diff options
Diffstat (limited to 'src/mainboard/lippert/spacerunner-lx/romstage.c')
-rw-r--r-- | src/mainboard/lippert/spacerunner-lx/romstage.c | 181 |
1 files changed, 0 insertions, 181 deletions
diff --git a/src/mainboard/lippert/spacerunner-lx/romstage.c b/src/mainboard/lippert/spacerunner-lx/romstage.c deleted file mode 100644 index a8885700ef..0000000000 --- a/src/mainboard/lippert/spacerunner-lx/romstage.c +++ /dev/null @@ -1,181 +0,0 @@ -/* - * This file is part of the coreboot project. - * - * Copyright (C) 2007 Advanced Micro Devices, Inc. - * Copyright (C) 2008 LiPPERT Embedded Computers GmbH - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - */ - -/* Based on romstage.c from AMD's DB800 and DBM690T mainboards. */ - -#include <stdlib.h> -#include <stdint.h> -#include <spd.h> -#include <device/pci_def.h> -#include <arch/io.h> -#include <device/pnp_def.h> -#include <console/console.h> -#include <cpu/x86/bist.h> -#include <cpu/x86/msr.h> -#include <cpu/amd/lxdef.h> -#include <southbridge/amd/cs5536/cs5536.h> -#include <southbridge/amd/cs5536/smbus.h> -#include <superio/ite/common/ite.h> -#include <superio/ite/it8712f/it8712f.h> -#include <northbridge/amd/lx/raminit.h> - -#define SERIAL_DEV PNP_DEV(0x2e, IT8712F_SP1) -#define GPIO_DEV PNP_DEV(0x2e, IT8712F_GPIO) - -/* Bit0 enables Spread Spectrum, bit1 makes on-board SSD act as IDE slave. */ -#if IS_ENABLED(CONFIG_ONBOARD_IDE_SLAVE) - #define SMC_CONFIG 0x03 -#else - #define SMC_CONFIG 0x01 -#endif - -static const unsigned char spdbytes[] = { // 4x Promos V58C2512164SA-J5I - 0xFF, 0xFF, // only values used by Geode-LX raminit.c are set - [SPD_MEMORY_TYPE] = SPD_MEMORY_TYPE_SDRAM_DDR, // (Fundamental) memory type - [SPD_NUM_ROWS] = 0x0D, // Number of row address bits [13] - [SPD_NUM_COLUMNS] = 0x0A, // Number of column address bits [10] - [SPD_NUM_DIMM_BANKS] = 1, // Number of module rows (banks) - 0xFF, 0xFF, 0xFF, - [SPD_MIN_CYCLE_TIME_AT_CAS_MAX] = 0x50, // SDRAM cycle time (highest CAS latency), RAS access time (tRAC) [5.0 ns in BCD] - 0xFF, 0xFF, - [SPD_REFRESH] = 0x82, // Refresh rate/type [Self Refresh, 7.8 us] - [SPD_PRIMARY_SDRAM_WIDTH] = 64, // SDRAM width (primary SDRAM) [64 bits] - 0xFF, 0xFF, 0xFF, - [SPD_NUM_BANKS_PER_SDRAM] = 4, // SDRAM device attributes, number of banks on SDRAM device - [SPD_ACCEPTABLE_CAS_LATENCIES] = 0x1C, // SDRAM device attributes, CAS latency [3, 2.5, 2] - 0xFF, 0xFF, - [SPD_MODULE_ATTRIBUTES] = 0x20, // SDRAM module attributes [differential clk] - [SPD_DEVICE_ATTRIBUTES_GENERAL] = 0x40, // SDRAM device attributes, general [Concurrent AP] - [SPD_SDRAM_CYCLE_TIME_2ND] = 0x60, // SDRAM cycle time (2nd highest CAS latency) [6.0 ns in BCD] - 0xFF, - [SPD_SDRAM_CYCLE_TIME_3RD] = 0x75, // SDRAM cycle time (3rd highest CAS latency) [7.5 ns in BCD] - 0xFF, - [SPD_tRP] = 60, // Min. row precharge time [15 ns in units of 0.25 ns] - [SPD_tRRD] = 40, // Min. row active to row active [10 ns in units of 0.25 ns] - [SPD_tRCD] = 60, // Min. RAS to CAS delay [15 ns in units of 0.25 ns] - [SPD_tRAS] = 40, // Min. RAS pulse width = active to precharge delay [40 ns] - [SPD_BANK_DENSITY] = 0x40, // Density of each row on module [256 MB] - 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, - [SPD_tRFC] = 70 // SDRAM Device Minimum Auto Refresh to Active/Auto Refresh [70 ns] -}; - -int spd_read_byte(unsigned int device, unsigned int address) -{ - if (device != DIMM0) - return 0xFF; /* No DIMM1, don't even try. */ - -#if IS_ENABLED(CONFIG_DEBUG_SMBUS) - if (address >= sizeof(spdbytes) || spdbytes[address] == 0xFF) { - printk(BIOS_ERR, "ERROR: spd_read_byte(DIMM0, 0x%02x) " - "returns 0xff\n", address); - } -#endif - - /* Fake SPD ROM value */ - return (address < sizeof(spdbytes)) ? spdbytes[address] : 0xFF; -} - -/* Send config data to System Management Controller via SMB. */ -static int smc_send_config(unsigned char config_data) -{ - if (smbus_check_stop_condition(SMBUS_IO_BASE)) - return 1; - if (smbus_start_condition(SMBUS_IO_BASE)) - return 2; - if (smbus_send_slave_address(SMBUS_IO_BASE, 0x50)) // SMC address - return 3; - if (smbus_send_command(SMBUS_IO_BASE, 0x28)) // set config data - return 4; - if (smbus_send_command(SMBUS_IO_BASE, 0x01)) // data length - return 5; - if (smbus_send_command(SMBUS_IO_BASE, config_data)) - return 6; - smbus_stop_condition(SMBUS_IO_BASE); - return 0; -} - -#include "northbridge/amd/lx/pll_reset.c" -#include "cpu/amd/geode_lx/cpureginit.c" -#include "cpu/amd/geode_lx/syspreinit.c" -#include "cpu/amd/geode_lx/msrinit.c" - -static const u16 sio_init_table[] = { // hi = data, lo = index - 0x072C, // VIN6 enabled, FAN4/5 disabled, VIN7,VIN3 internal - 0x1423, // don't delay PoWeROK1/2 - 0x9072, // watchdog triggers PWROK, counts seconds -#if !IS_ENABLED(CONFIG_USE_WATCHDOG_ON_BOOT) - 0x0073, 0x0074, // disarm watchdog by changing 56 s timeout to 0 -#endif - 0xBF25, 0x172A, 0xF326, // select GPIO function for most pins - 0xFF27, 0xDF28, 0x2729, // (GP45 = SUSB, GP23,22,16,15 = SPI, GP13 = PWROK1) - 0x66B8, 0x0CB9, // enable pullups on SPI, RS485_EN - 0x07C0, // enable Simple-I/O for GP12-10= RS485_EN2,1, LIVE_LED - 0x07C8, // config GP12-10 as output - 0x2DF5, // map Hw Monitor Thermal Output to GP55 - 0x08F8, // map GP LED Blinking 1 to GP10 = LIVE_LED (deactivate Simple I/O to use) -}; - -/* Early mainboard specific GPIO setup. */ -static void mb_gpio_init(void) -{ - int i; - - /* Init Super I/O WDT, GPIOs. Done early, WDT init may trigger reset! */ - for (i = 0; i < ARRAY_SIZE(sio_init_table); i++) { - u16 reg = sio_init_table[i]; - ite_reg_write(GPIO_DEV, (u8) reg, (reg >> 8)); - } -} - -void asmlinkage mainboard_romstage_entry(unsigned long bist) -{ - int err; - - static const struct mem_controller memctrl[] = { - {.channel0 = {DIMM0, DIMM1}} - }; - - SystemPreInit(); - msr_init(); - - cs5536_early_setup(); - - /* - * Note: Must do this AFTER the early_setup! It is counting on some - * early MSR setup for CS5536. - */ - ite_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE); - mb_gpio_init(); - console_init(); - - /* Halt if there was a built in self test failure */ - report_bist_failure(bist); - - pll_reset(); - - cpuRegInit(0, DIMM0, DIMM1, DRAM_TERMINATED); - - /* bit1 = on-board IDE is slave, bit0 = Spread Spectrum */ - if ((err = smc_send_config(SMC_CONFIG))) { - printk(BIOS_ERR, "ERROR %d sending config data to SMC\n", err); - } - - sdram_initialize(1, memctrl); - - /* Memory is setup. Return to cache_as_ram.inc and continue to boot. */ - return; -} |