diff options
Diffstat (limited to 'src/mainboard/google/brya/variants')
| -rw-r--r-- | src/mainboard/google/brya/variants/glassway/overridetree.cb | 494 |
1 files changed, 492 insertions, 2 deletions
diff --git a/src/mainboard/google/brya/variants/glassway/overridetree.cb b/src/mainboard/google/brya/variants/glassway/overridetree.cb index 4f2c04a57a..ddeff20e51 100644 --- a/src/mainboard/google/brya/variants/glassway/overridetree.cb +++ b/src/mainboard/google/brya/variants/glassway/overridetree.cb @@ -1,6 +1,496 @@ +fw_config + field THERMAL_SOLUTION 0 + option THERMAL_SOLUTION_PASSIVE 0 + option THERMAL_SOLUTION_ACTIVE 1 + end + field DB_USB 5 7 + option DB_NONE 0 + option DB_1C 1 + option DB_1A 2 + option DB_1C_1A 3 + end + field SD_CARD 8 + option SD_ABSENT 0 + option SD_GL9750S 1 + end + field TOUCHSCREEN_SOURCE 32 33 + option TOUCHSCREEN_UNPROVISIONED 0 + option TOUCHSCREEN_ELAN0001 1 + option TOUCHSCREEN_ELAN9008 2 + end +end + chip soc/intel/alderlake + register "sagv" = "SaGv_Enabled" + + # SOC Aux orientation override: + # This is a bitfield that corresponds to up to 4 TCSS ports. + # Bits (0,1) allocated for TCSS Port1 configuration and Bits (2,3)for TCSS Port2. + # TcssAuxOri = 0101b + # Bit0,Bit2 set to "1" indicates no retimer on USBC Ports + # Bit1,Bit3 set to "0" indicates Aux lines are not swapped on the + # motherboard to USBC connector + register "tcss_aux_ori" = "5" + + register "typec_aux_bias_pads[0]" = "{.pad_auxp_dc = GPP_E22, .pad_auxn_dc = GPP_E23}" + register "typec_aux_bias_pads[1]" = "{.pad_auxp_dc = GPP_A21, .pad_auxn_dc = GPP_A22}" + + register "usb2_ports[9]" = "USB2_PORT_MID(OC_SKIP)" # Bluetooth port for CNVi WLAN + + # Configure external V1P05/Vnn/VnnSx Rails + register "ext_fivr_settings" = "{ + .configure_ext_fivr = 1, + .v1p05_enable_bitmap = FIVR_ENABLE_ALL_SX & ~FIVR_ENABLE_S0, + .vnn_enable_bitmap = FIVR_ENABLE_ALL_SX, + .vnn_sx_enable_bitmap = FIVR_ENABLE_ALL_SX, + .v1p05_supported_voltage_bitmap = FIVR_VOLTAGE_NORMAL, + .vnn_supported_voltage_bitmap = FIVR_VOLTAGE_MIN_ACTIVE, + .v1p05_voltage_mv = 1050, + .vnn_voltage_mv = 780, + .vnn_sx_voltage_mv = 1050, + .v1p05_icc_max_ma = 500, + .vnn_icc_max_ma = 500, + }" + + # Enable the Cnvi BT Audio Offload + register "cnvi_bt_audio_offload" = "1" + + # Intel Common SoC Config + #+-------------------+---------------------------+ + #| Field | Value | + #+-------------------+---------------------------+ + #| I2C0 | TPM. Early init is | + #| | required to set up a BAR | + #| | for TPM communication | + #| I2C1 | Touchscreen | + #| I2C2 | Sub-board(PSensor)/WCAM | + #| I2C3 | Audio | + #| I2C5 | Trackpad | + #+-------------------+---------------------------+ + register "common_soc_config" = "{ + .i2c[0] = { + .early_init = 1, + .speed = I2C_SPEED_FAST_PLUS, + .speed_config[0] = { + .speed = I2C_SPEED_FAST_PLUS, + .scl_lcnt = 55, + .scl_hcnt = 30, + .sda_hold = 7, + } + }, + .i2c[1] = { + .speed = I2C_SPEED_FAST, + .speed_config[0] = { + .speed = I2C_SPEED_FAST, + .scl_lcnt = 157, + .scl_hcnt = 79, + .sda_hold = 7, + } + }, + .i2c[2] = { + .speed = I2C_SPEED_FAST, + .speed_config[0] = { + .speed = I2C_SPEED_FAST, + .scl_lcnt = 157, + .scl_hcnt = 79, + .sda_hold = 7, + } + }, + .i2c[3] = { + .speed = I2C_SPEED_FAST, + .speed_config[0] = { + .speed = I2C_SPEED_FAST, + .scl_lcnt = 158, + .scl_hcnt = 79, + .sda_hold = 7, + } + }, + .i2c[5] = { + .speed = I2C_SPEED_FAST, + .speed_config[0] = { + .speed = I2C_SPEED_FAST, + .scl_lcnt = 158, + .scl_hcnt = 79, + .sda_hold = 7, + } + }, + }" + + device domain 0 on + device ref dtt on + chip drivers/intel/dptf + ## sensor information + register "options.tsr[0].desc" = ""Memory"" + register "options.tsr[1].desc" = ""Charger"" + register "options.tsr[2].desc" = ""Ambient"" + + # TODO: below values are initial reference values only + ## Passive Policy + register "policies.passive" = "{ + [0] = DPTF_PASSIVE(CPU, CPU, 95, 5000), + [1] = DPTF_PASSIVE(CPU, TEMP_SENSOR_0, 75, 5000), + [2] = DPTF_PASSIVE(CHARGER, TEMP_SENSOR_1, 75, 5000), + [3] = DPTF_PASSIVE(CPU, TEMP_SENSOR_2, 75, 5000), + }" + + ## Critical Policy + register "policies.critical" = "{ + [0] = DPTF_CRITICAL(CPU, 105, SHUTDOWN), + [1] = DPTF_CRITICAL(TEMP_SENSOR_0, 85, SHUTDOWN), + [2] = DPTF_CRITICAL(TEMP_SENSOR_1, 85, SHUTDOWN), + [3] = DPTF_CRITICAL(TEMP_SENSOR_2, 85, SHUTDOWN), + }" + + register "controls.power_limits" = "{ + .pl1 = { + .min_power = 3000, + .max_power = 6000, + .time_window_min = 28 * MSECS_PER_SEC, + .time_window_max = 32 * MSECS_PER_SEC, + .granularity = 200 + }, + .pl2 = { + .min_power = 25000, + .max_power = 25000, + .time_window_min = 1, + .time_window_max = 1, + .granularity = 1000 + } + }" + + ## Charger Performance Control (Control, mA) + register "controls.charger_perf" = "{ + [0] = { 255, 1700 }, + [1] = { 24, 1500 }, + [2] = { 16, 1000 }, + [3] = { 8, 500 } + }" + + device generic 0 on + probe THERMAL_SOLUTION THERMAL_SOLUTION_PASSIVE + end + end + chip drivers/intel/dptf + ## sensor information + register "options.tsr[0].desc" = ""Memory"" + register "options.tsr[1].desc" = ""Charger"" + register "options.tsr[2].desc" = ""Ambient"" + + # TODO: below values are initial reference values only + ## Active Policy + register "policies.active" = "{ + [0] = { + .target = DPTF_CPU, + .thresholds = { + TEMP_PCT(85, 90), + TEMP_PCT(80, 80), + TEMP_PCT(75, 70), + TEMP_PCT(70, 50), + TEMP_PCT(65, 30), + } + }, + [1] = { + .target = DPTF_TEMP_SENSOR_2, + .thresholds = { + TEMP_PCT(50, 90), + TEMP_PCT(48, 70), + TEMP_PCT(46, 60), + TEMP_PCT(43, 40), + TEMP_PCT(40, 30), + } + } + }" + + # TODO: below values are initial reference values only + ## Passive Policy + register "policies.passive" = "{ + [0] = DPTF_PASSIVE(CPU, CPU, 95, 5000), + [1] = DPTF_PASSIVE(CPU, TEMP_SENSOR_0, 75, 5000), + [2] = DPTF_PASSIVE(CHARGER, TEMP_SENSOR_1, 75, 5000), + [3] = DPTF_PASSIVE(CPU, TEMP_SENSOR_2, 75, 5000), + }" + + ## Critical Policy + register "policies.critical" = "{ + [0] = DPTF_CRITICAL(CPU, 105, SHUTDOWN), + [1] = DPTF_CRITICAL(TEMP_SENSOR_0, 85, SHUTDOWN), + [2] = DPTF_CRITICAL(TEMP_SENSOR_1, 85, SHUTDOWN), + [3] = DPTF_CRITICAL(TEMP_SENSOR_2, 85, SHUTDOWN), + }" + + register "controls.power_limits" = "{ + .pl1 = { + .min_power = 12000, + .max_power = 15000, + .time_window_min = 28 * MSECS_PER_SEC, + .time_window_max = 32 * MSECS_PER_SEC, + .granularity = 200 + }, + .pl2 = { + .min_power = 35000, + .max_power = 35000, + .time_window_min = 1, + .time_window_max = 1, + .granularity = 1000 + } + }" + + ## Charger Performance Control (Control, mA) + register "controls.charger_perf" = "{ + [0] = { 255, 1700 }, + [1] = { 24, 1500 }, + [2] = { 16, 1000 }, + [3] = { 8, 500 } + }" + + ## Fan Performance Control (Percent, Speed, Noise, Power) + register "controls.fan_perf" = "{ + [0] = { 100, 6000, 220, 2200, }, + [1] = { 92, 5500, 180, 1800, }, + [2] = { 85, 5000, 145, 1450, }, + [3] = { 70, 4400, 115, 1150, }, + [4] = { 56, 3900, 90, 900, }, + [5] = { 45, 3300, 55, 550, }, + [6] = { 38, 3000, 30, 300, }, + [7] = { 33, 2900, 15, 150, }, + [8] = { 10, 800, 10, 100, }, + [9] = { 0, 0, 0, 50, } + }" - device domain 0 on - end + ## Fan options + register "options.fan.fine_grained_control" = "1" + register "options.fan.step_size" = "2" + device generic 1 on + probe THERMAL_SOLUTION THERMAL_SOLUTION_ACTIVE + end + end + end + device ref cnvi_wifi on + chip drivers/wifi/generic + register "enable_cnvi_ddr_rfim" = "true" + device generic 0 on end + end + end + device ref i2c1 on + chip drivers/i2c/generic + register "hid" = ""ELAN0001"" + register "desc" = ""ELAN Touchscreen"" + register "irq" = "ACPI_IRQ_LEVEL_LOW(GPP_C7_IRQ)" + register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C1)" + register "reset_delay_ms" = "25" + register "reset_off_delay_ms" = "4" + register "stop_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C6)" + register "stop_delay_ms" = "25" + register "stop_off_delay_ms" = "2" + register "enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_C0)" + register "enable_delay_ms" = "7" + register "has_power_resource" = "1" + device i2c 10 on + probe TOUCHSCREEN_SOURCE TOUCHSCREEN_UNPROVISIONED + probe TOUCHSCREEN_SOURCE TOUCHSCREEN_ELAN0001 + end + end + chip drivers/i2c/hid + register "generic.hid" = ""ELAN9008"" + register "generic.desc" = ""ELAN Touchscreen"" + register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPP_C7_IRQ)" + register "generic.detect" = "1" + register "generic.reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C1)" + register "generic.reset_delay_ms" = "20" + register "generic.reset_off_delay_ms" = "2" + register "generic.stop_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C6)" + register "generic.stop_delay_ms" = "280" + register "generic.stop_off_delay_ms" = "2" + register "generic.enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_C0)" + register "generic.enable_delay_ms" = "1" + register "generic.has_power_resource" = "1" + register "hid_desc_reg_offset" = "0x01" + device i2c 10 on + probe TOUCHSCREEN_SOURCE TOUCHSCREEN_ELAN9008 + end + end + end #I2C1 + device ref i2c3 on + chip drivers/i2c/generic + register "hid" = ""RTL5682"" + register "name" = ""RT58"" + register "desc" = ""Headset Codec"" + register "irq_gpio" = "ACPI_GPIO_IRQ_EDGE_BOTH(GPP_A23)" + # Set the jd_src to RT5668_JD1 for jack detection + register "property_count" = "1" + register "property_list[0].type" = "ACPI_DP_TYPE_INTEGER" + register "property_list[0].name" = ""realtek,jd-src"" + register "property_list[0].integer" = "1" + device i2c 1a on end + end + chip drivers/generic/alc1015 + register "hid" = ""RTL1019"" + register "sdb" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_A11)" + device generic 1 on end + end + end #I2C3 + device ref i2c5 on + chip drivers/i2c/generic + register "hid" = ""ELAN0000"" + register "desc" = ""ELAN Touchpad"" + register "irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_F14_IRQ)" + register "wake" = "GPE0_DW2_14" + register "detect" = "1" + device i2c 15 on end + end + end #I2C5 + device ref pcie_rp4 on + # Enable wlan PCIe 4 using clk 2 + register "pch_pcie_rp[PCH_RP(4)]" = "{ + .clk_src = 2, + .clk_req = 2, + .flags = PCIE_RP_LTR | PCIE_RP_AER, + }" + chip drivers/wifi/generic + register "add_acpi_dma_property" = "true" + device pci 00.0 on end + end + end + device ref pcie_rp7 on + # Enable SD Card PCIe 7 using clk 3 + register "pch_pcie_rp[PCH_RP(7)]" = "{ + .clk_src = 3, + .clk_req = 3, + .flags = PCIE_RP_HOTPLUG | PCIE_RP_LTR | PCIE_RP_AER, + }" + chip soc/intel/common/block/pcie/rtd3 + register "enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_H13)" + register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_H12)" + register "srcclk_pin" = "3" + device generic 0 on end + end + probe SD_CARD SD_GL9750S + end + device ref emmc on + probe STORAGE STORAGE_EMMC + end + device ref ish on + chip drivers/intel/ish + register "add_acpi_dma_property" = "true" + device generic 0 on end + end + probe STORAGE STORAGE_UFS + end + device ref ufs on + probe STORAGE STORAGE_UFS + end + device ref pch_espi on + chip ec/google/chromeec + use conn0 as mux_conn[0] + use conn1 as mux_conn[1] + device pnp 0c09.0 on end + end + end + device ref pmc hidden + chip drivers/intel/pmc_mux + device generic 0 on + chip drivers/intel/pmc_mux/conn + use usb2_port1 as usb2_port + use tcss_usb3_port1 as usb3_port + device generic 0 alias conn0 on end + end + chip drivers/intel/pmc_mux/conn + use usb2_port2 as usb2_port + use tcss_usb3_port2 as usb3_port + device generic 1 alias conn1 on end + end + end + end + end + device ref tcss_xhci on + chip drivers/usb/acpi + device ref tcss_root_hub on + chip drivers/usb/acpi + register "desc" = ""USB3 Type-C Port C0 (MLB)"" + register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" + register "use_custom_pld" = "true" + register "custom_pld" = "ACPI_PLD_TYPE_C(LEFT, LEFT, ACPI_PLD_GROUP(1, 1))" + device ref tcss_usb3_port1 on end + end + chip drivers/usb/acpi + register "desc" = ""USB3 Type-C Port C1 (DB)"" + register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" + register "use_custom_pld" = "true" + register "custom_pld" = "ACPI_PLD_TYPE_C(RIGHT, RIGHT, ACPI_PLD_GROUP(2, 1))" + device ref tcss_usb3_port2 on end + end + end + end + end + device ref xhci on + chip drivers/usb/acpi + device ref xhci_root_hub on + chip drivers/usb/acpi + register "desc" = ""USB2 Type-C Port C0 (MLB)"" + register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" + register "use_custom_pld" = "true" + register "custom_pld" = "ACPI_PLD_TYPE_C(LEFT, LEFT, ACPI_PLD_GROUP(1, 1))" + device ref usb2_port1 on end + end + chip drivers/usb/acpi + register "desc" = ""USB2 Type-C Port C1 (DB)"" + register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" + register "use_custom_pld" = "true" + register "custom_pld" = "ACPI_PLD_TYPE_C(RIGHT, RIGHT, ACPI_PLD_GROUP(2, 1))" + device ref usb2_port2 on end + end + chip drivers/usb/acpi + register "desc" = ""USB2 Type-A Port A0 (MLB)"" + register "type" = "UPC_TYPE_A" + register "use_custom_pld" = "true" + register "custom_pld" = "ACPI_PLD_TYPE_A(LEFT, RIGHT, ACPI_PLD_GROUP(3, 1))" + device ref usb2_port3 on end + end + chip drivers/usb/acpi + register "desc" = ""USB2 Type-A Port A1 (DB)"" + register "type" = "UPC_TYPE_A" + register "use_custom_pld" = "true" + register "custom_pld" = "ACPI_PLD_TYPE_A(RIGHT, LEFT, ACPI_PLD_GROUP(4, 1))" + device ref usb2_port4 on + probe DB_USB DB_1C_1A + end + end + chip drivers/usb/acpi + register "desc" = ""USB2 Camera"" + register "type" = "UPC_TYPE_INTERNAL" + device ref usb2_port6 on end + end + chip drivers/usb/acpi + register "desc" = ""USB2 Camera"" + register "type" = "UPC_TYPE_INTERNAL" + device ref usb2_port7 on end + end + chip drivers/usb/acpi + register "desc" = ""USB2 Bluetooth"" + register "type" = "UPC_TYPE_INTERNAL" + register "reset_gpio" = + "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D4)" + device ref usb2_port8 on end + end + chip drivers/usb/acpi + register "desc" = ""USB3 Type-A Port A0 (MLB)"" + register "type" = "UPC_TYPE_USB3_A" + register "use_custom_pld" = "true" + register "custom_pld" = "ACPI_PLD_TYPE_A(LEFT, RIGHT, ACPI_PLD_GROUP(3, 1))" + device ref usb3_port1 on end + end + chip drivers/usb/acpi + register "desc" = ""USB3 Type-A Port A1 (DB)"" + register "type" = "UPC_TYPE_USB3_A" + register "use_custom_pld" = "true" + register "custom_pld" = "ACPI_PLD_TYPE_A(RIGHT, LEFT, ACPI_PLD_GROUP(4, 1))" + device ref usb3_port2 on + probe DB_USB DB_1C_1A + end + end + end + end + end + end end |