diff options
Diffstat (limited to 'src/mainboard/google/zork/variants/baseboard/devicetree.cb')
| -rw-r--r-- | src/mainboard/google/zork/variants/baseboard/devicetree.cb | 189 |
1 files changed, 189 insertions, 0 deletions
diff --git a/src/mainboard/google/zork/variants/baseboard/devicetree.cb b/src/mainboard/google/zork/variants/baseboard/devicetree.cb new file mode 100644 index 0000000000..c90c3225a3 --- /dev/null +++ b/src/mainboard/google/zork/variants/baseboard/devicetree.cb @@ -0,0 +1,189 @@ +# SPDX-License-Identifier: GPL-2.0-or-later +chip soc/amd/picasso + + # Set FADT Configuration + register "fadt_pm_profile" = "PM_MOBILE" + register "fadt_boot_arch" = "ACPI_FADT_LEGACY_DEVICES | ACPI_FADT_8042" + register "fadt_flags" = "ACPI_FADT_WBINVD | /* See table 5-34 ACPI 6.3 spec */ + ACPI_FADT_C1_SUPPORTED | + ACPI_FADT_SLEEP_BUTTON | + ACPI_FADT_S4_RTC_WAKE | + ACPI_FADT_32BIT_TIMER | + ACPI_FADT_RESET_REGISTER | + ACPI_FADT_SEALED_CASE | + ACPI_FADT_PCI_EXPRESS_WAKE | + ACPI_FADT_REMOTE_POWER_ON" + + register "acp_pin_cfg" = "I2S_PINS_I2S_TDM" + + # Start : OPN Performance Configuration + # (Configuratin that is common for all variants) + # For the below fields, 0 indicates use SOC default + + # PROCHOT_L de-assertion Ramp Time + register "prochot_l_deassertion_ramp_time" = "20" #mS + + # Lower die temperature limit + register "thermctl_limit" = "100" #degrees C + + # FP5 Processor Voltage Supply PSI Currents + register "psi0_current_limit" = "18000" #mA + register "psi0_soc_current_limit" = "12000" #mA + register "vddcr_soc_voltage_margin" = "0" #mV + register "vddcr_vdd_voltage_margin" = "0" #mV + + # VRM Limits + register "vrm_maximum_current_limit" = "0" #mA + register "vrm_soc_maximum_current_limit" = "0" #mA + register "vrm_current_limit" = "0" #mA + register "vrm_soc_current_limit" = "0" #mA + + # Misc SMU settings + register "sb_tsi_alert_comparator_mode_en" = "0" + register "core_dldo_bypass" = "1" + register "min_soc_vid_offset" = "0" + register "aclk_dpm0_freq_400MHz" = "0" + + # End : OPN Performance Configuration + + register "sd_emmc_config" = "SD_EMMC_EMMC_HS400" + + # SPI Configuration + register "common_config.spi_config" = "{ + .normal_speed = SPI_SPEED_66M, /* MHz */ + .fast_speed = SPI_SPEED_66M, /* MHz */ + .altio_speed = SPI_SPEED_66M, /* MHz */ + .tpm_speed = SPI_SPEED_66M, /* MHz */ + .read_mode = SPI_READ_MODE_DUAL112, + }" + + # eSPI Configuration + register "common_config.espi_config" = "{ + .std_io_decode_bitmap = ESPI_DECODE_IO_0x80_EN | ESPI_DECODE_IO_0X60_0X64_EN, + .generic_io_range[0] = { + .base = 0x62, + /* + * Only 0x62 and 0x66 are required. But, this is not supported by + * standard IO decodes and there are only 4 generic I/O windows + * available. Hence, open a window from 0x62-0x67. + */ + .size = 5, + }, + .generic_io_range[1] = { + .base = 0x800, /* EC_HOST_CMD_REGION0 */ + .size = 256, /* EC_HOST_CMD_REGION_SIZE * 2 */ + }, + .generic_io_range[2] = { + .base = 0x900, /* EC_LPC_ADDR_MEMMAP */ + .size = 255, /* EC_MEMMAP_SIZE */ + }, + .generic_io_range[3] = { + .base = 0x200, /* EC_LPC_ADDR_HOST_DATA */ + .size = 8, /* 0x200 - 0x207 */ + }, + + .io_mode = ESPI_IO_MODE_QUAD, + .op_freq_mhz = ESPI_OP_FREQ_33_MHZ, + .crc_check_enable = 1, + .dedicated_alert_pin = 1, + .periph_ch_en = 1, + .vw_ch_en = 1, + .oob_ch_en = 0, + .flash_ch_en = 0, + + .vw_irq_polarity = ESPI_VW_IRQ_LEVEL_LOW(1) | ESPI_VW_IRQ_LEVEL_LOW(12), + }" + + register "i2c_scl_reset" = "GPIO_I2C2_SCL | GPIO_I2C3_SCL" + + register "irq_override" = "{ + /* PS/2 keyboard IRQ1 override */ + {1, MP_IRQ_TRIGGER_LEVEL | MP_IRQ_POLARITY_HIGH}, + + /* PS/2 mouse IRQ12 override */ + {12, MP_IRQ_TRIGGER_LEVEL | MP_IRQ_POLARITY_HIGH}, + }" + + device cpu_cluster 0 on + device lapic 0 on end + end + + # See AMD 55570-B1 Table 13: PCI Device ID Assignments. + device domain 0 on + subsystemid 0x1022 0x1510 inherit + device pci 0.0 on end # Root Complex + device pci 0.2 on end # IOMMU + device pci 1.0 on end # Dummy Host Bridge, must be enabled + device pci 1.1 off end # GPP Bridge 0 + device pci 1.2 on end # GPP Bridge 1 - Wifi + device pci 1.3 on end # GPP Bridge 2 - SD + device pci 1.4 off end # GPP Bridge 3 + device pci 1.5 off end # GPP Bridge 4 + device pci 8.0 on end # Dummy Host Bridge, must be enabled + device pci 8.1 on # Internal GPP Bridge 0 to Bus A + device pci 0.0 on end # Internal GPU + device pci 0.1 on end # Display HDA + device pci 0.2 on end # Crypto Coprocesor + device pci 0.5 on end # Audio + device pci 0.6 on end # HDA + device pci 0.7 on end # non-Sensor Fusion Hub device + end + device pci 8.2 on # Internal GPP Bridge 0 to Bus B + device pci 0.0 on end # AHCI + end + device pci 14.0 on end # SM + device pci 14.3 on # - D14F3 bridge + chip ec/google/chromeec + device pnp 0c09.0 on + chip ec/google/chromeec/i2c_tunnel + register "uid" = "1" + register "remote_bus" = "8" + device generic 0.0 on + chip drivers/i2c/generic + register "hid" = ""10EC5682"" + register "name" = ""RT58"" + register "uid" = "1" + register "desc" = ""Realtek RT5682"" + register "irq_gpio" = "ACPI_GPIO_IRQ_EDGE_BOTH(62)" + register "property_count" = "1" + register "property_list[0].type" = "ACPI_DP_TYPE_INTEGER" + register "property_list[0].name" = ""realtek,jd-src"" + register "property_list[0].integer" = "1" + device i2c 1a on end + end + end + end + chip ec/google/chromeec/i2c_tunnel + register "name" = ""MSTH"" + register "uid" = "1" + register "remote_bus" = "9" + device generic 1.0 on end + end + end + end + end + device pci 18.0 on end # Data fabric [0-7] + device pci 18.1 on end + device pci 18.2 on end + device pci 18.3 on end + device pci 18.4 on end + device pci 18.5 on end + device pci 18.6 on end + end # domain + + chip drivers/generic/max98357a + register "sdmode_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPIO_91)" + register "sdmode_delay" = "5" + device generic 0.1 on end + end + + device mmio 0xfedc5000 on + chip drivers/i2c/tpm + register "hid" = ""GOOG0005"" + register "desc" = ""Cr50 TPM"" + register "irq_gpio" = "ACPI_GPIO_IRQ_EDGE_LOW(GPIO_3)" + device i2c 50 on end + end + end + +end # chip soc/amd/picasso |