diff options
Diffstat (limited to 'src/mainboard/google')
| -rw-r--r-- | src/mainboard/google/volteer/variants/collis/overridetree.cb | 251 |
1 files changed, 250 insertions, 1 deletions
diff --git a/src/mainboard/google/volteer/variants/collis/overridetree.cb b/src/mainboard/google/volteer/variants/collis/overridetree.cb index 32204c58e7..fda59e563d 100644 --- a/src/mainboard/google/volteer/variants/collis/overridetree.cb +++ b/src/mainboard/google/volteer/variants/collis/overridetree.cb @@ -1,6 +1,255 @@ chip soc/intel/tigerlake + # BitMask where bits [3:0] are Controller 0 Channel [3:0] and + # bits [7:4] are Controller 1 Channel [3:0]. + # Enable Command Mirroring for controller 0 channel 0 and 1, + # and controller 1 channel 0 and 1. + register "CmdMirror" = "0x00000033" + + register "DdiPort1Hpd" = "0" + register "DdiPort2Hpd" = "0" + + register "usb2_ports[0]" = "USB2_PORT_TYPE_C(OC1)" # Type-A Port A0 + register "usb2_ports[1]" = "USB2_PORT_TYPE_C(OC2)" # Type-A Port A1 + register "usb2_ports[2]" = "USB2_PORT_TYPE_C(OC0)" # Type-C Port C1 + register "usb2_ports[3]" = "USB2_PORT_MID(OC_SKIP)" # Front Camera + register "usb2_ports[4]" = "USB2_PORT_TYPE_C(OC3)" # Type-C Port C0 + register "usb2_ports[5]" = "USB2_PORT_MID(OC_SKIP)" # WFC Camera + register "usb3_ports[0]" = "USB3_PORT_DEFAULT(OC1)" # USB3/2 Type-A Port A0 + register "usb3_ports[1]" = "USB3_PORT_DEFAULT(OC2)" # USB3/2 Type-A Port A1 + + # Disable SRCCLKREQ1# + register "PcieClkSrcUsage[1]" = "PCIE_CLK_NOTUSED" + + #+-------------------+---------------------------+ + #| Field | Value | + #+-------------------+---------------------------+ + #| chipset_lockdown | CHIPSET_LOCKDOWN_COREBOOT | + #| GSPI0 | cr50 TPM. Early init is | + #| | required to set up a BAR | + #| | for TPM communication | + #| | before memory is up | + #| I2C0 | Audio | + #| I2C1 | Touchscreen | + #| I2C5 | Trackpad | + #+-------------------+---------------------------+ + register "common_soc_config" = "{ + .chipset_lockdown = CHIPSET_LOCKDOWN_COREBOOT, + .gspi[0] = { + .speed_mhz = 1, + .early_init = 1, + }, + .i2c[0] = { + .speed = I2C_SPEED_FAST, + }, + .i2c[1] = { + .speed = I2C_SPEED_FAST, + }, + .i2c[5] = { + .speed = I2C_SPEED_FAST, + }, + }" device domain 0 on + device ref i2c0 on + chip drivers/i2c/generic + register "hid" = ""10EC5682"" + register "name" = ""RT58"" + register "desc" = ""Headset Codec"" + register "irq_gpio" = "ACPI_GPIO_IRQ_EDGE_BOTH(GPP_R5)" + # Set the jd_src to RT5668_JD1 for jack detection + register "property_count" = "1" + register "property_list[0].type" = "ACPI_DP_TYPE_INTEGER" + register "property_list[0].name" = ""realtek,jd-src"" + register "property_list[0].integer" = "1" + device i2c 1a on + end + end + chip drivers/i2c/max98373 + register "vmon_slot_no" = "0" + register "imon_slot_no" = "1" + register "uid" = "0" + register "desc" = ""Right Speaker Amp"" + register "name" = ""MAXR"" + device i2c 31 on + probe AUDIO MAX98373_ALC5682I_I2S_UP4 + end + end + chip drivers/i2c/max98373 + register "vmon_slot_no" = "2" + register "imon_slot_no" = "3" + register "uid" = "1" + register "desc" = ""Left Speaker Amp"" + register "name" = ""MAXL"" + device i2c 32 on + probe AUDIO MAX98373_ALC5682I_I2S_UP4 + end + end + end + device ref i2c1 on + chip drivers/i2c/hid + register "generic.hid" = ""ELAN9008"" + register "generic.desc" = ""ELAN Touchscreen"" + register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPP_E7_IRQ)" + register "generic.probed" = "1" + register "generic.reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C10)" + register "generic.enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_F16)" + register "generic.reset_delay_ms" = "20" + register "generic.has_power_resource" = "1" + register "generic.disable_gpio_export_in_crs" = "1" + register "hid_desc_reg_offset" = "0x01" + device i2c 10 on end + end + chip drivers/generic/gpio_keys + register "name" = ""PENH"" + # GPP_E17 is the IRQ source, and GPP_E1 is the wake source + register "gpio" = "ACPI_GPIO_INPUT_ACTIVE_LOW(GPP_E17)" + register "key.wake_gpe" = "GPE0_DW2_01" + register "key.wakeup_route" = "WAKEUP_ROUTE_SCI" + register "key.wakeup_event_action" = "EV_ACT_DEASSERTED" + register "key.dev_name" = ""EJCT"" + register "key.linux_code" = "SW_PEN_INSERTED" + register "key.linux_input_type" = "EV_SW" + register "key.label" = ""pen_eject"" + device generic 0 on end + end + end + device ref i2c5 on + chip drivers/i2c/generic + register "hid" = ""ELAN0000"" + register "desc" = ""ELAN Touchpad"" + register "irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_E15_IRQ)" + register "wake" = "GPE0_DW2_15" + register "probed" = "1" + device i2c 15 on + probe TOUCHPAD REGULAR_TOUCHPAD + end + end + chip drivers/i2c/hid + register "generic.hid" = ""ELAN2702"" + register "generic.desc" = ""ELAN Touchpad"" + register "generic.irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_E15_IRQ)" + register "generic.wake" = "GPE0_DW2_15" + register "generic.probed" = "1" + register "hid_desc_reg_offset" = "0x01" + device i2c 15 on + probe TOUCHPAD NUMPAD_TOUCHPAD + end + end + end + device ref pch_espi on + chip ec/google/chromeec + use conn0 as mux_conn[0] + use conn1 as mux_conn[1] + device pnp 0c09.0 on end + end + end + device ref pcie_rp9 on + chip soc/intel/common/block/pcie/rtd3 + register "enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_B2)" + register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_A11)" + register "srcclk_pin" = "0" + device generic 0 on end + end + end + device ref pmc hidden + # The pmc_mux chip driver is a placeholder for the + # PMC.MUX device in the ACPI hierarchy. + chip drivers/intel/pmc_mux + device generic 0 on + chip drivers/intel/pmc_mux/conn + register "usb2_port_number" = "5" + register "usb3_port_number" = "1" + # SBU is fixed, HSL follows CC + register "sbu_orientation" = "TYPEC_ORIENTATION_NORMAL" + device generic 0 alias conn0 on end + end + chip drivers/intel/pmc_mux/conn + register "usb2_port_number" = "3" + register "usb3_port_number" = "2" + # SBU is fixed, HSL follows CC + register "sbu_orientation" = "TYPEC_ORIENTATION_NORMAL" + device generic 1 alias conn1 on end + end + end + end + end + device ref north_xhci on + chip drivers/usb/acpi + device ref tcss_root_hub on + chip drivers/usb/acpi + register "desc" = ""USB3 Type-C Port C0 (MLB)"" + register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" + register "group" = "ACPI_PLD_GROUP(4, 2)" + device ref tcss_usb3_port1 on end + end + chip drivers/usb/acpi + register "desc" = ""USB3 Type-C Port C1 (DB)"" + register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" + register "group" = "ACPI_PLD_GROUP(3, 2)" + device ref tcss_usb3_port2 on + probe DB_USB USB3_ACTIVE + end + end + end + end + end + device ref south_xhci on + chip drivers/usb/acpi + device ref xhci_root_hub on + chip drivers/usb/acpi + register "desc" = ""USB2 Type-A Port A0 (MLB)"" + register "type" = "UPC_TYPE_A" + register "group" = "ACPI_PLD_GROUP(1, 1)" + device ref usb2_port1 on end + end + chip drivers/usb/acpi + register "desc" = ""USB2 Type-A Port A1 (DB)"" + register "type" = "UPC_TYPE_A" + register "group" = "ACPI_PLD_GROUP(2, 1)" + device ref usb2_port2 on + probe DB_USB USB3_ACTIVE + end + end + chip drivers/usb/acpi + register "desc" = ""USB2 Type-C Port C1 (DB)"" + register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" + register "group" = "ACPI_PLD_GROUP(3, 1)" + device ref usb2_port3 on + probe DB_USB USB3_ACTIVE + end + end + chip drivers/usb/acpi + register "desc" = ""USB2 Camera"" + register "type" = "UPC_TYPE_INTERNAL" + device ref usb2_port4 on end + end + chip drivers/usb/acpi + register "desc" = ""USB2 Type-C Port C0 (MLB)"" + register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" + register "group" = "ACPI_PLD_GROUP(4, 1)" + device ref usb2_port5 on end + end + chip drivers/usb/acpi + register "desc" = ""WFC Camera"" + register "type" = "UPC_TYPE_INTERNAL" + device ref usb2_port6 on end + end + chip drivers/usb/acpi + register "desc" = ""USB3 Type-A Port A0 (MLB)"" + register "type" = "UPC_TYPE_USB3_A" + register "group" = "ACPI_PLD_GROUP(1, 2)" + device ref usb3_port1 on end + end + chip drivers/usb/acpi + register "desc" = ""USB3 Type-A Port A1 (DB)"" + register "type" = "UPC_TYPE_USB3_A" + register "group" = "ACPI_PLD_GROUP(2, 2)" + device ref usb3_port2 on + probe DB_USB USB3_ACTIVE + end + end + end + end + end end - end |