_mcp55[2], PCI_DEVFN(0, i));
+ if(dev) {
+ bus_pcix[0] = bus_mcp55[2];
+ bus_pcix[i+1] = pci_read_config8(dev, PCI_SECONDARY_BUS);
+ }
+ }
+ }
+
+
+/*I/O APICs: APIC ID Version State Address*/
+#if CONFIG_LOGICAL_CPUS==1
+ apicid_base = get_apicid_base(1);
+#else
+ apicid_base = CONFIG_MAX_PHYSICAL_CPUS;
+#endif
+ apicid_mcp55 = apicid_base+0;
+
+}
diff --git a/src/mainboard/supermicro/h8dme/irq_tables.c b/src/mainboard/supermicro/h8dme/irq_tables.c
new file mode 100644
index 0000000000..49c7c99b22
--- /dev/null
+++ b/src/mainboard/supermicro/h8dme/irq_tables.c
@@ -0,0 +1,119 @@
+/*
+ * This file is part of the coreboot project.
+ *
+ * Copyright (C) 2007 AMD
+ * Written by Yinghai Lu <yinghailu@amd.com> for AMD.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+/* This file was generated by getpir.c, do not modify!
+ (but if you do, please run checkpir on it to verify)
+ Contains the IRQ Routing Table dumped directly from your memory , wich BIOS sets up
+
+ Documentation at : http://www.microsoft.com/hwdev/busbios/PCIIRQ.HTM
+*/
+#include <console/console.h>
+#include <device/pci.h>
+#include <string.h>
+#include <stdint.h>
+#include <arch/pirq_routing.h>
+
+#include <cpu/amd/amdk8_sysconf.h>
+
+static void write_pirq_info(struct irq_info *pirq_info, uint8_t bus, uint8_t devfn, uint8_t link0, uint16_t bitmap0,
+ uint8_t link1, uint16_t bitmap1, uint8_t link2, uint16_t bitmap2,uint8_t link3, uint16_t bitmap3,
+ uint8_t slot, uint8_t rfu)
+{
+ pirq_info->bus = bus;
+ pirq_info->devfn = devfn;
+ pirq_info->irq[0].link = link0;
+ pirq_info->irq[0].bitmap = bitmap0;
+ pirq_info->irq[1].link = link1;
+ pirq_info->irq[1].bitmap = bitmap1;
+ pirq_info->irq[2].link = link2;
+ pirq_info->irq[2].bitmap = bitmap2;
+ pirq_info->irq[3].link = link3;
+ pirq_info->irq[3].bitmap = bitmap3;
+ pirq_info->slot = slot;
+ pirq_info->rfu = rfu;
+}
+extern unsigned char bus_isa;
+extern unsigned char bus_mcp55[8]; //1
+
+extern void get_bus_conf(void);
+
+unsigned long write_pirq_routing_table(unsigned long addr)
+{
+
+ struct irq_routing_table *pirq;
+ struct irq_info *pirq_info;
+ unsigned slot_num;
+ uint8_t *v;
+ unsigned sbdn;
+
+ uint8_t sum=0;
+ int i;
+
+ get_bus_conf(); // it will find out all bus num and apic that share with mptable.c and mptable.c and acpi_tables.c
+ sbdn = sysconf.sbdn;
+
+ /* Align the table to be 16 byte aligned. */
+ addr += 15;
+ addr &= ~15;
+
+ /* This table must be betweeen 0xf0000 & 0x100000 */
+ printk_info("Writing IRQ routing tables to 0x%x...", addr);
+
+ pirq = (void *)(addr);
+ v = (uint8_t *)(addr);
+
+ pirq->signature = PIRQ_SIGNATURE;
+ pirq->version = PIRQ_VERSION;
+
+ pirq->rtr_bus = bus_mcp55[0];
+ pirq->rtr_devfn = ((sbdn+6)<<3)|0;
+
+ pirq->exclusive_irqs = 0;
+
+ pirq->rtr_vendor = 0x10de;
+ pirq->rtr_device = 0x0370;
+
+ pirq->miniport_data = 0;
+
+ memset(pirq->rfu, 0, sizeof(pirq->rfu));
+
+ pirq_info = (void *) ( &pirq->checksum + 1);
+ slot_num = 0;
+//pci bridge
+ write_pirq_info(pirq_info, bus_mcp55[0], ((sbdn+6)<<3)|0, 0x1, 0xdef8, 0x2, 0xdef8, 0x3, 0xdef8, 0x4, 0xdef8, 0, 0);
+ pirq_info++; slot_num++;
+
+ pirq->size = 32 + 16 * slot_num;
+
+ for (i = 0; i < pirq->size; i++)
+ sum += v[i];
+
+ sum = pirq->checksum - sum;
+
+ if (sum != pirq->checksum) {
+ pirq->checksum = sum;
+ }
+
+ printk_info("done.\n");
+
+ return (unsigned long) pirq_info;
+
+}
diff --git a/src/mainboard/supermicro/h8dme/mainboard.c b/src/mainboard/supermicro/h8dme/mainboard.c
new file mode 100644
index 0000000000..6098ee4b27
--- /dev/null
+++ b/src/mainboard/supermicro/h8dme/mainboard.c
@@ -0,0 +1,30 @@
+/*
+ * This file is part of the coreboot project.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+#include <console/console.h>
+#include <device/device.h>
+#include <device/pci.h>
+#include <device/pci_ids.h>
+#include <device/pci_ops.h>
+#include "chip.h"
+
+#if CONFIG_CHIP_NAME == 1
+struct chip_operations mainboard_ops = {
+ CHIP_NAME("Supermicro H8DME Mainboard")
+};
+#endif
diff --git a/src/mainboard/supermicro/h8dme/mptable.c b/src/mainboard/supermicro/h8dme/mptable.c
new file mode 100644
index 0000000000..e611b9a622
--- /dev/null
+++ b/src/mainboard/supermicro/h8dme/mptable.c
@@ -0,0 +1,175 @@
+/*
+ * This file is part of the coreboot project.
+ *
+ * Copyright (C) 2007 AMD
+ * Written by Yinghai Lu <yinghailu@amd.com> for AMD.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+#include <console/console.h>
+#include <arch/smp/mpspec.h>
+#include <device/pci.h>
+#include <string.h>
+#include <stdint.h>
+
+#include <cpu/amd/amdk8_sysconf.h>
+extern unsigned char bus_isa;
+extern unsigned char bus_mcp55[8]; //1
+
+extern unsigned apicid_mcp55;
+
+extern unsigned char bus_pcix[3]; // under bus_mcp55_2
+
+extern void get_bus_conf(void);
+
+void *smp_write_config_table(void *v)
+{
+ static const char sig[4] = "PCMP";
+ static const char oem[8] = "SUPERMIC";
+ static const char productid[12] = "H8DMR ";
+ struct mp_config_table *mc;
+ unsigned sbdn;
+
+ unsigned char bus_num;
+ int i,j;
+
+ mc = (void *)(((char *)v) + SMP_FLOATING_TABLE_LEN);
+ memset(mc, 0, sizeof(*mc));
+
+ memcpy(mc->mpc_signature, sig, sizeof(sig));
+ mc->mpc_length = sizeof(*mc); /* initially just the header */
+ mc->mpc_spec = 0x04;
+ mc->mpc_checksum = 0; /* not yet computed */
+ memcpy(mc->mpc_oem, oem, sizeof(oem));
+ memcpy(mc->mpc_productid, productid, sizeof(productid));
+ mc->mpc_oemptr = 0;
+ mc->mpc_oemsize = 0;
+ mc->mpc_entry_count = 0; /* No entries yet... */
+ mc->mpc_lapic = LAPIC_ADDR;
+ mc->mpe_length = 0;
+ mc->mpe_checksum = 0;
+ mc->reserved = 0;
+
+ smp_write_processors(mc);
+
+ get_bus_conf();
+ sbdn = sysconf.sbdn;
+
+/*Bus: Bus ID Type*/
+ /* define bus and isa numbers */
+ for(bus_num = 0; bus_num < bus_isa; bus_num++) {
+ smp_write_bus(mc, bus_num, "PCI ");
+ }
+ smp_write_bus(mc, bus_isa, "ISA ");
+
+/*I/O APICs: APIC ID Version State Address*/
+ {
+ device_t dev;
+ struct resource *res;
+ uint32_t dword;
+
+ dev = dev_find_slot(bus_mcp55[0], PCI_DEVFN(sbdn+ 0x1,0));
+ if (dev) {
+ res = find_resource(dev, PCI_BASE_ADDRESS_1);
+ if (res) {
+ smp_write_ioapic(mc, apicid_mcp55, 0x11, res->base);
+ }
+
+ dword = 0x43c6c643;
+ pci_write_config32(dev, 0x7c, dword);
+
+ dword = 0x81001a00;
+ pci_write_config32(dev, 0x80, dword);
+
+ dword = 0xd00012d2;
+ pci_write_config32(dev, 0x84, dword);
+
+ }
+
+
+
+ }
+
+/*I/O Ints: Type Polarity Trigger Bus ID IRQ APIC ID PIN#
+*/ smp_write_intsrc(mc, mp_ExtINT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, bus_isa, 0x0, apicid_mcp55, 0x0);
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, bus_isa, 0x1, apicid_mcp55, 0x1);
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, bus_isa, 0x0, apicid_mcp55, 0x2);
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, bus_isa, 0x3, apicid_mcp55, 0x3);
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, bus_isa, 0x4, apicid_mcp55, 0x4);
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, bus_isa, 0x6, apicid_mcp55, 0x6);
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, bus_isa, 0x7, apicid_mcp55, 0x7);
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, bus_isa, 0x8, apicid_mcp55, 0x8);
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, bus_isa, 0xc, apicid_mcp55, 0xc);
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, bus_isa, 0xd, apicid_mcp55, 0xd);
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, bus_isa, 0xe, apicid_mcp55, 0xe);
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, bus_isa, 0xf, apicid_mcp55, 0xf);
+
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_mcp55[0], ((sbdn+1)<<2)|1, apicid_mcp55, 0xa);
+
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_mcp55[0], ((sbdn+2)<<2)|0, apicid_mcp55, 0x16); // 22
+
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_mcp55[0], ((sbdn+2)<<2)|1, apicid_mcp55, 0x17); // 23
+
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_mcp55[0], ((sbdn+6)<<2)|1, apicid_mcp55, 0x17); // 23
+
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_mcp55[0], ((sbdn+5)<<2)|0, apicid_mcp55, 0x14); // 20
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_mcp55[0], ((sbdn+5)<<2)|1, apicid_mcp55, 0x17); // 23
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_mcp55[0], ((sbdn+5)<<2)|2, apicid_mcp55, 0x15); // 21
+
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_mcp55[0], ((sbdn+8)<<2)|0, apicid_mcp55, 0x16); // 22
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_mcp55[0], ((sbdn+9)<<2)|0, apicid_mcp55, 0x15); // 21
+
+ for(j=7; j>=2; j--) {
+ if(!bus_mcp55[j]) continue;
+ for(i=0;i<4;i++) {
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_mcp55[j], (0x00<<2)|i, apicid_mcp55, 0x10 + (2+j+i+4-sbdn%4)%4);
+ }
+ }
+
+ for(i=0;i<4;i++) {
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_mcp55[1], (0x04<<2)|i, apicid_mcp55, 0x10 + (0+i)%4);
+ }
+
+
+ if(bus_pcix[0]) {
+ for(i=0;i<2;i++) {
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_pcix[2], (4<<2)|i, apicid_mcp55, 0x10 + (0+i+4-sbdn%4)%4); //16, 17
+ }
+
+ for(i=0;i<4;i++) {
+ smp_write_intsrc(mc, mp_INT, MP_IRQ_TRIGGER_LEVEL|MP_IRQ_POLARITY_LOW, bus_pcix[1], (4<<2)|i, apicid_mcp55, 0x10 + (2+i+4-sbdn%4)%4); // 18, 19, 16, 17
+ }
+ }
+
+/*Local Ints: Type Polarity Trigger Bus ID IRQ APIC ID PIN#*/
+ smp_write_intsrc(mc, mp_ExtINT, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, bus_isa, 0x0, MP_APIC_ALL, 0x0);
+ smp_write_intsrc(mc, mp_NMI, MP_IRQ_TRIGGER_EDGE|MP_IRQ_POLARITY_HIGH, bus_isa, 0x0, MP_APIC_ALL, 0x1);
+ /* There is no extension information... */
+
+ /* Compute the checksums */
+ mc->mpe_checksum = smp_compute_checksum(smp_next_mpc_entry(mc), mc->mpe_length);
+ mc->mpc_checksum = smp_compute_checksum(mc, mc->mpc_length);
+ printk_debug("Wrote the mp table end at: %p - %p\n",
+ mc, smp_next_mpe_entry(mc));
+ return smp_next_mpe_entry(mc);
+}
+
+unsigned long write_smp_table(unsigned long addr)
+{
+ void *v;
+ v = smp_write_floating_table(addr);
+ return (unsigned long)smp_write_config_table(v);
+}
diff --git a/src/mainboard/supermicro/h8dme/resourcemap.c b/src/mainboard/supermicro/h8dme/resourcemap.c
new file mode 100644
index 0000000000..fa22ee337b
--- /dev/null
+++ b/src/mainboard/supermicro/h8dme/resourcemap.c
@@ -0,0 +1,283 @@
+/*
+ * This file is part of the coreboot project.
+ *
+ * Copyright (C) 2007 AMD
+ * Written by Yinghai Lu <yinghailu@amd.com> for AMD.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+static void setup_mb_resource_map(void)
+{
+ static const unsigned int register_values[] = {
+ /* Careful set limit registers before base registers which contain the enables */
+ /* DRAM Limit i Registers
+ * F1:0x44 i = 0
+ * F1:0x4C i = 1
+ * F1:0x54 i = 2
+ * F1:0x5C i = 3
+ * F1:0x64 i = 4
+ * F1:0x6C i = 5
+ * F1:0x74 i = 6
+ * F1:0x7C i = 7
+ * [ 2: 0] Destination Node ID
+ * 000 = Node 0
+ * 001 = Node 1
+ * 010 = Node 2
+ * 011 = Node 3
+ * 100 = Node 4
+ * 101 = Node 5
+ * 110 = Node 6
+ * 111 = Node 7
+ * [ 7: 3] Reserved
+ * [10: 8] Interleave select
+ * specifies the values of A[14:12] to use with interleave enable.
+ * [15:11] Reserved
+ * [31:16] DRAM Limit Address i Bits 39-24
+ * This field defines the upper address bits of a 40 bit address
+ * that define the end of the DRAM region.
+ */
+ PCI_ADDR(0, 0x18, 1, 0x44), 0x0000f8f8, 0x00000000,
+ PCI_ADDR(0, 0x18, 1, 0x4C), 0x0000f8f8, 0x00000001,
+ PCI_ADDR(0, 0x18, 1, 0x54), 0x0000f8f8, 0x00000002,
+ PCI_ADDR(0, 0x18, 1, 0x5C), 0x0000f8f8, 0x00000003,
+ PCI_ADDR(0, 0x18, 1, 0x64), 0x0000f8f8, 0x00000004,
+ PCI_ADDR(0, 0x18, 1, 0x6C), 0x0000f8f8, 0x00000005,
+ PCI_ADDR(0, 0x18, 1, 0x74), 0x0000f8f8, 0x00000006,
+ PCI_ADDR(0, 0x18, 1, 0x7C), 0x0000f8f8, 0x00000007,
+
+ /* DRAM Base i Registers
+ * F1:0x40 i = 0
+ * F1:0x48 i = 1
+ * F1:0x50 i = 2
+ * F1:0x58 i = 3
+ * F1:0x60 i = 4
+ * F1:0x68 i = 5
+ * F1:0x70 i = 6
+ * F1:0x78 i = 7
+ * [ 0: 0] Read Enable
+ * 0 = Reads Disabled
+ * 1 = Reads Enabled
+ * [ 1: 1] Write Enable
+ * 0 = Writes Disabled
+ * 1 = Writes Enabled
+ * [ 7: 2] Reserved
+ * [10: 8] Interleave Enable
+ * 000 = No interleave
+ * 001 = Interleave on A[12] (2 nodes)
+ * 010 = reserved
+ * 011 = Interleave on A[12] and A[14] (4 nodes)
+ * 100 = reserved
+ * 101 = reserved
+ * 110 = reserved
+ * 111 = Interleve on A[12] and A[13] and A[14] (8 nodes)
+ * [15:11] Reserved
+ * [13:16] DRAM Base Address i Bits 39-24
+ * This field defines the upper address bits of a 40-bit address
+ * that define the start of the DRAM region.
+ */
+ PCI_ADDR(0, 0x18, 1, 0x40), 0x0000f8fc, 0x00000000,
+ PCI_ADDR(0, 0x18, 1, 0x48), 0x0000f8fc, 0x00000000,
+ PCI_ADDR(0, 0x18, 1, 0x50), 0x0000f8fc, 0x00000000,
+ PCI_ADDR(0, 0x18, 1, 0x58), 0x0000f8fc, 0x00000000,
+ PCI_ADDR(0, 0x18, 1, 0x60), 0x0000f8fc, 0x00000000,
+ PCI_ADDR(0, 0x18, 1, 0x68), 0x0000f8fc, 0x00000000,
+ PCI_ADDR(0, 0x18, 1, 0x70), 0x0000f8fc, 0x00000000,
+ PCI_ADDR(0, 0x18, 1, 0x78), 0x0000f8fc, 0x00000000,
+
+ /* Memory-Mapped I/O Limit i Registers
+ * F1:0x84 i = 0
+ * F1:0x8C i = 1
+ * F1:0x94 i = 2
+ * F1:0x9C i = 3
+ * F1:0xA4 i = 4
+ * F1:0xAC i = 5
+ * F1:0xB4 i = 6
+ * F1:0xBC i = 7
+ * [ 2: 0] Destination Node ID
+ * 000 = Node 0
+ * 001 = Node 1
+ * 010 = Node 2
+ * 011 = Node 3
+ * 100 = Node 4
+ * 101 = Node 5
+ * 110 = Node 6
+ * 111 = Node 7
+ * [ 3: 3] Reserved
+ * [ 5: 4] Destination Link ID
+ * 00 = Link 0
+ * 01 = Link 1
+ * 10 = Link 2
+ * 11 = Reserved
+ * [ 6: 6] Reserved
+ * [ 7: 7] Non-Posted
+ * 0 = CPU writes may be posted
+ * 1 = CPU writes must be non-posted
+ * [31: 8] Memory-Mapped I/O Limit Address i (39-16)
+ * This field defines the upp adddress bits of a 40-bit address that
+ * defines the end of a memory-mapped I/O region n
+ */
+ PCI_ADDR(0, 0x18, 1, 0x84), 0x00000048, 0x00000000,
+ PCI_ADDR(0, 0x18, 1, 0x8C), 0x00000048, 0x00000000,
+ PCI_ADDR(0, 0x18, 1, 0x94), 0x00000048, 0x00000000,
+ PCI_ADDR(0, 0x18, 1, 0x9C), 0x00000048, 0x00000000,
+ PCI_ADDR(0, 0x18, 1, 0xA4), 0x00000048, 0x00000000,
+ PCI_ADDR(0, 0x18, 1, 0xAC), 0x00000048, 0x00000000,
+ PCI_ADDR(0, 0x18, 1, 0xB4), 0x00000048, 0x00000000,
+// PCI_ADDR(0, 0x18, 1, 0xBC), 0x00000048, 0x00ffff00,
+
+ /* Memory-Mapped I/O Base i Registers
+ * F1:0x80 i = 0
+ * F1:0x88 i = 1
+ * F1:0x90 i = 2
+ * F1:0x98 i = 3
+ * F1:0xA0 i = 4
+ * F1:0xA8 i = 5
+ * F1:0xB0 i = 6
+ * F1:0xB8 i = 7
+ * [ 0: 0] Read Enable
+ * 0 = Reads disabled
+ * 1 = Reads Enabled
+ * [ 1: 1] Write Enable
+ * 0 = Writes disabled
+ * 1 = Writes Enabled
+ * [ 2: 2] Cpu Disable
+ * 0 = Cpu can use this I/O range
+ * 1 = Cpu requests do not use this I/O range
+ * [ 3: 3] Lock
+ * 0 = base/limit registers i are read/write
+ * 1 = base/limit registers i are read-only
+ * [ 7: 4] Reserved
+ * [31: 8] Memory-Mapped I/O Base Address i (39-16)
+ * This field defines the upper address bits of a 40bit address
+ * that defines the start of memory-mapped I/O region i
+ */
+ PCI_ADDR(0, 0x18, 1, 0x80), 0x000000f0, 0x00000000,
+ PCI_ADDR(0, 0x18, 1, 0x88), 0x000000f0, 0x00000000,
+ PCI_ADDR(0, 0x18, 1, 0x90), 0x000000f0, 0x00000000,
+ PCI_ADDR(0, 0x18, 1, 0x98), 0x000000f0, 0x00000000,
+ PCI_ADDR(0, 0x18, 1, 0xA0), 0x000000f0, 0x00000000,
+ PCI_ADDR(0, 0x18, 1, 0xA8), 0x000000f0, 0x00000000,
+ PCI_ADDR(0, 0x18, 1, 0xB0), 0x000000f0, 0x00000000,
+// PCI_ADDR(0, 0x18, 1, 0xB8), 0x000000f0, 0x00fc0003,
+
+ /* PCI I/O Limit i Registers
+ * F1:0xC4 i = 0
+ * F1:0xCC i = 1
+ * F1:0xD4 i = 2
+ * F1:0xDC i = 3
+ * [ 2: 0] Destination Node ID
+ * 000 = Node 0
+ * 001 = Node 1
+ * 010 = Node 2
+ * 011 = Node 3
+ * 100 = Node 4
+ * 101 = Node 5
+ * 110 = Node 6
+ * 111 = Node 7
+ * [ 3: 3] Reserved
+ * [ 5: 4] Destination Link ID
+ * 00 = Link 0
+ * 01 = Link 1
+ * 10 = Link 2
+ * 11 = reserved
+ * [11: 6] Reserved
+ * [24:12] PCI I/O Limit Address i
+ * This field defines the end of PCI I/O region n
+ * [31:25] Reserved
+ */
+ PCI_ADDR(0, 0x18, 1, 0xC4), 0xFE000FC8, 0x01fff020,
+ PCI_ADDR(0, 0x18, 1, 0xCC), 0xFE000FC8, 0x00000000, // need to talk to ANALOG of second CK804 to release PCI E reset
+ PCI_ADDR(0, 0x18, 1, 0xD4), 0xFE000FC8, 0x00000000,
+ PCI_ADDR(0, 0x18, 1, 0xDC), 0xFE000FC8, 0x00000000,
+
+ /* PCI I/O Base i Registers
+ * F1:0xC0 i = 0
+ * F1:0xC8 i = 1
+ * F1:0xD0 i = 2
+ * F1:0xD8 i = 3
+ * [ 0: 0] Read Enable
+ * 0 = Reads Disabled
+ * 1 = Reads Enabled
+ * [ 1: 1] Write Enable
+ * 0 = Writes Disabled
+ * 1 = Writes Enabled
+ * [ 3: 2] Reserved
+ * [ 4: 4] VGA Enable
+ * 0 = VGA matches Disabled
+ * 1 = matches all address < 64K and where A[9:0] is in the
+ * range 3B0-3BB or 3C0-3DF independen of the base & limit registers
+ * [ 5: 5] ISA Enable
+ * 0 = ISA matches Disabled
+ * 1 = Blocks address < 64K and in the last 768 bytes of eack 1K block
+ * from matching agains this base/limit pair
+ * [11: 6] Reserved
+ * [24:12] PCI I/O Base i
+ * This field defines the start of PCI I/O region n
+ * [31:25] Reserved
+ */
+ PCI_ADDR(0, 0x18, 1, 0xC0), 0xFE000FCC, 0x00000033,
+ PCI_ADDR(0, 0x18, 1, 0xC8), 0xFE000FCC, 0x00000000,
+ PCI_ADDR(0, 0x18, 1, 0xD0), 0xFE000FCC, 0x00000000,
+ PCI_ADDR(0, 0x18, 1, 0xD8), 0xFE000FCC, 0x00000000,
+
+ /* Config Base and Limit i Registers
+ * F1:0xE0 i = 0
+ * F1:0xE4 i = 1
+ * F1:0xE8 i = 2
+ * F1:0xEC i = 3
+ * [ 0: 0] Read Enable
+ * 0 = Reads Disabled
+ * 1 = Reads Enabled
+ * [ 1: 1] Write Enable
+ * 0 = Writes Disabled
+ * 1 = Writes Enabled
+ * [ 2: 2] Device Number Compare Enable
+ * 0 = The ranges are based on bus number
+ * 1 = The ranges are ranges of devices on bus 0
+ * [ 3: 3] Reserved
+ * [ 6: 4] Destination Node
+ * 000 = Node 0
+ * 001 = Node 1
+ * 010 = Node 2
+ * 011 = Node 3
+ * 100 = Node 4
+ * 101 = Node 5
+ * 110 = Node 6
+ * 111 = Node 7
+ * [ 7: 7] Reserved
+ * [ 9: 8] Destination Link
+ * 00 = Link 0
+ * 01 = Link 1
+ * 10 = Link 2
+ * 11 - Reserved
+ * [15:10] Reserved
+ * [23:16] Bus Number Base i
+ * This field defines the lowest bus number in configuration region i
+ * [31:24] Bus Number Limit i
+ * This field defines the highest bus number in configuration region i
+ */
+ PCI_ADDR(0, 0x18, 1, 0xE0), 0x0000FC88, 0x3f000203, /* link 2 of cpu 0 --> Nvidia MCP55 Pro */
+ PCI_ADDR(0, 0x18, 1, 0xE4), 0x0000FC88, 0x00000000,
+ PCI_ADDR(0, 0x18, 1, 0xE8), 0x0000FC88, 0x00000000,
+ PCI_ADDR(0, 0x18, 1, 0xEC), 0x0000FC88, 0x00000000,
+
+ };
+
+ int max;
+ max = ARRAY_SIZE(register_values);
+ setup_resource_map(register_values, max);
+}
+