diff options
Diffstat (limited to 'src/mainboard/iwill/DK8X/Options.lb')
| -rw-r--r-- | src/mainboard/iwill/DK8X/Options.lb | 214 |
1 files changed, 214 insertions, 0 deletions
diff --git a/src/mainboard/iwill/DK8X/Options.lb b/src/mainboard/iwill/DK8X/Options.lb new file mode 100644 index 0000000000..6265e72fe1 --- /dev/null +++ b/src/mainboard/iwill/DK8X/Options.lb @@ -0,0 +1,214 @@ +uses HAVE_MP_TABLE +uses HAVE_PIRQ_TABLE +uses USE_FALLBACK_IMAGE +uses HAVE_FALLBACK_BOOT +uses HAVE_HARD_RESET +uses IRQ_SLOT_COUNT +uses HAVE_OPTION_TABLE +uses CONFIG_MAX_CPUS +uses CONFIG_MAX_PHYSICAL_CPUS +uses CONFIG_IOAPIC +uses CONFIG_SMP +uses FALLBACK_SIZE +uses ROM_SIZE +uses ROM_SECTION_SIZE +uses ROM_IMAGE_SIZE +uses ROM_SECTION_SIZE +uses ROM_SECTION_OFFSET +uses CONFIG_ROM_STREAM +uses CONFIG_ROM_STREAM_START +uses PAYLOAD_SIZE +uses _ROMBASE +uses XIP_ROM_SIZE +uses XIP_ROM_BASE +uses STACK_SIZE +uses HEAP_SIZE +uses USE_OPTION_TABLE +uses LB_CKS_RANGE_START +uses LB_CKS_RANGE_END +uses LB_CKS_LOC +uses MAINBOARD +uses MAINBOARD_PART_NUMBER +uses MAINBOARD_VENDOR +uses MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID +uses MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID +uses LINUXBIOS_EXTRA_VERSION +uses _RAMBASE +uses TTYS0_BAUD +uses TTYS0_BASE +uses TTYS0_LCS +uses DEFAULT_CONSOLE_LOGLEVEL +uses MAXIMUM_CONSOLE_LOGLEVEL +uses MAINBOARD_POWER_ON_AFTER_POWER_FAIL +uses CONFIG_CONSOLE_SERIAL8250 +uses HAVE_INIT_TIMER +uses CONFIG_GDB_STUB +uses CROSS_COMPILE +uses CC +uses HOSTCC +uses OBJCOPY + +uses CONFIG_USE_INIT + +## ROM_SIZE is the size of boot ROM that this board will use. +default ROM_SIZE=524288 + +### +### Build options +### + +## +## FALLBACK_SIZE is the amount of the ROM the complete fallback image will use +## +default FALLBACK_SIZE=131072 + +## +## Build code for the fallback boot +## +default HAVE_FALLBACK_BOOT=1 + +## +## Build code to reset the motherboard from linuxBIOS +## +default HAVE_HARD_RESET=1 + +## +## Build code to export a programmable irq routing table +## +default HAVE_PIRQ_TABLE=1 +default IRQ_SLOT_COUNT=9 + +## +## Build code to export an x86 MP table +## Useful for specifying IRQ routing values +## +default HAVE_MP_TABLE=1 + +## +## Build code to export a CMOS option table +## +default HAVE_OPTION_TABLE=1 + +## +## Move the default LinuxBIOS cmos range off of AMD RTC registers +## +default LB_CKS_RANGE_START=49 +default LB_CKS_RANGE_END=122 +default LB_CKS_LOC=123 + +## +## Build code for SMP support +## Only worry about 2 micro processors +## +default CONFIG_SMP=1 +default CONFIG_MAX_CPUS=2 +default CONFIG_MAX_PHYSICAL_CPUS=2 + +## +## Build code to setup a generic IOAPIC +## +default CONFIG_IOAPIC=1 + +## +## Clean up the motherboard id strings +## +#default MAINBOARD_PART_NUMBER="HDAMA" +#default MAINBOARD_VENDOR="ARIMA" +#default MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x161f +#default MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x3016 + +### +### LinuxBIOS layout values +### + +## ROM_IMAGE_SIZE is the amount of space to allow linuxBIOS to occupy. +default ROM_IMAGE_SIZE = 65536 + +## +## Use a small 8K stack +## +default STACK_SIZE=0x2000 + +## +## Use a small 16K heap +## +default HEAP_SIZE=0x4000 + +## +## Only use the option table in a normal image +## +default USE_OPTION_TABLE = !USE_FALLBACK_IMAGE + +## +## LinuxBIOS C code runs at this location in RAM +## +default _RAMBASE=0x00004000 + +## +## Load the payload from the ROM +## +default CONFIG_ROM_STREAM = 1 + +### +### Defaults of options that you may want to override in the target config file +### + +## +## The default compiler +## +#default CC="$(CROSS_COMPILE)gcc -m32" +#default HOSTCC="gcc" + +## +## Disable the gdb stub by default +## +default CONFIG_GDB_STUB=0 + +## +## The Serial Console +## + +# To Enable the Serial Console +default CONFIG_CONSOLE_SERIAL8250=1 + +## Select the serial console baud rate +default TTYS0_BAUD=115200 +#default TTYS0_BAUD=57600 +#default TTYS0_BAUD=38400 +#default TTYS0_BAUD=19200 +#default TTYS0_BAUD=9600 +#default TTYS0_BAUD=4800 +#default TTYS0_BAUD=2400 +#default TTYS0_BAUD=1200 + +# Select the serial console base port +default TTYS0_BASE=0x3f8 + +# Select the serial protocol +# This defaults to 8 data bits, 1 stop bit, and no parity +default TTYS0_LCS=0x3 + +## +### Select the linuxBIOS loglevel +## +## EMERG 1 system is unusable +## ALERT 2 action must be taken immediately +## CRIT 3 critical conditions +## ERR 4 error conditions +## WARNING 5 warning conditions +## NOTICE 6 normal but significant condition +## INFO 7 informational +## DEBUG 8 debug-level messages +## SPEW 9 Way too many details + +## Request this level of debugging output +default DEFAULT_CONSOLE_LOGLEVEL=8 +## At a maximum only compile in this level of debugging +default MAXIMUM_CONSOLE_LOGLEVEL=8 + +## +## Select power on after power fail setting +default MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON" + +### End Options.lb +end |