diff options
Diffstat (limited to 'src/mainboard/broadcom/blast/Options.lb')
| -rw-r--r-- | src/mainboard/broadcom/blast/Options.lb | 260 |
1 files changed, 0 insertions, 260 deletions
diff --git a/src/mainboard/broadcom/blast/Options.lb b/src/mainboard/broadcom/blast/Options.lb deleted file mode 100644 index 208a6c7433..0000000000 --- a/src/mainboard/broadcom/blast/Options.lb +++ /dev/null @@ -1,260 +0,0 @@ -uses CONFIG_GENERATE_MP_TABLE -uses CONFIG_GENERATE_PIRQ_TABLE -uses CONFIG_GENERATE_ACPI_TABLES -uses CONFIG_HAVE_ACPI_RESUME -uses CONFIG_USE_FALLBACK_IMAGE -uses CONFIG_HAVE_FALLBACK_BOOT -uses CONFIG_HAVE_HARD_RESET -uses CONFIG_IRQ_SLOT_COUNT -uses CONFIG_HAVE_OPTION_TABLE -uses CONFIG_MAX_CPUS -uses CONFIG_MAX_PHYSICAL_CPUS -uses CONFIG_LOGICAL_CPUS -uses CONFIG_IOAPIC -uses CONFIG_SMP -uses CONFIG_FALLBACK_SIZE -uses CONFIG_ROM_SIZE -uses CONFIG_ROM_SECTION_SIZE -uses CONFIG_ROM_IMAGE_SIZE -uses CONFIG_ROM_SECTION_SIZE -uses CONFIG_ROM_SECTION_OFFSET -uses CONFIG_ROM_PAYLOAD -uses CONFIG_COMPRESSED_PAYLOAD_LZMA -uses CONFIG_PRECOMPRESSED_PAYLOAD -uses CONFIG_ROMBASE -uses CONFIG_XIP_ROM_SIZE -uses CONFIG_XIP_ROM_BASE -uses CONFIG_STACK_SIZE -uses CONFIG_HEAP_SIZE -uses CONFIG_USE_OPTION_TABLE -uses CONFIG_LB_CKS_RANGE_START -uses CONFIG_LB_CKS_RANGE_END -uses CONFIG_LB_CKS_LOC -uses CONFIG_MAINBOARD_PART_NUMBER -uses CONFIG_MAINBOARD_VENDOR -uses CONFIG_MAINBOARD -uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID -uses CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID -uses COREBOOT_EXTRA_VERSION -uses CONFIG_RAMBASE -uses CONFIG_TTYS0_BAUD -uses CONFIG_TTYS0_BASE -uses CONFIG_TTYS0_LCS -uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL -uses CONFIG_MAXIMUM_CONSOLE_LOGLEVEL -uses CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL -uses CONFIG_CONSOLE_SERIAL8250 -uses CONFIG_HAVE_INIT_TIMER -uses CONFIG_GDB_STUB -uses CONFIG_GDB_STUB -uses CONFIG_CROSS_COMPILE -uses CC -uses HOSTCC -uses CONFIG_OBJCOPY -uses CONFIG_CONSOLE_VGA -uses CONFIG_PCI_ROM_RUN -uses CONFIG_HW_MEM_HOLE_SIZEK -uses CONFIG_HT_CHAIN_UNITID_BASE -uses CONFIG_HT_CHAIN_END_UNITID_BASE -uses CONFIG_SB_HT_CHAIN_ON_BUS0 - -uses CONFIG_USE_DCACHE_RAM -uses CONFIG_DCACHE_RAM_BASE -uses CONFIG_DCACHE_RAM_SIZE -uses CONFIG_USE_INIT -uses CONFIG_USE_PRINTK_IN_CAR - -uses CONFIG_SB_HT_CHAIN_UNITID_OFFSET_ONLY - -### -### Build options -### - -## -## CONFIG_ROM_SIZE is the size of boot ROM that this board will use. -## -default CONFIG_ROM_SIZE=524288 - -## -## CONFIG_FALLBACK_SIZE is the amount of the ROM the complete fallback image will use -## -default CONFIG_FALLBACK_SIZE = CONFIG_ROM_IMAGE_SIZE - -## -## Build code for the fallback boot -## -default CONFIG_HAVE_FALLBACK_BOOT=1 - -## -## Build code to reset the motherboard from coreboot -## -default CONFIG_HAVE_HARD_RESET=1 - -## -## Build code to export a programmable irq routing table -## -default CONFIG_GENERATE_PIRQ_TABLE=1 -default CONFIG_IRQ_SLOT_COUNT=11 - -## -## Build code to export an x86 MP table -## Useful for specifying IRQ routing values -## -default CONFIG_GENERATE_MP_TABLE=1 - -## -## Build code to export a CMOS option table -## -default CONFIG_HAVE_OPTION_TABLE=1 - -## -## Move the default coreboot cmos range off of AMD RTC registers -## -default CONFIG_LB_CKS_RANGE_START=49 -default CONFIG_LB_CKS_RANGE_END=122 -default CONFIG_LB_CKS_LOC=123 - -## -## Build code for SMP support -## Only worry about 2 micro processors -## -default CONFIG_SMP=1 -default CONFIG_MAX_CPUS=4 -default CONFIG_MAX_PHYSICAL_CPUS=2 -default CONFIG_LOGICAL_CPUS=1 - -#1G memory hole -default CONFIG_HW_MEM_HOLE_SIZEK=0x100000 - -#VGA Console -#default CONFIG_CONSOLE_VGA=1 -#default CONFIG_PCI_ROM_RUN=1 - -#HT Unit ID offset -default CONFIG_HT_CHAIN_UNITID_BASE=0x6 - -#real SB Unit ID -default CONFIG_HT_CHAIN_END_UNITID_BASE=0x1 - -#make the SB HT chain on bus 0 -default CONFIG_SB_HT_CHAIN_ON_BUS0=1 - -## -## enable CACHE_AS_RAM specifics -## -default CONFIG_USE_DCACHE_RAM=1 -default CONFIG_DCACHE_RAM_BASE=0xcf000 -default CONFIG_DCACHE_RAM_SIZE=0x1000 -default CONFIG_USE_INIT=0 - -## -## Build code to setup a generic IOAPIC -## -default CONFIG_IOAPIC=1 - -## -## Clean up the motherboard id strings -## -default CONFIG_MAINBOARD_PART_NUMBER="blast" -default CONFIG_MAINBOARD_VENDOR="Broadcom" -default CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID=0x161f -default CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID=0x3050 - - -### -### coreboot layout values -### - -## CONFIG_ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy. -default CONFIG_ROM_IMAGE_SIZE = 65536 - -## -## Use a small 8K stack -## -default CONFIG_STACK_SIZE=0x2000 - -## -## Use a small 16K heap -## -default CONFIG_HEAP_SIZE=0x4000 - -## -## Only use the option table in a normal image -## -default CONFIG_USE_OPTION_TABLE = !CONFIG_USE_FALLBACK_IMAGE - -## -## Coreboot C code runs at this location in RAM -## -default CONFIG_RAMBASE=0x00004000 - -## -## Load the payload from the ROM -## -default CONFIG_ROM_PAYLOAD = 1 - -### -### Defaults of options that you may want to override in the target config file -### - -## -## The default compiler -## -default CC="$(CONFIG_CROSS_COMPILE)gcc -m32" -default HOSTCC="gcc" - -## -## Disable the gdb stub by default -## -default CONFIG_GDB_STUB=0 - -default CONFIG_USE_PRINTK_IN_CAR=1 - -## -## The Serial Console -## - -# To Enable the Serial Console -default CONFIG_CONSOLE_SERIAL8250=1 - -## Select the serial console baud rate -default CONFIG_TTYS0_BAUD=115200 -#default CONFIG_TTYS0_BAUD=57600 -#default CONFIG_TTYS0_BAUD=38400 -#default CONFIG_TTYS0_BAUD=19200 -#default CONFIG_TTYS0_BAUD=9600 -#default CONFIG_TTYS0_BAUD=4800 -#default CONFIG_TTYS0_BAUD=2400 -#default CONFIG_TTYS0_BAUD=1200 - -# Select the serial console base port -default CONFIG_TTYS0_BASE=0x3f8 - -# Select the serial protocol -# This defaults to 8 data bits, 1 stop bit, and no parity -default CONFIG_TTYS0_LCS=0x3 - -## -### Select the coreboot loglevel -## -## EMERG 1 system is unusable -## ALERT 2 action must be taken immediately -## CRIT 3 critical conditions -## ERR 4 error conditions -## WARNING 5 warning conditions -## NOTICE 6 normal but significant condition -## INFO 7 informational -## CONFIG_DEBUG 8 debug-level messages -## SPEW 9 Way too many details - -## Request this level of debugging output -default CONFIG_DEFAULT_CONSOLE_LOGLEVEL=8 -## At a maximum only compile in this level of debugging -default CONFIG_MAXIMUM_CONSOLE_LOGLEVEL=8 - -## -## Select power on after power fail setting -default CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL="MAINBOARD_POWER_ON" - -### End Options.lb -end |