diff options
Diffstat (limited to 'src/mainboard/olpc/rev_a')
| -rw-r--r-- | src/mainboard/olpc/rev_a/devicetree.cb | 4 | ||||
| -rw-r--r-- | src/mainboard/olpc/rev_a/irq_tables.c | 2 | ||||
| -rw-r--r-- | src/mainboard/olpc/rev_a/mainboard.c | 2 | ||||
| -rw-r--r-- | src/mainboard/olpc/rev_a/romstage.c | 16 |
4 files changed, 12 insertions, 12 deletions
diff --git a/src/mainboard/olpc/rev_a/devicetree.cb b/src/mainboard/olpc/rev_a/devicetree.cb index e0da82836a..ca55ce1b7e 100644 --- a/src/mainboard/olpc/rev_a/devicetree.cb +++ b/src/mainboard/olpc/rev_a/devicetree.cb @@ -6,7 +6,7 @@ chip northbridge/amd/gx2 device apic 0 on end end end - device pci_domain 0 on + device pci_domain 0 on device pci 1.0 on end device pci 1.1 on end chip southbridge/amd/cs5536 @@ -18,7 +18,7 @@ chip northbridge/amd/gx2 # SIRQ Mode = continous , It would be better if the EC could operate in # Active(Quiet) mode. Save power.... # SIRQ Enable = Enabled - # Invert mask = IRQ 12 and 1 are active high. Keyboard and Mouse IRQs. OK + # Invert mask = IRQ 12 and 1 are active high. Keyboard and Mouse IRQs. OK #register "lpc_irq" = "0x00001002" #register "lpc_serirq_enable" = "0xEFFD0080" #register "enable_gpio0_inta" = "1" diff --git a/src/mainboard/olpc/rev_a/irq_tables.c b/src/mainboard/olpc/rev_a/irq_tables.c index 598350b4b8..f751b481ca 100644 --- a/src/mainboard/olpc/rev_a/irq_tables.c +++ b/src/mainboard/olpc/rev_a/irq_tables.c @@ -1,4 +1,4 @@ -/* This file was generated by getpir.c, do not modify! +/* This file was generated by getpir.c, do not modify! (but if you do, please run checkpir on it to verify) * Contains the IRQ Routing Table dumped directly from your memory, which BIOS sets up * diff --git a/src/mainboard/olpc/rev_a/mainboard.c b/src/mainboard/olpc/rev_a/mainboard.c index a02e583558..adfb957ab7 100644 --- a/src/mainboard/olpc/rev_a/mainboard.c +++ b/src/mainboard/olpc/rev_a/mainboard.c @@ -83,7 +83,7 @@ static void init(struct device *dev) { * conditional we can make it a config variable later. */ - printk(BIOS_DEBUG, "%s (%x,%x)SET USB PCI interrupt line to %d\n", + printk(BIOS_DEBUG, "%s (%x,%x)SET USB PCI interrupt line to %d\n", __func__, bus, devfn, usbirq); usb = dev_find_slot(bus, devfn); if (! usb){ diff --git a/src/mainboard/olpc/rev_a/romstage.c b/src/mainboard/olpc/rev_a/romstage.c index 1503baa6ba..fc605d1a88 100644 --- a/src/mainboard/olpc/rev_a/romstage.c +++ b/src/mainboard/olpc/rev_a/romstage.c @@ -50,7 +50,7 @@ static inline unsigned int fls(unsigned int x) Trrd=2 (act2act) Tref=17.8ms */ -static void sdram_set_spd_registers(const struct mem_controller *ctrl) +static void sdram_set_spd_registers(const struct mem_controller *ctrl) { /* Total size of DIMM = 2^row address (byte 3) * 2^col address (byte 4) * * component Banks (byte 17) * module banks, side (byte 5) * @@ -100,11 +100,11 @@ static void sdram_set_spd_registers(const struct mem_controller *ctrl) /* timing and mode ... */ msr = rdmsr(0x20000019); - - /* per standard bios settings */ + + /* per standard bios settings */ msr.hi = 0x18000108; - msr.lo = + msr.lo = (6<<28) | // cas_lat (10<<24)| // ref2act (7<<20)| // act2pre @@ -114,8 +114,8 @@ static void sdram_set_spd_registers(const struct mem_controller *ctrl) (2<<6)| // dplwr (2<<4)| // dplrd (3); // dal - /* the msr value reported by quanta is very, very different. - * we will go with that value for now. + /* the msr value reported by quanta is very, very different. + * we will go with that value for now. */ msr.lo = 0x286332a3; @@ -180,9 +180,9 @@ static void main(unsigned long bist) cpuRegInit(); print_err("done cpuRegInit\n"); - + sdram_initialize(1, memctrl); - + /* Check all of memory */ //ram_check(0x00000000, 640*1024); } |