diff options
Diffstat (limited to 'src/mainboard/google')
| -rw-r--r-- | src/mainboard/google/poppy/Kconfig | 28 | ||||
| -rw-r--r-- | src/mainboard/google/poppy/variants/baseboard/devicetree.cb | 8 | ||||
| -rw-r--r-- | src/mainboard/google/poppy/variants/baseboard/gpio.c | 22 |
3 files changed, 50 insertions, 8 deletions
diff --git a/src/mainboard/google/poppy/Kconfig b/src/mainboard/google/poppy/Kconfig index ce320813c0..58af8df4dd 100644 --- a/src/mainboard/google/poppy/Kconfig +++ b/src/mainboard/google/poppy/Kconfig @@ -22,7 +22,16 @@ config DEVICETREE string default "variants/baseboard/devicetree.cb" +config DRIVER_TPM_I2C_BUS + depends on POPPY_USE_I2C_TPM + default 0x4 + +config DRIVER_TPM_I2C_ADDR + depends on POPPY_USE_I2C_TPM + default 0x50 + config DRIVER_TPM_SPI_BUS + depends on POPPY_USE_SPI_TPM default 0x1 config GBB_HWID @@ -56,6 +65,14 @@ config MAX_CPUS int default 8 +# Select this option to enable use of cr50 I2C TPM on poppy. +config POPPY_USE_I2C_TPM + bool + default n + select I2C_TPM + select MAINBOARD_HAS_I2C_TPM_CR50 + select TPM2 + # Select this option to enable use of cr50 SPI TPM on poppy. # This option is disabled by default. config POPPY_USE_SPI_TPM @@ -65,6 +82,10 @@ config POPPY_USE_SPI_TPM select SPI_TPM select TPM2 +config TPM_TIS_ACPI_INTERRUPT + int + default 64 # GPE0_DW2_00 (GPP_E0) + config VARIANT_DIR string default "poppy" if BOARD_GOOGLE_POPPY @@ -76,11 +97,4 @@ config VBOOT select MRC_CLEAR_NORMAL_CACHE_ON_RECOVERY_RETRAIN select VBOOT_LID_SWITCH -config DRIVER_TPM_SPI_BUS - default 0x1 - -config TPM_TIS_ACPI_INTERRUPT - int - default 64 # GPE0_DW2_00 (GPP_E0) - endif # BOARD_GOOGLE_BASEBOARD_POPPY diff --git a/src/mainboard/google/poppy/variants/baseboard/devicetree.cb b/src/mainboard/google/poppy/variants/baseboard/devicetree.cb index d232028544..4e3ffaf68c 100644 --- a/src/mainboard/google/poppy/variants/baseboard/devicetree.cb +++ b/src/mainboard/google/poppy/variants/baseboard/devicetree.cb @@ -154,7 +154,7 @@ chip soc/intel/skylake register "usb3_ports[3]" = "USB3_PORT_EMPTY" # Empty register "i2c_voltage[0]" = "I2C_VOLTAGE_3V3" # Touchscreen - register "i2c_voltage[1]" = "I2C_VOLTAGE_3V3" # NFC + register "i2c_voltage[1]" = "I2C_VOLTAGE_3V3" # H1 register "i2c_voltage[2]" = "I2C_VOLTAGE_1V8" # Camera register "i2c_voltage[3]" = "I2C_VOLTAGE_1V8" # Pen register "i2c_voltage[4]" = "I2C_VOLTAGE_1V8" # Camera @@ -167,6 +167,12 @@ chip soc/intel/skylake .early_init = 1, }" + # Configure I2C1 for cr50 TPM. Early init is required to set up a BAR + # for TPM communication before memory is up. + register "i2c[1]" = "{ + .early_init = 1, + }" + # Must leave UART0 enabled or SD/eMMC will not work as PCI register "SerialIoDevMode" = "{ [PchSerialIoIndexI2C0] = PchSerialIoPci, diff --git a/src/mainboard/google/poppy/variants/baseboard/gpio.c b/src/mainboard/google/poppy/variants/baseboard/gpio.c index fcbbb1d554..2be9d0f86f 100644 --- a/src/mainboard/google/poppy/variants/baseboard/gpio.c +++ b/src/mainboard/google/poppy/variants/baseboard/gpio.c @@ -92,6 +92,7 @@ static const struct pad_config gpio_table[] = { PAD_CFG_NF(GPP_B13, NONE, DEEP, NF1), /* B14 : SPKR ==> NC */ PAD_CFG_NC(GPP_B14), +#if IS_ENABLED(CONFIG_POPPY_USE_SPI_TPM) /* B15 : GSPI0_CS# ==> PCH_SPI_H1_3V3_CS_L */ PAD_CFG_NF(GPP_B15, NONE, DEEP, NF1), /* B16 : GSPI0_CLK ==> PCH_SPI_H1_3V3_CLK */ @@ -100,6 +101,16 @@ static const struct pad_config gpio_table[] = { PAD_CFG_NF(GPP_B17, NONE, DEEP, NF1), /* B18 : GSPI0_MOSI ==> PCH_SPI_H1_3V3_MOSI */ PAD_CFG_NF(GPP_B18, NONE, DEEP, NF1), +#else + /* B15 : GSPI0_CS# ==> NC */ + PAD_CFG_NC(GPP_B15), + /* B16 : GSPI0_CLK ==> NC */ + PAD_CFG_NC(GPP_B16), + /* B17 : GSPI0_MISO ==> NC */ + PAD_CFG_NC(GPP_B17), + /* B18 : GSPI0_MOSI ==> NC */ + PAD_CFG_NC(GPP_B18), +#endif /* B19 : GSPI1_CS# ==> PCH_SPI_FP_CS_L */ PAD_CFG_NF(GPP_B19, NONE, DEEP, NF1), /* B20 : GSPI1_CLK ==> PCH_SPI_FP_CLK */ @@ -147,10 +158,17 @@ static const struct pad_config gpio_table[] = { PAD_CFG_NF(GPP_C16, NONE, DEEP, NF1), /* C17 : I2C0_SCL ==> PCH_I2C0_TOUCHSCREEN_3V3_SCL */ PAD_CFG_NF(GPP_C17, NONE, DEEP, NF1), +#if IS_ENABLED(CONFIG_POPPY_USE_I2C_TPM) /* C18 : I2C1_SDA ==> PCH_I2C1_H1_3V3_SDA */ PAD_CFG_NF(GPP_C18, NONE, DEEP, NF1), /* C19 : I2C1_SCL ==> PCH_I2C1_H1_3V3_SCL */ PAD_CFG_NF(GPP_C19, NONE, DEEP, NF1), +#else + /* C18 : I2C1_SDA ==> NC */ + PAD_CFG_NC(GPP_C18), + /* C19 : I2C1_SCL ==> NC */ + PAD_CFG_NC(GPP_C19), +#endif /* C20 : UART2_RXD ==> PCHRX_SERVOTX_UART */ PAD_CFG_NF(GPP_C20, NONE, DEEP, NF1), /* C21 : UART2_TXD ==> PCHTX_SERVORX_UART */ @@ -353,6 +371,7 @@ static const struct pad_config gpio_table[] = { /* Early pad configuration in bootblock */ static const struct pad_config early_gpio_table[] = { +#if IS_ENABLED(CONFIG_POPPY_USE_SPI_TPM) /* B15 : GSPI0_CS# ==> PCH_SPI_H1_3V3_CS_L */ PAD_CFG_NF(GPP_B15, NONE, DEEP, NF1), /* B16 : GSPI0_CLK ==> PCH_SPI_H1_3V3_CLK */ @@ -361,11 +380,14 @@ static const struct pad_config early_gpio_table[] = { PAD_CFG_NF(GPP_B17, NONE, DEEP, NF1), /* B18 : GSPI0_MOSI ==> PCH_SPI_H1_3V3_MOSI */ PAD_CFG_NF(GPP_B18, NONE, DEEP, NF1), +#endif +#if IS_ENABLED(CONFIG_POPPY_USE_I2C_TPM) /* C18 : I2C1_SDA ==> PCH_I2C1_H1_3V3_SDA */ PAD_CFG_NF(GPP_C18, NONE, DEEP, NF1), /* C19 : I2C1_SCL ==> PCH_I2C1_H1_3V3_SCL */ PAD_CFG_NF(GPP_C19, NONE, DEEP, NF1), +#endif /* Ensure UART pins are in native mode for H1. */ /* C20 : UART2_RXD ==> PCHRX_SERVOTX_UART */ |